T
PL
IA
N
M
CO
Features
Applications
■ 6 kA, 8/20 µs surge capability
■ High power DC bus protection
*R
oH
S
■ Low clamping voltage under surge
■ Bidirectional TVS
■ Excellent performance over temperature
PTVS6-xxxC-TH Series High Current TVS Diodes
General Information
The Model PTVS6-xxxC-TH Series high current bidirectional TVS diodes are designed
for use in high power DC bus clamping applications. These devices offer bidirectional
port protection and are available with standoff voltage ratings of 58 V and 76 V.
The devices are RoHS* compliant. They also meet IEC 61000-4-5 8/20 μs current
surge requirements.
Absolute Maximum Ratings (@ TA = 25 °C Unless Otherwise Noted)
Rating
PTVS6-058C-TH
PTVS6-076C-TH
Repetitive Standoff Voltage
Peak Current Rating per 8/20 μs IEC 61000-4-5
Symbol
Value
Unit
VWM
58
76
V
IPPM
6
kA
Operating Junction Temperature Range
TJ
-55 to +125
°C
Storage Temperature Range
TS
-55 to +150
°C
260
°C
Lead Temperature, Soldering (10 s)
Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted)
Parameter
ID
Test Conditions
Standby Current
Clamping Voltage (1) per IEC61000-4-5
(8/20 μs current waveform)
IBR = 10 mA
PTVS6-058C-TH
PTVS6-076C-TH
IPP = 6 kA
PTVS6-058C-TH
PTVS6-076C-TH
V(BR) Temperature Coefficient
C
Capacitance
Typ.
Max.
Unit
10
μA
64
85
66
92
70
95
V
110
140
V
VD = VWM
V(BR) Breakdown Voltage
VC
Min.
F = 10 kHz,
Vd = 1 Vrms
PTVS6-058C-TH
PTVS6-076C-TH
0.1
%/°C
4.5
3.3
nF
(1) V measured at the time which is coincident with the peak surge current.
C
Asia-Pacific: Tel: +886-2 2562-4117 • Fax: +886-2 2562-4116
EMEA: Tel: +36 88 520 390 • Fax: +36 88 520 211
The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700
www.bourns.com
*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
PTVS6-xxxC-TH Series High Current TVS Diodes
Performance Graphs
Percentage VBR Change vs. Junction Temperature
VBR Change vs. Temperature (%)
V-I Characteristic
12
10
8
Normalized to 25 °C
6
4
2
0
-2
-4
-6
-8
-10
-12
-40
-20
0
20
40
-60
-80
100
120
140
Junction Temperature (°C)
Typical Surge Current Derating
Percent of Rated Value
120
110
100
90
80
70
60
50
40
30
20
10
0
0
25
50
75
100
125
150
175
Ambient Temperature (°C)
This graph shows the typical device surge current derating
versus ambient temperature when subjected to the 8/20 µs
current waveform per the IEC 61000-4-5 specification.
This device is not intended for continuous operation at
temperatures above 125 °C.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
PTVS6-xxxC-TH Series High Current TVS Diodes
Product Dimensions
Epoxy encapsulation materials conform to UL 94V-0. Silver plated lead finish conforms to the solderability requirements of JESD22-B102,
Pb free solder. Package dimensions are shown below:
G
Dim.
F
A
B
D
C
C
D
H
E
B
F
E
A
DIMENSIONS:
MM
(INCHES)
G
H
Typical Part Marking
PTVS6-058C-TH .......................................................................6058
PTVS6-076C-TH .......................................................................6076
PTVS6-058C-TH
PTVS6-076C-TH
24.15 ± 0.72
(0.951 ± 0.028)
2.40 ± 0.50
(0.094 ± 0.020)
1.75 ± 1.25
(0.069 ± 0.049)
12.00
Max.
(0.472)
1.25 ± 0.05
(0.049 ± 0.002)
11.50
Max.
(0.453)
5.00
6.00
Max.
Max.
(0.197)
(0.236)
6.00 ± 1.00
(0.236 ± 0.039)
How to Order
PTVS 6 - 076 C - T H
Series
PTVS = Power TVS High Current Diode
Peak Current Rating
6 = 6 kA
Repetitive Standoff Voltage
058 = 58 V
076 = 76 V
Suffix
C = Bidirectional Device
Package
T = Through-Hole
Temperature
H = High Temperature Series
REV. 11/15
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and
its affiliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information and verify that such information is current
and complete before placing orders for Bourns® products.
The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary
from the data sheet characteristics and parameters due to (i) the combination of the Bourns® product with other components
in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns®
product also can and do vary in different applications and actual performance may vary over time. Users should always verify
the actual performance of the Bourns® product in their specific devices and applications, and make their own independent
judgments regarding the amount of additional test margin to design into their device or application to compensate for
differences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns® product to meet the requirements of such industry standard or particular qualification. Users
of Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to
their devices or applications.
Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining
applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property
or environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives
on a case-by-case basis, use of any Bourns® products in such unauthorized applications might not be safe and thus is at
the user’s sole risk. Life-critical applications include devices identified by the U.S. Food and Drug Administration as Class III
devices and generally equivalent classifications outside of the United States.
Bourns expressly identifies those Bourns® standard products that are suitable for use in automotive applications on such
products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive
application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns
expressly identifies a sub-category of automotive application in the data sheet for its standard products (such as infotainment
or lighting), such identification means that Bourns has reviewed its standard product and has determined that if such Bourns®
standard product is considered for potential use in automotive applications, it should only be used in such sub-category of
automotive applications. Any reference to Bourns® standard product in the data sheet as compliant with the AEC-Q standard
or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application.
Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns expressly identifies Bourns® standard products that are suitable for use in aircraft
or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically
approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard
product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at
the user’s sole risk.
The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns
and the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns
and the user regarding the use and level of such testing, the above provisions applicable to Bourns® standard products shall
also apply to such Bourns® custom products.
Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns® products and Bourns technology and technical data may not under any circumstance be
exported or re-exported to countries subject to international sanctions or embargoes. Bourns® products may not, without
prior authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible
to receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential,
incidental or indirect damages or lost revenues or lost profits, and (ii) any and all implied warranties, including implied warranties
of fitness for particular purpose, non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese
bilingual versions are available at:
Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies
PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf
C1753 05/17/18R
