PM610-05

Muilt - 6 Pack, Inductors and Transformers PM600 / PM610 / PM620 Series Special Features: • Six windings offer many inductor or transformer configuration • High magnetic coupling • Non-gapped and gapped core construction • Low core loss at high frequency applications • Low noise radiation • Compact size and low profile • Dielectric strength: 500 Vrms between windings • Operating temperature: -40 to +105 ºC • Tape & Reel packaging: PM600, 600/reel PM610, 300/reel PM620, 200/reel Typical Applications: • Inductors: buck, boost, buck-boost, coupled, input, output, choke, filter, resonant, high-Q, EMI/RFI filtering, differential, forward, common mode • Transformers: flyback, forward, push-pull, bridge, multiple outputs, inverter, step-up, step-down, gate drive, base drive, signal, wide band, pulse, impedance, isolation, converter Notes: 1. Saturation current is rated to each winding that causes inductance to drop 30% from its initial value. 2. Rms current is rated to each winding that causes 40°C temperature rise. 3. PM600-01, -02, PM610-01, -02 PM620-01, -02 are non gap core. Part Number PM600-01 PM600-02 PM600-03 PM600-04 PM600-05 PM600-06 PM600-07 PM600-08 PM600-09 PM600-10 PM610-01 PM610-02 PM610-03 PM610-04 PM610-05 PM610-06 PM610-07 PM610-08 PM610-09 PM610-10 PM620-01 PM620-02 PM620-03 PM620-04 PM620-05 PM620-06 PM620-07 PM620-08 PM620-09 PM620-10 PM620-11 PM620-12 L (uH) @ 100KHz 201.6 ±30% 89.6 ±30% 27.4 ±10% 12.2 ±10% 14.7 ±10% 6.5 ±10% 10.9 ±10% 4.9 ±10% 8.5 ±10% 3.8 ±10% 160.0 ±30% 78.4 ±30% 21.6 ±10% 10.6 ±10% 11.6 ±10% 5.7 ±10% 8.3 ±10% 4.1 ±10% 6.6 ±10% 3.2 ±10% 160.6 ±30% 77.0 ±30% 131.8 ±20% 63.2 ±20% 23.3 ±10% 11.2 ±10% 14.2 ±10% 6.8 ±10% 9.3 ±10% 4.5 ±10% 7.9 ±10% 3.8 ±10% DCR (Ω) Max. 0.324 0.137 0.324 0.137 0.324 0.137 0.324 0.137 0.324 0.137 0.202 0.094 0.202 0.094 0.202 0.094 0.202 0.094 0.202 0.094 0.094 0.065 0.094 0.065 0.094 0.065 0.094 0.065 0.094 0.065 0.094 0.065 Isat (A) 0.02 0.03 0.31 0.47 0.58 0.87 0.88 1.32 1.23 1.85 0.04 0.06 0.67 0.96 1.30 1.86 2.00 2.86 2.30 3.29 0.03 0.04 0.08 0.12 0.36 0.52 0.76 1.10 1.11 1.60 1.40 2.02 J.W.Miller M A G N E T I C S 306 E. Alondra Blvd., Gardena, CA 90247-1059 • (310) 515-1720 • FAX (310) 515-1962 www.jwmiller.com Irms (A) 0.46 0.71 0.46 0.71 0.46 0.71 0.46 0.71 0.46 0.71 0.68 1.00 0.68 1.00 0.68 1.00 0.68 1.00 0.68 1.00 1.28 1.54 1.28 1.54 1.28 1.54 1.28 1.54 1.28 1.54 1.28 1.54 Mechanical Dimensions: (mm) Mark Pin #1 12 1.0 Typ. 0.7 Typ. PM600-01 1 12.7 10 1 5 7 11 2 6 8 12 3 9 2.0 Typ. 2.0 Typ. 6 4 7 10.0 13.2 6.2 Max. Pad Layout PM600-xx 0.25 9.2 11.0 12.2 PM600-xx Mark Pin #1 12 1 1.5 Typ. PM610-01 0.7 Typ. 15.0 2.5 Typ. 2.5 Typ. 6 7 4 10 1 5 7 11 2 6 8 12 3 9 13.6 17.0 7.8 Max. Pad Layout 0.35 12.0 14.6 16.0 PM610-xx Mark Pin #1 12 0.7 Typ. 1.5 Typ. 1 12 6 7 PM620-01 1 17.0 2.5 Typ. 6 2.5 Typ. 7 17.1 22.4 8.4 Max. 0.40 Pad Layout 15.0 18.1 21.4 PM6200-xx J.W.Miller M A G N E T I C S 306 E. Alondra Blvd., Gardena, CA 90247-1059 • (310) 515-1720 • FAX (310) 515-1962 www.jwmiller.com Typical Configurations Inductor Basic Diagram Inductance: L Current: I Figure 1 Inductance: 36 x L Current: I Figure 2 Inductance: 25 x L Current: I Figure 3 Inductance: 16 x L Current: I Figure 4 Inductance: 9 x L Current: 2xI Figure 5 Inductance: 4 x L Current: 3xI Figure 6 Inductance: L Current: 6 x I Transformer Basic Diagram Turns ratio: 1:1:1:1:1:1 Figure 2 Turns ratio: 1:1 Figure 2 Turns ratio: 1:1:1 Figure 3 Turns ratio: 1:5 or 5:1 Figure 4 Turns ratio: 1:4 or 4:1 Figure 5 Turns ratio: 1:3 or 3:1 Figure 6 Turns ratio: 1:2 or 2:1 Figure 7 Turns ratio: 4:1:1 Figure 8 Turns ratio: 3:1:1:1 Figure 9 Turns ratio: 2:3 or 3:2 J.W.Miller M A G N E T I C S 306 E. Alondra Blvd., Gardena, CA 90247-1059 • (310) 515-1720 • FAX (310) 515-1962 www.jwmiller.com