CD214A-FS150

M PL I AN T Features This series is currently available but not recommended for new designs. Recommended replacement products are available. *R o HS CO RoHS compliant* Glass passivated chip Low reverse leakage current Low forward voltage drop High current capability CD214A-F150~F1600 Fast Response Rectifiers General Information The markets of portable communications, computing and video equipment are challenging the semiconductor industry to develop increasingly smaller electronic components. Bourns offers Glass Passivated Rectifiers for rectification applications, in compact chip DO-214AC (SMA) size format, which offer PCB real estate savings and are considerably smaller than most competitive parts. The Glass Passivated Rectifier Diodes offer a forward current of 1.0 A with a choice of repetitive peak reverse voltage of 50 V up to 600 V. Bourns® Chip Diodes conform to JEDEC standards, are easy to handle on standard pick and place equipment and their flat configuration minimizes roll away. Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted) Parameter Symbol Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage CD214A- Unit F150 F1100 F1150 F1200 F1400 F1600 VRRM 50 100 150 200 400 600 V VRMS 35 70 105 140 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 400 600 V Maximum Average Forward Rectified Current1 I(AV) 1.0 A DC Reverse Current @ Rated DC Blocking Voltage (@TA = 25 °C) IR 5.0 μA DC Reverse Current @ Rated DC Blocking Voltage (@TA = 125 °C) IR 50.0 μA Typical Junction Capacitance CJ 10 pF 2 Maximum Instantaneous Forward Voltage @ 1 A Typical Thermal Resistance VF 0.95 1.25 RθJA 3 1.7 34 V °C/W Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30 25 A Maximum Reverse Recovery Time 4 Trr 25 35 ns Typical Reverse Recovery Time 4 Trr 20 30 ns Notes: 1 See Forward Derating Curve. 2 Measured at 1 MHz and an applied reverse voltage of 4.0 V. 3 Thermal resistance from junction to ambient and from junction to lead P.C.B. mounted on 0.2 x 0.2 (5.0 x 5.0 mm) copper pad areas. 4 Reverse recovery test condition: IF 0.5 A, IR = 1.0 A, Irr = 0.25 A. Thermal Characteristics (@ TA = 25 °C Unless Otherwise Noted) Parameter Symbol CD214A-F150~F1600 Unit TJ -55 to +150 °C TSTG -55 to +150 °C Operating Temperature Range Storage Temperature Range WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CD214A-F150~F1600 Fast Response Rectifiers Product Dimensions Recommended Pad Layout This is an RoHS compliant product using 100 % Sn termination. It is a molded plastic package. A cathode band indicates the polarity. The package weighs approximately 0.064 g. The package and dimensions are shown below. 2.69 MAX. (0.106) 4.00 - 4.60 (0.160 - 0.180) 2.10 MIN. (0.083) 1.27 - 1.63 (0.05 - 0.064) 2.29 - 2.92 (0.090 - 0.115) 1.27 MIN. (0.050) DIMENSIONS: MM (INCHES) How To Order CD 214A - F 1 400 2.00 - 2.43 (0.079 - 0.103) 0.05 - 0.20 (0.002 - 0.008) 0.76 - 1.27 (0.03 - 0.06) 4.83 - 5.59 (0.190 - 0.220) DIMENSIONS: MM (INCHES) 0.15 - 0.31 (0.006 - 0.012) Common Code CD = Chip Diode Package 214A = DO214AC Model Series F = Fast Response Forward Current 1=1A Reverse Voltage 50 = 50 V 100 = 100 V 150 = 150 V 200 = 200 V 400 = 400 V 600 = 600 V Typical Part Marking CD214A-F150 ............................................................................ CD214A-F1100 .......................................................................... CD214A-F1150 .......................................................................... CD214A-F1200 .......................................................................... CD214A-F1400 .......................................................................... CD214A-F1600 .......................................................................... F1A F1B F1C F1D F1G F1J Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CD214A-F150~F1600 Fast Response Rectifiers Performance Graphs Maximum Non-Repetitive Surge Current Forward Current Derating Curve Peak Forward Surge Current (Amps) Average Forward Current (Amps) 1.0 0.5 Resistive or Inductive Load 0 0 50 70 90 110 130 150 170 30 25 20 F1100-F1400 F1600 15 10 Pulse Width 8.3 ms Single Half Sine-Wave (JEDEC Method) 5 0 1 10 Ambient Temperature (°C) 100 Number of Cycles at 60 Hz Typical Forward Characteristics Typical Reverse Characteristics 100 10.00 F50-F100 1.00 Instantaneous Reverse Leakage Current (mA) Instantaneous Forward Current (Amps) F600 F200F400 0.10 Pulsewidth: 300 µs 1% Duty Cycle 10 TJ = 125 °C TJ = 100 °C 1.0 0.1 0.01 0.2 0.6 1.0 1.4 1.8 0 2.2 20 40 60 80 100 110 Percent of Rated Peak Reverse Voltage (%) Instantaneous Forward Voltage (Volts) Typical Junction Capacitance 200 100 Junction Capacitance (pF) 60 40 20 10 6 4 TJ = 25 °C 2 1 0.1 0.2 0.4 1.0 2 4 10 Reverse Voltage (Volts) 20 40 100 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CD214A-F150~F1600 Fast Response Rectifiers Packaging Information The surface mount product is packaged in a 12 mm x 4 mm tape and reel format per EIA-481 standard. P 0 P 1 d T E Index Hole 120 F D2 W B D1 D P A Trailer ....... ....... End C Device ....... ....... ....... ....... Leader ....... ....... W1 Start DIMENSIONS: 10 pitches (min.) 10 pitches (min.) MM (INCHES) Direction of Feed Item Symbol Carrier Width A Carrier Length B Carrier Depth C Sprocket Hole d Reel Outside Diameter D Reel Inner Diameter D1 Feed Hole Diameter D2 Sprocket Hole Position E Punch Hole Position F Punch Hole Pitch P Sprocket Hole Pitch P0 Embossment Center P1 Overall Tape Thickness T Tape Width W Reel Width W1 Quantity per Reel — DO-214AC (SMA) 3.42 ± 0.10 (0.134 ± 0.004) 5.07 ± 0.10 (0.199 ± 0.004) 3.10 ± 0.10 (0.122 ± 0.004) 1.55 ± 0.05 (0.061 ± 0.002) 330 (12.992) 50.0 Min. (1.969) 13.0 ± 0.50 (0.512 ± 0.020) 1.75 ± 0.10 (0.069 ± 0.004) 5.50 ± 0.50 (0.217 ± 0.020) 4.00 ± 0.10 (0.157 ± 0.004) 4.00 ± 0.10 (0.157 ± 0.004) 2.00 ± 0.05 (0.079 ± 0.002) 0.30 ± 0.10 (0.012 ± 0.004) 12.00 ± 0.20 (0.420 ± 0.008) 18.7 Max. (0.736) 7,500 Asia-Pacific: Tel: +886-2 2562-4117 Email: asiacus@bourns.com Europe: Tel: +36 88 885 877 Email: eurocus@bourns.com The Americas: Tel: +1-951 781-5500 Email: americus@bourns.com www.bourns.com REV. 05/20 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹ Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change ^P[OV\[UV[PJL