BUL791

BUL791 NPN SILICON POWER TRANSISTOR ● ● ● ● ● Designed Specifically for High Frequency Electronic Ballasts up to 125 W hFE 6 to 22 at VCE = 1 V, IC = 2 A Low Power Losses (On-state and Switching) Key Parameters Characterised at High Temperature Tight and Reproducible Parametric Distributions B C E TO-220 PACKAGE (TOP VIEW) 1 2 3 Pin 2 is in electrical contact with the mounting base. MDTRACA absolute maximum ratings at 25°C ambient temperature (unless otherwise noted ) RATING Collector-emitter voltage (VBE = 0) Collector-base voltage (IE = 0) Collector-emitter voltage (IB = 0) Emitter-base voltage Continuous collector current Peak collector current (see Note 1) Peak collector current (see Note 2) Continuous base current Peak base current (see Note 2) Continuous device dissipation at (or below) 25°C case temperature Operating junction temperature range Storage temperature range NOTES: 1. This value applies for tp = 10 ms, duty cycle ≤ 2%. 2. This value applies for tp = 300 µs, duty cycle ≤ 2%. SYMBOL VCES VCBO V CEO VEBO IC ICM ICM IB IBM Ptot Tj Tstg VALUE 700 700 400 9 4 8 14 2.5 3.5 75 -65 to +150 -65 to +150 UNIT V V V V A A A A A W °C °C JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 1 BUL791 NPN SILICON POWER TRANSISTOR electrical characteristics at 25°C case temperature (unless otherwise noted) PARAMETER V CEO(sus) ICES IEBO V BE(sat) VCE(sat) Collector-emitter sustaining voltage Collector-emitter cut-off current Emitter cut-off current Base-emitter saturation voltage Collector-emitter saturation voltage Forward current transfer ratio Collector-base forward bias diode voltage IC = 100 mA VCE = 700 V VCE = 700 V VEB = 9V TEST CONDITIONS L = 25 mH VBE = 0 VBE = 0 IC = 0 IC = IC = IC = IC = IC = IC = 2A 2A 2A 2A 2A 8A (see Notes 4 and 5) TC = 90°C (see Notes 4 and 5) TC = 90°C 10 6 2 0.94 0.86 0.25 0.3 16.5 12 6.5 850 22 14 mV 0.4 TC = 90°C (see Note 3) MIN 400 10 200 1 1 TYP MAX UNIT V µA mA V V IB = 400 mA IB = 400 mA IB = 400 mA IB = 400 mA VCE = VCE = VCE = 1V 1V 5V IC = 10 mA hFE VFCB ICB = 60 mA NOTES: 3. Inductive loop switching measurement. 4. These parameters must be measured using pulse techniques, tp = 300 µs, duty cycle ≤ 2%. 5. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts, and located within 3.2 mm from the device body. thermal characteristics PARAMETER R θJA R θJC Junction to free air thermal resistance Junction to case thermal resistance MIN TYP MAX 62.5 1.66 UNIT °C/W °C/W inductive-load switching characteristics at 25°C case temperature PARAMETER tsv tfi txo tsv tfi Storage time Current fall time Cross over time Storage time Current fall time IC = 2 A L = 1 mH IC = 2 A L = 1 mH TEST CONDITIONS IB(on) = 400 mA IB(off) = 800 mA IB(on) = 400 mA IB(off) = 250 mA VCC = 40 V VCLAMP = 300 V VCC = 40 V VCLAMP = 300 V MIN TYP 2.2 95 210 4 120 MAX 3 180 300 6 230 UNIT µs ns ns µs ns resistive-load switching characteristics at 25°C case temperature PARAMETER tsv tfi Storage time Current fall time IC = 2 A VCC = 300 V TEST CONDITIONS IB(on) = 400 mA IB(off) = 400 mA MIN TYP 2.2 160 MAX 3 250 UNIT µs ns 2 JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP BUL791 NPN SILICON POWER TRANSISTOR TYPICAL CHARACTERISTICS FORWARD CURRENT TRANSFER RATIO vs COLLECTOR CURRENT TC = 25°C hFE - Forward Current Transfer Ratio VCE(sat) - Collector-Emitter Saturation Voltage - V 30 L791CHF COLLECTOR-EMITTER SATURATION VOLTAGE vs COLLECTOR CURRENT 10 IB = I C / 5 TC = 25°C TC = 90°C L791CVB 10 1·0 0·1 VCE = 1 V V CE = 5 V 1·0 0·01 0·1 1·0 10 20 0·01 0·1 1·0 IC - Collector Current - A 10 IC - Collector Current - A Figure 1. Figure 2. INDUCTIVE SWITCHING TIMES vs COLLECTOR CURRENT 10 IB(on) = IC / 5 IB(off) = IC / 2.5 VCC = 40 V VCLAMP = 300 V L = 1 mH TC = 25°C L791CI1 INDUCTIVE SWITCHING TIMES vs CASE TEMPERATURE 10 L791CI3 Inductive Switching Time - µs 1·0 Inductive Switching Time - µs tsv txo tfi IB(on) = 400 mA, VCC = 40 V, L = 1 mH IB(off) = 800 mA, VCLAMP = 300 V, IC = 2 A 1·0 0·1 0·1 t sv t fi 0·01 0·1 0·01 1·0 IC - Collector Current - A 10 0 20 40 60 80 100 TC - Case Temperature - °C Figure 3. Figure 4. JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 3 BUL791 NPN SILICON POWER TRANSISTOR TYPICAL CHARACTERISTICS INDUCTIVE SWITCHING TIMES vs COLLECTOR CURRENT 10 IB(on) = IC / 5 IB(off) = IC / 8 VCC = 40 V VCLAMP = 300 V L = 1 mH = 25°C TC 1·0 L791CI2 INDUCTIVE SWITCHING TIMES vs CASE TEMPERATURE 10 L791CI4 tsv tfi Inductive Switching Time - µs IB(on) = 400 mA, VCC = 40 V, L = 1 mH IB(off) = 250 mA, VCLAMP = 300 V, IC = 2 A Inductive Switching Time - µs 1·0 t sv t fi 0·1 0·1 0·1 1·0 IC - Collector Current - A 10 0 20 40 60 80 100 TC - Case Temperature - °C Figure 5. Figure 6. RESISTIVE SWITCHING TIMES vs COLLECTOR CURRENT 10 IB(on) IB(off) Resistive Switching Time - µs = IC / 5, VCC = 300 V = IC / 5, TC = 25°C Resistive Switching Time - µs L791CR1 RESISTIVE SWITCHING TIMES vs CASE TEMPERATURE 10 IB(on) = 400 mA, VCC = 300 V IB(off) = 400 mA, IC = 2 A L791CR2 1·0 1·0 tsv tfi 0·1 0·1 0·1 1·0 IC - Collector Current - A 10 0 t sv t fi 20 40 60 80 100 TC - Case Temperature - °C Figure 7. Figure 8. 4 JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP BUL791 NPN SILICON POWER TRANSISTOR MAXIMUM SAFE OPERATING REGIONS MAXIMUM FORWARD-BIAS SAFE OPERATING AREA 10 L791CFB MAXIMUM REVERSE-BIAS SAFE OPERATING AREA 10 L791CRB 8 1·0 IC - Collector Current - A IC - Collector Current - A IB(on) = IC / 5 VBE(off) = -5 V TC = 25°C 6 0·1 TC = 25°C tp = 10 µs tp = 100 µs tp = 1 m s tp = 10 ms DC Operation 10 100 1000 4 2 0·01 1·0 0 0 100 200 300 400 500 600 700 800 VCE - Collector-Emitter Voltage - V VCE - Collector-Emitter Voltage - V Figure 9. Figure 10. JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP 5 BUL791 NPN SILICON POWER TRANSISTOR MECHANICAL DATA TO-220 3-pin plastic flange-mount package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. TO220 4,70 4,20 ø 3,96 3,71 10,4 10,0 2,95 2,54 6,6 6,0 15,90 14,55 1,32 1,23 see Note B see Note C 6,1 3,5 0,97 0,61 1 2 3 1,70 1,07 14,1 12,7 2,74 2,34 5,28 4,88 2,90 2,40 0,64 0,41 VERSION 1 VERSION 2 ALL LINEAR DIMENSIONS IN MILLIMETERS NOTES: A. The centre pin is in electrical contact with the mounting tab. B. Mounting tab corner profile according to package version. C. Typical fixing hole centre stand off height according to package version. Version 1, 18.0 mm. Version 2, 17.6 mm. MDXXBE 6 JULY 1991 - REVISED SEPTEMBER 2002 Specifications are subject to change without notice. NOITAMROFNI TCUDORP