3371R10KT5L.5XX

MODEL 3371 1-5/16” Diameter Single Turn Conductive Plastic Precision Potentiometer / Position Sensor ELECTRICAL 2 Resistance Range, Ohms Standard Resistance Tolerance Minimum Practical Resistance Tolerance Independent Linearity* Minimum Practical Independent Linearity Input Voltage, Maximum Power Rating, Watts Dielectric Strength Insulation Resistance, Minimum Output Smoothness, Maximum Actual Electrical Travel, Nominal Electrical Continuity Travel, Minimum End Voltage, Maximum Tap Tolerance Resolution Temperature Coefficient** * Linearity is measured between 1% and 99% of input voltage. ** Special tempco available to ± 100ppm/˚C. ENVIRONMENTAL (MIL-R-39023) 1K to 900K ±10% ±5% ±0.5% ±0.25% 400Vdc not to exceed power rating .75 at 65°C derating to 0 at 105°C 1,000V rms 1,000 Megohms 0.1% 348° 350° 0.5% of Input Voltage 0.5% of Input Voltage Essentially infinite –800 ppm/°C Operating Temperature Range Temperature Cycling Shock, 6ms Sawtooth Vibration Moisture Resistance High Temperature Exposure Rotational Life Rotational Load Life Specifications subject to change without notice. –25°C to +105°C 5 cycles, –25°C to +105°C (10% ∆R) 100G’s (0.1ms discontinuity max.) 10G’s, 10 to 500 Hz (2% ∆R, 0.1ms discontinuity max.) Five 24 hour cycles (25% ∆R) Mechanical operation at 105°C (0.5% ∆R) 2 mil. shaft rev. 2 mil. shaft rev. (10% ∆R) 2-31 Model 3371 MECHANICAL Total Mechanical Travel Number of Gangs, Maximum Weight, Nominal Shaft Runout, T.I.R., Maximum Pilot Diameter Runout, T.I.R., Maximum Lateral Runout, T.I.R., Maximum Shaft Radial Play, Maximum Shaft End Play, Maximum Start/Run Torque, Maximum SPECIAL FEATURES 360° continuous (350° ±2° with stop feature) 1 1.5 oz. .0025” .0025” .003” .004” .007” 1.0 oz.-in Center Tap Linearity Tape Flatted Shaft Slotted Shaft Shaft Lock Stop FEATURES/BENEFITS CT LT FS SS SL ST • Low noise • Excellent “output” smoothness STANDARD RESISTANCE VALUES, OHMS 1K 2K 5K 10K 20K 50K 100K METRIC CONVERSIONS 1 in. 1 oz. 25.4mm 28.4 gm 1 oz.-in. 1 lb.-in. 0,007 N-m 0,113 N-m 2-32 Model 3371 OUTLINE DIMENSIONS (Inch/mm) .891±.031 22.6±0.79 .734±.016 18.6±0.41 Mounting Surface .875±.031 22.2±0.79 .062±.016 1.58±0.41 .2497 +.0000 -.0003 Dia. 6.342 +0.000 -0.008 .031±.016 0.79±0.41 2 CW CCW 1.312±.016 33.33±0.41 Slider CT CT When Specified .062±.016 1.58±0.41 .375±.016 9.53±0.41 .406 +.000 -.002 Dia. 10.3 +0.00 -0.05 Chamfer .016 Max. x 45° 0.41 3/8-32 UNEF Thread .562±.016 14.3±0.41 Locating Lug: .125±.005 Dia. 3.18±0.13 ORDERING INFORMATION 3371 R 10K T5 L .5 XX Model Series Resistance Prefix Resistance Value Linearity Optional Non-Standard Tolerance Optional Special Feature Code CIRCUIT DIAGRAM NOTES (S) (CCW) (CW) Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees INCH mm 2-33 Model 3371