CHP0603-FX-3011ELF

CO M G E & PL I AN N FR T* EE ** HS LO Ro HA 01B Features Applications ■ Thick film technology ■ Power supplies ■ Power rating up to 3 watts @ 70 °C ■ Digital meters ■ High power surge withstanding ■ Consumer electronics ■ RoHS compliant* ■ LED lighting ■ Halogen free** ■ Industry control boards CHP Series Ultra-High Power Chip Resistors Electrical Characteristics Model Characteristic Power Rating @ 70 °C CHP0603 CHP0805 CHP1206 CHP2512 0.33 W 0.5 W 0.75 W 3W Operating Temperature Range -55 °C to +155 °C Derated to Zero Load at Maximum Working Voltage 1 ohm to 1 megohm 0.1 ohm to 0.91 ohm Maximum Overload Voltage 1 ohm to 1 megohm 0.1 ohm to 0.91 ohm +155 °C 75 V – 200 V – 250 V – 250 V 1652 mV 125 V – 300 V – 500 V – 500 V 3695 mV Resistance Tolerance ±1 %, ±5 % Temperature Coefficient 1 ohm to 9.76 ohms (±1 %, E24 & E96 Series) ±200 ppm/°C ±150 ppm/°C*** ±100 ppm/°C ±100 ppm/°C 10 ohms to 1 megohm (±1 %, E24 & E96 Series) ±100 ppm/°C ±100 ppm/°C ±100 ppm/°C ±100 ppm/°C 1 ohm to 1 megohm (±5 %, E24 Series ±200 ppm/°C ±200 ppm/°C ±200 ppm/°C ±200 ppm/°C 0.1 ohm to 0.91 ohm (±1 %, E24 Series) – – – ±100 ppm/°C 0.1 ohm to 0.91 ohm (±5 %, E24 Series) – – – ±200 ppm/°C ***TCR code assigned as “X” - see How to Order chart. Note: Solder pad and trace size should be evaluated and board surface temperature should not exceed +105 °C when applying full rated power. Additional Information Click these links for more information: For Standard Values Used in Capacitors, Inductors and Resistors, click here. PRODUCT TECHNICAL INVENTORY SAMPLES SELECTOR LIBRARY CONTACT Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com www.bourns.com WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov * RoHS Directive 2015/863, Mar 31, 2015 and Annex. **Bourns considers a product to be “halogen free” if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CHP Series Ultra-High Power Chip Resistors Product Dimensions Model L W C D L T CHP0603 1.60 ± 0.10 0.80 ± 0.10 0.30 ± 0.20 0.30 ± 0.30 0.45 ± 0.10 (0.063 ± 0.004) (0.031 ± 0.004) (0.012 ± 0.008) (0.012 ± 0.008) (0.018 ± 0.004) CHP0805 2.00 ± 0.10 1.25 ± 0.10 0.40 ± 0.20 0.40 ± 0.20 0.50 ± 0.10 (0.079 ± 0.004) (0.049 ± 0.004) (0.016 ± 0.008) (0.016 ± 0.008) (0.020 ± 0.04) CHP1206 3.10 ± 0.10 1.60 ± 0.10 0.50 ± 0.25 0.50 ± 0.25 0.55 ± 0.10 (0.122 ± 0.004) (0.063 ± 0.004) (0.020 ± 0.010) (0.020 ± 0.010) (0.022 ± 0.004) CHP2512 6.40 ± 0.20 3.10 ± 0.20 0.45 ± 0.25 1.80 ± 0.25 1.10 ± 0.20 (0.252 ± 0.008) (0.122 ± 0.008) (0.018 ± 0.010) (0.071 ± 0.010) (0.043 ± 0.008) DIMENSIONS: 100 W C C T D MM (INCHES) D Recommended Solder Pad Layout Model A B L CHP0603 0.90 (0.035) 1.00 (0.039) 3.00 (0.118) CHP0805 1.30 (0.051) 1.15 (0.045) 3.50 (0.138) CHP1206 1.80 (0.071) 1.30 (0.051) 4.70 (0.185) CHP2512 3.70 (0.146) 2.45 (0.096) 7.60 (0.299) L A B DIMENSIONS: MM (INCHES) Surge Performance Peak Power (Watts) 1000 100 10 CHP2512 CHP1206 1 0.1 0.0001 CHP0805 CHP0603 0.001 0.01 0.1 1 Pulse Duration (Seconds) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CHP Series Ultra-High Power Chip Resistors Construction Environmental Characteristics Moisture Sensitivity Level ...........................................................1 OVERCOAT (BLACK) CONDUCTOR Derating Curve RESISTIVE ELEMENT Power Ratio (%) Sn PLATING Ni PLATING CERAMIC SUBSTRATE Rated Voltage The rated voltage is calculated by the following formula: V= P X R 100 -55 V: Rated Voltage (V) P: Rated Power (W) R: Resistance Value (Ω) 70 155 Ambient Temperature (°C) Soldering Profile 275 Maximum of 20 seconds between 260 °C peak +255 °C and +260 °C 255 °C 225 Temperature (°C) 220 °C 190 °C 175 90 - 150 seconds Ramp Down 6 °C/second 150 °C 125 60 - 120 seconds 10 seconds minimum 75 Ramp Up 3 °C/second maximum 25 0 50 100 150 Time (seconds) 200 250 300 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CHP Series Ultra-High Power Chip Resistors How to Order CHP 0603 - F X - 1002 E LF Model CHP = High Power Surge Resistor Size 0603 = 0603 Size 0805 = 0805 Size 1206 = 1206 Size 2512 = 2512 Size Resistance Tolerance F = ±1 % J = ±5 % TCR (See Electrical Characteristics chart) W = ±200 PPM/°C X = ±100 PPM/°C (also includes CHP0805: 1 ohm to 9.76 ohms = ±150 PPM/°C) Resistance Value 1 % Tolerance: 155 °C (30 min.) --> 25 °C (2~2 min.) 1.5 hours at rated voltage followed by a pause of 0.5 hour at 70 ± 2 °C; Cycle repeated for 1000 hours 40 ±2 °C with 90~95 % relative humidity; DC rated voltage for 1.5 hours “ON”, 0.5 hour “OFF”; Cycle repeated for 1000 hours Resistance to Solder Heat 260 ±5 °C for 10 ±1 seconds Solderability After immersing flux, dip in 245 ±2 °C molten solder bath for 3 ± 0.5 seconds Board Flex Bending 2 mm Test Limits ΔR 1 % Tolerance ≤ ±1 % 5 % Tolerance ≤ ±2 % 1 % Tolerance ≤ ±0.5 % 5 % Tolerance ≤ ±1 % 1 % Tolerance ≤ ±1 % 5 % Tolerance ≤ ±3 % 1 % Tolerance ≤ ±1 % 5 % Tolerance ≤ ±3 % 1 % Tolerance ≤ ±0.5 % 5 % Tolerance ≤ ±1 % At least 95 % of termination must be covered with solder.. 1 % Tolerance ≤ ±0.5 % 5 % Tolerance ≤ ±1 % Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CHP Series Ultra-High Power Chip Resistors Typical Part Marking ±5 % (E24): 301 CHP0603, CHP0805, CHP1206, CHP2512 Resistance value is expressed by 3 digits. The first two digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. Example: 301 = 30 x 101 = 300 ohms ±1 % (E24/E96): CHP0805, CHP1206, CHP2512 Resistance value is expressed by 4 digits. The first three digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. 1542 Example: 1542 = 154 x 102 = 15.4K ohms ±1 % (E24): 222 CHP0603 Resistance value is expressed by 3 digits. The first two digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. Example: 222 = 22 x 102 = 2.2K ohms ±1 % (E96): 01B CHP0603 Resistance value is expressed by 2 digits followed by an alpha character multiplier. (Refer to marking table below.) Example: 01B = 100 x 101 = 1K ohms Code R Value Code R Value Code R Value Code Code R Value 01 100 13 133 25 178 37 R Value Code 237 49 R Value 316 Code R Value 61 422 73 562 Code R Value 85 750 02 102 14 137 26 182 38 243 50 324 62 432 74 576 86 768 03 105 15 140 27 187 39 249 51 332 63 442 75 590 87 787 04 107 16 143 28 191 40 255 52 340 64 453 76 604 88 806 05 110 17 147 29 196 41 261 53 348 65 464 77 619 89 825 06 113 18 150 30 200 42 267 54 357 66 475 78 634 90 845 07 115 19 154 31 205 43 274 55 365 67 487 79 649 91 866 08 118 20 158 32 210 44 280 56 374 68 499 80 665 92 887 09 121 21 162 33 215 45 287 57 383 69 511 81 681 93 909 10 124 22 165 34 221 46 294 58 392 70 523 82 698 94 931 11 127 23 169 35 226 47 301 59 402 71 536 83 715 95 953 12 130 24 174 36 232 48 309 60 412 72 549 84 732 96 976 This table shows the first two digits for the three-digit E96 part marking scheme. The third character is a letter multiplier: A=100 B=101 C=102 D=103 E=104 F=105 G=10-6 H=10-7 X=10-1 Y=10-2 Z=10-3 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CHP Series Ultra-High Power Chip Resistors Packaging Dimensions (Conforms to EIA RS-481A) CHP0603, CHP0805, CHP1206: CHP2512: 2.00 ± 0.05 (.079 ± .002) 4.00 ± 0.10 (.157 ± .004) 1.50 +0.10/-0 DIA. (.059 +.004/-0) 14.9 (.587) MAX. 16.7 (.657) MAX. 2.0 ± 0.5 (.079 ± .020) 1.75 ± 0.10 (.069 ± .004) 13.0 ± 0.5 (.512 ± .020) W 60.0 ± 0.5 (2.36 ± .020) F B 4.00 ± 0.10 (.157 ± .004) A Model Tape Type MIN. Pieces per Reel CHP0603 CHP0805 Paper 5,000 CHP1206 CHP2512 Plastic 3,000 20 (.787) CHP0603, CHP0805, CHP1206: 10.0 ± 1.5 (.394 ± .059) CHP2512: 13.8 ± 1.5 (.543 ± .059) A B 1.10 ± 0.20 (.043 ± .008) 1.90 ± 0.20 (.075 ± .008) 1.65 ± 0.20 (.065 ± .008) 2.40 ± 0.20 (.094 ± .008) 2.00 ± 0.20 (.079 ± .008) 3.60 ± 0.20 (.142 ± .008) 3.50 ± 0.20 (.138 ± .008) 6.70 ± 0.20 (.264 ± .008) DIMENSIONS: 178.0 ± 2.0 (7.008 ± .080) W F 8.00 ± 0.30 (.315 ± .012) 3.50 ± 0.05 (.138 ± .002) 12.00 ± 0.30 (.472 ± .012) 5.50 ± 0.05 (.217 ± .002) MM (INCHES) REV. 05/29/20 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹ Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change ^P[OV\[UV[PJL