MPI-925A

厂商：
BOSER
封装：
描述：
MPI-925A - 250W AC-DC AT Power Supply - BOSER Technology Co., Ltd

数据手册：

下载MPI-925A.pdf

立即购买

详情介绍
数据手册
价格&库存

MPI-925A 数据手册

MPI-925A 250W AC-DC AT Power Supply 2.0 0.42 0.42 11.0 DC OUTPUT WIRES Industrial Power Supply 14.4 15.0 0.5 13.80 4-TAPPING#6-32 14.0 AC-DC 6.4 2.7 1.6 Features 4.8 0.5 11.5 *Input Voltage: 90~265VAC *Input Frequency: 47~63Hz *Inrush Current: Does not exceed 30A at 115VAC input or 60A AC input, at cold start 25oC *Safety: UL 1950 / CSA 22.2 No.234 / VDE EN60950 *Load Range: When all outputs are at 60% rated load *EMI: FCC class B / EN55022B condition, the +5V output is set between 4.90~5.10V and all *EMS: Level 3 of IEC-801, 802, 803, 804 other outputs are within the specified voltage accuracy range *Ripple And Noise: Peak to peak ripple and noise for each output is < 1% of each output voltage at rated load Output PIN 115~230VAC +5V Red *Line Regulation: < +/-1% at rated load with +/-10% change +12V Yellow in input voltage -12V Brown *Load Regulation: The output voltage load regulation is less -5V Blue than the values on the table when each output loading changes Black GND +/-40% from 60% rated load while all other outputs at 60% White P.G. rated load *Hold Up Time: 14ms typ. from the last AC line charging pulse to the point when +5V drops down to +4.75V Output Min. Rated Max. Tolerance Voltage Load Load Load *Output Power: Total DC continuous power is within 200W at +5V 1A 25A 30A +/-0.1V 40oC ambient temperature. If the input voltage is < 100VAC, +12V 0A 10A 12A +/-0.72V total DC continuous power should not exceed 180W -12V 0A 1A 2A +/-0.6V *Power Good Signal: Goes high 100~500ms after all DC -5V 0A 1A 2A +/-0.25V output is ready *Power Failure: Goes low 1ms before any DC output falls *Efficiency: > 65% at nominal line and rated load *Altitude: 10,000 feet *Protection: Built-in crowbar circuit automatically shuts down outputs to avoid damaging external circuits. Trip point of O.V.P. circuit is between 5.7~7.0V *Temperature: 0~+70oC (operating); -40~+75oC (storage) *Humidity: 5~95%; non-condensing at 40oC (operating) *Connectors: AC Input/Output: Meets IEC 320/CEE 22 standard Tab Terminals: Female 0.250" x 0.032" CPU Board: Alex 8500-06 or equivalent device 3.5" Disk Drive: AMP 1-480424-0/171822-4 or equivalent device *Dimensions: 14.0 x 15.0 x 8.62 cm with +/-0.8mm and +/0.4mm tolerance between mounting holes *MTBF: 156,598 hrs. Safety Standards www.boser.com.tw 2.4 3.72 8.62

下载 PDF

MPI-925A

1. 物料型号：MPI-925A

2. 器件简介：这是一个250W的AC-DC AT电源供应器，用于工业电力供应。

3. 引脚分配： - Red：+5V - Yellow：+12V - Brown：-12V - Blue：-5V - Black：GND - White：P.G.（Power Good信号）

4. 参数特性： - 输入电压：90~265VAC - 输入频率：47~63Hz - 冲击电流：在115VAC输入或60A AC输入时不超过30A，在冷启动25°C时 - 负载范围：当所有输出在60%额定负载条件下，+5V输出设置在4.90~5.10V之间，所有其他输出在规定的电压精度范围内 - 纹波和噪声：每个输出的峰峰纹波和噪声小于额定负载下每个输出电压的1% - 115~230VAC - 线路调整率：在额定负载下，输入电压变化±10%时小于±1% - 负载调整率：当每个输出负载变化±40%从60%额定负载时，所有其他输出在60%额定负载下，输出电压负载调整率小于表中的值 - 保持时间：从最后一个AC线路充电脉冲到+5V下降到+4.75V时的典型时间为14ms - 输出功率：在40°C环境温度下，总DC连续功率在200W以内。如果输入电压<100VAC，总DC连续功率不应超过180W - 电源良好信号：所有DC输出准备好后100~500ms内变高 - 电源故障：在任何DC输出下降前1ms变低 - 效率：在额定线路和额定负载下大于65% - 高度：10,000英尺 - 保护：内置保险丝电路自动关闭输出以避免损坏外部电路。OVP电路的触发点在5.7~7.0V之间 - 温度：0~+70°C（运行）；-40~+75°C（存储） - 湿度：5~95%；在40°C时不凝结（运行）

5. 功能详解：该电源供应器具备多种保护功能，如内置保险丝电路、过压保护（OVP）等，以确保稳定和安全的电源输出。

6. 应用信息：适用于需要AC-DC转换的工业应用场合，如CPU板和3.5英寸软盘驱动器等设备的供电。

7. 封装信息： - 尺寸：14.0 x 15.0 x 8.62 cm，安装孔之间的公差为±0.8mm和+/0.4mm - 接口：AC输入/输出符合IEC 320/CEE 22标准，端子为0.250" x 0.032"的母头

MPI-925A 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“MPI-925A”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

MPI-925A

相关技术文章