M143331GM1

MODEL M SERIES Thick Film Low Profile SIP Conformal Coated Resistor Networks ELECTRICAL Standard Resistance Range, Ohms Standard Resistance Tolerance, at 25°C Operating Temperature Range Temperature Coefficient of Resistance Temperature Coefficient of Resistance Tracking Maximum Operating Voltage Insulation Resistance, Minimum ENVIRONMENTAL 22 to 1Meg ±2% (G Tol.) Optional: ±1% (F Tol.), ±5% (J Tol.) -55°C to +125°C ±200ppm/°C ±50ppm/°C 100Vdc or √PR 10,000 Megohms 4 Thermal Shock plus Power Conditioning Short Time Overload Terminal Strength Moisture Resistance Mechanical Shock Vibration Shock Low Temperature Storage High Temperature Exposure Load Life, 1,000 Hours Resistance to Solder Heat (Per MIL-STD-202, Method 210, Cond.B) Dielectric Withstanding Voltage Marking Permanency Lead Solderability Flammability Storage Temperature Range Specifications subject to change without notice. ∆R 0.50% ∆R 0.25% ∆R 0.25% ∆R 0.50% ∆R 0.25% ∆R 0.25% ∆R 0.25% ∆R 0.50% ∆R 1.00% ∆R 0.25% 100V for 1 minute per MIL-STD-202, Method 215 per MIL-STD-202, Method 208 UL-94V-O Rated -55°C to +150°C 4-49 Model M Series MECHANICAL Lead Material Substrate Material Resistor Material Body Material STANDARD RESISTANCE VALUES, OHMS Solder Coated Steel Alloy Alumina Cermet Conformal Epoxy Resin POWER DISSIPATION, WATTS AT 70°C -3 Circuit (Isolated Resistors) & -1 Circuits (Bussed Resistors) Ohms 22 27 33 39 47 51 56 68 82 100 120 150 180 200 220 270 330 390 470 510 560 680 Ohms R1/R2 Code 220 270 330 390 470 510 560 680 820 101 121 151 181 201 221 271 331 391 471 511 561 681 Code R1/R2 Ohms 820 1K 1.2K 1.5K 1.8K 2K 2.2K 2.7K 3.3K 3.9K 4.7K 5.1K 5.6K 6.8K 8.2K 10K 12K 15K 18K 20K 22K 27K Ohms R1/R2 Code 821 102 122 152 182 202 222 272 332 392 472 512 562 682 822 103 123 153 183 203 223 273 Code R1/R2 Ohms 33K 39K 47K 51K 56K 68K 82K 100K 120K 150K 180K 200K 220K 270K 330K 390K 470K 510K 560K 680K 820K 1Meg Ohms R1/R2 3K/6.2K Code 333 393 473 513 563 683 823 104 124 154 184 204 224 274 334 394 474 514 564 684 824 105 Code R1/R2 302/622 —— Resistor (Per Circuit) —— Model M6 M8 M10 Package .6 .8 1.0 -1 .125 .125 .125 -3 .200 .200 .200 -5 .125 .125 .125 -5 Circuit (Dual Terminators) -5 Circuit (Dual Terminators) 180/390 181/391 220/270 221/271 220/330 221/331 330/390 331/391 330/470 331/471 330/680 331/681 4-50 Model M Series OUTLINE DIMENSIONS (Inch/mm) "L" Max. .195 Max. 4.95 .140±.020 3.56±0.51 .095 Max. 2.41 .100±.005 2.54±0.13 Pitch NonAccumulative .020±.004 0.51±0.10 .012±.003 0.31±0.08 Centered on Package # of Leads Dim. “L” Max. 4 .40 10.16 5 .50 12.70 6 .60 15.24 7 .70 17.78 8 .80 20.32 9 .90 22.86 10 1.00 25.40 11 1.10 27.94 12 1.20 30.48 13 1.30 33.02 14 1.40 35.56 4 SCHEMATICS -3 Circuit Isolated Resistors -1 Circuit Bussed Resistors -5 Circuit Dual Terminator 1 2 3 4 n 1 2 3 4 n 1 2 3 4 n TYPICAL PART MARKING Logo M 8 3 103 Lead #1 Indicator Model Series Date Code: (Optional Location) Resistance Code Circuit Type: -1 = Bussed -3 = Isolated -5 = Dual Terminator Number of Leads: 4 to 14 Note: Model # and number of leads not marked on 4 and 5 lead packages. 4-51 Model M Series PACKAGING Standard: Bulk: Option: Quantity = 200 Units Tape in Ammo Box All Units oriented with lead #1 to the left of direction of feed. Tape: Width Pitch Ammo Box: Capacity = = = 18mm 12.7mm 1,000 Units Option: Magazines Dimensions conform to EIA & JEDEC standards. All units oriented with lead #1 to the same side. Magazine: Material = Antistatic Plastic ORDERING INFORMATION M85 Model Series Number of Leads: 4 thru 14 Circuit Type: -3 = Isolated -1 = Bussed -5 = Dual Terminator 331 / 471 J XX Packaging Option: AP = Ammo Pack M1 or M2 Tube* Tolerance Code: F = ±1% G = ±2% (Standard) J = ±5% R2 Resistance Code (Add for -5 circuit only) Resistance Code: First 2 digits are significant (3 digits for ±1%). Last digit denotes number of trailing zeros. * Refer to Packaging for Automation Section (Page A-4) for M1 & M2 tube capacity and dimensions APPLICABLE DOCUMENTS MIL-R-83401 — Resistor Networks, Fixed, Film, General Specifications MIL-STD-105 — Sampling Procedures and Tables for Inspection by Attributes MIL-STD-202 — Test Methods for Electronic and Electrical Component Parts 4-52 Model M Series