BG17C

BeRex 5-4000 MHz Cascadeable InGaP HBT Gain Block Device Features  31dBm Output IP3 at 2dBm/tone at 900MHz  18dB Gain at 500MHz  17.5dBm P1dB at 900MHz  Highly Reliable InGaP/GaAs HBT Technology  Temperature Compensation Circuit patent  SOT-89 Surface Mount Package  50 ohm Cascadeable  Lead-free/Green/RoHS compliant Application: commercial, space, military wireless system Electrical Specifications (Ta = 25C, Vs = 5V) Parameters Test Conditions Frequency Range Gain 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz 500 MHz 900 MHz 1900 MHz 2450 MHz Vc = 5.0V BG17C Min 5 17.0 16.8 15.4 14.6 Typ 18.0 17.8 16.4 15.6 -20.0 -16.0 -35.0 -20.0 -17.0 -17.0 -15.0 -12.0 31.0 31.0 30.0 29.0 17.1 17.5 17.0 16.1 55 5.0 -0.004 50 Max 4000 19.0 18.8 17.4 16.6 Unit MHz dB S11 dB S22 dB OIP3 P1dB Ic Vc dG/dT Rth 29.0 29.0 28.0 27.0 16.1 16.5 16.0 15.1 45 dBm dBm 65 mA V dB/C C/W Thermal Resistance Test conditions unless otherwise noted. 1. Device performance is measured on BeRex evaluation board at 25C, 50 ohm system. 2. OIP3 measured with two tones at an output power of 2dBm/tone separated by 1MHz. http: //www.berex.com BeRex Absolute Maximum Ratings Parameters Operating Case temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power BG17C Rating -40 to +85C -55 to +155C +220C 6.5V 150mA 23dBm Operation of this device above any of these parameters may result in permanent damage. [I-V Characteristics] 100 [Generic SOT89 Evaluation Board] +25C 80 Icc [mA] -30C +85C BeRex Evaluation Board 60 40 20 0 0 1 2 3 4 5 6 MMIC Innovator Vcc [V] *Dielectric constant is 4.2 *RF pattern width 52mil *31mil thick FR4 PCB Application Circuit: 5 - 4000 MHz Schematic Diagram C3 C4 C5 +5V BOM C1 C2 100pF 100pF 100pF 1000pF 10uF 33nH Tolerance ± 5% ± 5% ± 5% ± 5% ± 20% 5% L1 RFin C1 BG17C C3 C2 RFout C4 C5 *L1 *Note: Less than 20nH improves RF performance at frequencies over 1.9GHz. 40nH or higher value L1 improves RF performance at frequencies under 500MHz. Optimum value of L1 may vary with board design. http: //www.berex.com BeRex Typical Device Data BG17C S-parameters (Vc=5V, Ic=55mA, T=25C) (Vdevice = 5.0V, Icc = 55mA, T = 25 C) Freq [MHz] 100 500 1000 1500 2000 2500 3000 3500 4000 S11 Mag 0.69 0.18 0.05 0.01 0.09 0.20 0.27 0.25 0.11 S11 Ang -38.43 -118.50 160.30 37.15 -127.10 -163.40 168.40 137.30 108.30 S21 Mag 4.94 7.99 7.76 7.31 6.49 6.07 5.57 5.33 5.18 S-Parameter S21 Ang -122.90 126.10 48.67 -22.00 -91.16 -156.00 142.10 76.86 10.32 S12 Mag 0.04 0.08 0.08 0.08 0.08 0.08 0.08 0.09 0.09 S12 Ang 86.86 -28.03 -90.43 -144.70 162.40 111.90 61.34 9.56 -45.02 S22 Mag 0.77 0.18 0.08 0.16 0.25 0.31 0.35 0.31 0.16 S22 Ang 170.20 39.68 -78.90 -154.80 175.50 156.20 134.50 104.60 47.31 http: //www.berex.com BeRex BG17C Typical Performance (Vc = 5V, Ic = 55mA, Ta = 25C) Freq MHz 500 900 1900 2140 S21 dB 18.0 17.8 16.4 16.0 S11 dB -15.0 -14.0 -24.0 -16.0 S22 dB -14.0 -22.0 -12.0 -11.0 P1 dBm 17.1 17.5 17.0 17.0 OIP3 dBm 31.0 31.0 30.0 30.0 NF dB 3.8 3.9 4.0 4.0 2450 15.6 -14.0 -10.0 16.1 29.0 4.0 3000 15.0 -11.0 -9.0 15.2 28.0 4.2 3500 14.9 -20 -12.1 15 27.5 4.2 Typical Performance (V device = 4.7 V, Ic = 43 mA, Ta = 25 ℃) Freq S21 S11 S22 P1 OIP3 NF MHz dB dB dB dBm dBm dB 70 20.0 -13 -5.9 13.9 28.5 3.8 500 18.0 -20.2 -10.9 14.4 26 3.8 900 17.6 -24 -14.7 14.9 27.5 3.9 1900 16.0 -15.3 -10.4 14.2 27.5 4.0 2140 15.8 -14.6 -10.1 13.9 26.5 4.0 2450 15.5 -16.7 -11.2 14.6 27 4.0 3500 14.7 -18.9 -11.9 14.0 26 4.2 Typical Performance (V device = 4.5 V, Ic = 37 mA, Ta = 25 ℃) Freq S21 S11 S22 P1 OIP3 NF MHz dB dB dB dBm dBm dB 70 19.5 -12.5 -5.8 13.6 27.5 3.8 500 17.8 -18.7 -10.5 14.3 27.0 3.8 900 17.4 -21.7 -13.9 14.3 24.5 3.9 1900 15.9 -14.7 -10.1 13.7 24.5 4.0 2140 15.7 -14.1 -9.7 13.2 24 4.0 2450 15.3 -16.1 -10.9 12.7 24.0 4.0 3500 14.6 -18 -11.6 12.5 23.5 4.2 http: //www.berex.com BeRex WCDMA 4FA 2140 -60dBc BG17C WCDMA 6FA 2140 -60dBc http: //www.berex.com BeRex BG17C ACLR Device Performance Pin-Pout-Gain 25 20 15 10 5 0 -15 35% 30% 25% 25 20 15 15% 10 10% 5 0 -15 5% 0% -10 -5 Pin [dBm ] 0 5 30% 25% 20% Po/G Po/G PAE 15% 10% 5% 0% -10 -5 Pin [dBm ] 0 5 900MHz, 5V/55mA 1900 MHz, 5V/55mA http: //www.berex.com PAE 20% BeRex BG17C OIP3 F1=500, F2=501MHz 35 35 F1=900, F2=901MHz 33 33 OIP3 [dBm] OIP3 [dBm] 31 31 29 29 27 +25C 25 4 6 8 10 12 -30C +85C 27 +25C 25 4 6 8 10 12 -30C +85C Po,tot [dBm ] Po,tot [dBm ] F1=1900, F2=1901MHz 35 +25C 33 -30C +85C F1=2140, F2=2141MHz 35 +25C 33 -30C +85C OIP3 [dBm] 31 OIP3 [dBm] 4 6 8 10 12 31 29 29 27 27 25 25 4 6 8 10 12 Po,tot [dBm ] Po,tot [dBm ] F1=2450, F2=2451MHz 32 +25C 30 -30C +85C 33 35 OIP3 Po=2dBm /tone, D F=1MHz OIP3 [dBm] 28 OIP3 [dBm] 31 26 29 24 27 +25C -30C 1500 2000 +85C 2500 22 4 6 8 10 12 25 500 1000 Po,tot [dBm ] Freq [MHz] http: //www.berex.com BeRex ACPR F=500MHz, IS-95A, 9CH-FWD 885KHz Offset 0 +25C -10 -30C +85C BG17C F=900MHz, IS-95A, 9CH-FWD 885KHz Offset 0 -10 +25C -30C +85C ACPR [dBc] -20 -30 -40 -50 -60 -70 4 6 8 10 12 ACPR [dBc] -20 -30 -40 -50 -60 -70 -80 4 6 8 10 12 Po [dBm ] Po [dBm ] F=1900MHz, IS-95A, 9CH-FWD 885KHz Offset 0 +25C -10 -30C +85C IS-95A, 9CH-FWD, 885KHz Offset Po satisfies -45dBc 10 8 ACPR [dBc] -20 Po [dBm] -30 -40 -50 6 4 2 -60 -70 4 6 8 10 12 +25C 0 500 -30C +85C 1000 1500 2000 Po [dBm ] Freq [MHz] Gain Flatness Gain vs Temperature 20 18 S21 [dB] 16 14 12 10 0 500 1000 1500 2000 Freq [MHz] 2500 3000 3500 4000 +25C -30C +85C http: //www.berex.com BeRex BG17C Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern PCB Mounting 0.40 1.30 0.40 Ø0.40 0.40 0.75 1.20 1.20 1.20 1.20 1.50 1.00 0.65 2.80 2.00 0.50 Note : All dimension are in millimeters Visit http://www.berex.com for PCB layout http: //www.berex.com BeRex BG17C Tape & Reel SOT89 Packaging information: Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish. (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns) MSL / ESD Rating ESD Rating: Value: Test: Standard: MSL Rating: Standard: Class 2 Passes