Features
n Small diameter
n Wide resistance range
n Good resolution
n Linear tapers
n Cermet element
3862 – 1/2 ˝ Diameter Single-Turn Panel Control
Initial Electrical Characteristics1
Standard Resistance Range������������������������������������������������������������������������������������������������������������������������������������������������ 1K ohms to 1 megohm
Total Resistance Tolerance��������������������������������������������������������������������������������������������������������������������������������������������������������������(A Taper) ±10 %
.
(H Taper) ±5%
Independent Linearity��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� ±5 %
Absolute Minimum Resistance�����������������������������������������������������������������������������������������������������������������������������������������������������2 ohms maximum
Effective Electrical Angle������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 260 ° ±10 °
Contact Resistance Variation�����������������������������������������������������������������������������������������������������������������������±3 % or 6 ohms (whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������750 VAC minimum
70,000 Feet���������������������������������������������������������������������������������������������������������������������������������������������������������������������������350 VAC minimum
Insulation Resistance (500 VDC)������������������������������������������������������������������������������������������������������������������������������������1,000 megohms minimum
Power Rating (Voltage Limited by Power Dissipation or 350 VAC, Whichever is Less)
+70 °C��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������1 watt
+125 °C������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������0 watt
Theoretical Resolution������������������������������������������������������������������������������������������������������������������������������������������������������������������Essentially infinite
Environmental Characteristics1
Operating Temperature Range�����������������������������������������������������������������������������������������������������������������������������������������������������-40 °C to +125 °C
Storage Temperature Range��������������������������������������������������������������������������������������������������������������������������������������������������������-65 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range��������������������������������������������������������������������������������������������������������������� ±150 ppm/°C
Vibration ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 20 G
Total Resistance Shift�����������������������������������������������������������������������������������������������������������������������������������������������������������������±2 % maximum
Voltage Ratio Shift����������������������������������������������������������������������������������������������������������������������������������������������������������������������±6 % maximum
Shock��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 50 G
Total Resistance Shift�����������������������������������������������������������������������������������������������������������������������������������������������������������������±2 % maximum
Voltage Ratio Shift����������������������������������������������������������������������������������������������������������������������������������������������������������������������±6 % maximum
Load Life������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������ 1,000 hours
Total Resistance Shift�����������������������������������������������������������������������������������������������������������������������������������������������������������������±3 % maximum
Rotational Life, No Load
(C & N Bushings)�������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 50,000 cycles
(E & T Bushings)����������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 1,000 cycles
Total Resistance Shift������������������������������������������������������������������������������������������������������������������������������������������������������������±5 % maximum
Contact Resistance Variation�������������������������������������������������������������������������������������������������������������±3 % or 6 ohms (whichever is greater)
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Total Resistance Shift�����������������������������������������������������������������������������������������������������������������������������������������������������������������±2 % maximum
Insulation Resistance (500 VDC)���������������������������������������������������������������������������������������������������������������������������������100 megohms minimum
Salt Spray�������������������������������������������������������������������������������������������������������������������������������������������������� MIL-STD-202, Method 101, Condition A
IP Rating�����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������IP 40
Mechanical Characteristics1
Stop Strength��������������������������������������������������������������������������������������������������������������������������������������������������������������33 N-cm (3 lb.-in.) maximum
Mechanical Angle������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 295 ° ±3 °
Torque
Starting and Running�����������������������������������������������������������������������������������������������������������������������������������������3.53 N-cm (5 oz.-in.) maximum
Mounting (Torque on Bushing)����������������������������������������������������������������������������������������������������������������� 1.7-2.0 N-m (15-18 lb.-in.) maximum
Shaft Locking Torque with Locking Bushings���������������������������������������������������������������������������������������������������������������� 14.12 N-cm (20 oz.-in.)
Weight (Single Section)�������������������������������������������������������������������������������������������������������������������������������������������������������������25 grams maximum
Terminals������������������������������������������������������������������������������������������������������������������������������������������������������������������ Printed circuit pins or J-Hooks
Soldering Condition����������������������������������������������������Recommended hand soldering using Sn85/Ag5 no clean solder, 0.025 ˝ wire diameter
.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
.
Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.
Marking���������������������������������������������������������������� Manufacturer’s trademark, wiring diagram, date code, resistance, manufacturer’s part number
Ganging�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������1 cup maximum
Hardware�������������������������������������������������������������� One lockwasher (H-37-1) and one mounting nut (H-38-1) is shipped with each potentiometer;
locking bushing versions are shipped with one additional locking nut (H-38-3).
1 ELECTRICAL SPECIFICATIONS TESTED AT 250 RPM, AT ROOM AMBIENT: +25 °C NOMINAL.
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice. Users should verify actual device performance in their specific
applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3862 – 1/2 ˝ Diameter Single-Turn Panel Control
Product Dimensions
PCB LAYOUT
5.08
(.200)
PANEL LAYOUT
6.325
(.249)
3.04
(.120)
45 °
2.54
(.100)
TYP.
6.325
(.249)
5.08
(.200)
3862E/T
6.731
(.265)
DIA.
15.88
3862C/N
STD.
(5/8)
.89 ± .25
11.51 ± .41
3.18 ± .03
(.035 ± .010)
(.453 ± .016)
DIA.
2 PLCS. (.125 ± .001)
12.07 ± .76
L
.79 (.475 ± .030)
(.031)
11.51 ± .41
(.453 ± .016)
12.07 ± .76
(.475 ± .030)
12.7 ± .41
DIA.
(.500 ± .016)
2.438 + .127 / -0.000
(.096 + .005 / - .000)
DIA. 2 PLCS.
Shaft End Detail
3862
9.53, 22.23
STD.
(3/8, 7/8)
.89 ± .25
3.18 ± .03
(.035 ± .010)
DIA.
(.125 ± .001)
2 PLCS.
L
.79
2.38
(.031)
(.094)
DIA. 12.7 ± .41
(.500 ± .016)
45 ° ± 15 °
.41
.41
45 ° ± 5 ° X
6.25
(.016)
(.016) 6.25
-32 UNEF - 2A
-32 UNEF - 2A
(1/4)
6.35
3.3
.79 ± .25
(1/4)
.79 ± .25
POSITION OF SLOTS VARIABLE
OPTIONAL FLAT
LONG OR
(.250)
(.13) 16.88(.031 ± .010)
(.031 ± .010)
9.53
12.7
FOR "T" BUSHING,
FOR "E" BUSHING
L =
FROM BUSHING FOR SHAFTS UNDER
(.375)
(.500)
(5/8)
6.35
9.65
L =
FOR "C" BUSHING,
FOR "N" BUSHING
(.250)
(.380)
45 ° ± 5 ° X
PC PIN TERMINAL
3.04
(.12)
3
2.54
(0.10)
5.08
(0.20)
6.22
(.245)
2 PLCS.
.723
(.0285)
32-1/2 ° ± 10 °
FLAT ORIENTATION
@ CCW END
SLOTS ARE
NOT ORIENTED
C OF LUG
L
1
3
2
2
1
5.08
(.20)
.25
(.010)
2 PLCS.
CCW
2.286
(.09)
TYP.
4.953
REF ONLY
(.195)
12.06 ± .762
(.475 ± .03)
2
3
J-HOOK TERMINAL
2.31
2 PLCS.
(.091)
POTENTIOMETER
.762
(.03)
TYP.
1
8.89
(.35)
5.08
(0.20)
2.54
(0.10)
6.53
(.250)
MAX.
MM
(INCHES)
DIMENSIONS:
Hardware
LOCKWASHER H-37-1
NUT H-38-1
6.6
(.26)
LOCKING NUT H-38-3
9.53 +0/-0.38
(.375 +0/-.015)
2.36 ± 0.25
(.093 ± .01)
1/4-32 UNEF
12.07 ± 0.25
(.475 ± .01)
0.64 ± 0.05
(.025 ± .002)
M = COUNTRY OF MANUFACTURE
(MEXICO)
YY = LAST TWO DIGITS OF YEAR
MANUFACTURED
30 ° ± 5 °
TYP.
11 +0/-0.43
(.433 +0/-.017)
DIMENSIONS:
WW = WEEK NUMBER
15 ° ± 1 °
7.75
(.305)
Date Code Description
YYWWM
4.57 ± 0.05
(.180 ± .002)
MM
(INCHES)
1/4-32
NEF-20
0.64
(.025)
7.92
(.312)
30 ° ± 5 °
1.02
(.040)
3.96
(.156)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
How to Order 3862 Series Panel Controls
3862
12
16
20
28
C
-
28
2
SHAFT TYPE
(FMS) & DIAMETER
3/8 ” (9.53 mm) L X 1/8 ” (3.18 mm) D
1/2 ” (12.7 mm) L x 1/8 ” (3.18 mm) D
5/8 ” (15.88 mm) L x 1/8 ” (3.18 mm) D
7/8 ” (22.20 mm) L X 1/8 ” (3.18 mm) D
-
102
A
BUSHINGS
C
C
C, E, N, T
C, E, N, T
Consult factory for lengths not shown.
C
E
N
T
BUSHING
Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L
Plain 1/4 ” (6.35 mm) D x 3/8 ” (9.53 mm) L
Locking 1/4 ” (6.35 mm) D x 3/8 ” (9.53 mm) L
MODEL
3862 1/2 ” (12.7 mm) D Single-Turn Cermet
1
2
3
5
6
7
L
RESISTANCE
CODE/VALUE
(IN OHMS)
(102)
(252)
(502)
(103)
(253)
(503)
(104)
(254)
(504)
(105)
1K
2.5K
5K
10K
25K
50K
100K
250K
500K
1M
RoHS IDENTIFIER
L
Compliant
ELEMENT
TAPER/TOLERANCE
A
H
Linear ±10 %
Linear ±5 %
TERMINAL STYLE AND
SHAFT TYPE
Solder Lugs, Plain End
Solder Lugs, Slotted End
Solder Lugs, Flatted Shaft
PC Pins, Plain End
PC Pins, Slotted End
PC Pins, Flatted End
Boldface features are Bourns standard
options. All others are available with higher
minimum order quantities.
Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
REV. 10/20
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and
P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹
Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change
^P[OV\[UV[PJL
很抱歉,暂时无法提供与“3862C-202-502AL”相匹配的价格&库存,您可以联系我们找货
免费人工找货- 国内价格
- 15+86.30558
- 30+84.70957
- 国内价格 香港价格
- 1+219.268601+28.38204
- 10+182.0019210+23.55826
- 25+168.8774825+21.85943
- 50+159.5509750+20.65221
- 100+150.71453100+19.50843
- 250+139.75824250+18.09025
- 500+131.98955500+17.08468