BD239B

BD239, BD239A, BD239B, BD239C NPN SILICON POWER TRANSISTORS ● ● ● ● ● Designed for Complementary Use with the BD240 Series 30 W at 25°C Case Temperature 2 A Continuous Collector Current 4 A Peak Collector Current Customer-Specified Selections Available B C E TO-220 PACKAGE (TOP VIEW) 1 2 3 Pin 2 is in electrical contact with the mounting base. MDTRACA absolute maximum ratings at 25°C case temperature (unless otherwise noted) RATING BD239 Collector-emitter voltage (RBE = 100 Ω) BD239A BD239B BD239C BD239 Collector-emitter voltage (IC = 30 mA) BD239A BD239B BD239C Emitter-base voltage Continuous collector current Peak collector current (see Note 1) Continuous base current Continuous device dissipation at (or below) 25°C case temperature (see Note 2) Continuous device dissipation at (or below) 25°C free air temperature (see Note 3) Unclamped inductive load energy (see Note 4) Operating junction temperature range Storage temperature range Lead temperature 3.2 mm from case for 10 seconds NOTES: 1. 2. 3. 4. VEBO IC ICM IB Ptot Ptot ½LIC2 Tj Tstg TL V CEO VCER SYMBOL VALUE 55 70 90 115 45 60 80 100 5 2 4 0.6 30 2 32 -65 to +150 -65 to +150 250 V A A A W W mJ °C °C °C V V UNIT This value applies for tp ≤ 0.3 ms, duty cycle ≤ 10%. Derate linearly to 150°C case temperature at the rate of 0.24 W/°C. Derate linearly to 150°C free air temperature at the rate of 16 mW/°C. This rating is based on the capability of the transistor to operate safely in a circuit of: L = 20 mH, IB(on) = 0.4 A, RBE = 100 Ω, VBE(off) = 0, RS = 0.1 Ω, VCC = 20 V. JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 1 BD239, BD239A, BD239B, BD239C NPN SILICON POWER TRANSISTORS electrical characteristics at 25°C case temperature PARAMETER Collector-emitter breakdown voltage TEST CONDITIONS BD239 V(BR)CEO IC = 30 mA (see Note 5) VCE = 55 V ICES Collector-emitter cut-off current Collector cut-off current Emitter cut-off current Forward current transfer ratio Collector-emitter saturation voltage Base-emitter voltage Small signal forward current transfer ratio Small signal forward current transfer ratio VCE = 70 V VCE = 90 V VCE = 115 V ICEO IEBO hFE V CE(sat) VBE hfe VCE = 30 V VCE = 60 V VEB = VCE = VCE = IB = VCE = 5V 4V 4V 0.2 A 4V VBE = 0 VBE = 0 VBE = 0 VBE = 0 IB = 0 IB = 0 IC = 0 IC = 0.2 A IC = IC = IC = 1A 1A 1A (see Notes 5 and 6) (see Notes 5 and 6) (see Notes 5 and 6) f = 1 kHz f = 1 MHz 20 3 40 15 0.7 1.3 V V IB = 0 BD239A BD239B BD239C BD239 BD239A BD239B BD239C BD239/239A BD239B/239C MIN 45 60 80 100 0.2 0.2 0.2 0.2 0.3 0.3 1 mA µA mA V TYP MAX UNIT VCE = 10 V VCE = 10 V IC = 0.2 A IC = 0.2 A |hfe | NOTES: 5. These parameters must be measured using pulse techniques, tp = 300 µs, duty cycle ≤ 2%. 6. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts. thermal characteristics PARAMETER RθJC RθJA Junction to case thermal resistance Junction to free air thermal resistance MIN TYP MAX 4.17 62.5 UNIT °C/W °C/W resistive-load-switching characteristics at 25°C case temperature PARAMETER ton toff † TEST CONDITIONS IC = 200 mA VBE(off) = -3.4 V IB(on) = 20 mA RL = 150 Ω † MIN IB(off) = -20 mA tp = 20 µs, dc ≤ 2% TYP 0.3 0.8 MAX UNIT µs µs Turn-on time Turn-off time Voltage and current values shown are nominal; exact values vary slightly with transistor parameters. 2 JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP BD239, BD239A, BD239B, BD239C NPN SILICON POWER TRANSISTORS TYPICAL CHARACTERISTICS TYPICAL DC CURRENT GAIN vs COLLECTOR CURRENT 1000 VCE = 4 V tp = 300 µs, duty cycle < 2% TCS631AG COLLECTOR-EMITTER SATURATION VOLTAGE vs BASE CURRENT VCE(sat) - Collector-Emitter Saturation Voltage - V 10 TCS631AE TC = 25°C TC = 80°C IC = 100 mA IC = 300 mA IC = 1 A hFE - DC Current Gain 1·0 100 0·1 10 0·01 0·1 IC - Collector Current - A 1·0 0·01 0·1 1·0 10 100 1000 IB - Base Current - mA Figure 1. Figure 2. BASE-EMITTER VOLTAGE vs COLLECTOR CURRENT 1·0 VCE = 4 V TC = 25°C VBE - Base-Emitter Voltage - V 0·9 TCS631AF 0·8 0·7 0·6 0·5 0·01 0·1 IC - Collector Current - A 1·0 Figure 3. JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 3 BD239, BD239A, BD239B, BD239C NPN SILICON POWER TRANSISTORS MAXIMUM SAFE OPERATING REGIONS MAXIMUM FORWARD-BIAS SAFE OPERATING AREA 100 SAS631AE IC - Collector Current - A 10 tp = 300 µs, d = 0.1 = 10% tp = 1 ms, d = 0.1 = 10% tp = 10 ms, d = 0.1 = 10% DC Operation 1·0 0·1 BD239 BD239A BD239B BD239C 10 100 1000 0·01 1·0 VCE - Collector-Emitter Voltage - V Figure 4. THERMAL INFORMATION MAXIMUM POWER DISSIPATION vs CASE TEMPERATURE 40 Ptot - Maximum Power Dissipation - W TIS631AB 30 20 10 0 0 25 50 75 100 125 150 TC - Case Temperature - °C Figure 5. 4 JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP BD239, BD239A, BD239B, BD239C NPN SILICON POWER TRANSISTORS MECHANICAL DATA TO-220 3-pin plastic flange-mount package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. TO220 4,70 4,20 ø 3,96 3,71 10,4 10,0 2,95 2,54 6,6 6,0 15,90 14,55 1,32 1,23 see Note B see Note C 6,1 3,5 0,97 0,61 1 2 3 1,70 1,07 14,1 12,7 2,74 2,34 5,28 4,88 2,90 2,40 0,64 0,41 VERSION 1 VERSION 2 ALL LINEAR DIMENSIONS IN MILLIMETERS NOTES: A. The centre pin is in electrical contact with the mounting tab. B. Mounting tab corner profile according to package version. C. Typical fixing hole centre stand off height according to package version. Version 1, 18.0 mm. Version 2, 17.6 mm. MDXXBE JUNE 1973 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 5