3
Features
Industrial / Sealed
n Compatible with surface mount
manufacturing processes
n Compatible with popular vacuum
pick-and-place equipment
n J-hook, gull-wing & pinned configurations
2.35
trimmer
(.092)
designs
(.090)
1.3
(.051)
2
PLCS.
mount
0.80 ± 0.10
2 PLCS.
information on lead
free surface
DIA.
trimmers
3.2
(.126)
n
For trimmer applications/processing
5.5
6.20
THRU.
(.216)
(.244)
guidelines, click here
n AEC-Q200 Qualified Grade 1
2.0
4.50
(.177)
2
PRODUCT TECHNICAL INVENTORY SAMPLES
SELECTOR LIBRARY
3314J-1, G-1, R-1, H-1
(Bourns 4.50
Marking,
Straight(.177)
Slot)
2.55
(.100)
CONTACT
Electrical Characteristics
Standard Resistance Range
���������������������� 10 ohms to 2 megohms
(see standard resistance table)
Resistance Tolerance�������������±20 % std.
(tighter tolerance available)
End Resistance�������1 % or 2 ohms max.
(whichever is greater)
Contact Resistance Variation
��������������������������������������3 % or 3 ohms
Resolution������������������������������������ Infinite
Insulation Resistance���������������� 500 vdc.
100 megohms min.
Dielectric Strength
Sea Level��������������� 500 vac (1 minute)
Adjustment Angle������������������ 210 ° nom.
3
3
1
2.3
(.091)
1.3
(.051)
2 PLCS.
0.8 ± 0.1
(.031 ± .004)
2 PLCS.
1.0
(.040)
3 PLCS.
5.00
(.197)
3314G-1
Power Rating (300 volts max. for Style G,
J & H; 50 volts max. for Style R)
4.00
(.157)
1.30 ± 0.1
(.051 ± .004)
5.00
(.197)
Environmental Characteristics
70 °C������������������������������������� 0.25 watt
125 °C���������������������������������������� 0 watt
Temperature Range���� -55 °C to +125 °C
Temperature Coefficient�����±100 ppm/°C
†
Seal Test���� 85 °C Fluorinert /60 seconds
Humidity����������������������������� 90-98 % RH,
10 cycles, 240 hours
TRS ±2 %; IR 10 megohms
Vibration������ 20 G TRS ±1 %; VRS ±1 %
Shock�������� 100 G TRS ±1 %; VRS ±1 %
Load Life
��� (@ 70 °C Rated Power 1000 Hours)
TRS ±3 %
Rotational Life������������������������100 cycles
TRS ±3 %
Thermal Shock��������������������������5 cycles
TRS ±2 %; VRS ±1 %
RECOMMENDED PCB
LAYOUT
2.35
(.093)
2.0
(.079)
3 PLCS.
2.55
(.100)
4.50
(.177)
2
4.50
(.177)
3314J-3, G-3, R-3, H-3
(Reverse
3 Marking,
1
Straight Slot)
3314J-2, G-2, R-2, H-2
(Bourns Marking,
± 0.10
Cross5.00
Slot)
3
.51 0.6 ± 0.1
WIDE
(.020)(.024 ± .004)
.51 3 PLCS. 3
DEEP
X
(.020)
X
3
1
3
1
2.35
(.093)
1
0.6
TYP.
(.024)
0.20
(.008)
TYP.
2
3
5.5
4.00
(.217)
(.157)
1.0
(.040)
1.3
3
PLCS.
(.051)
3 PLCS.
1.30 ± 0.1
(.051±±0.1
.004)
1.30
(.051 ± .004)
5.00
(.197)
5.00
(.197)
4.50
(.177)
2
.51
DEEP
X
(.020)
5.00
(.197)
2.0
(.079)
RECOMMENDED PCB
2.35
LAYOUT
RECOMMENDED PCB
(.093)
2.3
LAYOUT
(.091)
0.8 ± 0.1
1.3
2.3
0.1
(.0310.8
± ±.004)
(.051)
(.091)
(.031
± .004)
2 PLCS.
1.3
2 PLCS.
2 PLCS.
(.051)
2 PLCS.
6.20
5.00
(.244)
(.197)
TYP. COMMON(.157)
DIMENSIONS
ALL PIN STYLES:
CROSS
ADJ. SLOT
2.41 LONG
2.55
(.095)
(.100)
.51
WIDE
X
(.020)
0.80
(.031)
DIA. TYP.
0.20
(.008)
TYP.
5° MAX.
TYP.
1
2.0
(.079)
3 PLCS.
2.55
(.100)
2.0 2.0
(.079)
(.079)
3
COMMON DIMENSIONS ALL PIN STYLES:
STRAIGHT
ADJ. SLOT
2.45 LONG
(.096)
.51
WIDE
X
(.020)
.51
1
3
DEEP
X
(.020)
COMMON DIMENSIONS ALL PIN STYLES:
STRAIGHT
2
ADJ. SLOT
2.45 LONG
(.096)
.51
WIDE
X
(.020)
.51
3
1
DEEP
X
(.020)
2
2
COMMON DIMENSIONS ALL PIN STYLES:
CROSS
ADJ. SLOT
2.41 LONG
(.095)
.51
WIDE
X
(.020)
.51
1
DEEP
X
(.020)
COMMON DIMENSIONS ALL PIN STYLES:
CROSS
ADJ. SLOT
2.41 LONG
(.095)
.51
WIDE
X
(.020)
.51
1
DEEP
X
(.020)
MM
DIMENSIONS:
(INCHES)
0.30
TOLERANCES: ±
EXCEPT WHERE NOTED
(.012)
0.20
(.008)
TYP.
WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
4.50
0.6
*RoHS Directive 2015/863, Mar. 31, 2015 and Annex
TYP.
(.177)
(.024)
“Trimpot” is a trademark of Bourns, Inc. †“Fluorinert” is a registered trademark of 3M Co.
Specifications are subject to change without notice. Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on5°the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
MAX.
3
1
TYP.
RECOMMENDED PCB
REEL
13.0 ± 0.5
(.512 ± .02
DIA.
3314J-4, G-4, R-4, H-4
(Reverse Marking,
Cross
2.55 Slot)
4.00
COMMON DIMENSIONS - (.100)
ALL PIN STYLES:
STRAIGHT
2
2
ADJ. SLOT
2.452.55
LONG
(.100)
(.096)
2.55
(.100)
4.50
(.177)
12
(.4
1.3
(.051)
2 PLCS.
5.00
(.197)
4.50
(.177)
2
1.7
(.06
(.197 ± .004)
COMMON
DIMENSIONS COMMON DIMENSIONS 2
OUTSIDEALL
WHEN
ALL PIN STYLES:
PIN STYLES:
PINS ARE PARALLEL
STRAIGHT
CROSS
2
2
ADJ. SLOT
ADJ. SLOT
2.45 LONG6.30
2.41 LONG
(.248)
(.096)
(.095) 0.20
.51 4.50
.51 (.008)
WIDE
WIDE
X
X
(.020)(.177)
(.020) TYP.
.51
.51
1
3
1
DEEP
DEEP
X
X
(.020)
(.020)
0.20
(.008)
TYP.
4.50
(.177)
2.00
(.079
n RoHS compliant*
(.031- ±see
.004)processing
1.30 ± 0.10
3314 – 4 mm Square Trimpot® Trimming Potentiometer
(.079)
(.051 ± .004)
3314J-1
4.00
(.157
RECOMMENDED PCB
Product Dimensions
Click these links for more information:
(.059 + .0
LAYOUTstandard
n Meets EIA/EIAJ/IPC/VECI SMD
2.3
5.00
(.197)
Additional Information
R 0.13
(.005)
MAX.
TYP.
TYP. 0.20
(.008)
n Side adjust available
n Surface Mount / Single Turn / Cermet
1
* Emboss
** Emboss
(See Ho
Meets EIA
3314 – 4 mm Square Trimpot® Trimming Potentiometer
Physical Characteristics
Mechanical Angle������������������ 240 ° nom.
Torque����������������������������� 180 g-cm max.
Stop Strength������������������� 300 g-cm min.
Pushover Strength (S & Z Style)
�����������������1.6 kilograms (3.5 lbs.) min.
Weight���������������� Approximately 0.01 oz.
Marking������������������ Manufacturer’s code,
resistance code and date code
Wiper���������������� 50 % (Actual TR) ±10 %
Flammability���������������������������U.L. 94V-0
Standard Packaging
J, G and R���� 500 pcs./7 ˝ reel (MSL-1)
S and Z��������� 200 pcs./7 ˝ reel (MSL-1)
H������������������������������������� 100 pcs./tube
Adjustment Tool������������������������������� H-90
Storage Condition
...............40 °C max. / 70 % R.H. max.
Product Dimensions
5.00
(.197)
2
2.55
(.100)
6.20
(.244)
0.51 ± 0.13
(.020 ± .005)
TYP.
4.50
(.177)
3
TYP. 0.20
(.008)
0.80 ± 0.10
(.031 ± .004)
2 PLCS.
6.20
(.244)
1.30 ± 0.10
(.051 ± .004)
5.00
(.197)
4.50
(.177)
2
4.50
(.177)
R 0.13
(.005)
MAX.
TYP.
RECOMMENDED PCB
LAYOUT
2.3
(.090)
1.3
(.051)
2 PLCS.
DIA.
3.2
(.126)
THRU.
2.0
(.079)
1.3
(.051)
2 PLCS.
0.51 ± 0.12
.30
(.020 ± MAX.
.005)
(.012)
3 PLCS.
0.51 ± 0.13
5.50 ± 0.5
(.020 ± .005)
(.217 ± .020)
TYP.
DIA.
1.50 + 0.10/ - 0.00
(.059 + .004/ - .000)
34.00 ± 0.10
1
(.157 ± .004)
1.75 ± 0.10
(.069 ± .004)
12.00 ± 0.30
(.472 ± .012)
REEL
1
1.50 + 0.10
(.059 + .00
DIA.
4.00
(.157
0.27 ± 0.10
(.050 ± .004)
LEAD FOOTPRINT
2.0
(.079)
1.3
1.50
3 PLCS.
MIN.
EQUAL SPACED
3 PLCS.
(.051)
(.059)
20.2
MM
(.795)
13.0 ± 0.51 DIMENSIONS:
MIN. DIA.
(INCHES)
(.512 ± .020)
0.30
DIA.
TOLERANCES: ±
(.012)
18.4
(.724)
MAX.
(MEASURED
EXCEPT WHERE
NOTED
AT
HUB)
2.00
(.079
1.
(.0
REEL
13.0 ± 0.5
(.512 ± .02
DIA.
50.00
(1.969)
MIN.
0.20
(.008)
TYP.
2.55
(.100)
2.55
(.100)
0.6 ± 0.1
(.024 ± .004)
3 PLCS.
4.00
TYP.
(.157)
2.55
(.100)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
12.4 + 2.01/ -.000
(.488 + .079/ - .000)
(MEASURED AT HUB)
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart for further information.)
* Emboss
** Emboss
(See Ho
Meets EIA specification 481.
Meets EIA
5.00
(.197)
5.00
(.197)
3.5 ±
(.138 ±
RECOMMENDED PCB
5.26 ± 0.10
LAYOUT
2.31
(.207 ± .004)
(.091)
0.80 ± 0.10
1.3
(.031 ± .004)
(.051)
2 PLCS.
2 PLCS.
DIA.
8.00 ± 0.20
3.2
(.315 ± .008)
(.126)
6.25 DIA.
THRU(.246)
1.50 + 0.10/ - 0.00
HOLE
(.059 + .004/ - .000)
177.8 ± 2.03
DIA.*
(7.00 ± .080)
3
5.26 ± 0.10 (J)
(.2070.20
± .004)
R ± 0.10
6.45
(.008)
(G)
(.254MAX.
± .004)
4 PLCS.
5 ° MAX.
3 PLCS.
2.35 2.00 ± 0.05
(.079 ± .020)
(.093)
5.5
(.216)
5.00 ± 0.10
(.197 ± .004)
OUTSIDE WHEN
PINS ARE PARALLEL
6.30
(.248)
4.50
(.177)
TAPE
6.70
(.264)
2.74 ± 0.10
(.108 ± .004)
0.51 ± 0.13
(.020 ± .005)
TYP.
1
2.35
(.092)
5.00
TAPE (.197)
2
0.80
(.031)
DIA. TYP.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3314 – 4 mm Square Trimpot® Trimming Potentiometer
Product Dimensions
TAPE
2.54
(0.10)
1.27
(0.05)
1
2
1.42 ± 0.13
(0.056 ± 0.005)
5.61
(0.221)
1.05
(0.041)
0.50 ± 0.05
(.020 ± .002)
4.5
(0.177)
3
16.00 ± 0.3
(.630 ± 0.012)
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
7.50 ± 0.10
(.295 ± .004)
1.75 ± 0.10
(.069 ± .004)
0.61
(.024)
5.01
(.197)
3.30
(0.130)
1.78
(0.70)
0.50
(.020)
1
2
1.42 REF.
(.056)
4.95 ± 0.13
(0.193 ± 0.005)
3.13
(0.123)
5.81 ± 0.13
(0.229 ± 0.005)
R
1.5 + 0.1/-0.0
(0.59 +.004/-0.0)
DIA.
12.00 ± 0.10
(.472 ± .004)
4.00 ± 0.10
(.157 ± .004)
5.5
8.3
(.217) (.327)
2.00 ± 0.10
(.079 ± .004)
3
0.5
TYP.
(.020)
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
1.5
MIN.
(.059)
5.30 ± 0.10
(.209 ± .004)
7.30
(.287)
ORIENTATION
FEATURE
REEL
MIN.
RECOMMENDED PCB LAYOUT
3.5
(0.138)
1
2
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
1.2
(0.047)
DIA.
1.1
(0.043)
1.2
(0.047)
1.75
(0.069)
1.15
(0.045)
1.50
EQUAL SPACED 3 PLCS.
(.059)
20.2
(.795)
MIN. DIA.
13.0 ± 0.51
(.512 ± .020)
DIA.
22.4
(.882)
MAX.
(MEASURED
AT
HUB)
50.00
(1.969)
MIN.
5.8
(.228)
1.6
(0.063)
1
2
1.15
(0.045)
1.75
(0.069)
177.8 ± 2.03
DIA.*
(7.00 ± .080)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
MM
DIMENSIONS:
(INCHES)
0.30
TOLERANCES: ±
EXCEPT WHERE NOTED
(.012)
16.4 + 2.0/ -.000
(.646 + .079/ - .000)
(MEASURED AT HUB)
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart for further information.)
Meets EIA specification 481.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3314 – 4 mm Square Trimpot® Trimming Potentiometer
Product Dimensions
Packaging Specifications
5.00
(.197)
2
1.27
(0.50)
1
2
3
1
2
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
1.30 ± 0.100.21
(.051 ± .004)
(.008)
2
CLOCKWISE
0.30
TOLERANCES: ±
(.012)
5.00 ± 0.10
(.197 ± .004)
3 CW
OUTSIDE WHEN
PINS ARE PARALLEL
2
1
2.55
(.100)
0.6 ± 0.1
(.024 ± .004)
3 PLCS.
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
0.20
(.008)
TYP.
EXCEPT WHERE NOTED
2.55
(.100)
1
4.00
TYP.
(.157)
2.55
(.100)
5.00
(.197)
5.00
(.197)
7.5
(.295)
DIA.
1.50 + 0.10/
1.75- 0.00
(.059 + .004/
- .000)
(.069)
4.00 ± 0.10
(.157 ± .004)
1.50 + 0.10/-0.0
(0.59 +.004/-.0)
DIA.
2.00 ± 0.05
4.00 ± (.079
0.10 ± .020)
(.157 ± .004)
5.50 ± 0.5
(.217 ± .020)
5.26 ± 0.10 (J)
(.207 ± .004)
6.45 ± 0.10
(G)
(.254 ± .004)
3.5 ±
(.138 ±
1.50 + 0.10
(.059 + .004
DIA.
4.00
(.157
12.00
(.472) 5.26 ± 0.10
(.207 ± .004)
2.00
(.079
5.50 ± 0.10
(.217 ± .004)
2.00 ± 0.10
(.079 ± .004)
8.00 ± 0.20
(.315 ± .008)
1.75 ± 0.10
(.069 ± .004)
5.50±±0.30
0.10
12.00
(.217±±.012)
.004)
(.472
DIA.
1.50 + 0.10/ - 0.00
1.50
(.059
+ .004/
DIA.
MIN.- .000)
(.059)
1.7
(.06
REEL
REEL
1.50
EQUAL SPACED 3 PLCS.
(.059)
5.59 ± 0.10
20.2(.220 ± .004)
18.4
(.795)
REEL
13.0 ± 0.51
(.724)
MIN. DIA.
(.512 ± .020) 1.50
MAX.
DIA. MIN. (.059) EQUAL SPACED 3 PLCS.
(MEASURED
AT
20.2
HUB)
22.4
(.795)
13.0 ± 0.51
(.882)
MIN. DIA.
(.512 ± .020)
50.00
MAX.
DIA.
(1.969)
(MEASURED
MIN.
AT
HUB)
MIN.
WIPER
6.30
(.248)
4.50 MM
DIMENSIONS:
(INCHES)
(.177)
3
2.0
(.079)
1.3
2.01
(.051)
(.079)
2 PLCS.
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
16.00
(.630)
5 ° MAX.
4.50
(.177)
CCW 1
2
2
R 0.13
(.005)
MAX.
TYP.
TYP. 0.20 5.56
(.008)
(0.219)
0.96
3.08
(.038)
(0.121)
3.18
RECOMMENDED PCB
(.125)
5.76
LAYOUT
(0.227)
2.3
2.35
(.090)
(.092)
0.80 ± 0.10
1.3
(.031 ± .004)
(.051)
RECOMMENDED PCB LAYOUT
2 PLCS.
2 PLCS.
2.54
DIA.
(0.10)
3.2
1.3
2.01
(.126)
5.5
(.079)
6.20 (0.051)
THRU.
0.26
(.216)
(.244)
(.010)
5.00
(.197)2.01
(.079)
1
0.51 ± 0.13
(.020 ± .005)
TYP.
3.48
(.137)
TAPE
.30 MAX.
(.012)
2.74 ± 0.10
(.108 ± .004)
0.61
(.024)
5.01
(.197)
1
TAPE
TAPE
0.40
MAX.
(.016)
3.32
0.51 ± 0.13
(.020 ± (0.131)
.005)
TYP.
4.50
(.177)
1.29
(0.051)
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
2.55
(.100)
2.54
6.20
(0.10)
(.244)
1.19
(0.047)
177.8 ± 2.03
DIA.*
(7.00 ± .080)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
13.0 ± 0.51
(.512 ± .020
DIA.
50.00
(1.969)
MIN.
12.4 + 2.01/ -.000
(.488 + .079/ - .000)
(MEASURED AT HUB)
177.8 ± 2.03
DIA.*
.080)
* Embossed(7.00
Tape±Designator
"E"
16.4 + 2.0/ -.000
** Embossed 330.2
Tape Designator
"G"
± 2.0
(.646 + .079/ - .000)
DIA.**
(See How(13.00
To Order
chart for further information.)
± .079)
(MEASURED AT HUB)
Meets EIA specification 481.
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart for further information.)
Meets EIA specification 481.
0.80
(.031)
DIA. TYP.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
* Emboss
** Emboss
(See Ho
Meets EIA s
3314 – 4 mm Square Trimpot® Trimming Potentiometer
Packaging Specifications
TAPE
)
TAPE
MAX.
5
20)
± 0.10 (J)
± .004)
± 0.10
(G)
± .004)
0.25 ± 0.10
(.010 ± .004)
3.5 ± 0.10
(.138 ± .004)
6°±2°
1
2
5.52 ± 0.05
(.217 ± .002)
3
ROTOR POSITIONED AS SHOWN
1.50 + 0.10/ - 0.00
WITHIN ± 22 ° OF CENTERLINE
(.059 + .004 - .00)
6.48 ± 0.10
OF TERMINAL 2
DIA.
(.255 ± .004)
4.00 ± 0.10
(.157 ± .004)
26 ± 0.10
07 ± .004)
5.26 ± 0.10
(.207 ± .004)
2.00 ± 0.05
(.079 ± .002)
1.50 + 0.10/ - 0.00
(.059 + .004 - .000)
DIA.
00 ± 0.20
15 ± .008)
DIA.
10/ - 0.00
04/ - .000)
1
2
2.54
(0.10)
1.27
(0.05)
0.3
1.05
(.012)
(0.041)
50.00
(1.969)
MIN.
01/ -.000
9/ - .000)
D AT HUB)
1.50
EQUAL SPACED 3 PLCS.
(.059)
20.2
(.795)
MIN. DIA.
13.0 ± 0.51
(.512 ± .020)
DIA.
1
2
0.50 ± 0.05
(.020 ± .002)
4.5
(0.177)
16.00 ± 0.3
(.630 ± 0.012)
DIA.
1.5
(.059)
7.50 ± 0.10
(.295 ± .004)
4.00
(.157)
1.75 ± 0.10
(.069 ± .004)
0.61
(.024)
5.01
2.00
(.197)
(.079)
1.42 REF.
(.056)
4.95 ± 0.13
(0.193 ± 0.005)
8.00
3.13
(.315)
(0.123)
3.30
(0.130)
5.81 ± 0.13
(0.229 ± 0.005)
1.78
(0.70)
0.50
(.020)
1.75
(.069)
16.00
(.630)
REEL
18.4
(.724)
MAX.
MEASURED
AT
HUB)
0.33
5.61
(.013)
(0.221)
3
ROTOR POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
177.8 ± 2.03
DIA.*
(7.00 ± .080)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
50.00
(1.969)
MIN.
5.5
8.3
(.217) (.327)
2.00 ± 0.10
(.079 ± .004)
7.5
(.295)
1.5
MIN.
(.059)
5.30 ± 0.10
(.209 ± .004)
DIA.
7.30
(.287)
LABEL
REEL
MIN.
RECOMMENDED PCB LAYOUT
3.5
(0.138)
1.2
(0.047)
0.5
TYP.
(.020)
12.00 ± 0.10
(.472 ± .004)
4.00 ± 0.10
(.157 ± .004)
ORIENTATION
FEATURE
18.4
(.724)
MAX.
(MEASURED
AT
HUB)
R
1.5 + 0.1/-0.0
(0.59 +.004/-0.0)
DIA.
3
1.75 ± 0.10
ROTOR POSITIONED AS SHOWN
(.068 ± .004)
12.00 ± 0.30
WITHIN ± 22 ° OF CENTERLINE
(4.72 ± .012)
OF TERMINAL 2
MIN.
TAPE
0.22
2 PLCS.
(.009)
1.42 ± 3.5
0.13
(0.056 ±(.138)
0.005)
1.1
(0.043)
1.2
(0.047)
1.75
178.0
(0.069)
DIA.
(7.00)
1.15
(0.045)
1.50
EQUAL SPACED 3 PLCS.
(.059)
20.2
(.795)
MIN. DIA.
13.0 ± 0.51
(.512 ± .020)
DIA.
22.4
(.882)
MAX.
(MEASURED
AT
HUB)
50.00
(1.969)
MIN.
5.8
12.4 + 2.01/ -.000
(.488 + .079/ - .000)
(MEASURED AT HUB)
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart
information.)
1 for
2 further
3
Meets EIA specification
ROTOR481.
POSITIONED AS SHOWN
WITHIN ± 22 ° OF CENTERLINE
OF TERMINAL 2
(.228)
MM
DIMENSIONS:
(INCHES)
0.30
1.15
TOLERANCES: ±
EXCEPT
WHERE NOTED
(.012)
(0.045)
1.6
(0.063)
1.75
(0.069)
177.8 ± 2.03
DIA.*
(7.00 ± .080)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
16.4 + 2.0/ -.000
(.646 + .079/ - .000)
(MEASURED AT HUB)
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart for further information.)
Meets EIA specification 481.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
6
9)
3314 – 4 mm Square Trimpot® Trimming Potentiometer
Packaging Specifications
How To Order
Standard Resistance Table
3314 J - 1 - 502 E
TAPE
0.40
MAX.
(.016)
16.00
(.630)
7.5
(.295)
1.75
(.069)
0.96
(.038)
1.50 + 0.10/-0.0
(0.59 +.004/-.0)
DIA.
12.00
(.472)
4.00 ± 0.10
(.157 ± .004)
5.50 ± 0.10
(.217 ± .004)
2.00 ± 0.10
(.079 ± .004)
0.26
010)
DIA.
5.50 ± 0.10
(.217 ± .004)
1.50
MIN.
(.059)
5 ° MAX.
1
9)
5.59 ± 0.10
(.220 ± .004)
REEL
MIN.
1.50
EQUAL SPACED 3 PLCS.
(.059)
20.2
(.795)
MIN. DIA.
13.0 ± 0.51
(.512 ± .020)
DIA.
Model
Style
Standard or Modified Product
Indicator (Styles J, G, H & S)
-1 = Single Slot
-2 = Cross Slot
-3 = Single Slot w/Reverse Marking
-4 = Cross Slot w/Reverse Marking
Product Indicator (Style R only)
-GM5 = Cross Slot w/Extended
Lead Frame
-1 = Single Slot
-2 = Cross Slot
-3 = Single Slot w/Reverse Marking
-4 = Cross Slot w/Reverse Marking
Product Indicator (Style Z only)
-GA4 = Single Slot
-1 = Cross Slot
-3 = Single Slot w/Reverse Marking
-4 = Cross Slot w/Reverse Marking
Resistance Code
Embossed Tape Designator (MSL-1)**
E = Styles J, G and R: 500 pcs. / 7 ˝ reel
Styles S and Z: 200 pcs. / 7 ˝ reel
G = Styles J and G: 3000 pcs. / 13 ˝ reel
Style R: 2500 pcs. / 13 ˝ reel
Styles S and Z: 1000 pcs. / 13 ˝ reel
**Style H is available in tube packaging only.
Resistance Resistance
(Ohms)
Code
10
100
20
200
50
500
100 101
200
201
500
501
1,000
102
2,000
202
5,000
502
10,000
103
20,000
203
50,000
503
100,000
104
200,000
204
250,000
254
500,000
504
1,000,000
105
2,000,000
205
Popular distribution values listed in boldface.
Special resistances available.
Tape and reel material meets Antistatic ANSI/
ESD 5541-2003 packaging standards.
22.4
(.882)
MAX.
(MEASURED
AT
HUB)
50.00
(1.969)
MIN.
177.8 ± 2.03
DIA.*
(7.00 ± .080)
330.2 ± 2.0
DIA.**
(13.00 ± .079)
16.4 + 2.0/ -.000
(.646 + .079/ - .000)
(MEASURED AT HUB)
* Embossed Tape Designator "E"
** Embossed Tape Designator "G"
(See How To Order chart for further information.)
Meets EIA specification 481.
Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
MM
DIMENSIONS:
(INCHES)
0.30
TOLERANCES: ±
EXCEPT WHERE NOTED
(.012)
REV. 07/23
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and its
affiliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information and verify that such information is current and
complete before placing orders for Bourns® products.
The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary
from the data sheet characteristics and parameters due to (i) the combination of the Bourns® product with other components
in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns®
product also can and do vary in different applications and actual performance may vary over time. Users should always verify
the actual performance of the Bourns® product in their specific devices and applications, and make their own independent
judgments regarding the amount of additional test margin to design into their device or application to compensate for
differences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns® product to meet the requirements of such industry standard or particular qualification. Users of
Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to their
devices or applications.
Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or
environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives on a
case-by-case basis, use of any Bourns® products in such unauthorized applications might not be safe and thus is at the user’s
sole risk. Life-critical applications include devices identified by the U.S. Food and Drug Administration as Class III devices and
generally equivalent classifications outside of the United States.
Bourns expressly identifies those Bourns® standard products that are suitable for use in automotive applications on such
products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive
application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns
expressly identifies a sub-category of automotive application in the data sheet for its standard products (such as infotainment
or lighting), such identification means that Bourns has reviewed its standard product and has determined that if such Bourns®
standard product is considered for potential use in automotive applications, it should only be used in such sub-category of
automotive applications. Any reference to Bourns® standard product in the data sheet as compliant with the AEC-Q standard
or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application.
Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns expressly identifies Bourns® standard products that are suitable for use in aircraft
or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically
approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard
product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at the
user’s sole risk.
The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns and
the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns and the
user regarding the use and level of such testing, the above provisions applicable to Bourns® standard products shall also apply
to such Bourns® custom products.
Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns® products and Bourns technology and technical data may not under any circumstance be
exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without prior
authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible
to receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential,
incidental or indirect damages or lost revenues or lost profits, and (ii) any and all implied warranties, including implied warranties
of fitness for particular purpose, non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese
bilingual versions are available at:
Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies
PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf
C1753 05/17/18R
工商网监
湘ICP备2023018690号
