*R
AE **H oHS
C- AL C
Q2 OG OM
00 EN P
CO FR LIA
M EE NT
PL & ,
IA
NT
Features
n Thick film technology
n Power rating up to 1 watt @ 70 °C
n RoHS compliant*
n Halogen free**
n Sulfur-resistant design (ASTM B-809)
n AEC-Q200 compliant
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Electrical Characteristics
Characteristic
Model No.
CR0201A-AS
CR0402A-AS
CR0603A-AS
CR0805A-AS
Power Rating @ 70 °C
0.05 W
0.063 W
0.1 W
0.125 W
Operating Temp. Range
-55 to +125 °C
-55 to +155 °C
Derated to Zero Load at
+125 °C
+155 °C
Maximum Working Voltage (1)
25 V
50 V
50 V
150 V
Maximum Overload Voltage
50 V
100 V
100 V
300 V
1 Ω ~ 9.76 Ω
±400 ppm/°C
1 Ω ~ 9.76 Ω
±400 ppm/°C
10 Ω ≤ R ≤ 1M Ω
±100 ppm/°C
10 Ω ≤ R ≤ 1M Ω
±100 ppm/°C
1M Ω < R ≤ 10M Ω
±200 ppm/°C
1M Ω < R ≤ 10M Ω
±200 ppm/°C
1 Ω ~ 9.1 Ω
10M < R ≤ 20M Ω
±400 ppm/°C
1 Ω ~ 9.1 Ω
10M < R ≤ 20M Ω
±400 ppm/°C
10 Ω ≤ R ≤ 10M Ω
±200 ppm/°C
10 Ω ≤ R ≤ 10M Ω
±200 ppm/°C
1 A / 2.5 A
2A/5A
Resistance Tolerance
Temperature Coefficient @ 1 %
(E24 + E96)
Temperature Coefficient @ 5 %
(E24)
Zero Ohm Jumper ≤ 0.05 Ω
Rated / Max. Current
(1)
±1 %, ±5 %
1 Ω ~ 9.76 Ω
-200 ~ +600 ppm/°C
10 Ω ~ 3M Ω
+200 ppm/°C
1 Ω ~ 9.1 Ω
-200 ~ +600 ppm/°C
10 Ω ~ 10M Ω
+200 ppm/°C
1 Ω ~ 9.76 Ω
-200 ~ +500 ppm/°C
100 Ω ≤ R ≤ 1M Ω
±100 ppm/°C
10 Ω ≤ R < 100 Ω
1M Ω < R ≤ 10M Ω
±200 ppm/°C
1 Ω ~ 9.1 Ω
-200 ~ +500 ppm/°C
10 Ω ≤ R ≤ 10M Ω
±200 ppm/°C
10M Ω ≤ R ≤ 20M Ω
±400 ppm/°C
0.5 A / 1 A
1 A / 2.5 A
Maximum Working Voltage is calculated with formula V= √P*R with the maximum value from the Electrical Characteristics table.
Environmental Characteristics
Moisture Sensitivity Level........................................................... 1
ESD Classification (HBM).........................................................1A
WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
* RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
** Bourns considers a product to be “halogen free” if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less;
and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Electrical Characteristics (continued)
Characteristic
Power Rating @ 70 °C
Model No.
CR1206A-AS
CR1210A-AS
CR2010A-AS
CR2512A-AS
0.25 W
0.33 W
0.5 W
1W
Operating Temp. Range
-55 to +155 °C
Derated to Zero Load at
+155 °C
Maximum Working Voltage (1)
200 V
Maximum Overload Voltage
400 V
Resistance Tolerance
±1 %, ±5 %
1 Ω ~ 9.76 Ω
±400 ppm/°C
Temperature Coefficient @ 1 %
(E24 + E96)
10 Ω ≤ R ≤ 1M Ω
±100 ppm/°C
1M Ω < R ≤ 10M Ω
±200 ppm/°C
Temperature Coefficient @ 5 %
(E24)
Zero Ohm Jumper ≤ 0.05 Ω
Rated / Max. Current
(1)
1 Ω ~ 9.1 Ω
10M < R ≤ 20M Ω
±400 ppm/°C
10 Ω ≤ R ≤ 10M Ω
±200 ppm/°C
2A/5A
Maximum Working Voltage is calculated with formula V= √P*R with the maximum value from the Electrical Characteristics table.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Product Dimensions
L
W
C
D
DIMENSIONS:
MM
(INCHES)
T
Model
L
W
C
D
T
CR0201A-AS
0.60 ± 0.03
(.024 ± .001)
0.30 ± 0.03
(.012 ± .001)
0.10 ± 0.05
(.004 ± .002)
0.15 ± 0.05
(.006 ± .002)
0.23 ± 0.03
(.009 ± .001)
CR0402A-AS
1.00 ± 0.10
(.039 ± .004)
0.50 ± 0.05
(.020 ± .002)
0.20 ± 0.10
(.008 ± .004)
0.25 ± 0.10
(.010 ± .004)
0.32 ± 0.05
(.013 ± .002)
CR0603A-AS
1.60 ± 0.10
(.063 ± .004)
0.80 ± 0.10
(.031 ± .004)
0.30 ± 0.20
(.012 ± .008)
0.30 ± 0.20
(.012 ± .008)
0.45 ± 0.10
(.018 ± .004)
CR0805A-AS
2.00 ± 0.10
(.079 ± .004)
1.25 ± 0.10
(.049 ± .004)
0.40 ± 0.20
(.016 ± .008)
0.40 ± 0.20
(.016 ± .008)
0.50 ± 0.10
(.020 ± .004)
CR1206A-AS
3.10 ± 0.10
(.122 ± .004)
1.55 ± 0.10
(.061 ± .004)
0.50 ± 0.30
(.020 ± .012)
0.40 ± 0.20
(.016 ± .008)
0.55 ± 0.10
(.022 ± .004)
CR1210A-AS
3.10 ± 0.10
(.122 ± .004)
2.55 ± 0.10
(.100 ± .004)
0.50 ± 0.30
(.020 ± .012)
0.40 ± 0.20
(.016 ± .008)
0.60 ± 0.10
(.024 ± .004)
CR2010A-AS
5.00 ± 0.15
(.197 ± .006)
2.50 ± 0.15
(.098 ± .006)
0.60 ± 0.30
(.024 ± .012)
0.50 ± 0.25
(.020 ± .010)
0.60 ± 0.10
(.024 ± .004)
CR2512A-AS
6.30 ± 0.20
(.248 ± .008)
3.20 ± 0.20
(.126 ± .008)
0.60 ± 0.30
(.024 ± .012)
0.50 ± 0.25
(.020 ± .010)
0.60 ± 0.10
(.024 ± .004)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Recommended Pad Layout
RESISTOR
c
a
b
DIMENSIONS:
MM
(INCHES)
Model
a
b
c
CR0201A-AS
0.25 ~ 0.30
(.010 ~ .012)
0.70 ~ 0.90
(.028 ~ .035)
0.30 ~ 0.40
(.012 ~ .016)
CR0402A-AS
0.50 ~ 0.60
(.020 ~ .024)
1.40 ~ 1.60
(.055 ~ .063)
0.40 ~ 0.60
(.012 ~ .024)
CR0603A-AS
0.70 ~ 0.90
(.028 ~ .035)
2.00 ~ 2.20
(.079 ~ .087)
0.80 ~ 1.00
(.031 ~ .039)
CR0805A-AS
1.00 ~ 1.40
(.039 ~ .055)
3.20 ~ 3.80
(.126 ~ .150)
0.90 ~ 1.40
(.035 ~ .055)
CR1206A-AS
2.00 ~ 2.40
(.079 ~ .094)
4.40 ~ 5.00
(.173 ~ .197)
1.20 ~ 1.80
(.047 ~ .071)
CR1210A-AS
2.00 ~ 2.40
(.079 ~ .094)
4.50 ~ 5.00
(.177 ~ .197)
2.30 ~ 3.50
(.091 ~ .138)
CR2010A-AS
3.30 ~ 3.70
(.130 ~ .146)
5.70 ~ 6.50
(.224 ± .256)
2.30 ~ 3.50
(.091 ~ .138)
CR2512A-AS
3.60 ~ 4.00
(.142 ~ .157)
7.60 ~ 8.60
(.299 ~ .339)
2.30 ~ 3.50
(.091 ~ .138)
Soldering Profile
275
Maximum of 20 seconds between
+255 °C and +260 °C
260 °C peak
255 °C
Temperature (°C)
225
220 °C
190 °C
60 - 90
seconds
175
Ramp Down
6 °C/second
150 °C
125
60 - 120 seconds
10 seconds minimum
75
Ramp Up
3 °C/second maximum
25
0
50
100
150
200
250
300
Time (Seconds)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Performance Characteristics (AEC-Q200)
Test
Method
Procedure
Test Limits ∆R
Short Time Overload
IEC 60115-1 4.13
2.5 X rated voltage for 5 sec.
± (1 % + 0.05 Ω )
Remarks:
0201: ± (3 % + 0.1 Ω)
0402: ± (2 % + 0.1 Ω)
0 Ω : 50 mΩ or less
High Temperature Exposure
(Storage)
AEC-Q200-REV D-Test 3
MIL-STD-202 Method 108
1000 hrs. @ T=155 °C. Unpowered.
Measurement at 24 ±2 hours after test conclusion.
1 %: ± (1.0 % + 0.05 Ω)
5 %: ± (2.0 % + 0.1 Ω)
0201: ± (3 % + 0.1 Ω)
0 Ω: 50 mΩ or less
Temperature Cycling
AEC-Q200-REV D-Test 4
JESD22 Method JA-104
1000 cycles (-55 °C to +125 °C)
Measurement at 24 ±4 hours after test conclusion.
30 min. maximum dwell time at each temperature extreme.
1 min. maximum transition time.
± (1.0 % + 0.1 Ω)
0201: ± (2 % + 0.1 Ω)
0 Ω: 50 mΩ or less
Moisture Resistance
AEC-Q200-REV D-Test 6
MIL-STD-202 Method 106
T=24 hours / Cycle,10 Cycles.
Notes: Steps 7a & 7b not required. Unpowered.
1 %: ± (1.0 % + 0.05 Ω)
2 %, 5 %: ± (2.0 % + 0.1 Ω)
0201: ± (3 % + 0.1 Ω)
0 Ω: 50 mΩ or less
Biased Humidity
AEC-Q200-REV D-Test 7
MIL-STD-202 Method 103
1000 hours 85 °C / 85 % RH. Note: Specified conditions:
10 % of operating power (not exceeding max. working voltage).
Measurement at 24 ±2 hours after test conclusion.
Operational Life
AEC-Q200-REV D-Test 8
MIL-STD-202 Method 108
1000 hours Ta=125 °C at 35 % rated power. Measurement at 24 ±4
hours after test conclusion.
AEC-Q200-REV D-Test 9
MIL-STD-883 Method 2009
AEC-Q200-REV D-Test 10
JESD22 Method JB-100
Electrical test not required. Inspect device construction, marking and
workmanship.
External Visual
Physical Dimension
Resistance to Solvents
AEC-Q200-REV D-Test 12
MIL-STD-202 Method 215
± (3 % + 0.1 Ω)
0201: ± (5 % + 0.1 Ω)
0 Ω: 100 mΩ or less
1 %: ± (1 % + 0.1 Ω)
5 %: ± (3 % + 0.1 Ω)
0201: ± (5 % + 0.1 Ω)
0 Ω: 100 mΩ or less
Verify physical dimensions to the applicable device detail spec.
Note: User(s) and Suppliers spec. Electrical test not required.
a: Isopropyl Alcohol : Mineral Spirits = 1:3
b: Terpene Defluxer (Bioact EC-7R)
c: Deionized water : Propylene Glycol
Monomethyl Ether : monoethanolamine = 42:1:1
Marking and protective layer
cannot be detached
AEC-Q200-REV D-Test 13
MIL-STD-202 Method 213
AEC-Q200-REV D-Test 14
MIL-STD-202 Method 204
5 grams for 20 min., 12 cycles each of 3 orientations.
Note: Test from 10-2000 Hz.
Resistance to
Soldering Heat
AEC-Q200-REV D-Test 15
MIL-STD-202 Method 210
Condition B: Immerse the specimens in and eutectic solder at
260 ±5 ℃ for 10 ±1 S.
Thermal Shock
AEC-Q200-REV D-Test 16
MIL-STD-202 Method 107
-55 °C / +155 °C. Note: Number of cycles required: 1000, Maximum
transfer time: 20 seconds,
Dwell time: 15 minutes. Air to Air.
ESD
AEC-Q200-REV D-Test 17
Verify the voltage setting at 500 V
Solderability
AEC-Q200-REV D-Test 18
J-STD-002
> 95 % area covered with tin
Flammability
AEC-Q200-REV D-Test 17
UL-94
Method B, aging 4 hours at 155 °C dry heat
Lead-free solder bath at 235 ±3 °C
Dipping time: 3 ±0.5 seconds
V-0 or V-1 are acceptable.
Electrical test not required.
V-0 or V-1
Board Flex
(Bending)
AEC-Q200-REV D-Test 21
The duration of the applied forces shall be 60 (±5) seconds.
3 mm deflection (0201~1210)
2 mm deflection (2010~2512)
1 %: ± (0.5 % + 0.05 Ω)
5 %: ± (1 % + 0.1 Ω)
0201: ± (1 % + 0.1 Ω)
0 Ω: 50 mΩ or less
Terminal Strength
(SMD)
IEC 60115-1 4.32
Force of 1.8 kg for 60 seconds.
Note: 0201= N/A
± (0.5 % + 0.05 Ω)
0 Ω: 50 mΩ or less
Sulfur (saturated vapor) 1,000 hours,
105 ±2 °C, unpowered
1 %: ± (1 % + 0.05 Ω)
5 %: ± (2 % + 0.05 Ω)
0201:
1 %: ± (2 % + 0.05 Ω)
5 %: ± (3 % + 0.05 Ω)
0 Ω: 100 mΩ or less
Mechanical Shock
Vibration
Sulfuration Test
ASTM-B-809-95
Wave Form: Tolerance for half sine shock pulse. Peak value is
100 grams. Normal duration (D) is 6 ms.
± (1 % + 0.1 Ω)
0 Ω: 50 mΩ or less
± (1 % + 0.1 Ω)
0 Ω: 50 mΩ or less
1 %: ± (0.5 % + 0.05 Ω)
5 %: ± (1 % + 0.1 Ω)
0201: ± (2 % + 0.1 Ω)
0 Ω: 50 mΩ or less
± (1 % + 0.1 Ω)
0201: ± (2 % + 0.1 Ω)
0 Ω: 50 mΩ or less
± (1 % + 0.1 Ω)
0201: ± (2 % + 0.1 Ω)
Specifications are subject to change without notice. Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Derating Curve
100
Power Ratio (%)
80
60
70
40
CR0201A
20
125
0
-55
20
40
60
80
100
120
155
140
160
Ambient Temperature (°C)
Packaging Dimensions (Conforms to EIA RS-481A)
Model
CR0201A-AS
CR0402A-AS
Tape Type
Paper Tape
(2 mm
pitch)
CR0603A-AS
CR0805A-AS
CR1206A-AS
Paper Tape
(4 mm
pitch)
CR1210A-AS
CR2010A-AS
CR2512A-AS
Embossed
Tape
(4 mm
pitch)
A
B
0.37 ± 0.05
(.010 ± .002)
0.67 ± 0.10
(.026 ± .004)
0.70 ± 0.05
(.028 ± .002)
1.20 ± 0.05
(.047 ± .002)
1.10 ± 0.10
(.043 ± .004)
1.90 ± 0.10
(.075 ± .004)
1.65 ± 0.15
(.065 ± .006)
2.40 ± 0.20
(.094 ± .008)
2.00 ± 0.15
(.079 ± .006)
3.60 ± 0.20
(.142 ± .008)
2.80 ± 0.20
(.110 ± .008)
3.60 ± 0.20
(.142 ± .008)
2.80 ± 0.20
(.110 ± .008)
5.30 ± 0.20
(.209 ± .008)
3.60 ± 0.20
(.142 ± .008)
6.90 ± 0.20
(.272 ± .008)
W
F
E
P1
2.00 ± 0.10
(.079 ± .004)
8.00 ± 0.20
(.315 ± .008)
P2
T
2.00 ± 0.05
(.079 ± .002)
0.37 ± 0.10
(.015 ± .004)
2.00 ± 0.10
(.079 ± .004)
0.45 ± 0.10
(.018 ± .004)
0.64 ± 0.10
(.025 ± .004)
3.50 ± 0.05
(.138 ± .002)
1.75 ± 0.10
(.069 ± .004)
4.00 ± 0.10
(.157 ± .004)
4.00 ± 0.10
(.157 ± .004)
12.00 ± 0.20
(.472 ± .008)
P0
2.00 ± 0.05
(.079 ± .002)
0.84 ± 0.10
(.033 ± .004)
0.84 ± 0.10
(.033 ± .004)
0.84 ± 0.10
(.033 ± .004)
0.85 ± 0.15
(.033 ± .006)
5.50 ± 0.05
(.217 ± .002)
0.85 ± 0.15
(.033 ± .006)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Packaging Dimensions (Conforms to EIA RS-481A)
PAPER TAPE (2 mm PITCH)
BOTTOM TAPE
1.50 ± 0.10
DIA.
(.059 ± .004)
TOP TAPE
E
F
W
RESISTOR
B
PAPER TAPE
T
P1
A
P2
P0
DIRECTION OF UNREELING
PAPER TAPE (4 mm PITCH)
BOTTOM TAPE
1.50 ± 0.10
DIA.
(.059 ± .004)
TOP TAPE
E
F
W
RESISTOR
B
PAPER TAPE
T
P1
A
P2
P0
DIRECTION OF UNREELING
EMBOSSED TAPE (4 mm PITCH)
EMBOSSED TAPE
1.50
MIN. DIA.
(.059)
TOP TAPE
1.50 ± 0.10
DIA.
(.059 ± .004)
E
F
W
RESISTOR
B
T
A
P1
P2
P0
DIRECTION OF UNREELING
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Packaging Dimensions (Conforms to EIA RS-481A)
W
C DIA.
B DIA.
T
A DIA.
Model
CR0201A-AS
CR0402A-AS
Packaging Quantity
CR1206A-AS
B
C
W
T
178 ± 2.0
(7.008 ± .079)
60 ± 1.0
(2.362 ± .039)
13.0 ± 1.0
(.512 ± .039)
9.0 ± 1.0
(.354 ± .039)
11.5 ± 1.0
(.453 ± .039)
178 ± 2.0
(7.008 ± .079)
60 ± 0.5
(2.362 ± .020)
13.0 ± 0.5
(.512 ± .020)
13.0 ± 1.0
(.512 ± .039)
15.5 ± 1.0
(.610 ± .039)
10K pcs/reel
CR0603A-AS
CR0805A-AS
A
5K pcs/reel
CR1210A-AS
CR2010A-AS
CR2512A-AS
4K pcs/reel
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
How to Order
Model
(CR = Fixed Resistor)
CR 0603 A F X - 1002 E AS
Size
0201 = 0201 size
0402 = 0402 size
0603 = 0603 size
0805 = 0805 size
1206 = 1206 size
1210 = 1210 size
2010 = 2010 size
2510 = 2510 size
Feature
A = AEC-Q200 Compliant
Resistance Tolerance
F = ±1 %
J = ±5 %
TCR (ppm/°C) – See Electrical Characteristics Chart
X = ±100
W = ±200
Z = ±400
/ = Used for zero Ω (jumper) and values from 1 Ω through 9.76 Ω.
Resistance Value
For 1 % Tolerance:
100 Ω ....... First three digits are significant, fourth digit represents number of zeros to follow (example: 8252 = 82.5K Ω).
For 5 % Tolerance:
10 Ω.......... First two digits are significant, third digit represents number of zeros to follow (example: 474 = 470K Ω).
Packaging
G = Paper Tape (10,000 pcs.) on 7 ” Reel – CR0201A-AS, CR0402A-AS
E = Paper Tape (5,000 pcs.) on 7 ˝ Reel – CR0603A-AS, CR0805A-AS, CR1206A-AS, CR1210A-AS
E = Embossed Tape (4,000 pcs) on 7 ˝ Reel – CR2010A-AS, CR2512A-AS
Termination
AS = Anti-sulfur version, Tin-plated (RoHS Compliant)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
CRxxxxA-AS - Sulfur-Resistant, AEC-Q200 Compliant Chip Resistors
Symbol for E96 Series Nominal Resistance Value
Marking Explanation
Symbol
E96
Symbol
E96
Symbol
E96
Symbol
E96
01
100
25
178
49
316
73
562
02
102
26
182
50
324
74
576
03
105
27
187
51
332
75
590
04
107
28
191
52
340
76
604
05
110
29
196
53
348
77
619
06
113
30
200
54
357
78
634
07
115
31
205
55
365
79
649
08
118
32
210
56
374
80
665
09
121
33
215
57
383
81
681
10
124
34
221
58
392
82
698
11
127
35
226
59
402
83
715
12
130
36
232
60
412
84
732
13
133
37
237
61
422
85
750
14
137
38
243
62
432
86
768
15
140
39
249
63
442
87
787
16
143
40
255
64
453
88
806
17
147
41
261
65
464
89
825
18
150
42
267
66
475
90
845
19
154
43
274
67
487
91
866
20
158
44
280
68
499
92
887
21
162
45
287
69
511
93
909
22
165
46
294
70
523
94
931
23
169
47
301
71
536
95
953
24
174
48
309
72
549
96
976
102
±5 % (E24): CR0603-A-AS /
CR0805A-AS / CR1206A-AS /
CR1210A-AS / CR2010A-AS /
CR2512A-AS
Resistance value is expressed by 3
digits. The first two digits represent the
significant figures of nominal resistance
value in Ω. And the third digit represents
exponent for base of 10.
EX: 102 = 10 x 102 = 1000 Ω = 1K Ω
±1 % (E96): CR0805A-AS /
CR1206A-AS / CR1210A-AS /
CR2010A-AS / CR2512A-AS
Resistance value is expressed by 3
digits. The first two digits represent the
significant figures of nominal resistance
value in Ω. And the third digit represents
exponent for base of 10.
EX: 102 = 10 x 102 = 1000 Ω = 1K Ω
01A
±1 % (E96): CR0603A-AS
When the marking space is too small in
such small-sized resistors as CR0603AAS, the marking cannot be made by 4
digits and may be made by two digits
combined with one English capital.
EX: 01A = 100 x 100 = 100 Ω
Symbol for Multipliers
Symbol
A
Multiplier
10
B
0
10
C
1
10
D
2
10
E
3
10
F
4
10
G
5
10
H
6
10
7
X
Y
Z
10
10
10-3
-1
-2
Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
05/19
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and its
affiliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information and verify that such information is current and
complete before placing orders for Bourns® products.
The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary
from the data sheet characteristics and parameters due to (i) the combination of the Bourns® product with other components
in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns®
product also can and do vary in different applications and actual performance may vary over time. Users should always verify
the actual performance of the Bourns® product in their specific devices and applications, and make their own independent
judgments regarding the amount of additional test margin to design into their device or application to compensate for
differences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns® product to meet the requirements of such industry standard or particular qualification. Users of
Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to their
devices or applications.
Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or
environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives on a
case-by-case basis, use of any Bourns® products in such unauthorized applications might not be safe and thus is at the user’s
sole risk. Life-critical applications include devices identified by the U.S. Food and Drug Administration as Class III devices and
generally equivalent classifications outside of the United States.
Bourns expressly identifies those Bourns® standard products that are suitable for use in automotive applications on such
products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive
application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns
expressly identifies a sub-category of automotive application in the data sheet for its standard products (such as infotainment
or lighting), such identification means that Bourns has reviewed its standard product and has determined that if such Bourns®
standard product is considered for potential use in automotive applications, it should only be used in such sub-category of
automotive applications. Any reference to Bourns® standard product in the data sheet as compliant with the AEC-Q standard
or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application.
Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns expressly identifies Bourns® standard products that are suitable for use in aircraft
or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically
approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard
product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at the
user’s sole risk.
The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns and
the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns and the
user regarding the use and level of such testing, the above provisions applicable to Bourns® standard products shall also apply
to such Bourns® custom products.
Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns® products and Bourns technology and technical data may not under any circumstance be
exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without prior
authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible
to receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential,
incidental or indirect damages or lost revenues or lost profits, and (ii) any and all implied warranties, including implied warranties
of fitness for particular purpose, non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese
bilingual versions are available at:
Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies
PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf
C1753 05/17/18R
工商网监
湘ICP备2023018690号
