BS62UV256TC

BSI FEATURES Ultra Low Power/Voltage CMOS SRAM 32K X 8 bit DESCRIPTION BS62UV256 • Ultra low operation voltage : 1.8V ~ 3.6V • Ultra low power consumption : Vcc = 2.0V C-grade : 10mA (Max.) operating current I- grade : 15mA (Max.) operating current 0.005uA (Typ.) CMOS standby current Vcc = 3.0V C-grade : 20mA (Max.) operating current I-grade : 25mA (Max.) operating current 0.01uA (Typ.) CMOS standby current • High speed access time : -15 150ns (Max.) at Vcc = 2.0V • Automatic power down when chip is deselected • Three state outputs and TTL compatible • Fully static operation • Data retention supply voltage as low as 1.5V • Easy expansion with CE and OE options The BS62UV256 is a high performance, ultra low power CMOS Static Random Access Memory organized as 32,768 words by 8 bits and operates from a wide range of 1.8V to 3.6V supply voltage. Advanced CMOS technology and circuit techniques provide both high speed and low power features with a typical CMOS standby current of 0.005uA and maximum access time of 150ns in 2V operation. Easy memory expansion is provided by an active LOW chip enable (CE), and active LOW output enable (OE) and three-state output drivers. The BS62UV256 has an automatic power down feature, reducing the power consumption significantly when chip is deselected. The BS62UV256 is available in the JEDEC standard 28 pin 330mil Plastic SOP, 8mmx13.4mm TSOP (normal type), 300mil Plastic SOJ and 600mil Plastic DIP. PRODUCT FAMILY PRODUCT FAMILY BS62UV256SC BS62UV256TC BS62UV256PC BS62UV256JC BS62UV256DC BS62UV256SI BS62UV256TI BS62UV256PI BS62UV256JI BS62UV256DI OPERATING TEMPERATURE Vcc RANGE SPEED (ns) Vcc= 2.0V POWER DISSIPATION STANDBY Operating (ICCSB1, Max) Vcc= Vcc= 3.0V 2.0V (ICC, Max) Vcc= Vcc= 3.0V 2.0V PKG TYPE SOP-28 TSOP-28 PDIP-28 SOJ-28 DICE SOP-28 TSOP-28 PDIP-28 SOJ-28 DICE +0 C to +70 C O O 1.8V ~ 3.6V 150 0.2uA 0.1uA 20mA 10mA -40 C to +85 C O O 1.8V ~ 3.6V 150 0.4uA 0.3uA 25mA 15mA PIN CONFIGURATIONS BLOCK DIAGRAM 28 27 26 25 24 23 VCC WE A13 A8 A9 A11 OE A10 CE DQ7 DQ6 DQ5 DQ4 DQ3 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 8 Data Input Buffer 8 A5 A6 A7 A12 A14 A13 A8 A9 A11 512 Column I/O Write Driver Sense Amp 64 Column Decoder 12 CE WE OE Vdd Gnd A4 A3 A2 A1 A0 A10 Control Address Input Buffer Buffer Address Input • 1 2 3 4 5 6 10 11 12 13 14 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 GND 18 Row Decoder 512 Memory Array 512 x 512 7 BS62UV256SC 22 8 BS62UV256SI 21 BS62UV256PC 9 BS62UV256PI 20 19 18 17 16 15 OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BS62UV256TC BS62UV256TI 28 27 26 25 24 23 22 21 20 19 18 17 16 15 A10 CE DQ7 DQ6 DQ5 DQ4 DQ3 GND DQ2 DQ1 DQ0 A0 A1 A2 8 Data Output Buffer 8 Brilliance Semiconductor Inc. reserves the right to modify document contents without notice. R0201-BS62UV256 • 1 Revision 2.2 April 2001 BSI PIN DESCRIPTIONS BS62UV256 Function These 15 address inputs select one of the 32768 x 8-bit words in the RAM CE is active LOW. Chip enables must be active to read from or write to the device. If chip enable is not active, the device is deselected and is in a standby power mode. The DQ pins will be in the high impedance state when the device is deselected. Name A0-A14 Address Input CE Chip Enable Input WE Write Enable Input The write enable input is active LOW and controls read and write operations. With the chip selected, when WE is HIGH and OE is LOW, output data will be present on the DQ pins; when WE is LOW, the data present on the DQ pins will be written into the selected memory location. OE Output Enable Input The output enable input is active LOW. If the output enable is active while the chip is selected and the write enable is inactive, data will be present on the DQ pins and they will be enabled. The DQ pins will be in the high impedance state when OE is inactive. DQ0-DQ7 Data Input/Output Ports Vcc Gnd These 8 bi-directional ports are used to read data from or write data into the RAM. Power Supply Ground TRUTH TABLE MODE Not selected Output Disabled Read Write WE X H H L CE H L L L OE X H L X I/O OPERATION High Z High Z DOUT DIN Vcc CURRENT ICCSB, ICCSB1 ICC ICC ICC ABSOLUTE MAXIMUM RATINGS(1) SYMBOL V TERM T BIAS T STG PT I OUT PARAMETER Terminal Voltage with Respect to GND Temperature Under Bias Storage Temperature Power Dissipation DC Output Current OPERATING RANGE UNITS V O RATING -0.5 to Vcc+0.5 -40 to +125 -60 to +150 1.0 20 RANGE Commercial Industrial AMBIENT TEMPERATURE 0 O C to +70 O C -40 O C to +85 O C Vcc 1.8V ~ 3.6V 1.8V ~ 3.6V C C O W mA CAPACITANCE (1) (TA = 25oC, f = 1.0 MHz) SYMBOL 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CIN CDQ PARAMETER Input Capacitance Input/Output Capacitance CONDITIONS MAX. UNIT VIN=0V VI/O=0V 6 8 pF pF 1. This parameter is guaranteed and not tested. R0201-BS62UV256 2 Revision 2.2 April 2001 BSI DC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC ) PARAMETER NAME VIL VIH IIL IOL VOL VOH ICC ICCSB ICCSB1 BS62UV256 TEST CONDITIONS Vcc=2.0V Vcc=3.0V Vcc=2.0V Vcc=3.0V PARAMETER Guaranteed Input Low Voltage(2) Guaranteed Input High Voltage(2) Input Leakage Current Output Leakage Current Output Low Voltage Output High Voltage Operating Power Supply Current Standby Current-TTL Standby Current-CMOS MIN. TYP. (1) MAX. -0.5 1.4 2.0 --Vcc=2.0V Vcc=3.0V Vcc=2.0V Vcc=3.0V Vcc=2.0V UNITS V V uA uA V V mA mA uA ----------0.005 0.01 0.6 0.8 Vcc+0.2 1 1 0.4 -10 20 0.5 1.0 0.1 0.2 Vcc = Max, VIN = 0V to Vcc Vcc = Max, CE = VIH, or OE = VIH, VI/O = 0V to Vcc Vcc = Max, IOL = 1mA Vcc = Min, IOH = -0.5mA CE = VIL, IDQ = 0mA, F = Fmax(3) CE = VIH, IDQ = 0mA CE VIN Vcc-0.2V, Vcc - 0.2V or VIN -1.6 2.4 ------- Vcc=3.0V Vcc=2.0V Vcc=3.0V Vcc=2.0V 0.2V Vcc=3.0V 1. Typical characteristics are at TA = 25oC. 2. These are absolute values with respect to device ground and all overshoots due to system or tester notice are included. 3. Fmax = 1/tRC . DATA RETENTION CHARACTERISTICS ( TA = 0oC to + 70oC ) SYMBOL VDR ICCDR tCDR tR PARAMETER Vcc for Data Retention Data Retention Current Chip Deselect to Data Retention Time Operation Recovery Time CE VIN CE VIN TEST CONDITIONS Vcc - 0.2V Vcc - 0.2V or VIN Vcc -0.2V Vcc - 0.2V or VIN 0.2V 0.2V MIN. 1.5 -0 TRC (2) TYP. (1) -0.005 --- MAX. -0.1 --- UNITS V uA ns ns See Retention Waveform 1. Vcc = 1.5V, TA = + 25OC 2. tRC = Read Cycle Time LOW VCC DATA RETENTION WAVEFORM (1) ( CE Controlled ) Data Retention Mode Vcc VIH Vcc VDR ≥ 1.5V Vcc t CDR CE ≥ Vcc - 0.2V tR VIH CE R0201-BS62UV256 3 Revision 2.2 April 2001 BSI AC TEST CONDITIONS Input Pulse Levels Input Rise and Fall Times Input and Output Timing Reference Level Vcc/0V 5ns 0.5Vcc WAVEFORM INPUTS MUST BE STEADY BS62UV256 KEY TO SWITCHING WAVEFORMS OUTPUTS MUST BE STEADY WILL BE CHANGE FROM H TO L WILL BE CHANGE FROM L TO H CHANGE : STATE UNKNOWN CENTER LINE IS HIGH IMPEDANCE ”OFF ”STATE AC TEST LOADS AND WAVEFORMS 2V OUTPUT 100PF INCLUDING JIG AND SCOPE MAY CHANGE FROM H TO L 1333 Ω 1333 Ω 2V OUTPUT MAY CHANGE FROM L TO H DON T CARE: ANY CHANGE PERMITTED DOES NOT APPLY , 5PF 2000 Ω INCLUDING JIG AND SCOPE 2000 Ω FIGURE 1A THEVENIN EQUIVALENT 800 Ω FIGURE 1B OUTPUT 1.2V ALL INPUT PULSES Vcc GND 10% 90% 90% 10% → ← → ← 5ns FIGURE 2 AC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC, Vcc = 2.0V ) READ CYCLE JEDEC PARAMETER NAME PARAMETER NAME DESCRIPTION Read Cycle Time Address Access Time Chip Select Access Time Output Enable to Output Valid Chip Select to Output Low Z Output Enable to Output in Low Z Chip Deselect to Output in High Z Output Disable to Output in High Z Output Disable to Output Address Change BS62UV256 -15 MIN. TYP. MAX. UNIT ns ns ns ns ns ns ns ns ns t AVAX t AVQV t ELQV t GLQV t ELQX t GLQX t EHQZ t GHQZ t AXOX t RC t AA t ACS t OE t CLZ t OLZ t CHZ t OHZ t OH 150 ---10 10 0 0 10 ---------- -150 150 100 --35 30 -- R0201-BS62UV256 4 Revision 2.2 April 2001 BSI SWITCHING WAVEFORMS (READ CYCLE) READ CYCLE1 (1,2,4) BS62UV256 t RC ADDRESS t D OUT t OH AA t OH READ CYCLE2 (1,3,4) CE t t D OUT (5) CLZ ACS t CHZ (5) READ CYCLE3 (1,4) t RC ADDRESS t OE AA t OE CE t OH t OLZ t ACS t CLZ (5) t OHZ (5) (1,5) t CHZ D OUT NOTES: 1. WE is high in read Cycle. 2. Device is continuously selected when CE = VIL. 3. Address valid prior to or coincident with CE transition low. 4. OE = VIL . 5. Transition is measured ± 500mV from steady state with CL = 5pF as shown in Figure 1B. The parameter is guaranteed but not 100% tested. R0201-BS62UV256 5 Revision 2.2 April 2001 BSI AC ELECTRICAL CHARACTERISTICS ( TA = 0oC to + 70oC, Vcc = 2.0V ) WRITE CYCLE JEDEC PARAMETER NAME PARAMETER NAME DESCRIPTION Write Cycle Time Chip Select to End of Write Address Set up Time Address Valid to End of Write Write Pulse Width Write Recovery Time Write to Output in High Z Data to Write Time Overlap Data Hold from Write Time Output Disable to Output in High Z End ot Write to Output Active (CE , WE) BS62UV256 BS62UV256-15 MIN. TYP. MAX. UNIT ns ns ns ns ns ns ns ns ns ns ns t AVAX t E1LWH t AVWL t AVWH t WLWH t WHAX t WLOZ t DVWH t WHDX t GHOZ t WHQX t WC t CW t AS t AW t WP t WR t WHZ t DW t DH t OHZ t OW 150 150 0 150 80 0 -40 0 0 5 ------------ ------30 --30 -- SWITCHING WAVEFORMS (WRITE CYCLE) WRITE CYCLE1 (1) t WC ADDRESS t OE (3) WR t CW CE (5) (11) t AW WE t AS (4,10) t WP (2) t OHZ D OUT t t DW DH D IN R0201-BS62UV256 6 Revision 2.2 April 2001 BSI WRITE CYCLE2 (1,6) BS62UV256 t WC ADDRESS t CW (5) (11) CE t WE AW t WP (2) t AS (4,10) t DH t WHZ D OUT (7) (8) t DW t DH (8) D IN NOTES: 1. WE must be high during address transitions. 2. The internal write time of the memory is defined by the overlap of CE and WE low. All signals must be active to initiate a write and any one signal can terminate a write by going inactive. The data input setup and hold timing should be referenced to the second transition edge of the signal that terminates the write. 3. TWR is measured from the earlier of CE or WE going high at the end of write cycle. 4. During this period, DQ pins are in the output state so that the input signals of opposite phase to the outputs must not be applied. 5. If the CE low transition occurs simultaneously with the WE low transitions or after the WE transition, output remain in a high impedance state. 6. OE is continuously low (OE = VIL ). 7. DOUT is the same phase of write data of this write cycle. 8. DOUT is the read data of next address. 9. If CE is low during this period, DQ pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 10. Transition is measured ± 500mV from steady state with CL = 5pF as shown in Figure 1B. The parameter is guaranteed but not 100% tested. 11. TCW is measured from the later of CE going low to the end of write. R0201-BS62UV256 7 Revision 2.2 April 2001 BSI ORDERING INFORMATION BS62UV256 BS62UV256 XX YY SPEED 15: 150ns GRADE C: +0oC ~ +70oC I: -40oC ~ +85oC PACKAGE S: SOP P: PDIP J : SOJ T: TSOP (8mm x 13.4mm) D : DICE PACKAGE DIMENSIONS 0.020 0.005X45 θ WITH PLATING b c c1 BASE METAL b1 SOP - 28 R0201-BS62UV256 8 Revision 2.2 April 2001 BSI PACKAGE DIMENSIONS (continued) 12 (2x) 12 (2x) BS62UV256 UNIT SYMBOL INCH 0.0433 0.004 0.0045 0.0026 0.039 0.002 0.009 0.002 0.008 0.001 0.004 ~ 0.008 0.004 ~ 0.006 0.465 0.004 0.315 0.004 0.022 0.004 0.528 0.008 0.0197 +0.008 - 0.004 0.0315 0.004 0.004 Max. 0~ 8 MM 1.10 0.10 0.115 0.065 1.00 0.05 0.22 0.05 0.20 0.03 0.10 ~ 0.21 0.10 ~ 0.16 11.80 0.10 8.00 0.10 0.55 0.10 13.40 0.20 0.50 +0.20 - 0.10 0.80 0.10 0.1 Max. 0~ 8 A A1 A2 b b1 c c1 D E e HD L L1 y 0 HD c L 1 28 E b e Seating Plane y 14 15 12 (2X) "A" D GAUGE PLANE A2 A A 0.254 0 A1 14 15 SEATING PLANE A 12 (2X) L "A" DATAIL VIEW L1 WITH PLATING 1 28 b c c1 BASE METAL b1 SECTION A-A TSOP - 28 PDIP - 28 R0201-BS62UV256 9 Revision 2.2 April 2001 BSI BS62UV256 SOJ - 28 R0201-BS62UV256 10 Revision 2.2 April 2001 BSI REVISION HISTORY Revision 2.2 BS62UV256 Description 2001 Data Sheet release Date Apr. 15, 2001 Note R0201-BS62UV256 11 Revision 2.2 April 2001