PDB182-GTRB1-504MN

PL IA N T Features CO M ■ Carbon element *R oH S ■ Plain or knurled shaft option ■ Metal bushing/metal shaft ■ Center detent standard ■ Rear solder lugs or PC pins ■ 250K and 500K standard resistance values ■ RoHS compliant* ■ Standard M and N taper PDB182-GTRB - 17 mm Blend-Balance Guitar Potentiometer Product Dimensions Electrical Characteristics Taper...................................... Linear, audio Standard Resistance Range ............................... 250K to 500K ohms Standard Resistance Tolerance....... ±20 % Residual Resistance ................... 1 % max. PDB182-GTRB3, PDB182-GTRB4 PDB182-GTRB1, PDB182-GTRB2 11.3 (.445) 9.5 (.374) 19.0 (.748) 1.0 1.5 (.059) (.039) 6.00 (.236) DIA. Environmental Characteristics Operating Temperature.... -10 °C to +50 °C Power Rating Dual Section ............................ 0.06 watt Maximum Operating Voltage Audio .............................................150 V Sliding Noise ...........................47 mV max. KNURLED SHAFT 13.00 (.512) 19.0 (.748) 9.5 (.374) 16.5 (.650) 1.5 (.059) 14.8 (.583) 3/8”NEF 1.5 (.059) 3.0 (.118) PLAIN SHAFT 6.0 (.236) DIA. C0.5 18 TEETH R1 R2 DIA. 6.00 (.236) 1.0 (.039) KNURLED SHAFT R1 7.7 (.303) 6.0 (.236) 11.5 (.453) C0.5 18 TEETH 3/8”NEF R2 Mechanical Characteristics Mechanical Angle .......................300 ° ±5 ° Rotational Torque ............. 10 to 150 gf-cm Detent Torque ................... 50 to 300 gf-cm Stop Strength ........................5 kg-cm min. Rotational Life ......................15,000 cycles Soldering Condition Manual/Wave ........... 260 °C max. for 3 seconds max. Wash.........................Not recommended Hardware .................... One flat washer and mounting nut supplied per potentiometer with bushing 11.3 (.445) 6.0 (.236) 5.0 (.197) 16.2 (.638) 1.0 (0.39) 2.5 (.098) 3.5 (.138) 5.0 (.197) 17.0 DIA. (.669) 17.0 DIA. (.669) FULL CW 30 °±10 ° FULL CW POSITION 30 °±10 ° Standard Resistance Table Resistance (Ohms) 250,000 500,000 13.00 (.512) Resistance Code 254 504 5.0 (.197) How to Order 1 NUT 2 3 5.0 (.197) 3/8”NEF PDB18 2 - GTR B1 - 254 MN 9.7 ± 0.3 (.382 ± .012) DIA. WASHER 5.0 (.197) 1 2 3 5.0 (.197) Model Number of Sections 2 = Dual Section Guitar Pot Designator Configuration B1 = Knurled Shaft/Solder Lugs/ Center Detent B2 = Plain Shaft/Solder Lugs/ Center Detent B3 = Knurled Shaft/PC Pins/ Center Detent B4 = Plain Shaft/PC Pins/ Center Detent 11.0 ± 0.5 (.433 ± .020 2.3 ± 0.2 (.091 ± .008) 12.0 ± 0.5 DIA. (.472 ± .020) UNDER TOLERANCES: ±0.3 10.0 ±0.5 10.0 ~ 100 = = (.394) (±.012) (.394 ~ 3.937) (±.020) Resistance Code (See Table) Resistance Taper (See Taper Chart) WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. PDB182-GTRB - 17 mm Blend-Balance Guitar Potentiometer Taper Chart Rating Power Ratio (%) Derating Curve M and N Taper 100 N(2H) M(1H) 90 Taper N: Output voltage across term. 2-3 X 100 (%) Input voltage across term. 1-3 Taper M: Output voltage across term. 1-2 X 100 (%) Input voltage across term. 1-3 80 70 60 M(1H) N(2H) 50 Circuit Dual Gang 2 100 80 R1 1 3 60 40 33 20 0 R2 1’ 3’ 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (°C) 2’ 40 30 20 10 0 10 Term “1” 20 30 40 50 60 Rotational Travel (%) 70 80 90 100 Term “3” NOTE: Resistance characteristic of curve N is plotted with respect to terminal “3” Asia-Pacific: Tel: +886-2 2562-4117 • Email: asiacus@bourns.com EMEA: Tel: +36 88 885 877 • Email: eurocus@bourns.com The Americas: Tel: +1-951 781-5500 • Email: americus@bourns.com www.bourns.com REV. 10/19 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and P[ZHɉSPH[LZJVSSLJ[P]LS`¸)V\YUZ¹ Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change ^P[OV\[UV[PJL