TBU-DT065-200-WH

PL IA NT Features ■ Superior circuit protection ■ Overcurrent and overvoltage protection ■ Blocks surges up to rated limits T8 007 55 4 Applications ■ Ethernet ports ■ Protection modules and dongles ■ Process control equipment ■ Test and measurement equipment ■ General electronics *R oH S CO M ■ High speed performance ■ Small SMT package ■ RoHS compliant* ■ Agency recognition: TBU-DT Series - TBU® High Speed Protectors General Information The TBU-DT Series of Bourns® TBU® (Transient Blocking Unit) products are very low capacitance dual unidirectional high speed surge protection components designed to protect against faults caused by short circuits, AC power cross, induction and lightning surges. The TBU-DT series is a unidirectional TBU® device; the TBU® protector will trip in less than 1 μs when the current reaches the maximum value in one direction only, that is when Pin 1 is positive in voltage with respect to Pin 2, and Pin 4 is positive with respect to Pin 3. No current limiting exists in the opposite polarity, and the TBU® device appears as resistive in nature. The reverse current should not exceed the maximum trip current level of the TBU® device. An external diode may be used to prevent reverse current in DC biased applications. The TBU® protector blocks surges and provides an effective barrier behind which sensitive electronics will not be exposed to large voltages or currents during surge events. After the surge, the TBU® device resets when the voltage across the TBU® device falls to the Vreset level. The TBU® device will automatically reset on lines which have no DC bias or have DC bias below Vreset (such as unpowered signal lines). The TBU® device is provided in a surface mount DFN package and meets industry standard requirements such as RoHS and Pb Free solder reflow profiles. Line Side 1 2 Load Side Line Side 4 3 Load Side TBU® Device Agency Approval Description UL File Number: E315805 Absolute Maximum Ratings (@ TA = 25 °C Unless Otherwise Noted) Symbol Vimp Vrms Top Tstg Parameter Peak impulse voltage withstand with duration less than 10 ms Continuous A.C. RMS voltage Operating temperature range Storage temperature range Part Number TBU-DT065-xxx-WH TBU-DT085-xxx-WH TBU-DT065-xxx-WH TBU-DT085-xxx-WH Value 650 850 300 425 -40 to +85 -65 to +150 Unit V V °C °C Electrical Characteristics (@ TA = 25 °C Unless Otherwise Noted) Symbol Itrigger Parameter Current required for the device to go from operating state to protected state Vimp = 650 V Vimp = 650 V Vimp = 650 V Vimp = 650 V Itrigger (min.) = Itrigger (min.) = Itrigger (min.) = Itrigger (min.) = 100 mA 200 mA 300 mA 500 mA Part Number TBU-DTxxx-100-WH TBU-DTxxx-200-WH TBU-DTxxx-300-WH TBU-DTxxx-500-WH TBU-DT065-100-WH TBU-DT065-200-WH TBU-DT065-300-WH TBU-DT065-500-WH Min. 100 200 300 500 Typ. 150 300 450 750 8.5 5.6 4.6 4.0 10.3 7.4 6.5 5.8 -0.5 0.25 12 0.50 16 116 96 Max. 200 400 600 1000 10.0 6.6 5.6 4.8 12.1 8.7 7.7 6.9 +0.5 1 1.00 20 Unit mA Rdevice Series resistance of the TBU® device Ω Rmatch tblock IQ Vreset Rth(j-l) Rth(j-l) Vimp = 850 V Itrigger (min.) = 100 mA TBU-DT085-100-WH Vimp = 850 V Itrigger (min.) = 200 mA TBU-DT085-200-WH Vimp = 850 V Itrigger (min.) = 300 mA TBU-DT085-300-WH Vimp = 850 V Itrigger (min.) = 500 mA TBU-DT085-500-WH Package resistance matching of the TBU® device #1 - TBU® device #2 Time for the device to go from normal operating state to protected state Current through the triggered TBU® device with 50 Vdc circuit voltage Voltage below which the triggered TBU® device will transition to normal operating state Junction to package pads - FR4 using recommended pad layout Junction to package pads - FR4 using heat sink on board (6 cm2) Ω µs mA V °C/W °C/W *RoHS Directive 2002/95/EC Jan 27, 2003 including Annex. Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TBU-DT Series - TBU® High Speed Protectors Reference Application The TBU device can be used to protect against excessive voltage surges in transformer coupled equipment, as shown in the figure below. The TBU® protector prevents any surges from causing damage. An overvoltage protection device, such as an MOV or GDT, may be used to provide additional overvoltage protection if the surge voltage is likely to be above the maximum rating of the TBU® device. ® Basic TBU Operation The TBU® device is a silicon-based, solid-state, resettable device which is placed in series with a signal path. The TBU® device operates in approximately 1 µs - once line current exceeds the TBU® device’s trigger current Itrigger. When operated, the TBU® device restricts line current to less than 1 mA typically. When operated, the TBU® device will block all system voltages and any other voltages including the surge up to rated limits. After the surge, the TBU® device resets when the voltage across the TBU® device falls to the Vreset level. The TBU® device will automatically reset on lines which have no DC bias or have DC bias below Vreset (such as unpowered signal lines). If the line has a normal DC bias above Vreset, the voltage across the TBU® device may not fall below Vreset after the surge. In such cases, special care needs to be taken to ensure that the TBU® device will reset, otherwise an automatic or manual power down will be required. Bourns application engineers can provide further assistance. 1 2 Line Side OVP Load OVP 4 3 TBU® Device Performance Graphs V-I Characteristic - TBU-DT085-300-WH (Pin 2-1 & Pin 3-4) ITRIP Typical Trigger Current vs. Temperature 1.8 Normalized Trip Current (A) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 0 25 50 75 100 125 150 CURRENT (100 mA/div.) VRESET VOLTAGE (5 v/div.) Junction Temperature (°C) Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. TBU-DT Series - TBU® High Speed Protectors Performance Graphs (Continued) Power Derating Curve 3.0 Typical Resistance vs. Temperature 2.2 2.5 Normalized Resistance (Ω) Total Max. Power (W) No additional PCB Cu (2 TBU® Protectors) 0.5 sq. in. additional PCB CU (2 TBU® Protectors) No additional PCB Cu (1 TBU® Protector) 0.5 sq. in. additional PCB CU (1 TBU® Protector) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 2.0 1.5 1.0 0.5 0.0 20 40 60 80 100 120 140 0 25 50 75 100 125 150 Junction Temperature (°C) Junction Temperature (°C) Reflow Profile Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Preheat - Temperature Min. (Tsmin) - Temperature Max. (Tsmax) - Time (tsmin to tsmax) Time maintained above: - Temperature (TL) - Time (tL) Peak/Classification Temperature (Tp) Time within 5 °C of Actual Peak Temp. (tp) Ramp-Down Rate Time 25 °C to Peak Temperature Pb-Free Assembly 3 °C/sec. max. 150 °C 200 °C 60-180 sec. 217 °C 60-150 sec. 260 °C 20-40 sec. 6 °C/sec. max. 8 min. max. Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. 3312 - 2 mm SMD Trimming Protectors TBU-DT Series - TBU® High SpeedPotentiometer Product Dimensions 0.75 (.030) 5.00 ± 0.10 (.197 ± .004) 0.85 ± 0.05 (.033 ± .002) 0.60 (.024) 3.05 (.120) 0.70 (.028) 5.00 ± 0.10 (.197 ± .004) SYMMETRY 0.35 (.014) PIN 1 & BACKSIDE CHAMFER 1.85 (.073) C 0.25 PIN 1 (.010) 0.00 - 0.05 (.000 - .002) DIMENSIONS: MM (INCHES) Recommended Pad Layout TBU® protectors have matte-tin termination finish. The suggested layout should use Non-Solder Mask Define (NSMD). The recommended stencil thickness is 0.10-0.12 mm (.004.005 in.) with a stencil opening size 0.025 mm (.0010 in.) less than the device pad size. As when heat sinking any power device, it is recommended that wherever possible, extra PCB copper area is allowed. For minimum parasitic capacitance, do not allow any signal, ground or power signals beneath any of the pads of the device. Thermal Resistance vs. Additional PCB Cu Area 120 Thermal Resistance to Ambient (°C/W) 100 Typical RTH (Power in 1 TBU® Device) Typical RTH (Equal Power in Both TBU® Devices) 80 60 40 Pad Designation 3 4 Pad # 1 2 2 1 3 4 Pin Out Line Side 1 Line Load 1 Line Load 2 Line Side 2 20 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Added Cu Area (Sq. In.) Dark grey areas show added PCB copper area for better thermal resistance. Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications 3312 - Series - TBU® High Speed Protectors TBU-DT 2 mm SMD Trimming Potentiometer How to Order Typical Part Marking TBU - DT 065 - 500 - WH TBU® Product Series DT = Dual Uni-Series Impulse Voltage Rating 065 = 650 V 085 = 850 V Trigger Current 100 = 100 mA 200 = 200 mA PIN 1 MANUFACTURER’S TRADEMARK PRODUCT CODE - 1ST DIGIT INDICATES PRODUCT FAMILY: T = TBU-DT SERIES - 2ND & 3RD DIGITS INDICATE IMPULSE VOLTAGE: 25 = 250 V 40 = 400 V 50 = 500 V - 4TH DIGIT INDICATES TRIGGER CURRENT: 1 = 100 mA 3 = 300 mA 2 = 200 mA 5 = 500 mA 300 = 300 mA 500 = 500 mA Hold to Trip Ratio Suffix W = Hold to Trip Ratio Package Suffix H = DFN Package MANUFACTURING DATE CODE - 1ST DIGIT INDICATES THE YEAR’S 6-MONTH PERIOD. - 2ND DIGIT INDICATES THE WEEK NUMBER IN THE 6-MONTH PERIOD. - 3RD & 4TH DIGITS INDICATE SPECIFIC LOT FOR THE WEEK. 6-MONTH PERIOD CODES: A = JAN-JUN 2009 C = JAN-JUN 2010 B = JUL-DEC 2009 D = JUL-DEC 2010 E = JAN-JUN 2011 F = JUL-DEC 2011 Packaging Specifications P0 E B t TOP COVER TAPE N D C F W D P2 A B0 K0 A0 P G (MEASURED AT HUB) CENTER LINES OF CAVITY D1 EMBOSSMENT DIMENSIONS: MM (INCHES) QUANTITY: 3000 PIECES PER REEL USER DIRECTION OF FEED A Min. 326 (12.835) A0 Min. 5.4 (.212) K0 Min. 1.1 (.043) Max. 1.3 (.051) Min. 7.9 (.311) Max. 5.6 (.220) Min. 5.4 (.212) P Max. 330 (13.002) Min. 1.5 (.059) B0 B Max. 2.5 (.098) D Max. 5.6 (.220) Max. 8.1 (.319) Min. 1.5 (.059) P0 Min. 3.9 (.159) Max. 4.1 (.161) Max. 1.6 (.063) Min. 12.8 (.504) C Max. 13.5 (.531) D1 Min. 1.5 (.059) P2 Min. 1.9 (.075) Max. 2.1 (.083) Max. Min. 20.2 (.795) D Max. E Min. 1.65 (.065) t Min. 0.25 (.010) Max. 0.35 (.014) Max. 1.85 (.073) G Ref. 16.5 (.650) F Min. 7.4 (.291) W Min. 15.7 (.618) N Ref. 102 (4.016) max. 7.6 (.299) Max. 16.3 (.642) 12/10 Asia-Pacific: Tel: +886-2 2562-4117 • Fax: +886-2 2562-4116 Europe: Tel: +41-41 768 5555 • Fax: +41-41 768 5510 The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700 www.bourns.com “TBU” is a registered trademark of Bourns, Inc. in the U.S., Taiwan and European Community. Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications