CRA2512-FZ-R010ELF.

& *R AE oH C- S C Q2 O 00 MP Q LI UA AN LI T FI ED Features Applications n Special alloy resistor n Power supplies n Power rating at 70 °C: 3 W n Stepper motor drives n Inductance less than 5 nH n Input amplifiers 10 R0 n RoHS compliant* AP *Ro PR HS OV C ED OM (S PL el IAN ec T t M od el s) n AEC-Q200 qualified, automotive grade CRA2512 - High Power Current Sense Chip Resistor AE C Electrical Characteristics Recommended Solder Pad Layout Characteristic L CRA2512 Power Rating @ 70 °C 3W Operating Temperature Range -55 °C to +170 °C Derated to Zero Load at +170 °C Maximum Working Current (P / R)1/2 Insulation Resistance > 100 megohms Resistance Range A Cu TRACE 0.010 - 0.100 Ω Resistance Tolerance ±1 %, ±5 % Temperature Coefficient ±50 PPM/°C SENSING TRACE Model A B L CRA2512 4.0 2.1 4.1 (0.157) (0.083) (0.161) Performance Characteristics Test Thermal Shock Short Time Overload Low Temperature Storage High Temperature Exposure Bias Humidity Mechanical Shock Vibration Load Life Resistance to Solder Heat Moisture Resistance B DIMENSIONS: Conditions -55 ˚C to + 150 ˚C, 1000 Cycles, 15 minutes 5 X Rated Power for 5 seconds Specification -55 ˚C for 24 hours ΔR < ±0.5 % 1000 hours @ + 170 ˚C ΔR < ±1.0 % + 85 ˚C, 85 % RH, 10 % Bias, 1000 hours 100 g’s for 6 milliseconds, 5 pulses Frequency varied 10 to 2000 KHz in one minute, 3 directions, 12 hours 1000 hours at rated power at +70 ˚C, 1.5 hours on, 0.5 hours off +260 ˚C Solder, 10-12 second dwell, 25 mm/second emergence MIL-STD-202 Method 106, 0 % power (7a and 7b not required) ΔR < ±0.5 % MM (INCHES) Construction ΔR < ±0.5 % Overcoat ΔR < ±0.5 % Ni / Sn Plating Metal Alloy Plate ΔR < ±0.5 % ΔR < ±0.5 % ΔR < ±1.0 % ΔR < ±0.5 % ΔR < ±0.5 % Product Dimensions A T B C C C C Resistor Model A B C T Material 6.45 ± 0.20 3.35 ± 0.20 0.95 ± 0.10 0.7 ± 0.20 Resistor Cu-Ni CRA2512 or Cu-Mn (0.254 ± 0.008) (0.131 ± 0.008) (0.037 ± 0.004) (0.0276 ± 0.008) *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. DIMENSIONS: MM (INCHES) EMBOSSED TAPE 1.5 (0.059) DIA. MIN. 1.5 +0.1/-0 DIA. (0.059 +0.004/-0) TOP TAPE 1.75 ± 0.1 (0.069 ± 0.004) 5.5 ± 0.05 (0.217 ± 0.002) 12.0 ± 0.2 (0.472 ± 0.008) 6.9 ± 0.2 (0.272 ± 0.008) 4.0 ± 0.05 (0.157 ± 0.002) RESISTOR CRA2512 - High Power Current Sense Chip Resistor 3.60 ± 0.20 (0.142 ± 0.008) 1.2 ± 0.15 (0.047 ± 0.006) 2.0 ± 0.05 (0.079 ± 0.002) 4.0 ± 0.1 (0.157 ± 0.004) USER DIRECTION OF FEED Packaging Dimensions (Conforms to EIA RS-481A) EMBOSSED TAPE 1.5 (0.059) DIA. MIN. 1.5 +0.1/-0 DIA. (0.059 +0.004/-0) TOP TAPE 1.75 ± 0.1 (0.069 ± 0.004) 5.5 ± 0.05 (0.217 ± 0.002) 13.0 ± 1.0 (0.512 ± 0.039) DIA. 180 +0/-3 (7.09 +0/-0.118) DIA. 12.0 ± 0.2 (0.472 ± 0.008) 6.9 ± 0.2 (0.272 ± 0.008) 4.0 ± 0.05 (0.157 ± 0.002) RESISTOR 3.60 ± 0.20 (0.142 ± 0.008) 1.2 ± 0.15 (0.047 ± 0.006) 4.0 ± 0.1 (0.157 ± 0.004) 60.0 (2.362) MIN. DIA. 2.0 ± 0.05 (0.079 ± 0.002) USER DIRECTION OF FEED DIMENSIONS: Code Can be soldered in accordance with IPC/JEDEC-J-STD-020. 13.0 ± 1.0 R Value (0.512 ± 0.039) 0.010 R050 0.050 R015 0.015 R060 0.060 R020 0.020 R070 0.070 R025 0.025 R075 0.075 R030 0.030 R080 0.080 R040 0.040 R100 0.100 DIA. Consult factory for other resistance values. Maximum of 20 seconds between +255 °C and +260 °C 180 +0/-3 (7.09 +0/-0.118) DIA. 225 60.0 (2.362) 190 °C MIN. DIA. 175 13.0 ± 1.0 (0.512 ± 0.039) 125 70 170 60 - 120 seconds 10 seconds minimum Ramp Up 3 °C/second maximum 0 50 100 150 Time (seconds) 200 250 300 How to Order REV. 01/17 90 - 150 seconds 75 25 Ambient Temperature (°C) 220 °C Ramp Down 6 °C/second 100 -55 260 °C peak 255 °C 150 °C 15.4 ± 2.0 (0.606 ± 0.079) Derating Curve Power Ratio (%) 275 Temperature (°C) R010 R Value 13.0 ± 1.0 (0.512 ± 0.039) Soldering Profile CRA2512 Resistance Values Available Code 15.4 ± 2.0 (0.606 ± 0.079) MM (INCHES) CRA 2512 - F Z - R020 E LF Model (CRA = Precision Chip Resistor Size 2512 = 2512 Size Resistance Tolerance • F = ±1 % • J = ±5 % TCR (PPM/°C) • Z = ±50 PPM/°C Resistance Value “R” (decimal point) followed by three significant digits (example: R025 = 0.025 ohm) Packaging • E = 4000 pieces on 180 mm (7 inch) reel Termination • LF = Tin-plated (RoHS compliant) Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications.