B2405S-2WR2

B_S-2WR2 Series 4 pin SIP Package, 2 Watt, Isolated, Unregulated Features  4 pin SIP package  Input / Output Isolation Voltage: 1.5kVDC  High Efficiency  Lead Free Design, RoHS Compliant  Operating temperature: -40°C to +85°C  Optional Continuous Short Circuit Protection  Continuous Short Circuit Protection  Meet Safety Standard / Approval: IEC / EN60950-1 Applications These converters are well suitable for battery operated equipment, measurement equipment, telecom, wireless network, Industry control system, everywhere where isolated, tightly regulated voltages and compact size are required. Technical Specification All specifications are typical at nominal input, full load and 25°C unless otherwise stated. Model Number Output Voltage (V) 5 Output Current (mA) 200 79 12 80 82 470 220 15 65 82 220 B0524S-2WR2 24 65 82 100 B1205S-2WR2 5 200 79 470 12 15 80 65 82 82 220 24 65 82 220 100 5 200 79 470 12 80 82 220 15 65 82 220 24 65 82 100 Input Voltage Range(V) B0505S-2WR2 B0512S-2WR2 B0515S-2WR2 B1212S-2WR2 B1215S-2WR2 B1224S-2WR2 4.5 ~ 5.5 Nominal: 5 10.8 ~ 13.2 Nominal: 12 B2405S-2WR2 B2412S-2WR2 B2415S-2WR2 B2424S-2WR2 21.6 ~ 26.4 Nominal: 24 Full Load Efficiency .(2) (%) Capacitive Load, max. (uF) Note 1. Io below this value will not damage these converters, however, they may not meet all listed specifications. 2. Typical value, tested at nominal input and full load. 3. For each output. 4. In case of long input lines or hot plug-in requirements, we recommended to use an external low ESR capacitor (22uF) near to the converter's input pins. 5. Specifications subject to change without notice. E-mail: bothhand_sales@bothhandww.com https://www.bothhandww.com Rev: A0 Page 1 of 7 Input Specifications Input voltage Input current at no load Surge voltage (1 s max.) Recommended input fuse 5 Vin models 4.5~5.5V 12Vin models 10.8~13.2V 24Vin models 21.6~26.4V 5 Vin models 35mA(typ.) 12Vinmodels 18mA(typ.) 24Vinmodels 10mA(typ.) 5 Vin models 9V(Max.) 12Vin models 18V(Max.) 24Vin models 30V(Max.) 5 Vin models 1A (slow-blow fuse) 12Vin models 0.4A (slow-blow fuse) 24Vin models 0.2A (slow-blow fuse) Input filter Capacitor Environmental Specifications Operating ambient temperature Natural convection -40°C to +85°C Maximum case temperature +95°C Storage temperature range -55°C to +125°C Relative humidity 95% RH max. Output Specifications Output power Voltage accuracy (Nominal Vin and full load) 2 Watts max. ±3% at 60% load ±3% at 80% load 5VDC models Other models Minimum load Regulation 0A Input variation Load variation Ripple and Noise (20MHz Bandwidth) ±1.5% max.for Vin Change of 1% See graphs below 120mVp-p typ. 250mVp-p max. Maximum capacitive load See table Temperature coefficient Short Circuit Protection ±0.02%/°C max. Automatic recovery Continuous Efficiency Nominal input and full load See table Isolation voltage(60s) Input to output Isolation resistance 500VDC General Specifications 1500VDC 1GΩ min. ＜20pF. Isolation capacitance Switching frequency Start-up time 30K-200KHz. ≤10ms Nominal Vin and full load Reliability, calculated MTBF E-mail: bothhand_sales@bothhandww.com 2×10 6 Hrs https://www.bothhandww.com Rev: A0 Page 2 of 7 Physical Specifications Case material Plastic (UL94 V-0) Potting material Epoxy (UL94 V-0) Dimensions 0.46 × 0.295 × 0.4 Inch (11.6 × 7.5 × 10.2 mm) Weight 1.6g (0.057oz) typ. Pin material Tinned copper Output voltage variation dependent on load (at nominal input voltage) Other Output 10 7.5 5 2.5 0 max. -2.5 typ. -5 min. -7.5 -10 20% 40% 60% 80% Deviation of Vout nom. (%) Deviation of Vout nom. (%) 5VDC Output 10 7.5 5 max. 2.5 0 typ. -2.5 min. -5 -7.5 -10 100% 20% 40% Load (%) 60% 80% Load (%) Power Derating Curve Power Derating Curve 120 Output Power (%) 100 Natural Convection 20LFM 80 60 40 20 0 -40 -20 0 20 40 60 80 95 100 120 Ambient Temp.TA (℃) E-mail: bothhand_sales@bothhandww.com https://www.bothhandww.com Rev: A0 Page 3 of 7 100% Mechanical Dimensions Pin Assignment Pin 1 2 3 Single -Vin +Vin -Vout 4 +Vout Unit: mm (inch) Pin section tolerances:±0.1(±0.004) General tolerances:±0.5(±0.02) Test Configurations All specifications are typical at nominal input, full load and 25°C unless otherwise stated. A DC Power Supply A DC/DC converter V V Load ◎DC Power Supply: It offers a wide voltage and current range precisely. ◎Current meter (A): Accuracy200μA ~ 200mA 4 ranges+(0.2% rdg + 2 digits) 2000mA ~ 20A 2 ranges+(0.3% rdg + 2 digits). ◎Voltage meter (V): Accuracy+(0.03% rdg + 4 digits). ◎Load: At full load. ◎Wires: The resistance of the wires must be small. 1. Input voltage range: Narrow input voltage range（±10%）、wide input voltage range (2:1 and 4:1）。 E-mail: bothhand_sales@bothhandww.com https://www.bothhandww.com Rev: A0 Page 4 of 7 EX: Narrow input voltage range（±10%） 5V nominal input 4.5~5.5V 12V nominal input   10.8~13.2V 24V nominal input   21.6~26.4V Wide input voltage range 2:1 5V nominal input  4.5~9V 12V nominal input 9~18V 24V nominal input   18~36V 48V nominal input    36~75V Wide input voltage range 4:1 (W) 24V nominal input    9~36 V 48V nominal input   18~75V 2. Input power : Pin = Vin x Iin Vin：Input voltage Iin：Input current Pout = Vout x Iout Vout：Output voltage Iout：Output current 3. Output power : 4. Efficiency : Efficiency = Pout Pin x100% Pout: Output power Pin: Input power 5. Voltage accuracy: │Vout-Vout(nominal)│ Vout x100% Vout：Output voltage Vout(nominal)：Nominal output voltage 6. Line regulation: Narrow input voltage range（±10%）and unregulated output voltage series. Line regulation= ΔVout ΔVin ΔVout = Vout(+10%)-Vout(-10%) x100% Vout Vout(+10%)：Output voltage at Vin = 1.1xVin(nominal)&full load Vout(-10%)：Output voltage at Vin = 0.9xVin(nominal)&full load Vout：Output voltage at Vin = Vin(nominal)&full load ΔVin = Vin(+10%)-Vin(-10%) x100% Vin(nominal) Vin(+10%)：Input voltage = 1.1xVin(nominal) Vin(-10%)：Input voltage = 0.9xVin(nominal) E-mail: bothhand_sales@bothhandww.com https://www.bothhandww.com Rev: A0 Page 5 of 7 Vin(nominal)：Nominal Input voltage 7. Load regulation : │Vout(FL)-Vout(NL)│ x100% Vout(FL) Vout(FL): Output voltage at full load Vout(NL): Output voltage at 25% full load or 10% full load 8. Ripple and Noise: as shown below. The bandwidth is 0-20MHz. Noise Ripple&Noise Ripple Output Ripple&Noise measurement test circuit: as shown below. Copper strip DC/DC converter Co Oscilloscope Load Copper strip Co: usually 0.47uF. E-mail: bothhand_sales@bothhandww.com https://www.bothhandww.com Rev: A0 Page 6 of 7 9. Temperature derating curve: The DC-DC converter will operate over a wider temperature range if less power Output Power (%) is drawn from the output and the device is already running. The temperature derating curve shows the operating power-temperature range. As shown below. 120 100 80 60 40 20 0 85 -40 -20 0 20 40 60 80 100 120 Ambient Temp.TA (℃) 10. Switching frequency: The nominal operating frequency of the DC-DC converters. 11. Input to output isolation: The dielectric breakdown strength test between input and output circuits. This is the isolation voltage the device is capable of withstanding for a specified time, usually 1 second or 1 minute. 12. Input souce impedance: The power module should be connected to low ac-impedance input souce. Highly inductive souce impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high , it maybe necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit , it is commended to use a good quality low Equivalent Series Resistance ( ESR < 0.1Ω at 100KHz ) capacitor of a 22uF for the power module. DC Power Supply Cin DC/DC converter E-mail: bothhand_sales@bothhandww.com Load https://www.bothhandww.com Rev: A0 Page 7 of 7