CMP0603-FX-1004ELF

CO LO & MP LI GE AN N T FR EE *R oH S ** HA 301 Features Applications ■ Thick film technology ■ Power supplies ■ Power rating up to 1.5 watts @ 70 °C ■ Digital meters ■ High power surge withstanding ■ Consumer electronics ■ RoHS compliant* ■ LED lighting ■ Halogen free** ■ Industry control boards CMP Series High Power Anti-Surge Chip Resistors Electrical Characteristics Model Characteristic Power Rating @ 70 °C CMP0603 CMP0805 CMP1206 CMP2010 CMP2512 0.25 W 0.5 W 0.75 W 1W 1.5 W Operating Temperature Range -55 °C to +155 °C Derated to Zero Load at +155 °C Maximum Working Voltage 75 V 200 V 250 V 200 V 300 V Maximum Overload Voltage 125 V 300 V 500 V 400 V 600 V Resistance Tolerance Temperature Coefficient 10 Ω to 1 MΩ (±1 %, E24 & E96 Series) 10 Ω to 1 MΩ (±5 %, E24 Series ±1 %, ±5 % ±100 ppm/°C ±100 ppm/°C ±100 ppm/°C ±100 ppm/°C ±100 ppm/°C ±200 ppm/°C ±200 ppm/°C ±200 ppm/°C ±200 ppm/°C ±200 ppm/°C Note: Solder pad and trace size should be evaluated and board surface temperature should not exceed +105 °C when applying full rated power. Additional Information Click these links for more information: PRODUCT TECHNICAL INVENTORY SAMPLES SELECTOR LIBRARY CONTACT Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com www.bourns.com WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov * RoHS Directive 2015/863, Mar 31, 2015 and Annex. ** Bourns considers a product to be “halogen free” if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CMP Series High Power Anti-Surge Chip Resistors Product Dimensions Model L W C D T CMP0603 1.60 ± 0.10 (.063 ± .004) 0.80 ± 0.10 (.031 ± .004) 0.30 ± 0.20 (.012 ± .008) 0.30 ± 0.20 (.012 ± .008) 0.45 ± 0.10 (.018 ± .004) CMP0805 2.00 ± 0.10 (.079 ± .004) 1.25 ± 0.10 (.049 ± .004) 0.40 ± 0.20 (.016 ± .008) 0.40 ± 0.20 (.016 ± .008) 0.50 ± 0.10 (.020 ± .004) CMP1206 3.10 ± 0.10 (.122 ± .004) 1.60 ± 0.10 (.063 ± .004) 0.50 ± 0.25 (.020 ± .010) 0.50 ± 0.25 (.020 ± .010) 0.55 ± 0.10 (.022 ± .004) CMP2010 5.00 ± 0.20 (.197 ± .008) 2.50 ± 0.20 (.098 ± .008) 0.65 ± 0.25 (.026 ± .010) 0.60 ± 0.25 (.023 ± .010) 0.60 ± 0.10 (.024 ± .004) CMP2512 6.40 ± 0.20 (.252 ± .008) 3.10 ± 0.20 (.122 ± .008) 0.60 ± 0.25 (.024 ± .010) 1.80 ± 0.25 (.071 ± .010) 0.60 ± 0.15 (.024 ± .006) DIMENSIONS: L W C C T D D MM (INCHES) Recommended Solder Pad Layout Model A B L CMP0603 0.90 (.035) 1.00 (.039) 3.00 (.118) CMP0805 1.30 (.051) 1.15 (.045) 3.50 (.138) CMP1206 1.80 (.071) 1.30 (.051) 4.70 (.185) CMP2010 3.00 (.118) 1.50 (.059) 6.80 (.268) CMP2512 3.70 (.146) 2.45 (.096) 7.60 (.299) L A B DIMENSIONS: MM (INCHES) Surge Performance Peak Power (Watts) 1000 100 10 CMP2512 CMP2010 CMP1206 CMP0805 CMP0603 1 0.1 0.0001 0.001 0.01 0.1 1 Pulse Duration (Seconds) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CMP Series High Power Anti-Surge Chip Resistors Construction Environmental Characteristics Moisture Sensitivity Level ...........................................................1 OVERCOAT (BLACK) CONDUCTOR Sn PLATING RESISTIVE ELEMENT Power Ratio (%) Derating Curve Ni PLATING CERAMIC SUBSTRATE Rated Voltage The rated voltage is calculated by the following formula: 100 -55 V= P X R 70 155 Ambient Temperature (°C) V: Rated Voltage (V) P: Rated Power (W) R: Resistance Value (Ω) Soldering Profile 275 Maximum of 20 seconds between 260 °C peak +255 °C and +260 °C 255 °C 225 Temperature (°C) 220 °C 190 °C 175 90 - 150 seconds Ramp Down 6 °C/second 150 °C 125 60 - 120 seconds 10 seconds minimum 75 Ramp Up 3 °C/second maximum 25 0 50 100 150 Time (seconds) 200 250 300 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CMP Series High Power Anti-Surge Chip Resistors How to Order CMP 0603 - F X - 1002 E LF Model CMP = High Power Anti-Surge Resistor Size 0603 = 0603 Size 0805 = 0805 Size 1206 = 1206 Size 2010 = 2010 Size 2512 = 2512 Size Resistance Tolerance F = ±1 % J = ±5 % TCR (See Electrical Characteristics chart) W = ±200 PPM/°C X = ±100 PPM/°C Resistance Value 1 % Tolerance: 25 °C (2-3 min.)--> 155 °C (30 min.) --> 25 °C (2~3 min.) 1 % Tolerance ≤ ± (0.5 % + 0.05 Ω) 5 % Tolerance ≤ ± (1 % + 0.05 Ω) Load Life 1.5 hours at rated voltage followed by a pause of 0.5 hour at 70 ± 2 °C; Cycle repeated for 1000 hours 1 % Tolerance ≤ ± (1 % + 0.05 Ω) 5 % Tolerance ≤ ± (3 % + 0.05 Ω) Load Life with Humidity 40 ±2 °C with 90~95 % relative humidity; DC rated voltage for 1.5 hours “ON”, 0.5 hour “OFF”; Cycle repeated for 1000 hours 1 % Tolerance ≤ ± (1 % + 0.05 Ω) 5 % Tolerance ≤ ± (3 % + 0.05 Ω) Resistance to Solder Heat 260 ±5 °C for 10 ±1 seconds 1 % Tolerance ≤ ± (0.5 % + 0.05 Ω) 5 % Tolerance ≤ ± (1 %) + 0.05 Ω Solderability After immersing flux, dip in 245 ±2 °C molten solder bath for 3 ± 0.5 seconds At least 95 % of termination must be covered with solder.. Board Flex Bending 2 mm 1 % Tolerance ≤ ± (0.5 % + 0.05 Ω) 5 % Tolerance ≤ ± (1 % + 0.05 Ω) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CMP Series High Power Anti-Surge Chip Resistors Typical Part Marking ±5 % (E24): 301 CMP0603, CMP0805, CMP1206, CMP2010, CMP2512 Resistance value is expressed by 3 digits. The first two digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. Example: 301 = 30 x 101 = 300 ohms ±1 % (E24/E96): 1542 CMP0805, CMP1206, CMP2010, CMP2512 Resistance value is expressed by 4 digits. The first three digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. Example: 1542 = 154 x 102 = 15.4K ohms ±1 % (E24): 222 CMP0603 Resistance value is expressed by 3 digits. The first two digits represent the significant figures of the nominal resistance value in ohms; the third digit represents the exponent for a base of 10. Example: 222 = 22 x 102 = 2.2K ohms ±1 % (E96): 01B CMP0603 Resistance value is expressed by 2 digits followed by an alpha character multiplier. (Refer to marking table below.) Example: 01B = 100 x 101 = 1K ohms This table shows the first two digits for the three-digit E96 part marking scheme. The third character is a letter multiplier: A=100 B=101 C=102 D=103 E=104 F=105 G=106 H=107 X=10-1 Y=10-2 Z=10-3 Code R Value Code R Value Code R Value Code R Value Code R Value 01 100 21 162 41 261 61 422 81 681 02 102 22 165 42 267 62 432 82 698 03 105 23 169 43 274 63 442 83 715 04 107 24 174 44 280 64 453 84 732 05 110 25 178 45 287 65 464 85 750 06 113 26 182 46 294 66 475 86 768 07 115 27 187 47 301 67 487 87 787 08 118 28 191 48 309 68 499 88 806 09 121 29 196 49 316 69 511 89 825 10 124 30 200 50 324 70 523 90 845 11 127 31 205 51 332 71 536 91 866 12 130 32 210 52 340 72 549 92 887 13 133 33 215 53 348 73 562 93 909 14 137 34 221 54 357 74 576 94 931 15 140 35 226 55 365 75 590 95 953 16 143 36 232 56 374 76 604 96 976 17 147 37 237 57 383 77 619 18 150 38 243 58 392 78 634 19 154 39 249 59 402 79 649 20 158 40 255 60 412 80 665 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. CMP Series High Power Anti-Surge Chip Resistors Packaging Dimensions (Conforms to EIA RS-481A) 14.9 (.587) MAX. 16.7 CMP2010, CMP2512: (.657) MAX. CMP0603, CMP0805, CMP1206: 2.00 ± 0.05 (.079 ± .002) 4.00 ± 0.10 (.157 ± .004) 1.50 +0.10/-0 DIA. (.059 +.004/-0) 2.0 ± 0.5 (.079 ± .020) 1.75 ± 0.10 (.069 ± .004) 13.0 ± 0.5 (.512 ± .020) W 60.0 ± 0.5 (2.36 ± .020) F B 4.00 ± 0.10 (.157 ± .004) A Model Tape Type MIN. Pieces per Reel 20 (.787) CMP0603, CMP0805, CMP1206: 10.0 ± 1.5 (.394 ± .059) CMP2010, CMP2512: 13.8 ± 1.5 (.543 ± .059) A B 1.10 ± 0.20 (.043 ± .008) 1.90 ± 0.20 (.075 ± .008) 1.65 ± 0.20 (.065 ± .008) 2.40 ± 0.20 (.094 ± .008) CMP1206 2.00 ± 0.20 (.079 ± .008) 3.60 ± 0.20 (.142 ± .008) CMP2010 2.80 ± 0.20 (.110 ± .008) 5.50 ± 0.20 (.216 ± .008) 3.50 ± 0.20 (.138 ± .008) 6.70 ± 0.20 (.264 ± .008) CMP0603 CMP0805 Paper Plastic CMP2512 5,000 4,000 DIMENSIONS: 178.0 ± 2.0 (7.008 ± .080) W F 8.00 ± 0.30 (.315 ± .012) 3.50 ± 0.05 (.138 ± .020) 12.00 ± 0.30 (.472 ± .012) 5.50 ± 0.05 (.217 ± .020) MM (INCHES) REV. 05/26/20 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹ Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change ^P[OV\[UV[PJL