MF-R015/600-2-V7

Features This series is currently available but not recommended for new designs. n Radial Leaded Devices n Maximum 600 VAC interrupt fault rating n Available in matched resistance “bins” n Ability to withstand lightning surges n RoHS compliant* n Ability to withstand AC power cross conditions n Agency recognition: MF-R/600 Series - Telecom PTC Resettable Fuses Electrical Characteristics Model Max. Operating Voltage (VDC) MF-R015/600 MF-R015/600-A MF-R015/600-B MF-R015/600-F MF-R016/600 MF-R016/600-A MF-R016/600-1 250 250 250 250 250 250 250 Max. Interrupt Ratings Volts Amps Max. 600 600 600 600 600 600 600 Max. 3 3 3 3 3 3 3 Hold Current Trip Current Amps at 23 °C Amps at 23 °C 0.15 0.15 0.15 0.15 0.16 0.16 0.16 0.30 0.30 0.30 0.30 0.32 0.32 0.32 Initial Resistance Ohms at 23 °C Min. 6.0 7.0 9.0 7.0 4.0 4.0 4.0 Ohms at 23 °C Max. 12.0 10.0 12.0 12.0 10.0 7.0 8.0 Tripped One Hour Max. Time Power Post-Trip To Trip @ 1A Dissipation Resistance Ohms Seconds Watts at 23 °C at 23 °C at 23 °C Max. 22.0 5.0 1.0 20.0 5.0 1.0 22.0 5.0 1.0 22.0 5.0 1.0 18.0 7.0 1.0 16.0 7.0 1.0 17.0 7.0 1.0 Environmental Characteristics Operating/Storage Temperature............................ -40 °C to +85 °C Maximum Device Surface Temperature in Tripped State.................................................. 125 °C Passive Aging........................................................ +60 °C, 1000 hours................................................ ±15 % typical resistance change Humidity Aging...................................................... +60 °C, 90 % R.H. 1000 hours.............................. ±15 % typical resistance change Solvent Resistance................................................ MIL-STD-202, Method 215B.................................. No change Lead Solderability.................................................. ANSI/J-STD-002 Flammability.......................................................... IEC 695-2-2........................................................... No flame for 60 secs. Vibration................................................................ MIL-STD-883C, Method 2007.1, Condition A........ No change Test Procedures And Requirements For Model MF-R/600 Series Test Test Conditions Accept/Reject Criteria Visual/Mech........................................................... Verify dimensions and materials............................ Per MF physical description Resistance............................................................. In still air @ 23 °C.................................................. Rmin ≤ R ≤ Rmax Time to Trip............................................................ 1 A, Vmax, 23 °C................................................... T ≤ max. time to trip (seconds) Hold Current.......................................................... 30 min. at Ihold...................................................... No trip Trip Cycle Life........................................................ Vmax, Itrip, 100 cycles........................................... No arcing or burning Trip Endurance...................................................... Vmax, 24 hours...................................................... No arcing or burning UL File Number..................................................... E307915 TÜV File Number................................................... R 50256529 Thermal Derating Chart - Ihold (Amps) Model Ambient Operating Temperature -40 °C -20 °C 0 °C 23 °C 40 °C 50 °C 60 °C 70 °C 85 °C MF-R015/600 0.233 0.206 0.178 0.150 0.124 0.110 0.096 0.083 0.062 MF-R016/600 0.249 0.219 0.190 0.160 0.132 0.117 0.103 0.088 0.066 Itrip is approximately two times Ihold. WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Applications Customer Premise Equipment (CPE): n Modems n Cable modems n Fax machines n POS equipment n Security equipment n Set top boxes MF-R/600 Series - Telecom PTC Resettable Fuses Product Dimensions A Max. 13.5 (0.531) 16.0 (0.629) Model MF-R015/600 MF-R016/600 B Max. 12.6 (0.496) 12.6 (0.496) Packaging options: BULK: 300 pcs. per bag. Longer lead lengths available upon request. A D Min. 4.7 (0.185) 4.7 (0.185) TAPE & REEL: 600 pcs. per reel. DIMENSIONS: MANUFACTURER'S TRADEMARK PART IDENTIFICATION R015 DATE CODE (FIRST DIGIT = LAST DIGIT OF YEAR; SECOND DIGIT = MONTH; NEXT THREE DIGITS = LOT CODE) 24001K MFG. LOCATION (K = KOREA S = CHINA T = TAIWAN) Typical Time to Trip at 23 ˚C Time to Trip (Seconds) 1000 100 MM (INCHES) How to Order Represents total content. Layout may vary. E Physical Characteristics Style Lead Dia. Material 0.65 1 Sn/Cu (0.026) 0.65 1 Sn/Cu (0.026) E Nom. 5.0 (0.197) 5.0 (0.197) Typical Part Marking C B D C Max. 6.0 (0.236) 6.0 (0.236) MF-R016/600 MF-R015/600 MF - R 015/600 - A 05 - 2 Multifuse Product Designator Series R = Radial Leaded Component Hold Current, Ihold 015-016 (0.15 - 0.16 Amps) Max. Interrupt Voltage, V Resistance Range • Narrow resistance ranges are available on all models as defined in Electrical Characteristics. • Blank = N/A Resistance Bins • Narrow resistance ranges can be separated into packages where each device is within 0.5 ohms of each other. • Blank = N/A Packaging Options - 0 = Bulk Packaging - 2 = Tape and Reel* *Packaged per EIA486-B ® 10 1 0.10 0.00 0.50 1.00 1.50 2.00 2.50 3.00 Fault Current (Amps) Resistance Options Model MF-R015/600 MF-R015/600-A MF-R015/600-B MF-R015/600-F MF-R016/600 MF-R016/600-A MF-R016/600-1 MF-R/600, REV. O, 03/19 Rmin. 6.0 7.0 9.0 7.0 4.0 4.0 4.0 Rmax. 12.0 10.0 12.0 12.0 10.0 7.0 8.0 R1Max. 22.0 20.0 22.0 22.0 18.0 16.0 17.0 Bin N/A 0.5 0.5 0.5 N/A 0.5 0.5 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.  MF-R, MF-R/90, MF-R/600, & MF-RX, & MF-RX/72 Series Tape and Reel Specifications Devices taped using EIA468–B/IEC286-2 standards. See table below and Figures 1 and 2 for details. Dimension Description EIA Dimensions Mark Dimensions Tolerance 18 -0.5/+1.0 Carrier tape width W W (.709) (-0.02/+.039) 11 Hold down tape width W4 min. W0 (.433) Hold down tape IEC Mark No protrusion 3 Top distance between tape edges W2 W6 max. (.118) 9 -0.5/+0.75 Sprocket hole position W1 W5 (.354) (-0.02/+0.03) 4 ±0.2 Sprocket hole diameter D0 D0 (.157) (±.0078) 18.5 ±3.0 Abscissa to plane (straight lead) H H (.728) (±.118) 16 ±0.5 Abscissa to plane (kinked lead) H0 H0 (.63) (±.02) 38.0 Abscissa to top (straight lead) H1 H1 max. (1.496) 32.2 Abscissa to top (kinked lead) H1 H1 max. (1.268) 55.0 Overall width w/lead protrusion (straight lead) C1 max. (2.165) 43.2 Overall width w/lead protrusion (kinked lead) C1 max. (1.7) 54.0 Overall width w/o lead protrusion (straight lead) C2 max. (2.126) 42.5 Overall width w/o lead protrusion (kinked lead) C2 max. (1.673) 1.0 Lead protrusion I1 L1 max. (.039) 11 Protrusion of cutout L L max. (.433) Protrusion beyond hold-down tape I2 I2 Not specified 12.7 ±0.3 (0.5) (±.012) ±1 Pitch tolerance 20 consecutive (±.039) Sprocket hole pitch P0 P0 Device pitch: MF-R005–MF-R160, MF-R/90, 12.7 ±0.3 MF-RX020/72–MF-RX030/72 (0.5) (±.012) Device pitch: MF-R185–MF-R400, MF-R/600, MF-RX110–MF-RX375 25.4 ±0.6 MF-RX040/72–MF-RX375/72 (1.0) (±.024) 0.9 Tape thickness t t max. (.035) Tape thickness with splice: MF-R010–MF-R160, t1 1.5 max. MF-RX110/72–MF-RX185/72 (.059) Tape thickness with splice: MF-R250–MF-R1100, t1 2.3 max. MF-RX110–MF-RX375, MF-R/90, MF-RX250/72-MF-RX375/72 (.091) ±0.3 Splice sprocket hole alignment 0 (±.012) ±1.0 Body lateral deviation Δh Δh 0 (±.039) ±1.3 Body tape plane deviation Δp Δp 0 (±.051) DIMENSIONS: MM (INCHES) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.  MF-R, MF-R/90, MF-R/600, MF-RX, & MF-RX/72 Series Tape and Reel Specifications Dimension Description IEC Mark EIA Dimensions Mark Dimensions Tolerance 5.08 ±0.2 Lead spacing: MF-R, MF-R/90, MF-R/600, MF-RX, MF-RX/72 F F (0.2) (±0.008) 56.0 Reel width w W2 max. (2.205) 370.0 Reel diameter d a max. (14.57) 4.75 ±3.25 Space between flanges less device W1 h (.187) (±.128) 26.0 ±12.0 Arbor hole diameter f c (1.024) (±.472) 80 Core diameter: MF-R, MF-RX, MF-R/90 h n max. (3.15) 91 Core diameter: MF-R/600 h n max. (3.58) 62 355 345 Box: MF-R, MF-RX, MF-R/90 nom. (2.44) (14.0) (13.6) 64 372 362 Box: MF-R/600 max. (2.52) (14.6) (14.25) p h h MF-R, MF-RX, Consecutive missing places: MF-R/90 Consecutive missing places: MF-R/600 Empty places per reel: MF-R, MF-RX, MF-R/90 P1 H1 Reference plane L Taped Component Dimensions Figure 1 H0 B Not specified H1 H 0.1 % W1 W0 W p h h I2 P0 I1 A I1 B P0 H0 W0 D0 p User direction of feed Cross section A - B H1 H F L I2 D0 Reference plane P1 H1 max. none F Empty places per reel: MF-R/600 A p 3 W1 t W User direction of feed Cross section A - B Reel Dimensions - Figure 2 t Reel Upper side Tape h d User direction of feed Lower side f h w Reel DIMENSIONS: MM (INCHES) Upper side h Tape Specifications are subject to change without notice. User Users should verify actual device performance in their specific applications. direction d The products described herein and this document are subject to specific legal disclaimers as set of forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. feed Lower side  Bourns PPTC Resettable Fuses 3312 - ®2 Multifuse mm SMD® Trimming Potentiometer Application Notice • Users are responsible for independent and adequate evaluation of Bourns® Multifuse® Polymer PTC devices in the user’s application, including the PPTC device characteristics stated in the applicable data sheet. • Polymer PTC devices must not be allowed to operate beyond their stated maximum ratings. Operation in excess of such maximum ratings could result in damage to the PTC device and possibly lead to electrical arcing and/or fire. Circuits with inductance may generate a voltage above the rated voltage of the polymer PTC device and should be thoroughly evaluated within the user’s application during the PTC selection and qualification process. • Polymer PTC devices are intended to protect against adverse effects of temporary overcurrent or overtemperature conditions up to rated limits and are not intended to serve as protective devices where overcurrent or overvoltage conditions are expected to be repetitive or prolonged. • In normal operation, polymer PTC devices experience thermal expansion under fault conditions. Thus, a polymer PTC device must be protected against mechanical stress, and must be given adequate clearance within the user’s application to accommodate such thermal expansion. Rigid potting materials or fixed housings or coverings that do not provide adequate clearance should be thoroughly examined and tested by the user, as they may result in the malfunction of polymer PTC devices if the thermal expansion is inhibited. • Exposure to lubricants, silicon-based oils, solvents, gels, electrolytes, acids, and other related or similar materials may adversely affect the performance of polymer PTC devices. • Aggressive solvents may adversely affect the performance of polymer PTC devices. Conformal coating, encapsulating, potting, molding, and sealing materials may contain aggressive solvents including but not limited to xylene and toluene, which are known to cause adverse effects on the performance of polymer PTCs. Such aggressive solvents must be thoroughly cured or baked to ensure their complete removal from polymer PTCs to minimize the possible adverse effect on the device. • Recommended storage conditions should be followed at all times. Such conditions can be found on the applicable data sheet and on the Multifuse® Polymer PTC Moisture/Reflow Sensitivity Classification (MSL) note: https://www.bourns.com/docs/RoHS-MSL/msl_mf.pdf MFAN 12/18 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.  Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and its affiliates (collectively, “Bourns”). Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change without notice. Users should check for and obtain the latest relevant information and verify that such information is current and complete before placing orders for Bourns® products. The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary from the data sheet characteristics and parameters due to (i) the combination of the Bourns® product with other components in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns® product also can and do vary in different applications and actual performance may vary over time. Users should always verify the actual performance of the Bourns® product in their specific devices and applications, and make their own independent judgments regarding the amount of additional test margin to design into their device or application to compensate for differences between laboratory and real world conditions. Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any failure of an individual Bourns® product to meet the requirements of such industry standard or particular qualification. Users of Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to their devices or applications. Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any Bourns® products in such unauthorized applications might not be safe and thus is at the user’s sole risk. Life-critical applications include devices identified by the U.S. Food and Drug Administration as Class III devices and generally equivalent classifications outside of the United States. Bourns expressly identifies those Bourns® standard products that are suitable for use in automotive applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns expressly identifies a sub-category of automotive application in the data sheet for its standard products (such as infotainment or lighting), such identification means that Bourns has reviewed its standard product and has determined that if such Bourns® standard product is considered for potential use in automotive applications, it should only be used in such sub-category of automotive applications. Any reference to Bourns® standard product in the data sheet as compliant with the AEC-Q standard or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application. Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally or any other generally equivalent governmental organization standard applicable to products designed or manufactured for use in aircraft or space applications. Bourns expressly identifies Bourns® standard products that are suitable for use in aircraft or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns and the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns and the user regarding the use and level of such testing, the above provisions applicable to Bourns® standard products shall also apply to such Bourns® custom products. Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions apply to all uses and applications that violate national or international prohibitions, including embargos or international regulations. Further, Bourns® products and Bourns technology and technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without prior authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible to receive U.S. commodities, software, and technical data. To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential, incidental or indirect damages or lost revenues or lost profits, and (ii) any and all implied warranties, including implied warranties of fitness for particular purpose, non-infringement and merchantability. For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese bilingual versions are available at: Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf C1753 05/17/18R