HM70251R315LFTR13

Electrical / Environmental  RoHil aSt n Comp High Power Shielded Low Profile Surface Mount Inductors • Operating Temperature Range • Temperature Rise, Maximum -40°C to +180°C 50°C Specifications Inductance 100kHz, 0.1V @ Isat @ 0 Adc (µH) (µH±20%) Typ. Min. Typ. 1.00 1.33 1.94 0.83 1.50 2.10 1.30 1.50 1.20 1.60 0.70 1.20 5.00 10.0 1.20 2.00 0.63 0.93 1.28 0.488 0.80 1.12 0.80 0.97 0.92 1.15 0.40 0.80 3.60 6.80 0.80 1.20 0.70 1.16 1.60 0.61 1.00 1.40 1.00 1.20 1.02 1.44 0.52 0.90 4.30 8.00 1.00 1.60 DCR (m Ω ) Typ. 2.53 3.38 4.71 1.75 2.16 3.48 2.16 4.00 1.75 2.13 1.05 1.68 6.50 12.0 1.37 2.20 (1) Part Number HM70-101R0LF HM70-201R3LF HM70-201R9LF HM70-25R80LF HM70-301R5LF HM70-302R0LF HM70-321R3LF HM70-351R5LF HM70-401R2LF HM70-401R6LF HM70-50R70LF HM70-501R2LF HM70-505R0LF HM70-50100LF HM70-601R2LF HM70-602R0LF Notes: Isat @ 25°C (Adc) 16 16 12 18 16 12 16 18 18 20 30 24 7 7 20 15 (2) Max. 2.90 3.74 5.42 2.01 2.48 4.00 2.48 4.50 1.80 2.36 1.26 2.00 8.00 15.0 1.58 2.60 Heating Current (Adc) ∆T=50°C 15 13 11 19 17 14 17 13 22 20 31 25 13 9 28 22 (3) Core Loss Factor K1 9.07E-11 1.24E-10 1.24E-10 1.51E-10 1.40E-10 1.53E-10 1.66E-10 1.35E-10 1.80E-10 1.67E-10 1.99E-10 1.99E-10 2.21E-10 2.21E-10 2.21E-10 2.21E-10 (4) K2 170.67 157.15 189.83 118.84 183.07 196.09 140.35 166.20 129.45 151.67 88.15 110.82 219.63 316.67 108.94 143.34 Fig. 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 (1) DC resistance is measured at 25°C (2) The saturation current (Isat) is the current at which the inductance will be decreased by 20% from its initial (zero DC) value. (3) The heating current is the DC current, which causes the component temperature to increase by approximately 50°C. This current is determined by soldering the component on a typical application PCB, and then apply the current to the device for 30 minutes. (4) Core Loss approximation is based on published core data: Core Loss (Pfe) = K1 * (f)1.338 * (K2∆I)2.2546 Where: core loss in watt f = frequency in kHz K1 and K2 = core loss factor ∆I = delta I across the component in Amp. K2∆I = one half of the peak to peak flux density across the component in Gauss Electrical Characteristics @ 25°C (A) Case size 10, 20, 25, 30 & 40 2007/08 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 67 Electrical Characteristics @ 25°C (Cont’d) (B) Case size 50 & 60 68 MAGNETIC COMPONENTS SELECTOR GUIDE 2007/08 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Outline Dimensions (mm) Figure 1 Top View Bottom View Top View Figure 2 Bottom View Recommended Solder Pad Layout Case size 10 20 25 30 32 35 40 50 60 A 9.00 9.00 9.00 9.00 9.00 10.7 11.0 13.5 14.0 B 10.5 10.5 10.5 10.5 10.5 10.25 12.6 12.9 13.0 C 3.70 4.50 5.00 5.20 5.60 4.20 5.20 5.50 5.80 D 4.80 4.80 4.80 4.80 4.80 5.60 6.20 6.50 6.50 E 1.70 1.70 1.70 1.70 1.70 1.70 2.30 2.30 2.30 F 6.00 6.00 6.00 6.00 6.00 6.00 7.50 7.50 7.50 G 8.30 8.00 8.30 8.00 8.00 10.6 10.7 13.5 14.0 H 2.30 2.00 2.30 2.00 2.00 5.60 3.70 6.50 6.50 I 6.00 6.00 6.00 6.00 6.00 6.20 7.50 7.50 7.50 J 2.80 2.80 2.80 2.80 2.80 2.10 3.10 3.00 3.00 K 3.00 3.00 3.00 3.00 3.00 2.50 3.50 3.50 3.50 Packaging Standard: Embossed Tape & Reel Reel: Diameter: Capacity: = Case size 10,20,25,30,32 = Case size 35,40,50,60 = 13” (330.2mm) 500 Units 400 Units Ordering Information Model Series Case Size Inductance Code: First 2 digits are significant. Last digit denotes the number of trailing zeros. For values below 10µH, “R” denotes the decimal point. HM70 50 1R2 LF TR13 Lead-Free TR - Tape & Reel Packing 13 - 13” reel 2007/08 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE www.bitechnologies.com We reserve the right to change specifications without prior notice 69