66AK2H12BAAW2

Product Folder Order Now Technical Documents Tools & Software Support & Community Reference Design 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 66AK2Hxx Multicore DSP+ARM® KeyStone™ II System-on-Chip (SoC) 1 Device Overview 1.1 Features 1 • Eight TMS320C66x DSP Core Subsystems (C66x CorePacs), Each With – 1.0 GHz or 1.2 GHz C66x Fixed- and FloatingPoint DSP Core – 38.4 GMacs/Core for Fixed Point @ 1.2 GHz – 19.2 GFlops/Core for Floating Point @ 1.2 GHz – Memory – 32-KB L1P Per CorePac – 32-KB L1D Per CorePac – 1024-KB Local L2 Per CorePac • ARM CorePac – Four ARM® Cortex®-A15 MPCore™ Processors at up to 1.4 GHz – 4MB of L2 Cache Memory Shared by Four ARM Cores – Full Implementation of ARMv7-A Architecture Instruction Set – 32-KB L1 Instruction and Data Caches per Core – AMBA 4.0 AXI Coherency Extension (ACE) Master Port, Connected to MSMC for LowLatency Access to Shared MSMC SRAM • Multicore Shared Memory Controller (MSMC) – 6MB of MSM SRAM Memory Shared by Eight DSP CorePacs and One ARM CorePac – Memory Protection Unit (MPU) for Both MSM SRAM and DDR3_EMIF • Multicore Navigator – 16k Multipurpose Hardware Queues With Queue Manager – Packet-Based DMA for Zero-Overhead Transfers • Network Coprocessor – Packet Accelerator Enables Support for – Transport Plane IPsec, GTP-U, SCTP, PDCP – L2 User Plane PDCP (RoHC, Air Ciphering) – 1-Gbps Wire Speed Throughput at 1.5 MPackets Per Second – Security Accelerator Engine Enables Support for – IPSec, SRTP, 3GPP, and WiMAX Air Interface, and SSL/TLS Security – ECB, CBC, CTR, F8, A5/3, CCM, GCM, HMAC, CMAC, GMAC, AES, DES, 3DES, Kasumi, SNOW 3G, SHA-1, SHA-2 (256-Bit Hash), MD5 – Up to 2.4 Gbps IPSec and 2.4 Gbps Air Ciphering – Ethernet Subsystem – Five-Port Switch (Four SGMII Ports) • Peripherals – Four Lanes of SRIO 2.1 – Supports up to 5 GBaud – Supports Direct I/O, Message Passing – Two Lanes PCIe Gen2 – Supports up to 5 GBaud – Two HyperLinks – Supports Connections to Other KeyStone™ Architecture Devices Providing Resource Scalability – Supports up to 50 GBaud – 10-Gigabit Ethernet (10-GbE) Switch Subsystem (66AK2H14 Only) – Two XFI Ports – IEEE 1588 Support – Five Enhanced Direct Memory Access (EDMA) Modules – Two 72-Bit DDR3/DDR3L Interfaces With Speeds up to 1600 MHz – EMIF16 Interface – USB 3.0 – Two UART Interfaces – Three I2C Interfaces – 32 GPIO Pins – Three SPI Interfaces – Semaphore Module – 64-Bit Timers – Twenty 64-Bit Timers for 66AK2H14 and 66AK2H12 – Fourteen 64-Bit Timers for 66AK2H06 – Five On-Chip PLLs • Commercial Case Temperature: – 0ºC to 85ºC • Extended Case Temperature: – –40ºC to 100ºC 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 1.2 • • • • • www.ti.com Applications Mission Critical Computing Communications Audio Video Infrastructure 1.3 • • • • Imaging Analytics Networking Media Processing Description The 66AK2Hxx platform combines the quad ARM Cortex-A15 processor with up to eight TMS320C66x high-performance DSPs using the KeyStone II architecture. The 66AK2H14/12/06 device provides up to 5.6 GHz of ARM and 9.6 GHz of DSP processing coupled with security, packet processing, and Ethernet switching at lower power than multichip solutions. The 66AK2H14/12/06 device is optimal for embedded infrastructure applications like cloud computing, media processing, high-performance computing, transcoding, security, gaming, analytics, and virtual desktop. The C66x core combines fixed-point and floating-point computational capability in the processor without sacrificing speed, size, or power consumption. The raw computational performance is 38.4 GMACS/core and 19.2 Gflops/core (@ 1.2 GHz operating frequency). The C66x is also 100% backward compatible with software for C64x+ devices. The C66x core incorporates 90 new instructions targeted for floating point (FPi) and vector math oriented (VPi) processing. The 66AK2H14/12/06 device has a complete set of development tools that includes: a C compiler, an assembly optimizer to simplify programming and scheduling, and a Windows® debugger interface for visibility into source code execution. 1.3.1 Enhancements in KeyStone II The KeyStone II architecture provides many major enhancements over the previous KeyStone I generation of devices. The KeyStone II architecture integrates a Cortex-A15 processor quad-core cluster. The external memory bandwidth has been doubled with the integration of dual DDR3 1600 EMIFs. MSMC internal memory bandwidth is quadrupled with MSMC architecture improvements such as cache coherency. MSMC also enbles memories to operate at the speed of the processor cores, which reduces latency and contention while providing high-bandwidth interconnections between processor cores and shared internal and external memory. Multicore Navigator supports twice the number of queues, descriptors, and packet DMA, four times the number of micro RISC engines, and a significant increase in the number of push/pops per second compared to the previous generation. The new peripherals that have been added include the USB 3.0 controller, and asynchronous EMIF controller for NAND/NOR memory access. The 3-port Gigabit Ethernet switch in KeyStone I has been replaced with a 5-port Gigabit Ethernet switch in KeyStone II. Time synchronization support has been enhanced to reduce software workload and support additional standards like IEEE 1588 Annex D/E and SyncE. The number of GPIOs and serial interface peripherals, like I2C and SPI, have been increased to enable more board-level control functionality. Device Information (1) PACKAGE BODY SIZE 66AK2H14 PART NUMBER AAW 40.0 mm × 40.0 mm 66AK2H12 AAW 40.0 mm × 40.0 mm 66AK2H06 AAW 40.0 mm × 40.0 mm (1) 2 For more information, see Section 13, Mechanical, Packaging, and Orderable Information. Device Overview Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 1.4 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Functional Block Diagram Figure 1-1, Figure 1-2, and Figure 1-3 show the functional block diagrams of the devices. 66AK2H14 C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ CorePac CorePac CorePac CorePac CorePac CorePac CorePac CorePac Memory Subsystem 72-Bit DDR3 EMIF 6MB MSM SRAM 72-Bit DDR3 EMIF MSMC 32KBL1 L1 32KB 32KBL1 L1 32KB 32KB L1 32KB 32KBL1 L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache 1024KB L2Cache Cache 1024KB L2 1024KBL2 L2Cache Cache 1024KB 1024KB L2Cache Cache 1024KB L2 1024KB L2 Cache 1024KB L2 Cache Debug & Trace Boot ROM 8´ 32KB L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache ARM A15 Semaphore Power Management ARM A15 4MB L2 Cache ARM A15 PLL 5´ ARM A15 32KB L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache EDMA 8 C66x DSP Cores @ up to 1.2 GHz 4 ARM Cores @ up to 1.4 GHz 5´ TeraNet 2´ HyperLink Multicore Navigator Packet DMA Security Accelerator Packet Accelerator 1GBE 1GBE 1GBE 5-Port Ethernet Switch 1GBE 10GBE 3-Port Ethernet Switch 10GBE 10GBE SRIO ´4 PCIe ´2 3´ SPI 2´ UART USB 3.0 3´ I2C GPIO ´32 EMIF16 Queue Manager Network Coprocessor Copyright © 2016, Texas Instruments Incorporated Figure 1-1. Functional Block Diagram for 66AK2H14 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Overview 3 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 66AK2H12 C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ C66x™ CorePac CorePac CorePac CorePac CorePac CorePac CorePac CorePac Memory Subsystem 72-Bit DDR3 EMIF 6MB MSM SRAM 72-Bit DDR3 EMIF MSMC 32KBL1 L1 32KB 32KBL1 L1 32KB 32KB L1 32KB 32KBL1 L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache 1024KB L2Cache Cache 1024KB L2 1024KB L2 Cache 1024KBL2 L2Cache Cache 1024KB 1024KB L2Cache Cache 1024KB L2 1024KB L2 Cache Debug & Trace Boot ROM 8´ 32KB L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache ARM A15 Semaphore Power Management ARM A15 4MB L2 Cache ARM A15 PLL 5´ ARM A15 32KB L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache EDMA 8 C66x DSP Cores @ up to 1.2 GHz 4 ARM Cores @ up to 1.4 GHz 5´ TeraNet 2´ HyperLink Multicore Navigator Packet DMA Security Accelerator Packet Accelerator 1GBE 1GBE 1GBE 5-Port Ethernet Switch 1GBE SRIO ´4 PCIe ´2 3´ SPI 2´ UART USB 3.0 3´ I2C GPIO ´32 EMIF16 Queue Manager Network Coprocessor Copyright © 2016, Texas Instruments Incorporated Figure 1-2. Functional Block Diagram for 66AK2H12 4 Device Overview Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 66AK2H06 Memory Subsystem C66x™ C66x™ C66x™ C66x™ CorePac CorePac CorePac CorePac 72-Bit DDR3 EMIF 6MB MSM SRAM 72-Bit DDR3 EMIF MSMC 32KBL1 L1 32KB 32KBL1 L1 32KB 32KB L1 32KB 32KBL1 L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache P-Cache D-Cache D-Cache P-Cache 1024KBL2 L2Cache Cache 1024KB 1024KB L2Cache Cache 1024KB L2 1024KB L2 Cache Debug & Trace Boot ROM 4´ 32KB L1 32KB L1 32KB L1 32KB L1 P-Cache D-Cache P-Cache D-Cache Semaphore ARM A15 Power Management ARM A15 4MB L2 Cache PLL 5´ EDMA 4 C66x DSP Cores @ up to 1.2 GHz 2 ARM Cores @ up to 1.4 GHz 5´ TeraNet 2´ HyperLink Multicore Navigator Packet DMA Security Accelerator Packet Accelerator 1GBE 1GBE 1GBE 1GBE 5-Port Ethernet Switch SRIO ´4 PCIe ´2 3´ SPI 2´ UART USB 3.0 3´ I2C GPIO ´32 EMIF16 Queue Manager Network Coprocessor Copyright © 2016, Texas Instruments Incorporated Figure 1-3. Functional Block Diagram for 66AK2H06 Table of Contents 1 2 3 Device Overview ......................................... 1 Pullup/Pulldown Resistors .......................... 50 Features .............................................. 1 1.2 Applications ........................................... 2 5.1 Absolute Maximum Ratings ......................... 52 1.3 Description ............................................ 2 5.2 ESD Ratings 1.4 Functional Block Diagram ............................ 3 5.3 Recommended Operating Conditions ............... 53 Revision History ......................................... 7 Device Comparison ..................................... 8 5.4 Power Consumption Summary...................... 53 5.5 5.6 Electrical Characteristics ............................ 54 Thermal Resistance Characteristics for PBGA Package [AAW] ..................................... 54 5.7 Power Supply to Peripheral I/O Mapping ........... 55 3.1 4 4.4 1.1 5 Related Products ..................................... 9 Specifications ........................................... 52 Terminal Configuration and Functions ............ 10 4.1 Package Terminals .................................. 10 4.2 Pin Map 4.3 Terminal Functions .................................. 15 ............................................. 10 6 ........................................ 52 C66x CorePac ........................................... 56 6.1 C66x DSP CorePac ................................. 57 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Table of Contents 5 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 6.2 Memory Architecture ................................ 57 11.7 PASS PLL .......................................... 275 6.3 Memory Protection .................................. 60 11.8 External Interrupts 61 11.9 DDR3A and DDR3B Memory Controllers .......... 278 ............................ 6.5 Power-Down Control ................................ 6.6 C66x CorePac Revision ............................. 6.7 C66x CorePac Register Descriptions ............... ARM CorePac ........................................... 7.1 Features ............................................. 7.2 System Integration .................................. 7.3 ARM Cortex-A15 Processor ......................... 7.4 CFG Connection .................................... 7.5 Main TeraNet Connection ........................... 7.6 Clocking and Reset ................................. Memory, Interrupts, and EDMA for 66AK2Hxx ... 8.1 Memory Map Summary for 66AK2Hxx .............. 8.2 Memory Protection Unit (MPU) for 66AK2Hxx ...... 8.3 Interrupts for 66AK2Hxx ............................. 6.4 7 8 Bandwidth Management 8.4 9 www.ti.com 61 11.10 I2C Peripheral ..................................... 280 11.11 SPI Peripheral 284 62 11.12 11.13 65 11.14 65 11.15 65 69 11.16 11.17 Network Coprocessor Gigabit Ethernet (GbE) Switch Subsystem ................................. 11.18 SGMII and XFI Management Data Input/Output (MDIO) ............................................. 11.19 Ten-Gigabit Ethernet (10GbE) Switch Subsystem ......................................... 79 11.20 Timers............................................. 294 93 Enhanced Direct Memory Access (EDMA3) Controller for 66AK2Hxx ........................... 157 11.21 Serial RapidIO (SRIO) Port ....................... 295 ................ Switch Fabric Connections Matrix - Data Space .. 67 67 68 69 168 168 TeraNet Switch Fabric Connections Matrix Configuration Space ............................... 175 Bus Priorities ....................................... 181 9.4 .................................... HyperLink Peripheral ............................. UART Peripheral ................................. PCIe Peripheral ................................... Packet Accelerator ............................... Security Accelerator .............................. 63 Internal Buses and Switch Fabrics 9.2 9.3 277 62 System Interconnect ................................. 168 9.1 ................................. 11.22 General-Purpose Input/Output (GPIO) ........... 287 289 290 290 291 291 292 294 296 11.23 Semaphore2 ...................................... 297 11.24 Universal Serial Bus 3.0 (USB 3.0) ............... 297 11.25 EMIF16 Peripheral ................................ 297 11.26 Emulation Features and Capability ............... 300 11.27 Debug Port (EMUx) ............................... 303 12 Device and Documentation Support .............. 312 10 Device Boot and Configuration .................... 182 12.1 Device Nomenclature .............................. 312 Device Boot ........................................ 182 12.2 Tools and Software ................................ 314 Device Configuration ............................... 206 12.3 Documentation Support ............................ 315 11 66AK2Hxx Peripheral Information................. 237 12.4 Related Links 12.5 Community Resources............................. 321 12.6 Trademarks ........................................ 321 10.1 10.2 11.1 6 Recommended Clock and Control Signal Transition Behavior............................................ 237 .................................... ...................................... ................... 321 11.2 Power Supplies 237 12.7 Electrostatic Discharge Caution 11.3 Power Sleep Controller (PSC) ..................... 245 12.8 Glossary............................................ 321 11.4 11.5 Reset Controller .................................... 251 Main PLL, ARM PLL, DDR3A PLL, DDR3B PLL, PASS PLL and the PLL Controllers................ 257 11.6 DDR3A PLL and DDR3B PLL Table of Contents ..................... 321 13 Mechanical, Packaging, and Orderable Information ............................................. 322 13.1 Packaging Information ............................. 322 272 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 2 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision F (June 2017) to Revision G • • • • • • • • Page Added DDR3L Interface to Features. ............................................................................................. 1 Updated DVDD15 power supply in Terminal Functions — Power and Ground table from 1.5 V to 1.35/1.5 V......... 32 Updated DVDD15 entry in Recommended Operating Conditions table. .................................................... 53 Updated DVDD15 power supply in Power Supply to Peripheral I/O Mapping table, from 1.5 V to 1.35/1.5 V. ........ 55 Added DSP Boot Address Register (DSP_BOOT_ADDRn). ................................................................ 213 Updated DVDD15 value in Power Supply Rails table from 1.5 V to 1.35/1.5V. ........................................... 237 Updated DDR3 value in DDR3 Memory Controller Device-Specific Information section from 1.5-V to 1.35-V / 1.5-V. ............................................................................................................................... 278 Updated Timers Device-Specific Information section. ....................................................................... 294 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Revision History 7 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 3 Device Comparison Table 3-1 provides a comparison of the 66AK2Hxx devices. The table lists the significant features of the devices, including the capacity of on-chip RAM, the peripherals, the CPU frequency, and the package type with pin count. Table 3-1. Device Features Comparison HARDWARE FEATURES Cores Peripherals 66AK2H14 66AK2H12 66AK2H06 C66x DSP 8 8 4 ARM Cortex-A15 MPCore 4 4 2 10-GbE 2 – – DDR3 memory controller (72-bit bus width) 2 2 2 16-bit ASYNC EMIF 1 1 1 EDMA3 (64 independent channels) 5 5 5 High-speed 1×/2×/4× Serial RapidIO port (4 lanes) 1 1 1 HyperLink (4 lanes) 2 2 2 I2C 3 3 3 SPI 3 3 3 PCIe (2 lanes) 1 1 1 USB 3.0 1 1 1 UART 2 2 2 10/100/1000 Ethernet 4 4 4 Management Data Input/Output (MDIO) 1 1 1 Twenty 64-bit or Forty 32bit Twenty 64-bit or Forty 32-bit Fourteen 64-bit or Twenty Eight 32-bit General-Purpose Input/Output port (GPIO) 32 32 32 Packet Accelerator 1 1 1 Security Accelerator (1) 1 1 1 L1 program memory controller (C66x) 32KB per CorePac 32KB per CorePac 32KB per CorePac L1 data memory controller (C66x) 32KB per CorePac 32KB per CorePac 32KB per CorePac 8192KB 8192KB 4096KB 64-bit timers (configurable) Accelerators Shared L2 cache (C66x) L3 ROM (C66x) On-Chip Memory Organization 128KB 128KB 128KB L1 program memory controller (ARM Cortex-A15) 32KB per CorePac 32KB per CorePac 32KB per CorePac L1 data memory controller (ARM CortexA15) 32KB per CorePac 32KB per CorePac 32KB per CorePac Shared L2 cache (ARM Cortex-A15) 4096KB 4096KB 4096KB L3 ROM (ARM Cortex-A15) 256KB 256KB 256KB MSMC C66x CorePac Revision ID JTAG BSDL_ID Frequency (1) 8 6MB CorePac Revision ID Register (address location: 0181 2000h) 0x0009_0000 0x0009_0002 0x0009_0003 0x0009_0003 0x0009_0003 JTAGID Register (address location: 0x02620018) 0x0b98102f 0x1b98102f 0x2b98102f 0x3b98102f 0xbb98102f 6MB (PG (PG (PG (PG (PG (PG (PG (PG (PG (PG 1.0) 1.1) 2.0) 3.0) 3.1) 1.0) 1.1) 2.0) 3.0) 3.1) 0x0009_0000 0x0009_0002 0x0009_0003 0x0009_0003 0x0009_0003 0x0b98102f 0x1b98102f 0x2b98102f 0x3b98102f 0xbb98102f 6MB (PG (PG (PG (PG (PG (PG (PG (PG (PG (PG 1.0) 1.1) 2.0) 3.0) 3.1) 1.0) 1.1) 2.0) 3.0) 3.1) 0x0009_0000 0x0009_0002 0x0009_0003 0x0009_0003 0x0009_0003 0x0b98102f 0x1b98102f 0x2b98102f 0x3b98102f 0xbb98102f (PG (PG (PG (PG (PG (PG (PG (PG (PG (PG 1.0) 1.1) 2.0) 3.0) 3.1) 1.0) 1.1) 2.0) 3.0) 3.1) C66x Up to 1.2 GHz Up to 1.2 GHz Up to 1.2 GHz ARM Cortex-A15 Up to 1.4 GHz Up to 1.4 GHz Up to 1.4 GHz The Security Accelerator function is subject to export control and will be enabled only for approved device shipments. Device Comparison Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 3-1. Device Features Comparison (continued) HARDWARE FEATURES Core (V) Voltage I/O (V) BGA Package Process Technology 3.1 40 mm × 40 mm µm 66AK2H14 66AK2H12 66AK2H06 SmartReflex™ variable supply SmartReflex™ variable supply SmartReflex™ variable supply 0.85 V, 1.0 V, 1.35 V, 1.5 V, 1.8 V and 3.3 V 0.85 V, 1.0 V, 1.35 V, 1.5 V, 1.8 V and 3.3 V 0.85 V, 1.0 V, 1.35 V, 1.5 V, 1.8 V and 3.3 V 1517-pin flip-chip plastic BGA (AAW) 1517-pin flip-chip plastic BGA (AAW) 1517-pin flip-chip plastic BGA (AAW) 0.028 µm 0.028 µm 0.028 µm Related Products For information about other devices in this family of products or related products, see the following links. Digital Signal Processors From sensors to servers, TI has the right DSPs for every application. 66AK2x Multicore DSP + ARM Processors Describes the features, applications, and products available on these processors. Companion Products for 66AK2Hxx Review products that are frequently purchased or used in conjunction with this product. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Comparison 9 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 4 Terminal Configuration and Functions 4.1 Package Terminals Figure 4-1 shows the AAW ball grid array package (bottom view). The 14 pins that serve the 10-GbE function (XFI) in the 66AK2H14 are reserved in the 66AK2H12/06 devices. Figure 4-1. AAW 1517-Pin BGA Package (Bottom View) 4.2 Pin Map The following figures show the 66AK2Hxx pin assignments in four quadrants (A, B, C, and D). The 14 pins serving the 10-GbE function (XFI) in the 66AK2H14 device are reserved in the 66AK2H12/06 devices. A B C D Figure 4-2. Pin Map Panels (Bottom View) 10 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 1 2 3 4 5 6 7 8 9 10 AW (NOPIN) VSS VSS HYP1CLKP HYP1CLKN VSS HYP0RXN3 HYP0RXP3 VSS HYP0RXN0 AV VSS VSS HYP1RXN3 HYP1RXP3 VSS HYP1RXN1 HYP1RXP1 VSS HYP0RXN2 HYP0RXP2 AU VSS VSS VSS HYP1RXN2 HYP1RXP2 VSS HYP1RXN0 HYP1RXP0 VSS HYP0RXN1 AT RSV190 VSS HYP1TXN3 HYP1TXP3 VSS HYP1TXN0 HYP1TXP0 VSS HYP0CLKP HYP0CLKN AR RSV189 RSV186 VSS HYP1TXN2 HYP1TXP2 VSS HYP0TXN3 HYP0TXP3 VSS HYP0TXN1 AP TSRXCLKOUT0N RSV187 TSRXCLKOUT1N VSS HYP1TXN1 HYP1TXP1 VSS HYP0TXN2 HYP0TXP2 VSS AN TSRXCLKOUT0P VSS TSRXCLKOUT1P RSV002 VSS VSS VSS VSS VSS RSV019 AM TSREFCLKP ALTCORECLKP VSS RSV003 CVDD HYP1REFRES RSV020 VSS HYP0REFRES VSS AL TSREFCLKN ALTCORECLKN SYSCLKP CORECLKSEL VSS CVDD VSS CVDD VSS VDDAHV AK SYSCLKOUT VSS SYSCLKN POR RSV012 VSS CVDD VSS CVDD VSS AJ HYP0TXPMDAT HYP0RXPMCLK HYP0TXFLCLK HYP0RXFLDAT HYP0RXFLCLK VSS VSS CVDD VSS CVDD AH HYP1TXPMCLK HYP1TXFLDAT HYP1TXFLCLK HYP1RXFLCLK HYP0TXPMCLK VSS VSS VSS CVDD VSS AG TDI HYP1RXFLDAT HYP0RXPMDAT VSS HYP0TXFLDAT DVDD18 VSS CVDD VSS CVDD AF TDO HYP1TXPMDAT HYP1RXPMCLK AE TCK TMS VSS LRESET HYP1RXPMDAT BOOTCOMPLETE HOUT VSS DVDD18 VSS CVDD VSS DVDD18 VSS CVDD VSS CVDD AD TRST RESET RESETFULL LRESETNMIEN NMI VSS DVDD18 VSS CVDD VSS AC TSPUSHEVT1 TSPUSHEVT0 TSSYNCEVT RSV188 RESETSTAT DVDD18 VSS CVDD VSS CVDD AB TSCOMPOUT EMU01 EMU14 EMU10 DVDD18 VSS DVDD18 VSS CVDD VSS AA USBRESREF EMU00 EMU11 EMU18 VSS DVDD18 VSS CVDD VSS CVDD Y USBRX0M VSS EMU02 EMU03 DVDD18 VSS DVDD18 VSS CVDD VSS W USBRX0P USBCLKP EMU04 EMU05 VSS DVDD18 VSS CVDD VSS CVDD V USBTX0M USBCLKM VSS EMU06 DVDD18 VSS DVDD18 VSS CVDD VSS U USBTX0P USBDP EMU08 EMU07 EMU12 DVDD18 VSS CVDD VSS CVDD T USBVBUS USBDM EMU09 EMU13 EMU16 VSS DVDD18 VSS CVDD VSS R USBID0 VSS EMU15 EMU17 VSS DVDD18 VSS CVDD VSS CVDD P RSV001 RSV000 SDA0 SCL2 VSS VSS CVDD VSS CVDD VSS N SCL0 SDA1 SDA2 SCL1 VSS CVDD VSS CVDD VSS CVDD M TIMI1 TIMI0 TIMO0 TIMO1 UART1RTS VSS CVDD VSS CVDD VSS L UART0CTS UART1RXD USBDRVVBUS UART0RTS VSS CVDD VSS DVDD15 VSS DVDD15 K UART1CTS UART0TXD UART1TXD UART0RXD VSS VSS DVDD15 VSS DVDD15 VSS J VSS VSS VSS VSS VSS DVDD15 VSS DVDD15 VSS DVDD15 H DDR3AD04 DDR3AD01 DDR3AD13 VSS DDR3AD17 VSS DVDD15 VSS DVDD15 DDR3ARQ1 G DDR3AD00 DDR3AD03 DDR3AD10 DDR3AD16 DDR3AD20 DDR3AD29 DDR3AD30 DDR3AA02 DDR3AA01 DDR3AA03 F DDR3AD02 DDR3AD06 DDR3ADQM1 DDR3AD09 DDR3AD19 DDR3AD26 DDR3AD25 DDR3AA05 DDR3AA04 DDR3AA10 E DDR3ADQS0P DDR3AD05 VSS DDR3AD08 VSS DDR3ADQM3 VSS DDR3AA00 VSS DDR3AA12 D DDR3ADQS0N DDR3AD07 DDR3AD14 DDR3AD15 DDR3AD18 DDR3AD21 DDR3AD31 DDR3AA09 DDR3AA07 DDR3AA15 C VSS DDR3ADQM0 DDR3ADQS1N VSS DDR3AD22 VSS DDR3AD24 VSS DDR3AA06 VSS B VSS VSS DDR3ADQS1P DDR3AD12 DDR3ADQS2N DDR3AD23 DDR3ADQS3P DDR3AD28 DDR3AA08 DDR3AA14 A (NOPIN) VSS VSS DDR3AD11 DDR3ADQS2P DDR3ADQM2 DDR3ADQS3N DDR3AD27 DDR3AA11 DDR3AA13 1 2 3 4 5 6 7 8 9 10 Figure 4-3. 66AK2Hxx Pin Map Left Side Panel (A) — Bottom View Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 11 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11 12 13 14 15 16 17 18 19 20 HYP0RXP0 VSS RSV167 RSV168 VSS RSV161 RSV162 VSS XFIRXP1 XFIRXN1 AV VSS RSV171 RSV172 VSS RSV165 RSV166 VSS XFIRXP0 XFIRXN0 VSS AU HYP0RXP1 VSS RSV169 RSV170 VSS RSV163 RSV164 VSS XFICLKP XFICLKN AW AT VSS RSV183 RSV184 VSS RSV177 RSV178 VSS XFITXP0 XFITXN0 VSS AR HYP0TXP1 VSS RSV181 RSV182 VSS RSV175 RSV176 VSS XFITXP1 XFITXN1 AP HYP0TXN0 HYP0TXP0 VSS RSV179 RSV180 VSS RSV173 RSV174 VSS VSS AN VSS VSS VSS VSS VSS XFIREFRES0 VSS VSS RSV026 VSS AM RSV099 VSS VSS RSV025 RSV185 RSV024 VSS VSS XFIREFRES1 VSS AL VSS VDDAHV VSS VDDAHV VSS VDDAHV VSS VDDAHV VSS VDDAHV AK VDDAHV VSS VDDAHV VSS VDDAHV VSS VDDAHV VSS VDDAHV VSS AJ VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV AH VDDALV VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV VSS AG VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV AF AVDDA1 VSS VDDALV VSS VDDALV VSS VDDALV VSS VDDALV VSS AE VSS CVDD VSS CVDD VSS CVDD VSS CVDD VSS CVDD AD VNWA2 VSS CVDD VSS CVDD VSS CVDD1 VSS CVDD1 VSS AC VSS CVDD VSS CVDD VSS CVDD VSS CVDD1 VSS CVDD AB CVDD VSS VDDUSB VSS CVDD VSS CVDD VSS CVDD VSS AA VSS VP VSS DVDD33 VSS CVDD VSS CVDD VSS CVDD Y VPTX VSS VPH VSS CVDD VSS CVDD VSS CVDD VSS W VSS CVDD VSS CVDD VSS CVDD1 VSS CVDD VSS CVDD V VNWA4 VSS CVDD1 VSS CVDD VSS CVDD1 VSS CVDD VSS U VSS CVDD VSS CVDD1 VSS CVDD1 VSS CVDD VSS CVDD1 T CVDD VSS CVDD1 VSS CVDD VSS CVDD VSS CVDD VSS R VSS CVDD VSS CVDD VSS CVDD VSS CVDD VSS CVDD P AVDDA6 VSS CVDD VSS CVDD VSS CVDD VSS CVDD VSS N VSS CVDD VSS CVDD VSS CVDD VSS CVDD VSS AVDDA2 M DVDD15 VSS AVDDA7 VSS AVDDA8 VSS DVDD15 AVDDA9 DVDD15 AVDDA10 L VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 K DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS J VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 VSS DVDD15 H DVDD15 VSS DVDD15 VSS DVDD15 DDR3ARQ0 DVDD15 VSS DVDD15 VSS G DDR3ABA2 DDR3ACKE0 DDR3AODT1 DDR3AVREFSSTL DDR3ACB07 DDR3AD33 DDR3AD35 DDR3AD42 DDR3AD44 DDR3AD51 F DDR3ACE1 DDR3AWE RSV029 DDR3ACB05 DDR3ACB03 DDR3AD34 DDR3AD38 DDR3AD47 DDR3AD43 DDR3AD54 E VSS DDR3AODT0 VSS DDR3ADQM8 VSS DDR3AD32 VSS DDR3AD39 VSS DDR3AD53 D DDR3ACE0 RSV027 RSV028 DDR3ACB06 DDR3ACB04 DDR3AD36 DDR3AD37 DDR3AD46 DDR3AD41 DDR3AD50 C DDR3ABA1 VSS DDR3ACAS VSS DDR3ACB01 VSS DDR3ADQM4 VSS DDR3AD40 VSS B DDR3ABA0 DDR3ARESET DDR3ADQS8P DDR3ACB02 DDR3ADQS4N DDR3AD45 DDR3ADQS5P DDR3AD49 DDR3ARAS DDR3ADQS8N DDR3ACB00 DDR3ADQS4P DDR3ADQM5 DDR3ADQS5N DDR3AD48 14 15 16 DDR3ACLKOUTN0 DDR3ACLKOUTN1 A DDR3ACKE1 DDR3ACLKOUTP0 DDR3ACLKOUTP1 11 12 13 17 18 19 20 Figure 4-4. 66AK2Hxx Pin Map Left Center Panel (B) — Bottom View 12 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 21 22 23 24 25 26 27 28 29 30 VSS RIORXN2 RIORXP2 VSS SGMII3RXN SGMII3RXP VSS SGMII0RXN SGMII0RXP VSS AW RIORXN3 RIORXP3 VSS RIORXN0 RIORXP0 VSS SGMII1RXN SGMII1RXP VSS PCIERXN1 AV VSS RIORXN1 RIORXP1 VSS SGMII2RXN SGMII2RXP VSS SGMII0TXN SGMII0TXP VSS AU RIOTXN3 RIOTXP3 VSS RIOTXN0 RIOTXP0 VSS SGMII1TXN SGMII1TXP VSS PCIETXN0 AT VSS VSS RIOTXN1 RIOTXP1 VSS SGMII2TXN SGMII2TXP VSS PCIETXN1 PCIETXP1 AR VSS RIOTXN2 RIOTXP2 VSS SGMII3TXN SGMII3TXP VSS VSS VSS VSS AP VSS VSS VSS VSS VSS VSS VSS VSS VSS PACLKSEL AN RIOREFRES VSS RSV021 SGMIIREFRES RSV023 PCIEREFRES DVDD18 RSV022 DVDD18 RSV192 AM VSS VDDAHV VSS VDDAHV VSS DVDD18 VSS DVDD18 VSS CVDD AL VDDAHV VSS VDDAHV VSS VDDAHV VSS DVDD18 VSS CVDD VSS AK VSS VDDALV VSS VDDALV VSS DVDD18 VSS CVDD VSS DVDD15 AJ VDDALV VSS VDDALV VSS VDDALV VSS CVDD VSS AVDDA4 VSS AH VSS VDDALV VSS VNWA1 VSS AVDDA5 VSS CVDD VSS DVDD15 AG VDDALV VSS VDDALV VSS CVDD VSS CVDD VSS DVDD15 VSS AF VSS CVDD VSS CVDD VSS CVDD VSS AVDDA15 VSS DVDD15 AE CVDD VSS CVDD VSS CVDD VSS CVDD AVDDA14 DVDD15 VSS AD VSS CVDD VSS CVDD VSS CVDD VSS AVDDA13 VSS DVDD15 AC CVDD VSS CVDD VSS CVDD VSS CVDD AVDDA12 DVDD15 VSS AB VSS CVDD VSS CVDD VSS CVDD VSS DVDD15 VSS DVDD15 AA CVDD VSS CVDD VSS CVDD VSS CVDD AVDDA11 DVDD15 VSS Y VSS CVDDT1 VSS CVDD VSS CVDD VSS DVDD15 VSS DVDD15 W CVDD1 VSS CVDD VSS CVDD VSS CVDD VSS DVDD15 VSS V VSS CVDDT1 VSS CVDD VSS CVDD VSS DVDD15 VSS DVDD15 U CVDD1 VSS CVDD VSS CVDD VSS CVDD VSS DVDD15 VSS T VSS CVDDT1 VSS CVDD VSS CVDD VSS DVDD15 VSS DVDD15 R CVDD VSS CVDD VSS CVDD VSS CVDD VSS DVDD15 VSS P VSS CVDD VSS CVDD VSS CVDD VSS AVDDA3 VSS DVDD18 N VPP VSS VNWA3 VSS CVDD VSS CVDD VSS DVDD18 VSS M VSS VPP VSS DVDD18 VSS DVDD18 VSS CVDD VSS DVDD18 L DVDD15 VSS DVDD15 VSS DVDD18 VSS DVDD18 VSS CVDD VSS K VSS DVDD15 VSS VSS VSS DVDD18 VSS DVDD18 VSS CVDD J DVDD15 DDR3ARQ2 DVDD15 VSS DVDD18 VSS DVDD18 VSS VSS VSS H DDR3AD55 DDR3AD57 VSS CORESEL3 VSS RSV018 VSS SPI2DOUT VSS GPIO09 G DDR3AD62 DDR3AD59 RSV013 CORESEL0 SPI0SCS0 RSV017 SPI1DIN SPI2DIN GPIO00 GPIO12 F VSS DDR3AD60 RSV014 CORESEL1 SPI2SCS3 SPI0SCS2 SPI1SCS3 VSS GPIO05 GPIO11 E DDR3ADQM6 DDR3AD63 DDR3AD58 CORESEL2 SPI2CLK SPI0SCS3 SPI1SCS2 SPI2SCS1 GPIO02 GPIO06 D DDR3AD52 VSS DDR3AD56 VSS SPI0SCS1 VSS SPI1SCS1 SPI1CLK VSS GPIO07 C DDR3ADQS6N DDR3AD61 DDR3ADQS7N RSV004 DDR3ACLKP SPI0CLK SPI1SCS0 SPI2SCS0 GPIO04 GPIO01 B DDR3ADQS6P DDR3ADQM7 DDR3ADQS7P RSV005 DDR3ACLKN SPI0DIN SPI0DOUT SPI1DOUT SPI2SCS2 GPIO08 A 21 22 23 24 25 26 27 28 29 30 Figure 4-5. 66AK2Hxx Pin Map Right Center Panel (C) — Bottom View Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 13 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 31 32 33 34 35 36 37 38 39 PCIECLKP PCIECLKN VSS SRIOSGMIICLKP SRIOSGMIICLKN RSV81 VSS VSS (NOPIN) AW PCIERXP1 VSS PASSCLKP PASSCLKN VSS RSV79 RSV77 VSS VSS AV PCIERXN0 PCIERXP0 VSS RSV008 RSV80 RSV76 RSV78 VCNTL4 VSS AU PCIETXP0 VSS XFIMDIO RSV009 RSV75 VSS RSV74 VCNTL3 VCNTL0 AT VSS MDIO VSS XFIMDCLK VCNTL5 VCNTL2 VCNTL1 DDR3BCLKP DDR3BCLKN AR MDCLK RSV193 RSV195 RSV191 VD VCL VSS RSV006 RSV007 AP VSS RSV194 DDR3BD58 DDR3BD56 VSS DDR3BD57 DDR3BD63 DDR3BDQS7P DDR3BDQS7N AN CVDD VSS VSS DDR3BD59 DDR3BD60 DDR3BD62 VSS DDR3BD61 DDR3BDQM7 AM VSS DVDD15 DDR3BD55 DDR3BD52 VSS DDR3BD53 DDR3BD54 DDR3BDQS6N DDR3BDQS6P AL DVDD15 DDR3BRQ2 VSS DDR3BDQM6 DDR3BD51 DDR3BD50 VSS DDR3BD49 DDR3BD48 AK VSS VSS DDR3BD41 DDR3BD43 VSS DDR3BD44 DDR3BD47 DDR3BDQS5N DDR3BDQS5P AJ DVDD15 DDR3BD40 VSS DDR3BD37 DDR3BD38 DDR3BD42 VSS DDR3BD46 DDR3BD45 AH VSS DDR3BD39 DDR3BDQM4 DDR3BD35 VSS DDR3BD36 DDR3BD32 DDR3BD34 DDR3BDQM5 AG DVDD15 DDR3BCB00 VSS DDR3BCB01 DDR3BCB03 DDR3BD33 VSS DDR3BDQS4P DDR3BDQS4N AF VSS DDR3BCB02 DDR3BCB04 DDR3BCB07 VSS DDR3BCB05 DDR3BDQM8 DDR3BDQS8N DDR3BDQS8P AE DVDD15 DDR3BRAS VSS DDR3BODT1 RSV030 DDR3BCB06 VSS DDR3BCLKOUTP0 DDR3BCLKOUTN0 AD DDR3BODT0 RSV031 VSS DDR3BCAS DDR3BWE DDR3BCLKOUTN1 DDR3BCLKOUTP1 AC DDR3BVREFSSTL DDR3BRESET DVDD15 RSV032 VSS DDR3BCE0 DDR3BBA2 VSS VSS DDR3BCKE1 DDR3BCKE0 AB DDR3BRQ0 DDR3BA00 DDR3BA08 DDR3BBA1 VSS DDR3BCE1 DDR3BBA0 DDR3BA14 DDR3BA11 AA DVDD15 DDR3BA09 VSS DDR3BA03 DDR3BA12 DDR3BA15 VSS DDR3BA10 DDR3BA13 Y VSS DDR3BA02 DDR3BA01 DDR3BA04 VSS DDR3BA06 DDR3BA07 DDR3BD27 DDR3BD28 W DVDD15 DDR3BD30 VSS DDR3BA05 DDR3BD24 DDR3BD31 VSS DDR3BDQS3N DDR3BDQS3P V VSS DDR3BDQM3 DDR3BD29 DDR3BD26 VSS DDR3BD25 DDR3BD21 DDR3BD23 DDR3BDQM2 U DVDD15 DDR3BD08 VSS DDR3BD16 DDR3BD18 DDR3BD22 VSS DDR3BDQS2N DDR3BDQS2P T VSS DDR3BD09 DDR3BD14 DDR3BD17 VSS DDR3BD20 DDR3BD19 DDR3BD12 DDR3BD11 R DVDD15 DDR3BRQ1 VSS DDR3BDQM1 DDR3BD10 DDR3BD15 VSS DDR3BDQS1N DDR3BDQS1P P VSS DDR3BD13 DDR3BD04 DDR3BD01 VSS DDR3BD06 DDR3BD05 DDR3BD07 DDR3BDQM0 N DVDD15 EMIFD00 VSS EMIFD13 EMIFD15 EMIFD14 DDR3BD02 DDR3BDQS0P DDR3BDQS0N M VSS DVDD15 EMIFD02 EMIFD03 EMIFD12 EMIFD11 VSS DDR3BD00 DDR3BD03 L DVDD18 VSS EMIFA07 EMIFA16 VSS EMIFD10 EMIFD06 EMIFD09 EMIFD08 K VSS DVDD18 VSS EMIFA05 EMIFA18 EMIFA21 EMIFD01 EMIFD05 EMIFD07 J CVDD VSS EMIFBE1 EMIFBE0 EMIFA06 EMIFA12 VSS EMIFA22 EMIFD04 H VSS EMIFCE1 EMIFCE0 EMIFCE2 VSS EMIFA02 EMIFA09 EMIFA14 EMIFA19 G GPIO10 RSV016 EMIFRNW EMIFA00 EMIFA17 EMIFWE EMIFA01 EMIFA10 EMIFA15 F GPIO25 GPIO14 RSV015 EMIFA04 EMIFA13 EMIFCE3 EMIFOE EMIFWAIT0 EMIFA03 E GPIO22 GPIO27 GPIO21 VSS EMIFA11 EMIFA23 VSS RSV011 EMIFWAIT1 D GPIO18 VSS GPIO28 GPIO29 EMIFA08 EMIFA20 ARMCLKP RSV010 VSS C GPIO15 GPIO19 GPIO24 GPIO31 GPIO23 GPIO30 ARMCLKN VSS VSS B GPIO13 GPIO17 GPIO20 GPIO26 GPIO03 GPIO16 VSS VSS (NOPIN) A 31 32 33 34 35 36 37 38 39 Figure 4-6. 66AK2Hxx Pin Map Right Side Panel (D) — Bottom View 14 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 4.3 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Terminal Functions The terminal functions table (Table 4-2) identifies the external signal names, the associated pin (ball) numbers, the pin type (I, O/Z, or I/O/Z), whether the pin has any internal pullup/pulldown resistors, and gives functional pin descriptions. This table is arranged by function. The power terminal functions table (Table 4-3) lists the various power supply pins and ground pins and gives functional pin descriptions. Table 4-4 shows all pins arranged by signal name. Table 4-5 shows all pins arranged by ball number. There are 17 pins that have a secondary function as well as a primary function. The secondary function is indicated with a dagger (†). For more detailed information on device configuration, peripheral selection, multiplexed/shared pins, and pullup/pulldown resistors, see Section 10.2. Use the symbol definitions in Table 4-1 when reading Table 4-2. Table 4-1. I/O Functional Symbol Definitions FUNCTIONAL SYMBOL IPD or IPU A DEFINITION Table 4-2 COLUMN HEADING Internal 100-µA pulldown or pullup is provided for this terminal. In most systems, a 1-kΩ resistor can be used to oppose the IPD/IPU. For more detailed information on pulldown/pullup resistors and situations in which external pulldown/pullup resistors are required, see Hardware Design Guide for KeyStone II Devices. IPD/IPU Analog signal Type Ground Type I Input terminal Type O Output terminal Type S Supply voltage Type Z Three-state terminal or high impedance Type GND Table 4-2. Terminal Functions — Signals and Control by Function SIGNAL NAME BALL NO. TYPE IPD/IPU DESCRIPTION ARMAVSSHARED† G24 I Down Boot strapped pin to share ARM AVS with SoC. Pin shared with CORESEL3. AVSIFSEL0† M2 I Down AVSIFSEL1† M1 I Down Default value (Boot Strapped) for SR PINMUX register (SR_PINCTL). Pins shared with TIMI0 and TIMI1. BOOTMODE_RSVD† B31 I Down BOOTMODE00† B30 I Down BOOTMODE01† D29 I Down BOOTMODE02† A35 I Down BOOTMODE03† B29 I Down BOOTMODE04† E29 I Down BOOTMODE05† D30 I Down User-defined BOOTMODE pins BOOTMODE06† C30 I Down See Section 10.1.2 for more details. BOOTMODE07† A30 I Down († Pins are secondary functions and are shared with GPIO[01:13]) BOOTMODE08† G30 I Down BOOTMODE09† F31 I Down BOOTMODE10† E30 I Down BOOTMODE11† F30 I Down BOOTMODE12† A31 I Down BOOTMODE13† F24 I User-defined BOOTMODE pins BOOTMODE14† E24 I See Section 10.1.2 for more details. BOOTMODE15† D24 I BOOTCOMPLETE AF5 OZ Boot Configuration Pins BOOTMODE reserved pin. Pin shared with GPIO15. († Pins are secondary functions and are shared with CORESEL[0:2]) Down Boot progress indication output Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 15 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU DESCRIPTION DDR3A_REMAP_EN† A36 I Down Control ARM remapping of DDR3A address space in the lower 4GB (32b space) Mode select. Secondary function. Pin shared with GPIO16. LENDIAN† F29 I Up Little-endian configuration pin. Pin shared with GPIO00. MAINPLLODSEL† E32 I Down Main PLL Output divider select. Pin shared with GPIO14. ALTCORECLKN AL2 I ALTCORECLKP AM2 I ARMCLKN B37 I ARMCLKP C37 I CORECLKSEL AL4 I Down CORESEL0 F24 I Down CORESEL1 E24 I Down CORESEL2 D24 I Down CORESEL3 G24 I Down DDR3ACLKN A25 I DDR3ACLKP B25 I DDR3BCLKN AR39 I DDR3BCLKP AR38 I HOUT AE5 OZ HYP0CLKN AT10 I HYP0CLKP AT9 I LRESET AE4 I Up Warm reset LRESETNMIEN AD4 I Up Enable for core selects HYP1CLKN AW5 I HYP1CLKP AW4 I NMI AD5 I Up Nonmaskable interrupt PACLKSEL AN30 I Down PA clock select to choose between core clock and PASSCLK pins PASSCLKN AV34 I PASSCLKP AV33 I PCIECLKN AW32 I PCIECLKP AW31 I POR AK4 I RESETFULL AD3 I Up Full reset RESET AD2 I Up Warm reset of nonisolated portion of the device RESETSTAT AC5 O Up Reset status output SRIOSGMIICLKN AW35 I SRIOSGMIICLKP AW34 I SYSCLKN AK3 I SYSCLKP AL3 I SYSCLKOUT AK1 OZ TSREFCLKN AL1 I TSREFCLKP AM1 I TSRXCLKOUT0N AP1 O TSRXCLKOUT0P AN1 O TSRXCLKOUT1N AP3 O TSRXCLKOUT1P AN3 O Clock / Reset 16 Alternate clock input to Main PLL Reference clock to drive ARM CorePac PLL Core clock select to select between SYSCLK(N|p) and ALTCORECCLK to the main PLL Select for the target core for LRESET and NMI DDR3A reference clock input to DDR PLL DDR3B reference clock input to DDR PLL Up Interrupt output pulse created by IPCGRH HyperLink reference clock to drive HyperLink0 SerDes HyperLink reference clock to drive HyperLink 1 SerDes Packet Accelerator subsystem reference clock PCIe clock input to drive PCIe SerDes Power-on reset RapidIO/SGMII reference clock to drive the RapidIO and SGMII SerDes System clock input to Main PLL (Main PLL optional vs. ALTCORECLK) Down System clock output to be used as a general-purpose output clock for debug purposes External precision clock source for SyncE SerDes recovered clock output for SyncE. SerDes recovered clock output for SyncE. Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3ADQM0 C2 OZ DDR3ADQM1 F3 OZ DDR3ADQM2 A6 OZ DDR3ADQM3 E6 OZ DDR3ADQM4 C17 OZ DDR3ADQM5 A18 OZ DDR3ADQM6 D21 OZ DDR3ADQM7 A22 OZ DDR3ADQM8 E14 OZ DDR3ADQS0P E1 IOZ DDR3ADQS0N D1 IOZ DDR3ADQS1P B3 IOZ DDR3ADQS1N C3 IOZ DDR3ADQS2P A5 IOZ DDR3ADQS2N B5 IOZ DDR3ADQS3P B7 IOZ DDR3ADQS3N A7 IOZ DDR3ADQS4P A17 IOZ DDR3ADQS4N B17 IOZ DDR3ADQS5P B19 IOZ DDR3ADQS5N A19 IOZ DDR3ADQS6P A21 IOZ DDR3ADQS6N B21 IOZ DDR3ADQS7P A23 IOZ DDR3ADQS7N B23 IOZ DDR3ADQS8P B15 IOZ DDR3ADQS8N A15 IOZ DDR3ACB00 A16 IOZ DDR3ACB01 C15 IOZ DDR3ACB02 B16 IOZ DDR3ACB03 F15 IOZ DDR3ACB04 D15 IOZ DDR3ACB05 F14 IOZ DDR3ACB06 D14 IOZ DDR3ACB07 G15 IOZ IPD/IPU DESCRIPTION DDR3A DDR3A EMIF data masks DDR3A EMIF data strobe DDR3A EMIF check bits Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 17 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3AD00 G1 IOZ DDR3AD01 H2 IOZ DDR3AD02 F1 IOZ DDR3AD03 G2 IOZ DDR3AD04 H1 IOZ DDR3AD05 E2 IOZ DDR3AD06 F2 IOZ DDR3AD07 D2 IOZ DDR3AD08 E4 IOZ DDR3AD09 F4 IOZ DDR3AD10 G3 IOZ DDR3AD11 A4 IOZ DDR3AD12 B4 IOZ DDR3AD13 H3 IOZ DDR3AD14 D3 IOZ DDR3AD15 D4 IOZ DDR3AD16 G4 IOZ DDR3AD17 H5 IOZ DDR3AD18 D5 IOZ DDR3AD19 F5 IOZ DDR3AD20 G5 IOZ DDR3AD21 D6 IOZ DDR3AD22 C5 IOZ DDR3AD23 B6 IOZ DDR3AD24 C7 IOZ DDR3AD25 F7 IOZ DDR3AD26 F6 IOZ DDR3AD27 A8 IOZ DDR3AD28 B8 IOZ DDR3AD29 G6 IOZ DDR3AD30 G7 IOZ DDR3AD31 D7 IOZ DDR3AD32 E16 IOZ DDR3AD33 G16 IOZ DDR3AD34 F16 IOZ DDR3AD35 G17 IOZ DDR3AD36 D16 IOZ DDR3AD37 D17 IOZ DDR3AD38 F17 IOZ DDR3AD39 E18 IOZ DDR3AD40 C19 IOZ DDR3AD41 D19 IOZ DDR3AD42 G18 IOZ DDR3AD43 F19 IOZ DDR3AD44 G19 IOZ DDR3AD45 B18 IOZ DDR3AD46 D18 IOZ DDR3AD47 F18 IOZ DDR3AD48 A20 IOZ 18 IPD/IPU DESCRIPTION DDR3A EMIF data bus DDR3A EMIF data bus DDR3A EMIF data bus Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3AD49 B20 IOZ DDR3AD50 D20 IOZ DDR3AD51 G20 IOZ DDR3AD52 C21 IOZ DDR3AD53 E20 IOZ DDR3AD54 F20 IOZ DDR3AD55 G21 IOZ DDR3AD56 C23 IOZ DDR3AD57 G22 IOZ DDR3AD58 D23 IOZ DDR3AD59 F22 IOZ DDR3AD60 E22 IOZ DDR3AD61 B22 IOZ DDR3AD62 F21 IOZ DDR3AD63 D22 IOZ DDR3ACE0 D11 OZ DDR3A EMIF chip enable DDR3ACE1 F11 OZ DDR3A EMIF chip enable DDR3ABA0 B11 OZ DDR3ABA1 C11 OZ DDR3ABA2 G11 OZ DDR3AA00 E8 OZ DDR3AA01 G9 OZ DDR3AA02 G8 OZ DDR3AA03 G10 OZ DDR3AA04 F9 OZ DDR3AA05 F8 OZ DDR3AA06 C9 OZ DDR3AA07 D9 OZ DDR3AA08 B9 OZ DDR3AA09 D8 OZ DDR3AA10 F10 OZ DDR3AA11 A9 OZ DDR3AA12 E10 OZ DDR3AA13 A10 OZ DDR3AA14 B10 OZ DDR3AA15 D10 OZ DDR3ACAS C13 OZ DDR3A EMIF column address strobe DDR3ARAS A14 OZ DDR3A EMIF row address strobe DDR3AWE F12 OZ DDR3A EMIF write enable DDR3ACKE0 G12 OZ DDR3A EMIF clock enable0 DDR3ACKE1 A11 OZ DDR3A EMIF clock enable1 DDR3ACLKOUTP0 A12 OZ DDR3ACLKOUTN0 B12 OZ DDR3ACLKOUTP1 A13 OZ DDR3ACLKOUTN1 B13 OZ DDR3AODT0 E12 OZ DDR3A EMIF on die termination outputs used to set termination on the SDRAMs for Rank0 DDR3AODT1 G13 OZ DDR3A EMIF on die termination outputs used to set termination on the SDRAMs for Rank1 DDR3ARESET B14 OZ DDR3A reset signal DDR3ARZQ0 H16 A PTV compensation pin for DDR3A DDR3ARZQ1 H10 A PTV compensation pin for DDR3A DDR3ARZQ2 H22 A PTV compensation pin for DDR3A IPD/IPU DESCRIPTION DDR3A EMIF data bus DDR3A EMIF bank address DDR3A EMIF address bus DDR3A EMIF output clocks to drive SDRAMs (one clock pair per SDRAM) for Rank0 DDR3A EMIF output clocks to drive SDRAMs (one clock pair per SDRAM) for Rank1 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 19 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3BDQM0 N39 OZ DDR3BDQM1 P34 OZ DDR3BDQM2 U39 OZ DDR3BDQM3 U32 OZ DDR3BDQM4 AG33 OZ DDR3BDQM5 AG39 OZ DDR3BDQM6 AK34 OZ DDR3BDQM7 AM39 OZ DDR3BDQM8 AE37 OZ DDR3BDQS0P M38 IOZ DDR3BDQS0N M39 IOZ DDR3BDQS1P P39 IOZ DDR3BDQS1N P38 IOZ DDR3BDQS2P T39 IOZ DDR3BDQS2N T38 IOZ DDR3BDQS3P V39 IOZ DDR3BDQS3N V38 IOZ DDR3BDQS4P AF38 IOZ DDR3BDQS4N AF39 IOZ DDR3BDQS5P AJ39 IOZ DDR3BDQS5N AJ38 IOZ DDR3BDQS6P AL39 IOZ DDR3BDQS6N AL38 IOZ DDR3BDQS7P AN38 IOZ DDR3BDQS7N AN39 IOZ DDR3BDQS8P AE39 IOZ DDR3BDQS8N AE38 IOZ DDR3BCB00 AF32 IOZ DDR3BCB01 AF34 IOZ DDR3BCB02 AE32 IOZ DDR3BCB03 AF35 IOZ DDR3BCB04 AE33 IOZ DDR3BCB05 AE36 IOZ DDR3BCB06 AD36 IOZ DDR3BCB07 AE34 IOZ IPD/IPU DESCRIPTION DDR3B 20 DDR3B EMIF data masks DDR3B EMIF data strobe DDR3B EMIF check bits Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3BD00 L38 IOZ DDR3BD01 N34 IOZ DDR3BD02 M37 IOZ DDR3BD03 L39 IOZ DDR3BD04 N33 IOZ DDR3BD05 N37 IOZ DDR3BD06 N36 IOZ DDR3BD07 N38 IOZ DDR3BD08 T32 IOZ DDR3BD09 R32 IOZ DDR3BD10 P35 IOZ DDR3BD11 R39 IOZ DDR3BD12 R38 IOZ DDR3BD13 N32 IOZ DDR3BD14 R33 IOZ DDR3BD15 P36 IOZ DDR3BD16 T34 IOZ DDR3BD17 R34 IOZ DDR3BD18 T35 IOZ DDR3BD19 R37 IOZ DDR3BD20 R36 IOZ DDR3BD21 U37 IOZ DDR3BD22 T36 IOZ DDR3BD23 U38 IOZ DDR3BD24 V35 IOZ DDR3BD25 U36 IOZ DDR3BD26 U34 IOZ DDR3BD27 W38 IOZ DDR3BD28 W39 IOZ DDR3BD29 U33 IOZ DDR3BD30 V32 IOZ DDR3BD31 V36 IOZ DDR3BD32 AG37 IOZ DDR3BD33 AF36 IOZ DDR3BD34 AG38 IOZ DDR3BD35 AG34 IOZ DDR3BD36 AG36 IOZ DDR3BD37 AH34 IOZ DDR3BD38 AH35 IOZ DDR3BD39 AG32 IOZ DDR3BD40 AH32 IOZ DDR3BD41 AJ33 IOZ DDR3BD42 AH36 IOZ DDR3BD43 AJ34 IOZ DDR3BD44 AJ36 IOZ DDR3BD45 AH39 IOZ IPD/IPU DESCRIPTION DDR3B EMIF data bus DDR3B EMIF data bus DDR3B EMIF data bus Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 21 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3BD46 AH38 IOZ DDR3BD47 AJ37 IOZ DDR3BD48 AK39 IOZ DDR3BD49 AK38 IOZ DDR3BD50 AK36 IOZ DDR3BD51 AK35 IOZ DDR3BD52 AL34 IOZ DDR3BD53 AL36 IOZ DDR3BD54 AL37 IOZ DDR3BD55 AL33 IOZ DDR3BD56 AN34 IOZ DDR3BD57 AN36 IOZ DDR3BD58 AN33 IOZ DDR3BD59 AM34 IOZ DDR3BD60 AM35 IOZ DDR3BD61 AM38 IOZ DDR3BD62 AM36 IOZ DDR3BD63 AN37 IOZ DDR3BCE0 AB34 OZ DDR3B EMIF chip enable DDR3BCE1 AA36 OZ DDR3B EMIF chip enable DDR3BBA0 AA37 OZ DDR3BBA1 AA34 OZ DDR3BBA2 AB35 OZ DDR3BA00 AA32 OZ DDR3BA01 W33 OZ DDR3BA02 W32 OZ DDR3BA03 Y34 OZ DDR3BA04 W34 OZ DDR3BA05 V34 OZ DDR3BA06 W36 OZ DDR3BA07 W37 OZ DDR3BA08 AA33 OZ DDR3BA09 Y32 OZ DDR3BA10 Y38 OZ DDR3BA11 AA39 OZ DDR3BA12 Y35 OZ DDR3BA13 Y39 OZ DDR3BA14 AA38 OZ DDR3BA15 Y36 OZ DDR3BCAS AC36 OZ DDR3B EMIF column address strobe DDR3BRAS AD32 OZ DDR3B EMIF row address strobe DDR3BWE AC37 OZ DDR3B EMIF write enable DDR3BCKE0 AB39 OZ DDR3B EMIF clock enable0 DDR3BCKE1 AB38 OZ DDR3B EMIF clock enable1 DDR3BCLKOUTP0 AD38 OZ DDR3BCLKOUTN0 AD39 OZ DDR3BCLKOUTP1 AC39 OZ DDR3BCLKOUTN1 AC38 OZ DDR3BODT0 AC33 OZ DDR3B EMIF on-die termination outputs used to set termination on the SDRAMs DDR3BODT1 AD34 OZ DDR3B EMIF on-die termination outputs used to set termination on the SDRAMs DDR3BRESET AC32 OZ DDR3B reset signal 22 IPD/IPU DESCRIPTION DDR3B EMIF data bus DDR3B EMIF bank address DDR3B EMIF address bus DDR3B EMIF output clocks to drive SDRAM (one clock pair for Rank0) DDR3B EMIF output clocks to drive SDRAM (one clock pair for Rank1) Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE DDR3BRZQ0 AA31 A PTV compensation pin for DDR3B DDR3BRZQ1 P32 A PTV compensation pin for DDR3B DDR3BRZQ2 AK32 A PTV compensation pin for DDR3B EMIFRW F33 O Up EMIFCE0 G33 O Up EMIFCE1 G32 O Up EMIFCE2 G34 O Up EMIFCE3 E36 O Up EMIFOE E37 O Up EMIFWE F36 O Up EMIFBE0 H34 O Up EMIFBE1 H33 O Up EMIFWAIT0 E38 I Down EMIFWAIT1 D39 I Down EMIFA00 F34 O Down EMIFA01 F37 O Down EMIFA02 G36 O Down EMIFA03 E39 O Down EMIFA04 E34 O Down EMIFA05 J34 O Down EMIFA06 H35 O Down EMIFA07 K33 O Down EMIFA08 C35 O Down EMIFA09 G37 O Down EMIFA10 F38 O Down EMIFA11 D35 O Down EMIFA12 H36 O Down EMIFA13 E35 O Down EMIFA14 G38 O Down EMIFA15 F39 O Down EMIFA16 K34 O Down EMIFA17 F35 O Down EMIFA18 J35 O Down EMIFA19 G39 O Down EMIFA20 C36 O Down EMIFA21 J36 O Down EMIFA22 H38 O Down EMIFA23 D36 O Down IPD/IPU DESCRIPTION EMIF16 EMIF control signals EMIF address EMIF address Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 23 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU EMIFD00 M32 IOZ Down EMIFD01 J37 IOZ Down EMIFD02 L33 IOZ Down EMIFD03 L34 IOZ Down EMIFD04 H39 IOZ Down EMIFD05 J38 IOZ Down EMIFD06 K37 IOZ Down EMIFD07 J39 IOZ Down EMIFD08 K39 IOZ Down EMIFD09 K38 IOZ Down EMIFD10 K36 IOZ Down EMIFD11 L36 IOZ Down EMIFD12 L35 IOZ Down EMIFD13 M34 IOZ Down EMIFD14 M36 IOZ Down EMIFD15 M35 IOZ Down EMU00 AA2 IOZ Up EMU01 AB2 IOZ Up EMU02 Y3 IOZ Up EMU03 Y4 IOZ Up EMU04 W3 IOZ Up EMU05 W4 IOZ Up EMU06 V4 IOZ Up EMU07 U4 IOZ Up EMU08 U3 IOZ Up EMU09 T3 IOZ Up EMU10 AB4 IOZ Up EMU11 AA3 IOZ Up EMU12 U5 IOZ Up EMU13 T4 IOZ Up EMU14 AB3 IOZ Up EMU15 R3 IOZ Up EMU16 T5 IOZ Up EMU17 R4 IOZ Up EMU18 AA4 IOZ Up EMU19† A32 IOZ Down EMU20† C31 IOZ Down EMU21† B32 IOZ Down EMU22† A33 IOZ Down EMU23† D33 IOZ Down EMU24† D31 IOZ Down EMU25† B35 IOZ Down EMU26† B33 IOZ Down EMU27† E31 IOZ Down EMU28† A34 IOZ Down EMU29† D32 IOZ Down EMU30† C33 IOZ Down EMU31† C34 IOZ Down EMU32† B36 IOZ Down EMU33† B34 IOZ Down DESCRIPTION EMIF data EMU 24 Terminal Configuration and Functions Emulation and trace port Emulation and trace port († Pins shared with GPIO[17:31]) Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU GPIO00 F29 IOZ Up GPIO01 B30 IOZ Down GPIO02 D29 IOZ Down GPIO03 A35 IOZ Down GPIO04 B29 IOZ Down GPIO05 E29 IOZ Down GPIO06 D30 IOZ Down GPIO07 C30 IOZ Down GPIO08 A30 IOZ Down GPIO09 G30 IOZ Down GPIO10 F31 IOZ Down GPIO11 E30 IOZ Down GPIO12 F30 IOZ Down GPIO13 A31 IOZ Down GPIO14 E32 IOZ Down GPIO15 B31 IOZ Down GPIO16 A36 IOZ Down GPIO17 A32 IOZ Down GPIO18 C31 IOZ Down GPIO19 B32 IOZ Down GPIO20 A33 IOZ Down GPIO21 D33 IOZ Down GPIO22 D31 IOZ Down GPIO23 B35 IOZ Down GPIO24 B33 IOZ Down GPIO25 E31 IOZ Down GPIO26 A34 IOZ Down GPIO27 D32 IOZ Down GPIO28 C33 IOZ Down GPIO29 C34 IOZ Down GPIO30 B36 IOZ Down GPIO31 B34 IOZ Down HYP0RXN0 AW10 I HYP0RXP0 AW11 I HYP0RXN1 AU10 I HYP0RXP1 AU11 I HYP0RXN2 AV9 I HYP0RXP2 AV10 I HYP0RXN3 AW7 I HYP0RXP3 AW8 I HYP0TXN0 AP11 O HYP0TXP0 AP12 O HYP0TXN1 AR10 O HYP0TXP1 AR11 O HYP0TXN2 AP8 O HYP0TXP2 AP9 O HYP0TXN3 AR7 O HYP0TXP3 AR8 O DESCRIPTION General-Purpose Input/Output (GPIO) GPIO GPIO HyperLink0 HyperLink0 receive data HyperLink0 transmit data Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 25 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU HYP0RXFLCLK AJ5 O Down HYP0RXFLDAT AJ4 O Down HYP0TXFLCLK AJ3 I Down HYP0TXFLDAT AG5 I Down HYP0RXPMCLK AJ2 I Down HYP0RXPMDAT AG3 I Down HYP0TXPMCLK AH5 O Down HYP0TXPMDAT AJ1 O Down HYP0REFRES AM9 A HYP1RXN0 AU7 I HYP1RXP0 AU8 I HYP1RXN1 AV6 I HYP1RXP1 AV7 I HYP1RXN2 AU4 I HYP1RXP2 AU5 I HYP1RXN3 AV3 I HYP1RXP3 AV4 I HYP1TXN0 AT6 O HYP1TXP0 AT7 O HYP1TXN1 AP5 O HYP1TXP1 AP6 O HYP1TXN2 AR4 O HYP1TXP2 AR5 O HYP1TXN3 AT3 O HYP1TXP3 AT4 O HYP1RXFLCLK AH4 O Down HYP1RXFLDAT AG2 O Down HYP1TXFLCLK AH3 I Down HYP1TXFLDAT AH2 I Down HYP1RXPMCLK AF3 I Down HYP1RXPMDAT AF4 I Down HYP1TXPMCLK AH1 O Down HYP1TXPMDAT AF2 O Down HYP1REFRES AM6 A DESCRIPTION HyperLink0 sideband signals HyperLink0 SerDes reference resistor input (3 kΩ ±1%) HyperLink1 HyperLink1 receive data HyperLink1 transmit data HyperLink1 sideband signals HyperLink1 SerDes reference resistor input (3 kΩ ±1%) I2C SCL0 N1 IOZ I2C0 clock SCL1 N4 IOZ I2C1 clock SCL2 P4 IOZ I2C2 clock SDA0 P3 IOZ I2C0 data SDA1 N2 IOZ I2C1 data SDA2 N3 IOZ I2C2 data TCK AE1 I Up JTAG clock input TDI AG1 I Up JTAG data input TDO AF1 OZ Up JTAG data output TMS AE2 I Up JTAG test mode input TRST AD1 I Down JTAG reset MDCLK AP31 O Down MDIO clock JTAG MDIO 26 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU DESCRIPTION MDIO AR32 IOZ Up MDIO data PCIERXN0 AU31 I PCIERXP0 AU32 I PCIERXN1 AV30 I PCIERXP1 AV31 I PCIETXN0 AT30 O PCIETXP0 AT31 O PCIETXN1 AR29 O PCIETXP1 AR30 O PCIEREFRES AM26 A PCIe PCIexpress lane 0 receive data PCIexpress lane 1 receive data PCIexpress lane 0 transmit data PCIexpress lane 1 transmit data PCIexpress SerDes reference resistor input (3 kΩ ±1%) Serial RapidIO RIORXN0 AV24 I RIORXP0 AV25 I RIORXN1 AU22 I RIORXP1 AU23 I RIORXN2 AW22 I RIORXP2 AW23 I RIORXN3 AV21 I RIORXP3 AV22 I RIOTXN0 AT24 O RIOTXP0 AT25 O RIOTXN1 AR23 O RIOTXP1 AR24 O RIOTXN2 AP22 O RIOTXP2 AP23 O RIOTXN3 AT21 O RIOTXP3 AT22 O RIOREFRES AM21 A SGMII0RXN AW28 I SGMII0RXP AW29 I SGMII0TXN AU28 O SGMII0TXP AU29 O SGMII1RXN AV27 I SGMII1RXP AV28 I SGMII1TXN AT27 O SGMII1TXP AT28 O SGMII2RXN AU25 I SGMII2RXP AU26 I SGMII2TXN AR26 O SGMII2TXP AR27 O SGMII3RXN AW25 I SGMII3RXP AW26 I SGMII3TXN AP25 O SGMII3TXP AP26 O SGMIIREFRES AM24 A VCL AP36 IOZ Serial RapidIO lane 0 receive data Serial RapidIO lane 1 receive data Serial RapidIO lane 2 receive data Serial RapidIO lane 3 receive data Serial RapidIO lane 0 transmit data Serial RapidIO lane 1 transmit data Serial RapidIO lane 2 transmit data Serial RapidIO lane 3 transmit data Serial RapidIO SerDes reference resistor input (3 kΩ ±1%) SGMII Ethernet MAC SGMII port 0 receive data Ethernet MAC SGMII port 0 transmit data Ethernet MAC SGMII port 1 receive data Ethernet MAC SGMII port 1 transmit data Ethernet MAC SGMII port 2 receive data Ethernet MAC SGMII port 2 transmit data Ethernet MAC SGMII port 3 receive data Ethernet MAC SGMII port 3 transmit data SGMII SerDes reference resistor input (3 kΩ ±1%) SmartReflex Voltage control I2C clock Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 27 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE VCNTL0 AT39 OZ VCNTL1 AR37 OZ VCNTL2 AR36 OZ VCNTL3 AT38 OZ VCNTL4 AU38 OZ VCNTL5 AR35 OZ VD AP35 IOZ SPI0CLK B26 OZ Down SPI0 clock SPI0DIN A26 I Down SPI0 data in SPI0DOUT A27 OZ Down SPI0 data out SPI0SCS0 F25 OZ Up SPI0 interface enable 0 SPI0SCS1 C25 OZ Up SPI0 interface enable 1 SPI0SCS2 E26 OZ Up SPI0 interface enable 2 SPI0SCS3 D26 OZ Up SPI0 interface enable 3 SPI1CLK C28 OZ Down SPI1 clock SPI1DIN F27 I Down SPI1 data in SPI1DOUT A28 OZ Down SPI1 data out SPI1SCS0 B27 OZ Up SPI1 interface enable 0 SPI1SCS1 C27 OZ Up SPI1 interface enable 1 SPI1SCS2 D27 OZ Up SPI1 interface enable 2 SPI1SCS3 E27 OZ Up SPI1 interface enable 3 SPI2CLK D25 OZ Down SPI2 clock SPI2DIN F28 I Down SPI2 data in SPI2DOUT G28 OZ Down SPI2 data out SPI2SCS0 B28 OZ Up SPI2 interface enable 0 SPI2SCS1 D28 OZ Up SPI2 interface enable 1 SPI2SCS2 A29 OZ Up SPI2 interface enable 2 SPI2SCS3 E25 OZ Up SPI2 interface enable 3 TSCOMPOUT AB1 O Down IEEE 1588 compare output. TSPUSHEVT0 AC2 IOZ Down PPS push event from GPS for IEEE 1588 TSPUSHEVT1 AC1 IOZ Down Push event from BCN for IEEE 1588 TSSYNCEVT AC3 O Down IEEE 1588 sync event output. TIMI0 M2 I Down TIMI1 M1 I Down TIMO0 M3 OZ Down TIMO1 M4 OZ Down UART0CTS L1 I Down UART0RTS L4 OZ Down UART0RXD K4 I Down UART0TXD K2 OZ Down IPD/IPU DESCRIPTION Voltage control outputs to variable core power supply Voltage control I2C data SPI0 SPI1 SPI2 Sync-Ethernet / IEEE 1588 Timer Timer inputs Timer outputs UART0 28 Terminal Configuration and Functions UART0 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE IPD/IPU UART1CTS K1 I Down UART1RTS M5 OZ Down UART1RXD L2 I Down UART1TXD K3 OZ Down USBCLKM V2 I USBCLKP W2 I USBDM T2 IOZ USBDP U2 IOZ USBDRVVBUS L3 O USBID0 R1 A USBRX0M Y1 I USBRX0P W1 I USBTX0M V1 O USBTX0P U1 O USBVBUS T1 A Connect to VBUS pin on USB connector through protection switch USBRESREF AA1 P Reference resistor connection for USB PHY XFICLKP AU19 I XFICLKN AU20 I XFIMDCLK AR34 O Down XFI MDIO clock XFIMDIO AT33 IOZ Up XFI MDIO data XFIRXN0 AV19 I XFIRXP0 AV18 I XFITXN0 AT19 O XFITXP0 AT18 O XFIRXN1 AW20 I XFIRXP1 AW19 I XFITXN1 AR20 O XFITXP1 AR19 O XFIREFRES0 AN16 A XFI SerDes reference resistor input (3 kΩ ±1%) XFIREFRES1 AM19 A XFI SerDes reference resistor input (3 kΩ ±1%) RSV000 P2 OZ Down Reserved — leave unconnected RSV001 P1 OZ Down Reserved — leave unconnected RSV002 AN4 O Reserved — leave unconnected RSV003 AM4 O Reserved — leave unconnected RSV004 B24 O Reserved — leave unconnected RSV005 A24 O Reserved — leave unconnected RSV006 AP38 O Reserved — leave unconnected RSV007 AP39 O Reserved — leave unconnected RSV008 AU34 O Reserved — leave unconnected RSV009 AT34 O Reserved — leave unconnected RSV010 C38 O Reserved — leave unconnected RSV011 D38 O RSV012 AK5 OZ RSV013 F23 A GND RSV014 E23 A Reserved — leave unconnected RSV015 E33 A Reserved — leave unconnected RSV016 F32 A Reserved — leave unconnected DESCRIPTION UART1 UART1 USB USB ref clock USB DUSB D+ Down Used to enable an external charge pump to provide +5V on the VBUS pin of the USB connector. USB ID USB receive data USB transmit data XFI (66AK2H14 only) XFI reference clock to drive the XFI SerDes Ethernet MAC XFI port 0 receive data Ethernet MAC XFI port 0 transmit data Ethernet MAC XFI port 1 receive data Ethernet MAC XFI port 1 transmit data Reserved Reserved — leave unconnected Down Reserved — leave unconnected Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 29 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE RSV017 F26 A Reserved — leave unconnected RSV018 G26 A Reserved — leave unconnected RSV019 AN10 A Reserved — leave unconnected RSV020 AM7 A Reserved — leave unconnected RSV021 AM23 A Reserved — leave unconnected RSV022 AM28 A Reserved — leave unconnected RSV023 AM25 A Reserved — leave unconnected RSV024 AM16 A Reserved — leave unconnected RSV025 AM14 A Reserved — leave unconnected RSV026 AN19 A Reserved — leave unconnected RSV027 D12 OZ Reserved — leave unconnected RSV028 D13 OZ Reserved — leave unconnected RSV029 F13 A Reserved — leave unconnected RSV030 AD35 OZ Reserved — leave unconnected RSV031 AC34 OZ Reserved — leave unconnected RSV032 AB32 A Reserved — leave unconnected RSV060 (66AK2H12/06 only) AV19 I Reserved — leave unconnected RSV061 (66AK2H12/06 only) AV18 I Reserved — leave unconnected RSV062 (66AK2H12/06 only) AT19 O Reserved — leave unconnected RSV063 (66AK2H12/06 only) AT18 O Reserved — leave unconnected RSV064 (66AK2H12/06 only) AW20 I Reserved — leave unconnected RSV065 (66AK2H12/06 only) AW19 I Reserved — leave unconnected RSV066 (66AK2H12/06 only) AR20 O Reserved — leave unconnected RSV067 (66AK2H12/06 only) AR19 O Reserved — leave unconnected RSV068 (66AK2H12/06 only) AN16 A Reserved — leave unconnected RSV069 (66AK2H12/06 only) AM19 A Reserved — leave unconnected RSV070 (66AK2H12/06 only) AU19 I Reserved — leave unconnected RSV071 (66AK2H12/06 only) AU20 I Reserved — leave unconnected RSV072 (66AK2H12/06 only) AT33 IOZ Up Reserved — leave unconnected RSV073 (66AK2H12/06 only) AR34 O Down Reserved — leave unconnected RSV074 AT37 IOZ Reserved — leave unconnected RSV075 AT35 IOZ Reserved — leave unconnected RSV076 AU36 OZ Reserved — leave unconnected RSV077 AV37 OZ Reserved — leave unconnected RSV078 AU37 OZ Reserved — leave unconnected RSV079 AV36 OZ Reserved — leave unconnected RSV080 AU35 OZ Reserved — leave unconnected RSV081 AW36 OZ Reserved — leave unconnected RSV099 AM11 A Reserved — leave unconnected RSV161 AW16 I Reserved — leave unconnected RSV162 AW17 I Reserved — leave unconnected 30 IPD/IPU Terminal Configuration and Functions DESCRIPTION Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-2. Terminal Functions — Signals and Control by Function (continued) SIGNAL NAME BALL NO. TYPE RSV163 AU16 I Reserved — leave unconnected RSV164 AU17 I Reserved — leave unconnected RSV165 AV15 I Reserved — leave unconnected RSV166 AV16 I Reserved — leave unconnected RSV167 AW13 I Reserved — leave unconnected RSV168 AW14 I Reserved — leave unconnected RSV169 AU13 I Reserved — leave unconnected RSV170 AU14 I Reserved — leave unconnected RSV171 AV12 I Reserved — leave unconnected RSV172 AV13 I Reserved — leave unconnected RSV173 AP17 O Reserved — leave unconnected RSV174 AP18 O Reserved — leave unconnected RSV175 AR16 O Reserved — leave unconnected RSV176 AR17 O Reserved — leave unconnected RSV177 AT15 O Reserved — leave unconnected RSV178 AT16 O Reserved — leave unconnected RSV179 AP14 O Reserved — leave unconnected RSV180 AP15 O Reserved — leave unconnected RSV181 AR13 O Reserved — leave unconnected RSV182 AR14 O Reserved — leave unconnected RSV183 AT12 O Reserved — leave unconnected RSV184 AT13 O Reserved — leave unconnected RSV185 AM15 A Reserved — leave unconnected RSV186 AR2 I Reserved — leave unconnected RSV187 AP2 I RSV188 AC4 OZ RSV189 AR1 I RSV190 AT1 I RSV191 AP34 I Down Reserved — leave unconnected RSV192 AM30 I Down Reserved — leave unconnected RSV193 AP32 OZ Down Reserved — leave unconnected RSV194 AN32 OZ Down Reserved — leave unconnected RSV195 AP33 IOZ Up Reserved — leave unconnected IPD/IPU DESCRIPTION Reserved — leave unconnected Down Reserved — leave unconnected Reserved — leave unconnected Reserved — leave unconnected Table 4-3. Terminal Functions — Power and Ground SUPPLY BALL NO. VOLTS DESCRIPTION AVDDA1 AF11 1.8 V C66x CorePac PLL supply AVDDA2 N20 1.8 V DDR3A PLL supply AVDDA3 N28 1.8 V ARM CorePac PLL supply AVDDA4 AH29 1.8 V DDR3B PLL supply AVDDA5 AG26 1.8 V Network Coprocessor PLL supply AVDDA6 P11 1.8 V DDRA DLL supply AVDDA7 M13 1.8 V DDRA DLL supply AVDDA8 M15 1.8 V DDRA DLL supply AVDDA9 M18 1.8 V DDRA DLL supply AVDDA10 M20 1.8 V DDRA DLL supply AVDDA11 Y28 1.8 V DDRB DLL supply AVDDA12 AB28 1.8 V DDRB DLL supply AVDDA13 AC28 1.8 V DDRB DLL supply AVDDA14 AD28 1.8 V DDRB DLL supply Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 31 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-3. Terminal Functions — Power and Ground (continued) SUPPLY BALL NO. VOLTS DESCRIPTION AVDDA15 AE28 1.8 V DDRB DLL supply CVDD H31, J30, K29, L6, L28, M7, M9, M25, M27, N6, N8, N10, N12, N14, N16, N18, N22, N24, N26, P7, P9, P13, P15, P17, P19, P21, P23, P25, P27, R8, R10, R12, R14, R16, R18, R20, R24, R26, T9, T11, T15, T17, T19, T23, T25, T27, U8, U10, U12, U18, U24, U26, V9, V15, V19, V23, V25, V27, W8, W10, W12, W14, W18, W20, W24, W26, Y9, Y15, Y17, Y19, Y21, Y23, Y25, Y27, AA8, AA10, AA16, AVS AA18, AA20, AA22, AA24, AA26, AB9, AB11, AB15, AB17, AB19, AB21, AB23, AB25, AB27, AC8, AC10, AC12, AC14, AC16, AC20, AC22, AC24, AC26, AD9, AD13, AD15, AD21, AD23, AD25, AD27, AE8, AE10, AE12, AE14, AE16, AE18, AE20, AE22, AE24, AE26, AF9, AF25, AF27, AG8, AG10, AG28, AH9, AH27, AJ8, AJ10, AJ28, AK7, AK9, AK29, AL6 , AL8, AL30, AM5, AM31 SmartReflex DSP core supply voltage. CVDD1 T13, T21, U14, U16, U20, V13, V17, V21, W16, AC18, AD17, AD19 0.95 V Core supply voltage for memory array CVDDT1 R22, U22, W22 0.95 V Cortex-A15 processor fixed core memory supply voltage DDR3AVREFSSTL G14 0.75 V 0.75-V DDR3A reference voltage DDR3BVREFSSTL AC31 0.75 V 0.75-V DDR3B reference voltage DVDD15 H7, H9, H11, H13, H15, H17, H19, H21, H23, J6, J8, J10, J12, J14, J16, J18, J20, J22, K7, K9, K11, K13, K15, K17, K19, K21, K23, L8, L10, L12, L14, L16, L18, L20, L32, M11, 1.35 V / M17, M19, M31, P29, P31, R28, R30, T29, T31, U28, U30, 1.35-V / 1.5-V DDR IO supply 1.5 V V29, V31, W28, W30, Y29, Y31, AA28, AA30, AB29, AB31, AC30, AD29, AD31, AE30, AF29, AF31, AG30, AH31, AJ30, AK31, AL32 DVDD18 H25, H27, J26, J28, J32, K25, K27, K31, L24, L26, L30, M29, N30, R6, T7, U6, V5, V7, W6, Y5, Y7, AA6, AB5, AB7, 1.8 V AC6, AD7, AE6, AF7, AG6, AJ26, AK27, AL26, AL28, AM27, AM29 1.8-V IO supply DVDD33 AA14 3.3 V 3.3-V USB supply VDDAHV AK11, AK13, AK15, AK17, AK19, AK21, AK23, AK25, AL10, AL12, AL14, AL16, AL18, AL20, AL22, AL24 1.8 V SerDes IO supply VDDALV AF13, AF15, AF17, AF19, AF21, AF23, AG12, AG14, AG16, AG18, AG20, AG22, AH11, AH13, AH15, AH17, AH19, AH21, AH23, AH25, AJ12, AJ14, AJ16, AJ18, AJ20, AJ22, AJ24 0.85 V SerDes low voltage VDDUSB AB13 0.85 V SerDes digiital IO supply VNWA1 AG24 0.95 V Fixed Nwell supply VNWA2 AD11 0.95 V Fixed Nwell supply VNWA3 M23 0.95 V Fixed Nwell supply VNWA4 V11 0.95 V Fixed Nwell supply VP AA12 0.85 V Filtered .85 V USB supply VPH Y13 3.3 V Filtered 3.3 V USB supply VPP L22, M21 VPTX Y11 32 Leave unconnected 0.85 V Terminal Configuration and Functions Filtered 0.85-V USB supply Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-3. Terminal Functions — Power and Ground (continued) SUPPLY BALL NO. VSS A2, A3, A37, A38, B1, B2, B38, B39, C1, C4, C6, C8, C10, C12, C14, C16, C18, C20, C22, C24, C26, C29, C32, C39, D34, D37, E3, E5, E7, E9, E11, E13, E15, E17, E19, E21, E28, G23, G25, G27, G29, G31, G35, H4, H6, H8, H12, H14, H18, H20, H24, H26, H28, H29, H30, H32, H37, J1, J2, J3, J4, J5, J7, J9, J11, J13, J15, J17, J19, J21, J23, J24, J25, J27, J29, J31, J33, K5, K6, K8, K10, K12, K14, K16, K18, K20, K22, K24, K26, K28, K30, K32, K35, L5, L7, L9, L11, L13, L15, L17, L19, L21, L23, L25, L27, L29, L31, L37, M6, M8, M10, M12, M14, M16, M22, M24, M26, M28, M30, M33, N5, N7, N9, N11, N13, N15, N17, N19, N21, N23, N25, N27, N29, N31, N35, P5, P6, P8, P10, P12, P14, P16, P18, P20, P22, P24, P26, P28, P30, P33, P37, R2, R5, R7, R9, R11, R13, R15, R17, R19, R21, R23, R25, R27, R29, R31, R35, T6, T8, T10, T12, T14, T16, T18, T20, T22, T24, T26, T28, T30, T33, T37, U7, U9, U11, U13, U15, U17, U19, U21, U23, U25, U27, U29, U31, U35, V3, V6, V8, V10, V12, V14, V16, V18, V20, V22, V24, V26, V28, V30, V33, V37, W5, W7, W9, W11, W13, W15, W17, W19, W21, W23, W25, W27, W29, W31, W35, Y2, Y6, Y8, Y10, Y12, Y14, Y16, Y18, Y20, Y22, Y24, Y26, Y30, Y33, Y37, AA5, AA7, AA9, AA11, AA13, AA15, AA17, AA19, AA21, AA23, AA25, AA27, AA29, AA35, AB6, AB8, AB10, AB12, AB14, AB16, AB18, AB20, AB22, AB24, AB26, AB30, AB33, AB36, AB37, AC7, AC9, AC11, AC13, AC15, AC17, AC19, AC21, AC23, AC25, AC27, AC29, AC35, AD6, AD8, AD10, AD12, AD14, AD16, AD18, AD20, AD22, AD24, GND AD26, AD30, AD33, AD37, AE3, AE7, AE9, AE11, AE13, AE15, AE17, AE19, AE21, AE23, AE25, AE27, AE29, AE31, AE35, AF6, AF8, AF10, AF12, AF14, AF16, AF18, AF20, AF22, AF24, AF26, AF28, AF30, AF33, AF37, AG4, AG7, AG9, AG11, AG13, AG15, AG17, AG19, AG21, AG23, AG25, AG27, AG29, AG31, AG35, AH6, AH7, AH8, AH10, AH12, AH14, AH16, AH18, AH20, AH22, AH24, AH26, AH28, AH30, AH33, AH37, AJ6, AJ7, AJ9, AJ11, AJ13, AJ15, AJ17, AJ19, AJ21, AJ23, AJ25, AJ27, AJ29, AJ31, AJ32, AJ35, AK2, AK6, AK8, AK10, AK12, AK14, AK16, AK18, AK20, AK22, AK24, AK26, AK28, AK30, AK33, AK37, AL5, AL7, AL9, AL11, AL13, AL15, AL17, AL19, AL21, AL23, AL25, AL27, AL29, AL31, AL35, AM3, AM8, AM10, AM12, AM13, AM17, AM18, AM20, AM22, AM32, AM33, AM37, AN2, AN5, AN6, AN7, AN8, AN9, AN11, AN12, AN13, AN14, AN15, AN17, AN18, AN20, AN21, AN22, AN23, AN24, AN25, AN26, AN27, AN28, AN29, AN31, AN35, AP4, AP7, AP10, AP13, AP16, AP19, AP20, AP21, AP24, AP27, AP28, AP29, AP30, AP37, AR3, AR6, AR9, AR12, AR15, AR18, AR21, AR22, AR25, AR28, AR31, AR33, AT2, AT5, AT8, AT11, AT14, AT17, AT20, AT23, AT26, AT29, AT32, AT36, AU1, AU2, AU3, AU6, AU9, AU12, AU15, AU18, AU21, AU24, AU27, AU30, AU33, AU39, AV1, AV2, AV5, AV8, AV11, AV14, AV17, AV20, AV23, AV26, AV29 , AV32, AV35, AV38, AV39, AW2, AW3, AW6, AW9, AW12, AW15, AW18, AW21, AW24, AW27, AW30, AW33, AW37, AW38 VOLTS DESCRIPTION Ground Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 33 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-4. Terminal Functions — By Signal Name SIGNAL NAME BALL NUMBER (nopin) A1 SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER DDR3ACB05 F14 DDR3ACB06 D14 CVDD H31, J30, K29, L6, L28, M7, M9, M25, M27, N6, N8, N10, N12, N14, N16, N18, N22, N24, N26, P7, P9, P13, P15, P17, P19, P21, P23, P25, P27, R8, R10, R12 (nopin) A39 (nopin) AW1 DDR3ACB07 (nopin) AW39 G15 DDR3ACE0 ALTCORECLKN AL2 D11 R14, R16, R18, R20, R24, R26, T9, T11, T15, T17, T19, T23, T25, T27, U8, U10, U12, U18, U24, U26, V9, V15, V19, V23, V25, V27, W8, W10, W12, W14, W18 DDR3ACE1 ALTCORECLKP AM2 F11 DDR3ACKE0 ARMCLKN B37 G12 DDR3ACKE1 ARMCLKP C37 A11 DDR3ACLKN A25 ARMAVSSHARED† G24 AVDDA1 AF11 W20, W24, W26, Y9, Y15, Y17, Y19, Y21, Y23, Y25, Y27, AA8, AA10, AA16, AA18, AA20, AA22, AA24, AA26, AB9, AB11, AB15, AB17, AB19, AB21, AB23, AB25 DDR3ACLKOUTN0 B12 DDR3ACLKOUTN1 AVDDA2 N20 B13 DDR3ACLKOUTP0 AVDDA3 N28 A12 DDR3ACLKOUTP1 AVDDA4 AH29 A13 DDR3ACLKP AVDDA5 AG26 B25 DDR3AD00 AVDDA6 P11 G1 DDR3AD01 AVDDA7 M13 H2 DDR3AD02 AVDDA8 M15 F1 DDR3AD03 AVDDA9 M18 G2 DDR3AD04 AVDDA10 M20 H1 DDR3AD05 AVDDA11 Y28 E2 DDR3AD06 AVDDA12 AB28 F2 DDR3AD07 D2 CVDD1 T13, T21, U14, U16, U20, V13, V17, V21, W16, AC18, AD17, AD19 AVDDA13 AC28 DDR3AD08 AVDDA14 E4 AD28 CVDDT1 R22, U22, W22 DDR3AD09 F4 AVDDA15 AE28 DDR3A_REMAP_EN† A36 DDR3AD10 G3 AVSIFSEL0† M2 DDR3AA00 E8 DDR3AD11 A4 AVSIFSEL1† M1 DDR3AA01 G9 DDR3AD12 B4 BOOTMODE_RSVD† B31 DDR3AA02 G8 DDR3AD13 H3 BOOTMODE00† B30 DDR3AA03 G10 DDR3AD14 D3 BOOTMODE01† D29 DDR3AA04 F9 DDR3AD15 D4 BOOTMODE02† A35 DDR3AA05 F8 DDR3AD16 G4 BOOTMODE03† B29 DDR3AA06 C9 DDR3AD17 H5 BOOTMODE04† E29 DDR3AA07 D9 DDR3AD18 D5 BOOTMODE05† D30 DDR3AA08 B9 DDR3AD19 F5 BOOTMODE06† C30 DDR3AA09 D8 DDR3AD20 G5 BOOTMODE07† A30 DDR3AA10 F10 DDR3AD21 D6 BOOTMODE08† G30 DDR3AA11 A9 DDR3AD22 C5 BOOTMODE09† F31 DDR3AA12 E10 DDR3AD23 B6 BOOTMODE10† E30 DDR3AA13 A10 DDR3AD24 C7 BOOTMODE11† F30 DDR3AA14 B10 DDR3AD25 F7 BOOTMODE12† A31 DDR3AA15 D10 DDR3AD26 F6 BOOTMODE13† F24 DDR3ABA0 B11 DDR3AD27 A8 BOOTMODE14† E24 DDR3ABA1 C11 DDR3AD28 B8 BOOTMODE15† D24 DDR3ABA2 G11 DDR3AD29 G6 BOOTCOMPLETE AF5 DDR3ACAS C13 DDR3AD30 G7 CORECLKSEL AL4 DDR3ACB00 A16 DDR3AD31 D7 CORESEL0 F24 DDR3ACB01 C15 DDR3AD32 E16 CORESEL1 E24 DDR3ACB02 B16 DDR3AD33 G16 CORESEL2 D24 DDR3ACB03 F15 DDR3AD34 F16 CORESEL3 G24 DDR3ACB04 D15 DDR3AD35 G17 CVDD CVDD CVDD CVDD 34 Terminal Configuration and Functions AB27, AC8, AC10, AC12, AC14, AC16, AC20, AC22, AC24, AC26, AD9, AD13, AD15, AD21, AD23, AD25, AD27, AE8, AE10, AE12, AE14, AE16, AE18, AE20 AE22, AE24, AE26, AF9, AF25, AF27, AG8, AG10, AG28, AH9, AH27, AJ8, AJ10, AJ28, AK7, AK9, AK29, AL6, , AL8, AL30, AM5, AM31 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-4. Terminal Functions — By Signal Name (continued) SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER DDR3AD36 D16 DDR3ADQS7P A23 DDR3BD02 M37 DDR3AD37 D17 DDR3ADQS8N A15 DDR3BD03 L39 DDR3AD38 F17 DDR3ADQS8P B15 DDR3BD04 N33 DDR3AD39 E18 DDR3AODT0 E12 DDR3BD05 N37 DDR3AD40 C19 DDR3AODT1 G13 DDR3BD06 N36 DDR3AD41 D19 DDR3ARAS A14 DDR3BD07 N38 DDR3AD42 G18 DDR3ARESET B14 DDR3BD08 T32 DDR3AD43 F19 DDR3ARZQ0 H16 DDR3BD09 R32 DDR3AD44 G19 DDR3ARZQ1 H10 DDR3BD10 P35 DDR3AD45 B18 DDR3ARZQ2 H22 DDR3BD11 R39 DDR3AD46 D18 DDR3AVREFSSTL G14 DDR3BD12 R38 DDR3AD47 F18 DDR3AWE F12 DDR3BD13 N32 DDR3AD48 A20 DDR3BA00 AA32 DDR3BD14 R33 DDR3AD49 B20 DDR3BA01 W33 DDR3BD15 P36 DDR3AD50 D20 DDR3BA02 W32 DDR3BD16 T34 DDR3AD51 G20 DDR3BA03 Y34 DDR3BD17 R34 DDR3AD52 C21 DDR3BA04 W34 DDR3BD18 T35 DDR3AD53 E20 DDR3BA05 V34 DDR3BD19 R37 DDR3AD54 F20 DDR3BA06 W36 DDR3BD20 R36 DDR3AD55 G21 DDR3BA07 W37 DDR3BD21 U37 DDR3AD56 C23 DDR3BA08 AA33 DDR3BD22 T36 DDR3AD57 G22 DDR3BA09 Y32 DDR3BD23 U38 DDR3AD58 D23 DDR3BA10 Y38 DDR3BD24 V35 DDR3AD59 F22 DDR3BA11 AA39 DDR3BD25 U36 DDR3AD60 E22 DDR3BA12 Y35 DDR3BD26 U34 DDR3AD61 B22 DDR3BA13 Y39 DDR3BD27 W38 DDR3AD62 F21 DDR3BA14 AA38 DDR3BD28 W39 DDR3AD63 D22 DDR3BA15 Y36 DDR3BD29 U33 DDR3ADQM0 C2 DDR3BBA0 AA37 DDR3BD30 V32 DDR3ADQM1 F3 DDR3BBA1 AA34 DDR3BD31 V36 DDR3ADQM2 A6 DDR3BBA2 AB35 DDR3BD32 AG37 DDR3ADQM3 E6 DDR3BCAS AC36 DDR3BD33 AF36 DDR3ADQM4 C17 DDR3BCB00 AF32 DDR3BD34 AG38 DDR3ADQM5 A18 DDR3BCB01 AF34 DDR3BD35 AG34 DDR3ADQM6 D21 DDR3BCB02 AE32 DDR3BD36 AG36 DDR3ADQM7 A22 DDR3BCB03 AF35 DDR3BD37 AH34 DDR3ADQM8 E14 DDR3BCB04 AE33 DDR3BD38 AH35 DDR3ADQS0N D1 DDR3BCB05 AE36 DDR3BD39 AG32 DDR3ADQS0P E1 DDR3BCB06 AD36 DDR3BD40 AH32 DDR3ADQS1N C3 DDR3BCB07 AE34 DDR3BD41 AJ33 DDR3ADQS1P B3 DDR3BCE0 AB34 DDR3BD42 AH36 DDR3ADQS2N B5 DDR3BCE1 AA36 DDR3BD43 AJ34 DDR3ADQS2P A5 DDR3BCKE0 AB39 DDR3BD44 AJ36 DDR3ADQS3N A7 DDR3BCKE1 AB38 DDR3BD45 AH39 DDR3ADQS3P B7 DDR3BCLKN AR39 DDR3BD46 AH38 DDR3ADQS4N B17 DDR3BCLKOUTN0 AD39 DDR3BD47 AJ37 DDR3ADQS4P A17 DDR3BCLKOUTN1 AC38 DDR3BD48 AK39 DDR3ADQS5N A19 DDR3BCLKOUTP0 AD38 DDR3BD49 AK38 DDR3ADQS5P B19 DDR3BCLKOUTP1 AC39 DDR3BD50 AK36 DDR3ADQS6N B21 DDR3BCLKP AR38 DDR3BD51 AK35 DDR3ADQS6P A21 DDR3BD00 L38 DDR3BD52 AL34 DDR3ADQS7N B23 DDR3BD01 N34 DDR3BD53 AL36 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 35 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-4. Terminal Functions — By Signal Name (continued) SIGNAL NAME BALL NUMBER DDR3BD54 AL37 SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER EMIFD09 K38 EMIFD10 K36 DVDD15 L32, M11, M17, M19, M31, P29, P31, R28, R30, T29, T31, U28, U30, V29, V31, W28, W30, Y29, Y31, AA28, AA30, AB29, AB31, AC30, AD29, AD31, AE30, AF29 DDR3BD55 AL33 DDR3BD56 AN34 EMIFD11 DDR3BD57 AN36 L36 EMIFD12 DDR3BD58 AN33 L35 AF31, AG30, AH31, AJ30, AK31, AL32 EMIFD13 DDR3BD59 AM34 M34 EMIFD14 DDR3BD60 AM35 M36 H25, H27, J26, J28, J32, K25, K27, K31, L24, L26, L30, M29, N30, R6, T7, U6, V5, V7, W6, Y5, Y7, AA6, AB5, AB7, AC6, AD7, AE6, AF7, AG6, AJ26, AK27, AL26, AL28, AM27, AM29 EMIFD15 DDR3BD61 AM38 M35 EMIFOE DDR3BD62 AM36 E37 EMIFRNW DDR3BD63 AN37 F33 EMIFWAIT0 DDR3BDQM0 N39 E38 DVDD33 AA14 EMIFWAIT1 DDR3BDQM1 D39 P34 EMIFA00 F34 EMIFWE F36 DDR3BDQM2 U39 EMIFA01 F37 EMU00 AA2 DDR3BDQM3 U32 EMIFA02 G36 EMU01 AB2 DDR3BDQM4 AG33 EMIFA03 E39 EMU02 Y3 DDR3BDQM5 AG39 EMIFA04 E34 EMU03 Y4 DDR3BDQM6 AK34 EMIFA05 J34 EMU04 W3 DDR3BDQM7 AM39 EMIFA06 H35 EMU05 W4 DDR3BDQM8 AE37 EMIFA07 K33 EMU06 V4 DDR3BDQS0N M39 EMIFA08 C35 EMU07 U4 DDR3BDQS0P M38 EMIFA09 G37 EMU08 U3 DDR3BDQS1N P38 EMIFA10 F38 EMU09 T3 DDR3BDQS1P P39 EMIFA11 D35 EMU10 AB4 DDR3BDQS2N T38 EMIFA12 H36 EMU11 AA3 DDR3BDQS2P T39 EMIFA13 E35 EMU12 U5 DDR3BDQS3N V38 EMIFA14 G38 EMU13 T4 DDR3BDQS3P V39 EMIFA15 F39 EMU14 AB3 DDR3BDQS4N AF39 EMIFA16 K34 EMU15 R3 DDR3BDQS4P AF38 EMIFA17 F35 EMU16 T5 DDR3BDQS5N AJ38 EMIFA18 J35 EMU17 R4 DDR3BDQS5P AJ39 EMIFA19 G39 EMU18 AA4 DDR3BDQS6N AL38 EMIFA20 C36 GPIO00 F29 DDR3BDQS6P AL39 EMIFA21 J36 GPIO01 B30 DDR3BDQS7N AN39 EMIFA22 H38 GPIO02 D29 DDR3BDQS7P AN38 EMIFA23 D36 GPIO03 A35 DDR3BDQS8N AE38 EMIFBE0 H34 GPIO04 B29 DDR3BDQS8P AE39 EMIFBE1 H33 GPIO05 E29 DDR3BODT0 AC33 EMIFCE0 G33 GPIO06 D30 DDR3BODT1 AD34 EMIFCE1 G32 GPIO07 C30 DDR3BRAS AD32 EMIFCE2 G34 GPIO08 A30 DDR3BRESET AC32 EMIFCE3 E36 GPIO09 G30 DDR3BRZQ0 AA31 EMIFD00 M32 GPIO10 F31 DDR3BRZQ1 P32 EMIFD01 J37 GPIO11 E30 DDR3BRZQ2 AK32 EMIFD02 L33 GPIO12 F30 DDR3BVREFSSTL AC31 EMIFD03 L34 GPIO13 A31 DDR3BWE AC37 EMIFD04 H39 GPIO14 E32 EMIFD05 J38 GPIO15 B31 EMIFD06 K37 GPIO16 A36 DVDD15 H7, H9, H11, H13, H15, H17, H19, H21, H23, J6, J8, J10, J12, J14, J16, J18, J20, J22, K7, K9, K11, K13, K15, K17, K19, K21, K23, L8, L10, L12, L14, L16, L18, L20 EMIFD07 J39 GPIO17 A32 EMIFD08 K39 GPIO18 C31 DVDD15 36 DVDD18 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-4. Terminal Functions — By Signal Name (continued) SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER GPIO19 B32 HYP1RXP0 AU8 RIORXP2 AW23 GPIO20 A33 HYP1RXP1 AV7 RIORXP3 AV22 GPIO21 D33 HYP1RXP2 AU5 RIOTXN0 AT24 GPIO22 D31 HYP1RXP3 AV4 RIOTXN1 AR23 GPIO23 B35 HYP1RXPMCLK AF3 RIOTXN2 AP22 GPIO24 B33 HYP1RXPMDAT AF4 RIOTXN3 AT21 GPIO25 E31 HYP1TXFLCLK AH3 RIOTXP0 AT25 GPIO26 A34 HYP1TXFLDAT AH2 RIOTXP1 AR24 GPIO27 D32 HYP1TXN0 AT6 RIOTXP2 AP23 GPIO28 C33 HYP1TXN1 AP5 RIOTXP3 AT22 GPIO29 C34 HYP1TXN2 AR4 RSV000 P2 GPIO30 B36 HYP1TXN3 AT3 RSV001 P1 GPIO31 B34 HYP1TXP0 AT7 RSV002 AN4 HOUT AE5 HYP1TXP1 AP6 RSV003 AM4 HYP0CLKN AT10 HYP1TXP2 AR5 RSV004 B24 HYP0CLKP AT9 HYP1TXP3 AT4 RSV005 A24 HYP0REFRES AM9 HYP1TXPMCLK AH1 RSV006 AP38 HYP0RXFLCLK AJ5 HYP1TXPMDAT AF2 RSV007 AP39 HYP0RXFLDAT AJ4 LENDIAN† F29 RSV008 AU34 HYP0RXN0 AW10 LRESETNMIEN AD4 RSV009 AT34 HYP0RXN1 AU10 LRESET AE4 RSV010 C38 HYP0RXN2 AV9 MAINPLLODSEL† E32 RSV011 D38 HYP0RXN3 AW7 MDCLK AP31 RSV012 AK5 HYP0RXP0 AW11 MDIO AR32 RSV013 F23 HYP0RXP1 AU11 NMI AD5 RSV014 E23 HYP0RXP2 AV10 PACLKSEL AN30 RSV015 E33 HYP0RXP3 AW8 PASSCLKN AV34 RSV016 F32 HYP0RXPMCLK AJ2 PASSCLKP AV33 RSV017 F26 HYP0RXPMDAT AG3 PCIECLKN AW32 RSV018 G26 HYP0TXFLCLK AJ3 PCIECLKP AW31 RSV019 AN10 HYP0TXFLDAT AG5 PCIEREFRES AM26 RSV020 AM7 HYP0TXN0 AP11 PCIERXN0 AU31 RSV021 AM23 HYP0TXN1 AR10 PCIERXN1 AV30 RSV022 AM28 HYP0TXN2 AP8 PCIERXP0 AU32 RSV023 AM25 HYP0TXN3 AR7 PCIERXP1 AV31 RSV024 AM16 HYP0TXP0 AP12 PCIETXN0 AT30 RSV025 AM14 HYP0TXP1 AR11 PCIETXN1 AR29 RSV026 AN19 HYP0TXP2 AP9 PCIETXP0 AT31 RSV027 D12 HYP0TXP3 AR8 PCIETXP1 AR30 RSV028 D13 HYP0TXPMCLK AH5 POR AK4 RSV029 F13 HYP0TXPMDAT AJ1 RESETFULL AD3 RSV030 AD35 HYP1CLKN AW5 RESETSTAT AC5 RSV031 AC34 HYP1CLKP AW4 RESET AD2 RSV032 AB32 AM21 RSV060 (66AK2H12/06 only) AV19 AV18 HYP1REFRES AM6 RIOREFRES HYP1RXFLCLK AH4 RIORXN0 AV24 RSV061 (66AK2H12/06 only) HYP1RXFLDAT AG2 RIORXN1 AU22 RSV062 (66AK2H12/06 only) AT19 AT18 HYP1RXN0 AU7 RIORXN2 AW22 RSV063 (66AK2H12/06 only) HYP1RXN1 AV6 RIORXN3 AV21 RSV064 (66AK2H12/06 only) AW20 HYP1RXN2 AU4 RIORXP0 AV25 RSV065 (66AK2H12/06 only) AW19 HYP1RXN3 AV3 RIORXP1 AU23 RSV066 (66AK2H12/06 only) AR20 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 37 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-4. Terminal Functions — By Signal Name (continued) SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER RSV067 (66AK2H12/06 only) AR19 RSV189 AR1 SPI2DIN F28 RSV068 (66AK2H12/06 only) AN16 RSV190 AT1 SPI2DOUT G28 RSV069 (66AK2H12/06 only) AM19 RSV191 AP34 SPI2SCS0 B28 RSV070 (66AK2H12/06 only) AU19 RSV192 AM30 SPI2SCS1 D28 RSV071 (66AK2H12/06 only) AU20 RSV193 AP32 SPI2SCS2 A29 RSV072 (66AK2H12/06 only) AT33 RSV194 AN32 SPI2SCS3 E25 RSV073 (66AK2H12/06 only) AR34 RSV195 AP33 SRIOSGMIICLKN AW35 RSV74 AT37 SCL0 N1 SRIOSGMIICLKP AW34 RSV75 AT35 SCL1 N4 SYSCLKN AK3 RSV76 AU36 SCL2 P4 SYSCLKOUT AK1 RSV77 AV37 SDA1 N2 SYSCLKP AL3 RSV78 AU37 SDA2 N3 TCK AE1 RSV79 AV36 SGMII0RXN AW28 TDI AG1 RSV80 AU35 SGMII0RXP AW29 TDO AF1 RSV81 AW36 SGMII0TXN AU28 TIMI0 M2 RSV099 AM11 SGMII0TXP AU29 TIMI1 M1 RSV161 AW16 SGMII1RXN AV27 TIMO0 M3 RSV162 AW17 SGMII1RXP AV28 TIMO1 M4 RSV163 AU16 SGMII1TXN AT27 TMS AE2 RSV164 AU17 SGMII1TXP AT28 TRST AD1 RSV165 AV15 SGMII2RXN AU25 TSCOMPOUT AB1 RSV166 AV16 SGMII2RXP AU26 TSPUSHEVT0 AC2 RSV167 AW13 SGMII2TXN AR26 TSPUSHEVT1 AC1 RSV168 AW14 SGMII2TXP AR27 TSREFCLKN AL1 RSV169 AU13 SGMII3RXN AW25 TSREFCLKP AM1 RSV171 AV12 SGMII3RXP AW26 TSRXCLKOUT0N AP1 RSV170 AU14 SGMII3TXN AP25 TSRXCLKOUT0P AN1 RSV172 AV13 SGMII3TXP AP26 TSRXCLKOUT1N AP3 RSV173 AP17 SGMIIREFRES AM24 TSRXCLKOUT1P AN3 RSV174 AP18 SPI0CLK B26 TSSYNCEVT AC3 RSV175 AR16 SPI0DIN A26 UART0CTS L1 RSV176 AR17 SPI0DOUT A27 UART0RTS L4 RSV177 AT15 SPI0SCS0 F25 UART0RXD K4 RSV178 AT16 SPI0SCS1 C25 UART0TXD K2 RSV179 AP14 SPI0SCS2 E26 UART1CTS K1 RSV180 AP15 SPI0SCS3 D26 UART1RTS M5 RSV181 AR13 SPI1CLK C28 UART1RXD L2 RSV182 AR14 SPI1DIN F27 UART1TXD K3 RSV183 AT12 SPI1DOUT A28 USBCLKM V2 RSV184 AT13 SPI1SCS0 B27 USBCLKP W2 RSV185 AM15 SPI1SCS1 C27 USBDM T2 RSV186 AR2 SPI1SCS2 D27 USBDP U2 RSV187 AP2 SPI1SCS3 E27 USBDRVVBUS L3 RSV188 AC4 SPI2CLK D25 USBID0 R1 38 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-4. Terminal Functions — By Signal Name (continued) SIGNAL NAME BALL NUMBER USBRESREF AA1 USBRX0M Y1 USBRX0P W1 USBTX0M V1 USBTX0P U1 USBVBUS T1 SIGNAL NAME BALL NUMBER VSS V14, V16, V18, V20, V22, V24, V26, V28, V30, V33, V37, W5, W7, W9, W11, W13, W15, W17, W19, W21, W23, W25, W27, W29, W31, W35, Y2, Y6, Y8, Y10 SIGNAL NAME BALL NUMBER VDDAHV AK11, AK13, AK15, AK17, AK19, AK21, AK23, AK25, AL10, AL12, AL14, AL16, AL18, AL20, AL22, AL24 VSS Y12, Y14, Y16, Y18, Y20, Y22, Y24, Y26, Y30, Y33, Y37, AA5, AA7, AA9, AA11, AA13, AA15, AA17, AA19, AA21, AA23, AA25, AA27, AA29, AA35, AB6, AB8 VDDALV AF13, AF15, AF17, AF19, AF21, AF23, AG12, AG14, AG16, AG18, AG20, AG22, AH11, AH13, AH15, AH17, AH19, AH21, AH23, AH25, AJ12, AJ14, AJ16, AJ18, AJ20, AJ22, AJ24 VSS AB10, AB12, AB14, AB16, AB18, AB20, AB22, AB24, AB26, AB30, AB33, AB36, AB37, AC7, AC9, AC11, AC13, AC15, AC17, AC19, AC21, AC23, AC25, AC27 VDDUSB AB13 VNWA1 AG24 VSS AT23, AT26, AT29, AT32, AT36, AU1, AU2, AU3, AU6, AU9, AU12, AU15, AU18, AU21, AU24, AU27, AU30, AU33, AU39, AV1, AV2, AV5, AV8, AV11 VSS AV14, AV17, AV20, AV23, AV26, AV29 , AV32, AV35, AV38, AV39, AW2, AW3, AW6, AW9, AW12, AW15, AW18, AW21, AW24, AW27, AW30, AW33, AW37, AW38 XFICLKN (66AK2H14 only) AU20 XFICLKP (66AK2H14 only) AU19 XFIMDCLK (66AK2H14 only) AR34 XFIMDIO (66AK2H14 only) AT33 XFIREFRES0 (66AK2H14 only) AN16 XFIREFRES1 (66AK2H14 only) AM19 XFIRXN0 (66AK2H14 only) AV19 AL31, AL35, AM3, AM8, AM10, AM12, AM13, AM17, AM18, AM20, AM22, AM32, AM33, AM37, AN2, AN5, AN6, AN7, AN8, AN9, AN11, AN12, AN13, AN14 XFIRXN1 (66AK2H14 only) AW20 XFIRXP0 (66AK2H14 only) AV18 AN15, AN17, AN18, AN20, AN21, AN22, AN23, AN24, AN25, AN26, AN27, AN28, AN29, AN31, AN35, AP4, AP7, AP10, AP13, AP16, AP19, AP20, AP21, AP24 XFIRXP1 (66AK2H14 only) AW19 XFITXN0 (66AK2H14 only) AT19 XFITXN1 (66AK2H14 only) AR20 XFITXP0 (66AK2H14 only) AT18 XFITXP1 (66AK2H14 only) AR19 VCL AP36 VCNTL0 AT39 VCNTL1 AR37 VCNTL2 AR36 VCNTL3 AT38 VCNTL4 AU38 VCNTL5 AR35 VD AP35 VNWA2 AD11 VNWA3 M23 VNWA4 V11 VP AA12 VPH Y13 VPP L22, M21 VPTX Y11 VSS VSS A2, A3, A37, A38, B1, B2, B38, B39, C1, C4, C6, C8, C10, C12, C14, C16, C18, C20, C22, C24, C26, C29, C32, C39, D34, D37, E3, E5, E7, E9, E11, E13, E15, E17, E19 AG9, AG11, AG13, AG15, AG17, AG19, AG21, AG23, AG25, AG27, AG29, AG31, AG35, AH6, AH7, AH8, AH10, AH12, AH14, AH16, AH18, AH20, AH22, AH24 E21, E28, G23, G25, G27, G29, G31, G35, H4, H6, H8, H12, H14, H18, H20, H24, H26, H28, H29, H30, H32, H37, J1, J2, J3, J4, J5, J7, J9, J11, J13, J15, J17, J19 VSS AH26, AH28, AH30, AH33, AH37, AJ6, AJ7, AJ9, AJ11, AJ13, AJ15, AJ17, AJ19, AJ21, AJ23, AJ25, AJ27, AJ29, AJ31, AJ32, AJ35, AK2, AK6, AK8, AK10 VSS AK12, AK14, AK16, AK18, AK20, AK22, AK24, AK26, AK28, AK30, AK33, AK37, AL5, AL7, AL9, AL11, AL13, AL15, AL17, AL19, AL21, AL23, AL25, AL27, AL29 VSS VSS VSS VSS VSS VSS VSS J21, J23, J24, J25, J27, J29, J31, J33, K5, K6, K8, K10, K12, K14, K16, K18, K20, K22, K24, K26, K28, K30, K32, K35, L5, L7, L9, L11, L13, L15, L17, L19, L21, L23 VSS L25, L27, L29, L31, L37, M6, M8, M10, M12, M14, M16, M22, M24, M26, M28, M30, M33, N5, N7, N9, N11, N13, N15, N17, N19, N21, N23, N25, N27, N29 N31, N35, P5, P6, P8, P10, P12, P14, P16, P18, P20, P22, P24, P26, P28, P30, P33, P37, R2, R5, R7, R9, R11, R13, R15, R17, R19, R21, R23, R25, R27, R29, R31, R35 T6, T8, T10, T12, T14, T16, T18, T20, T22, T24, T26, T28, T30, T33, T37, U7, U9, U11, U13, U15, U17, U19, U21, U23, U25, U27, U29, U31, U35, V3, V6, V8, V10, V12 VSS VSS AC29, AC35, AD6, AD8, AD10, AD12, AD14, AD16, AD18, AD20, AD22, AD24, AD26, AD30, AD33, AD37, AE3, AE7, AE9, AE11, AE13, AE15, AE17, AE19 AE21, AE23, AE25, AE27, AE29, AE31, AE35, AF6, AF8, AF10, AF12, AF14, AF16, AF18, AF20, AF22, AF24, AF26, AF28, AF30, AF33, AF37, AG4, AG7 AP27, AP28, AP29, AP30, AP37, AR3, AR6, AR9, AR12, AR15, AR18, AR21, AR22, AR25, AR28, AR31, AR33, AT2, AT5, AT8, AT11, AT14, AT17, AT20 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 39 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME A1 (nopin) B6 DDR3AD23 C10 VSS A2 VSS B7 DDR3ADQS3P C11 DDR3ABA1 A3 VSS B8 DDR3AD28 C12 VSS A4 DDR3AD11 B9 DDR3AA08 C13 DDR3ACAS A5 DDR3ADQS2P B10 DDR3AA14 C14 VSS A6 DDR3ADQM2 B11 DDR3ABA0 C15 DDR3ACB01 A7 DDR3ADQS3N B12 DDR3ACLKOUTN0 C16 VSS A8 DDR3AD27 B13 DDR3ACLKOUTN1 C17 DDR3ADQM4 A9 DDR3AA11 B14 DDR3ARESET C18 VSS A10 DDR3AA13 B15 DDR3ADQS8P C19 DDR3AD40 A11 DDR3ACKE1 B16 DDR3ACB02 C20 VSS A12 DDR3ACLKOUTP0 B17 DDR3ADQS4N C21 DDR3AD52 A13 DDR3ACLKOUTP1 B18 DDR3AD45 C22 VSS A14 DDR3ARAS B19 DDR3ADQS5P C23 DDR3AD56 A15 DDR3ADQS8N B20 DDR3AD49 C24 VSS A16 DDR3ACB00 B21 DDR3ADQS6N C25 SPI0SCS1 A17 DDR3ADQS4P B22 DDR3AD61 C26 VSS A18 DDR3ADQM5 B23 DDR3ADQS7N C27 SPI1SCS1 A19 DDR3ADQS5N B24 RSV004 C28 SPI1CLK A20 DDR3AD48 B25 DDR3ACLKP C29 VSS A21 DDR3ADQS6P B26 SPI0CLK C30 GPIO07 A22 DDR3ADQM7 B27 SPI1SCS0 C30 BOOTMODE06† A23 DDR3ADQS7P B28 SPI2SCS0 C31 GPIO18 A24 RSV005 B29 GPIO04 C31 EMU20† A25 DDR3ACLKN B29 BOOTMODE03† C32 VSS A26 SPI0DIN B30 GPIO01 C33 GPIO28 A27 SPI0DOUT B30 BOOTMODE00† C33 EMU30† A28 SPI1DOUT B31 GPIO15 C34 GPIO29 A29 SPI2SCS2 B31 BOOTMODE_RSVD† C34 EMU31† A30 GPIO08 B32 GPIO19 C35 EMIFA08 A30 BOOTMODE07† B32 EMU21† C36 EMIFA20 A31 GPIO13 B33 GPIO24 C37 ARMCLKP A31 BOOTMODE12† B33 EMU26† C38 RSV010 A32 GPIO17 B34 GPIO31 C39 VSS A32 EMU19† B34 EMU33† D1 DDR3ADQS0N A33 GPIO20 B35 GPIO23 D2 DDR3AD07 A33 EMU22† B35 EMU25† D3 DDR3AD14 A34 GPIO26 B36 GPIO30 D4 DDR3AD15 A34 EMU28† B36 EMU32† D5 DDR3AD18 A35 GPIO03 B37 ARMCLKN D6 DDR3AD21 A35 BOOTMODE02† B38 VSS D7 DDR3AD31 A36 GPIO16 B39 VSS D8 DDR3AA09 A36 DDR3A_REMAP_EN† C1 VSS D9 DDR3AA07 A37 VSS C2 DDR3ADQM0 D10 DDR3AA15 A38 VSS C3 DDR3ADQS1N D11 DDR3ACE0 A39 (nopin) C4 VSS D12 RSV027 B1 VSS C5 DDR3AD22 D13 RSV028 B2 VSS C6 VSS D14 DDR3ACB06 B3 DDR3ADQS1P C7 DDR3AD24 D15 DDR3ACB04 B4 DDR3AD12 C8 VSS D16 DDR3AD36 B5 DDR3ADQS2N C9 DDR3AA06 D17 DDR3AD37 40 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME D18 DDR3AD46 E25 SPI2SCS3 F31 BOOTMODE09† D19 DDR3AD41 E26 SPI0SCS2 F32 RSV016 D20 DDR3AD50 E27 SPI1SCS3 F33 EMIFRNW D21 DDR3ADQM6 E28 VSS F34 EMIFA00 D22 DDR3AD63 E29 GPIO05 F35 EMIFA17 D23 DDR3AD58 E29 BOOTMODE04† F36 EMIFWE D24 CORESEL2 E30 GPIO11 F37 EMIFA01 D25 SPI2CLK E30 BOOTMODE10† F38 EMIFA10 D26 SPI0SCS3 E31 GPIO25 F39 EMIFA15 D27 SPI1SCS2 E31 EMU27† G1 DDR3AD00 D28 SPI2SCS1 E32 GPIO14 G2 DDR3AD03 D29 GPIO02 E32 MAINPLLODSEL† G3 DDR3AD10 D29 BOOTMODE01† E33 RSV015 G4 DDR3AD16 D30 GPIO06 E34 EMIFA04 G5 DDR3AD20 D30 BOOTMODE05† E35 EMIFA13 G6 DDR3AD29 D31 GPIO22 E36 EMIFCE3 G7 DDR3AD30 D31 EMU24† E37 EMIFOE G8 DDR3AA02 D32 GPIO27 E38 EMIFWAIT0 G9 DDR3AA01 D32 EMU29† E39 EMIFA03 G10 DDR3AA03 D33 GPIO21 F1 DDR3AD02 G11 DDR3ABA2 D33 EMU23† F2 DDR3AD06 G12 DDR3ACKE0 D34 VSS F3 DDR3ADQM1 G13 DDR3AODT1 D35 EMIFA11 F4 DDR3AD09 G14 DDR3AVREFSSTL D36 EMIFA23 F5 DDR3AD19 G15 DDR3ACB07 D37 VSS F6 DDR3AD26 G16 DDR3AD33 D38 RSV011 F7 DDR3AD25 G17 DDR3AD35 D39 EMIFWAIT1 F8 DDR3AA05 G18 DDR3AD42 E1 DDR3ADQS0P F9 DDR3AA04 G19 DDR3AD44 E2 DDR3AD05 F10 DDR3AA10 G20 DDR3AD51 E3 VSS F11 DDR3ACE1 G21 DDR3AD55 E4 DDR3AD08 F12 DDR3AWE G22 DDR3AD57 E5 VSS F13 RSV029 G23 VSS E6 DDR3ADQM3 F14 DDR3ACB05 G24 CORESEL3 E7 VSS F15 DDR3ACB03 G24 ARMAVSSHARED† E8 DDR3AA00 F16 DDR3AD34 G25 VSS E9 VSS F17 DDR3AD38 G26 RSV018 E10 DDR3AA12 F18 DDR3AD47 G27 VSS E11 VSS F19 DDR3AD43 G28 SPI2DOUT E12 DDR3AODT0 F20 DDR3AD54 G29 VSS E13 VSS F21 DDR3AD62 G30 GPIO09 E14 DDR3ADQM8 F22 DDR3AD59 G30 BOOTMODE08† E15 VSS F23 RSV013 G31 VSS E16 DDR3AD32 F24 CORESEL0 G32 EMIFCE1 E17 VSS F25 SPI0SCS0 G33 EMIFCE0 E18 DDR3AD39 F26 RSV017 G34 EMIFCE2 E19 VSS F27 SPI1DIN G35 VSS E20 DDR3AD53 F28 SPI2DIN G36 EMIFA02 E21 VSS F29 GPIO00 G37 EMIFA09 E22 DDR3AD60 F30 GPIO12 G38 EMIFA14 E23 RSV014 F30 BOOTMODE11† G39 EMIFA19 E24 CORESEL1 F31 GPIO10 H1 DDR3AD04 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 41 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME H2 DDR3AD01 J13 VSS K24 VSS H3 DDR3AD13 J14 DVDD15 K25 DVDD18 H4 VSS J15 VSS K26 VSS H5 DDR3AD17 J16 DVDD15 K27 DVDD18 H6 VSS J17 VSS K28 VSS H7 DVDD15 J18 DVDD15 K29 CVDD H8 VSS J19 VSS K30 VSS H9 DVDD15 J20 DVDD15 K31 DVDD18 H10 DDR3ARZQ1 J21 VSS K32 VSS H11 DVDD15 J22 DVDD15 K33 EMIFA07 H12 VSS J23 VSS K34 EMIFA16 H13 DVDD15 J24 VSS K35 VSS H14 VSS J25 VSS K36 EMIFD10 H15 DVDD15 J26 DVDD18 K37 EMIFD06 H16 DDR3ARZQ0 J27 VSS K38 EMIFD09 H17 DVDD15 J28 DVDD18 K39 EMIFD08 H18 VSS J29 VSS L1 UART0CTS H19 DVDD15 J30 CVDD L2 UART1RXD H20 VSS J31 VSS L3 USBDRVVBUS H21 DVDD15 J32 DVDD18 L4 UART0RTS H22 DDR3ARZQ2 J33 VSS L5 VSS H23 DVDD15 J34 EMIFA05 L6 CVDD H24 VSS J35 EMIFA18 L7 VSS H25 DVDD18 J36 EMIFA21 L8 DVDD15 H26 VSS J37 EMIFD01 L9 VSS H27 DVDD18 J38 EMIFD05 L10 DVDD15 H28 VSS J39 EMIFD07 L11 VSS H29 VSS K1 UART1CTS L12 DVDD15 H30 VSS K2 UART0TXD L13 VSS H31 CVDD K3 UART1TXD L14 DVDD15 H32 VSS K4 UART0RXD L15 VSS H33 EMIFBE1 K5 VSS L16 DVDD15 H34 EMIFBE0 K6 VSS L17 VSS H35 EMIFA06 K7 DVDD15 L18 DVDD15 H36 EMIFA12 K8 VSS L19 VSS H37 VSS K9 DVDD15 L20 DVDD15 H38 EMIFA22 K10 VSS L21 VSS H39 EMIFD04 K11 DVDD15 L22 VPP J1 VSS K12 VSS L23 VSS J2 VSS K13 DVDD15 L24 DVDD18 J3 VSS K14 VSS L25 VSS J4 VSS K15 DVDD15 L26 DVDD18 J5 VSS K16 VSS L27 VSS J6 DVDD15 K17 DVDD15 L28 CVDD J7 VSS K18 VSS L29 VSS J8 DVDD15 K19 DVDD15 L30 DVDD18 J9 VSS K20 VSS L31 VSS J10 DVDD15 K21 DVDD15 L32 DVDD15 J11 VSS K22 VSS L33 EMIFD02 J12 DVDD15 K23 DVDD15 L34 EMIFD03 42 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME L35 EMIFD12 N6 CVDD P18 VSS L36 EMIFD11 N7 VSS P19 CVDD L37 VSS N8 CVDD P20 VSS L38 DDR3BD00 N9 VSS P21 CVDD L39 DDR3BD03 N10 CVDD P22 VSS M1 TIMI1 N11 VSS P23 CVDD M1 AVSIFSEL1† N12 CVDD P24 VSS M2 TIMI0 N13 VSS P25 CVDD M2 AVSIFSEL0† N14 CVDD P26 VSS M3 TIMO0 N15 VSS P27 CVDD M4 TIMO1 N16 CVDD P28 VSS M5 UART1RTS N17 VSS P29 DVDD15 M6 VSS N18 CVDD P30 VSS M7 CVDD N19 VSS P31 DVDD15 M8 VSS N20 AVDDA2 P32 DDR3BRZQ1 M9 CVDD N21 VSS P33 VSS M10 VSS N22 CVDD P34 DDR3BDQM1 M11 DVDD15 N23 VSS P35 DDR3BD10 M12 VSS N24 CVDD P36 DDR3BD15 M13 AVDDA7 N25 VSS P37 VSS M14 VSS N26 CVDD P38 DDR3BDQS1N M15 AVDDA8 N27 VSS P39 DDR3BDQS1P M16 VSS N28 AVDDA3 R1 USBID0 M17 DVDD15 N29 VSS R2 VSS M18 AVDDA9 N30 DVDD18 R3 EMU15 M19 DVDD15 N31 VSS R4 EMU17 M20 AVDDA10 N32 DDR3BD13 R5 VSS M21 VPP N33 DDR3BD04 R6 DVDD18 M22 VSS N34 DDR3BD01 R7 VSS M23 VNWA3 N35 VSS R8 CVDD M24 VSS N36 DDR3BD06 R9 VSS M25 CVDD N37 DDR3BD05 R10 CVDD M26 VSS N38 DDR3BD07 R11 VSS M27 CVDD N39 DDR3BDQM0 R12 CVDD M28 VSS P1 RSV001 R13 VSS M29 DVDD18 P2 RSV000 R14 CVDD M30 VSS P3 SDA0 R15 VSS M31 DVDD15 P4 SCL2 R16 CVDD M32 EMIFD00 P5 VSS R17 VSS M33 VSS P6 VSS R18 CVDD M34 EMIFD13 P7 CVDD R19 VSS M35 EMIFD15 P8 VSS R20 CVDD M36 EMIFD14 P9 CVDD R21 VSS M37 DDR3BD02 P10 VSS R22 CVDDT1 M38 DDR3BDQS0P P11 AVDDA6 R23 VSS M39 DDR3BDQS0N P12 VSS R24 CVDD N1 SCL0 P13 CVDD R25 VSS N2 SDA1 P14 VSS R26 CVDD N3 SDA2 P15 CVDD R27 VSS N4 SCL1 P16 VSS R28 DVDD15 N5 VSS P17 CVDD R29 VSS Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 43 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME R30 DVDD15 U3 EMU08 V15 CVDD R31 VSS U4 EMU07 V16 VSS R32 DDR3BD09 U5 EMU12 V17 CVDD1 R33 DDR3BD14 U6 DVDD18 V18 VSS R34 DDR3BD17 U7 VSS V19 CVDD R35 VSS U8 CVDD V20 VSS R36 DDR3BD20 U9 VSS V21 CVDD1 R37 DDR3BD19 U10 CVDD V22 VSS R38 DDR3BD12 U11 VSS V23 CVDD R39 DDR3BD11 U12 CVDD V24 VSS T1 USBVBUS U13 VSS V25 CVDD T2 USBDM U14 CVDD1 V26 VSS T3 EMU09 U15 VSS V27 CVDD T4 EMU13 U16 CVDD1 V28 VSS T5 EMU16 U17 VSS V29 DVDD15 T6 VSS U18 CVDD V30 VSS T7 DVDD18 U19 VSS V31 DVDD15 T8 VSS U20 CVDD1 V32 DDR3BD30 T9 CVDD U21 VSS V33 VSS T10 VSS U22 CVDDT1 V34 DDR3BA05 T11 CVDD U23 VSS V35 DDR3BD24 T12 VSS U24 CVDD V36 DDR3BD31 T13 CVDD1 U25 VSS V37 VSS T14 VSS U26 CVDD V38 DDR3BDQS3N T15 CVDD U27 VSS V39 DDR3BDQS3P T16 VSS U28 DVDD15 W1 USBRX0P T17 CVDD U29 VSS W2 USBCLKP T18 VSS U30 DVDD15 W3 EMU04 T19 CVDD U31 VSS W4 EMU05 T20 VSS U32 DDR3BDQM3 W5 VSS T21 CVDD1 U33 DDR3BD29 W6 DVDD18 T22 VSS U34 DDR3BD26 W7 VSS T23 CVDD U35 VSS W8 CVDD T24 VSS U36 DDR3BD25 W9 VSS T25 CVDD U37 DDR3BD21 W10 CVDD T26 VSS U38 DDR3BD23 W11 VSS T27 CVDD U39 DDR3BDQM2 W12 CVDD T28 VSS V1 USBTX0M W13 VSS T29 DVDD15 V2 USBCLKM W14 CVDD T30 VSS V3 VSS W15 VSS T31 DVDD15 V4 EMU06 W16 CVDD1 T32 DDR3BD08 V5 DVDD18 W17 VSS T33 VSS V6 VSS W18 CVDD T34 DDR3BD16 V7 DVDD18 W19 VSS T35 DDR3BD18 V8 VSS W20 CVDD T36 DDR3BD22 V9 CVDD W21 VSS T37 VSS V10 VSS W22 CVDDT1 T38 DDR3BDQS2N V11 VNWA4 W23 VSS T39 DDR3BDQS2P V12 VSS W24 CVDD U1 USBTX0P V13 CVDD1 W25 VSS U2 USBDP V14 VSS W26 CVDD 44 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME W27 VSS Y39 DDR3BA13 AB12 VSS W28 DVDD15 AA1 USBRESREF AB13 VDDUSB W29 VSS AA2 EMU00 AB14 VSS W30 DVDD15 AA3 EMU11 AB15 CVDD W31 VSS AA4 EMU18 AB16 VSS W32 DDR3BA02 AA5 VSS AB17 CVDD W33 DDR3BA01 AA6 DVDD18 AB18 VSS W34 DDR3BA04 AA7 VSS AB19 CVDD W35 VSS AA8 CVDD AB20 VSS W36 DDR3BA06 AA9 VSS AB21 CVDD W37 DDR3BA07 AA10 CVDD AB22 VSS W38 DDR3BD27 AA11 VSS AB23 CVDD W39 DDR3BD28 AA12 VP AB24 VSS Y1 USBRX0M AA13 VSS AB25 CVDD Y2 VSS AA14 DVDD33 AB26 VSS Y3 EMU02 AA15 VSS AB27 CVDD Y4 EMU03 AA16 CVDD AB28 AVDDA12 Y5 DVDD18 AA17 VSS AB29 DVDD15 Y6 VSS AA18 CVDD AB30 VSS Y7 DVDD18 AA19 VSS AB31 DVDD15 Y8 VSS AA20 CVDD AB32 RSV032 Y9 CVDD AA21 VSS AB33 VSS Y10 VSS AA22 CVDD AB34 DDR3BCE0 Y11 VPTX AA23 VSS AB35 DDR3BBA2 Y12 VSS AA24 CVDD AB36 VSS Y13 VPH AA25 VSS AB37 VSS Y14 VSS AA26 CVDD AB38 DDR3BCKE1 Y15 CVDD AA27 VSS AB39 DDR3BCKE0 Y16 VSS AA28 DVDD15 AC1 TSPUSHEVT1 Y17 CVDD AA29 VSS AC2 TSPUSHEVT0 Y18 VSS AA30 DVDD15 AC3 TSSYNCEVT Y19 CVDD AA31 DDR3BRZQ0 AC4 RSV188 Y20 VSS AA32 DDR3BA00 AC5 RESETSTAT Y21 CVDD AA33 DDR3BA08 AC6 DVDD18 Y22 VSS AA34 DDR3BBA1 AC7 VSS Y23 CVDD AA35 VSS AC8 CVDD Y24 VSS AA36 DDR3BCE1 AC9 VSS Y25 CVDD AA37 DDR3BBA0 AC10 CVDD Y26 VSS AA38 DDR3BA14 AC11 VSS Y27 CVDD AA39 DDR3BA11 AC12 CVDD Y28 AVDDA11 AB1 TSCOMPOUT AC13 VSS Y29 DVDD15 AB2 EMU01 AC14 CVDD Y30 VSS AB3 EMU14 AC15 VSS Y31 DVDD15 AB4 EMU10 AC16 CVDD Y32 DDR3BA09 AB5 DVDD18 AC17 VSS Y33 VSS AB6 VSS AC18 CVDD1 Y34 DDR3BA03 AB7 DVDD18 AC19 VSS Y35 DDR3BA12 AB8 VSS AC20 CVDD Y36 DDR3BA15 AB9 CVDD AC21 VSS Y37 VSS AB10 VSS AC22 CVDD Y38 DDR3BA10 AB11 CVDD AC23 VSS Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 45 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME AC24 CVDD AD36 DDR3BCB06 AF9 CVDD AC25 VSS AD37 VSS AF10 VSS AC26 CVDD AD38 DDR3BCLKOUTP0 AF11 AVDDA1 AC27 VSS AD39 DDR3BCLKOUTN0 AF12 VSS AC28 AVDDA13 AE1 TCK AF13 VDDALV AC29 VSS AE2 TMS AF14 VSS AC30 DVDD15 AE3 VSS AF15 VDDALV AC31 DDR3BVREFSSTL AE4 LRESET AF16 VSS AC32 DDR3BRESET AE5 HOUT AF17 VDDALV AC33 DDR3BODT0 AE6 DVDD18 AF18 VSS AC34 RSV031 AE7 VSS AF19 VDDALV AC35 VSS AE8 CVDD AF20 VSS AC36 DDR3BCAS AE9 VSS AF21 VDDALV AC37 DDR3BWE AE10 CVDD AF22 VSS AC38 DDR3BCLKOUTN1 AE11 VSS AF23 VDDALV AC39 DDR3BCLKOUTP1 AE12 CVDD AF24 VSS AD1 TRST AE13 VSS AF25 CVDD AD2 RESET AE14 CVDD AF26 VSS AD3 RESETFULL AE15 VSS AF27 CVDD AD4 LRESETNMIEN AE16 CVDD AF28 VSS AD5 NMI AE17 VSS AF29 DVDD15 AD6 VSS AE18 CVDD AF30 VSS AD7 DVDD18 AE19 VSS AF31 DVDD15 AD8 VSS AE20 CVDD AF32 DDR3BCB00 AD9 CVDD AE21 VSS AF33 VSS AD10 VSS AE22 CVDD AF34 DDR3BCB01 AD11 VNWA2 AE23 VSS AF35 DDR3BCB03 AD12 VSS AE24 CVDD AF36 DDR3BD33 AD13 CVDD AE25 VSS AF37 VSS AD14 VSS AE26 CVDD AF38 DDR3BDQS4P AD15 CVDD AE27 VSS AF39 DDR3BDQS4N AD16 VSS AE28 AVDDA15 AG1 TDI AD17 CVDD1 AE29 VSS AG2 HYP1RXFLDAT AD18 VSS AE30 DVDD15 AG3 HYP0RXPMDAT AD19 CVDD1 AE31 VSS AG4 VSS AD20 VSS AE32 DDR3BCB02 AG5 HYP0TXFLDAT AD21 CVDD AE33 DDR3BCB04 AG6 DVDD18 AD22 VSS AE34 DDR3BCB07 AG7 VSS AD23 CVDD AE35 VSS AG8 CVDD AD24 VSS AE36 DDR3BCB05 AG9 VSS AD25 CVDD AE37 DDR3BDQM8 AG10 CVDD AD26 VSS AE38 DDR3BDQS8N AG11 VSS AD27 CVDD AE39 DDR3BDQS8P AG12 VDDALV AD28 AVDDA14 AF1 TDO AG13 VSS AD29 DVDD15 AF2 HYP1TXPMDAT AG14 VDDALV AD30 VSS AF3 HYP1RXPMCLK AG15 VSS AD31 DVDD15 AF4 HYP1RXPMDAT AG16 VDDALV AD32 DDR3BRAS AF5 BOOTCOMPLETE AG17 VSS AD33 VSS AF6 VSS AG18 VDDALV AD34 DDR3BODT1 AF7 DVDD18 AG19 VSS AD35 RSV030 AF8 VSS AG20 VDDALV 46 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME AG21 VSS AH33 VSS AK6 VSS AG22 VDDALV AH34 DDR3BD37 AK7 CVDD AG23 VSS AH35 DDR3BD38 AK8 VSS AG24 VNWA1 AH36 DDR3BD42 AK9 CVDD AG25 VSS AH37 VSS AK10 VSS AG26 AVDDA5 AH38 DDR3BD46 AK11 VDDAHV AG27 VSS AH39 DDR3BD45 AK12 VSS AG28 CVDD AJ1 HYP0TXPMDAT AK13 VDDAHV AG29 VSS AJ2 HYP0RXPMCLK AK14 VSS AG30 DVDD15 AJ3 HYP0TXFLCLK AK15 VDDAHV AG31 VSS AJ4 HYP0RXFLDAT AK16 VSS AG32 DDR3BD39 AJ5 HYP0RXFLCLK AK17 VDDAHV AG33 DDR3BDQM4 AJ6 VSS AK18 VSS AG34 DDR3BD35 AJ7 VSS AK19 VDDAHV AG35 VSS AJ8 CVDD AK20 VSS AG36 DDR3BD36 AJ9 VSS AK21 VDDAHV AG37 DDR3BD32 AJ10 CVDD AK22 VSS AG38 DDR3BD34 AJ11 VSS AK23 VDDAHV AG39 DDR3BDQM5 AJ12 VDDALV AK24 VSS AH1 HYP1TXPMCLK AJ13 VSS AK25 VDDAHV AH2 HYP1TXFLDAT AJ14 VDDALV AK26 VSS AH3 HYP1TXFLCLK AJ15 VSS AK27 DVDD18 AH4 HYP1RXFLCLK AJ16 VDDALV AK28 VSS AH5 HYP0TXPMCLK AJ17 VSS AK29 CVDD AH6 VSS AJ18 VDDALV AK30 VSS AH7 VSS AJ19 VSS AK31 DVDD15 AH8 VSS AJ20 VDDALV AK32 DDR3BRZQ2 AH9 CVDD AJ21 VSS AK33 VSS AH10 VSS AJ22 VDDALV AK34 DDR3BDQM6 AH11 VDDALV AJ23 VSS AK35 DDR3BD51 AH12 VSS AJ24 VDDALV AK36 DDR3BD50 AH13 VDDALV AJ25 VSS AK37 VSS AH14 VSS AJ26 DVDD18 AK38 DDR3BD49 AH15 VDDALV AJ27 VSS AK39 DDR3BD48 AH16 VSS AJ28 CVDD AL1 TSREFCLKN AH17 VDDALV AJ29 VSS AL2 ALTCORECLKN AH18 VSS AJ30 DVDD15 AL3 SYSCLKP AH19 VDDALV AJ31 VSS AL4 CORECLKSEL AH20 VSS AJ32 VSS AL5 VSS AH21 VDDALV AJ33 DDR3BD41 AL6 CVDD AH22 VSS AJ34 DDR3BD43 AL7 VSS AH23 VDDALV AJ35 VSS AL8 CVDD AH24 VSS AJ36 DDR3BD44 AL9 VSS AH25 VDDALV AJ37 DDR3BD47 AL10 VDDAHV AH26 VSS AJ38 DDR3BDQS5N AL11 VSS AH27 CVDD AJ39 DDR3BDQS5P AL12 VDDAHV AH28 VSS AK1 SYSCLKOUT AL13 VSS AH29 AVDDA4 AK2 VSS AL14 VDDAHV AH30 VSS AK3 SYSCLKN AL15 VSS AH31 DVDD15 AK4 POR AL16 VDDAHV AH32 DDR3BD40 AK5 RSV012 AL17 VSS Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 47 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME AL18 VDDAHV AM27 DVDD18 AN36 DDR3BD57 AL19 VSS AM28 RSV022 AN37 DDR3BD63 AL20 VDDAHV AM29 DVDD18 AN38 DDR3BDQS7P AL21 VSS AM30 RSV192 AN39 DDR3BDQS7N AL22 VDDAHV AM31 CVDD AP1 TSRXCLKOUT0N AL23 VSS AM32 VSS AP2 RSV187 AL24 VDDAHV AM33 VSS AP3 TSRXCLKOUT1N AL25 VSS AM34 DDR3BD59 AP4 VSS AL26 DVDD18 AM35 DDR3BD60 AP5 HYP1TXN1 AL27 VSS AM36 DDR3BD62 AP6 HYP1TXP1 AL28 DVDD18 AM37 VSS AP7 VSS AL29 VSS AM38 DDR3BD61 AP8 HYP0TXN2 AL30 CVDD AM39 DDR3BDQM7 AP9 HYP0TXP2 AL31 VSS AN1 TSRXCLKOUT0P AP10 VSS AL32 DVDD15 AN2 VSS AP11 HYP0TXN0 AL33 DDR3BD55 AN3 TSRXCLKOUT1P AP12 HYP0TXP0 AL34 DDR3BD52 AN4 RSV002 AP13 VSS AL35 VSS AN5 VSS AP14 RSV179 AL36 DDR3BD53 AN6 VSS AP15 RSV180 AL37 DDR3BD54 AN7 VSS AP16 VSS AL38 DDR3BDQS6N AN8 VSS AP17 RSV173 AL39 DDR3BDQS6P AN9 VSS AP18 RSV174 AM1 TSREFCLKP AN10 RSV019 AP19 VSS AM2 ALTCORECLKP AN11 VSS AP20 VSS AM3 VSS AN12 VSS AP21 VSS AM4 RSV003 AN13 VSS AP22 RIOTXN2 AM5 CVDD AN14 VSS AP23 RIOTXP2 AM6 HYP1REFRES AN15 VSS AP24 VSS AM7 RSV020 AP25 SGMII3TXN AM8 VSS AN16 (66AK2H14 only) AP26 SGMII3TXP AM9 HYP0REFRES AP27 VSS AM10 AP28 VSS XFIREFRES0 RSV068 VSS AN16 (66AK2H12/06 only) AM11 RSV099 AN17 VSS AP29 VSS AM12 VSS AN18 VSS AP30 VSS AM13 VSS AN19 RSV026 AP31 MDCLK AM14 RSV025 AN20 VSS AP32 RSV193 AM15 RSV185 AN21 VSS AP33 RSV195 AM16 RSV024 AN22 VSS AP34 RSV191 AM17 VSS AN23 VSS AP35 VD AM18 VSS AN24 VSS AP36 VCL AN25 VSS AP37 VSS AN26 VSS AP38 RSV006 AN27 VSS AP39 RSV007 AN28 VSS AR1 RSV189 AM19 (66AK2H14 only) XFIREFRES1 AM19 (66AK2H12/06 only) RSV069 AM20 VSS AN29 VSS AR2 RSV186 AM21 RIOREFRES AN30 PACLKSEL AR3 VSS AM22 VSS AN31 VSS AR4 HYP1TXN2 AM23 RSV021 AN32 RSV194 AR5 HYP1TXP2 AM24 SGMIIREFRES AN33 DDR3BD58 AR6 VSS AM25 RSV023 AN34 DDR3BD56 AR7 HYP0TXN3 AM26 PCIEREFRES AN35 VSS AR8 HYP0TXP3 48 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME AR9 VSS AT12 RSV183 AU15 VSS AR10 HYP0TXN1 AT13 RSV184 AU16 RSV163 AR11 HYP0TXP1 AT14 VSS AU17 RSV164 AR12 VSS AT15 RSV177 AU18 VSS AR13 RSV181 AT16 RSV178 RSV070 AR14 RSV182 AT17 VSS AU19 (66AK2H12/06 only) AR15 VSS AU19 (66AK2H14 only) XFICLKP RSV175 AT18 (66AK2H14 only) XFITXP0 AR16 AR17 RSV176 AU20 (66AK2H12/06 only) RSV071 VSS AT18 (66AK2H12/06 only) RSV063 AR18 AR19 (66AK2H14 only) XFITXP1 AT19 (66AK2H14 only) XFITXN0 AU20 (66AK2H14 only) XFICLKN AR19 (66AK2H12/06 only) AT19 (66AK2H12/06 only) AU21 VSS RSV067 RSV062 AU22 RIORXN1 AT20 VSS AU23 RIORXP1 AT21 RIOTXN3 AU24 VSS AT22 RIOTXP3 AU25 SGMII2RXN AT23 VSS AU26 SGMII2RXP AR20 (66AK2H14 only) XFITXN1 AR20 (66AK2H12/06 only) RSV066 AR21 VSS AT24 RIOTXN0 AU27 VSS AR22 VSS AT25 RIOTXP0 AU28 SGMII0TXN AR23 RIOTXN1 AT26 VSS AU29 SGMII0TXP AR24 RIOTXP1 AT27 SGMII1TXN AU30 VSS AR25 VSS AT28 SGMII1TXP AU31 PCIERXN0 AR26 SGMII2TXN AT29 VSS AU32 PCIERXP0 AR27 SGMII2TXP AT30 PCIETXN0 AU33 VSS AR28 VSS AT31 PCIETXP0 AU34 RSV008 AR29 PCIETXN1 AT32 VSS AU35 RSV80 AR30 PCIETXP1 AU36 RSV76 AR31 VSS AU37 RSV78 AR32 MDIO AU38 VCNTL4 AR33 VSS AU39 VSS AR34 (66AK2H14 only) AT33 (66AK2H14 only) XFIMDIO AT33 (66AK2H12/06 only) RSV072 AT34 RSV009 AV1 VSS AT35 RSV75 AV2 VSS AT36 VSS AV3 HYP1RXN3 AT37 RSV74 AV4 HYP1RXP3 XFIMDCLK AR34 (66AK2H12/06 only) RSV073 AR35 VCNTL5 AT38 VCNTL3 AV5 VSS AR36 VCNTL2 AT39 VCNTL0 AV6 HYP1RXN1 AR37 VCNTL1 AU1 VSS AV7 HYP1RXP1 AR38 DDR3BCLKP AU2 VSS AV8 VSS AR39 DDR3BCLKN AU3 VSS AV9 HYP0RXN2 AT1 RSV190 AU4 HYP1RXN2 AV10 HYP0RXP2 AT2 VSS AU5 HYP1RXP2 AV11 VSS AT3 HYP1TXN3 AU6 VSS AV12 RSV171 AT4 HYP1TXP3 AU7 HYP1RXN0 AV13 RSV172 AT5 VSS AU8 HYP1RXP0 AV14 VSS AT6 HYP1TXN0 AU9 VSS AV15 RSV165 AT7 HYP1TXP0 AU10 HYP0RXN1 AV16 RSV166 AT8 VSS AU11 HYP0RXP1 AV17 VSS AT9 HYP0CLKP AU12 VSS AT10 HYP0CLKN AU13 RSV169 AV18 (66AK2H14 only) XFIRXP0 AT11 VSS AU14 RSV170 Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 49 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 4-5. Terminal Functions — By Ball Number (continued) BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME BALL NUMBER SIGNAL NAME AV38 VSS XFIRXN1 AV39 VSS AW20 (66AK2H14 only) AW1 (nopin) VSS AW20 (66AK2H12/06 only) RSV064 AW2 AW3 VSS AW21 VSS AW4 HYP1CLKP AW22 RIORXN2 VSS AW5 HYP1CLKN AW23 RIORXP2 AV21 RIORXN3 AW6 VSS AW24 VSS AV22 RIORXP3 AW7 HYP0RXN3 AW25 SGMII3RXN AV23 VSS AW8 HYP0RXP3 AW26 SGMII3RXP AV24 RIORXN0 AW9 VSS AW27 VSS AV25 RIORXP0 AW10 HYP0RXN0 AW28 SGMII0RXN AV26 VSS AW11 HYP0RXP0 AW29 SGMII0RXP AV27 SGMII1RXN AW12 VSS AW30 VSS AV28 SGMII1RXP AW13 RSV167 AW31 PCIECLKP AV29 VSS AW14 RSV168 AW32 PCIECLKN AV30 PCIERXN1 AW15 VSS AW33 VSS AV31 PCIERXP1 AW16 RSV161 AW34 SRIOSGMIICLKP AV32 VSS AW17 RSV162 AW35 SRIOSGMIICLKN AV33 PASSCLKP AW18 VSS AW36 RSV81 AV34 PASSCLKN AW37 VSS AV35 VSS AW19 (66AK2H14 only) AW38 VSS AV36 RSV79 AW39 (nopin) AV37 RSV77 AV18 (66AK2H12/06 only) RSV061 AV19 (66AK2H14 only) XFIRXN0 AV19 (66AK2H12/06 only) RSV060 AV20 4.4 AW19 (66AK2H12/06 only) XFIRXP1 RSV065 Pullup/Pulldown Resistors Proper board design should ensure that input pins to the device always be at a valid logic level and not floating. This may be achieved via pullup/pulldown resistors. The device features internal pullup (IPU) and internal pulldown (IPD) resistors on most pins to eliminate the need, unless otherwise noted, for external pullup/pulldown resistors. An external pullup/pulldown resistor needs to be used in the following situations: • Device Configuration Pins: If the pin is both routed out and not driven (in Hi-Z state), an external pullup/pulldown resistor must be used, even if the IPU/IPD matches the desired value/state. • Other Input Pins: If the IPU/IPD does not match the desired value/state, use an external pullup/pulldown resistor to pull the signal to the opposite rail. For the device configuration pins (listed in Table 10-29), if they are both routed out and are not driven (in Hi-Z state), it is strongly recommended that an external pullup/pulldown resistor be implemented. Although, internal pullup/pulldown resistors exist on these pins and they may match the desired configuration value, providing external connectivity can help ensure that valid logic levels are latched on these device configuration pins. In addition, applying external pullup/pulldown resistors on the device configuration pins adds convenience to the user in debugging and flexibility in switching operating modes. Tips for choosing an external pullup/pulldown resistor: • Consider the total amount of current that may pass through the pullup or pulldown resistor. Be sure to include the leakage currents of all the devices connected to the net, as well as any internal pullup or pulldown resistors. • Decide a target value for the net. For a pulldown resistor, this should be below the lowest VIL level of all inputs connected to the net. For a pullup resistor, this should be above the highest VIH level of all inputs on the net. A reasonable choice would be to target the VOL or VOH levels for the logic family of the limiting device; which, by definition, have margin to the VIL and VIH levels. 50 Terminal Configuration and Functions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com • • • • SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Select a pullup/pulldown resistor with the largest possible value that still ensures that the net will reach the target pulled value when maximum current from all devices on the net is flowing through the resistor. The current to be considered includes leakage current plus, any other internal and external pullup/pulldown resistors on the net. For bidirectional nets, there is an additional consideration that sets a lower limit on the resistance value of the external resistor. Verify that the resistance is small enough that the weakest output buffer can drive the net to the opposite logic level (including margin). Remember to include tolerances when selecting the resistor value. For pullup resistors, also remember to include tolerances on the DVDD rail. For most systems: • A 1-kΩ resistor can be used to oppose the IPU/IPD while meeting the above criteria. Users should confirm this resistor value is correct for their specific application. • A 20-kΩ resistor can be used to compliment the IPU/IPD on the device configuration pins while meeting the above criteria. Users should confirm this resistor value is correct for their specific application. For more detailed information on input current (II), and the low-level and high-level input voltages (VIL and VIH) for the 66AK2Hxx device, see Section 5.5. To determine which pins on the device include internal pullup/pulldown resistors, see Table 4-3. Terminal Configuration and Functions Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 51 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 5 Specifications 5.1 Absolute Maximum Ratings over operating case temperature range (unless otherwise noted) (1) CVDD –0.3 V to 1.3 V CVDD1 –0.3 V to 1.3 V CVDDT1 –0.3 V to 1.3 V DVDD15 –0.3 V to 1.98 V DVDD18 –0.3 V to 2.45 V DVDD33 –0.3V to 3.63 V DDR3VREFSSTL Supply voltage (2): 0.49 × DVDD15 to 0.51 × DVDD15 VDDAHV –0.3 V to 1.98 V VDDALV –0.3 V to 0.935 V VDDUSB –0.3V to 0.935 V AVDDA1, AVDDA2, AVDDA3,AVDDA4, AVDDA5 –0.3 V to 1.98 V AVDDA6, AVDDA7, AVDDA8, AVDDA9, AVDDA10, AVDDA11, AVDDA12, AVDDA13, AVDDA14, AVDDA15 –0.3 V to 1.98 V VSS Ground Input voltage (VI): (3) 0V LVCMOS (1.8 V) –0.3 V to DVDD18+0.3 V DDR3A, DDR3B –0.3 V to 1.98 V I2C –0.3 V to 2.45 V LVDS –0.3 V to DVDD18+0.3 V LJCB –0.3 V to 1.3 V SerDes Output voltage (VO): (3) –0.3 V to VDDAHV1+0.3 V LVCMOS (1.8 V) –0.3 V to DVDD18+0.3 V DDR3A, DDR3B –0.3 V to 1.98 V I2C –0.3 V to 2.45 V SerDes Operating case temperature, TC: –0.3 V to VDDAHV+0.3 V Commercial 0°C to 85°C Extended –40°C to 100°C LVCMOS (1.8 V) Overshoot/undershoot (4) 20% overshoot/undershoot for 20% of signal duty cycle DDR3A, DDR3B I2C Storage temperature, Tstg: (1) (2) (3) (4) –65°C to 150°C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to VSS. For USB High-Speed, Full-Speed, and Low -Speed modes, USB I/Os adhere to Universal Serial Bus, revision 2.0 standard. For USB Super-Speed mode, USB I/Os adhere to Universal Serial Bus, revision 3.1 specification, revision 1.0 standard. Overshoot/Undershoot percentage relative to I/O operating values - for example the maximum overshoot value for 1.8 V LVCMOS signals is DVDD18 + 0.20 × DVDD18 and maximum undershoot value would be VSS - 0.20 × DVDD18 5.2 ESD Ratings VALUE VESD (1) (2) 52 Electrostatic discharge (ESD) Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) Charged device model (CDM), per JESD22-C101 (2) ±1000 ±250 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Specifications Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 5.3 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Recommended Operating Conditions (1) (2) Initial CVDD (3) 1000-MHz device SR DSP core supply 1200-MHz device MIN NOM MAX UNIT 0.95 1.0 1.05 V SRVnom*0.95 (4) SRVnom SRVnom*1.05 SRVnom*0.95 (4) SRVnom SRVnom*1.05 V V CVDD1 DSP core supply 0.902 0.95 0.997 V CVDDT1 Cortex-A15 processor core supply 0.902 0.95 0.997 V DVDD18 1.8-V supply I/O voltage 1.71 1.8 1.89 V DDR3 1.425 1.5 1.575 DDR3L at 1.5 V 1.425 1.5 1.575 DDR3L at 1.35 V 1.283 1.35 1.45 0.49 × DVDD15 0.5 × DVDD15 0.51 × DVDD15 V DVDD15 DDR3 I/O voltage V DDR3VREFSSTL DDR3A, DDR3B reference voltage VDDAHV SerDes regulator supply 1.71 1.8 1.89 V PLL analog, DDR DLL supply 1.71 1.8 1.89 V AVDDx (5) VDDALH SerDes termination supply 0.807 0.85 0.892 V DVDD33 USB 3.135 3.3 3.465 V VDDUSB USB 0.807 0.85 0.892 V VSS Ground 0 0 0 V LVCMOS (1.8 V) VIH (6) I2C High-level input voltage DDR3A, DDR3B EMIF 0.65 × DVDD18 0.7 × DVDD18 LVCMOS (1.8 V) VIL (6) DDR3A, DDR3B EMIF Low-level input voltage 0.35 × DVDD18 -0.3 2 (1) (2) (3) (4) (5) (6) 5.4 Operating case temperature Commercial Extended VREFSSTL - 0.1 V 0.3 × DVDD18 IC TC V VREFSSTL + 0.1 0 85 –40 100 °C All differential clock inputs comply with the LVDS Electrical Specification, IEEE 1596.3-1996 and all SerDes I/Os comply with the XAUI Electrical Specification, IEEE 802.3ae-2002. All SerDes I/Os comply with the XAUI Electrical Specification, IEEE 802.3ae-2002. Users are required to program their board CVDD supply initial value to 1.0 V on the device. The initial CVDD voltage at power-on will be 1.0 V nominal and it must transition to VID set value, immediately after being presented on the VCNTL pins. This is required to maintain full power functionality and reliability targets ensured by TI. SRVnom refers to the unique SmartReflex core supply voltage that has a potential range of 0.8 V and 1.1 V which preset from the factory for each individual device. Your device may never be programmed to operate at the upper range but has been designed accordingly should it be determined to be acceptable or necessary. Power supplies intended to support the variable SRV function shall be capable of providing a 0.8 V-1.1 V dynamic range using a 4- or 6-bit binary input value which as provided by the DSP SmartReflex output. Where x = 1,2,3,4... to indicate all supplies of the same kind. For USB High-Speed, Full-Speed, and Low -Speed modes, USB I/Os adhere to Universal Serial Bus, revision 2.0 standard. For USB Super-Speed mode, USB I/Os adhere to Universal Serial Bus, revision 3.1 specification, revision 1.0 standard. Power Consumption Summary For information on the device power consumption, see the power estimation spreadsheet provided in 66AK2H14 Power Consumption Model, 66AK2H12 Power Consumption Model, and 66AK2H06 Power Consumption Model. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Specifications 53 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 5.5 www.ti.com Electrical Characteristics over recommended ranges of supply voltage and operating case temperature (unless otherwise noted) TEST CONDITIONS (1) PARAMETER LVCMOS (1.8 V) (2) VOH High-level output voltage MIN TYP MAX UNIT DVDD18 – 0.45 IO = IOH DDR3A, DDR3B V DVDD15 – 0.4 I2C (3) LVCMOS (1.8 V) VOL (2) Low-level output voltage IO = IOL 0.45 DDR3A, DDR3B I2C 0.4 IO = 3 mA, pulled up to 1.8 V No IPD/IPU LVCMOS (1.8 V) II (4) Input current [DC] Internal pulldown I2C High-level output current [DC] IOH Low-level output current [DC] IOL –10 Internal pullup 0.1 × DVDD18 V < VI < 0.9 × DVDD18 V Off-state output current [DC] 100 170 –170 –100 –50 –10 –6 DDR3A, DDR3B –8 (5) (6) 5.6 LVCMOS (1.8 V) 6 DDR3A, DDR3B 8 2 54 mA 3 LVCMOS (1.8 V) –10 10 DDR3A, DDR3B –10 10 –10 10 2 µA Thermal Resistance Characteristics for PBGA Package [AAW] °C/W (1) NO. (2) mA I2C (5) For test conditions shown as MIN, MAX, or TYP, use the appropriate value specified in the recommended operating conditions table. For USB High-Speed, Full-Speed, and Low-Speed modes, USB I/Os adhere to Universal Serial Bus, revision 2.0 standard. For USB Super-Speed mode, USB I/Os adhere to Universal Serial Bus, revision 3.1 specification, revision 1.0 standard. I2C uses open collector I/Os and does not have a VOH minimum. II applies to input-only pins and bidirectional pins. For input-only pins, II indicates the input leakage current. For bidirectional pins, II includes input leakage current and off-state (Hi-Z) output leakage current. I2C uses open collector I/Os and does not have a IOH maximum. IOZ applies to output-only pins, indicating off-state (Hi-Z) output leakage current. (3) (4) (1) µA 10 LVCMOS (1.8 V) I C (1) (2) 10 50 I C IOZ (6) V 0.4 1 RΘJC Junction-to-case 0.11 2 RΘJB Junction-to-board 1.65 (2) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/JEDEC standards: • JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air) • JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages • JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages • JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements °C/W = degrees Celsius per watt. Specifications Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 5.7 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Power Supply to Peripheral I/O Mapping over recommended ranges of supply voltage and operating case temperature (unless otherwise noted) (1) (2) POWER SUPPLY I/O BUFFER TYPE ASSOCIATED PERIPHERAL SYSCLK(P|N) PLL input buffer ALTCORECLK(P|N) PLL input buffer SRIOSGMIICLK(P|N) SerDes PLL input buffer CVDD Supply core AVS voltage LJCB DDR3ACLK(P|N) PLL input buffer DDR3BCLK(P|N) PLL input buffer PASSCLK(P|N) PLL input buffer ARMCLK(P|N) PLL input buffer VDDALV LJCB SERDES low voltage PCIECLK(P|N) SerDes Clock Reference VDDAHV SerDes I/O voltage SerDes/CML DVDD15 1.35-V / 1.5-V supply I/O voltage DDR3A, DDR3B (1.35 V / 1.5 V) HYP0CLK(P|N) SerDes Clock Reference HYP1CLK(P|N) SerDes Clock Reference USBCLK(P|M) SerDes Clock Reference All DDR3A, DDR3B memory controller peripheral I/O buffer All GPIO peripheral I/O buffer All JTAG and EMU peripheral I/O buffer All TIMER peripheral I/O buffer All SPI peripheral I/O buffer DVDD18 1.8-V supply I/O voltage LVCMOS (1.8 V) All RESETs, NMI, control peripheral I/O buffer All SmartReflex peripheral I/O buffer All Hyperlink sideband peripheral I/O buffer All MDIO peripheral I/O buffer All UART peripheral I/O buffer Open-drain (1.8 V) (1) (2) All I2C peripheral I/O buffer This table does not try to describe all functions of all power supply terminals but only those whose purpose it is to power peripheral I/O buffers and clock input buffers. See Hardware Design Guide for KeyStone II Devices for more information about individual peripheral I/O. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Specifications 55 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 6 C66x CorePac The C66x CorePac consists of several components: • Level-one and level-two memories (L1P, L1D, L2) • Data Trace Formatter (DTF) • Embedded Trace Buffer (ETB) • Interrupt controller • Power-down controller • External memory controller • Extended memory controller • A dedicated local power/sleep controller (LPSC) The C66x CorePac also provides support for big and little endianness, memory protection, and bandwidth management (for resources local to the CorePac). Figure 6-1 shows a block diagram of the C66x CorePac. C66x DSP Core Interrupt and Exception Controller Instruction Fetch 16-/32-bit Instruction Dispatch Control Registers In-Circuit Emulation Instruction Decode Data Path A PLLC LPSC A Register File B Register File A31-A16 A15-A0 B31-B16 B15-B0 .M1 xx xx .M2 xx xx GPSC .L1 Data Path B .S1 .D1 .D2 .S2 .L2 Data Memory Controller (DMC) With Memory Protect/Bandwidth Mgmt L2 Cache/ SRAM 1024KB MSM SRAM 6144KB DDR3 SRAM DMA Switch Fabric External Memory Controller (EMC) Boot Controller Extended Memory Controller (XMC) Memory Controller (PMC) With Memory Protect/Bandwidth Mgmt Unified Memory Controller (UMC) 32KB L1P CFG Switch Fabric 32KB L1D Copyright © 2016, Texas Instruments Incorporated Figure 6-1. C66x CorePac Block Diagram For more detailed information on the C66x CorePac in the 66AK2Hxx device, see the TMS320C66x DSP CorePac User's Guide. 56 C66x CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 6.1 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 C66x DSP CorePac The C66x DSP CorePac extends the performance of the C64x+ and C674x CPUs through enhancements and new features. Many of the new features target increased performance for vector processing. The C64x+ and C674x DSPs support 2-way SIMD operations for 16-bit data and 4-way SIMD operations for 8bit data. On the C66x DSP, the vector processing capability is improved by extending the width of the SIMD instructions. C66x DSPs can execute instructions that operate on 128-bit vectors. The C66x CPU also supports SIMD for floating-point operations. Improved vector processing capability (each instruction can process multiple data in parallel) combined with the natural instruction level parallelism of C6000™ architecture (for example, execution of up to 8 instructions per cycle) results in a very high level of parallelism that can be exploited by DSP programmers through the use of TI's optimized C/C++ compiler. For more details on the C66x CPU and its enhancements over the C64x+ and C674x architectures, see the following documents: • TMS320C66x DSP CPU and Instruction Set Reference Guide • TMS320C66x DSP Cache User's Guide • TMS320C66x DSP CorePac User's Guide 6.2 Memory Architecture Each C66x CorePac of the 66AK2Hxx device contains a 1024KB level-2 memory (L2), a 32KB level-1 program memory (L1P), and a 32KB level-1 data memory (L1D). The device also contains a 6144KB multicore shared memory (MSM). All memory on the 66AK2Hxx has a unique location in the memory map (see Section 8). After device reset, L1P and L1D cache are configured as all cache, by default. The L1P and L1D cache can be reconfigured via software through the L1PMODE field of the L1P Configuration Register (L1PMODE) and the L1DMODE field of the L1D Configuration Register (L1DCFG) of the C66x CorePac. L1D is a two-way set-associative cache, while L1P is a direct-mapped cache. The on-chip bootloader changes the reset configuration for L1P and L1D. For more information, see the KeyStone Architecture DSP Bootloader User's Guide. For more information on the operation L1 and L2 caches, see the TMS320C66x DSP Cache User's Guide. 6.2.1 L1P Memory The L1P memory configuration for the 66AK2Hxx device is as follows: • Region 0 size is 0KB (disabled) • Region 1 size is 32KB with no wait states Figure 6-2 shows the available SRAM/cache configurations for L1P. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 C66x CorePac 57 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com L1P Mode Bits 000 001 010 Block Base Address 011 100 L1P Memory 00E0 0000h 1/2 SRAM All SRAM 7/8 SRAM 16KB 3/4 SRAM Direct Mapped Cache 00E0 4000h 8KB DM Cache Direct Mapped Cache Direct Mapped Cache 00E0 6000h 4KB 00E0 7000h 4KB 00E0 8000h Figure 6-2. L1P Memory Configurations 6.2.2 L1D Memory The L1D memory configuration for the 66AK2Hxx device is as follows: • Region 0 size is 0KB (disabled) • Region 1 size is 32KB with no wait states Figure 6-3 shows the available SRAM/cache configurations for L1D. L1D Mode Bits 000 001 010 011 100 L1D Memory Block Base Address 00F0 0000h 1/2 SRAM All SRAM 7/8 SRAM 16KB 3/4 SRAM 2-Way Cache 00F0 4000h 8KB 2-Way Cache 2-Way Cache 2-Way Cache 00F0 6000h 4KB 00F0 7000h 4KB 00F0 8000h Figure 6-3. L1D Memory Configurations 6.2.3 L2 Memory The L2 memory configuration for the 66AK2Hxx device is as follows: • Total memory size is 8192KB 58 C66x CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com • • SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Each CorePac contains 1024KB of memory Local starting address for each CorePac is 0080 0000h L2 memory can be configured as all SRAM, all 4-way set-associative cache, or a mix of the two. The amount of L2 memory that is configured as cache is controlled through the L2MODE field of the L2 Configuration Register (L2CFG) of the C66x CorePac. Figure 6-4 shows the available SRAM/cache configurations for L2. By default, L2 is configured as all SRAM after device reset. L2 Mode Bits 000 001 010 011 100 101 110 L2 Memory Block Base Address 0080 0000h 1/2 SRAM 512KB 3/4 SRAM ALL SRAM 31/32 SRAM 15/16 SRAM 7/8 SRAM 4-Way Cache 0088 0000h 256KB 4-Way Cache 008C 0000h 128KB 4-Way Cache 4-Way Cache 4-Way Cache 4-Way Cache 008E 0000h 64KB 32KB 32KB 008F 0000h 008F 8000h 008F FFFFh Figure 6-4. L2 Memory Configurations Global addresses that are accessible to all masters in the system are in all memory local to the processors. In addition, local memory can be accessed directly by the associated processor through aliased addresses, where the eight MSBs are masked to 0. The aliasing is handled within the CorePac and allows for common code to be run unmodified on multiple cores. For example, address location 0x10800000 is the global base address for CorePac0's L2 memory. CorePac0 can access this location by either using 0x10800000 or 0x00800000. Any other master on the device must use 0x10800000 only. Conversely, 0x00800000 can by used by any of the C66x CorePacs as their own L2 base addresses. For Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 C66x CorePac 59 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com CorePac0, as mentioned, this is equivalent to 0x10800000, for CorePac1 this is equivalent to 0x11800000, and for CorePac2 this is equivalent to 0x12800000. Local addresses should be used only for shared code or data, allowing a single image to be included in memory. Any code/data targeted to a specific core, or a memory region allocated during run time by a particular CorePac should always use the global address only. 6.2.4 Multicore Shared Memory SRAM The MSM SRAM configuration for the 66AK2Hxx device is as follows: • Memory size of 6144KB • Can be configured as shared L2 or shared L3 memory • Allows extension of external addresses from 2GB up to 8GB • Has built-in memory protection features The MSM SRAM is always configured as all SRAM. When configured as a shared L2, its contents can be cached in L1P and L1D. When configured in shared L3 mode, it’s contents can be cached in L2 also. For more details on external memory address extension and memory protection features, see the KeyStone Architecture Multicore Shared Memory Controller (MSMC) User's Guide. 6.2.5 L3 Memory The L3 ROM on the device is 128KB. The ROM contains software used to boot the device. There is no requirement to block accesses from this portion to the ROM. 6.3 Memory Protection Memory protection allows an operating system to define who or what is authorized to access L1D, L1P, and L2 memory. To accomplish this, the L1D, L1P, and L2 memories are divided into pages. There are 16 pages of L1P (2KB each), 16 pages of L1D (2KB each), and 32 pages of L2 (32KB each). The L1D, L1P, and L2 memory controllers in the C66x CorePac are equipped with a set of registers that specify the permissions for each memory page. Each page may be assigned with fully orthogonal user and supervisor read, write, and execute permissions. In addition, a page may be marked as either (or both) locally accessible or globally accessible. A local access is a direct DSP access to L1D, L1P, and L2, while a global access is initiated by a DMA (either IDMA or the EDMA3) or by other system masters. Note that EDMA or IDMA transfers programmed by the DSP count as global accesses. On a secure device, pages can be restricted to secure access only (default) or opened up for public, nonsecure access. The DSP and each of the system masters on the device are all assigned a privilege ID. It is possible to specify only whether memory pages are locally or globally accessible. The AIDx and LOCAL bits of the memory protection page attribute registers specify the memory page protection scheme, see Table 6-1. Table 6-1. Available Memory Page Protection Schemes AIDx BIT (1) LOCAL BIT DESCRIPTION 0 0 No access to memory page is permitted. 0 1 Only direct access by DSP is permitted. 1 0 Only accesses by system masters and IDMA are permitted (includes EDMA and IDMA accesses initiated by the DSP). 1 1 All accesses permitted. (1) x = 0, 1, 2, 3, 4, 5 60 C66x CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Faults are handled by software in an interrupt (or an exception, programmable within the CorePac interrupt controller) service routine. A DSP or DMA access to a page without the proper permissions will: • Block the access — reads return 0, writes are ignored • Capture the initiator in a status register — ID, address, and access type are stored • Signal the event to the DSP interrupt controller The software is responsible for taking corrective action to respond to the event and resetting the error status in the memory controller. For more information on memory protection for L1D, L1P, and L2, see the TMS320C66x DSP CorePac User's Guide. 6.4 Bandwidth Management When multiple requestors contend for a single C66x CorePac resource, the conflict is resolved by granting access to the highest priority requestor. The following four resources are managed by the bandwidth management control hardware: • Level 1 Program (L1P) SRAM/Cache • Level 1 Data (L1D) SRAM/Cache • Level 2 (L2) SRAM/Cache • Memory-mapped registers configuration bus The priority level for operations initiated within the C66x CorePac are declared through registers in the CorePac. These operations are: • DSP-initiated transfers • User-programmed cache coherency operations • IDMA-initiated transfers The priority level for operations initiated outside the CorePac by system peripherals is declared through the Priority Allocation Register (PRI_ALLOC). System peripherals with no fields in PRI_ALLOC have their own registers to program their priorities. More information on the bandwidth management features of the CorePac can be found in the TMS320C66x DSP CorePac User's Guide. 6.5 Power-Down Control The C66x CorePac supports the ability to power-down various parts of the CorePac. The power-down controller (PDC) of the CorePac can be used to power down L1P, the cache control hardware, the DSP, and the entire CorePac. These power-down features can be used to design systems for lower overall system power requirements. NOTE The 66AK2Hxx does not support power-down modes for the L2 memory at this time. More information on the power-down features of the C66x CorePac can be found in the TMS320C66x DSP CorePac User's Guide. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 C66x CorePac 61 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 6.6 www.ti.com C66x CorePac Revision The version and revision of the C66x CorePac can be read from the CorePac Revision ID Register (MM_REVID) at address 0181 2000h. The MM_REVID register is shown in Figure 6-5 and described in Table 6-2. The C66x CorePac revision is dependent on the silicon revision being used. Figure 6-5. CorePac Revision ID Register (MM_REVID) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 VERSION R-n 9 8 7 6 REVISION R-n 5 4 3 2 1 0 Legend: R = Read only; R/W = Read/Write; -n = value after reset Table 6-2. CorePac Revision ID Register (MM_REVID) Field Descriptions Bit Name Value Description 31-16 VERSION 0009h Version of the C66x CorePac implemented on the device. 15-0 REVISION xxxxh Revision of the C66x CorePac version implemented on this device. 0000h = silicon revision 1.0 0002h = silicon revision 1.1 0003h = silicon revisions 2.0, 3.0, and 3.1 6.7 C66x CorePac Register Descriptions See the TMS320C66x DSP CorePac User's Guide for register offsets and definitions. 62 C66x CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 7 ARM CorePac The ARM CorePac is added in the 66AK2Hxx to enable the ability for layer 2 and layer 3 processing onchip. Operations such as traffic control, local O&M, NBAP/FP termination, and SCTP processing can all be performed with the Cortex-A15 processor core. The ARM CorePac of the 66AK2Hxx integrates one or more Cortex-A15 processor clusters with additional logic for bus protocol conversion, emulation, interrupt handling, and debug related enhancements. The Cortex-A15 processor is an ARMv7A-compatible, multi-issue out-of-order superscalar execution engine with integrated L1 caches. The implementation also supports advanced SIMDv2 (NEON technology) and VFPv4 (vector floating point) architecture extensions, security, virtualization, LPAE (large physical address extension), and multiprocessing extensions. The ARM CorePac includes a 4MB L2 cache and support for AMBA4 AXI and AXI coherence extension (ACE) protocols. An interrupt controller is included in the ARM CorePac to handle host interrupt requests in the system. For more information, see the KeyStone II Architecture ARM CorePac User's Guide. The ARM CorePac has three functional clock domains, including a high-frequency clock domain used by the Cortex-A15. The high-frequency domain is isolated from the rest of the device by asynchronous bridges. Figure 7-1 and Figure 7-2 show the ARM CorePac. KeyStone II ARM CorePac (Quad Core) ARM ARM Cluster 480 SPI Interrupts Generic Interrupt Controller 400 4 MB L2 Cache ARM INTC 16 PPI VBUSP2AXI Bridge 64 Bits Global Time Base Counter Timer 0 - 3 TeraNet (CFG) 32KB L1 P-Cache 32KB L1 D-Cache 32KB L1 P-Cache APB 32KB L1 D-Cache APB CTM 32KB L1 D-Cache Debug SubSystem APB CTI/CTM ARM A15 Main PLL APB MUX PTM (´4) Debug ARM A15 32KB L1 P-Cache ATB ATB 32KB L1 D-Cache TeraNet (DMA) OCP ARM Trace ARM A15 ARM CorePac Clock Boot Config VBUSP ARM A15 32KB L1 P-Cache Endian CFG STM ATB L2 Cache Control and Snoop Control Unit IRQ, FIQ, VIRQ, VFIQ CTI (´4) ARM VBUSP Registers AXI-VBUS Master VBUSP 256b VBUSM TeraNet (CFG) MSMC DDR3 ARM A15 Core Clock PSC ARM PLL Copyright © 2016, Texas Instruments Incorporated Figure 7-1. 66AK2H12 ARM CorePac Block Diagram Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 ARM CorePac 63 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com KeyStone II ARM CorePac (Dual Core) ARM ARM Cluster Generic Interrupt Controller 400 480 SPI Interrupts 4 MB L2 Cache ARM INTC ATB 8 PPI VBUSP2AXI Bridge 64 Bits Global Time Base Counter Timer 0 - 3 TeraNet (CFG) 32KB L1 P-Cache ATB APB MUX APB Debug SubSystem PTM (´4) Debug TeraNet (DMA) OCP ARM Trace APB APB CTI/CTM ARM A15 ARM CorePac Clock Boot Config 32KB L1 D-Cache ATB 32KB L1 P-Cache Endian CFG VBUSP ARM A15 L2 Cache Control and Snoop Control Unit IRQ, FIQ, VIRQ, VFIQ STM Main PLL CTM 32KB L1 D-Cache CTI (´4) ARM VBUSP Registers AXI-VBUS Master VBUSP 256b VBUSM TeraNet (CFG) MSMC DDR3 ARM A15 Core Clock PSC ARM PLL Copyright © 2016, Texas Instruments Incorporated Figure 7-2. 66AK2H06 ARM CorePac Block Diagram 64 ARM CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 7.1 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Features The key features of the Quad Core ARM CorePac are as follows: • One or more Cortex-A15 processors, each containing: – Cortex-A15 processor revision R2P4. – ARM architecture version 7 ISA. – Multi-issue, out-of-order, superscalar pipeline. – L1 and L2 instruction and data cache of 32KB, 2-way, 16 word line with 128-bit interface. – Integrated L2 cache of 4MB, 16-way, 16-word line, 128-bit interface to L1 along with ECC/parity. – Includes the NEON™ media coprocessor (NEON), which implements the advanced SIMDv2 media processing architecture and the VFPv4 Vector Floating Point architecture. – The external interface uses the AXI protocol configured to 128-bit data width. – Includes the System Trace Macrocell (STM) support for noninvasive debugging. – Implements the ARMv7 debug with watchpoint and breakpoint registers and 32-bit advanced peripheral bus (APB) slave interface to CoreSight™ debug systems. • Interrupt controller – Supports up to 480 interrupt requests • Emulation/debug – Compatible with CoreSight architecture 7.2 System Integration The ARM CorePac integrates the following group of submodules. • Cortex-A15 Processors: Provides a high processing capability, including the NEON technology for mobile multimedia acceleration. The Cortex-A15 communicates with the rest of the ARM CorePac through an AXI bus with an AXI2VBUSM bridge and receives interrupts from the ARM CorePac interrupt controller (ARM INTC). • Interrupt Controller: Handles interrupts from modules outside of the ARM CorePac (for details, see Section 7.3.3). • Clock Divider: Provides the required divided clocks to the internal modules of the ARM CorePac and has a clock input from the ARM PLL and the Main PLL • In-Circuit Emulator: Fully compatible with CoreSight architecture and enables debugging capabilities. 7.3 7.3.1 ARM Cortex-A15 Processor Overview The ARM Cortex-A15 processor incorporates the technologies available in the ARM7™ architecture. These technologies include NEON for media and signal processing and Jazelle® RCT for acceleration of real-time compilers, Thumb®-2 technology for code density, and the VFPv4 floating point architecture. For details, see the ARM Cortex-A15 Processor Technical Reference Manual. 7.3.2 Features Table 7-1 shows the features supported by the Cortex-A15 processor core. Table 7-1. Cortex-A15 Processor Core Supported Features FEATURES DESCRIPTION ARM version 7-A ISA Standard Cortex-A15 processor instruction set + Thumb2, ThumbEE, JazelleX Java accelerator, and media extensions Backward compatible with previous ARM ISA versions Cortex-A15 processor version R2P4 Integer core Main core for processing integer instructions Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 ARM CorePac 65 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 7-1. Cortex-A15 Processor Core Supported Features (continued) FEATURES DESCRIPTION NEON core Gives greatly enhanced throughput for media workloads and VFP-Lite support Architecture Extensions Security, virtualization and LPAE (40-bit physical address) extensions L1 Lcache and Dcache 32KB, 2-way, 16 word line, 128 bit interface L2 cache 4096KB, 16-way, 16 word line, 128 bit interface to L1, ECC/Parity is supported shared between cores L2 valid bits cleared by software loop or by hardware Cache Coherency Support for coherent memory accesses between A15 cores and other noncore master peripherals (Ex: EDMA) in the DDR3A and MSMC SRAM space. Branch target address cache Dynamic branch prediction with Branch Target Buffer (BTB) and Global History Buffer (GHB), a return stack, and an indirect predictor Enhanced memory management unit Mapping sizes are 4KB, 64KB, 1MB, and 16MB Buses 128b AXI4 internal bus from Cortex-A15 converted to a 256b VBUSM to interface (through the MSMC) with MSMC SRAM, DDR EMIF, ROM, Interrupt controller and other system peripherals Noninvasive Debug Support Processor instruction trace using 4x Program Trace Macrocell (CoreSight PTM), Data trace (print-f style debug) using System Trace Macrocell (CoreSight STM) and Performance Monitoring Units (PMU) Misc Debug Support JTAG based debug and Cross triggering Clocking Dedicated ARM PLL for flexible clocking scenarios Voltage SmartReflex voltage domain for automatic voltage scaling Power Support for standby modes and separate core power domains for additional leakage power reduction 7.3.3 ARM Interrupt Controller The ARM CorePac interrupt controller (AINTC) is responsible for prioritizing all service requests from the system peripherals and the secondary interrupt controller CIC2 and then generating either nIRQ or nFIQ to the Cortex-A15 processor. The type of the interrupt (nIRQ or nFIQ) and the priority of the interrupt inputs are programmable. The AINTC interfaces to the Cortex-A15 processor via the AXI port through an VBUS2AXI bridge and runs at half the processor speed. It has the capability to handle up to 480 requests, which can be steered/prioritized as A15 nFIQ or nIRQ interrupt requests. The general features of the AINTC are: • Up to 480 level sensitive shared peripheral interrupts (SPI) inputs • Individual priority for each interrupt input • Each interrupt can be steered to nFIQ or nIRQ • Independent priority sorting for nFIQ and nIRQ • Secure mask flag On the chip level, there is a dedicated chip level interrupt controller to serve the ARM interrupt controller. See Section 8.3 for more details. Figure 7-3 and Figure 7-4 show an overall view of the ARM CorePac Interrupt Controller. 66 ARM CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 ARM INTC Peripherals 480 SPI Interrupts CIC2 CPU/6 Clock Generic Interrupt Controller 400 Global Time Base Counter GTB Counter Clock Power On Reset VBUSP2AXI Bridge VBUSP Interface FIQ, IRQ, Virtual FIQ, Virtual IRQ 8 PPIs 64 Bits Cortex A15 16 Software Generated Inputs Figure 7-3. ARM Interrupt Controller for Two Cortex-A15 Processor Cores ARM INTC Peripherals 480 SPI Interrupts CIC2 CPU/6 Clock Generic Interrupt Controller 400 Global Time Base Counter GTB Counter Clock Power On Reset VBUSP2AXI Bridge VBUSP Interface FIQ, IRQ, Virtual FIQ, Virtual IRQ 16 PPIs 64 Bits Cortex A15 16 Software Generated Inputs Figure 7-4. ARM Interrupt Controller for Four Cortex-A15 Processor Cores 7.3.4 Endianess The ARM CorePac can operate in either little-endian or big-endian mode. When the ARM CorePac is in little-endian mode and the rest of the system is in big-endian mode, the bridges in the ARM CorePac are responsible for performing the endian conversion. 7.4 CFG Connection The ARM CorePac has two slave ports. The 66AK2Hxx masters cannot access the ARM CorePac internal memory space. 1. Slave port 0 (TeraNet 3P_A) is a 32-bit-wide port used for the ARM Trace module. 2. Slave port 1 (TeraNet 3P_B) is a 32-bit-wide port used to access the rest of the system configuration. 7.5 Main TeraNet Connection One master port comes out of the ARM CorePac. The master port is a 256-bit-wide port for the transactions going to the MSMC and DDR_EMIF data spaces. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 ARM CorePac 67 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 7.6 7.6.1 www.ti.com Clocking and Reset Clocking The ARM CorePac includes a dedicated embedded DPLL (ARM PLL). The Cortex-A15 processor core clocks are sourced from this ARM PLL Controller. The Cortex-A15 processor core clock has a maximum frequency of 1.4 GHz. The ARM CorePac subsytem also uses the SYSCLK1 clock source from the main PLL which is locally divided (/1, /3 and /6) and provided to certain submodules inside the ARM CorePac. AINTC sub module runs at a frequency of SYSCLK1/6. 7.6.2 Reset The ARM CorePac does not support local reset. It is reset whenever the device is under reset. In addition, the interrupt controller (AINTC) can only be reset during POR and RESETFULL. AINTC also resets whenever device is under reset. For the complete programming model, refer to the KeyStone II Architecture ARM CorePac User's Guide. 68 ARM CorePac Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 8 Memory, Interrupts, and EDMA for 66AK2Hxx 8.1 Memory Map Summary for 66AK2Hxx Table 8-1 shows the memory map address ranges of the device. Table 8-1. Device Memory Map Summary for 66AK2Hxx PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0000 0000 00 0003 FFFF 256K ARM ROM Reserved ARM ROM 00 0004 0000 00 007F FFFF 8M-256K Reserved Reserved Reserved 00 0080 0000 00 008F FFFF 1M Reserved L2 SRAM L2 SRAM 00 0090 0000 00 00DF FFFF 5M Reserved Reserved Reserved 00 00E0 0000 00 00E0 7FFF 32K Reserved L1P SRAM L1P SRAM 00 00E0 8000 00 00EF FFFF 1M-32K Reserved Reserved Reserved 00 00F0 0000 00 00F0 7FFF 32K Reserved L1D SRAM L1D SRAM 00 00F0 8000 00 00FF FFFF 1M-32K Reserved Reserved Reserved 00 0100 0000 00 0100 FFFF 64K ARM AXI2VBUSM Master Registers C66x CorePac registers C66x CorePac registers 00 0101 0000 00 010F FFFF 1M-64K Reserved C66x CorePac registers C66x CorePac registers 00 0110 0000 00 0110 FFFF 64K ARM STM stimulus ports C66x CorePac registers C66x CorePac registers 00 0111 0000 00 01BF FFFF 11M-64K Reserved C66x CorePac registers C66x CorePac registers 00 01C0 0000 00 01CF FFFF 1M Reserved Reserved Reserved 00 01D0 0000 00 01D0 007F 128 Tracer_MSMC0_CFG Tracer_MSMC0_CFG Tracer_MSMC0_CFG 00 01D0 0080 00 01D0 7FFF 32K-128 Reserved Reserved Reserved 00 01D0 8000 00 01D0 807F 128 Tracer_MSMC1_CFG Tracer_MSMC1_CFG Tracer_MSMC1_CFG 00 01D0 8080 00 01D0 FFFF 32K-128 Reserved Reserved Reserved 00 01D1 0000 00 01D1 007F 128 Tracer_MSMC2_CFG Tracer_MSMC2_CFG Tracer_MSMC2_CFG 00 01D1 0080 00 01D1 7FFF 32K-128 Reserved Reserved Reserved 00 01D1 8000 00 01D1 807F 128 Tracer_MSMC3_CFG Tracer_MSMC3_CFG Tracer_MSMC3_CFG 00 01D1 8080 00 01D1 FFFF 32K-128 Reserved Reserved Reserved 00 01D2 0000 00 01D2 007F 128 Tracer_QM_M_CFG Tracer_QM_M_CFG Tracer_QM_M_CFG 00 01D2 0080 00 01D2 7FFF 32K-128 Reserved Reserved Reserved 00 01D2 8000 00 01D2 807F 128 Tracer_DDR3A_CFG Tracer_DDR3A_CFG Tracer_DDR3A_CFG 00 01D2 8080 00 01D2 FFFF 32K-128 Reserved Reserved Reserved 00 01D3 0000 00 01D3 007F 128 Tracer_SM_CFG Tracer_SM_CFG Tracer_SM_CFG 00 01D3 0080 00 01D3 7FFF 32K-128 Reserved Reserved Reserved 00 01D3 8000 00 01D3 807F 128 Tracer_QM_CFG1_CFG Tracer_QM_CFG1_CFG Tracer_QM_CFG1_CFG 00 01D3 8080 00 01D3 FFFF 32K-128 Reserved Reserved Reserved 00 01D4 0000 00 01D4 007F 128 Tracer_CFG_CFG Tracer_CFG_CFG Tracer_CFG_CFG 00 01D4 0080 00 01D4 7FFF 32K-128 Reserved Reserved Reserved 00 01D4 8000 00 01D4 807F 128 Tracer_L2_0_CFG Tracer_L2_0_CFG Tracer_L2_0_CFG 00 01D4 8080 00 01D4 FFFF 32K-128 Reserved Reserved Reserved 00 01D5 0000 00 01D5 007F 128 Tracer_L2_1_CFG Tracer_L2_1_CFG Tracer_L2_1_CFG 00 01D5 0080 00 01D5 7FFF 32K-128 Reserved Reserved Reserved 00 01D5 8000 00 01D5 807F 128 Tracer_L2_2_CFG Tracer_L2_2_CFG Tracer_L2_2_CFG 00 01D5 8080 00 01D5 FFFF 32K-128 Reserved Reserved Reserved 00 01D6 0000 00 01D6 007F 128 Tracer_L2_3_CFG Tracer_L2_3_CFG Tracer_L2_3_CFG 00 01D6 0080 00 01D6 7FFF 32K-128 Reserved Reserved Reserved 00 01D6 8000 00 01D6 807F 128 Tracer_L2_4_CFG Tracer_L2_4_CFG Tracer_L2_4_CFG 00 01D6 8080 00 01D6 FFFF 32K-128 Reserved Reserved Reserved 00 01D7 0000 00 01D7 007F 128 Tracer_L2_5_CFG Tracer_L2_5_CFG Tracer_L2_5_CFG 00 01D7 0080 00 01D7 7FFF 32K-128 Reserved Reserved Reserved 00 01D7 8000 00 01D7 807F 128 Tracer_L2_6_CFG Tracer_L2_6_CFG Tracer_L2_6_CFG Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 69 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 01D7 8080 00 01D7 FFFF 32K-128 Reserved Reserved Reserved 00 01D8 0000 00 01D8 007F 128 Tracer_L2_7_CFG Tracer_L2_7_CFG Tracer_L2_7_CFG 00 01D8 0080 00 01D8 7FFF 32K-128 Reserved Reserved Reserved 00 01D8 8000 00 01D8 807F 128 Reserved Reserved Reserved 00 01D8 8080 00 01D8 8FFF 32K-128 Reserved Reserved Reserved 00 01D9 0000 00 01D9 007F 128 Reserved Reserved Reserved 00 01D9 0080 00 01D9 7FFF 32K-128 Reserved Reserved Reserved 00 01D9 8000 00 01D9 807F 128 Reserved Reserved Reserved 00 01D9 8080 00 01D9 FFFF 32K-128 Reserved Reserved Reserved 00 01DA 0000 00 01DA 007F 128 Tracer_QM_CFG2_CFG Tracer_QM_CFG2_CFG Tracer_QM_CFG2_CFG 00 01DA 0080 00 01DA 7FFF 32K-128 Reserved Reserved Reserved 00 01DA 8000 00 01DA 807F 128 Reserved Reserved Reserved 00 01DA 8080 00 01DA FFFF 32K-128 Reserved Reserved Reserved 00 01DB 0000 00 01DB 007F 128 Tracer_DDR3B_CFG Tracer_DDR3B_CFG Tracer_DDR3B_CFG 00 01DB 0080 00 01DB 7FFF 32K-128 Reserved Reserved Reserved 00 01DB 8000 00 01DB 807F 128 Reserved Reserved Reserved 00 01DB 8080 00 01DB 8FFF 32K-128 Reserved Reserved Reserved 00 01DC 0000 00 01DC 007F 128 Tracer_TPCC0_4_CFG Tracer_TPCC0_4_CFG Tracer_TPCC0_4_CFG 00 01DC 0080 00 01DC 7FFF 32K-128 Reserved Reserved Reserved 00 01DC 8000 00 01DC 807F 128 Tracer_TPCC1_2_3_CFG Tracer_TPCC1_2_3_CFG Tracer_TPCC1_2_3_CFG 00 01DC 8080 00 01DC FFFF 32K-128 Reserved Reserved Reserved 00 01DD 0000 00 01DD 007F 128 Tracer_INTC_CFG Tracer_INTC_CFG Tracer_INTC_CFG 00 01DD 0080 00 01DD 7FFF 32K-128 Reserved Reserved Reserved 00 01DD 8000 00 01DD 807F 128 Tracer_MSMC4_CFG Tracer_MSMC4_CFG Tracer_MSMC4_CFG 00 01DD 8080 00 01DD FFFF 32K-128 Reserved Reserved Reserved 00 01DE 0000 00 01DE 007F 128 Tracer_MSMC5_CFG Tracer_MSMC5_CFG Tracer_MSMC5_CFG 00 01DE 0000 00 01DE 007F 128 Tracer_MSMC6_CFG Tracer_MSMC6_CFG Tracer_MSMC6_CFG 00 01DE 0000 00 01DE 007F 128 Tracer_MSMC7_CFG Tracer_MSMC7_CFG Tracer_MSMC7_CFG 00 01DE 0080 00 01DE 7FFF 32K-384 Reserved Reserved Reserved 00 01DE 8000 00 01DE 807F 128 Tracer_SPI_ROM_EMIF16_CFG Tracer_SPI_ROM_EMIF16_CFG Tracer_SPI_ROM_EMIF16_CFG 00 01DE 8080 00 01DF FFFF 64K-128 Reserved Reserved Reserved 00 01E0 0000 00 01E3 FFFF 256K Reserved Reserved Reserved 00 01E4 0000 00 01E4 3FFF 16K Reserved Reserved Reserved 00 01E4 4000 00 01E7 FFFF 240k Reserved Reserved Reserved 00 01E8 0000 00 01E8 3FFF 16K ARM CorePac VBUSP Memory Mapped Registers ARM CorePac VBUSP Memory Mapped Registers ARM CorePac VBUSP Memory Mapped Registers 00 01E8 4000 00 01EB FFFF 240k Reserved Reserved Reserved 00 01EC 0000 00 01EF FFFF 256K Reserved Reserved Reserved 00 01F0 0000 00 01F7 FFFF 512K Reserved Reserved Reserved 00 01F8 0000 00 01F8 FFFF 64K Reserved Reserved Reserved 00 01F9 0000 00 01F9 FFFF 64K Reserved Reserved Reserved 00 01FA 0000 00 01FB FFFF 128K Reserved Reserved Reserved 00 01FC 0000 00 01FD FFFF 128K Reserved Reserved Reserved 00 01FE 0000 00 01FF FFFF 128K Reserved Reserved Reserved 00 0200 0000 00 020F FFFF 1M Network Coprocessor (Packet Accelerator, 1-gigabit Ethernet switch subsystem and Security Accelerator) Network Coprocessor (Packet Accelerator, 1-gigabit Ethernet switch subsystem and Security Accelerator) Network Coprocessor (Packet Accelerator, 1-gigabit Ethernet switch subsystem and Security Accelerator) 00 0210 0000 00 0210 FFFF 64K Reserved Reserved Reserved 00 0211 0000 00 0211 FFFF 64K Reserved Reserved Reserved 00 0212 0000 00 0213 FFFF 128K Reserved Reserved Reserved 00 0214 0000 00 0215 FFFF 128K Reserved Reserved Reserved 70 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0216 0000 00 0217 FFFF 128K Reserved Reserved Reserved 00 0218 0000 00 0218 7FFF 32k Reserved Reserved Reserved 00 0218 8000 00 0218 FFFF 32k Reserved Reserved Reserved 00 0219 0000 00 0219 FFFF 64k Reserved Reserved Reserved 00 021A 0000 00 021A FFFF 64K Reserved Reserved Reserved 00 021B 0000 00 021B FFFF 64K Reserved Reserved Reserved 00 021C 0000 00 021C 03FF 1K Reserved Reserved Reserved 00 021C 0400 00 021C 3FFF 15K Reserved Reserved Reserved 00 021C 4000 00 021C 43FF 1K Reserved Reserved Reserved 00 021C 4400 00 021C 5FFF 7K Reserved Reserved Reserved 00 021C 6000 00 021C 63FF 1K Reserved Reserved Reserved 00 021C 6400 00 021C 7FFF 7K Reserved Reserved Reserved 00 021C 8000 00 021C 83FF 1K Reserved Reserved Reserved 00 021C 8400 00 021C FFFF 31K Reserved Reserved Reserved 00 021D 0000 00 021D 00FF 256 Reserved Reserved Reserved 00 021D 0100 00 021D 3FFF 16K Reserved Reserved Reserved 00 021D 4000 00 021D 40FF 256 Reserved Reserved Reserved 00 021D 4100 00 021D 7FFF 16K Reserved Reserved Reserved 00 021D 8000 00 021D 80FF 256 Reserved Reserved Reserved 00 021D 8100 00 021D BFFF 16K Reserved Reserved Reserved 00 021D C000 00 021D C0FF 256 Reserved Reserved Reserved 00 021D C100 00 021D EFFF 12K-256 Reserved Reserved Reserved 00 021D F000 00 021D F07F 128 Reserved Reserved Reserved 00 021D F080 00 021D FFFF 4K-128 Reserved Reserved Reserved 00 021E 0000 00 021E FFFF 64K Reserved Reserved Reserved 00 021F 0000 00 021F 07FF 2K Reserved Reserved Reserved 00 021F 0800 00 021F 0FFF 2K Reserved Reserved Reserved 00 021F 1000 00 021F 17FF 2K Reserved Reserved Reserved 00 021F 1800 00 021F 3FFF 10K Reserved Reserved Reserved 00 021F 4000 00 021F 47FF 2K Reserved Reserved Reserved 00 021F 4800 00 021F 7FFF 14K Reserved Reserved Reserved 00 021F 8000 00 021F 87FF 2K Reserved Reserved Reserved 00 021F 8800 00 021F BFFF 14K Reserved Reserved Reserved 00 021F C000 00 021F C7FF 2K Reserved Reserved Reserved 00 021F C800 00 021F FFFF 14K Reserved Reserved Reserved 00 0220 0000 00 0220 007F 128 Timer0 Timer0 Timer0 00 0220 0080 00 0220 FFFF 64K-128 Reserved Reserved Reserved 00 0221 0000 00 0221 007F 128 Timer1 Timer1 Timer1 00 0221 0080 00 0221 FFFF 64K-128 Reserved Reserved Reserved 00 0222 0000 00 0222 007F 128 Timer2 Timer2 Timer2 00 0222 0080 00 0222 FFFF 64K-128 Reserved Reserved Reserved 00 0223 0000 00 0223 007F 128 Timer3 Timer3 Timer3 00 0223 0080 00 0223 FFFF 64K-128 Reserved Reserved Reserved 00 0224 0000 00 0224 007F 128 Timer4 (1) Timer4 (1) Timer4 (1) 00 0224 0080 00 0224 FFFF 64K-128 Reserved Reserved Reserved 00 0225 0000 00 0225 007F 128 Timer5 (1) Timer5 (1) Timer5 (1) 00 0225 0080 00 0225 FFFF 64K-128 Reserved Reserved Reserved 00 0226 0000 00 0226 007F 128 Timer6 (1) Timer6 (1) Timer6 (1) 00 0226 0080 00 0226 FFFF 64K-128 Reserved Reserved Reserved (1) 66AK2H12/14 only. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 71 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0227 0000 00 0227 007F 128 Timer7 (1) Timer7 (1) Timer7 (1) 00 0227 0080 00 0227 FFFF 64K-128 Reserved Reserved Reserved 00 0228 0000 00 0228 007F 128 Timer 8 Timer 8 Timer 8 00 0228 0080 00 0228 FFFF 64K-128 Reserved Reserved Reserved 00 0229 0000 00 0229 007F 128 Timer 9 Timer 9 Timer 9 00 0229 0080 00 0229 FFFF 64K-128 Reserved Reserved Reserved 00 022A 0000 00 022A 007F 128 Timer 10 Timer 10 Timer 10 00 022A 0080 00 022A FFFF 64K-128 Reserved Reserved Reserved 00 022B 0000 00 022B 007F 128 Timer 11 Timer 11 Timer 11 00 022B 0080 00 022B FFFF 64K-128 Reserved Reserved Reserved 00 022C 0000 00 022C 007F 128 Timer 12 Timer 12 Timer 12 00 022C 0080 00 022C FFFF 64K-128 Reserved Reserved Reserved 00 022D 0000 00 022D 007F 128 Timer 13 Timer 13 Timer 13 00 022D 0080 00 022D FFFF 64K-128 Reserved Reserved Reserved 00 022E 0000 00 022E 007F 128 Timer 14 Timer 14 Timer 14 00 022E 0080 00 022E FFFF 64K-128 Reserved Reserved Reserved 00 022F 0000 00 022F 007F 128 Timer 15 Timer 15 Timer 15 00 022F 0080 00 022F 00FF 128 Timer 16 Timer 16 Timer 16 00 022F 0100 00 022F 017F 128 Timer 17 Timer 17 Timer 17 00 022F 0180 00 022F 01FF 128 Timer 18 (1) Timer 18 (1) Timer 18 (1) (1) (1) Timer 19 (1) 00 022F 0200 00 022F 027F 128 Timer 19 00 0230 0000 00 0230 FFFF 64K Reserved Reserved Reserved 00 0231 0000 00 0231 01FF 512 PLL Controller PLL Controller PLL Controller 00 0231 0200 00 0231 9FFF 40K-512 Reserved Reserved Reserved 00 0231 A000 00 0231 BFFF 8K HyperLink0 SerDes Config HyperLink0 SerDes Config HyperLink0 SerDes Config 00 0231 C000 00 0231 DFFF 8K HyperLink1 SerDes Config HyperLink1 SerDes Config HyperLink1 SerDes Config 00 0231 E000 00 0231 FFFF 8K 10GbE SerDes Config (66AK2H14 only) 10GbE SerDes Config (66AK2H14 only) 10GbE SerDes Config (66AK2H14 only) 00 0232 0000 00 0232 3FFF 16K PCIE SerDes Config PCIE SerDes Config PCIE SerDes Config 00 0232 4000 00 0232 5FFF 8K Reserved Reserved Reserved 00 0232 6000 00 0232 7FFF 8K Reserved Reserved Reserved 00 0232 8000 00 0232 8FFF 4K DDRB PHY Config DDRB PHY Config DDRB PHY Config 00 0232 9000 00 0232 9FFF 4K DDRA PHY Config DDRA PHY Config DDRA PHY Config 00 0232 A000 00 0232 BFFF 8K PA SerDes Config PA SerDes Config PA SerDes Config 00 0232 C000 00 0232 DFFF 8K SRIO SerDes Config SRIO SerDes Config SRIO SerDes Config 00 0232 E000 00 0232 EFFF 4K Reserved Reserved Reserved 00 0232 F000 00 0232 FFFF 4K Reserved Reserved Reserved 00 0233 0000 00 0233 03FF 1K SmartReflex0 SmartReflex0 SmartReflex0 00 0233 0400 00 0233 07FF 1K SmartReflex1 SmartReflex1 SmartReflex1 00 0233 0400 00 0233 FFFF 62K Reserved Reserved Reserved 00 0234 0000 00 0234 00FF 256 Reserved Reserved Reserved 00 0234 0100 00 0234 3FFF 16K Reserved Reserved Reserved 00 0234 4000 00 0234 40FF 256 Reserved Reserved Reserved 00 0234 4100 00 0234 7FFF 16K Reserved Reserved Reserved 00 0234 8000 00 0234 80FF 256 Reserved Reserved Reserved 00 0234 8100 00 0234 BFFF 16K Reserved Reserved Reserved 00 0234 C000 00 0234 C0FF 256 Reserved Reserved Reserved 00 0234 C100 00 0234 FFFF 16K Reserved Reserved Reserved 00 0235 0000 00 0235 0FFF 4K Power sleep controller (PSC) Power sleep controller (PSC) Power sleep controller (PSC) 00 0235 1000 00 0235 FFFF 64K-4K Reserved Reserved Reserved 00 0236 0000 00 0236 03FF 1K Memory protection unit (MPU) 0 Memory protection unit (MPU) 0 Memory protection unit (MPU) 0 72 Timer 19 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0236 0400 00 0236 7FFF 31K Reserved Reserved Reserved 00 0236 8000 00 0236 83FF 1K Memory protection unit (MPU) 1 Memory protection unit (MPU) 1 Memory protection unit (MPU) 1 00 0236 8400 00 0236 FFFF 31K Reserved Reserved Reserved 00 0237 0000 00 0237 03FF 1K Memory protection unit (MPU) 2 Memory protection unit (MPU) 2 Memory protection unit (MPU) 2 00 0237 0400 00 0237 7FFF 31K Reserved Reserved Reserved 00 0237 8000 00 0237 83FF 1K Memory protection unit (MPU) 3 Memory protection unit (MPU) 3 Memory protection unit (MPU) 3 00 0237 8400 00 0237 FFFF 31K Reserved Reserved Reserved 00 0238 0000 00 0238 03FF 1K Memory protection unit (MPU) 4 Memory protection unit (MPU) 4 Memory protection unit (MPU) 4 00 0238 8000 00 0238 83FF 1K Memory protection unit (MPU) 5 Memory protection unit (MPU) 5 Memory protection unit (MPU) 5 00 0238 8400 00 0238 87FF 1K Memory protection unit (MPU) 6 Memory protection unit (MPU) 6 Memory protection unit (MPU) 6 00 0238 8800 00 0238 8BFF 1K Memory protection unit (MPU) 7 Memory protection unit (MPU) 7 Memory protection unit (MPU) 7 00 0238 8C00 00 0238 8FFF 1K Memory protection unit (MPU) 8 Memory protection unit (MPU) 8 Memory protection unit (MPU) 8 00 0238 9000 00 0238 93FF 1K Memory protection unit (MPU) 9 Memory protection unit (MPU) 9 Memory protection unit (MPU) 9 00 0238 9400 00 0238 97FF 1K Memory protection unit (MPU) 10 Memory protection unit (MPU) 10 Memory protection unit (MPU) 10 00 0238 9800 00 0238 9BFF 1K Memory protection unit (MPU) 11 Memory protection unit (MPU) 11 Memory protection unit (MPU) 11 00 0238 9C00 00 0238 9FFF 1K Memory protection unit (MPU) 12 Memory protection unit (MPU) 12 Memory protection unit (MPU) 12 00 0238 A000 00 0238 A3FF 1K Memory protection unit (MPU) 13 Memory protection unit (MPU) 13 Memory protection unit (MPU) 13 00 0238 A400 00 0238 A7FF 1K Memory protection unit (MPU) 14 Memory protection unit (MPU) 14 Memory protection unit (MPU) 14 00 0238 A800 00 023F FFFF 471K Reserved Reserved Reserved 00 0240 0000 00 0243 FFFF 256K Reserved Reserved Reserved 00 0244 0000 00 0244 3FFF 16K DSP trace formatter 0 DSP trace formatter 0 DSP trace formatter 0 00 0244 4000 00 0244 FFFF 48K Reserved Reserved Reserved 00 0245 0000 00 0245 3FFF 16K DSP trace formatter 1 DSP trace formatter 1 DSP trace formatter 1 00 0245 4000 00 0245 FFFF 48K Reserved Reserved Reserved 00 0246 0000 00 0246 3FFF 16K DSP trace formatter 2 DSP trace formatter 2 DSP trace formatter 2 00 0246 4000 00 0246 FFFF 48K Reserved Reserved Reserved 00 0247 0000 00 0247 3FFF 16K DSP trace formatter 3 DSP trace formatter 3 DSP trace formatter 3 00 0247 4000 00 0247 FFFF 48K Reserved Reserved Reserved 00 0248 0000 00 0248 3FFF 16K DSP trace formatter 4 DSP trace formatter 4 DSP trace formatter 4 00 0248 4000 00 0248 FFFF 48K Reserved Reserved Reserved 00 0249 0000 00 0249 3FFF 16K DSP trace formatter 5 DSP trace formatter 5 DSP trace formatter 5 00 0249 4000 00 0249 FFFF 48K Reserved Reserved Reserved 00 024A 0000 00 024A 3FFF 16K DSP trace formatter 6 DSP trace formatter 6 DSP trace formatter 6 00 024A 4000 00 024A FFFF 48K Reserved Reserved Reserved 00 024B 0000 00 024B 3FFF 16K DSP trace formatter 7 DSP trace formatter 7 DSP trace formatter 7 00 024B 4000 00 024B FFFF 48K Reserved Reserved Reserved 00 024C 0000 00 024C 01FF 512 Reserved Reserved Reserved 00 024C 0200 00 024C 03FF 1K-512 Reserved Reserved Reserved 00 024C 0400 00 024C 07FF 1K Reserved Reserved Reserved 00 024C 0800 00 024C FFFF 62K Reserved Reserved Reserved 00 024D 0000 00 024F FFFF 192K Reserved Reserved Reserved 00 0250 0000 00 0250 007F 128 Reserved Reserved Reserved 00 0250 0080 00 0250 7FFF 32K-128 Reserved Reserved Reserved 00 0250 8000 00 0250 FFFF 32K Reserved Reserved Reserved 00 0251 0000 00 0251 FFFF 64K Reserved Reserved Reserved 00 0252 0000 00 0252 03FF 1K Reserved Reserved Reserved 00 0252 0400 00 0252 FFFF 64K-1K Reserved Reserved Reserved 00 0253 0000 00 0253 007F 128 I C0 I C0 I2C0 00 0253 0080 00 0253 03FF 1K-128 Reserved Reserved Reserved 00 0253 0400 00 0253 047F 128 I2C1 I2C1 I2C1 2 2 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 73 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0253 0480 00 0253 07FF 1K-128 Reserved Reserved Reserved 00 0253 0800 00 0253 087F 128 I2C2 I2C2 I2C2 00 0253 0880 00 0253 0BFF 1K-128 Reserved Reserved Reserved 00 0253 0C00 00 0253 0C3F 64 UART0 UART0 UART0 00 0253 0C40 00 0253 FFFF 1K-64 Reserved Reserved Reserved 00 0253 1000 00 0253 103F 64 UART1 UART1 UART1 00 0253 1040 00 0253 FFFF 60K-64 Reserved Reserved Reserved 00 0254 0000 00 0255 FFFF 128K Reserved Reserved Reserved 00 0256 0000 00 0257 FFFF 128K ARM CorePac INTC (GIC400) Memory Mapped Registers ARM CorePac INTC (GIC400) Memory Mapped Registers ARM CorePac INTC (GIC400) Memory Mapped Registers 00 0258 0000 00 025F FFFF 512K Reserved Reserved Reserved 00 0260 0000 00 0260 1FFF 8K Secondary interrupt controller (INTC) 0 Secondary interrupt controller (INTC) 0 Secondary interrupt controller (INTC) 0 00 0260 2000 00 0260 3FFF 8K Reserved Reserved Reserved 00 0260 4000 00 0260 5FFF 8K Secondary interrupt controller (INTC) 1 Secondary interrupt controller (INTC) 1 Secondary interrupt controller (INTC) 1 00 0260 6000 00 0260 7FFF 8K Reserved Reserved Reserved 00 0260 8000 00 0260 9FFF 8K Secondary interrupt controller (INTC) 2 Secondary interrupt controller (INTC) 2 Secondary interrupt controller (INTC) 2 00 0260 A000 00 0260 BEFF 8K-256 Reserved Reserved Reserved 00 0260 BF00 00 0260 BFFF 256 GPIO Config GPIO Config GPIO Config 00 0260 C000 00 0261 BFFF 64K Reserved Reserved Reserved 00 0261 C000 00 0261 FFFF 16K Reserved Reserved Reserved 00 0262 0000 00 0262 0FFF 4K BOOTCFG chip-level registers BOOTCFG chip-level registers BOOTCFG chip-level registers 00 0262 1000 00 0262 FFFF 60K Reserved Reserved Reserved 00 0263 0000 00 0263 FFFF 64K USB PHY Config USB PHY Config USB PHY Config 00 0264 0000 00 0264 07FF 2K Semaphore Config Semaphore Config Semaphore Config 00 0264 0800 00 0264 FFFF 62K Reserved Reserved Reserved 00 0265 0000 00 0267 FFFF 192K Reserved Reserved Reserved 00 0268 0000 00 0268 FFFF 512K USB MMR Config USB MMR Config USB MMR Config 00 0270 0000 00 0270 7FFF 32K EDMA channel controller (TPCC) 0 EDMA channel controller (TPCC) 0 EDMA channel controller (TPCC) 0 00 0270 8000 00 0270 FFFF 32K EDMA channel controller (TPCC) 4 EDMA channel controller (TPCC) 4 EDMA channel controller (TPCC) 4 00 0271 0000 00 0271 FFFF 64K Reserved Reserved Reserved 00 0272 0000 00 0272 7FFF 32K EDMA channel controller (TPCC) 1 EDMA channel controller (TPCC) 1 EDMA channel controller (TPCC) 1 00 0272 8000 00 0272 FFFF 32K EDMA channel controller (TPCC) 3 EDMA channel controller (TPCC) 3 EDMA channel controller (TPCC) 3 00 0273 0000 00 0273 FFFF 64K Reserved Reserved Reserved 00 0274 0000 00 0274 7FFF 32K EDMA channel controller (TPCC) 2 EDMA channel controller (TPCC) 2 EDMA channel controller (TPCC) 2 00 0274 8000 00 0275 FFFF 96K Reserved Reserved Reserved 00 0276 0000 00 0276 03FF 1K EDMA TPCC0 transfer controller (TPTC) 0 EDMA TPCC0 transfer controller (TPTC) 0 EDMA TPCC0 transfer controller (TPTC) 0 00 0276 0400 00 0276 7FFF 31K Reserved Reserved Reserved 00 0276 8000 00 0276 83FF 1K EDMA TPCC0 transfer controller (TPTC) 1 EDMA TPCC0 transfer controller (TPTC) 1 EDMA TPCC0 transfer controller (TPTC) 1 00 0276 8400 00 0276 FFFF 31K Reserved Reserved Reserved 00 0277 0000 00 0277 03FF 1K EDMA TPCC1 transfer controller (TPTC) 0 EDMA TPCC1 transfer controller (TPTC) 0 EDMA TPCC1 transfer controller (TPTC) 0 00 0277 0400 00 0277 7FFF 31K Reserved Reserved Reserved 00 0277 8000 00 0277 83FF 1K EDMA TPCC1 transfer controller (TPTC) 1 EDMA TPCC1 transfer controller (TPTC) 1 EDMA TPCC1 transfer controller (TPTC) 1 00 0278 0400 00 0277 FFFF 31K Reserved Reserved Reserved 74 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 0278 0000 00 0278 03FF 1K EDMA TPCC1 transfer controller (TPTC) 2 EDMA TPCC1 transfer controller (TPTC) 2 EDMA TPCC1 transfer controller (TPTC) 2 00 0278 0400 00 0278 7FFF 31K Reserved Reserved Reserved 00 0278 8000 00 0278 83FF 1K EDMA TPCC1 transfer controller (TPTC) 3 EDMA TPCC1 transfer controller (TPTC) 3 EDMA TPCC1 transfer controller (TPTC) 3 00 0278 8400 00 0278 FFFF 31K Reserved Reserved Reserved 00 0279 0000 00 0279 03FF 1K EDMA TPCC2 transfer controller (TPTC) 0 EDMA TPCC2 transfer controller (TPTC) 0 EDMA TPCC2 transfer controller (TPTC) 0 00 0279 0400 00 0279 7FFF 31K Reserved Reserved Reserved 00 0279 8000 00 0279 83FF 1K EDMA TPCC2 transfer controller (TPTC) 1 EDMA TPCC2 transfer controller (TPTC) 1 EDMA TPCC2 transfer controller (TPTC) 1 00 0279 8400 00 0279 FFFF 31K Reserved Reserved Reserved 00 027A 0000 00 027A 03FF 1K EDMA TPCC2 transfer controller (TPTC) 2 EDMA TPCC2 transfer controller (TPTC) 2 EDMA TPCC2 transfer controller (TPTC) 2 00 027A 0400 00 027A 7FFF 31K Reserved Reserved Reserved 00 027A 8000 00 027A 83FF 1K EDMA TPCC2 transfer controller (TPTC) 3 EDMA TPCC2 transfer controller (TPTC) 3 EDMA TPCC2 transfer controller (TPTC) 3 00 027A 8400 00 027A FFFF 31K Reserved Reserved Reserved 00 027B 0000 00 027B 03FF 1K EDMA TPCC3 transfer controller (TPTC) 0 EDMA TPCC3 transfer controller (TPTC) 0 EDMA TPCC3 transfer controller (TPTC) 0 00 027B 0400 00 027B 7FFF 31K Reserved Reserved Reserved 00 027B 8000 00 027B 83FF 1K EDMA TPCC3 transfer controller (TPTC) 1 EDMA TPCC3 transfer controller (TPTC) 1 EDMA TPCC3 transfer controller (TPTC) 1 00 027B 8400 00 027B 87FF 1K EDMA TPCC4 transfer controller (TPTC) 0 EDMA TPCC4 transfer controller (TPTC) 0 EDMA TPCC4 transfer controller (TPTC) 0 00 027B 8800 00 027B 8BFF 1K EEDMA TPCC4 transfer controller (TPTC) 1 EEDMA TPCC4 transfer controller (TPTC) 1 EEDMA TPCC4 transfer controller (TPTC) 1 00 027B 8C00 00 027B FFFF 29K Reserved Reserved Reserved 00 027C 0000 00 027C 03FF 1K Reserved Reserved Reserved 00 027C 0400 00 027C FFFF 63K Reserved Reserved Reserved 00 027D 0000 00 027D 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac0 CorePac0 CorePac0 00 027D 4000 00 027D 7FFF 16K TBR_SYS_ARM CorePac - Trace buffer - ARM CorePac TBR_SYS_ARM CorePac - Trace buffer - ARM CorePac TBR_SYS_ARM CorePac - Trace buffer - ARM CorePac 00 027D 8000 00 027D FFFF 32K Reserved Reserved Reserved 00 027E 0000 00 027E 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac1 CorePac1 CorePac1 00 027E 4000 00 027E FFFF 48K Reserved 00 027F 0000 00 027F 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac2 CorePac2 CorePac2 00 027F 4000 00 027F FFFF 48K Reserved 00 0280 0000 00 0280 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac3 CorePac3 CorePac3 00 0280 4000 00 0280 FFFF 48K Reserved 00 0281 0000 00 0281 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac4 (66AK2H12/14 only) CorePac4 (66AK2H12/14 only) CorePac4 (66AK2H12/14 only) 00 0281 4000 00 0281 FFFF 48K Reserved 00 0282 0000 00 0282 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac5 (66AK2H12/14 only) CorePac5 (66AK2H12/14 only) CorePac5 (66AK2H12/14 only) 00 0282 4000 00 0282 FFFF 48K Reserved 00 0283 0000 00 0283 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac6 (66AK2H12/14 only) CorePac6 (66AK2H12/14 only) CorePac6 (66AK2H12/14 only) 00 0283 4000 00 0283 FFFF 48K Reserved 00 0284 0000 00 0284 3FFF 16K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) CorePac7 (66AK2H12/14 only) CorePac7 (66AK2H12/14 only) CorePac7 (66AK2H12/14 only) 00 0284 4000 00 0284 FFFF 48K Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 75 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW 00 0285 0000 00 0285 7FFF 32K TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) - TI embedded trace buffer (TETB) system system system 00 0285 8000 00 0285 FFFF 32K Reserved Reserved Reserved 00 0286 0000 00 028F FFFF 640K Reserved Reserved Reserved 00 0290 0000 00 0293 FFFF 256K Serial RapidIO configuration (SRIO) Serial RapidIO configuration (SRIO) Serial RapidIO configuration (SRIO) 00 0294 0000 00 029F FFFF 768K Reserved Reserved Reserved 00 02A0 0000 00 02AF FFFF 1M Navigator configuration Navigator configuration Navigator configuration 00 02B0 0000 00 02BF FFFF 1M Navigator linking RAM Navigator linking RAM Navigator linking RAM 00 02C0 0000 00 02C0 FFFF 64K Reserved Reserved Reserved 00 02C1 0000 00 02C1 FFFF 64K Reserved Reserved Reserved 00 02C2 0000 00 02C3 FFFF 128K Reserved Reserved Reserved 00 02C4 0000 00 02C5 FFFF 128K Reserved Reserved Reserved 00 02C6 0000 00 02C7 FFFF 128K Reserved Reserved Reserved 00 02C8 0000 00 02C8 FFFF 64K Reserved Reserved Reserved 00 02C9 0000 00 02C9 FFFF 64K Reserved Reserved Reserved 00 02CA 0000 00 02CB FFFF 128K Reserved Reserved Reserved 00 02CC 0000 00 02CD FFFF 128K Reserved Reserved Reserved 00 02CE 0000 00 02EF FFFF 15M-896K Reserved Reserved Reserved 00 02F0 0000 00 02FF FFFF 1M 10GbE Config (66AK2H14 only) 10GbE Config (66AK2H14 only) 10GbE Config (66AK2H14 only) 00 0300 0000 00 030F FFFF 1M Debug_SS Configuration Debug_SS Configuration Debug_SS Configuration 00 0310 0000 00 07FF FFFF 79M Reserved Reserved Reserved 00 0800 0000 00 0801 FFFF 128K Reserved Extended memory controller (XMC) configuration Reserved 00 0802 0000 00 0BBF FFFF 60M-128K Reserved Reserved Reserved 00 0BC0 0000 00 0BCF FFFF 1M Multicore shared memory controller (MSMC) config Multicore shared memory controller (MSMC) config Multicore shared memory controller (MSMC) config 00 0BD0 0000 00 0BFF FFFF 3M Reserved Reserved Reserved 00 0C00 0000 00 0C5F FFFF 6M Multicore shared memory (MSM) Multicore shared memory (MSM) Multicore shared memory (MSM) 00 0C60 0000 00 0FFF FFFF 58M Reserved Reserved Reserved 00 1000 0000 00 107F FFFF 8M Reserved Reserved Reserved 00 1080 0000 00 108F FFFF 1M CorePac0 L2 SRAM CorePac0 L2 SRAM CorePac0 L2 SRAM 00 1090 0000 00 10DF FFFF 5M Reserved Reserved Reserved 00 10E0 0000 00 10E0 7FFF 32K CorePac0 L1P SRAM CorePac0 L1P SRAM CorePac0 L1P SRAM 00 10E0 8000 00 10EF FFFF 1M-32K Reserved Reserved Reserved 00 10F0 0000 00 10F0 7FFF 32K CorePac0 L1D SRAM CorePac0 L1D SRAM CorePac0 L1D SRAM 00 10F0 8000 00 117F FFFF 9M-32K Reserved Reserved Reserved 00 1180 0000 00 118F FFFF 1M CorePac1 L2 SRAM CorePac1 L2 SRAM CorePac1 L2 SRAM 00 1190 0000 00 11DF FFFF 5M Reserved Reserved Reserved 00 11E0 0000 00 11E0 7FFF 32K CorePac1 L1P SRAM CorePac1 L1P SRAM CorePac1 L1P SRAM 00 11E0 8000 00 11EF FFFF 1M-32K Reserved Reserved Reserved 00 11F0 0000 00 11F0 7FFF 32K CorePac1 L1D SRAM CorePac1 L1D SRAM CorePac1 L1D SRAM 00 11F0 8000 00 127F FFFF 9M-32K Reserved Reserved Reserved 00 1280 0000 00 128F FFFF 1M CorePac2 L2 SRAM CorePac2 L2 SRAM CorePac2 L2 SRAM 00 1290 0000 00 12DF FFFF 5M Reserved Reserved Reserved 00 12E0 0000 00 12E0 7FFF 32K CorePac2 L1P SRAM CorePac2 L1P SRAM CorePac2 L1P SRAM 00 12E0 8000 00 12EF FFFF 1M-32K Reserved Reserved Reserved 00 12F0 0000 00 12F0 7FFF 32K CorePac2 L1D SRAM CorePac2 L1D SRAM CorePac2 L1D SRAM 00 12F0 8000 00 137F FFFF 9M-32K Reserved Reserved Reserved 00 1380 0000 00 1388 FFFF 1M CorePac3 L2 SRAM CorePac3 L2 SRAM CorePac3 L2 SRAM 00 1390 0000 00 13DF FFFF 5M Reserved Reserved Reserved 00 13E0 0000 00 13E0 7FFF 32K CorePac3 L1P SRAM CorePac3 L1P SRAM CorePac3 L1P SRAM 76 DSP VIEW SOC VIEW Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 13E0 8000 00 13EF FFFF 1M-32K Reserved Reserved Reserved 00 13F0 0000 00 13F0 7FFF 32K CorePac3 L1D SRAM CorePac3 L1D SRAM CorePac3 L1D SRAM 00 13F0 8000 00 147F FFFF 9M-32K Reserved Reserved Reserved 00 1480 0000 00 148F FFFF 1M CorePac4 L2 SRAM (66AK2H12/14 only) CorePac4 L2 SRAM (66AK2H12/14 only) CorePac4 L2 SRAM (66AK2H12/14 only) 00 1490 0000 00 14DF FFFF 5M Reserved Reserved Reserved 00 14E0 0000 00 14E0 7FFF 32K CorePac4 L1P SRAM (66AK2H12/14 only) CorePac4 L1P SRAM (66AK2H12/14 only) CorePac4 L1P SRAM (66AK2H12/14 only) 00 14E0 8000 00 14EF FFFF 1M-32K Reserved Reserved Reserved 00 14F0 0000 00 14F0 7FFF 32K CorePac4 L1D SRAM (66AK2H12/14 only) CorePac4 L1D SRAM (66AK2H12/14 only) CorePac4 L1D SRAM (66AK2H12/14 only) 00 14F0 8000 00 157F FFFF 9M-32K Reserved Reserved Reserved 00 1580 0000 00 158F FFFF 1M CorePac5 L2 SRAM (66AK2H12/14 only) CorePac5 L2 SRAM (66AK2H12/14 only) CorePac5 L2 SRAM (66AK2H12/14 only) 00 1590 0000 00 15DF FFFF 5M Reserved Reserved Reserved 00 15E0 0000 00 15E0 7FFF 32K CorePac5 L1P SRAM (66AK2H12/14 only) CorePac5 L1P SRAM (66AK2H12/14 only) CorePac5 L1P SRAM (66AK2H12/14 only) 00 15E0 8000 00 15EF FFFF 1M-32K Reserved Reserved Reserved 00 15F0 0000 00 15F0 7FFF 32K CorePac5 L1D SRAM (66AK2H12/14 only) CorePac5 L1D SRAM (66AK2H12/14 only) CorePac5 L1D SRAM (66AK2H12/14 only) 00 15F0 8000 00 167F FFFF 9M-32K Reserved Reserved Reserved 00 1680 0000 00 168F FFFF 1M CorePac6 L2 SRAM (66AK2H12/14 only) CorePac6 L2 SRAM (66AK2H12/14 only) CorePac6 L2 SRAM (66AK2H12/14 only) 00 1690 0000 00 16DF FFFF 5M Reserved Reserved Reserved 00 16E0 0000 00 16E0 7FFF 32K CorePac6 L1P SRAM (66AK2H12/14 only) CorePac6 L1P SRAM (66AK2H12/14 only) CorePac6 L1P SRAM (66AK2H12/14 only) 00 16E0 8000 00 16EF FFFF 1M-32K Reserved Reserved Reserved 00 16F0 0000 00 16F0 7FFF 32K CorePac6 L1D SRAM (66AK2H12/14 only) CorePac6 L1D SRAM (66AK2H12/14 only) CorePac6 L1D SRAM (66AK2H12/14 only) 00 16F0 8000 00 177F FFFF 9M-32K Reserved Reserved Reserved 00 1780 0000 00 178F FFFF 1M CorePac7 L2 SRAM (66AK2H12/14 only) CorePac7 L2 SRAM (66AK2H12/14 only) CorePac7 L2 SRAM (66AK2H12/14 only) 00 1790 0000 00 17DF FFFF 5M Reserved Reserved Reserved 00 17E0 0000 00 17E0 7FFF 32K CorePac7 L1P SRAM (66AK2H12/14 only) CorePac7 L1P SRAM (66AK2H12/14 only) CorePac7 L1P SRAM (66AK2H12/14 only) 00 17E0 8000 00 17EF FFFF 1M-32K Reserved Reserved Reserved 00 17F0 0000 00 17F0 7FFF 32K CorePac7 L1D SRAM (66AK2H12/14 only) CorePac7 L1D SRAM (66AK2H12/14 only) CorePac7 L1D SRAM (66AK2H12/14 only) 00 17F0 8000 00 1FFF FFFF 129M-32K Reserved Reserved Reserved 00 2000 0000 00 200F FFFF 1M System trace manager (STM) configuration System trace manager (STM) configuration System trace manager (STM) configuration 00 2010 0000 00 201F FFFF 1M Reserved Reserved Reserved 00 2020 0000 00 205F FFFF 4M Reserved Reserved Reserved 00 2060 0000 00 206F FFFF 1M Reserved Reserved Reserved 00 2070 0000 00 207F FFFF 1M Reserved Reserved Reserved 00 2080 0000 00 208F FFFF 1M Reserved Reserved Reserved 00 2090 0000 00 209F FFFF 1M Reserved Reserved Reserved 00 20A0 0000 00 20A3 FFFF 256K Reserved Reserved Reserved 00 20A4 0000 00 20A4 FFFF 64K Reserved Reserved Reserved 00 20A5 0000 00 20AF FFFF 704K Reserved Reserved Reserved 00 20B0 0000 00 20B3 FFFF 256K Boot ROM Boot ROM Boot ROM 00 20B4 0000 00 20BE FFFF 704K Reserved Reserved Reserved 00 20BF 0000 00 20BF 01FF 64K Reserved Reserved Reserved 00 20C0 0000 00 20FF FFFF 4M Reserved Reserved Reserved 00 2100 0000 00 2100 03FF 1K Reserved Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 77 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 2100 0400 00 2100 05FF 512 SPI0 SPI0 SPI0 00 2100 0600 00 2100 07FF 512 SPI1 SPI1 SPI1 00 2100 0800 00 2100 09FF 512 SPI2 SPI2 SPI2 00 2100 0A00 00 2100 0AFF 256 EMIF Config EMIF Config EMIF Config 00 2100 0B00 00 2100 FFFF 62K-768 Reserved Reserved Reserved 00 2101 0000 00 2101 01FF 512 DDR3A EMIF Config DDR3A EMIF Config DDR3A EMIF Config 00 2101 0200 00 2101 07FF 2K-512 Reserved Reserved Reserved 00 2101 0800 00 2101 09FF 512 Reserved Reserved Reserved 00 2101 0A00 00 2101 0FFF 2K-512 Reserved Reserved Reserved 00 2101 1000 00 2101 FFFF 60K Reserved Reserved Reserved 00 2102 0000 00 2103 FFFF 128K DDR3B EMIF configuration DDR3B EMIF configuration DDR3B EMIF configuration 00 2104 0000 00 217F FFFF 4M-256K Reserved Reserved Reserved 00 2140 0000 00 2140 00FF 256 HyperLink0 config HyperLink0 config HyperLink0 config 00 2140 0100 00 2140 01FF 256 HyperLink1 config HyperLink1 config HyperLink1 config 00 2140 0400 00 217F FFFF 4M-512 Reserved Reserved Reserved 00 2180 0000 00 2180 7FFF 32K PCIe config PCIe config PCIe config 00 2180 8000 00 21BF FFFF 4M-32K Reserved Reserved Reserved 00 21C0 0000 00 21FF FFFF 4M Reserved Reserved Reserved 00 2200 0000 00 229F FFFF 10M Reserved Reserved Reserved 00 22A0 0000 00 22A0 FFFF 64K Reserved Reserved Reserved 00 22A1 0000 00 22AF FFFF 1M-64K Reserved Reserved Reserved 00 22B0 0000 00 22B0 FFFF 64K Reserved Reserved Reserved 00 22B1 0000 00 22BF FFFF 1M-64K Reserved Reserved Reserved 00 22C0 0000 00 22C0 FFFF 64K Reserved Reserved Reserved 00 22C1 0000 00 22CF FFFF 1M-64K Reserved Reserved Reserved 00 22D0 0000 00 22D0 FFFF 64K Reserved Reserved Reserved 00 22D1 0000 00 22DF FFFF 1M-64K Reserved Reserved Reserved 00 22E0 0000 00 22E0 FFFF 64K Reserved Reserved Reserved 00 22E1 0000 00 22EF FFFF 1M-64K Reserved Reserved Reserved 00 22F0 0000 00 22F0 FFFF 64K Reserved Reserved Reserved 00 22F1 0000 00 22FF FFFF 1M-64K Reserved Reserved Reserved 00 2300 0000 00 2300 FFFF 64K Reserved Reserved Reserved 00 2301 0000 00 230F FFFF 1M-64K Reserved Reserved Reserved 00 2310 0000 00 2310 FFFF 64K Reserved Reserved Reserved 00 2311 0000 00 231F FFFF 1M-64K Reserved Reserved Reserved 00 2320 0000 00 2324 FFFF 384K Reserved Reserved Reserved 00 2325 0000 00 239F FFFF 8M-384K Reserved Reserved Reserved 00 23A0 0000 00 23BF FFFF 2M Navigator Navigator Navigator 00 23C0 0000 00 23FF FFFF 4M Reserved Reserved Reserved 00 2400 0000 00 27FF FFFF 64M Reserved Reserved Reserved 00 2800 0000 00 2FFF FFFF 128M HyperLink1 data HyperLink1 data HyperLink1 data 00 3000 0000 00 33FF FFFF 64M EMIF16 CE0 EMIF16 CE0 EMIF16 CE0 00 3400 0000 00 37FF FFFF 64M EMIF16 CE1 EMIF16 CE1 EMIF16 CE1 00 3800 0000 00 3BFF FFFF 64M EMIF16 CE2 EMIF16 CE2 EMIF16 CE2 00 3C00 0000 00 3FFF FFFF 64M EMIF16 CE3 EMIF16 CE3 EMIF16 CE3 00 4000 0000 00 4FFF FFFF 256M HyperLink0 data HyperLink0 data HyperLink0 data 00 5000 0000 00 5FFF FFFF 256M PCIe data PCIe data PCIe data 78 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-1. Device Memory Map Summary for 66AK2Hxx (continued) PHYSICAL 40-BIT ADDRESS START END BYTES ARM VIEW DSP VIEW SOC VIEW 00 6000 0000 00 7FFF FFFF 512M DDR3B data (2) (3) DDR3B data (4) DDR3B data 00 8000 0000 00 FFFF FFFF 2G DDR3A data/DDR3B data (2) (5) DDR3B data DDR3A data (6) 01 0000 0000 01 2100 FFFF 528M+64 K Reserved Reserved Reserved 01 2101 0000 01 2101 01FF 512 DDR3A EMIF configuration (7) DDR3A EMIF configuration (8) DDR3A EMIF configuration (9) 01 2101 0200 07 FFFF FFFF 32G-512 Reserved Reserved Reserved 08 0000 0000 09 FFFF FFFF 8G DDR3A data DDR3A data (8) DDR3A data (9) 0A 0000 0000 FF FFFF FFFF 984G Reserved Reserved Reserved (2) (3) (4) (5) (6) (7) (8) (9) 8.2 No IO coherency supported for this region (see the KeyStone II Architecture ARM CorePac User's Guide). This region is mapped to DDR3B. It is aliased of 00 8000 0000 to 00 9FFF FFFF (the first 512MB of DDR3B) if the state of DDR3A_REMAP_EN pin at boot time is ‘0’. This region is aliased of 00 8000 0000 to 00 9FFF FFFF (the first 512MB of DDR3B). This region is mapped to DDR3A or DDR3B depending on the state of DDR3A_REMAP_EN pin at boot time. If the pin is ‘1’, this region is mapped to the first 2GB of DDR3A which is aliased of 08 0000 0000 to 08 7FFF FFFF. If the pin is ‘0’, this region is mapped as 2GB of DDR3B. MPAX from SES port extends the address to this region. This region is aliased to 00 2101 0000-00 2101 01FF. Access to 40-bit address requires XMC MPAX programmation. Access to 40-bit address requires MSMC MPAX programmation. MPAX from SES port need to remap the region of 00 2101 0000-00 2101 01FF to this region. Memory Protection Unit (MPU) for 66AK2Hxx CFG (configuration) space of all slave devices on the TeraNet is protected by the MPU. The 66AK2Hxx contains 15 MPUs: • MPU0 is used for main TeraNet_3P_B (SCR_3P (B)) CFG. • MPU1/2/5 are used for QM_SS (one for VBUSM port and one each for the two configuration VBUSP ports). • MPU3/4/6 are reserved. • MPU7 is used for DDR3_B. • MPU8 is used for EMIF16. • MPU9 is used for interrupt controllers connected to TeraNet_3P (SCR_3P). • MPU10 is used for semaphore. • MPU11 is used to protect TeraNet_6P_B (SCR_6P (B)) CPU/6 CFG TeraNet. • MPU12/13/14 are used for SPI0/1/2. This section contains MPU register map and details of device-specific MPU registers only. For MPU features and details of generic MPU registers, see the KeyStone Architecture Memory Protection Unit (MPU) User's Guide. Table 8-2, Table 8-3, and Table 8-4 show the configuration of each MPU and the memory regions protected by each MPU. Table 8-2. MPU0-MPU5 Default Configuration MPU0 MAIN SCR_3P (B) MPU1 (QM_SS DATA PORT) MPU2 (QM_SS CFG1 PORT) MPU3 MPU4 Default permission Assume allowed Assume allowed Assume allowed Reserved Reserved Number of allowed IDs supported 16 16 16 16 Number of programmable 16 ranges supported 16 16 16 1KB granularity 1KB granularity SETTING Compare width 1KB granularity 1KB granularity MPU5 (QM_SS CFG2 PORT) Assume allowed Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 79 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-3. MPU6-MPU11 Default Configuration SETTING MPU6 MPU7 DDR3B MPU8 EMIF16 MPU9 INTC MPU10 SM MPU11 SCR_6P (B) Default permission Reserved Assume allowed Assume allowed Assume allowed Assume allowed Assume allowed Number of allowed IDs supported 16 16 16 16 16 Number of programmable ranges supported 16 8 4 2 16 Compare width 1KB granularity 1KB granularity 1KB granularity 1KB granularity 1KB granularity Table 8-4. MPU12-MPU14 Default Configuration SETTING MPU12 SPI0 MPU13 SPI1 MPU14 SPI2 Default permission Assume allowed Assume allowed Assume allowed Number of allowed IDs supported 16 16 16 Number of programmable ranges supported 2 2 2 Compare width 1KB granularity 1KB granularity 1KB granularity Table 8-5. MPU Memory Regions MEMORY PROTECTION START ADDRESS END ADDRESS MPU0 Main CFG SCR 0x01D0_0000 0x01E7_FFFF MPU1 QM_SS DATA PORT 0x23A0_0000 0x23BF_FFFF MPU2 QM_SS CFG1 PORT 0x02A0_0000 0x02AF_FFFF MPU3 Reserved 0x027C_0000 0x027C_03FF MPU4 Reserved 0x0210_0000 0x0215_FFFF MPU5 QM_SS CFG2 PORT 0x02A0_4000 0x02BF_FFFF MPU6 Reserved 0x02C0_0000 0x02CD_FFFF MPU7 DDR3B 0x2101_0000 0xFFFF_FFFF MPU8 SPIROM/EMIF16 0x20B0_0000 0x3FFF_FFFF MPU9 INTC/AINTC 0x0264_0000 0x0264_07FF MPU10 Semaphore 0x0260_0000 0x0260_9FFF MPU11 SCR_6 and CPU/6 CFG SCR 0x0220_0000 0x03FF_FFFF MPU12 SPI0 0x2100_0400 0x2100_07FF MPU13 SPI1 0x2100_0400 0x2100_07FF MPU14 SPI2 0x2100_0800 0x2100_0AFF 80 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-6 shows the unique Master ID assigned to each CorePac and peripherals on the device. Table 8-6. Master ID Settings MASTER ID 66AK2H12/14 66AK2H06 0 C66x CorePac0 Data 1 C66x CorePac1 Data 2 C66x CorePac2 Data 3 C66x CorePac3 Data 4 C66x CorePac4 Data Reserved 5 C66x CorePac5 Data Reserved 6 C66x CorePac6 Data Reserved 7 C66x CorePac7 Data Reserved 8 ARM CorePac 0 noncache accesses and cache accesses for all ARM cores 9 ARM CorePac 1 noncache accesses 10 ARM CorePac 2 noncache accesses 11 ARM CorePac 3 noncache accesses Reserved Reserved 12 Reserved 13 Reserved 14 Reserved 15 Reserved 16 C66x CorePac0 CFG 17 C66x CorePac1 CFG 18 C66x CorePac2 CFG 19 C66x CorePac3 CFG 20 C66x CorePac4 CFG Reserved 21 C66x CorePac5 CFG Reserved 22 C66x CorePac6 CFG Reserved 23 C66x CorePac7 CFG Reserved 24 Reserved 25 EDMA0_TC0 read 26 EDMA0_TC0 write 27 EDMA0_TC1 read 28 Hyperlink0 29 Hyperlink1 30 SRIO 31 PCIE 32 EDMA0_TC1 write 33 EDMA1_TC0 read 34 EDMA1_TC0 write 35 EDMA1_TC1 read 36 EDMA1_TC1write 37 EDMA1_TC2 read 38 EDMA1_TC2 write 39 EDMA1_TC3 read 40 EDMA1_TC3 write 41 EDMA2_TC0 read 42 EDMA2_TC0 write 43 EDMA2_TC1 read 44 EDMA2_TC1 write Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 81 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-6. Master ID Settings (continued) MASTER ID 66AK2H12/14 66AK2H06 45 EDMA2_TC2 read 46 EDMA2_TC2 write 47 EDMA2_TC3 read 48 EDMA2_TC3 write 49 EDMA3_TC0 read 50 EDMA3_TC0 write 51 EDMA3_TC1 read 52 MSMC (1) 53 EDMA3_TC1 write 54 to 55 SRIO PKTDMA 56 Reserved 57 Reserved 58 Reserved 59 Reserved 60 Reserved 61 Reserved 62 EDMA3CC0 63 EDMA3CC1 64 EDMA3CC2 65 Reserved 66 Reserved 67 Reserved 68 to 71 Queue Manager 72 to 79 Reserved 80 Reserved 81 Reserved 82 Reserved 83 EDMA3_CC_TR 84 to 87 10GbE (66AK2H14 only) 88 to 91 Reserved 92 to 95 Packet Coprocessor MST2 96 to 99 Packet Coprocessor MST1 100 to 101 Reserved 102 Reserved 103 Reserved 104 Reserved 105 Reserved 106 Reserved 107 DBG_DAP 108-139 Reserved 140 CPT_L2_0 141 CPT_L2_1 142 CPT_L2_2 143 CPT_L2_3 144 CPT_L2_4 145 CPT_L2_5 (1) 82 The master ID for MSMC is for the transaction initiated by MSMC internally and sent to the DDR. Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-6. Master ID Settings (continued) MASTER ID 66AK2H12/14 66AK2H06 146 CPT_L2_6 147 CPT_L2_7 148 CPT_MSMC0 149 CPT_MSMC1 150 CPT_MSMC2 151 CPT_MSMC3 152 CPT_DDR3A 153 CPT_SM 154 CPT_QM_CFG1 155 CPT_QM_M 156 CPT_CFG 157 Reserved 158 Reserved 159 Reserved 160 CPT_QM_CFG2 161 CPT_DDR3B 162 Reserved 163 Reserved 164 CPT_EDMA3CC0_4 165 CPT_EDMA3CC1_2_3 166 CPT_INTC 167 CPT_SPI_ROM_EMIP16 168 USB 169 EDMA4_TC0 read 170 EDMA4_TC0 write 171 EDMA4_TC1 read 172 EDMA4_TC1 write 173 EDMA4_CC_TR 174 CPT_MSMC5 175 CPT_MSMC6 176 CPT_MSMC7 177 CPT_MSMC4 178 Reserved 179 Reserved 180-183 NETCP 184-255 Reserved NOTE There are two master ID values assigned to the Queue Manager_second master port, one master ID for external linking RAM and the other one for the PDSP/MCDM accesses. Table 8-7 shows the privilege ID of each C66x CorePac and every mastering peripheral. The table also shows the privilege level (supervisor vs. user), security level (secure vs. nonsecure), and access type (instruction read vs. data/DMA read or write) of each master on the device. In some cases, a particular setting depends on software being executed at the time of the access or the configuration of the master peripheral. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 83 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-7. Privilege ID Settings PRIVILEGE ID MASTER PRIVILEGE LEVEL SECURITY LEVEL ACCESS TYPE 0 C66x CorePac0 SW dependant, driven by MSMC Nonsecure DMA 1 C66x CorePac1 SW dependant, driven by MSMC Nonsecure DMA 2 C66x CorePac2 SW dependant, driven by MSMC Nonsecure DMA 3 C66x CorePac3 SW dependant, driven by MSMC Nonsecure DMA 4 C66x CorePac4 SW dependant, driven by MSMC Nonsecure DMA 5 C66x CorePac5 SW dependant, driven by MSMC Nonsecure DMA 6 C66x CorePac6 SW dependant, driven by MSMC Nonsecure DMA 7 C66x CorePac7 SW dependant, driven by MSMC Nonsecure DMA 8 ARM CorePac SW dependent Nonsecure DMA 9 SRIO_M and all Packet DMA masters (NetCP, Both QM_CDMA, SRIO_CDMA, 10GbE (1)), USB User/driven by SRIO block, user mode and supervisor mode is determined by per transaction basis. Only the transaction with source ID matching the value in SupervisorID register is granted supervisor mode. Nonsecure DMA 10 QM_Second (2) User Nonsecure DMA 11 PCIe Supervisor Nonsecure DMA 12 DAP Driven by Emulation SW Nonsecure DMA 13 Reserved 14 HyperLink Supervisor Nonsecure DMA 15 (1) (2) Reserved 66AK2H14 only. QM_Second provides a path that PDSP uses to access the system memory. 8.2.1 MPU Registers This section includes the offsets for MPU registers and definitions for device-specific MPU registers. For Number of Programmable Ranges supported (PROGx_MPSA, PROGxMPEA) refer to the following tables. 8.2.1.1 MPU Register Map Table 8-8. MPU Registers OFFSET NAME DESCRIPTION 0h REVID Revision ID 4h CONFIG Configuration 10h IRAWSTAT Interrupt raw status/set 14h IENSTAT Interrupt enable status/clear 18h IENSET Interrupt enable 1Ch IENCLR Interrupt enable clear 20h EOI End of interrupt 200h PROG0_MPSAR Programmable range 0, start address 204h PROG0_MPEAR Programmable range 0, end address 208h PROG0_MPPAR Programmable range 0, memory page protection attributes 210h PROG1_MPSAR Programmable range 1, start address 214h PROG1_MPEAR Programmable range 1, end address 218h PROG1_MPPAR Programmable range 1, memory page protection attributes 220h PROG2_MPSAR Programmable range 2, start address 224h PROG2_MPEAR Programmable range 2, end address 228h PROG2_MPPAR Programmable range 2, memory page protection attributes 230h PROG3_MPSAR Programmable range 3, start address 84 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-8. MPU Registers (continued) OFFSET NAME DESCRIPTION 234h PROG3_MPEAR Programmable range 3, end address 238h PROG3_MPPAR Programmable range 3, memory page protection attributes 240h PROG4_MPSAR Programmable range 4, start address 244h PROG4_MPEAR Programmable range 4, end address 248h PROG4_MPPAR Programmable range 4, memory page protection attributes 250h PROG5_MPSAR Programmable range 5, start address 254h PROG5_MPEAR Programmable range 5, end address 258h PROG5_MPPAR Programmable range 5, memory page protection attributes 260h PROG6_MPSAR Programmable range 6, start address 264h PROG6_MPEAR Programmable range 6, end address 268h PROG6_MPPAR Programmable range 6, memory page protection attributes 270h PROG7_MPSAR Programmable range 7, start address 274h PROG7_MPEAR Programmable range 7, end address 278h PROG7_MPPAR Programmable range 7, memory page protection attributes 280h PROG8_MPSAR Programmable range 8, start address 284h PROG8_MPEAR Programmable range 8, end address 288h PROG8_MPPAR Programmable range 8, memory page protection attributes 290h PROG9_MPSAR Programmable range 9, start address 294h PROG9_MPEAR Programmable range 9, end address 298h PROG9_MPPAR Programmable range 9, memory page protection attributes 2A0h PROG10_MPSAR Programmable range 10, start address 2A4h PROG10_MPEAR Programmable range 10, end address 2A8h PROG10_MPPAR Programmable range 10, memory page protection attributes 2B0h PROG11_MPSAR Programmable range 11, start address 2B4h PROG11_MPEAR Programmable range 11, end address 2B8h PROG11_MPPAR Programmable range 11, memory page protection attributes 2C0h PROG12_MPSAR Programmable range 12, start address 2C4h PROG12_MPEAR Programmable range 12, end address 2C8h PROG12_MPPAR Programmable range 12, memory page protection attributes 2D0h PROG13_MPSAR Programmable range 13, start address 2D4h PROG13_MPEAR Programmable range 13, end address 2Dh PROG13_MPPAR Programmable range 13, memory page protection attributes 2E0h PROG14_MPSAR Programmable range 14, start address 2E4h PROG14_MPEAR Programmable range 14, end address 2E8h PROG14_MPPAR Programmable range 14, memory page protection attributes 2F0h PROG15_MPSAR Programmable range 15, start address 2F4h PROG15_MPEAR Programmable range 15, end address 2F8h PROG15_MPPAR Programmable range 15, memory page protection attributes 300h FLTADDRR Fault address 304h FLTSTAT Fault status 308h FLTCLR Fault clear Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 85 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 8.2.1.2 www.ti.com Device-Specific MPU Registers 8.2.1.2.1 Configuration Register (CONFIG) The configuration register (CONFIG) contains the configuration value of the MPU as described in Table 89. Table 8-9. Configuration Register Field Descriptions Bits Field Description 31-24 ADDR_WIDTH Address alignment for range checking • 0 = 1KB alignment • 6 = 64KB alignment 23-20 NUM_FIXED Number of fixed address ranges 19-16 NUM_PROG Number of programmable address ranges 15-12 NUM_AIDS Number of supported AIDs 11-1 Reserved Reserved. Always read as 0. 0 ASSUME_ALLOWED Assume allowed bit. When an address is not covered by any MPU protection range, this bit determines whether the transfer is assumed to be allowed or not. • 0 = Assume disallowed • 1 = Assume allowed 8.2.2 MPU Programmable Range Registers 8.2.2.1 Programmable Range n Start Address Register (PROGn_MPSAR) The Programmable Address Start Register holds the start address for the range. This register is writeable by a supervisor entity only. If NS = 0 (nonsecure mode) in the associated MPPAR register, then the register is also writeable only by a secure entity. The start address must be aligned on a page boundary. The size of the page is 1KB. The size of the page determines the width of the address field in MPSAR and MPEAR. The PROGn_MPSAR register is shown in Figure 8-1 and described in Table 8-10. The reset values are listed in Table 8-11 for MPU0-MPU5, Table 8-12 for MPU6-MPU11, and Table 8-13 for MPU12-MPU14. Figure 8-1. Programmable Range n Start Address Register (PROGn_MPSAR) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 START_ADDR Reserved R/W R 3 2 1 0 Legend: R = Read only; R/W = Read/Write Table 8-10. Programmable Range n Start Address Register Field Descriptions Bit Field Description 31-10 START_ADDR Start address for range n 9-0 Reserved Reserved. Always read as 0. Table 8-11. MPU0-MPU5 Programmable Range n Start Address Register (PROGn_MPSAR) Reset Values REGISTER MPU0 MPU1 MPU2 MPU3 MPU4 MPU5 PROG0_MPSAR 0x01D0_0000 0x23A0_0000 0x02A0_0000 Reserved Reserved 0x02A0_4000 PROG1_MPSAR 0x01F0_0000 0x23A0_2000 0x02A0_2000 Reserved Reserved 0x02A0_5000 PROG2_MPSAR 0x02F0_0000 0x023A_6000 0x02A0_6000 Reserved Reserved 0x02A0_6400 PROG3_MPSAR 0x0200_0000 0x23A0_6800 0x02A0_6800 Reserved Reserved 0x02A0_7400 PROG4_MPSAR 0x020C_0000 0x23A0_7000 0x02A0_7000 Reserved Reserved 0x02A0_A000 PROG5_MPSAR 0x021C_0000 0x23A0_8000 0x02A0_8000 Reserved Reserved 0x02A0_D000 PROG6_MPSAR 0x021D_0000 0x23A0_C000 0x02A0_C000 Reserved Reserved 0x02A0_E000 86 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-11. MPU0-MPU5 Programmable Range n Start Address Register (PROGn_MPSAR) Reset Values (continued) REGISTER MPU0 MPU1 MPU2 MPU3 MPU4 MPU5 PROG7_MPSAR 0x021F_0000 0x23A0_E000 0x02A0_E000 Reserved Reserved 0x02A0_F000 PROG8_MPSAR 0x0234_0000 0x23A0_F000 0x02A0_F000 Reserved Reserved 0x02A0_F800 PROG9_MPSAR 0x0254_0000 0x23A0_F800 0x02A0_F800 Reserved Reserved 0x02A1_2000 PROG10_MPSAR 0x0258_0000 0x23A1_0000 0x02A1_0000 Reserved Reserved 0x02A1_C000 PROG11_MPSAR 0x0000_0000 0x23A1_C000 0x02A2_0000 Reserved Reserved 0x02A2_8000 PROG12_MPSAR 0x0290_0000 0x23A4_0000 0x02A4_0000 Reserved Reserved 0x02A6_0000 PROG13_MPSAR 0x01E8_0000 0x23A8_0000 0x02A8_0000 Reserved Reserved 0x02AA_0000 PROG14_MPSAR 0x01E8_0800 0x23B0_0000 0x02AC_0000 Reserved Reserved 0x02B0_0000 PROG15_MPSAR 0x01E0_0000 0x23B8_0000 0x02AE_0000 Reserved Reserved 0x02B8_0000 Table 8-12. MPU6-MPU11 Programmable Range n Start Address Register (PROGn_MPSAR) Reset Values REGISTER MPU6 MPU7 MPU8 MPU9 MPU10 MPU11 PROG0_MPSAR Reserved 0x2101_0000 0x3000_0000 0x0260_0000 0x0264_0000 0x0220_0000 PROG1_MPSAR Reserved 0x0000_0000 0x3200_0000 0x0260_4000 0x0000_0000 0x0231_0000 PROG2_MPSAR Reserved 0x0800_0000 0x3400_0000 0x0260_8000 N/A 0x0231_A000 PROG3_MPSAR Reserved 0x1000_0000 0x3600_0000 0x0256_0000 N/A 0x0233_0000 PROG4_MPSAR Reserved 0x1800_0000 0x3800_0000 0x0000_0000 N/A 0x0235_0000 PROG5_MPSAR Reserved 0x2000_0000 0x3A00_0000 0x0000_0000 N/A 0x0263_0000 PROG6_MPSAR Reserved 0x2800_0000 0x3C00_0000 0x0000_0000 N/A 0x0244_0000 PROG7_MPSAR Reserved 0x3000_0000 0x2100_0800 0x0000_0000 N/A 0x024C_0000 PROG8_MPSAR Reserved 0x3800_0000 N/A 0x0000_0000 N/A 0x0250_0000 PROG9_MPSAR Reserved 0x4000_0000 N/A 0x0000_0000 N/A 0x0253_0000 PROG10_MPSAR Reserved 0x4800_0000 N/A 0x0000_0000 N/A 0x0253_0C00 PROG11_MPSAR Reserved 0x5000_0000 N/A 0x0000_0000 N/A 0x0260_B000 PROG12_MPSAR Reserved 0x5800_0000 N/A 0x0000_0000 N/A 0x0262_0000 PROG13_MPSAR Reserved 0x6000_0000 N/A 0x0000_0000 N/A 0x0300_0000 PROG14_MPSAR Reserved 0x6800_0000 N/A 0x0000_0000 N/A 0x021E_0000 PROG15_MPSAR Reserved 0x7000_0000 N/A 0x0000_0000 N/A 0x0268_0000 Table 8-13. MPU12-MPU14 Programmable Range n Start Address Register (PROGn_MPSAR) Reset Values REGISTER MPU12 MPU13 MPU14 PROG0_MPSAR 0x2100_0400 0x2100_0400 0x2100_0800 PROG1_MPSAR 0x0000_0000 0x0000_0000 0x0000_0000 PROG2_MPSAR N/A N/A N/A PROG3_MPSAR N/A N/A N/A PROG4_MPSAR N/A N/A N/A PROG5_MPSAR N/A N/A N/A PROG6_MPSAR N/A N/A N/A PROG7_MPSAR N/A N/A N/A PROG8_MPSAR N/A N/A N/A PROG9_MPSAR N/A N/A N/A PROG10_MPSAR N/A N/A N/A PROG11_MPSAR N/A N/A N/A PROG12_MPSAR N/A N/A N/A PROG13_MPSAR N/A N/A N/A Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 87 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-13. MPU12-MPU14 Programmable Range n Start Address Register (PROGn_MPSAR) Reset Values (continued) REGISTER MPU12 MPU13 MPU14 PROG14_MPSAR N/A N/A N/A PROG15_MPSAR N/A N/A N/A 8.2.2.2 Programmable Range n - End Address Register (PROGn_MPEAR) The programmable address end register holds the end address for the range. This register is writeable by a supervisor entity only. If NS = 0 (nonsecure mode) in the associated MPPAR register then the register is also writeable only by a secure entity. The end address must be aligned on a page boundary. The size of the page depends on the MPU number. The page size for MPU1 is 1KB and for MPU2 it is 64KB. The size of the page determines the width of the address field in MPSAR and MPEAR. The PROGn_MPEAR register is shown in Figure 8-2 and described in Table 8-14. The reset values are listed in Table 8-15 for MPU0-MPU5, Table 8-16 for MPU6-MPU11, and Table 8-17 for MPU12-MPU14. Figure 8-2. Programmable Range n End Address Register (PROGn_MPEAR) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 END_ADDR Reserved R/W R 3 2 1 0 Legend: R = Read only; R/W = Read/Write Table 8-14. Programmable Range n End Address Register Field Descriptions Bit Field Description 31-10 END_ADDR End address for range n 9-0 Reserved Reserved. Always read as 3FFh. Table 8-15. MPU0-MPU5 Programmable Range n End Address Register (PROGn_MPEAR) Reset Values REGISTER MPU0 MPU1 MPU2 MPU3 MPU4 MPU5 PROG0_MPEAR 0x01DF_FFFF 0x23A0_1FFF 0x02A0_00FF Reserved Reserved 0x02A0_4FFF PROG1_MPEAR 0x01F7_FFFF 0x23A0_5FFF 0x02A0_3FFF Reserved Reserved 0x02A0_5FFF PROG2_MPEAR 0x02FF_FFFF 0x23A0_67FF 0x02A0_63FF Reserved Reserved 0x02A0_67FF PROG3_MPEAR 0x020B_FFFF 0x23A0_6FFF 0x02A0_6FFF Reserved Reserved 0x02A0_7FFF PROG4_MPEAR 0x020F_FFFF 0x23A0_7FFF 0x02A0_73FF Reserved Reserved 0x02A0_BFFF PROG5_MPEAR 0x021C_83FF 0x23A0_BFFF 0x02A0_9FFF Reserved Reserved 0x02A0_DFFF PROG6_MPEAR 0x021D_C0FF 0x23A0_DFFF 0x02A0_CFFF Reserved Reserved 0x02A0_E7FF PROG7_MPEAR 0x021F_C7FF 0x23A0_EFFF 0x02A0_E7FF Reserved Reserved 0x02A0_F7FF PROG8_MPEAR 0x0234_C0FF 0x23A0_F7FF 0x02A0_F7FF Reserved Reserved 0x02A0_FFFF PROG9_MPEAR 0x0255_FFFF 0x23A0_FFFF 0x02A0_FFFF Reserved Reserved 0x02A1_7FFF PROG10_MPEAR 0x025F_FFFF 0x23A1_BFFF 0x02A1_1FFF Reserved Reserved 0x02A1_FFFF PROG11_MPEAR 0x0000_0000 0x23A3_FFFF 0x02A2_5FFF Reserved Reserved 0x02A3_FFFF PROG12_MPEAR 0x029F_FFFF 0x23A7_FFFF 0x02A5_FFFF Reserved Reserved 0x02A7_FFFF PROG13_MPEAR 0x01E8_07FF 0x23AF_FFFF 0x02A9_FFFF Reserved Reserved 0x02AB_FFFF PROG14_MPEAR 0x01E8_43FF 0x23B7_FFFF 0x02AD_FFFF Reserved Reserved 0x02B7_FFFF PROG15_MPEAR 0x01E7_FFFF 0x23BF_FFFF 0x02AF_FFFF Reserved Reserved 0x02BF_FFFF 88 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-16. MPU6-MPU11 Programmable Range n End Address Register (PROGn_MPEAR) Reset Values REGISTER MPU6 MPU7 MPU8 MPU9 MPU10 MPU11 PROG0_MPEAR Reserved 0x2103_FFFF 0x31FF_FFFF 0x0260_1FFF 0x0264_07FF 0x022F_027F PROG1_MPEAR Reserved 0x07FF_FFFF 0x33FF_FFFF 0x0260_5FFF 0x0000_0000 0x0231_01FF PROG2_MPEAR Reserved 0x0FFF_FFFF 0x35FF_FFFF 0x0260_9FFF N/A 0x0232_FFFF PROG3_MPEAR Reserved 0x17FF_FFFF 0x37FF_FFFF 0x0257_FFFF N/A 0x0233_07FF PROG4_MPEAR Reserved 0x1FFF_FFFF 0x39FF_FFFF Reserved N/A 0x0235_0FFF PROG5_MPEAR Reserved 0x27FF_FFFF 0x3BFF_FFFF Reserved N/A 0x0263_FFFF PROG6_MPEAR Reserved 0x2FFF_FFFF 0x3FFF_FFFF Reserved N/A 0x024B_3FFF PROG7_MPEAR Reserved 0x37FF_FFFF 0x2100_0AFF Reserved N/A 0x024C_0BFF PROG8_MPEAR Reserved 0x3FFF_FFFF N/A Reserved N/A 0x0250_7FFF PROG9_MPEAR Reserved 0x47FF_FFFF N/A Reserved N/A 0x0253_0BFF PROG10_MPEAR Reserved 0x4FFF_FFFF N/A Reserved N/A 0x0253_FFFF PROG11_MPEAR Reserved 0x57FF_FFFF N/A Reserved N/A 0x0260_BFFF PROG12_MPEAR Reserved 0x5FFF_FFFF N/A Reserved N/A 0x0262_0FFF PROG13_MPEAR Reserved 0x67FF_FFFF N/A Reserved N/A 0x03FF_FFFF PROG14_MPEAR Reserved 0x6FFF_FFFF N/A Reserved N/A 0x021E_1FFF PROG15_MPEAR Reserved 0x7FFF_FFFF N/A Reserved N/A 0x026F_FFFF Table 8-17. MPU12-MPU14 Programmable Range n End Address Register (PROGn_MPEAR) Reset Values REGISTER MPU12 MPU13 MPU14 PROG0_MPEAR 0x2100_07FF 0x2100_07FF 0x2100_0AFF PROG1_MPEAR 0x0000_0000 0x0000_0000 0x0000_0000 PROG2_MPEAR N/A N/A N/A PROG3_MPEAR N/A N/A N/A PROG4_MPEAR N/A N/A N/A PROG5_MPEAR N/A N/A N/A PROG6_MPEAR N/A N/A N/A PROG7_MPEAR N/A N/A N/A PROG8_MPEAR N/A N/A N/A PROG9_MPEAR N/A N/A N/A PROG10_MPEAR N/A N/A N/A PROG11_MPEAR N/A N/A N/A PROG12_MPEAR N/A N/A N/A PROG13_MPEAR N/A N/A N/A PROG14_MPEAR N/A N/A N/A PROG15_MPEAR N/A N/A N/A 8.2.2.3 Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) The programmable address memory protection page attribute register holds the permissions for the region. This register is writeable only by a nondebug supervisor entity. If NS = 0 (secure mode) then the register is also writeable only by a nondebug secure entity. The NS bit is writeable only by a nondebug secure entity. For debug accesses, the register is writeable only when NS = 1 or EMU = 1. The PROGn_MPPAR register is shown in Figure 8-3 and described in Table 8-18. The reset values are listed in Table 8-19 for MPU0-MPU5, Table 8-20 for MPU6-MPU11, and Table 8-21 for MPU12-MPU14. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 89 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Figure 8-3. Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) 31 30 29 25 24 23 22 21 20 19 18 17 16 Reserved 28 27 26 AID15 AID14 AID13 AID12 AID11 AID10 AID9 AID8 AID7 AID6 R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 AID5 AID4 AID3 AID2 AID1 AID0 AIDX Rsvd NS EMU SR SW SX UR UW UX R/W R/W R/W R/W R/W R/W R/W R R/W R/W R/W R/W R/W R/W R/W R/W Table 8-18. Programmable Range n Memory Protection Page Attribute Register Field Descriptions Bits Name Description 31-26 Reserved Reserved. Always read as 0. 25 AID15 Controls access from ID = 15 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 24 AID14 Controls access from ID = 14 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 23 AID13 Controls access from ID = 13 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 22 AID12 Controls access from ID = 12 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 21 AID11 Controls access from ID = 11 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 20 AID10 Controls access from ID = 10 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 19 AID9 Controls access from ID = 9 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 18 AID8 Controls access from ID = 8 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 17 AID7 Controls access from ID = 7 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 16 AID6 Controls access from ID = 6 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 15 AID5 Controls access from ID = 5 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 14 AID4 Controls access from ID = 4 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 13 AID3 Controls access from ID = 3 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 12 AID2 Controls access from ID = 2 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 90 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-18. Programmable Range n Memory Protection Page Attribute Register Field Descriptions (continued) Bits Name Description 11 AID1 Controls access from ID = 1 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 10 AID0 Controls access from ID = 0 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 9 AIDX Controls access from ID > 15 • 0 = Access is not checked for permissions • 1 = Access is checked for permissions 8 Reserved Reserved. Always reads as 0. 7 NS Nonsecure access permission • 0 = Only secure access allowed • 1 = Nonsecure access allowed 6 EMU Emulation (debug) access permission. This bit is ignored if NS = 1 • 0 = Debug access not allowed • 1 = Debug access allowed 5 SR Supervisor Read permission • 0 = Access not allowed • 1 = Access allowed 4 SW Supervisor Write permission • 0 = Access not allowed • 1 = Access allowed 3 SX Supervisor Execute permission • 0 = Access not allowed • 1 = Access allowed 2 UR User Read permission • 0 = Access not allowed • 1 = Access allowed 1 UW User Write permission • 0 = Access not allowed • 1 = Access allowed 0 UX User Execute permission • 0 = Access not allowed • 1 = Access allowed Table 8-19. MPU0-MPU5 Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) Reset Values Register MPU0 MPU1 MPU2 MPU3 MPU4 MPU5 PROG0_MPPAR 0x03FF_FCB6 0x03FF_FCB6 0x03FF_FCB6 Reserved Reserved 0x03FF_FCB4 PROG1_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCB4 PROG2_MPPAR 0x03FF_FCB6 0x03FF_FCA4 0x03FF_FCA4 Reserved Reserved 0x03FF_FCA4 PROG3_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCF4 PROG4_MPPAR 0x03FF_FCB6 0x03FF_FCF4 0x03FF_FCF4 Reserved Reserved 0x03FF_FCB4 PROG5_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCB4 PROG6_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCB4 PROG7_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCB4 PROG8_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCF4 PROG9_MPPAR 0x03FF_FCB6 0x03FF_FCF4 0x03FF_FCF4 Reserved Reserved 0x03FF_FCB4 PROG10_MPPAR 0x03FF_FCB6 0x03FF_FCB4 0x03FF_FCB4 Reserved Reserved 0x03FF_FCF4 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 91 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-19. MPU0-MPU5 Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) Reset Values (continued) Register MPU0 MPU1 MPU2 MPU3 MPU4 MPU5 PROG11_MPPAR 0x03FF_FCB6 0x03FF_FCF4 0x03FF_FCF4 Reserved Reserved 0x03FF_FCF4 PROG12_MPPAR 0x03FF_FCB4 0x03FF_FCA4 0x03FF_FCA4 Reserved Reserved 0x03FF_FCA4 PROG13_MPPAR 0x03FF_FCB6 0x03FF_FCB6 0x03FF_FCB6 Reserved Reserved 0x03FF_FCB6 PROG14_MPPAR 0x03FF_FCB0 0x03FF_FCA4 0x03FF_FCB6 Reserved Reserved 0x03FF_FCA4 PROG15_MPPAR 0x03FF_FCB6 0x03FF_FCA4 0x03FF_FCB6 Reserved Reserved 0x03FF_FCA4 Table 8-20. MPU6-MPU11 Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) Reset Values Register MPU6 MPU7 MPU8 MPU9 MPU10 MPU11 PROG0_MPPAR Reserved 0x03FF_FCB6 0x03FF_FCBF 0x03FF_FCB6 0x03FF_FCB6 0x03FF_FCB6 PROG1_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 0x03FF_FCB6 0x03FF_FCB0 PROG2_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG3_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG4_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG5_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG6_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG7_MPPAR Reserved 0x03FF_FCBF 0x03FF_FCB6 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG8_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG9_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG10_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG11_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG12_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG13_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB6 PROG14_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB0 PROG15_MPPAR Reserved 0x03FF_FCBF N/A 0x03FF_FCB6 N/A 0x03FF_FCB6 Table 8-21. MPU12-MPU14 Programmable Range n Memory Protection Page Attribute Register (PROGn_MPPAR) Reset Values Register MPU12 MPU13 MPU14 PROG0_MPPAR 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCBF PROG1_MPPAR 0x03FF_FCBF 0x03FF_FCBF 0x03FF_FCBF PROG2_MPPAR 0x0000_0000 0x0000_0000 0x0000_0000 PROG3_MPPAR N/A N/A N/A PROG4_MPPAR N/A N/A N/A PROG5_MPPAR N/A N/A N/A PROG6_MPPAR N/A N/A N/A PROG7_MPPAR N/A N/A N/A PROG8_MPPAR N/A N/A N/A PROG9_MPPAR N/A N/A N/A PROG10_MPPAR N/A N/A N/A PROG11_MPPAR N/A N/A N/A PROG12_MPPAR N/A N/A N/A PROG13_MPPAR N/A N/A N/A PROG14_MPPAR N/A N/A N/A PROG15_MPPAR N/A N/A N/A 92 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 8.3 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Interrupts for 66AK2Hxx This section discusses the interrupt sources, controller, and topology. Also provided are tables describing the interrupt events. 8.3.1 Interrupt Sources and Interrupt Controller The CPU interrupts on the 66AK2Hxx device are configured through the C66x CorePac Interrupt Controller. The Interrupt Controller allows for up to 128 system events to be programmed to any of the 12 CPU interrupt inputs (CPUINT4 - CPUINT15), the CPU exception input (EXCEP), or the advanced emulation logic. The 128 system events consist of both internally-generated events (within the CorePac) and chip-level events. Additional system events are routed to each of the C66x CorePacs to provide chip-level events that are not required as CPU interrupts/exceptions to be routed to the Interrupt Controller as emulation events. In addition, error-class events or infrequently used events are also routed through the system event router to offload the C66x CorePac interrupt selector. This is accomplished through the CorePac Interrupt Controller blocks, CIC[2:0]. This is clocked using CPU/6. The event controllers consist of simple combination logic to provide additional events to each C66x CorePac, ARM GIC (ARM Generic Interrupt Controller) plus the EDMA3CC. CIC0 has 104 event outputs which provides 20 broadcast events and 18 additional events to each of the C66x CorePacs, 0 through 3. Similarly, CIC1 has 104 event outputs which provides 20 broadcast events and 18 additional events to each of the C66x CorePacs, 4 through 7 (66AK2H12/14 only). CIC2 has 103 event outputs which provides 8, 20, 8, 8, 8, and 16 events to EDMA3CC0, EDMA3CC1, EDMA3C2, EDMA3CC3, EDMA3CC4, and HyperLinks respectively. The events that are routed to the C66x CorePacs for Advanced Event Triggering (AET) purposes from those EDMA3CC and FSYNC events that are not otherwise provided to each C66x CorePac. Modules such as CP_MPU, BOOT_CFG, and CP_Tracer have level interrupts and EOI handshaking interface. The EOI value is 0 for CP_MPU, BOOT_CFG, and CP_Tracer. Figure 8-4 and Figure 8-5 show the 66AK2Hxx interrupt topologies. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 93 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 57 Shared Primary Events 19 Unique Primary Events 12 Reserved Events 18 Secondary Events 26 QMSS q_pend Events 19 Unique Primary Events 18 Secondary Events 9 QMSS q_pend Events C66x CorePac0 C66x CorePac1 CIC0 19 Unique Primary Events 18 Secondary Events C66x CorePac2 32 QMSS lo Events 19 Unique Primary Events 18 Secondary Events 402 Common Events 20 Broadcast Events from CIC0 19 Unique Primary Events 402 Common Events 18 Secondary Events 12 Reserved Events C66x CorePac4 19 Unique Primary Events 18 Secondary Events 26 QMSS q_pend Events C66x CorePac3 C66x CorePac5 CIC1 19 Unique Primary Events 18 Secondary Events C66x CorePac6 9 QMSS q_pend Events 19 Unique Primary Events 18 Secondary Events 32 QMSS_lo Events C66x CorePac7 20 Broadcast Events from CIC1 8 Shared Events 24 × 2 Primary Events 39 QMSS q_pend Events 8 × 2 Secondary Events 56 Primary Events 32 QMSS_1 hi Events 8 Secondary Events 44 Primary Events 32 QMSS_2 hi Events 20 Secondary Events HyperLink EDMA3 CC0 EDMA3 CC1 CIC2 56 Primary Events 357 Common Events 8 Secondary Events 56 Primary Events 19 Reserved Events 8 Secondary Events 56 Primary Events 66AK2H14/12 8 Secondary Events 36 Peripherals 480 SPI Events EDMA3 CC2 EDMA3 CC3 EDMA3 CC4 ARM INTC Figure 8-4. 66AK2H14/12 Interrupt Topology 94 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 57 Shared Primary Events 19 Unique Primary Events 12 Reserved Events 18 Secondary Events 26 QMSS q_pend Events C66x CorePac0 19 Unique Primary Events 18 Secondary Events 9 QMSS q_pend Events C66x CorePac1 CIC0 19 Unique Primary Events 18 Secondary Events C66x CorePac2 32 QMSS lo Events 19 Unique Primary Events 18 Secondary Events 402 Common Events C66x CorePac3 20 Broadcast Events from CIC0 4 Shared Events 24 × 2 Primary Events 39 QMSS q_pend Events 8 × 2 Secondary Events 56 Primary Events 32 QMSS_1 hi Events 8 Secondary Events 44 Primary Events 32 QMSS_2 hi Events 20 Secondary Events HyperLink EDMA3 CC0 EDMA3 CC1 CIC2 56 Primary Events 357 Common Events 8 Secondary Events 56 Primary Events 19 Reserved Events 8 Secondary Events 56 Primary Events 66AK2H06 8 Secondary Events 36 480 SPI Events Peripherals EDMA3 CC2 EDMA3 CC3 EDMA3 CC4 ARM INTC Figure 8-5. 66AK2H06 Interrupt Topology Table 8-22 shows the mapping of primary events to C66x Corepac. Table 8-22. System Event Mapping — C66x CorePac Primary Interrupts EVENT NO. EVENT NAME DESCRIPTION 0 EVT0 Event combiner 0 output 1 EVT1 Event combiner 1 output 2 EVT2 Event combiner 2 output 3 EVT3 Event combiner 3 output 4 TETB_HFULLINTN TETB is half full 5 TETB_FULLINTN TETB is full 6 TETB_ACQINTN TETB Acquisition complete interrupt 7 TETB_OVFLINTN TETB Overflow condition interrupt 8 TETB_UNFLINTN TETB Underflow condition interrupt 9 EMU_DTDMA Emulation interrupt for host scan, DTDMA transfer complete and AET Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 95 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-22. System Event Mapping — C66x CorePac Primary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 10 MSMC_MPF_ERRORN Memory protection fault indicators for system master PrivID = 0 (C66x CorePac) 11 Reserved Reserved 12 Reserved Reserved 13 IDMA0 IDMA channel 0 interrupt 14 IDMA1 IDMA channel 1 interrupt 15 SEM_ERRN Semaphore error interrupt 16 SEM_INTN Semaphore interrupt 17 PCIE_INT4_PLUS_N PCIE0 MSI interrupt 18 Reserved Reserved 19 Reserved Reserved 20 SRIO_INTDST16_PLUS_N SRIO interrupt 21 Reserved Reserved 22 Reserved Reserved 23 CIC_OUT35 CIC Interrupt Controller output (1) 24 CIC_2_OUT102 CIC Interrupt Controller output 25 CIC_2_OUT94_PLUS_N (2) CIC Interrupt Controller output 26 CIC_OUT68_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 27 CIC_OUT69_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 28 CIC_OUT70_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 29 CIC_OUT71_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 30 CIC_OUT72_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 31 CIC_OUT73_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 32 CIC_OUT16 CIC Interrupt Controller output (1) 33 CIC_OUT17 CIC Interrupt Controller output (1) 34 CIC_OUT18 CIC Interrupt Controller output (1) 35 CIC_OUT19 CIC Interrupt Controller output (1) 36 CIC_OUT20 CIC Interrupt Controller output (1) 37 CIC_OUT21 CIC Interrupt Controller output (1) 38 CIC_OUT22 CIC Interrupt Controller output (1) 39 CIC_OUT23 CIC Interrupt Controller output (1) 40 CIC_OUT32 CIC Interrupt Controller output (1) 41 CIC_OUT33 CIC Interrupt Controller output (1) 42 CIC_OUT13_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 43 CIC_OUT14_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 44 CIC_OUT15_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 45 CIC_OUT64_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 46 CIC_OUT65_PLUS_10_MUL_N (2) CIC Interrupt Controller output (1) 47 (2) CIC Interrupt Controller output (1) CIC_OUT66_PLUS_10_MUL_N (2) 48 QMSS_INTD_1_HIGH_N 49 QMSS_INTD_1_HIGH_8_PLUS_N (2) Navigator 1 accumulated hi-priority interrupt 0 Navigator 1 accumulated hi-priority interrupt 8 50 QMSS_INTD_1_HIGH_16_PLUS_N (2) Navigator 1 accumulated hi-priority interrupt 16 51 QMSS_INTD_1_HIGH_24_PLUS_N (2) Navigator 1 accumulated hi-priority interrupt 24 52 QMSS_INTD_2_HIGH_N (2) Navigator 2 accumulated hi-priority interrupt 0 53 (1) (2) 96 QMSS_INTD_2_HIGH_8_PLUS_N (2) Navigator 2 accumulated hi-priority interrupt 8 For C66x CorePac[0-3], this generic primary interrupt comes from CIC0 and for C66x CorePac[4-7], this generic primary interrupt comes from CIC1. N = core number. Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-22. System Event Mapping — C66x CorePac Primary Interrupts (continued) EVENT NO. EVENT NAME 54 QMSS_INTD_2_HIGH_16_PLUS_N (2) DESCRIPTION Navigator 2 accumulated hi-priority interrupt 16 55 QMSS_INTD_2_HIGH_24_PLUS_N (2) Navigator 2 accumulated hi-priority interrupt 24 56 CIC_OUT0 CIC Interrupt Controller output (1) 57 CIC_OUT1 CIC Interrupt Controller output (1) 58 CIC_OUT2 CIC Interrupt Controller output (1) 59 CIC_OUT3 CIC Interrupt Controller output (1) 60 CIC_OUT4 CIC Interrupt Controller output (1) 61 CIC_OUT5 CIC Interrupt Controller output (1) 62 CIC_OUT6 CIC Interrupt Controller output (1) 63 CIC_OUT7 CIC Interrupt Controller output (1) 64 TIMER_N_INTL Local timer interrupt low 65 TIMER_N_INTH Local timer interrupt high 66 TIMER_8_INTL Timer interrupt low 67 TIMER_8_INTH Timer interrupt high 68 TIMER_9_INTL Timer interrupt low 69 TIMER_9_INTH Timer interrupt high 70 TIMER_10_INTL Timer interrupt low 71 TIMER_10_INTH Timer interrupt high 72 TIMER_11_INTL Timer interrupt low 73 TIMER_11_INTH Timer interrupt high 74 CIC_OUT8_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 75 (2) CIC Interrupt Controller output (1) CIC_OUT9_PLUS_16_MUL_N 76 CIC_OUT10_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 77 CIC_OUT11_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 78 TIMER_14_INTL Timer interrupt low 79 TIMER_14_INTH Timer interrupt high 80 TIMER_15_INTL Timer interrupt low 81 TIMER_15_INTH Timer interrupt high 82 GPIO_INT8 Local GPIO interrupt 83 GPIO_INT9 Local GPIO interrupt 84 GPIO_INT10 Local GPIO interrupt 85 GPIO_INT11 Local GPIO interrupt 86 GPIO_INT12 Local GPIO interrupt 87 Reserved Reserved 88 Reserved Reserved 89 Reserved Reserved 90 Reserved Reserved 91 Reserved Reserved 92 Reserved Reserved 93 Reserved Reserved 94 Reserved Reserved (2) CIC Interrupt Controller output (1) 95 CIC_OUT67_PLUS_10_MUL_N 96 INTERR Dropped C66x CorePac interrupt event 97 EMC_IDMAERR Invalid IDMA parameters 98 Reserved Reserved 99 CIC_2_SPECIAL_BROADCAST CIC Interrupt Controller output 100 EFIINT0 EFI interrupt from Side A Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 97 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-22. System Event Mapping — C66x CorePac Primary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 101 EFIINT1 EFI interrupt from Side B 102 GPIO_INT13 Local GPIO interrupt 103 GPIO_INT14 Local GPIO interrupt 104 GPIO_INT15 Local GPIO interrupt 105 IPC_GRN Boot CFG 106 GPIO_INTN GPIO interrupt 107 CIC_OUT12_PLUS_16_MUL_N (2) CIC Interrupt Controller output (1) 108 CIC_OUT34 CIC Interrupt Controller output (1) 109 CIC_2_OUT13 CIC Interrupt Controller output 110 MDMAERREVT DMA internal bus error event 111 Reserved Reserved 112 EDMACC_0_4_TC_AET_INT EDMA3CC0_4 AET event 113 PMC_ED Single bit error detected during DMA read 114 EDMACC_1_2_TC_AET_INT EDMA3CC1_2 AET event 115 EDMACC_1_3_TC_AET_INT EDMA3CC3_4 AET event 116 UMC_ED1 Corrected bit error detected 117 UMC_ED2 Uncorrected bit error detected 118 PDC_INT Power down sleep interrupt 119 SYS_CMPA SYS CPU MP fault event 120 PMC_CMPA CPU memory protection fault 121 PMC_DMPA DMA memory protection fault 122 DMC_CMPA CPU memory protection fault 123 DMC_DMPA DMA memory protection fault 124 UMC_CMPA CPU memory protection fault 125 UMC_DMPA DMA memory protection fault 126 EMC_CMPA CPU memory protection fault 127 EMC_BUSERR Bus error interrupt NOTE Event No. 0 is identical to ARM GIC interrupt ID 0. Table 8-23. System Event Mapping — ARM CorePac Interrupts EVENT NO. EVENT NAME DESCRIPTION 0 RSTMUX_INT8 Boot config watchdog timer expiration (timer 16) event for ARM Core 0 1 RSTMUX_INT9 Boot config watchdog timer expiration (timer 17) event for ARM Core 1 2 RSTMUX_INT10 Boot config watchdog timer expiration (timer 18) event for ARM Core 2 (1) 3 RSTMUX_INT11 Boot config watchdog timer expiration (timer 19) event for ARM Core 3 (1) 4 IPC_GR8 Boot config IPCG 5 IPC_GR9 Boot config IPCG 6 IPC_GR10 Boot config IPCG 7 IPC_GR11 Boot config IPCG 8 SEM_INT8 Semaphore interrupt 9 SEM_INT9 Semaphore interrupt (1) 98 66AK2H12/14 only. Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 10 SEM_INT10 Semaphore interrupt 11 SEM_INT11 Semaphore interrupt 12 SEM_ERR8 Semaphore error interrupt 13 SEM_ERR9 Semaphore error interrupt 14 SEM_ERR10 Semaphore error interrupt 15 SEM_ERR11 Semaphore error interrupt 16 MSMC_MPF_ERROR8 Memory protection fault indicators for system master PrivID = 8 17 MSMC_MPF_ERROR9 Memory protection fault indicators for system master PrivID = 9 18 MSMC_MPF_ERROR10 Memory protection fault indicators for system master PrivID = 10 19 MSMC_MPF_ERROR11 Memory protection fault indicators for system master PrivID = 11 20 ARM_NPMUIRQ0 ARM performance monitoring unit interrupt request 21 ARM_NPMUIRQ1 ARM performance monitoring unit interrupt request 22 ARM_NPMUIRQ2 ARM performance monitoring unit interrupt request 23 ARM_NPMUIRQ3 ARM performance monitoring unit interrupt request 24 ARM_NINTERRIRQ ARM internal memory ECC error interrupt request 25 ARM_NAXIERRIRQ ARM bus error interrupt request 26 PCIE_INT0 PCIE legacy INTA interrupt 27 PCIE_INT1 PCIE legacy INTB interrupt 28 PCIE_INT2 PCIE legacy INTC interrupt 29 PCIE_INT3 PCIE legacy INTD interrupt 30 PCIE_INT4 PCIE MSI interrupt 31 PCIE_INT5 PCIE MSI interrupt 32 PCIE_INT6 PCIE MSI interrupt 33 PCIE_INT7 PCIE MSI interrupt 34 PCIE_INT8 PCIE MSI interrupt 35 PCIE_INT9 PCIE MSI interrupt 36 PCIE_INT10 PCIE MSI interrupt 37 PCIE_INT11 PCIE MSI interrupt 38 PCIE_INT12 PCIE error interrupt 39 PCIE_INT13 PCIE power management interrupt 40 QMSS_QUE_PEND_658 Navigator transmit queue pending event for indicated queue 41 QMSS_QUE_PEND_659 Navigator transmit queue pending event for indicated queue 42 QMSS_QUE_PEND_660 Navigator transmit queue pending event for indicated queue 43 QMSS_QUE_PEND_661 Navigator transmit queue pending event for indicated queue 44 QMSS_QUE_PEND_662 Navigator transmit queue pending event for indicated queue 45 QMSS_QUE_PEND_663 Navigator transmit queue pending event for indicated queue 46 QMSS_QUE_PEND_664 Navigator transmit queue pending event for indicated queue 47 QMSS_QUE_PEND_665 Navigator transmit queue pending event for indicated queue 48 QMSS_QUE_PEND_8704 Navigator transmit queue pending event for indicated queue 49 QMSS_QUE_PEND_8705 Navigator transmit queue pending event for indicated queue 50 QMSS_QUE_PEND_8706 Navigator transmit queue pending event for indicated queue 51 QMSS_QUE_PEND_8707 Navigator transmit queue pending event for indicated queue 52 QMSS_QUE_PEND_8708 Navigator transmit queue pending event for indicated queue 53 QMSS_QUE_PEND_8709 Navigator transmit queue pending event for indicated queue 54 QMSS_QUE_PEND_8710 Navigator transmit queue pending event for indicated queue 55 QMSS_QUE_PEND_8711 Navigator transmit queue pending event for indicated queue 56 QMSS_QUE_PEND_8712 Navigator transmit queue pending event for indicated queue Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 99 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 57 QMSS_QUE_PEND_8713 Navigator transmit queue pending event for indicated queue 58 QMSS_QUE_PEND_8714 Navigator transmit queue pending event for indicated queue 59 QMSS_QUE_PEND_8715 Navigator transmit queue pending event for indicated queue 60 QMSS_QUE_PEND_8716 Navigator transmit queue pending event for indicated queue 61 QMSS_QUE_PEND_8717 Navigator transmit queue pending event for indicated queue 62 QMSS_QUE_PEND_8718 Navigator transmit queue pending event for indicated queue 63 QMSS_QUE_PEND_8719 Navigator transmit queue pending event for indicated queue 64 QMSS_QUE_PEND_8720 Navigator transmit queue pending event for indicated queue 65 QMSS_QUE_PEND_8721 Navigator transmit queue pending event for indicated queue 66 QMSS_QUE_PEND_8722 Navigator transmit queue pending event for indicated queue 67 QMSS_QUE_PEND_8723 Navigator transmit queue pending event for indicated queue 68 QMSS_QUE_PEND_8724 Navigator transmit queue pending event for indicated queue 69 QMSS_QUE_PEND_8725 Navigator transmit queue pending event for indicated queue 70 QMSS_QUE_PEND_8726 Navigator transmit queue pending event for indicated queue 71 QMSS_QUE_PEND_8727 Navigator transmit queue pending event for indicated queue 72 QMSS_QUE_PEND_8728 Navigator transmit queue pending event for indicated queue 73 QMSS_QUE_PEND_8729 Navigator transmit queue pending event for indicated queue 74 QMSS_QUE_PEND_8730 Navigator transmit queue pending event for indicated queue 75 QMSS_QUE_PEND_8731 Navigator transmit queue pending event for indicated queue 76 QMSS_QUE_PEND_8732 Navigator transmit queue pending event for indicated queue 77 QMSS_QUE_PEND_8733 Navigator transmit queue pending event for indicated queue 78 QMSS_QUE_PEND_8734 Navigator transmit queue pending event for indicated queue 79 QMSS_QUE_PEND_8735 Navigator transmit queue pending event for indicated queue 80 TIMER_0_INTL Timer interrupt low 81 TIMER_0_INTH Timer interrupt high 82 TIMER_1_INTL Timer interrupt low 83 TIMER_1_INTH Timer interrupt high 84 TIMER_2_INTL Timer interrupt low 85 TIMER_2_INTH Timer interrupt high 86 TIMER_3_INTL Timer interrupt low 87 TIMER_3_INTH Timer interrupt high 88 TIMER_4_INTL Timer interrupt low (1) 89 TIMER_4_INTH Timer interrupt high (1) 90 TIMER_5_INTL Timer interrupt low (1) 91 TIMER_5_INTH Timer interrupt high (1) 92 TIMER_6_INTL Timer interrupt low (1) 93 TIMER_6_INTH Timer interrupt high (1) 94 TIMER_7_INTL Timer interrupt low (1) 95 TIMER_7_INTH Timer interrupt high (1) 96 TIMER_8_INTL Timer interrupt low 97 TIMER_8_INTH Timer interrupt high 98 TIMER_9_INTL Timer interrupt low 99 TIMER_9_INTH Timer interrupt high 100 TIMER_10_INTL Timer interrupt low 101 TIMER_10_INTH Timer interrupt high 102 TIMER_11_INTL Timer interrupt low 103 TIMER_11_INTH Timer interrupt high 100 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 104 TIMER_12_INTL Timer interrupt low 105 TIMER_12_INTH Timer interrupt high 106 TIMER_13_INTL Timer interrupt low 107 TIMER_13_INTH Timer interrupt high 108 TIMER_14_INTL Timer interrupt low 109 TIMER_14_INTH Timer interrupt high 110 TIMER_15_INTL Timer interrupt low 111 TIMER_15_INTH Timer interrupt high 112 TIMER_16_INTL Timer interrupt low 113 TIMER_16_INTH Timer interrupt high 114 TIMER_17_INTL Timer interrupt low 115 TIMER_17_INTH Timer interrupt high 116 TIMER_18_INTL Timer interrupt low (1) 117 TIMER_18_INTH Timer interrupt high (1) 118 TIMER_19_INTL Timer interrupt low (1) 119 TIMER_19_INTH Timer interrupt high (1) 120 GPIO_INT0 GPIO interrupt 121 GPIO_INT1 GPIO interrupt 122 GPIO_INT2 GPIO interrupt 123 GPIO_INT3 GPIO interrupt 124 GPIO_INT4 GPIO interrupt 125 GPIO_INT5 GPIO interrupt 126 GPIO_INT6 GPIO interrupt 127 GPIO_INT7 GPIO interrupt 128 GPIO_INT8 GPIO interrupt 129 GPIO_INT9 GPIO interrupt 130 GPIO_INT10 GPIO interrupt 131 GPIO_INT11 GPIO interrupt 132 GPIO_INT12 GPIO interrupt 133 GPIO_INT13 GPIO interrupt 134 GPIO_INT14 GPIO interrupt 135 GPIO_INT15 GPIO interrupt 136 GPIO_INT16 GPIO interrupt 137 GPIO_INT17 GPIO interrupt 138 GPIO_INT18 GPIO interrupt 139 GPIO_INT19 GPIO interrupt 140 GPIO_INT20 GPIO interrupt 141 GPIO_INT21 GPIO interrupt 142 GPIO_INT22 GPIO interrupt 143 GPIO_INT23 GPIO interrupt 144 GPIO_INT24 GPIO interrupt 145 GPIO_INT25 GPIO interrupt 146 GPIO_INT26 GPIO interrupt 147 GPIO_INT27 GPIO interrupt 148 GPIO_INT28 GPIO interrupt 149 GPIO_INT29 GPIO interrupt 150 GPIO_INT30 GPIO interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 101 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 151 GPIO_INT31 GPIO interrupt 152 SRIO_INT00 SRIO interrupt 153 SRIO_INT01 SRIO interrupt 154 SRIO_INT02 SRIO interrupt 155 SRIO_INT03 SRIO interrupt 156 SRIO_INT04 SRIO interrupt 157 SRIO_INT05 SRIO interrupt 158 SRIO_INT06 SRIO interrupt 159 SRIO_INT07 SRIO interrupt 160 SRIO_INT08 SRIO interrupt 161 SRIO_INT09 SRIO interrupt 162 SRIO_INT10 SRIO interrupt 163 SRIO_INT11 SRIO interrupt 164 SRIO_INT12 SRIO interrupt 165 SRIO_INT13 SRIO interrupt 166 SRIO_INT14 SRIO interrupt 167 SRIO_INT15 SRIO interrupt 168 SRIO_INT16 SRIO interrupt 169 SRIO_INT17 SRIO interrupt 170 SRIO_INT18 SRIO interrupt 171 SRIO_INT19 SRIO interrupt 172 SRIO_INT20 SRIO interrupt 173 SRIO_INT21 SRIO interrupt 174 SRIO_INT22 SRIO interrupt 175 SRIO_INT23 SRIO interrupt 176 SRIO_INT_PKTDMA_0 SRIO interrupt for Packet DMA starvation 177 QMSS_INTD_1_PKTDMA_0 Navigator interrupt for Packet DMA starvation 178 QMSS_INTD_1_PKTDMA_1 Navigator interrupt for Packet DMA starvation 179 QMSS_INTD_1_HIGH_0 Navigator hi interrupt 180 QMSS_INTD_1_HIGH_1 Navigator hi interrupt 181 QMSS_INTD_1_HIGH_2 Navigator hi interrupt 182 QMSS_INTD_1_HIGH_3 Navigator hi interrupt 183 QMSS_INTD_1_HIGH_4 Navigator hi interrupt 184 QMSS_INTD_1_HIGH_5 Navigator hi interrupt 185 QMSS_INTD_1_HIGH_6 Navigator hi interrupt 186 QMSS_INTD_1_HIGH_7 Navigator hi interrupt 187 QMSS_INTD_1_HIGH_8 Navigator hi interrupt 188 QMSS_INTD_1_HIGH_9 Navigator hi interrupt 189 QMSS_INTD_1_HIGH_10 Navigator hi interrupt 190 QMSS_INTD_1_HIGH_11 Navigator hi interrupt 191 QMSS_INTD_1_HIGH_12 Navigator hi interrupt 192 QMSS_INTD_1_HIGH_13 Navigator hi interrupt 193 QMSS_INTD_1_HIGH_14 Navigator hi interrupt 194 QMSS_INTD_1_HIGH_15 Navigator hi interrupt 195 QMSS_INTD_1_HIGH_16 Navigator hi interrupt 196 QMSS_INTD_1_HIGH_17 Navigator hi interrupt 197 QMSS_INTD_1_HIGH_18 Navigator hi interrupt 102 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 198 QMSS_INTD_1_HIGH_19 Navigator hi interrupt 199 QMSS_INTD_1_HIGH_20 Navigator hi interrupt 200 QMSS_INTD_1_HIGH_21 Navigator hi interrupt 201 QMSS_INTD_1_HIGH_22 Navigator hi interrupt 202 QMSS_INTD_1_HIGH_23 Navigator hi interrupt 203 QMSS_INTD_1_HIGH_24 Navigator hi interrupt 204 QMSS_INTD_1_HIGH_25 Navigator hi interrupt 205 QMSS_INTD_1_HIGH_26 Navigator hi interrupt 206 QMSS_INTD_1_HIGH_27 Navigator hi interrupt 207 QMSS_INTD_1_HIGH_28 Navigator hi interrupt 208 QMSS_INTD_1_HIGH_29 Navigator hi interrupt 209 QMSS_INTD_1_HIGH_30 Navigator hi interrupt 210 QMSS_INTD_1_HIGH_31 Navigator hi interrupt 211 QMSS_INTD_1_LOW_0 Navigator interrupt 212 QMSS_INTD_1_LOW_1 Navigator interrupt 213 QMSS_INTD_1_LOW_2 Navigator interrupt 214 QMSS_INTD_1_LOW_3 Navigator interrupt 215 QMSS_INTD_1_LOW_4 Navigator interrupt 216 QMSS_INTD_1_LOW_5 Navigator interrupt 217 QMSS_INTD_1_LOW_6 Navigator interrupt 218 QMSS_INTD_1_LOW_7 Navigator interrupt 219 QMSS_INTD_1_LOW_8 Navigator interrupt 220 QMSS_INTD_1_LOW_9 Navigator interrupt 221 QMSS_INTD_1_LOW_10 Navigator interrupt 222 QMSS_INTD_1_LOW_11 Navigator interrupt 223 QMSS_INTD_1_LOW_12 Navigator interrupt 224 QMSS_INTD_1_LOW_13 Navigator interrupt 225 QMSS_INTD_1_LOW_14 Navigator interrupt 226 QMSS_INTD_1_LOW_15 Navigator interrupt 227 QMSS_INTD_2_PKTDMA_0 Navigator interrupt for Packet DMA starvation 228 QMSS_INTD_2_PKTDMA_1 Navigator interrupt for Packet DMA starvation 229 QMSS_INTD_2_HIGH_0 Navigator second hi interrupt 230 QMSS_INTD_2_HIGH_1 Navigator second hi interrupt 231 QMSS_INTD_2_HIGH_2 Navigator second hi interrupt 232 QMSS_INTD_2_HIGH_3 Navigator second hi interrupt 233 QMSS_INTD_2_HIGH_4 Navigator second hi interrupt 234 QMSS_INTD_2_HIGH_5 Navigator second hi interrupt 235 QMSS_INTD_2_HIGH_6 Navigator second hi interrupt 236 QMSS_INTD_2_HIGH_7 Navigator second hi interrupt 237 QMSS_INTD_2_HIGH_8 Navigator second hi interrupt 238 QMSS_INTD_2_HIGH_9 Navigator second hi interrupt 239 QMSS_INTD_2_HIGH_10 Navigator second hi interrupt 240 QMSS_INTD_2_HIGH_11 Navigator second hi interrupt 241 QMSS_INTD_2_HIGH_12 Navigator second hi interrupt 242 QMSS_INTD_2_HIGH_13 Navigator second hi interrupt 243 QMSS_INTD_2_HIGH_14 Navigator second hi interrupt 244 QMSS_INTD_2_HIGH_15 Navigator second hi interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 103 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 245 QMSS_INTD_2_HIGH_16 Navigator second hi interrupt 246 QMSS_INTD_2_HIGH_17 Navigator second hi interrupt 247 QMSS_INTD_2_HIGH_18 Navigator second hi interrupt 248 QMSS_INTD_2_HIGH_19 Navigator second hi interrupt 249 QMSS_INTD_2_HIGH_20 Navigator second hi interrupt 250 QMSS_INTD_2_HIGH_21 Navigator second hi interrupt 251 QMSS_INTD_2_HIGH_22 Navigator second hi interrupt 252 QMSS_INTD_2_HIGH_23 Navigator second hi interrupt 253 QMSS_INTD_2_HIGH_24 Navigator second hi interrupt 254 QMSS_INTD_2_HIGH_25 Navigator second hi interrupt 255 QMSS_INTD_2_HIGH_26 Navigator second hi interrupt 256 QMSS_INTD_2_HIGH_27 Navigator second hi interrupt 257 QMSS_INTD_2_HIGH_28 Navigator second hi interrupt 258 QMSS_INTD_2_HIGH_29 Navigator second hi interrupt 259 QMSS_INTD_2_HIGH_30 Navigator second hi interrupt 260 QMSS_INTD_2_HIGH_31 Navigator second hi interrupt 261 QMSS_INTD_2_LOW_0 Navigator second interrupt 262 QMSS_INTD_2_LOW_1 Navigator second interrupt 263 QMSS_INTD_2_LOW_2 Navigator second interrupt 264 QMSS_INTD_2_LOW_3 Navigator second interrupt 265 QMSS_INTD_2_LOW_4 Navigator second interrupt 266 QMSS_INTD_2_LOW_5 Navigator second interrupt 267 QMSS_INTD_2_LOW_6 Navigator second interrupt 268 QMSS_INTD_2_LOW_7 Navigator second interrupt 269 QMSS_INTD_2_LOW_8 Navigator second interrupt 270 QMSS_INTD_2_LOW_9 Navigator second interrupt 271 QMSS_INTD_2_LOW_10 Navigator second interrupt 272 QMSS_INTD_2_LOW_11 Navigator second interrupt 273 QMSS_INTD_2_LOW_12 Navigator second interrupt 274 QMSS_INTD_2_LOW_13 Navigator second interrupt 275 QMSS_INTD_2_LOW_14 Navigator second interrupt 276 QMSS_INTD_2_LOW_15 Navigator second interrupt 277 UART_0_UARTINT UART0 interrupt 278 UART_0_URXEVT UART0 receive event 279 UART_0_UTXEVT UART0 transmit event 280 UART_1_UARTINT UART1 interrupt 281 UART_1_URXEVT UART1 receive event 282 UART_1_UTXEVT UART1 transmit event 283 I2C_0_INT I2C interrupt 284 I2C_0_REVT I2C receive event 285 I2C_0_XEVT I2C transmit event 286 I2C_1_INT I2C interrupt 287 I2C_1_REVT I2C receive event 288 I2C_1_XEVT I2C transmit event 289 I2C_2_INT I2C interrupt 290 I2C_2_REVT I2C receive event 291 I2C_2_XEVT I2C transmit event 104 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 292 SPI_0_INT0 SPI interrupt 293 SPI_0_INT1 SPI interrupt 294 SPI_0_XEVT SPI DMA TX event 295 SPI_0_REVT SPI DMA RX event 296 SPI_1_INT0 SPI interrupt 297 SPI_1_INT1 SPI interrupt 298 SPI_1_XEVT SPI DMA TX event 299 SPI_1_REVT SPI DMA RX event 300 SPI_2_INT0 SPI interrupt 301 SPI_2_INT1 SPI interrupt 302 SPI_2_XEVT SPI DMA TX event 303 SPI_2_REVT SPI DMA RX event 304 DBGTBR_DMAINT Debug trace buffer (TBR) DMA event 305 DBGTBR_ACQCOMP Debug trace buffer (TBR) Acquisition has been completed 306 ARM_TBR_DMA ARM trace buffer (TBR) DMA event 307 ARM_TBR_ACQ ARM trace buffer (TBR) Acquisition has been completed 308 NETCP_MDIO_LINK_INT0 Packet Accelerator subsystem MDIO interrupt 309 NETCP_MDIO_LINK_INT1 Packet Accelerator subsystem MDIO interrupt 310 NETCP_MDIO_USER_INT0 Packet Accelerator subsystem MDIO interrupt 311 NETCP_MDIO_USER_INT1 Packet Accelerator subsystem MDIO interrupt 312 NETCP_MISC_INT Packet Accelerator subsystem MDIO interrupt 313 NETCP_PKTDMA_INT0 Packet Accelerator Packet DMA starvation interrupt 314 EDMACC_0_GINT EDMA3CC0 global completion interrupt 315 EDMACC_0_TC_0_INT EDMA3CC0 individual completion interrupt 316 EDMACC_0_TC_1_INT EDMA3CC0 individual completion interrupt 317 EDMACC_0_TC_2_INT EDMA3CC0 individual completion interrupt 318 EDMACC_0_TC_3_INT EDMA3CC0 individual completion interrupt 319 EDMACC_0_TC_4_INT EDMA3CC0 individual completion interrupt 320 EDMACC_0_TC_5_INT EDMA3CC0 individual completion interrupt 321 EDMACC_0_TC_6_INT EDMA3CC0 individual completion interrupt 322 EDMACC_0_TC_7_INT EDMA3CC0 individual completion interrupt 323 EDMACC_1_GINT EDMA3CC1 global completion interrupt 324 EDMACC_1_TC_0_INT EDMA3CC1 individual completion interrupt 325 EDMACC_1_TC_1_INT EDMA3CC1 individual completion interrupt 326 EDMACC_1_TC_2_INT EDMA3CC1 individual completion interrupt 327 EDMACC_1_TC_3_INT EDMA3CC1 individual completion interrupt 328 EDMACC_1_TC_4_INT EDMA3CC1 individual completion interrupt 329 EDMACC_1_TC_5_INT EDMA3CC1 individual completion interrupt 330 EDMACC_1_TC_6_INT EDMA3CC1 individual completion interrupt 331 EDMACC_1_TC_7_INT EDMA3CC1 individual completion interrupt 332 EDMACC_2_GINT EDMA3CC2 global completion interrupt 333 EDMACC_2_TC_0_INT EDMA3CC2 individual completion interrupt 334 EDMACC_2_TC_1_INT EDMA3CC2 individual completion interrupt 335 EDMACC_2_TC_2_INT EDMA3CC2 individual completion interrupt 336 EDMACC_2_TC_3_INT EDMA3CC2 individual completion interrupt 337 EDMACC_2_TC_4_INT EDMA3CC2 individual completion interrupt 338 EDMACC_2_TC_5_INT EDMA3CC2 individual completion interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 105 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 339 EDMACC_2_TC_6_INT EDMA3CC2 individual completion interrupt 340 EDMACC_2_TC_7_INT EDMA3CC2 individual completion interrupt 341 EDMACC_3_GINT EDMA3CC3 global completion interrupt 342 EDMACC_3_TC_0_INT EDMA3CC3 individual completion interrupt 343 EDMACC_3_TC_1_INT EDMA3CC3 individual completion interrupt 344 EDMACC_3_TC_2_INT EDMA3CC3 individual completion interrupt 345 EDMACC_3_TC_3_INT EDMA3CC3 individual completion interrupt 346 EDMACC_3_TC_4_INT EDMA3CC3 individual completion interrupt 347 EDMACC_3_TC_5_INT EDMA3CC3 individual completion interrupt 348 EDMACC_3_TC_6_INT EDMA3CC3 individual completion interrupt 349 EDMACC_3_TC_7_INT EDMA3CC3 individual completion interrupt 350 EDMACC_4_GINT EDMA3CC4 global completion interrupt 351 EDMACC_4_TC_0_INT EDMA3CC4 individual completion interrupt 352 EDMACC_4_TC_1_INT EDMA3CC4 individual completion interrupt 353 EDMACC_4_TC_2_INT EDMA3CC4 individual completion interrupt 354 EDMACC_4_TC_3_INT EDMA3CC4 individual completion interrupt 355 EDMACC_4_TC_4_INT EDMA3CC4 individual completion interrupt 356 EDMACC_4_TC_5_INT EDMA3CC4 individual completion interrupt 357 EDMACC_4_TC_6_INT EDMA3CC4 individual completion interrupt 358 EDMACC_4_TC_7_INT EDMA3CC4 individual completion interrupt 359 SR_0_PO_VCON_SMPSERR_INT SmartReflex SMPS Error interrupt 360 SR_0_SMARTREFLEX_INTREQ0 SmartReflex controller interrupt 361 SR_0_SMARTREFLEX_INTREQ1 SmartReflex controller interrupt 362 SR_0_SMARTREFLEX_INTREQ2 SmartReflex controller interrupt 363 SR_0_SMARTREFLEX_INTREQ3 SmartReflex controller interrupt 364 SR_0_VPNOSMPSACK SmartReflex VPVOLTUPDATE has been asserted but SMPS has not been responded to in a defined time interval 365 SR_0_VPEQVALUE SmartReflex SRSINTERUPT is asserted, but the new voltage is not different from the current SMPS voltage 366 SR_0_VPMAXVDD SmartReflex The new voltage required is equal to or greater than MaxVdd 367 SR_0_VPMINVDD SmartReflex The new voltage required is equal to or less than MinVdd 368 SR_0_VPINIDLE SmartReflex. Indicating that the FSM of voltage processor is in idle 369 SR_0_VPOPPCHANGEDONE SmartReflex Indicating that the average frequency error is within the desired limit 370 SR_0_VPSMPSACK SmartReflex VPVOLTUPDATE asserted and SMPS has acknowledged in a defined time interval 371 SR_0_SR_TEMPSENSOR SmartReflex temperature threshold crossing interrupt 372 SR_0_SR_TIMERINT SmartReflex internal timer expiration interrupt 373 SR_1_PO_VCON_SMPSERR_INT SmartReflex SMPS Error interrupt 374 SR_1_SMARTREFLEX_INTREQ0 SmartReflex controller interrupt 375 SR_1_SMARTREFLEX_INTREQ1 SmartReflex controller interrupt 376 SR_1_SMARTREFLEX_INTREQ2 SmartReflex controller interrupt 377 SR_1_SMARTREFLEX_INTREQ3 SmartReflex controller interrupt 378 SR_1_VPNOSMPSACK SmartReflex VPVOLTUPDATE has been asserted but SMPS has not been responded to in a defined time interval 379 SR_1_VPEQVALUE SmartReflex SRSINTERUPT is asserted, but the new voltage is not different from the current SMPS voltage 106 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 380 SR_1_VPMAXVDD SmartReflex The new voltage required is equal to or greater than MaxVdd 381 SR_1_VPMINVDD SmartReflex The new voltage required is equal to or less than MinVdd 382 SR_1_VPINIDLE SmartReflex. Indicating that the FSM of voltage processor is in idle 383 SR_1_VPOPPCHANGEDONE SmartReflex Indicating that the average frequency error is within the desired limit 384 SR_1_VPSMPSACK SmartReflex VPVOLTUPDATE asserted and SMPS has acknowledged in a defined time interval 385 SR_1_SR_TEMPSENSOR SmartReflex temperature threshold crossing interrupt 386 SR_1_SR_TIMERINT SmartReflex internal timer expiration interrupt 387 HyperLink_0_INT HyperLink 0 interrupt 388 HyperLink_1_INT HyperLink 1 interrupt 389 ARM_NCTIIRQ0 ARM cross trigger (CTI) IRQ interrupt 390 ARM_NCTIIRQ1 ARM cross trigger (CTI) IRQ interrupt 391 ARM_NCTIIRQ2 ARM cross trigger (CTI) IRQ interrupt 392 ARM_NCTIIRQ3 ARM cross trigger (CTI) IRQ interrupt 393 USB_INT00 USB event ring 0 interrupt 394 USB_INT01 USB event ring 1 interrupt 395 USB_INT02 USB event ring 2 interrupt 396 USB_INT03 USB event ring 3 interrupt 397 USB_INT04 USB event ring 4 interrupt 398 USB_OABSINT USB OABS interrupt 399 USB_MISCINT USB miscellaneous interrupt 400 Reserved Reserved 401 Reserved Reserved 402 10GbE_LINK_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 403 10GbE_USER_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 404 10GbE_LINK_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 405 10GbE_USER_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 406 10GbE_MISC_INT 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 407 10GbE_INT_PKTDMA_0 10 Gigabit Ethernet Packet DMA starvation interrupt (66AK2H14 only) 408 Reserved Reserved 409 Reserved Reserved 410 Reserved Reserved 411 Reserved Reserved 412 Reserved Reserved 413 Reserved Reserved 414 Reserved Reserved 415 Reserved Reserved 416 Reserved Reserved 417 Reserved Reserved 418 Reserved Reserved 419 Reserved Reserved 420 Reserved Reserved 421 Reserved Reserved 422 Reserved Reserved 423 Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 107 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 424 Reserved Reserved 425 Reserved Reserved 426 Reserved Reserved 427 Reserved Reserved 428 Reserved Reserved 429 Reserved Reserved 430 Reserved Reserved 431 Reserved Reserved 432 Reserved Reserved 433 Reserved Reserved 434 Reserved Reserved 435 Reserved Reserved 436 Reserved Reserved 437 Reserved Reserved 438 Reserved Reserved 439 Reserved Reserved 440 Reserved Reserved 441 Reserved Reserved 442 Reserved Reserved 443 Reserved Reserved 444 Reserved Reserved 445 Reserved Reserved 446 Reserved Reserved 447 Reserved Reserved 448 CIC_2_OUT29 CIC2 interrupt 449 CIC_2_OUT30 CIC2 interrupt 450 CIC_2_OUT31 CIC2 interrupt 451 CIC_2_OUT32 CIC2 interrupt 452 CIC_2_OUT33 CIC2 interrupt 453 CIC_2_OUT34 CIC2 interrupt 454 CIC_2_OUT35 CIC2 interrupt 455 CIC_2_OUT36 CIC2 interrupt 456 CIC_2_OUT37 CIC2 interrupt 457 CIC_2_OUT38 CIC2 interrupt 458 CIC_2_OUT39 CIC2 interrupt 459 CIC_2_OUT40 CIC2 interrupt 460 CIC_2_OUT41 CIC2 interrupt 461 CIC_2_OUT42 CIC2 interrupt 462 CIC_2_OUT43 CIC2 interrupt 463 CIC_2_OUT44 CIC2 interrupt 464 CIC_2_OUT45 CIC2 interrupt 465 CIC_2_OUT46 CIC2 interrupt 466 CIC_2_OUT47 CIC2 interrupt 467 CIC_2_OUT18 CIC2 interrupt 468 CIC_2_OUT19 CIC2 interrupt 469 CIC_2_OUT22 CIC2 interrupt 470 CIC_2_OUT23 CIC2 interrupt 108 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-23. System Event Mapping — ARM CorePac Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 471 CIC_2_OUT50 CIC2 interrupt 472 CIC_2_OUT51 CIC2 interrupt 473 CIC_2_OUT66 CIC2 interrupt 474 CIC_2_OUT67 CIC2 interrupt 475 CIC_2_OUT88 CIC2 interrupt 476 CIC_2_OUT89 CIC2 interrupt 477 CIC_2_OUT90 CIC2 interrupt 478 CIC_2_OUT91 CIC2 interrupt 479 CIC_2_OUT92 CIC2 interrupt Table 8-24, Table 8-25, and Table 8-26 list the C66x CorePac Secondary interrupt inputs. Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts EVENT NO. EVENT NAME DESCRIPTION 0 EDMACC_1_ERRINT EDMA3CC1 error interrupt 1 EDMACC_1_MPINT EDMA3CC1 memory protection interrupt 2 EDMACC_1_TC_0_ERRINT EDMA3CC1 TPTC0 error interrupt 3 EDMACC_1_TC_1_ERRINT EDMA3CC1 TPTC1 error interrupt 4 EDMACC_1_TC_2_ERRINT EDMA3CC1 TPTC2 error interrupt 5 EDMACC_1_TC_3_ERRINT EDMA3CC1 TPTC3 error interrupt 6 EDMACC_1_GINT EDMA3CC1 GINT 7 Reserved Reserved 8 EDMACC_1_TC_0_INT EDMA3CC1 individual completion interrupt 9 EDMACC_1_TC_1_INT EDMA3CC1 individual completion interrupt 10 EDMACC_1_TC_2_INT EDMA3CC1 individual completion interrupt 11 EDMACC_1_TC_3_INT EDMA3CC1 individual completion interrupt 12 EDMACC_1_TC_4_INT EDMA3CC1 individual completion interrupt 13 EDMACC_1_TC_5_INT EDMA3CC1 individual completion interrupt 14 EDMACC_1_TC_6_INT EDMA3CC1 individual completion interrupt 15 EDMACC_1_TC_7_INT EDMA3CC1 individual completion interrupt 16 EDMACC_2_ERRINT EDMA3CC2 error interrupt 17 EDMACC_2_MPINT EDMA3CC2 memory protection interrupt 18 EDMACC_2_TC_0_ERRINT EDMA3CC2 TPTC0 error interrupt 19 EDMACC_2_TC_1_ERRINT EDMA3CC2 TPTC1 error interrupt 20 EDMACC_2_TC_2_ERRINT EDMA3CC2 TPTC2 error interrupt 21 EDMACC_2_TC_3_ERRINT EDMA3CC2 TPTC3 error interrupt 22 EDMACC_2_GINT EDMA3CC2 GINT 23 Reserved Reserved 24 EDMACC_2_TC_0_INT EDMA3CC2 individual completion interrupt 25 EDMACC_2_TC_1_INT EDMA3CC2 individual completion interrupt 26 EDMACC_2_TC_2_INT EDMA3CC2 individual completion interrupt 27 EDMACC_2_TC_3_INT EDMA3CC2 individual completion interrupt 28 EDMACC_2_TC_4_INT EDMA3CC2 individual completion interrupt 29 EDMACC_2_TC_5_INT EDMA3CC2 individual completion interrupt 30 EDMACC_2_TC_6_INT EDMA3CC2 individual completion interrupt 31 EDMACC_2_TC_7_INT EDMA3CC2 individual completion interrupt 32 EDMACC_0_ERRINT EDMA3CC0 error interrupt 33 EDMACC_0_MPINT EDMA3CC0 memory protection interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 109 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 34 EDMACC_0_TC_0_ERRINT EDMA3CC0 TPTC0 error interrupt 35 EDMACC_0_TC_1_ERRINT EDMA3CC0 TPTC1 error interrupt 36 EDMACC_0_GINT EDMA3CC0 global completion interrupt 37 Reserved Reserved 38 EDMACC_0_TC_0_INT EDMA3CC0 individual completion interrupt 39 EDMACC_0_TC_1_INT EDMA3CC0 individual completion interrupt 40 EDMACC_0_TC_2_INT EDMA3CC0 individual completion interrupt 41 EDMACC_0_TC_3_INT EDMA3CC0 individual completion interrupt 42 EDMACC_0_TC_4_INT EDMA3CC0 individual completion interrupt 43 EDMACC_0_TC_5_INT EDMA3CC0 individual completion interrupt 44 EDMACC_0_TC_6_INT EDMA3CC0 individual completion interrupt 45 EDMACC_0_TC_7_INT EDMA3CC0 individual completion interrupt 46 Reserved Reserved 47 QMSS_QUE_PEND_652 Navigator transmit queue pending event for indicated queue 48 PCIE_INT12 PCIE protocol error interrupt 49 PCIE_INT13 PCIE power management interrupt 50 PCIE_INT0 PCIE legacy INTA interrupt 51 PCIE_INT1 PCIE legacy INTB interrupt 52 PCIE_INT2 PCIE legacy INTC interrupt 53 PCIE_INT3 PCIE legacy INTD interrupt 54 SPI_0_INT0 SPI0 interrupt0 55 SPI_0_INT1 SPI0 interrupt1 56 SPI_0_XEVT SPI0 transmit event 57 SPI_0_REVT SPI0 receive event 58 I2C_0_INT I2C0 interrupt 59 I2C_0_REVT I2C0 receive event 60 I2C_0_XEVT I2C0 transmit event 61 Reserved Reserved 62 Reserved Reserved 63 DBGTBR_DMAINT Debug trace buffer (TBR) DMA event 64 MPU_12_INT MPU12 addressing violation interrupt and protection violation interrupt 65 DBGTBR_ACQCOMP Debug trace buffer (TBR) acquisition has been completed 66 MPU_13_INT MPU13 addressing violation interrupt and protection violation interrupt 67 MPU_14_INT MPU14 addressing violation interrupt and protection violation interrupt 68 NETCP_MDIO_LINK_INT0 Packet Accelerator 0 subsystem MDIO interrupt 69 NETCP_MDIO_LINK_INT1 Packet Accelerator 0 subsystem MDIO interrupt 70 NETCP_MDIO_USER_INT0 Packet Accelerator 0 subsystem MDIO interrupt 71 NETCP_MDIO_USER_INT1 Packet Accelerator 0 subsystem MDIO interrupt 72 NETCP_MISC_INT Packet Accelerator 0 subsystem misc interrupt 73 TRACER_CORE_0_INT Tracer sliding time window interrupt for DSP0 L2 74 TRACER_CORE_1_INT Tracer sliding time window interrupt for DSP1 L2 75 TRACER_CORE_2_INT Tracer sliding time window interrupt for DSP2 L2 76 TRACER_CORE_3_INT Tracer sliding time window interrupt for DSP3 L2 77 TRACER_DDR_INT Tracer sliding time window interrupt for MSMC-DDR3A 78 TRACER_MSMC_0_INT Tracer sliding time window interrupt for MSMC SRAM bank0 79 TRACER_MSMC_1_INT Tracer sliding time window interrupt for MSMC SRAM bank1 80 TRACER_MSMC_2_INT Tracer sliding time window interrupt for MSMC SRAM bank2 110 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 81 TRACER_MSMC_3_INT Tracer sliding time window interrupt for MSMC SRAM bank3 82 TRACER_CFG_INT Tracer sliding time window interrupt for CFG0 TeraNet 83 TRACER_QMSS_QM_CFG1_INT Tracer sliding time window interrupt for Navigator CFG1 slave port 84 TRACER_QMSS_DMA_INT Tracer sliding time window interrupt for Navigator DMA internal bus slave port 85 TRACER_SEM_INT Tracer sliding time window interrupt for Semaphore 86 PSC_ALLINT Power & Sleep Controller interrupt 87 MSMC_SCRUB_CERROR Correctable (1-bit) soft error detected during scrub cycle 88 BOOTCFG_INT Chip-level MMR Error Register 89 SR_0_PO_VCON_SMPSERR_INT SmartReflex SMPS error interrupt 90 MPU_0_INT MPU0 addressing violation interrupt and protection violation interrupt 91 QMSS_QUE_PEND_653 Navigator transmit queue pending event for indicated queue 92 MPU_1_INT MPU1 addressing violation interrupt and protection violation interrupt. 93 QMSS_QUE_PEND_654 Navigator transmit queue pending event for indicated queue 94 MPU_2_INT MPU2 addressing violation interrupt and protection violation interrupt. 95 QMSS_QUE_PEND_655 Navigator transmit queue pending event for indicated queue 96 MPU_3_INT MPU3 addressing violation interrupt and protection violation interrupt. 97 QMSS_QUE_PEND_656 Navigator transmit queue pending event for indicated queue 98 MSMC_DEDC_CERROR Correctable (1-bit) soft error detected on SRAM read 99 MSMC_DEDC_NC_ERROR Noncorrectable (2-bit) soft error detected on SRAM read 100 MSMC_SCRUB_NC_ERROR Noncorrectable (2-bit) soft error detected during scrub cycle 101 MSMC_MPF_ERROR0 Memory protection fault indicators for system master PrivID = 0 102 MSMC_MPF_ERROR8 Memory protection fault indicators for system master PrivID = 8 103 MSMC_MPF_ERROR9 Memory protection fault indicators for system master PrivID = 9 104 MSMC_MPF_ERROR10 Memory protection fault indicators for system master PrivID = 10 105 MSMC_MPF_ERROR11 Memory protection fault indicators for system master PrivID = 11 106 MSMC_MPF_ERROR12 Memory protection fault indicators for system master PrivID = 12 107 MSMC_MPF_ERROR13 Memory protection fault indicators for system master PrivID = 13 108 MSMC_MPF_ERROR14 Memory protection fault indicators for system master PrivID = 14 109 MSMC_MPF_ERROR15 Memory protection fault indicators for system master PrivID = 15 110 DDR3_0_ERR DDR3A_EMIF error interrupt 111 HYPERLINK_0_INT HyperLink 0 interrupt 112 SRIO_INTDST0 SRIO interrupt 113 SRIO_INTDST1 SRIO interrupt 114 SRIO_INTDST2 SRIO interrupt 115 SRIO_INTDST3 SRIO interrupt 116 SRIO_INTDST4 SRIO interrupt 117 SRIO_INTDST5 SRIO interrupt 118 SRIO_INTDST6 SRIO interrupt 119 SRIO_INTDST7 SRIO interrupt 120 SRIO_INTDST8 SRIO interrupt 121 SRIO_INTDST9 SRIO interrupt 122 SRIO_INTDST10 SRIO interrupt 123 SRIO_INTDST11 SRIO interrupt 124 SRIO_INTDST12 SRIO interrupt 125 SRIO_INTDST13 SRIO interrupt 126 SRIO_INTDST14 SRIO interrupt 127 SRIO_INTDST15 SRIO interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 111 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 128 AEMIF_EASYNCERR Asynchronous EMIF16 error interrupt 129 TRACER_CORE_4_INT Tracer sliding time window interrupt for DSP4 L2 130 TRACER_CORE_5_INT Tracer sliding time window interrupt for DSP5 L2 131 TRACER_CORE_6_INT Tracer sliding time window interrupt for DSP6 L2 132 TRACER_CORE_7_INT Tracer sliding time window interrupt for DSP7 L2 133 QMSS_INTD_1_PKTDMA_0 Navigator interrupt for Packet DMA starvation 134 QMSS_INTD_1_PKTDMA_1 Navigator interrupt for Packet DMA starvation 135 SRIO_INT_PKTDMA_0 IPC interrupt generation 136 NETCP_PKTDMA_INT0 Packet Accelerator0 Packet DMA starvation interrupt 137 SR_0_SMARTREFLEX_INTREQ0 SmartReflex controller interrupt 138 SR_0_SMARTREFLEX_INTREQ1 SmartReflex controller interrupt 139 SR_0_SMARTREFLEX_INTREQ2 SmartReflex controller interrupt 140 SR_0_SMARTREFLEX_INTREQ3 SmartReflex controller interrupt 141 SR_0_VPNOSMPSACK SmartReflex VPVOLTUPDATE has been asserted but SMPS has not been responded to in a defined time interval 142 SR_0_VPEQVALUE SmartReflex SRSINTERUPT is asserted, but the new voltage is not different from the current SMPS voltage 143 SR_0_VPMAXVDD SmartReflex. The new voltage required is equal to or greater than MaxVdd 144 SR_0_VPMINVDD SmartReflex. The new voltage required is equal to or less than MinVdd 145 SR_0_VPINIDLE SmartReflex indicating that the FSM of voltage processor is in idle 146 SR_0_VPOPPCHANGEDONE SmartReflex indicating that the average frequency error is within the desired limit 147 Reserved Reserved 148 UART_0_UARTINT UART0 interrupt 149 UART_0_URXEVT UART0 receive event 150 UART_0_UTXEVT UART0 transmit event 151 QMSS_QUE_PEND_657 Navigator transmit queue pending event for indicated queue 152 QMSS_QUE_PEND_658 Navigator transmit queue pending event for indicated queue 153 QMSS_QUE_PEND_659 Navigator transmit queue pending event for indicated queue 154 QMSS_QUE_PEND_660 Navigator transmit queue pending event for indicated queue 155 QMSS_QUE_PEND_661 Navigator transmit queue pending event for indicated queue 156 QMSS_QUE_PEND_662 Navigator transmit queue pending event for indicated queue 157 QMSS_QUE_PEND_663 Navigator transmit queue pending event for indicated queue 158 QMSS_QUE_PEND_664 Navigator transmit queue pending event for indicated queue 159 QMSS_QUE_PEND_665 Navigator transmit queue pending event for indicated queue 160 SR_0_VPSMPSACK SmartReflex VPVOLTUPDATE asserted and SMPS has acknowledged in a defined time interval 161 ARM_TBR_DMA ARM trace buffer (TBR) DMA event 162 ARM_TBR_ACQ ARM trace buffer (TBR) acquisition has been completed 163 ARM_NINTERRIRQ ARM internal memory ECC error interrupt request 164 ARM_NAXIERRIRQ ARM bus error interrupt request 165 SR_0_SR_TEMPSENSOR SmartReflex temperature threshold crossing interrupt 166 SR_0_SR_TIMERINT SmartReflex internal timer expiration interrupt 167 Reserved Reserved 168 Reserved Reserved 169 Reserved Reserved 170 Reserved Reserved 171 Reserved Reserved 112 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 172 Reserved Reserved 173 Reserved Reserved 174 Reserved Reserved 175 TIMER_7_INTL Timer interrupt low (1) 176 TIMER_7_INTH Timer interrupt high (1) 177 TIMER_6_INTL Timer interrupt low (1) 178 TIMER_6_INTH Timer interrupt high (1) 179 TIMER_5_INTL Timer interrupt low (1) 180 TIMER_5_INTH Timer interrupt high (1) 181 TIMER_4_INTL Timer interrupt low (1) 182 TIMER_4_INTH Timer interrupt high (1) 183 TIMER_3_INTL Timer interrupt low 184 TIMER_3_INTH Timer interrupt high 185 TIMER_2_INTL Timer interrupt low 186 TIMER_2_INTH Timer interrupt high 187 TIMER_1_INTL Timer interrupt low 188 TIMER_1_INTH Timer interrupt high 189 TIMER_0_INTL Timer interrupt low 190 TIMER_0_INTH Timer interrupt high 191 Reserved Reserved 192 Reserved Reserved 193 Reserved Reserved 194 Reserved Reserved 195 Reserved Reserved 196 Reserved Reserved 197 Reserved Reserved 198 Reserved Reserved 199 Reserved Reserved 200 Reserved Reserved 201 Reserved Reserved 202 Reserved Reserved 203 Reserved Reserved 204 Reserved Reserved 205 Reserved Reserved 206 Reserved Reserved 207 EDMACC_4_ERRINT EDMA3CC4 error interrupt 208 EDMACC_4_MPINT EDMA3CC4 memory protection interrupt 209 EDMACC_4_TC_0_ERRINT EDMA3CC4 TPTC0 error interrupt 210 EDMACC_4_TC_1_ERRINT EDMA3CC4 TPTC1 error interrupt 211 EDMACC_4_GINT EDMA3CC4 GINT 212 EDMACC_4_TC_0_INT EDMA3CC4 individual completion interrupt 213 EDMACC_4_TC_1_INT EDMA3CC4 individual completion interrupt 214 EDMACC_4_TC_2_INT EDMA3CC4 individual completion interrupt 215 EDMACC_4_TC_3_INT EDMA3CC4 individual completion interrupt 216 EDMACC_4_TC_4_INT EDMA3CC4 individual completion interrupt 217 EDMACC_4_TC_5_INT EDMA3CC4 individual completion interrupt (1) 66AK2H12/14 only. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 113 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 218 EDMACC_4_TC_6_INT EDMA3CC4 individual completion interrupt 219 EDMACC_4_TC_7_INT EDMA3CC4 individual completion interrupt 220 EDMACC_3_ERRINT EDMA3CC3 error interrupt 221 EDMACC_3_MPINT EDMA3CC3 memory protection interrupt 222 EDMACC_3_TC_0_ERRINT EDMA3CC3 TPTC0 error interrupt 223 EDMACC_3_TC_1_ERRINT EDMA3CC3 TPTC1 error interrupt 224 EDMACC_3_GINT EDMA3CC3 GINT 225 EDMACC_3_TC_0_INT EDMA3CC3 individual completion interrupt 226 EDMACC_3_TC_1_INT EDMA3CC3 individual completion interrupt 227 EDMACC_3_TC_2_INT EDMA3CC3 individual completion interrupt 228 EDMACC_3_TC_3_INT EDMA3CC3 individual completion interrupt 229 EDMACC_3_TC_4_INT EDMA3CC3 individual completion interrupt 230 EDMACC_3_TC_5_INT EDMA3CC3 individual completion interrupt 231 EDMACC_3_TC_6_INT EDMA3CC3 individual completion interrupt 232 EDMACC_3_TC_7_INT EDMA3CC3 individual completion interrupt 233 UART_1_UARTINT UART1 interrupt 234 UART_1_URXEVT UART1 receive event 235 UART_1_UTXEVT UART1 transmit event 236 I2C_1_INT I2C1 interrupt 237 I2C_1_REVT I2C1 receive event 238 I2C_1_XEVT I2C1 transmit event 239 SPI_1_INT0 SPI1 interrupt0 240 SPI_1_INT1 SPI1 interrupt1 241 SPI_1_XEVT SPI1 transmit event 242 SPI_1_REVT SPI1 receive event 243 MPU_5_INT MPU5 addressing violation interrupt and protection violation interrupt 244 MPU_8_INT MPU8 addressing violation interrupt and protection violation interrupt 245 MPU_9_INT MPU9 addressing violation interrupt and protection violation interrupt 246 MPU_11_INT MPU11 addressing violation interrupt and protection violation interrupt 247 MPU_4_INT MPU4 addressing violation interrupt and protection violation interrupt 248 MPU_6_INT MPU6 addressing violation interrupt and protection violation interrupt 249 MPU_7_INT MPU7 addressing violation interrupt and protection violation interrupt 250 MPU_10_INT MPU10 addressing violation interrupt and protection violation interrupt 251 SPI_2_INT0 SPI2 interrupt0 252 SPI_2_INT1 SPI2 interrupt1 253 SPI_2_XEVT SPI2 transmit event 254 SPI_2_REVT SPI2 receive event 255 I2C_2_INT I2C2 interrupt 256 I2C_2_REVT I2C2 receive event 257 I2C_2_XEVT I2C2 transmit event 258 Reserved Reserved 259 Reserved Reserved 260 Reserved Reserved 261 Reserved Reserved 262 Reserved Reserved 263 Reserved Reserved 264 Reserved Reserved 114 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 265 Reserved Reserved 266 Reserved Reserved 267 Reserved Reserved 268 Reserved Reserved 269 Reserved Reserved 270 Reserved Reserved 271 Reserved Reserved 272 Reserved Reserved 273 Reserved Reserved 274 Reserved Reserved 275 Reserved Reserved 276 Reserved Reserved 277 Reserved Reserved 278 Reserved Reserved 279 Reserved Reserved 280 Reserved Reserved 281 Reserved Reserved 282 Reserved Reserved 283 Reserved Reserved 284 Reserved Reserved 285 Reserved Reserved 286 Reserved Reserved 287 Reserved Reserved 288 Reserved Reserved 289 Reserved Reserved 290 Reserved Reserved 291 Reserved Reserved 292 QMSS_QUE_PEND_666 Navigator transmit queue pending event for indicated queue 293 QMSS_QUE_PEND_667 Navigator transmit queue pending event for indicated queue 294 QMSS_QUE_PEND_668 Navigator transmit queue pending event for indicated queue 295 QMSS_QUE_PEND_669 Navigator transmit queue pending event for indicated queue 296 QMSS_QUE_PEND_670 Navigator transmit queue pending event for indicated queue 297 QMSS_QUE_PEND_671 Navigator transmit queue pending event for indicated queue 298 QMSS_QUE_PEND_8844 Navigator transmit queue pending event for indicated queue 299 QMSS_QUE_PEND_8845 Navigator transmit queue pending event for indicated queue 300 QMSS_QUE_PEND_8846 Navigator transmit queue pending event for indicated queue 301 QMSS_QUE_PEND_8847 Navigator transmit queue pending event for indicated queue 302 QMSS_QUE_PEND_8848 Navigator transmit queue pending event for indicated queue 303 QMSS_QUE_PEND_8849 Navigator transmit queue pending event for indicated queue 304 QMSS_QUE_PEND_8850 Navigator transmit queue pending event for indicated queue 305 QMSS_QUE_PEND_8851 Navigator transmit queue pending event for indicated queue 306 QMSS_QUE_PEND_8852 Navigator transmit queue pending event for indicated queue 307 QMSS_QUE_PEND_8853 Navigator transmit queue pending event for indicated queue 308 QMSS_QUE_PEND_8854 Navigator transmit queue pending event for indicated queue 309 QMSS_QUE_PEND_8855 Navigator transmit queue pending event for indicated queue 310 QMSS_QUE_PEND_8856 Navigator transmit queue pending event for indicated queue 311 QMSS_QUE_PEND_8857 Navigator transmit queue pending event for indicated queue Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 115 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 312 QMSS_QUE_PEND_8858 Navigator transmit queue pending event for indicated queue 313 QMSS_QUE_PEND_8859 Navigator transmit queue pending event for indicated queue 314 QMSS_QUE_PEND_8860 Navigator transmit queue pending event for indicated queue 315 QMSS_QUE_PEND_8861 Navigator transmit queue pending event for indicated queue 316 QMSS_QUE_PEND_8862 Navigator transmit queue pending event for indicated queue 317 QMSS_QUE_PEND_8863 Navigator transmit queue pending event for indicated queue 318 QMSS_INTD_2_PKTDMA_0 Navigator ECC error interrupt 319 QMSS_INTD_2_PKTDMA_1 Navigator ECC error interrupt 320 QMSS_INTD_1_LOW_0 Navigator interrupt low 321 QMSS_INTD_1_LOW_1 Navigator interrupt low 322 QMSS_INTD_1_LOW_2 Navigator interrupt low 323 QMSS_INTD_1_LOW_3 Navigator interrupt low 324 QMSS_INTD_1_LOW_4 Navigator interrupt low 325 QMSS_INTD_1_LOW_5 Navigator interrupt low 326 QMSS_INTD_1_LOW_6 Navigator interrupt low 327 QMSS_INTD_1_LOW_7 Navigator interrupt low 328 QMSS_INTD_1_LOW_8 Navigator interrupt low 329 QMSS_INTD_1_LOW_9 Navigator interrupt low 330 QMSS_INTD_1_LOW_10 Navigator interrupt low 331 QMSS_INTD_1_LOW_11 Navigator interrupt low 332 QMSS_INTD_1_LOW_12 Navigator interrupt low 333 QMSS_INTD_1_LOW_13 Navigator interrupt low 334 QMSS_INTD_1_LOW_14 Navigator interrupt low 335 QMSS_INTD_1_LOW_15 Navigator interrupt low 336 QMSS_INTD_2_LOW_0 Navigator second interrupt low 337 QMSS_INTD_2_LOW_1 Navigator second interrupt low 338 QMSS_INTD_2_LOW_2 Navigator second interrupt low 339 QMSS_INTD_2_LOW_3 Navigator second interrupt low 340 QMSS_INTD_2_LOW_4 Navigator second interrupt low 341 QMSS_INTD_2_LOW_5 Navigator second interrupt low 342 QMSS_INTD_2_LOW_6 Navigator second interrupt low 343 QMSS_INTD_2_LOW_7 Navigator second interrupt low 344 QMSS_INTD_2_LOW_8 Navigator second interrupt low 345 QMSS_INTD_2_LOW_9 Navigator second interrupt low 346 QMSS_INTD_2_LOW_10 Navigator second interrupt low 347 QMSS_INTD_2_LOW_11 Navigator second interrupt low 348 QMSS_INTD_2_LOW_12 Navigator second interrupt low 349 QMSS_INTD_2_LOW_13 Navigator second interrupt low 350 QMSS_INTD_2_LOW_14 Navigator second interrupt low 351 QMSS_INTD_2_LOW_15 Navigator second interrupt low 352 TRACER_EDMACC_0 Tracer sliding time window interrupt for EDMA3CC0 353 TRACER_EDMACC_123_INT Tracer sliding time window interrupt for EDMA3CC1, EDMA3CC2 and EDMA3CC3 354 TRACER_CIC_INT Tracer sliding time window interrupt for interrupt controllers (CIC) 355 TRACER_MSMC_4_INT Tracer sliding time window interrupt for MSMC SRAM bank4 356 TRACER_MSMC_5_INT Tracer sliding time window interrupt for MSMC SRAM bank5 357 TRACER_MSMC_6_INT Tracer sliding time window interrupt for MSMC SRAM bank6 358 TRACER_MSMC_7_INT Tracer sliding time window interrupt for MSMC SRAM bank7 116 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 359 TRACER_SPI_ROM_EMIF_INT Tracer sliding time window interrupt for SPI/ROM/EMIF16 modules 360 TRACER_QMSS_QM_CFG2_INT Tracer sliding time window interrupt for QM2 361 Reserved Reserved 362 Reserved Reserved 363 TRACER_DDR_1_INT Tracer sliding time window interrupt for DDR3B 364 Reserved Reserved 365 HYPERLINK_1_INT HyperLink 1 interrupt 366 Reserved Reserved 367 Reserved Reserved 368 Reserved Reserved 369 Reserved Reserved 370 Reserved Reserved 371 Reserved Reserved 372 Reserved Reserved 373 Reserved Reserved 374 Reserved Reserved 375 Reserved Reserved 376 Reserved Reserved 377 Reserved Reserved 378 Reserved Reserved 379 Reserved Reserved 380 Reserved Reserved 381 Reserved Reserved 382 Reserved Reserved 383 Reserved Reserved 384 Reserved Reserved 385 Reserved Reserved 386 Reserved Reserved 387 Reserved Reserved 388 Reserved Reserved 389 Reserved Reserved 390 Reserved Reserved 391 Reserved Reserved 392 Reserved Reserved 393 Reserved Reserved 394 Reserved Reserved 395 Reserved Reserved 396 Reserved Reserved 397 Reserved Reserved 398 Reserved Reserved 399 Reserved Reserved 400 Reserved Reserved 401 Reserved Reserved 402 Reserved Reserved 403 Reserved Reserved 404 Reserved Reserved 405 Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 117 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 406 Reserved Reserved 407 Reserved Reserved 408 Reserved Reserved 409 Reserved Reserved 410 Reserved Reserved 411 Reserved Reserved 412 Reserved Reserved 413 Reserved Reserved 414 Reserved Reserved 415 Reserved Reserved 416 Reserved Reserved 417 Reserved Reserved 418 Reserved Reserved 419 Reserved Reserved 420 Reserved Reserved 421 Reserved Reserved 422 USB_INT00 USB interrupt 423 USB_INT04 USB interrupt 424 USB_INT05 USB interrupt 425 USB_INT06 USB interrupt 426 USB_INT07 USB interrupt 427 USB_INT08 USB interrupt 428 USB_INT09 USB interrupt 429 USB_INT10 USB interrupt 430 USB_INT11 USB interrupt 431 USB_MISCINT USB miscellaneous interrupt 432 USB_OABSINT USB OABS interrupt 433 TIMER_12_INTL Timer interrupt low 434 TIMER_12_INTH Timer interrupt high 435 TIMER_13_INTL Timer interrupt low 436 TIMER_13_INTH Timer interrupt high 437 TIMER_14_INTL Timer interrupt low 438 TIMER_14_INTH Timer interrupt high 439 TIMER_15_INTL Timer interrupt low 440 TIMER_15_INTH Timer interrupt high 441 TIMER_16_INTL Timer interrupt low 442 TIMER_17_INTL Timer interrupt high 443 TIMER_18_INTL Timer interrupt low (1) 444 TIMER_19_INTL Timer interrupt high (1) 445 DDR3_1_ERR DDR3B_EMIF error interrupt 446 GPIO_INT16 GPIO interrupt 447 GPIO_INT17 GPIO interrupt 448 GPIO_INT18 GPIO interrupt 449 GPIO_INT19 GPIO interrupt 450 GPIO_INT20 GPIO interrupt 451 GPIO_INT21 GPIO interrupt 452 GPIO_INT22 GPIO interrupt 118 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-24. CIC0 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 453 GPIO_INT23 GPIO interrupt 454 GPIO_INT24 GPIO interrupt 455 GPIO_INT25 GPIO interrupt 456 GPIO_INT26 GPIO interrupt 457 GPIO_INT27 GPIO interrupt 458 GPIO_INT28 GPIO interrupt 459 GPIO_INT29 GPIO interrupt 460 GPIO_INT30 GPIO interrupt 461 GPIO_INT31 GPIO interrupt 462 SRIO_INTDST16 SRIOI interrupt 463 SRIO_INTDST17 SRIOI interrupt 464 SRIO_INTDST18 SRIOI interrupt 465 SRIO_INTDST19 SRIOI interrupt 466 PCIE_INT4 PCIE MSI interrupt 467 PCIE_INT5 PCIE MSI interrupt 468 PCIE_INT6 PCIE MSI interrupt 469 PCIE_INT7 PCIE MSI interrupt 470 SEM_INT12 Semaphore interrupt 471 SEM_INT13 Semaphore interrupt 472 SEM_ERR12 Semaphore error interrupt 473 SEM_ERR13 Semaphore error interrupt Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts EVENT NO. EVENT NAME DESCRIPTION 0 EDMACC_1_ERRINT EDMA3CC1 error interrupt 1 EDMACC_1_MPINT EDMA3CC1 memory protection interrupt 2 EDMACC_1_TC_0_ERRINT EDMA3CC1 TPTC0 error interrupt 3 EDMACC_1_TC_1_ERRINT EDMA3CC1 TPTC1 error interrupt 4 EDMACC_1_TC_2_ERRINT EDMA3CC1 TPTC2 error interrupt 5 EDMACC_1_TC_3_ERRINT EDMA3CC1 TPTC3 error interrupt 6 EDMACC_1_GINT EDMA3CC1 GINT 7 Reserved Reserved 8 EDMACC_1_TC_0_INT EDMA3CC1 individual completion interrupt 9 EDMACC_1_TC_1_INT EDMA3CC1 individual completion interrupt 10 EDMACC_1_TC_2_INT EDMA3CC1 individual completion interrupt 11 EDMACC_1_TC_3_INT EDMA3CC1 individual completion interrupt 12 EDMACC_1_TC_4_INT EDMA3CC1 individual completion interrupt 13 EDMACC_1_TC_5_INT EDMA3CC1 individual completion interrupt 14 EDMACC_1_TC_6_INT EDMA3CC1 individual completion interrupt 15 EDMACC_1_TC_7_INT EDMA3CC1 individual completion interrupt 16 EDMACC_2_ERRINT EDMA3CC2 error interrupt 17 EDMACC_2_MPINT EDMA3CC2 memory protection interrupt 18 EDMACC_2_TC_0_ERRINT EDMA3CC2 TPTC0 error interrupt 19 EDMACC_2_TC_1_ERRINT EDMA3CC2 TPTC1 error interrupt 20 EDMACC_2_TC_2_ERRINT EDMA3CC2 TPTC2 error interrupt 21 EDMACC_2_TC_3_ERRINT EDMA3CC2 TPTC3 error interrupt 22 EDMACC_2_GINT EDMA3CC2 GINT Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 119 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 23 Reserved Reserved 24 EDMACC_2_TC_0_INT EDMA3CC2 individual completion interrupt 25 EDMACC_2_TC_1_INT EDMA3CC2 individual completion interrupt 26 EDMACC_2_TC_2_INT EDMA3CC2 individual completion interrupt 27 EDMACC_2_TC_3_INT EDMA3CC2 individual completion interrupt 28 EDMACC_2_TC_4_INT EDMA3CC2 individual completion interrupt 29 EDMACC_2_TC_5_INT EDMA3CC2 individual completion interrupt 30 EDMACC_2_TC_6_INT EDMA3CC2 individual completion interrupt 31 EDMACC_2_TC_7_INT EDMA3CC2 individual completion interrupt 32 EDMACC_0_ERRINT EDMA3CC0 error interrupt 33 EDMACC_0_MPINT EDMA3CC0 memory protection interrupt 34 EDMACC_0_TC_0_ERRINT EDMA3CC0 TPTC0 error interrupt 35 EDMACC_0_TC_1_ERRINT EDMA3CC0 TPTC1 error interrupt 36 EDMACC_0_GINT EDMA3CC0 GINT 37 Reserved Reserved 38 EDMACC_0_TC_0_INT EDMA3CC0 individual completion interrupt 39 EDMACC_0_TC_1_INT EDMA3CC0 individual completion interrupt 40 EDMACC_0_TC_2_INT EDMA3CC0 individual completion interrupt 41 EDMACC_0_TC_3_INT EDMA3CC0 individual completion interrupt 42 EDMACC_0_TC_4_INT EDMA3CC0 individual completion interrupt 43 EDMACC_0_TC_5_INT EDMA3CC0 individual completion interrupt 44 EDMACC_0_TC_6_INT EDMA3CC0 individual completion interrupt 45 EDMACC_0_TC_7_INT EDMA3CC0 individual completion interrupt 46 Reserved Reserved 47 QMSS_QUE_PEND_658 Navigator transmit queue pending event for indicated queue 48 PCIE_INT12 PCIE interrupt 49 PCIE_INT13 PCIE interrupt 50 PCIE_INT0 PCIE interrupt 51 PCIE_INT1 PCIE interrupt 52 PCIE_INT2 PCIE interrupt 53 PCIE_INT3 PCIE interrupt 54 SPI_0_INT0 SPI0 interrupt 55 SPI_0_INT1 SPI0 interrupt 56 SPI_0_XEVT SPI0 transmit event 57 SPI_0_REVT SPI0 receive event 58 I2C_0_INT I2C0 interrupt 59 I2C_0_REVT I2C0 receive event 60 I2C_0_XEVT I2C0 transmit event 61 Reserved Reserved 62 Reserved Reserved 63 DBGTBR_DMAINT Debug trace buffer (TBR) DMA event 64 MPU_12_INT MPU12 interrupt 65 DBGTBR_ACQCOMP Debug trace buffer (TBR) acquisition has been completed 66 MPU_13_INT MPU13 interrupt 67 MPU_14_INT MPU14 interrupt 68 NETCP_MDIO_LINK_INT0 Packet Accelerator 0 subsystem MDIO interrupt 69 NETCP_MDIO_LINK_INT1 Packet Accelerator 0 subsystem MDIO interrupt 120 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 70 NETCP_MDIO_USER_INT0 Packet Accelerator 0 subsystem MDIO interrupt 71 NETCP_MDIO_USER_INT1 Packet Accelerator 0 subsystem MDIO interrupt 72 NETCP_MISC_INT Packet Accelerator 0 subsystem misc interrupt 73 TRACER_CORE_0_INT Tracer sliding time window interrupt for DSP0 L2 74 TRACER_CORE_1_INT Tracer sliding time window interrupt for DSP1 L2 75 TRACER_CORE_2_INT Tracer sliding time window interrupt for DSP2 L2 76 TRACER_CORE_3_INT Tracer sliding time window interrupt for DSP3 L2 77 TRACER_DDR_INT Tracer sliding time window interrupt for MSMC-DDR3A 78 TRACER_MSMC_0_INT Tracer sliding time window interrupt for MSMC SRAM bank0 79 TRACER_MSMC_1_INT Tracer sliding time window interrupt for MSMC SRAM bank1 80 TRACER_MSMC_2_INT Tracer sliding time window interrupt for MSMC SRAM bank2 81 TRACER_MSMC_3_INT Tracer sliding time window interrupt for MSMC SRAM bank3 82 TRACER_CFG_INT Tracer sliding time window interrupt for CFG0 TeraNet 83 TRACER_QMSS_QM_CFG1_INT Tracer sliding time window interrupt for Navigator CFG1 slave port 84 TRACER_QMSS_DMA_INT Tracer sliding time window interrupt for Navigator DMA internal bus slave port 85 TRACER_SEM_INT Tracer sliding time window interrupt for Semaphore 86 PSC_ALLINT Power & Sleep Controller interrupt 87 MSMC_SCRUB_CERROR Correctable (1-bit) soft error detected during scrub cycle 88 BOOTCFG_INT Chip-level MMR Error Register 89 SR_0_PO_VCON_SMPSERR_INT SmartReflex SMPS error interrupt 90 MPU_0_INT MPU0 addressing violation interrupt and protection violation interrupt. 91 QMSS_QUE_PEND_659 Navigator transmit queue pending event for indicated queue 92 MPU_1_INT MPU1 addressing violation interrupt and protection violation interrupt. 93 QMSS_QUE_PEND_660 Navigator transmit queue pending event for indicated queue 94 MPU_2_INT MPU2 addressing violation interrupt and protection violation interrupt. 95 QMSS_QUE_PEND_661 Navigator transmit queue pending event for indicated queue 96 MPU_3_INT MPU3 addressing violation interrupt and protection violation interrupt. 97 QMSS_QUE_PEND_662 Navigator transmit queue pending event for indicated queue 98 MSMC_DEDC_CERROR Correctable (1-bit) soft error detected on SRAM read 99 MSMC_DEDC_NC_ERROR Noncorrectable (2-bit) soft error detected on SRAM read 100 MSMC_SCRUB_NC_ERROR Noncorrectable (2-bit) soft error detected during scrub cycle 101 Reserved Reserved 102 MSMC_MPF_ERROR8 Memory protection fault indicators for system master PrivID = 8 103 MSMC_MPF_ERROR9 Memory protection fault indicators for system master PrivID = 9 104 MSMC_MPF_ERROR10 Memory protection fault indicators for system master PrivID = 10 105 MSMC_MPF_ERROR11 Memory protection fault indicators for system master PrivID = 11 106 MSMC_MPF_ERROR12 Memory protection fault indicators for system master PrivID = 12 107 MSMC_MPF_ERROR13 Memory protection fault indicators for system master PrivID = 13 108 MSMC_MPF_ERROR14 Memory protection fault indicators for system master PrivID = 14 109 MSMC_MPF_ERROR15 Memory protection fault indicators for system master PrivID = 15 110 DDR3_0_ERR DDR3A_EMIF Error interrupt 111 HYPERLINK_0_INT HyperLink 0 interrupt 112 SRIO_INTDST0 SRIO interrupt 113 SRIO_INTDST1 SRIO interrupt 114 SRIO_INTDST2 SRIO interrupt 115 SRIO_INTDST3 SRIO interrupt 116 SRIO_INTDST4 SRIO interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 121 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 117 SRIO_INTDST5 SRIO interrupt 118 SRIO_INTDST6 SRIO interrupt 119 SRIO_INTDST7 SRIO interrupt 120 SRIO_INTDST8 SRIO interrupt 121 SRIO_INTDST9 SRIO interrupt 122 SRIO_INTDST10 SRIO interrupt 123 SRIO_INTDST11 SRIO interrupt 124 SRIO_INTDST12 SRIO interrupt 125 SRIO_INTDST13 SRIO interrupt 126 SRIO_INTDST14 SRIO interrupt 127 SRIO_INTDST15 SRIO interrupt 128 AEMIF_EASYNCERR Asynchronous EMIF16 error interrupt 129 TRACER_CORE_4_INT Tracer sliding time window interrupt for DSP4 L2 (1) 130 TRACER_CORE_5_INT Tracer sliding time window interrupt for DSP5 L2 (1) 131 TRACER_CORE_6_INT Tracer sliding time window interrupt for DSP6 L2 (1) 132 TRACER_CORE_7_INT Tracer sliding time window interrupt for DSP7 L2 (1) 133 QMSS_INTD_1_PKTDMA_0 Navigator interrupt for Packet DMA starvation 134 QMSS_INTD_1_PKTDMA_1 Navigator interrupt for Packet DMA starvation 135 SRIO_INT_PKTDMA_0 IPC interrupt generation 136 NETCP_PKTDMA_INT0 Packet Accelerator0 Packet DMA starvation interrupt 137 SR_0_SMARTREFLEX_INTREQ0 SmartReflex controller interrupt 138 SR_0_SMARTREFLEX_INTREQ1 SmartReflex controller interrupt 139 SR_0_SMARTREFLEX_INTREQ2 SmartReflex controller interrupt 140 SR_0_SMARTREFLEX_INTREQ3 SmartReflex controller interrupt 141 SR_0_VPNOSMPSACK SmartReflex VPVOLTUPDATE has been asserted but SMPS has not been responded to in a defined time interval 142 SR_0_VPEQVALUE SmartReflex SRSINTERUPT is asserted, but the new voltage is not different from the current SMPS voltage 143 SR_0_VPMAXVDD SmartReflex. The new voltage required is equal to or greater than MaxVdd 144 SR_0_VPMINVDD SmartReflex. The new voltage required is equal to or less than MinVdd 145 SR_0_VPINIDLE SmartReflex indicating that the FSM of voltage processor is in idle 146 SR_0_VPOPPCHANGEDONE SmartReflex indicating that the average frequency error is within the desired limit 147 Reserved Reserved 148 UART_0_UARTINT UART0 interrupt 149 UART_0_URXEVT UART0 receive event 150 UART_0_UTXEVT UART0 transmit event 151 QMSS_QUE_PEND_663 Navigator transmit queue pending event for indicated queue 152 QMSS_QUE_PEND_664 Navigator transmit queue pending event for indicated queue 153 QMSS_QUE_PEND_665 Navigator transmit queue pending event for indicated queue 154 QMSS_QUE_PEND_666 Navigator transmit queue pending event for indicated queue 155 QMSS_QUE_PEND_667 Navigator transmit queue pending event for indicated queue 156 QMSS_QUE_PEND_668 Navigator transmit queue pending event for indicated queue 157 QMSS_QUE_PEND_669 Navigator transmit queue pending event for indicated queue 158 QMSS_QUE_PEND_670 Navigator transmit queue pending event for indicated queue 159 QMSS_QUE_PEND_671 Navigator transmit queue pending event for indicated queue 160 SR_0_VPSMPSACK SmartReflex VPVOLTUPDATE asserted and SMPS has acknowledged in a defined time interval (1) 122 66AK2H12/14 only. Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 161 ARM_TBR_DMA ARM trace buffer (TBR) DMA event 162 ARM_TBR_ACQ ARM trace buffer (TBR) Acquisition has been completed 163 ARM_NINTERRIRQ ARM internal memory ECC error interrupt request 164 ARM_NAXIERRIRQ ARM bus error interrupt request 165 SR_0_SR_TEMPSENSOR SmartReflex temperature threshold crossing interrupt 166 SR_0_SR_TIMERINT SmartReflex internal timer expiration interrupt 167 Reserved Reserved 168 Reserved Reserved 169 Reserved Reserved 170 Reserved Reserved 171 Reserved Reserved 172 Reserved Reserved 173 Reserved Reserved 174 Reserved Reserved 175 TIMER_7_INTL Timer interrupt low (1) 176 TIMER_7_INTH Timer interrupt high (1) 177 TIMER_6_INTL Timer interrupt low (1) 178 TIMER_6_INTH Timer interrupt high (1) 179 TIMER_5_INTL Timer interrupt low (1) 180 TIMER_5_INTH Timer interrupt high (1) 181 TIMER_4_INTL Timer interrupt low (1) 182 TIMER_4_INTH Timer interrupt high (1) 183 TIMER_3_INTL Timer interrupt low 184 TIMER_3_INTH Timer interrupt high 185 TIMER_2_INTL Timer interrupt low 186 TIMER_2_INTH Timer interrupt high 187 TIMER_1_INTL Timer interrupt low 188 TIMER_1_INTH Timer interrupt high 189 TIMER_0_INTL Timer interrupt low 190 TIMER_0_INTH Timer interrupt high 191 Reserved Reserved 192 Reserved Reserved 193 Reserved Reserved 194 Reserved Reserved 195 Reserved Reserved 196 Reserved Reserved 197 Reserved Reserved 198 Reserved Reserved 199 Reserved Reserved 200 Reserved Reserved 201 Reserved Reserved 202 Reserved Reserved 203 Reserved Reserved 204 Reserved Reserved 205 Reserved Reserved 206 Reserved Reserved 207 EDMACC_4_ERRINT EDMA3CC4 error interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 123 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 208 EDMACC_4_MPINT EDMA3CC4 memory protection interrupt 209 EDMACC_4_TC_0_ERRINT EDMA3CC4 TPTC0 error interrupt 210 EDMACC_4_TC_1_ERRINT EDMA3CC4 TPTC1 error interrupt 211 EDMACC_4_GINT EDMA3CC4 GINT 212 EDMACC_4_TC_0_INT EDMA3CC4 individual completion interrupt 213 EDMACC_4_TC_1_INT EDMA3CC4 individual completion interrupt 214 EDMACC_4_TC_2_INT EDMA3CC4 individual completion interrupt 215 EDMACC_4_TC_3_INT EDMA3CC4 individual completion interrupt 216 EDMACC_4_TC_4_INT EDMA3CC4 individual completion interrupt 217 EDMACC_4_TC_5_INT EDMA3CC4 individual completion interrupt 218 EDMACC_4_TC_6_INT EDMA3CC4 individual completion interrupt 219 EDMACC_4_TC_7_INT EDMA3CC4 individual completion interrupt 220 EDMACC_3_ERRINT EDMA3CC3 error interrupt 221 EDMACC_3_MPINT EDMA3CC3 memory protection interrupt 222 EDMACC_3_TC_0_ERRINT EDMA3CC3 TPTC0 error interrupt 223 EDMACC_3_TC_1_ERRINT EDMA3CC3 TPTC1 error interrupt 224 EDMACC_3_GINT EDMA3CC3 GINT 225 EDMACC_3_TC_0_INT EDMA3CC3 individual completion interrupt 226 EDMACC_3_TC_1_INT EDMA3CC3 individual completion interrupt 227 EDMACC_3_TC_2_INT EDMA3CC3 individual completion interrupt 228 EDMACC_3_TC_3_INT EDMA3CC3 individual completion interrupt 229 EDMACC_3_TC_4_INT EDMA3CC3 individual completion interrupt 230 EDMACC_3_TC_5_INT EDMA3CC3 individual completion interrupt 231 EDMACC_3_TC_6_INT EDMA3CC3 individual completion interrupt 232 EDMACC_3_TC_7_INT EDMA3CC3 individual completion interrupt 233 UART_1_UARTINT UART1 interrupt 234 UART_1_URXEVT UART1 receive event 235 UART_1_UTXEVT UART1 transmit event 236 I2C_1_INT I2C1 interrupt 237 I2C_1_REVT I2C1 receive event 238 I2C_1_XEVT I2C1 transmit event 239 SPI_1_INT0 SPI1 interrupt0 240 SPI_1_INT1 SPI1 interrupt1 241 SPI_1_XEVT SPI1 transmit event 242 SPI_1_REVT SPI1 receive event 243 MPU_5_INT MPU5 addressing violation interrupt and protection violation interrupt 244 MPU_8_INT MPU8 addressing violation interrupt and protection violation interrupt 245 MPU_9_INT MPU9 addressing violation interrupt and protection violation interrupt 246 MPU_11_INT MPU11 addressing violation interrupt and protection violation interrupt 247 MPU_4_INT MPU4 addressing violation interrupt and protection violation interrupt 248 MPU_6_INT MPU6 addressing violation interrupt and protection violation interrupt 249 MPU_7_INT MPU7 addressing violation interrupt and protection violation interrupt 250 MPU_10_INT MPU10 addressing violation interrupt and protection violation interrupt 251 SPI_2_INT0 SPI2 interrupt0 252 SPI_2_INT1 SPI2 interrupt1 253 SPI_2_XEVT SPI2 transmit event 254 SPI_2_REVT SPI2 receive event 124 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 255 I2C_2_INT I2C2 interrupt 256 I2C_2_REVT I2C2 receive event 257 I2C_2_XEVT I2C2 transmit event 258 10GbE_LINK_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 259 10GbE_LINK_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 260 10GbE_USER_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 261 10GbE_USER_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 262 10GbE_MISC_INT 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 263 10GbE_INT_PKTDMA_0 10 Gigabit Ethernet Packet DMA starvation interrupt (66AK2H14 only) 264 Reserved Reserved 265 Reserved Reserved 266 Reserved Reserved 267 Reserved Reserved 268 Reserved Reserved 269 Reserved Reserved 270 Reserved Reserved 271 Reserved Reserved 272 Reserved Reserved 273 Reserved Reserved 274 Reserved Reserved 275 Reserved Reserved 276 Reserved Reserved 277 Reserved Reserved 278 Reserved Reserved 279 Reserved Reserved 280 Reserved Reserved 281 Reserved Reserved 282 Reserved Reserved 283 Reserved Reserved 284 Reserved Reserved 285 Reserved Reserved 286 Reserved Reserved 287 Reserved Reserved 288 Reserved Reserved 289 Reserved Reserved 290 Reserved Reserved 291 Reserved Reserved 292 QMSS_QUE_PEND_652 Navigator transmit queue pending event for indicated queue 293 QMSS_QUE_PEND_653 Navigator transmit queue pending event for indicated queue 294 QMSS_QUE_PEND_654 Navigator transmit queue pending event for indicated queue 295 QMSS_QUE_PEND_655 Navigator transmit queue pending event for indicated queue 296 QMSS_QUE_PEND_656 Navigator transmit queue pending event for indicated queue 297 QMSS_QUE_PEND_657 Navigator transmit queue pending event for indicated queue 298 QMSS_QUE_PEND_8844 Navigator transmit queue pending event for indicated queue 299 QMSS_QUE_PEND_8845 Navigator transmit queue pending event for indicated queue 300 QMSS_QUE_PEND_8846 Navigator transmit queue pending event for indicated queue 301 QMSS_QUE_PEND_8847 Navigator transmit queue pending event for indicated queue Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 125 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 302 QMSS_QUE_PEND_8848 Navigator transmit queue pending event for indicated queue 303 QMSS_QUE_PEND_8849 Navigator transmit queue pending event for indicated queue 304 QMSS_QUE_PEND_8850 Navigator transmit queue pending event for indicated queue 305 QMSS_QUE_PEND_8851 Navigator transmit queue pending event for indicated queue 306 QMSS_QUE_PEND_8852 Navigator transmit queue pending event for indicated queue 307 QMSS_QUE_PEND_8853 Navigator transmit queue pending event for indicated queue 308 QMSS_QUE_PEND_8854 Navigator transmit queue pending event for indicated queue 309 QMSS_QUE_PEND_8855 Navigator transmit queue pending event for indicated queue 310 QMSS_QUE_PEND_8856 Navigator transmit queue pending event for indicated queue 311 QMSS_QUE_PEND_8857 Navigator transmit queue pending event for indicated queue 312 QMSS_QUE_PEND_8858 Navigator transmit queue pending event for indicated queue 313 QMSS_QUE_PEND_8859 Navigator transmit queue pending event for indicated queue 314 QMSS_QUE_PEND_8860 Navigator transmit queue pending event for indicated queue 315 QMSS_QUE_PEND_8861 Navigator transmit queue pending event for indicated queue 316 QMSS_QUE_PEND_8862 Navigator transmit queue pending event for indicated queue 317 QMSS_QUE_PEND_8863 Navigator transmit queue pending event for indicated queue 318 QMSS_INTD_2_PKTDMA_0 Navigator ECC error interrupt 319 QMSS_INTD_2_PKTDMA_1 Navigator ECC error interrupt 320 QMSS_INTD_1_LOW_0 Navigator interrupt low 321 QMSS_INTD_1_LOW_1 Navigator interrupt low 322 QMSS_INTD_1_LOW_2 Navigator interrupt low 323 QMSS_INTD_1_LOW_3 Navigator interrupt low 324 QMSS_INTD_1_LOW_4 Navigator interrupt low 325 QMSS_INTD_1_LOW_5 Navigator interrupt low 326 QMSS_INTD_1_LOW_6 Navigator interrupt low 327 QMSS_INTD_1_LOW_7 Navigator interrupt low 328 QMSS_INTD_1_LOW_8 Navigator interrupt low 329 QMSS_INTD_1_LOW_9 Navigator interrupt low 330 QMSS_INTD_1_LOW_10 Navigator interrupt low 331 QMSS_INTD_1_LOW_11 Navigator interrupt low 332 QMSS_INTD_1_LOW_12 Navigator interrupt low 333 QMSS_INTD_1_LOW_13 Navigator interrupt low 334 QMSS_INTD_1_LOW_14 Navigator interrupt low 335 QMSS_INTD_1_LOW_15 Navigator interrupt low 336 QMSS_INTD_2_LOW_0 Navigator second interrupt low 337 QMSS_INTD_2_LOW_1 Navigator second interrupt low 338 QMSS_INTD_2_LOW_2 Navigator second interrupt low 339 QMSS_INTD_2_LOW_3 Navigator second interrupt low 340 QMSS_INTD_2_LOW_4 Navigator second interrupt low 341 QMSS_INTD_2_LOW_5 Navigator second interrupt low 342 QMSS_INTD_2_LOW_6 Navigator second interrupt low 343 QMSS_INTD_2_LOW_7 Navigator second interrupt low 344 QMSS_INTD_2_LOW_8 Navigator second interrupt low 345 QMSS_INTD_2_LOW_9 Navigator second interrupt low 346 QMSS_INTD_2_LOW_10 Navigator second interrupt low 347 QMSS_INTD_2_LOW_11 Navigator second interrupt low 348 QMSS_INTD_2_LOW_12 Navigator second interrupt low 126 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 349 QMSS_INTD_2_LOW_13 Navigator second interrupt low 350 QMSS_INTD_2_LOW_14 Navigator second interrupt low 351 QMSS_INTD_2_LOW_15 Navigator second interrupt low 352 TRACER_EDMACC_0 Tracer sliding time window interrupt for EDMA3CC0 353 TRACER_EDMACC_123_INT Tracer sliding time window interrupt for EDMA3CC1, EDMA3CC2 and EDMA3CC3 354 TRACER_CIC_INT Tracer sliding time window interrupt for interrupt controllers (CIC) 355 TRACER_MSMC_4_INT Tracer sliding time window interrupt for MSMC SRAM bank4 356 TRACER_MSMC_5_INT Tracer sliding time window interrupt for MSMC SRAM bank5 357 TRACER_MSMC_6_INT Tracer sliding time window interrupt for MSMC SRAM bank6 358 TRACER_MSMC_7_INT Tracer sliding time window interrupt for MSMC SRAM bank7 359 TRACER_SPI_ROM_EMIF_INT Tracer sliding time window interrupt for SPI/ROM/EMIF16 modules 360 TRACER_QMSS_QM_CFG2_INT Tracer sliding time window interrupt for QM2 361 Reserved Reserved 362 Reserved Reserved 363 TRACER_DDR_1_INT Tracer sliding time window interrupt for DDR3B 364 Reserved Reserved 365 HYPERLINK_1_INT HyperLink 1 interrupt 366 Reserved Reserved 367 Reserved Reserved 368 Reserved Reserved 369 Reserved Reserved 370 Reserved Reserved 371 Reserved Reserved 372 Reserved Reserved 373 Reserved Reserved 374 Reserved Reserved 375 Reserved Reserved 376 Reserved Reserved 377 Reserved Reserved 378 Reserved Reserved 379 Reserved Reserved 380 Reserved Reserved 381 Reserved Reserved 382 Reserved Reserved 383 Reserved Reserved 384 Reserved Reserved 385 Reserved Reserved 386 Reserved Reserved 387 Reserved Reserved 388 Reserved Reserved 389 Reserved Reserved 390 Reserved Reserved 391 Reserved Reserved 392 Reserved Reserved 393 Reserved Reserved 394 Reserved Reserved 395 Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 127 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 396 Reserved Reserved 397 Reserved Reserved 398 Reserved Reserved 399 Reserved Reserved 400 Reserved Reserved 401 Reserved Reserved 402 Reserved Reserved 403 Reserved Reserved 404 Reserved Reserved 405 Reserved Reserved 406 Reserved Reserved 407 Reserved Reserved 408 Reserved Reserved 409 Reserved Reserved 410 Reserved Reserved 411 Reserved Reserved 412 Reserved Reserved 413 Reserved Reserved 414 Reserved Reserved 415 Reserved Reserved 416 Reserved Reserved 417 Reserved Reserved 418 Reserved Reserved 419 Reserved Reserved 420 Reserved Reserved 421 Reserved Reserved 422 USB_INT00 USB interrupt 423 USB_INT04 USB interrupt 424 USB_INT05 USB interrupt 425 USB_INT06 USB interrupt 426 USB_INT07 USB interrupt 427 USB_INT08 USB interrupt 428 USB_INT09 USB interrupt 429 USB_INT10 USB interrupt 430 USB_INT11 USB interrupt 431 USB_MISCINT USB miscellaneous interrupt 432 USB_OABSINT USB OABS interrupt 433 TIMER_12_INTL Timer interrupt low 434 TIMER_12_INTH Timer interrupt high 435 TIMER_13_INTL Timer interrupt low 436 TIMER_13_INTH Timer interrupt high 437 TIMER_14_INTL Timer interrupt low 438 TIMER_14_INTH Timer interrupt high 439 TIMER_15_INTL Timer interrupt low 440 TIMER_15_INTH Timer interrupt high 441 TIMER_16_INTL Timer interrupt low 442 TIMER_17_INTL Timer interrupt high 128 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-25. CIC1 Event Inputs — C66x CorePac Secondary Interrupts (continued) EVENT NO. EVENT NAME DESCRIPTION 443 TIMER_18_INTL Timer interrupt low (1) 444 TIMER_19_INTL Timer interrupt high (1) 445 DDR3_1_ERR DDR3B_EMIF error interrupt 446 GPIO_INT16 GPIO interrupt 447 GPIO_INT17 GPIO interrupt 448 GPIO_INT18 GPIO interrupt 449 GPIO_INT19 GPIO interrupt 450 GPIO_INT20 GPIO interrupt 451 GPIO_INT21 GPIO interrupt 452 GPIO_INT22 GPIO interrupt 453 GPIO_INT23 GPIO interrupt 454 GPIO_INT24 GPIO interrupt 455 GPIO_INT25 GPIO interrupt 456 GPIO_INT26 GPIO interrupt 457 GPIO_INT27 GPIO interrupt 458 GPIO_INT28 GPIO interrupt 459 GPIO_INT29 GPIO interrupt 460 GPIO_INT30 GPIO interrupt 461 GPIO_INT31 GPIO interrupt 462 SRIO_INTDST20 SRIOI interrupt 463 SRIO_INTDST21 SRIOI interrupt 464 SRIO_INTDST22 SRIOI interrupt 465 SRIO_INTDST23 SRIOI interrupt 466 PCIE_INT8 PCIE MSI interrupt 467 PCIE_INT9 PCIE MSI interrupt 468 PCIE_INT10 PCIE MSI interrupt 469 PCIE_INT11 PCIE MSI interrupt 470 SEM_INT12 Semaphore interrupt 471 SEM_INT13 Semaphore interrupt 472 SEM_ERR12 Semaphore error interrupt 473 SEM_ERR13 Semaphore error interrupt 474 Reserved Reserved Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) EVENT NO. EVENT NAME DESCRIPTION 0 GPIO_INT8 GPIO interrupt 1 GPIO_INT9 GPIO interrupt 2 GPIO_INT10 GPIO interrupt 3 GPIO_INT11 GPIO interrupt 4 GPIO_INT12 GPIO interrupt 5 GPIO_INT13 GPIO interrupt 6 GPIO_INT14 GPIO interrupt 7 GPIO_INT15 GPIO interrupt 8 DBGTBR_DMAINT Debug trace buffer (TBR) DMA event 9 Reserved Reserved 10 Reserved Reserved 11 TETB_FULLINT0 TETB0 is full Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 129 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 12 TETB_HFULLINT0 TETB0 is half full 13 TETB_ACQINT0 TETB0 acquisition has been completed 14 TETB_FULLINT1 TETB1 is full 15 TETB_HFULLINT1 TETB1 is half full 16 TETB_ACQINT1 TETB1 acquisition has been completed 17 TETB_FULLINT2 TETB2 is full 18 TETB_HFULLINT2 TETB2 is half full 19 TETB_ACQINT2 TETB2 acquisition has been completed 20 TETB_FULLINT3 TETB3 is full 21 TETB_HFULLINT3 TETB3 is half full 22 TETB_ACQINT3 TETB3 acquisition has been completed 23 Reserved Reserved 24 QMSS_INTD_1_HIGH_16 Navigator hi interrupt 25 QMSS_INTD_1_HIGH_17 Navigator hi interrupt 26 QMSS_INTD_1_HIGH_18 Navigator hi interrupt 27 QMSS_INTD_1_HIGH_19 Navigator hi interrupt 28 QMSS_INTD_1_HIGH_20 Navigator hi interrupt 29 QMSS_INTD_1_HIGH_21 Navigator hi interrupt 30 QMSS_INTD_1_HIGH_22 Navigator hi interrupt 31 QMSS_INTD_1_HIGH_23 Navigator hi interrupt 32 QMSS_INTD_1_HIGH_24 Navigator hi interrupt 33 QMSS_INTD_1_HIGH_25 Navigator hi interrupt 34 QMSS_INTD_1_HIGH_26 Navigator hi interrupt 35 QMSS_INTD_1_HIGH_27 Navigator hi interrupt 36 QMSS_INTD_1_HIGH_28 Navigator hi interrupt 37 QMSS_INTD_1_HIGH_29 Navigator hi interrupt 38 QMSS_INTD_1_HIGH_30 Navigator hi interrupt 39 QMSS_INTD_1_HIGH_31 Navigator hi interrupt 40 NETCP_MDIO_LINK_INT0 Packet Accelerator 0 subsystem MDIO interrupt 41 NETCP_MDIO_LINK_INT1 Packet Accelerator 0 subsystem MDIO interrupt 42 NETCP_MDIO_USER_INT0 Packet Accelerator 0 subsystem MDIO interrupt 43 NETCP_MDIO_USER_INT1 Packet Accelerator 0 subsystem MDIO interrupt 44 NETCP_MISC_INT Packet Accelerator 0 subsystem MDIO interrupt 45 TRACER_CORE_0_INT Tracer sliding time window interrupt for DSP0 L2 46 TRACER_CORE_1_INT Tracer sliding time window interrupt for DSP1 L2 47 TRACER_CORE_2_INT Tracer sliding time window interrupt for DSP2 L2 48 TRACER_CORE_3_INT Tracer sliding time window interrupt for DSP3 L2 49 TRACER_DDR_INT Tracer sliding time window interrupt for MSMC-DDR3A 50 TRACER_MSMC_0_INT Tracer sliding time window interrupt for MSMC SRAM bank0 51 TRACER_MSMC_1_INT Tracer sliding time window interrupt for MSMC SRAM bank1 52 TRACER_MSMC_2_INT Tracer sliding time window interrupt for MSMC SRAM bank2 53 TRACER_MSMC_3_INT Tracer sliding time window interrupt for MSMC SRAM bank3 54 TRACER_CFG_INT Tracer sliding time window interrupt for TeraNet CFG 55 TRACER_QMSS_QM_CFG1_INT Tracer sliding time window interrupt for Navigator CFG1 slave port 56 TRACER_QMSS_DMA_INT Tracer sliding time window interrupt for Navigator DMA internal bus slave port 57 TRACER_SEM_INT Tracer sliding time window interrupt for Semaphore interrupt 58 SEM_ERR0 Semaphore error interrupt 130 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 59 SEM_ERR1 Semaphore error interrupt 60 SEM_ERR2 Semaphore error interrupt 61 SEM_ERR3 Semaphore error interrupt 62 BOOTCFG_INT BOOTCFG error interrupt 63 NETCP_PKTDMA_INT0 Packet Accelerator0 Packet DMA starvation interrupt 64 MPU_0_INT MPU0 interrupt 65 MSMC_SCRUB_CERROR MSMC error interrupt 66 MPU_1_INT MPU1 interrupt 67 SRIO_INT_PKTDMA_0 Packet Accelerator0 Packet DMA interrupt 68 MPU_2_INT MPU2 interrupt 69 QMSS_INTD_1_PKTDMA_0 Navigator Packet DMA interrupt 70 MPU_3_INT MPU3 interrupt 71 QMSS_INTD_1_PKTDMA_1 Navigator Packet DMA interrupt 72 MSMC_DEDC_CERROR MSMC error interrupt 73 MSMC_DEDC_NC_ERROR MSMC error interrupt 74 MSMC_SCRUB_NC_ERROR MSMC error interrupt 75 Reserved Reserved 76 MSMC_MPF_ERROR0 Memory protection fault indicators for system master PrivID = 0 77 MSMC_MPF_ERROR1 Memory protection fault indicators for system master PrivID = 1 78 MSMC_MPF_ERROR2 Memory protection fault indicators for system master PrivID = 2 79 MSMC_MPF_ERROR3 Memory protection fault indicators for system master PrivID = 3 80 MSMC_MPF_ERROR4 Memory protection fault indicators for system master PrivID = 4 81 MSMC_MPF_ERROR5 Memory protection fault indicators for system master PrivID = 5 82 MSMC_MPF_ERROR6 Memory protection fault indicators for system master PrivID = 6 83 MSMC_MPF_ERROR7 Memory protection fault indicators for system master PrivID = 7 84 MSMC_MPF_ERROR8 Memory protection fault indicators for system master PrivID = 8 85 MSMC_MPF_ERROR9 Memory protection fault indicators for system master PrivID = 9 86 MSMC_MPF_ERROR10 Memory protection fault indicators for system master PrivID = 10 87 MSMC_MPF_ERROR11 Memory protection fault indicators for system master PrivID = 11 88 MSMC_MPF_ERROR12 Memory protection fault indicators for system master PrivID = 12 89 MSMC_MPF_ERROR13 Memory protection fault indicators for system master PrivID = 13 90 MSMC_MPF_ERROR14 Memory protection fault indicators for system master PrivID = 14 91 MSMC_MPF_ERROR15 Memory protection fault indicators for system master PrivID = 15 92 Reserved Reserved 93 SRIO_INTDST0 SRIO interrupt 94 SRIO_INTDST1 SRIO interrupt 95 SRIO_INTDST2 SRIO interrupt 96 SRIO_INTDST3 SRIO interrupt 97 SRIO_INTDST4 SRIO interrupt 98 SRIO_INTDST5 SRIO interrupt 99 SRIO_INTDST6 SRIO interrupt 100 SRIO_INTDST7 SRIO interrupt 101 SRIO_INTDST8 SRIO interrupt 102 SRIO_INTDST9 SRIO interrupt 103 SRIO_INTDST10 SRIO interrupt 104 SRIO_INTDST11 SRIO interrupt 105 SRIO_INTDST12 SRIO interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 131 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 106 SRIO_INTDST13 SRIO interrupt 107 SRIO_INTDST14 SRIO interrupt 108 SRIO_INTDST15 SRIO interrupt 109 SRIO_INTDST16 SRIO interrupt 110 SRIO_INTDST17 SRIO interrupt 111 SRIO_INTDST18 SRIO interrupt 112 SRIO_INTDST19 SRIO interrupt 113 SRIO_INTDST20 SRIO interrupt 114 SRIO_INTDST21 SRIO interrupt 115 SRIO_INTDST22 SRIO interrupt 116 SRIO_INTDST23 SRIO interrupt 117 AEMIF_EASYNCERR Asynchronous EMIF16 error interrupt 118 TETB_FULLINT4 TETB4 is full 119 TETB_HFULLINT4 TETB4 is half full 120 TETB_ACQINT4 TETB4 acquisition has been completed 121 TETB_FULLINT5 TETB5 is full 122 TETB_HFULLINT5 TETB5 is half full 123 TETB_ACQINT5 TETB5 acquisition has been completed 124 TETB_FULLINT6 TETB6 is full 125 TETB_HFULLINT6 TETB6 is half full 126 TETB_ACQINT6 TETB6 acquisition has been completed 127 TETB_FULLINT7 TETB7 is full 128 TETB_HFULLINT7 TETB7 is half full 129 TETB_ACQINT7 TETB7 acquisition has been completed 130 TRACER_CORE_4_INT Tracer sliding time window interrupt for DSP4 L2 131 TRACER_CORE_5_INT Tracer sliding time window interrupt for DSP5 L2 132 TRACER_CORE_6_INT Tracer sliding time window interrupt for DSP6 L2 133 TRACER_CORE_7_INT Tracer sliding time window interrupt for DSP7 L2 134 SEM_ERR4 Semaphore error interrupt 135 SEM_ERR5 Semaphore error interrupt 136 SEM_ERR6 Semaphore error interrupt 137 SEM_ERR7 Semaphore error interrupt 138 QMSS_INTD_1_HIGH_0 Navigator hi interrupt 139 QMSS_INTD_1_HIGH_1 Navigator hi interrupt 140 QMSS_INTD_1_HIGH_2 Navigator hi interrupt 141 QMSS_INTD_1_HIGH_3 Navigator hi interrupt 142 QMSS_INTD_1_HIGH_4 Navigator hi interrupt 143 QMSS_INTD_1_HIGH_5 Navigator hi interrupt 144 QMSS_INTD_1_HIGH_6 Navigator hi interrupt 145 QMSS_INTD_1_HIGH_7 Navigator hi interrupt 146 QMSS_INTD_1_HIGH_8 Navigator hi interrupt 147 QMSS_INTD_1_HIGH_9 Navigator hi interrupt 148 QMSS_INTD_1_HIGH_10 Navigator hi interrupt 149 QMSS_INTD_1_HIGH_11 Navigator hi interrupt 150 QMSS_INTD_1_HIGH_12 Navigator hi interrupt 151 QMSS_INTD_1_HIGH_13 Navigator hi interrupt 152 QMSS_INTD_1_HIGH_14 Navigator hi interrupt 132 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 153 QMSS_INTD_1_HIGH_15 Navigator hi interrupt 154 QMSS_INTD_2_HIGH_0 Navigator second hi interrupt 155 QMSS_INTD_2_HIGH_1 Navigator second hi interrupt 156 QMSS_INTD_2_HIGH_2 Navigator second hi interrupt 157 QMSS_INTD_2_HIGH_3 Navigator second hi interrupt 158 QMSS_INTD_2_HIGH_4 Navigator second hi interrupt 159 QMSS_INTD_2_HIGH_5 Navigator second hi interrupt 160 QMSS_INTD_2_HIGH_6 Navigator second hi interrupt 161 QMSS_INTD_2_HIGH_7 Navigator second hi interrupt 162 QMSS_INTD_2_HIGH_8 Navigator second hi interrupt 163 QMSS_INTD_2_HIGH_9 Navigator second hi interrupt 164 QMSS_INTD_2_HIGH_10 Navigator second hi interrupt 165 QMSS_INTD_2_HIGH_11 Navigator second hi interrupt 166 QMSS_INTD_2_HIGH_12 Navigator second hi interrupt 167 QMSS_INTD_2_HIGH_13 Navigator second hi interrupt 168 QMSS_INTD_2_HIGH_14 Navigator second hi interrupt 169 QMSS_INTD_2_HIGH_15 Navigator second hi interrupt 170 QMSS_INTD_2_HIGH_16 Navigator second hi interrupt 171 QMSS_INTD_2_HIGH_17 Navigator second hi interrupt 172 QMSS_INTD_2_HIGH_18 Navigator second hi interrupt 173 QMSS_INTD_2_HIGH_19 Navigator second hi interrupt 174 QMSS_INTD_2_HIGH_20 Navigator second hi interrupt 175 QMSS_INTD_2_HIGH_21 Navigator second hi interrupt 176 QMSS_INTD_2_HIGH_22 Navigator second hi interrupt 177 QMSS_INTD_2_HIGH_23 Navigator second hi interrupt 178 QMSS_INTD_2_HIGH_24 Navigator second hi interrupt 179 QMSS_INTD_2_HIGH_25 Navigator second hi interrupt 180 QMSS_INTD_2_HIGH_26 Navigator second hi interrupt 181 QMSS_INTD_2_HIGH_27 Navigator second hi interrupt 182 QMSS_INTD_2_HIGH_28 Navigator second hi interrupt 183 QMSS_INTD_2_HIGH_29 Navigator second hi interrupt 184 QMSS_INTD_2_HIGH_30 Navigator second hi interrupt 185 QMSS_INTD_2_HIGH_31 Navigator second hi interrupt 186 MPU_12_INT MPU12 addressing violation interrupt and protection violation interrupt 187 MPU_13_INT MPU13 addressing violation interrupt and protection violation interrupt 188 MPU_14_INT MPU14 addressing violation interrupt and protection violation interrupt 189 Reserved Reserved 190 Reserved Reserved 191 Reserved Reserved 192 Reserved Reserved 193 Reserved Reserved 194 Reserved Reserved 195 Reserved Reserved 196 Reserved Reserved 197 Reserved Reserved 198 Reserved Reserved 199 TRACER_QMSS_QM_CFG2_INT Tracer sliding time window interrupt for Navigator CFG2 slave port Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 133 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 200 TRACER_EDMACC_0 Tracer sliding time window interrupt foR EDMA3CC0 201 TRACER_EDMACC_123_INT Tracer sliding time window interrupt for EDMA3CC1, EDMA3CC2 and EDMA3CC3 202 TRACER_CIC_INT Tracer sliding time window interrupt for interrupt controllers (CIC) 203 Reserved Reserved 204 MPU_5_INT MPU5 addressing violation interrupt and protection violation interrupt 205 Reserved Reserved 206 MPU_7_INT MPU7 addressing violation interrupt and protection violation interrupt 207 MPU_8_INT MPU8 addressing violation interrupt and protection violation interrupt 208 QMSS_INTD_2_PKTDMA_0 Navigator ECC error interrupt 209 QMSS_INTD_2_PKTDMA_1 Navigator ECC error interrupt 210 SR_0_VPSMPSACK SmartReflex VPVOLTUPDATE asserted and SMPS has acknowledged in a defined time interval 211 DDR3_0_ERR DDR3A error interrupt 212 HYPERLINK_0_INT HyperLink 0 interrupt 213 EDMACC_0_ERRINT EDMA3CC0 error interrupt 214 EDMACC_0_MPINT EDMA3CC0 memory protection interrupt 215 EDMACC_0_TC_0_ERRINT EDMA3CC0 TPTC0 error interrupt 216 EDMACC_0_TC_1_ERRINT EDMA3CC0 TPTC1 error interrupt 217 EDMACC_1_ERRINT EDMA3CC1 error interrupt 218 EDMACC_1_MPINT EDMA3CC1 memory protection interrupt 219 EDMACC_1_TC_0_ERRINT EDMA3CC1 TPTC0 error interrupt 220 EDMACC_1_TC_1_ERRINT EDMA3CC1 TPTC1 error interrupt 221 EDMACC_1_TC_2_ERRINT EDMA3CC1 TPTC2 error interrupt 222 EDMACC_1_TC_3_ERRINT EDMA3CC1 TPTC3 error interrupt 223 EDMACC_2_ERRINT EDMA3CC2 error interrupt 224 EDMACC_2_MPINT EDMA3CC2 memory protection interrupt 225 EDMACC_2_TC_0_ERRINT EDMA3CC2 TPTC0 error interrupt 226 EDMACC_2_TC_1_ERRINT EDMA3CC2 TPTC1 error interrupt 227 EDMACC_2_TC_2_ERRINT EDMA3CC2 TPTC2 error interrupt 228 EDMACC_2_TC_3_ERRINT EDMA3CC2 TPTC3 error interrupt 229 EDMACC_3_ERRINT EDMA3CC3 error interrupt 230 EDMACC_3_MPINT EDMA3CC3 memory protection interrupt 231 EDMACC_3_TC_0_ERRINT EDMA3CC3 TPTC0 error interrupt 232 EDMACC_3_TC_1_ERRINT EDMA3CC3 TPTC1 error interrupt 233 EDMACC_4_ERRINT EDMA3CC4 error interrupt 234 EDMACC_4_MPINT EDMA3CC4 memory protection interrupt 235 EDMACC_4_TC_0_ERRINT EDMA3CC4 TPTC0 error interrupt 236 EDMACC_4_TC_1_ERRINT EDMA3CC4 TPTC1 error interrupt 237 QMSS_QUE_PEND_652 Navigator transmit queue pending event for indicated queue 238 QMSS_QUE_PEND_653 Navigator transmit queue pending event for indicated queue 239 QMSS_QUE_PEND_654 Navigator transmit queue pending event for indicated queue 240 QMSS_QUE_PEND_655 Navigator transmit queue pending event for indicated queue 241 QMSS_QUE_PEND_656 Navigator transmit queue pending event for indicated queue 242 QMSS_QUE_PEND_657 Navigator transmit queue pending event for indicated queue 243 QMSS_QUE_PEND_658 Navigator transmit queue pending event for indicated queue 244 QMSS_QUE_PEND_659 Navigator transmit queue pending event for indicated queue 245 QMSS_QUE_PEND_660 Navigator transmit queue pending event for indicated queue 134 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 246 QMSS_QUE_PEND_661 Navigator transmit queue pending event for indicated queue 247 QMSS_QUE_PEND_662 Navigator transmit queue pending event for indicated queue 248 QMSS_QUE_PEND_663 Navigator transmit queue pending event for indicated queue 249 QMSS_QUE_PEND_664 Navigator transmit queue pending event for indicated queue 250 QMSS_QUE_PEND_665 Navigator transmit queue pending event for indicated queue 251 QMSS_QUE_PEND_666 Navigator transmit queue pending event for indicated queue 252 QMSS_QUE_PEND_667 Navigator transmit queue pending event for indicated queue 253 QMSS_QUE_PEND_668 Navigator transmit queue pending event for indicated queue 254 QMSS_QUE_PEND_669 Navigator transmit queue pending event for indicated queue 255 QMSS_QUE_PEND_670 Navigator transmit queue pending event for indicated queue 256 QMSS_QUE_PEND_671 Navigator transmit queue pending event for indicated queue 257 QMSS_QUE_PEND_8844 Navigator transmit queue pending event for indicated queue 258 QMSS_QUE_PEND_8845 Navigator transmit queue pending event for indicated queue 259 QMSS_QUE_PEND_8846 Navigator transmit queue pending event for indicated queue 260 QMSS_QUE_PEND_8847 Navigator transmit queue pending event for indicated queue 261 QMSS_QUE_PEND_8848 Navigator transmit queue pending event for indicated queue 262 QMSS_QUE_PEND_8849 Navigator transmit queue pending event for indicated queue 263 QMSS_QUE_PEND_8850 Navigator transmit queue pending event for indicated queue 264 QMSS_QUE_PEND_8851 Navigator transmit queue pending event for indicated queue 265 QMSS_QUE_PEND_8852 Navigator transmit queue pending event for indicated queue 266 QMSS_QUE_PEND_8853 Navigator transmit queue pending event for indicated queue 267 QMSS_QUE_PEND_8854 Navigator transmit queue pending event for indicated queue 268 QMSS_QUE_PEND_8855 Navigator transmit queue pending event for indicated queue 269 QMSS_QUE_PEND_8856 Navigator transmit queue pending event for indicated queue 270 QMSS_QUE_PEND_8857 Navigator transmit queue pending event for indicated queue 271 QMSS_QUE_PEND_8858 Navigator transmit queue pending event for indicated queue 272 QMSS_QUE_PEND_8859 Navigator transmit queue pending event for indicated queue 273 QMSS_QUE_PEND_8860 Navigator transmit queue pending event for indicated queue 274 QMSS_QUE_PEND_8861 Navigator transmit queue pending event for indicated queue 275 QMSS_QUE_PEND_8862 Navigator transmit queue pending event for indicated queue 276 QMSS_QUE_PEND_8863 Navigator transmit queue pending event for indicated queue 277 10GbE_LINK_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 278 10GbE_LINK_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 279 10GbE_USER_INT0 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 280 10GbE_USER_INT1 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 281 10GbE_MISC_INT 10 Gigabit Ethernet subsystem MDIO interrupt (66AK2H14 only) 282 10GbE_INT_PKTDMA_0 10 Gigabit Ethernet Packet DMA starvation interrupt 283 SEM_INT0 Semaphore interrupt 284 SEM_INT1 Semaphore interrupt 285 SEM_INT2 Semaphore interrupt 286 SEM_INT3 Semaphore interrupt 287 SEM_INT4 Semaphore interrupt 288 SEM_INT5 Semaphore interrupt 289 SEM_INT6 Semaphore interrupt 290 SEM_INT7 Semaphore interrupt 291 SEM_INT8 Semaphore interrupt 292 SEM_INT9 Semaphore interrupt Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 135 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 293 SEM_INT10 Semaphore interrupt 294 SEM_INT11 Semaphore interrupt 295 SEM_INT12 Semaphore interrupt 296 SEM_INT13 Semaphore interrupt 297 SEM_INT14 Semaphore interrupt 298 SEM_INT15 Semaphore interrupt 299 SEM_ERR8 Semaphore error interrupt 300 SEM_ERR9 Semaphore error interrupt 301 SEM_ERR10 Semaphore error interrupt 302 SEM_ERR11 Semaphore error interrupt 303 SEM_ERR12 Semaphore error interrupt 304 SEM_ERR13 Semaphore error interrupt 305 SEM_ERR14 Semaphore error interrupt 306 SEM_ERR15 Semaphore error interrupt 307 DDR3_1_ERR DDR3B error interrupt 308 HYPERLINK_1_INT HyperLink 1 interrupt 309 Reserved Reserved 310 Reserved Reserved 311 Reserved Reserved 312 Reserved Reserved 313 Reserved Reserved 314 Reserved Reserved 315 Reserved Reserved 316 Reserved Reserved 317 Reserved Reserved 318 Reserved Reserved 319 Reserved Reserved 320 Reserved Reserved 321 Reserved Reserved 322 Reserved Reserved 323 Reserved Reserved 324 Reserved Reserved 325 Reserved Reserved 326 Reserved Reserved 327 Reserved Reserved 328 Reserved Reserved 329 Reserved Reserved 330 Reserved Reserved 331 Reserved Reserved 332 Reserved Reserved 333 Reserved Reserved 334 Reserved Reserved 335 Reserved Reserved 336 Reserved Reserved 337 Reserved Reserved 338 Reserved Reserved 339 Reserved Reserved 136 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 340 Reserved Reserved 341 Reserved Reserved 342 Reserved Reserved 343 Reserved Reserved 344 Reserved Reserved 345 Reserved Reserved 346 Reserved Reserved 347 Reserved Reserved 348 Reserved Reserved 349 Reserved Reserved 350 Reserved Reserved 351 Reserved Reserved 352 Reserved Reserved 353 Reserved Reserved 354 Reserved Reserved 355 Reserved Reserved 356 Reserved Reserved 357 Reserved Reserved 358 Reserved Reserved 359 Reserved Reserved 360 Reserved Reserved 361 Reserved Reserved 362 PSC_ALLINT PSC interrupt 363 Reserved Reserved 364 Reserved Reserved 365 Reserved Reserved 366 Reserved Reserved 367 Reserved Reserved 368 Reserved Reserved 369 Reserved Reserved 370 Reserved Reserved 371 Reserved Reserved 372 MPU_9_INT MPU9 addressing violation interrupt and protection violation interrupt 373 MPU_10_INT MPU10 addressing violation interrupt and protection violation interrupt 374 MPU_11_INT MPU11 addressing violation interrupt and protection violation interrupt 375 TRACER_MSMC_4_INT Tracer sliding time window interrupt for MSMC SRAM Bank 4 376 TRACER_MSMC_5_INT Tracer sliding time window interrupt for MSMC SRAM Bank 4 377 TRACER_MSMC_6_INT Tracer sliding time window interrupt for MSMC SRAM Bank 4 378 TRACER_MSMC_7_INT Tracer sliding time window interrupt for MSMC SRAM Bank 4 379 TRACER_DDR_1_INT Tracer sliding time window interrupt for DDR3B 380 Reserved Reserved 381 Reserved Reserved 382 Reserved Reserved 383 Reserved Reserved 384 TRACER_SPI_ROM_EMIF_INT Tracer sliding time window interrupt for SPI/ROM/EMIF16 modules 385 Reserved Reserved 386 Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 137 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 387 TIMER_8_INTL Timer interrupt low 388 TIMER_8_INTH Timer interrupt high 389 TIMER_9_INTL Timer interrupt low 390 TIMER_9_INTH Timer interrupt high 391 TIMER_10_INTL Timer interrupt low 392 TIMER_10_INTH Timer interrupt high 393 TIMER_11_INTL Timer interrupt low 394 TIMER_11_INTH Timer interrupt high 395 TIMER_14_INTL Timer interrupt low 396 TIMER_14_INTH Timer interrupt high 397 TIMER_15_INTL Timer interrupt low 398 TIMER_15_INTH Timer interrupt high 399 USB_INT00 USB interrupt 400 USB_INT04 USB interrupt 401 USB_INT05 USB interrupt 402 USB_INT06 USB interrupt 403 USB_INT07 USB interrupt 404 USB_INT08 USB interrupt 405 USB_INT09 USB interrupt 406 USB_INT10 USB interrupt 407 USB_INT11 USB interrupt 408 USB_MISCINT USB miscellaneous interrupt 409 USB_OABSINT USB OABS interrupt 410 Reserved Reserved 411 Reserved Reserved 412 Reserved Reserved 413 Reserved Reserved 414 Reserved Reserved 415 Reserved Reserved 416 Reserved Reserved 417 Reserved Reserved 418 Reserved Reserved 419 Reserved Reserved 420 Reserved Reserved 421 Reserved Reserved 422 Reserved Reserved 423 Reserved Reserved 424 Reserved Reserved 425 Reserved Reserved 426 Reserved Reserved 427 Reserved Reserved 428 Reserved Reserved 429 Reserved Reserved 430 Reserved Reserved 431 Reserved Reserved 432 Reserved Reserved 433 Reserved Reserved 138 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-26. CIC2 Event Inputs (Secondary Events for EDMA3CC0 and Hyperlinks) (continued) EVENT NO. EVENT NAME DESCRIPTION 434 Reserved Reserved 435 Reserved Reserved 436 Reserved Reserved 437 Reserved Reserved 438 Reserved Reserved 439 Reserved Reserved 440 Reserved Reserved 441 Reserved Reserved 442 TETB_OVFLINT0 ETB0 overflow (emulation trace buffer) 443 TETB_UNFLINT0 ETB0 underflow 444 TETB_OVFLINT1 ETB1 overflow (emulation trace buffer) 445 TETB_UNFLINT1 ETB1 underflow 446 TETB_OVFLINT2 ETB2 overflow (emulation trace buffer) 447 TETB_UNFLINT2 ETB2 underflow 448 TETB_OVFLINT3 ETB3 overflow (emulation trace buffer) 449 TETB_UNFLINT3 ETB3 underflow 450 TETB_OVFLINT4 ETB4 overflow (emulation trace buffer) 451 TETB_UNFLINT4 ETB4 underflow 452 TETB_OVFLINT5 ETB5 overflow (emulation trace buffer) 453 TETB_UNFLINT5 ETB5 underflow 454 TETB_OVFLINT6 ETB6 overflow (emulation trace buffer) 455 TETB_UNFLINT6 ETB6 underflow 456 TETB_OVFLINT7 ETB7 overflow (emulation trace buffer) 457 TETB_UNFLINT7 ETB7 underflow 458 ARM_TBR_DMA ARM trace buffer 459 Reserved Reserved 460 Reserved Reserved 461 Reserved Reserved 462 Reserved Reserved 463 GPIO_INT0 GPIO interrupt 464 GPIO_INT1 GPIO interrupt 465 GPIO_INT2 GPIO interrupt 466 GPIO_INT3 GPIO interrupt 467 GPIO_INT4 GPIO interrupt 468 GPIO_INT5 GPIO interrupt 469 GPIO_INT6 GPIO interrupt 470 GPIO_INT7 GPIO interrupt 471 IPC_GR0 IPC interrupt generation 472 IPC_GR1 IPC interrupt generation 473 IPC_GR2 IPC interrupt generation 474 IPC_GR3 IPC interrupt generation 475 IPC_GR4 IPC interrupt generation 476 IPC_GR5 IPC interrupt generation 477 IPC_GR6 IPC interrupt generation 478 IPC_GR7 IPC interrupt generation Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 139 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 8.3.2 www.ti.com CIC Registers This section includes the CIC memory map information and registers. 8.3.2.1 CIC0 Register Map Table 8-27. CIC0 Registers ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x0 REVISION_REG Revision Register 0x4 CONTROL_REG Control Register 0xC HOST_CONTROL_REG Host Control Register 0x10 GLOBAL_ENABLE_HINT_REG Global Host Int Enable Register 0x20 STATUS_SET_INDEX_REG Status Set Index Register 0x24 STATUS_CLR_INDEX_REG Status Clear Index Register 0x28 ENABLE_SET_INDEX_REG Enable Set Index Register 0x2C ENABLE_CLR_INDEX_REG Enable Clear Index Register 0x34 HINT_ENABLE_SET_INDEX_REG Host Int Enable Set Index Register 0x38 HINT_ENABLE_CLR_INDEX_REG Host Int Enable Clear Index Register 0x200 RAW_STATUS_REG0 Raw Status Register 0 0x204 RAW_STATUS_REG1 Raw Status Register 1 0x208 RAW_STATUS_REG2 Raw Status Register 2 0x20C RAW_STATUS_REG3 Raw Status Register 3 0x210 RAW_STATUS_REG4 Raw Status Register 4 0x214 RAW_STATUS_REG5 Raw Status Register 5 0x218 RAW_STATUS_REG6 Raw Status Register 6 0x21C RAW_STATUS_REG7 Raw Status Register 7 0x220 RAW_STATUS_REG8 Raw Status Register 8 0x224 RAW_STATUS_REG9 Raw Status Register 9 0x228 RAW_STATUS_REG10 Raw Status Register 10 0x22C RAW_STATUS_REG11 Raw Status Register 11 0x230 RAW_STATUS_REG12 Raw Status Register 12 0x234 RAW_STATUS_REG13 Raw Status Register 13 0x238 RAW_STATUS_REG14 Raw Status Register 14 0x23C RAW_STATUS_REG15 Raw Status Register 15 0x280 ENA_STATUS_REG0 Enabled Status Register 0 0x284 ENA_STATUS_REG1 Enabled Status Register 1 0x288 ENA_STATUS_REG2 Enabled Status Register 2 0x28C ENA_STATUS_REG3 Enabled Status Register 3 0x290 ENA_STATUS_REG4 Enabled Status Register 4 0x294 ENA_STATUS_REG5 Enabled Status Register 5 0x298 ENA_STATUS_REG6 Enabled Status Register 6 0x29C ENA_STATUS_REG7 Enabled Status Register 7 0x2A0 ENA_STATUS_REG8 Enabled Status Register 8 0x2A4 ENA_STATUS_REG9 Enabled Status Register 9 0x2A8 ENA_STATUS_REG10 Enabled Status Register10 0x2AC ENA_STATUS_REG11 Enabled Status Register 11 0x2B0 ENA_STATUS_REG12 Enabled Status Register 12 0x2B4 ENA_STATUS_REG13 Enabled Status Register 13 0x2B8 ENA_STATUS_REG14 Enabled Status Register 14 0x2BC ENA_STATUS_REG15 Enabled Status Register 15 140 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-27. CIC0 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x300 ENABLE_REG0 Enable Register 0 0x304 ENABLE_REG1 Enable Register 1 0x308 ENABLE_REG2 Enable Register 2 0x30C ENABLE_REG3 Enable Register 3 0x310 ENABLE_REG4 Enable Register 4 0x314 ENABLE_REG5 Enable Register 5 0x318 ENABLE_REG6 Enable Register 6 0x31C ENABLE_REG7 Enable Register 7 0x320 ENABLE_REG8 Enable Register 8 0x324 ENABLE_REG9 Enable Register 9 0x328 ENABLE_REG10 Enable Register 10 0x32C ENABLE_REG11 Enable Register 11 0x330 ENABLE_REG12 Enable Register 12 0x334 ENABLE_REG13 Enable Register 13 0x338 ENABLE_REG14 Enable Register 14 0x33C ENABLE_REG15 Enable Register 15 0x380 ENABLE_CLR_REG0 Enable Clear Register 0 0x384 ENABLE_CLR_REG1 Enable Clear Register 1 0x388 ENABLE_CLR_REG2 Enable Clear Register 2 0x38C ENABLE_CLR_REG3 Enable Clear Register 3 0x390 ENABLE_CLR_REG4 Enable Clear Register 4 0x394 ENABLE_CLR_REG5 Enable Clear Register 5 0x398 ENABLE_CLR_REG6 Enable Clear Register 6 0x39C ENABLE_CLR_REG7 Enable Clear Register 7 0x3A0 ENABLE_CLR_REG8 Enable Clear Register 8 0x3A4 ENABLE_CLR_REG9 Enable Clear Register 9 0x3A8 ENABLE_CLR_REG10 Enable Clear Register 10 0x3AC ENABLE_CLR_REG11 Enable Clear Register 11 0x3B0 ENABLE_CLR_REG12 Enable Clear Register 12 0x3B4 ENABLE_CLR_REG13 Enable Clear Register 13 0x3B8 ENABLE_CLR_REG14 Enable Clear Register 14 0x38C ENABLE_CLR_REG15 Enable Clear Register 15 0x400 CH_MAP_REG0 Interrupt Channel Map Register for 0 to 0+3 0x404 CH_MAP_REG1 Interrupt Channel Map Register for 4 to 4+3 0x408 CH_MAP_REG2 Interrupt Channel Map Register for 8 to 8+3 0x40C CH_MAP_REG3 Interrupt Channel Map Register for 12 to 12+3 0x410 CH_MAP_REG4 Interrupt Channel Map Register for 16 to 16+3 0x414 CH_MAP_REG5 Interrupt Channel Map Register for 20 to 20+3 0x418 CH_MAP_REG6 Interrupt Channel Map Register for 24 to 24+3 0x41C CH_MAP_REG7 Interrupt Channel Map Register for 28 to 28+3 0x420 CH_MAP_REG8 Interrupt Channel Map Register for 32 to 32+3 0x424 CH_MAP_REG9 Interrupt Channel Map Register for 36 to 36+3 0x428 CH_MAP_REG10 Interrupt Channel Map Register for 40 to 40+3 0x42C CH_MAP_REG11 Interrupt Channel Map Register for 44 to 44+3 0x430 CH_MAP_REG12 Interrupt Channel Map Register for 48 to 48+3 0x434 CH_MAP_REG13 Interrupt Channel Map Register for 52 to 52+3 0x438 CH_MAP_REG14 Interrupt Channel Map Register for 56 to 56+3 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 141 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-27. CIC0 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x43C CH_MAP_REG15 Interrupt Channel Map Register for 60 to 60+3 0x440 CH_MAP_REG16 Interrupt Channel Map Register for 64 to 64+3 0x444 CH_MAP_REG17 Interrupt Channel Map Register for 68 to 68+3 0x448 CH_MAP_REG18 Interrupt Channel Map Register for 72 to 72+3 0x44C CH_MAP_REG19 Interrupt Channel Map Register for 76 to 76+3 0x450 CH_MAP_REG20 Interrupt Channel Map Register for 80 to 80+3 0x454 CH_MAP_REG21 Interrupt Channel Map Register for 84 to 84+3 0x458 CH_MAP_REG22 Interrupt Channel Map Register for 88 to 88+3 0x45C CH_MAP_REG23 Interrupt Channel Map Register for 92 to 92+3 0x460 CH_MAP_REG24 Interrupt Channel Map Register for 96 to 96+3 0x464 CH_MAP_REG25 Interrupt Channel Map Register for 100 to 100+3 0x468 CH_MAP_REG26 Interrupt Channel Map Register for 104 to 104+3 0x46C CH_MAP_REG27 Interrupt Channel Map Register for 108 to 108+3 0x470 CH_MAP_REG28 Interrupt Channel Map Register for 112 to 112+3 0x474 CH_MAP_REG29 Interrupt Channel Map Register for 116 to 116+3 0x478 CH_MAP_REG30 Interrupt Channel Map Register for 120 to 120+3 0x47C CH_MAP_REG31 Interrupt Channel Map Register for 124 to 124+3 0x480 CH_MAP_REG32 Interrupt Channel Map Register for 128 to 128+3 0x484 CH_MAP_REG33 Interrupt Channel Map Register for 132 to 132+3 0x488 CH_MAP_REG34 Interrupt Channel Map Register for 136 to 136+3 0x48C CH_MAP_REG35 Interrupt Channel Map Register for 140 to 140+3 0x490 CH_MAP_REG36 Interrupt Channel Map Register for 144 to 144+3 0x494 CH_MAP_REG37 Interrupt Channel Map Register for 148 to 148+3 0x498 CH_MAP_REG38 Interrupt Channel Map Register for 152 to 152+3 0x49C CH_MAP_REG39 Interrupt Channel Map Register for 156 to 156+3 0x4a0 CH_MAP_REG40 Interrupt Channel Map Register for 160 to 160+3 0x4a4 CH_MAP_REG41 Interrupt Channel Map Register for 164 to 164+3 0x4a8 CH_MAP_REG42 Interrupt Channel Map Register for 168 to 168+3 0x4AC CH_MAP_REG43 Interrupt Channel Map Register for 172 to 172+3 0x4b0 CH_MAP_REG44 Interrupt Channel Map Register for 176 to 176+3 0x4b4 CH_MAP_REG45 Interrupt Channel Map Register for 180 to 180+3 0x4b8 CH_MAP_REG46 Interrupt Channel Map Register for 184 to 184+3 0x4BC CH_MAP_REG47 Interrupt Channel Map Register for 188 to 188+3 0x4C0 CH_MAP_REG48 Interrupt Channel Map Register for 192 to 192+3 0x4C4 CH_MAP_REG49 Interrupt Channel Map Register for 196 to 196+3 0x4C8 CH_MAP_REG50 Interrupt Channel Map Register for 200 to 200+3 0x4CC CH_MAP_REG51 Interrupt Channel Map Register for 204 to 204+3 0x4D0 CH_MAP_REG52 Interrupt Channel Map Register for 208 to 208+3 0x4D4 CH_MAP_REG53 Interrupt Channel Map Register for 212 to 212+3 0x4D8 CH_MAP_REG54 Interrupt Channel Map Register for 216 to 216+3 0x4DC CH_MAP_REG55 Interrupt Channel Map Register for 220 to 220+3 0x4E0 CH_MAP_REG56 Interrupt Channel Map Register for 224 to 224+3 0x4E4 CH_MAP_REG57 Interrupt Channel Map Register for 228 to 228+3 0x4E8 CH_MAP_REG58 Interrupt Channel Map Register for 232 to 232+3 0x4FC CH_MAP_REG59 Interrupt Channel Map Register for 236 to 236+3 0x4F0 CH_MAP_REG60 Interrupt Channel Map Register for 240 to 240+3 0x4F4 CH_MAP_REG61 Interrupt Channel Map Register for 244 to 244+3 142 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-27. CIC0 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x4F8 CH_MAP_REG62 Interrupt Channel Map Register for 248 to 248+3 0x4FC CH_MAP_REG63 Interrupt Channel Map Register for 252 to 252+3 0x500 CH_MAP_REG64 Interrupt Channel Map Register for 256 to 256+3 0x504 CH_MAP_REG65 Interrupt Channel Map Register for 260 to 260+3 0x508 CH_MAP_REG66 Interrupt Channel Map Register for 264 to 264+3 0x50C CH_MAP_REG67 Interrupt Channel Map Register for 268 to 268+3 0x510 CH_MAP_REG68 Interrupt Channel Map Register for 272 to 272+3 0x514 CH_MAP_REG69 Interrupt Channel Map Register for 276 to 276+3 0x518 CH_MAP_REG70 Interrupt Channel Map Register for 280 to 280+3 0x51C CH_MAP_REG71 Interrupt Channel Map Register for 284 to 284+3 0x520 CH_MAP_REG72 Interrupt Channel Map Register for 288 to 288+3 0x524 CH_MAP_REG73 Interrupt Channel Map Register for 292 to 292+3 0x528 CH_MAP_REG74 Interrupt Channel Map Register for 296 to 296+3 0x52C CH_MAP_REG75 Interrupt Channel Map Register for 300 to 300+3 0x520 CH_MAP_REG76 Interrupt Channel Map Register for 304 to 304+3 0x524 CH_MAP_REG77 Interrupt Channel Map Register for 308 to 308+3 0x528 CH_MAP_REG78 Interrupt Channel Map Register for 312 to 312+3 0x52C CH_MAP_REG79 Interrupt Channel Map Register for 316 to 316+3 0x530 CH_MAP_REG80 Interrupt Channel Map Register for 320 to 320+3 0x534 CH_MAP_REG81 Interrupt Channel Map Register for 324 to 324+3 0x538 CH_MAP_REG82 Interrupt Channel Map Register for 328 to 328+3 0x53C CH_MAP_REG83 Interrupt Channel Map Register for 332 to332+3 0x540 CH_MAP_REG84 Interrupt Channel Map Register for336 to 336+3 0x544 CH_MAP_REG85 Interrupt Channel Map Register for 340 to 340+3 0x548 CH_MAP_REG86 Interrupt Channel Map Register for 344 to 344+3 0x54C CH_MAP_REG87 Interrupt Channel Map Register for 348 to 348+3 0x550 CH_MAP_REG88 Interrupt Channel Map Register for 352 to 352+3 0x554 CH_MAP_REG89 Interrupt Channel Map Register for 356 to 356+3 0x558 CH_MAP_REG90 Interrupt Channel Map Register for 360 to 360+3 0x55C CH_MAP_REG91 Interrupt Channel Map Register for 364 to 364+3 0x560 CH_MAP_REG92 Interrupt Channel Map Register for 368 to 368+3 0x564 CH_MAP_REG93 Interrupt Channel Map Register for372 to 372+3 0x568 CH_MAP_REG94 Interrupt Channel Map Register for 376 to 376+3 0x56C CH_MAP_REG95 Interrupt Channel Map Register for 380 to 380+3 0x570 CH_MAP_REG96 Interrupt Channel Map Register for 384 to 384+3 0x574 CH_MAP_REG97 Interrupt Channel Map Register for 388 to 388+3 0x578 CH_MAP_REG98 Interrupt Channel Map Register for 392 to 392+3 0x57C CH_MAP_REG99 Interrupt Channel Map Register for 396 to 396+3 0x580 CH_MAP_REG100 Interrupt Channel Map Register for 400 to 400+3 0x584 CH_MAP_REG101 Interrupt Channel Map Register for 404 to 404+3 0x588 CH_MAP_REG102 Interrupt Channel Map Register for 408 to 408+3 0x58C CH_MAP_REG103 Interrupt Channel Map Register for 412 to412+3 0x590 CH_MAP_REG104 Interrupt Channel Map Register for 416 to 416+3 0x594 CH_MAP_REG105 Interrupt Channel Map Register for 420 to 420+3 0x598 CH_MAP_REG106 Interrupt Channel Map Register for 424 to 424+3 0x59C CH_MAP_REG107 Interrupt Channel Map Register for 428 to 428+3 0x5A0 CH_MAP_REG108 Interrupt Channel Map Register for 432 to 432+3 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 143 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-27. CIC0 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x5A4 CH_MAP_REG109 Interrupt Channel Map Register for 436 to 436+3 0x5A8 CH_MAP_REG110 Interrupt Channel Map Register for 440 to 440+3 0x5AC CH_MAP_REG111 Interrupt Channel Map Register for 444 to 444+3 0x5B0 CH_MAP_REG112 Interrupt Channel Map Register for 448 to 448+3 0x5B4 CH_MAP_REG113 Interrupt Channel Map Register for 452 to 452+3 0x5B8 CH_MAP_REG114 Interrupt Channel Map Register for 456 to 456+3 0x5BC CH_MAP_REG115 Interrupt Channel Map Register for 460 to 460+3 0x5C0 CH_MAP_REG116 Interrupt Channel Map Register for 464 to 464+3 0x5C4 CH_MAP_REG117 Interrupt Channel Map Register for 468 to 468+3 0x5C8 CH_MAP_REG118 Interrupt Channel Map Register for 472 to 472+3 0x5CC CH_MAP_REG119 Interrupt Channel Map Register for 476 to 476+3 0x5D0 CH_MAP_REG120 Interrupt Channel Map Register for 480 to 480+3 0x5D4 CH_MAP_REG121 Interrupt Channel Map Register for 484 to 484+3 0x5D8 CH_MAP_REG122 Interrupt Channel Map Register for 488 to 488+3 0x5DC CH_MAP_REG123 Interrupt Channel Map Register for 482 to 492+3 0x5E0 CH_MAP_REG124 Interrupt Channel Map Register for 496 to 496+3 0x5E4 CH_MAP_REG125 Interrupt Channel Map Register for 500 to 500+3 0x5E8 CH_MAP_REG126 Interrupt Channel Map Register for 504 to 504+3 0x5EC CH_MAP_REG127 Interrupt Channel Map Register for 508 to 508+3 0x5F0 CH_MAP_REG128 Interrupt Channel Map Register for 512 to 512+3 0x5F4 CH_MAP_REG129 Interrupt Channel Map Register for 516 to 516+3 0x5F8 CH_MAP_REG130 Interrupt Channel Map Register for 520 to 520+3 0x5FC CH_MAP_REG131 Interrupt Channel Map Register for 524 to 524+3 0x600 CH_MAP_REG132 Interrupt Channel Map Register for 528 to 528+3 0x604 CH_MAP_REG133 Interrupt Channel Map Register for 532 to 532+3 0x608 CH_MAP_REG134 Interrupt Channel Map Register for 536 to 536+3 0x60C CH_MAP_REG135 Interrupt Channel Map Register for 540 to 540+3 0x610 CH_MAP_REG136 Interrupt Channel Map Register for 544 to 544+3 0x614 CH_MAP_REG137 Interrupt Channel Map Register for 548 to 548+3 0x618 CH_MAP_REG138 Interrupt Channel Map Register for 552 to 552+3 0x61C CH_MAP_REG139 Interrupt Channel Map Register for 556 to 556+3 0x620 CH_MAP_REG140 Interrupt Channel Map Register for 560 to 560+3 0x624 CH_MAP_REG141 Interrupt Channel Map Register for 564 to 564+3 0x628 CH_MAP_REG142 Interrupt Channel Map Register for 568 to 568+3 0x62C CH_MAP_REG143 Interrupt Channel Map Register for 572 to 572+3 0x630 CH_MAP_REG144 Interrupt Channel Map Register for 576 to 576+3 0x634 CH_MAP_REG145 Interrupt Channel Map Register for 580 to 580+3 0x638 CH_MAP_REG146 Interrupt Channel Map Register for 584 to 584+3 0x63C CH_MAP_REG147 Interrupt Channel Map Register for 588 to 588+3 0x640 CH_MAP_REG148 Interrupt Channel Map Register for 592 to 592+3 0x644 CH_MAP_REG149 Interrupt Channel Map Register for 596 to 596+3 0x648 CH_MAP_REG150 Interrupt Channel Map Register for 600 to 600+3 0x64C CH_MAP_REG151 Interrupt Channel Map Register for 604 to 604+3 0x650 CH_MAP_REG152 Interrupt Channel Map Register for 608 to 608+3 0x654 CH_MAP_REG153 Interrupt Channel Map Register for 612 to 612+3 0x658 CH_MAP_REG154 Interrupt Channel Map Register for 616 to 616+3 0x65C CH_MAP_REG155 Interrupt Channel Map Register for 620 to 620+3 144 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-27. CIC0 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x660 CH_MAP_REG156 Interrupt Channel Map Register for 624 to 624+3 0x664 CH_MAP_REG157 Interrupt Channel Map Register for 628 to 628+3 0x668 CH_MAP_REG158 Interrupt Channel Map Register for 632 to 632+3 0x66C CH_MAP_REG159 Interrupt Channel Map Register for 636 to 636+3 0x670 CH_MAP_REG160 Interrupt Channel Map Register for 640 to 640+3 0x674 CH_MAP_REG161 Interrupt Channel Map Register for 644 to 644+3 0x678 CH_MAP_REG162 Interrupt Channel Map Register for 648 to 648+3 0x67C CH_MAP_REG163 Interrupt Channel Map Register for 652 to 652+3 0x680 CH_MAP_REG164 Interrupt Channel Map Register for 656 to 656+3 0x684 CH_MAP_REG165 Interrupt Channel Map Register for 660 to 660+3 0x688 CH_MAP_REG166 Interrupt Channel Map Register for 664 to 664+3 0x68C CH_MAP_REG167 Interrupt Channel Map Register for 668 to 668+3 0x690 CH_MAP_REG168 Interrupt Channel Map Register for 672 to 672+3 0x694 CH_MAP_REG169 Interrupt Channel Map Register for 676 to 676+3 0x698 CH_MAP_REG170 Interrupt Channel Map Register for 680 to 680+3 0x69C CH_MAP_REG171 Interrupt Channel Map Register for 684 to 684+3 0x800 HINT_MAP_REG0 Host Interrupt Map Register for 0 to 0+3 0x804 HINT_MAP_REG1 Host Interrupt Map Register for 4 to 4+3 0x808 HINT_MAP_REG2 Host Interrupt Map Register for 8 to 8+3 0x80C HINT_MAP_REG3 Host Interrupt Map Register for 12 to 12+3 0x810 HINT_MAP_REG4 Host Interrupt Map Register for 16 to 16+3 0x814 HINT_MAP_REG5 Host Interrupt Map Register for 20 to 20+3 0x818 HINT_MAP_REG6 Host Interrupt Map Register for 24 to 24+3 0x81C HINT_MAP_REG7 Host Interrupt Map Register for 28 to 28+3 0x820 HINT_MAP_REG8 Host Interrupt Map Register for 32 to 32+3 0x824 HINT_MAP_REG9 Host Interrupt Map Register for 36 to 36+3 0x828 HINT_MAP_REG10 Host Interrupt Map Register for 40 to 40+3 0x82C HINT_MAP_REG11 Host Interrupt Map Register for 44 to 44+3 0x830 HINT_MAP_REG12 Host Interrupt Map Register for 48 to 48+3 0x834 HINT_MAP_REG13 Host Interrupt Map Register for 52 to 52+3 0x838 HINT_MAP_REG14 Host Interrupt Map Register for 56 to 56+3 0x83C HINT_MAP_REG15 Host Interrupt Map Register for 60 to 60+3 0x840 HINT_MAP_REG16 Host Interrupt Map Register for 64 to 64+3 0x844 HINT_MAP_REG17 Host Interrupt Map Register for 68 to 68+3 0x848 HINT_MAP_REG18 Host Interrupt Map Register for 72 to 72+3 0x84C HINT_MAP_REG19 Host Interrupt Map Register for 76 to 76+3 0x1500 ENABLE_HINT_REG0 Host Int Enable Register 0 0x1504 ENABLE_HINT_REG1 Host Int Enable Register 1 0x1508 ENABLE_HINT_REG2 Host Int Enable Register 2 8.3.2.2 CIC1 Register Map Table 8-28. CIC1 Registers ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x0 REVISION_REG Revision Register 0x10 GLOBAL_ENABLE_HINT_REG Global Host Interrupt Enable Register Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 145 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x20 STATUS_SET_INDEX_REG Status Set Index Register 0x24 STATUS_CLR_INDEX_REG Status Clear Index Register 0x28 ENABLE_SET_INDEX_REG Enable Set Index Register 0x2C ENABLE_CLR_INDEX_REG Enable Clear Index Register 0x34 HINT_ENABLE_SET_INDEX_REG Host Interrupt Enable Set Index Register 0x38 HINT_ENABLE_CLR_INDEX_REG Host Interrupt Enable Clear Index Register 0x200 RAW_STATUS_REG0 Raw Status Register 0 0x204 RAW_STATUS_REG1 Raw Status Register 1 0x208 RAW_STATUS_REG2 Raw Status Register 2 0x20C RAW_STATUS_REG3 Raw Status Register 3 0x210 RAW_STATUS_REG4 Raw Status Register 4 0x214 RAW_STATUS_REG5 Raw Status Register 5 0x218 RAW_STATUS_REG6 Raw Status Register 6 0x21C RAW_STATUS_REG7 Raw Status Register 7 0x220 RAW_STATUS_REG8 Raw Status Register 8 0x224 RAW_STATUS_REG9 Raw Status Register 9 0x228 RAW_STATUS_REG10 Raw Status Register 10 0x22C RAW_STATUS_REG11 Raw Status Register 11 0x230 RAW_STATUS_REG12 Raw Status Register 12 0x234 RAW_STATUS_REG13 Raw Status Register 13 0x238 RAW_STATUS_REG14 Raw Status Register 14 0x23C RAW_STATUS_REG15 Raw Status Register 15 0x280 ENA_STATUS_REG0 Enabled Status Register 0 0x284 ENA_STATUS_REG1 Enabled Status Register 1 0x288 ENA_STATUS_REG2 Enabled Status Register 2 0x28C ENA_STATUS_REG3 Enabled Status Register 3 0x290 ENA_STATUS_REG4 Enabled Status Register 4 0x294 ENA_STATUS_REG5 Enabled Status Register 5 0x298 ENA_STATUS_REG6 Enabled Status Register 6 0x29C ENA_STATUS_REG7 Enabled Status Register 7 0x2A0 ENA_STATUS_REG8 Enabled Status Register 8 0x2A4 ENA_STATUS_REG9 Enabled Status Register 9 0x2A8 ENA_STATUS_REG10 Enabled Status Register10 0x2AC ENA_STATUS_REG11 Enabled Status Register 11 0x2B0 ENA_STATUS_REG12 Enabled Status Register 12 0x2B4 ENA_STATUS_REG13 Enabled Status Register 13 0x2B8 ENA_STATUS_REG14 Enabled Status Register 14 0x2BC ENA_STATUS_REG15 Enabled Status Register 15 0x300 ENABLE_REG0 Enable Register 0 0x304 ENABLE_REG1 Enable Register 1 0x308 ENABLE_REG2 Enable Register 2 0x30C ENABLE_REG3 Enable Register 3 0x310 ENABLE_REG4 Enable Register 4 0x314 ENABLE_REG5 Enable Register 5 0x318 ENABLE_REG6 Enable Register 6 0x31C ENABLE_REG7 Enable Register 7 0x320 ENABLE_REG8 Enable Register 8 146 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x324 ENABLE_REG9 Enable Register 9 0x328 ENABLE_REG10 Enable Register 10 0x32C ENABLE_REG11 Enable Register 11 0x330 ENABLE_REG12 Enable Register 12 0x334 ENABLE_REG13 Enable Register 13 0x338 ENABLE_REG14 Enable Register 14 0x33C ENABLE_REG15 Enable Register 15 0x380 ENABLE_CLR_REG0 Enable Clear Register 0 0x384 ENABLE_CLR_REG1 Enable Clear Register 1 0x388 ENABLE_CLR_REG2 Enable Clear Register 2 0x38C ENABLE_CLR_REG3 Enable Clear Register 3 0x390 ENABLE_CLR_REG4 Enable Clear Register 4 0x394 ENABLE_CLR_REG5 Enable Clear Register 5 0x398 ENABLE_CLR_REG6 Enable Clear Register 6 0x39C ENABLE_CLR_REG7 Enable Clear Register 7 0x3A0 ENABLE_CLR_REG8 Enable Clear Register 8 0x3A4 ENABLE_CLR_REG9 Enable Clear Register 9 0x3A8 ENABLE_CLR_REG10 Enable Clear Register 10 0x3AC ENABLE_CLR_REG11 Enable Clear Register 11 0x3B0 ENABLE_CLR_REG12 Enable Clear Register 12 0x3B4 ENABLE_CLR_REG13 Enable Clear Register 13 0x3B8 ENABLE_CLR_REG14 Enable Clear Register 14 0x38C ENABLE_CLR_REG15 Enable Clear Register 15 0x400 CH_MAP_REG0 Interrupt Channel Map Register for 0 to 0+3 0x404 CH_MAP_REG1 Interrupt Channel Map Register for 4 to 4+3 0x408 CH_MAP_REG2 Interrupt Channel Map Register for 8 to 8+3 0x40C CH_MAP_REG3 Interrupt Channel Map Register for 12 to 12+3 0x410 CH_MAP_REG4 Interrupt Channel Map Register for 16 to 16+3 0x414 CH_MAP_REG5 Interrupt Channel Map Register for 20 to 20+3 0x418 CH_MAP_REG6 Interrupt Channel Map Register for 24 to 24+3 0x41C CH_MAP_REG7 Interrupt Channel Map Register for 28 to 28+3 0x420 CH_MAP_REG8 Interrupt Channel Map Register for 32 to 32+3 0x424 CH_MAP_REG9 Interrupt Channel Map Register for 36 to 36+3 0x428 CH_MAP_REG10 Interrupt Channel Map Register for 40 to 40+3 0x42C CH_MAP_REG11 Interrupt Channel Map Register for 44 to 44+3 0x430 CH_MAP_REG12 Interrupt Channel Map Register for 48 to 48+3 0x434 CH_MAP_REG13 Interrupt Channel Map Register for 52 to 52+3 0x438 CH_MAP_REG14 Interrupt Channel Map Register for 56 to 56+3 0x43C CH_MAP_REG15 Interrupt Channel Map Register for 60 to 60+3 0x440 CH_MAP_REG16 Interrupt Channel Map Register for 64 to 64+3 0x444 CH_MAP_REG17 Interrupt Channel Map Register for 68 to 68+3 0x448 CH_MAP_REG18 Interrupt Channel Map Register for 72 to 72+3 0x44C CH_MAP_REG19 Interrupt Channel Map Register for 76 to 76+3 0x450 CH_MAP_REG20 Interrupt Channel Map Register for 80 to 80+3 0x454 CH_MAP_REG21 Interrupt Channel Map Register for 84 to 84+3 0x458 CH_MAP_REG22 Interrupt Channel Map Register for 88 to 88+3 0x45C CH_MAP_REG23 Interrupt Channel Map Register for 92 to 92+3 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 147 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x460 CH_MAP_REG24 Interrupt Channel Map Register for 96 to 96+3 0x464 CH_MAP_REG25 Interrupt Channel Map Register for 100 to 100+3 0x468 CH_MAP_REG26 Interrupt Channel Map Register for 104 to 104+3 0x46C CH_MAP_REG27 Interrupt Channel Map Register for 108 to 108+3 0x470 CH_MAP_REG28 Interrupt Channel Map Register for 112 to 112+3 0x474 CH_MAP_REG29 Interrupt Channel Map Register for 116 to 116+3 0x478 CH_MAP_REG30 Interrupt Channel Map Register for 120 to 120+3 0x47C CH_MAP_REG31 Interrupt Channel Map Register for 124 to 124+3 0x480 CH_MAP_REG32 Interrupt Channel Map Register for 128 to 128+3 0x484 CH_MAP_REG33 Interrupt Channel Map Register for 132 to 132+3 0x488 CH_MAP_REG34 Interrupt Channel Map Register for 136 to 136+3 0x48C CH_MAP_REG35 Interrupt Channel Map Register for 140 to 140+3 0x490 CH_MAP_REG36 Interrupt Channel Map Register for 144 to 144+3 0x494 CH_MAP_REG37 Interrupt Channel Map Register for 148 to 148+3 0x498 CH_MAP_REG38 Interrupt Channel Map Register for 152 to 152+3 0x49C CH_MAP_REG39 Interrupt Channel Map Register for 156 to 156+3 0x4A0 CH_MAP_REG40 Interrupt Channel Map Register for 160 to 160+3 0x4A4 CH_MAP_REG41 Interrupt Channel Map Register for 164 to 164+3 0x4A8 CH_MAP_REG42 Interrupt Channel Map Register for 168 to 168+3 0x4AC CH_MAP_REG43 Interrupt Channel Map Register for 172 to 172+3 0x4B0 CH_MAP_REG44 Interrupt Channel Map Register for 176 to 176+3 0x4B4 CH_MAP_REG45 Interrupt Channel Map Register for 180 to 180+3 0x4B8 CH_MAP_REG46 Interrupt Channel Map Register for 184 to 184+3 0x4BC CH_MAP_REG47 Interrupt Channel Map Register for 188 to 188+3 0x4C0 CH_MAP_REG48 Interrupt Channel Map Register for 192 to 192+3 0x4C4 CH_MAP_REG49 Interrupt Channel Map Register for 196 to 196+3 0x4C8 CH_MAP_REG50 Interrupt Channel Map Register for 200 to 200+3 0x4CC CH_MAP_REG51 Interrupt Channel Map Register for 204 to 204+3 0x4D0 CH_MAP_REG52 Interrupt Channel Map Register for 208 to 208+3 0x4D4 CH_MAP_REG53 Interrupt Channel Map Register for 212 to 212+3 0x4D8 CH_MAP_REG54 Interrupt Channel Map Register for 216 to 216+3 0x4DC CH_MAP_REG55 Interrupt Channel Map Register for 220 to 220+3 0x4E0 CH_MAP_REG56 Interrupt Channel Map Register for 224 to 224+3 0x4E4 CH_MAP_REG57 Interrupt Channel Map Register for 228 to 228+3 0x4E8 CH_MAP_REG58 Interrupt Channel Map Register for 232 to 232+3 0x4FC CH_MAP_REG59 Interrupt Channel Map Register for 236 to 236+3 0x4F0 CH_MAP_REG60 Interrupt Channel Map Register for 240 to 240+3 0x4F4 CH_MAP_REG61 Interrupt Channel Map Register for 244 to 244+3 0x4F8 CH_MAP_REG62 Interrupt Channel Map Register for 248 to 248+3 0x4FC CH_MAP_REG63 Interrupt Channel Map Register for 252 to 252+3 0x500 CH_MAP_REG64 Interrupt Channel Map Register for 256 to 256+3 0x504 CH_MAP_REG65 Interrupt Channel Map Register for 260 to 260+3 0x508 CH_MAP_REG66 Interrupt Channel Map Register for 264 to 264+3 0x50C CH_MAP_REG67 Interrupt Channel Map Register for 268 to 268+3 0x510 CH_MAP_REG68 Interrupt Channel Map Register for 272 to 272+3 0x514 CH_MAP_REG69 Interrupt Channel Map Register for 276 to 276+3 0x518 CH_MAP_REG70 Interrupt Channel Map Register for 280 to 280+3 148 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x51C CH_MAP_REG71 Interrupt Channel Map Register for 284 to 284+3 0x520 CH_MAP_REG72 Interrupt Channel Map Register for 288 to 288+3 0x524 CH_MAP_REG73 Interrupt Channel Map Register for 292 to 292+3 0x528 CH_MAP_REG74 Interrupt Channel Map Register for 296 to 296+3 0x52C CH_MAP_REG75 Interrupt Channel Map Register for 300 to 300+3 0x520 CH_MAP_REG76 Interrupt Channel Map Register for 304 to 304+3 0x524 CH_MAP_REG77 Interrupt Channel Map Register for 308 to 308+3 0x528 CH_MAP_REG78 Interrupt Channel Map Register for 312 to 312+3 0x52C CH_MAP_REG79 Interrupt Channel Map Register for 316 to 316+3 0x530 CH_MAP_REG80 Interrupt Channel Map Register for 320 to 320+3 0x534 CH_MAP_REG81 Interrupt Channel Map Register for 324 to 324+3 0x538 CH_MAP_REG82 Interrupt Channel Map Register for 328 to 328+3 0x53C CH_MAP_REG83 Interrupt Channel Map Register for 332 to332+3 0x540 CH_MAP_REG84 Interrupt Channel Map Register for336 to 336+3 0x544 CH_MAP_REG85 Interrupt Channel Map Register for 340 to 340+3 0x548 CH_MAP_REG86 Interrupt Channel Map Register for 344 to 344+3 0x54C CH_MAP_REG87 Interrupt Channel Map Register for 348 to 348+3 0x550 CH_MAP_REG88 Interrupt Channel Map Register for 352 to 352+3 0x554 CH_MAP_REG89 Interrupt Channel Map Register for 356 to 356+3 0x558 CH_MAP_REG90 Interrupt Channel Map Register for 360 to 360+3 0x55C CH_MAP_REG91 Interrupt Channel Map Register for 364 to 364+3 0x560 CH_MAP_REG92 Interrupt Channel Map Register for 368 to 368+3 0x564 CH_MAP_REG93 Interrupt Channel Map Register for372 to 372+3 0x568 CH_MAP_REG94 Interrupt Channel Map Register for 376 to 376+3 0x56C CH_MAP_REG95 Interrupt Channel Map Register for 380 to 380+3 0x570 CH_MAP_REG96 Interrupt Channel Map Register for 384 to 384+3 0x574 CH_MAP_REG97 Interrupt Channel Map Register for 388 to 388+3 0x578 CH_MAP_REG98 Interrupt Channel Map Register for 392 to 392+3 0x57C CH_MAP_REG99 Interrupt Channel Map Register for 396 to 396+3 0x580 CH_MAP_REG100 Interrupt Channel Map Register for 400 to 400+3 0x584 CH_MAP_REG101 Interrupt Channel Map Register for 404 to 404+3 0x588 CH_MAP_REG102 Interrupt Channel Map Register for 408 to 408+3 0x58C CH_MAP_REG103 Interrupt Channel Map Register for 412 to412+3 0x590 CH_MAP_REG104 Interrupt Channel Map Register for 416 to 416+3 0x594 CH_MAP_REG105 Interrupt Channel Map Register for 420 to 420+3 0x598 CH_MAP_REG106 Interrupt Channel Map Register for 424 to 424+3 0x59C CH_MAP_REG107 Interrupt Channel Map Register for 428 to 428+3 0x5A0 CH_MAP_REG108 Interrupt Channel Map Register for 432 to 432+3 0x5A4 CH_MAP_REG109 Interrupt Channel Map Register for 436 to 436+3 0x5A8 CH_MAP_REG110 Interrupt Channel Map Register for 440 to 440+3 0x5AC CH_MAP_REG111 Interrupt Channel Map Register for 444 to 444+3 0x5B0 CH_MAP_REG112 Interrupt Channel Map Register for 448 to 448+3 0x5B4 CH_MAP_REG113 Interrupt Channel Map Register for 452 to 452+3 0x5B8 CH_MAP_REG114 Interrupt Channel Map Register for 456 to 456+3 0x5BC CH_MAP_REG115 Interrupt Channel Map Register for 460 to 460+3 0x5C0 CH_MAP_REG116 Interrupt Channel Map Register for 464 to 464+3 0x5C4 CH_MAP_REG117 Interrupt Channel Map Register for 468 to 468+3 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 149 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x5C8 CH_MAP_REG118 Interrupt Channel Map Register for 472 to 472+3 0x5CC CH_MAP_REG119 Interrupt Channel Map Register for 476 to 476+3 0x5D0 CH_MAP_REG120 Interrupt Channel Map Register for 480 to 480+3 0x5D4 CH_MAP_REG121 Interrupt Channel Map Register for 484 to 484+3 0x5D8 CH_MAP_REG122 Interrupt Channel Map Register for 488 to 488+3 0x5DC CH_MAP_REG123 Interrupt Channel Map Register for 482 to 492+3 0x5E0 CH_MAP_REG124 Interrupt Channel Map Register for 496 to 496+3 0x5E4 CH_MAP_REG125 Interrupt Channel Map Register for 500 to 500+3 0x5E8 CH_MAP_REG126 Interrupt Channel Map Register for 504 to 504+3 0x5EC CH_MAP_REG127 Interrupt Channel Map Register for 508 to 508+3 0x5F0 CH_MAP_REG128 Interrupt Channel Map Register for 512 to 512+3 0x5F4 CH_MAP_REG129 Interrupt Channel Map Register for 516 to 516+3 0x5F8 CH_MAP_REG130 Interrupt Channel Map Register for 520 to 520+3 0x5FC CH_MAP_REG131 Interrupt Channel Map Register for 524 to 524+3 0x600 CH_MAP_REG132 Interrupt Channel Map Register for 528 to 528+3 0x604 CH_MAP_REG133 Interrupt Channel Map Register for 532 to 532+3 0x608 CH_MAP_REG134 Interrupt Channel Map Register for 536 to 536+3 0x60C CH_MAP_REG135 Interrupt Channel Map Register for 540 to 540+3 0x610 CH_MAP_REG136 Interrupt Channel Map Register for 544 to 544+3 0x614 CH_MAP_REG137 Interrupt Channel Map Register for 548 to 548+3 0x618 CH_MAP_REG138 Interrupt Channel Map Register for 552 to 552+3 0x61C CH_MAP_REG139 Interrupt Channel Map Register for 556 to 556+3 0x620 CH_MAP_REG140 Interrupt Channel Map Register for 560 to 560+3 0x624 CH_MAP_REG141 Interrupt Channel Map Register for 564 to 564+3 0x628 CH_MAP_REG142 Interrupt Channel Map Register for 568 to 568+3 0x62C CH_MAP_REG143 Interrupt Channel Map Register for 572 to 572+3 0x630 CH_MAP_REG144 Interrupt Channel Map Register for 576 to 576+3 0x634 CH_MAP_REG145 Interrupt Channel Map Register for 580 to 580+3 0x638 CH_MAP_REG146 Interrupt Channel Map Register for 584 to 584+3 0x63C CH_MAP_REG147 Interrupt Channel Map Register for 588 to 588+3 0x640 CH_MAP_REG148 Interrupt Channel Map Register for 592 to 592+3 0x644 CH_MAP_REG149 Interrupt Channel Map Register for 596 to 596+3 0x648 CH_MAP_REG150 Interrupt Channel Map Register for 600 to 600+3 0x64C CH_MAP_REG151 Interrupt Channel Map Register for 604 to 604+3 0x650 CH_MAP_REG152 Interrupt Channel Map Register for 608 to 608+3 0x654 CH_MAP_REG153 Interrupt Channel Map Register for 612 to 612+3 0x658 CH_MAP_REG154 Interrupt Channel Map Register for 616 to 616+3 0x65C CH_MAP_REG155 Interrupt Channel Map Register for 620 to 620+3 0x660 CH_MAP_REG156 Interrupt Channel Map Register for 624 to 624+3 0x664 CH_MAP_REG157 Interrupt Channel Map Register for 628 to 628+3 0x668 CH_MAP_REG158 Interrupt Channel Map Register for 632 to 632+3 0x66C CH_MAP_REG159 Interrupt Channel Map Register for 636 to 636+3 0x670 CH_MAP_REG160 Interrupt Channel Map Register for 640 to 640+3 0x674 CH_MAP_REG161 Interrupt Channel Map Register for 644 to 644+3 0x678 CH_MAP_REG162 Interrupt Channel Map Register for 648 to 648+3 0x67C CH_MAP_REG163 Interrupt Channel Map Register for 652 to 652+3 0x680 CH_MAP_REG164 Interrupt Channel Map Register for 656 to 656+3 150 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-28. CIC1 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x684 CH_MAP_REG165 Interrupt Channel Map Register for 660 to 660+3 0x688 CH_MAP_REG166 Interrupt Channel Map Register for 664 to 664+3 0x68C CH_MAP_REG167 Interrupt Channel Map Register for 668 to 668+3 0x690 CH_MAP_REG168 Interrupt Channel Map Register for 672 to 672+3 0x694 CH_MAP_REG169 Interrupt Channel Map Register for 676 to 676+3 0x698 CH_MAP_REG170 Interrupt Channel Map Register for 680 to 680+3 0x69C CH_MAP_REG171 Interrupt Channel Map Register for 684 to 684+3 0x800 HINT_MAP_REG0 Host Interrupt Map Register for 0 to 0+3 0x804 HINT_MAP_REG1 Host Interrupt Map Register for 4 to 4+3 0x808 HINT_MAP_REG2 Host Interrupt Map Register for 8 to 8+3 0x80C HINT_MAP_REG3 Host Interrupt Map Register for 12 to 12+3 0x810 HINT_MAP_REG4 Host Interrupt Map Register for 16 to 16+3 0x814 HINT_MAP_REG5 Host Interrupt Map Register for 20 to 20+3 0x818 HINT_MAP_REG6 Host Interrupt Map Register for 24 to 24+3 0x81C HINT_MAP_REG7 Host Interrupt Map Register for 28 to 28+3 0x820 HINT_MAP_REG8 Host Interrupt Map Register for 32 to 32+3 0x824 HINT_MAP_REG9 Host Interrupt Map Register for 36 to 36+3 0x828 HINT_MAP_REG10 Host Interrupt Map Register for 40 to 40+3 0x82C HINT_MAP_REG11 Host Interrupt Map Register for 44 to 44+3 0x830 HINT_MAP_REG12 Host Interrupt Map Register for 48 to 48+3 0x834 HINT_MAP_REG13 Host Interrupt Map Register for 52 to 52+3 0x1500 ENABLE_HINT_REG0 Host Interrupt Enable Register 0 0x1504 ENABLE_HINT_REG1 Host Interrupt Enable Register 1 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 151 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 8.3.2.3 www.ti.com CIC2 Register Map Table 8-29. CIC2 Registers ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x0 REVISION_REG Revision Register 0x10 GLOBAL_ENABLE_HINT_REG Global Host Int Enable Register 0x20 STATUS_SET_INDEX_REG Status Set Index Register 0x24 STATUS_CLR_INDEX_REG Status Clear Index Register 0x28 ENABLE_SET_INDEX_REG Enable Set Index Register 0x2C ENABLE_CLR_INDEX_REG Enable Clear Index Register 0x34 HINT_ENABLE_SET_INDEX_REG Host Int Enable Set Index Register 0x38 HINT_ENABLE_CLR_INDEX_REG Host Int Enable Clear Index Register 0x200 RAW_STATUS_REG0 Raw Status Register 0 0x204 RAW_STATUS_REG1 Raw Status Register 1 0x208 RAW_STATUS_REG2 Raw Status Register 2 0x20C RAW_STATUS_REG3 Raw Status Register 3 0x210 RAW_STATUS_REG4 Raw Status Register 4 0x214 RAW_STATUS_REG5 Raw Status Register 5 0x218 RAW_STATUS_REG6 Raw Status Register 6 0x21C RAW_STATUS_REG7 Raw Status Register 7 0x220 RAW_STATUS_REG8 Raw Status Register 8 0x224 RAW_STATUS_REG9 Raw Status Register 9 0x228 RAW_STATUS_REG10 Raw Status Register 10 0x22C RAW_STATUS_REG11 Raw Status Register 11 0x230 RAW_STATUS_REG12 Raw Status Register 12 0x234 RAW_STATUS_REG13 Raw Status Register 13 0x238 RAW_STATUS_REG14 Raw Status Register 14 0x23C RAW_STATUS_REG15 Raw Status Register 15 0x280 ENA_STATUS_REG0 Enabled Status Register 0 0x284 ENA_STATUS_REG1 Enabled Status Register 1 0x288 ENA_STATUS_REG2 Enabled Status Register 2 0x28C ENA_STATUS_REG3 Enabled Status Register 3 0x290 ENA_STATUS_REG4 Enabled Status Register 4 0x294 ENA_STATUS_REG5 Enabled Status Register 5 0x298 ENA_STATUS_REG6 Enabled Status Register 6 0x29C ENA_STATUS_REG7 Enabled Status Register 7 0x2A0 ENA_STATUS_REG8 Enabled Status Register 8 0x2A4 ENA_STATUS_REG9 Enabled Status Register 9 0x2A8 ENA_STATUS_REG10 Enabled Status Register10 0x2AC ENA_STATUS_REG11 Enabled Status Register 11 0x2B0 ENA_STATUS_REG12 Enabled Status Register 12 0x2B4 ENA_STATUS_REG13 Enabled Status Register 13 0x2B8 ENA_STATUS_REG14 Enabled Status Register 14 0x2BC ENA_STATUS_REG15 Enabled Status Register 15 0x300 ENABLE_REG0 Enable Register 0 0x304 ENABLE_REG1 Enable Register 1 0x308 ENABLE_REG2 Enable Register 2 0x30C ENABLE_REG3 Enable Register 3 0x310 ENABLE_REG4 Enable Register 4 152 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-29. CIC2 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x314 ENABLE_REG5 Enable Register 5 0x318 ENABLE_REG6 Enable Register 6 0x31C ENABLE_REG7 Enable Register 7 0x320 ENABLE_REG8 Enable Register 8 0x324 ENABLE_REG9 Enable Register 9 0x328 ENABLE_REG10 Enable Register 10 0x32C ENABLE_REG11 Enable Register 11 0x330 ENABLE_REG12 Enable Register 12 0x334 ENABLE_REG13 Enable Register 13 0x338 ENABLE_REG14 Enable Register 14 0x33C ENABLE_REG15 Enable Register 15 0x380 ENABLE_CLR_REG0 Enable Clear Register 0 0x384 ENABLE_CLR_REG1 Enable Clear Register 1 0x388 ENABLE_CLR_REG2 Enable Clear Register 2 0x38C ENABLE_CLR_REG3 Enable Clear Register 3 0x390 ENABLE_CLR_REG4 Enable Clear Register 4 0x394 ENABLE_CLR_REG5 Enable Clear Register 5 0x398 ENABLE_CLR_REG6 Enable Clear Register 6 0x39C ENABLE_CLR_REG7 Enable Clear Register 7 0x3A0 ENABLE_CLR_REG8 Enable Clear Register 8 0x3A4 ENABLE_CLR_REG9 Enable Clear Register 9 0x3A8 ENABLE_CLR_REG10 Enable Clear Register 10 0x3AC ENABLE_CLR_REG11 Enable Clear Register 11 0x3B0 ENABLE_CLR_REG12 Enable Clear Register 12 0x3B4 ENABLE_CLR_REG13 Enable Clear Register 13 0x3B8 ENABLE_CLR_REG14 Enable Clear Register 14 0x38C ENABLE_CLR_REG15 Enable Clear Register 15 0x400 CH_MAP_REG0 Interrupt Channel Map Register for 0 to 0+3 0x404 CH_MAP_REG1 Interrupt Channel Map Register for 4 to 4+3 0x408 CH_MAP_REG2 Interrupt Channel Map Register for 8 to 8+3 0x40C CH_MAP_REG3 Interrupt Channel Map Register for 12 to 12+3 0x410 CH_MAP_REG4 Interrupt Channel Map Register for 16 to 16+3 0x414 CH_MAP_REG5 Interrupt Channel Map Register for 20 to 20+3 0x418 CH_MAP_REG6 Interrupt Channel Map Register for 24 to 24+3 0x41C CH_MAP_REG7 Interrupt Channel Map Register for 28 to 28+3 0x420 CH_MAP_REG8 Interrupt Channel Map Register for 32 to 32+3 0x424 CH_MAP_REG9 Interrupt Channel Map Register for 36 to 36+3 0x428 CH_MAP_REG10 Interrupt Channel Map Register for 40 to 40+3 0x42C CH_MAP_REG11 Interrupt Channel Map Register for 44 to 44+3 0x430 CH_MAP_REG12 Interrupt Channel Map Register for 48 to 48+3 0x434 CH_MAP_REG13 Interrupt Channel Map Register for 52 to 52+3 0x438 CH_MAP_REG14 Interrupt Channel Map Register for 56 to 56+3 0x43C CH_MAP_REG15 Interrupt Channel Map Register for 60 to 60+3 0x5C0 CH_MAP_REG116 Interrupt Channel Map Register for 464 to 464+3 0x5C4 CH_MAP_REG117 Interrupt Channel Map Register for 468 to 468+3 0x5C8 CH_MAP_REG118 Interrupt Channel Map Register for 472 to 472+3 0x5CC CH_MAP_REG119 Interrupt Channel Map Register for 476 to 476+3 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 153 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-29. CIC2 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x5D0 CH_MAP_REG120 Interrupt Channel Map Register for 480 to 480+3 0x5D4 CH_MAP_REG121 Interrupt Channel Map Register for 484 to 484+3 0x5D8 CH_MAP_REG122 Interrupt Channel Map Register for 488 to 488+3 0x5DC CH_MAP_REG123 Interrupt Channel Map Register for 482 to 492+3 0x5E0 CH_MAP_REG124 Interrupt Channel Map Register for 496 to 496+3 0x5E4 CH_MAP_REG125 Interrupt Channel Map Register for 500 to 500+3 0x5E8 CH_MAP_REG126 Interrupt Channel Map Register for 504 to 504+3 0x5EC CH_MAP_REG127 Interrupt Channel Map Register for 508 to 508+3 0x5F0 CH_MAP_REG128 Interrupt Channel Map Register for 512 to 512+3 0x5F4 CH_MAP_REG129 Interrupt Channel Map Register for 516 to 516+3 0x5F8 CH_MAP_REG130 Interrupt Channel Map Register for 520 to 520+3 0x5FC CH_MAP_REG131 Interrupt Channel Map Register for 524 to 524+3 0x600 CH_MAP_REG132 Interrupt Channel Map Register for 528 to 528+3 0x604 CH_MAP_REG133 Interrupt Channel Map Register for 532 to 532+3 0x608 CH_MAP_REG134 Interrupt Channel Map Register for 536 to 536+3 0x60C CH_MAP_REG135 Interrupt Channel Map Register for 540 to 540+3 0x610 CH_MAP_REG136 Interrupt Channel Map Register for 544 to 544+3 0x614 CH_MAP_REG137 Interrupt Channel Map Register for 548 to 548+3 0x618 CH_MAP_REG138 Interrupt Channel Map Register for 552 to 552+3 0x61C CH_MAP_REG139 Interrupt Channel Map Register for 556 to 556+3 0x620 CH_MAP_REG140 Interrupt Channel Map Register for 560 to 560+3 0x624 CH_MAP_REG141 Interrupt Channel Map Register for 564 to 564+3 0x628 CH_MAP_REG142 Interrupt Channel Map Register for 568 to 568+3 0x62C CH_MAP_REG143 Interrupt Channel Map Register for 572 to 572+3 0x630 CH_MAP_REG144 Interrupt Channel Map Register for 576 to 576+3 0x634 CH_MAP_REG145 Interrupt Channel Map Register for 580 to 580+3 0x638 CH_MAP_REG146 Interrupt Channel Map Register for 584 to 584+3 0x63C CH_MAP_REG147 Interrupt Channel Map Register for 588 to 588+3 0x640 CH_MAP_REG148 Interrupt Channel Map Register for 592 to 592+3 0x644 CH_MAP_REG149 Interrupt Channel Map Register for 596 to 596+3 0x648 CH_MAP_REG150 Interrupt Channel Map Register for 600 to 600+3 0x64C CH_MAP_REG151 Interrupt Channel Map Register for 604 to 604+3 0x650 CH_MAP_REG152 Interrupt Channel Map Register for 608 to 608+3 0x654 CH_MAP_REG153 Interrupt Channel Map Register for 612 to 612+3 0x658 CH_MAP_REG154 Interrupt Channel Map Register for 616 to 616+3 0x65C CH_MAP_REG155 Interrupt Channel Map Register for 620 to 620+3 0x660 CH_MAP_REG156 Interrupt Channel Map Register for 624 to 624+3 0x664 CH_MAP_REG157 Interrupt Channel Map Register for 628 to 628+3 0x668 CH_MAP_REG158 Interrupt Channel Map Register for 632 to 632+3 0x66C CH_MAP_REG159 Interrupt Channel Map Register for 636 to 636+3 0x670 CH_MAP_REG160 Interrupt Channel Map Register for 640 to 640+3 0x674 CH_MAP_REG161 Interrupt Channel Map Register for 644 to 644+3 0x678 CH_MAP_REG162 Interrupt Channel Map Register for 648 to 648+3 0x67C CH_MAP_REG163 Interrupt Channel Map Register for 652 to 652+3 0x680 CH_MAP_REG164 Interrupt Channel Map Register for 656 to 656+3 0x684 CH_MAP_REG165 Interrupt Channel Map Register for 660 to 660+3 0x688 CH_MAP_REG166 Interrupt Channel Map Register for 664 to 664+3 154 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-29. CIC2 Registers (continued) ADDRESS OFFSET REGISTER MNEMONIC REGISTER NAME 0x68C CH_MAP_REG167 Interrupt Channel Map Register for 668 to 668+3 0x690 CH_MAP_REG168 Interrupt Channel Map Register for 672 to 672+3 0x694 CH_MAP_REG169 Interrupt Channel Map Register for 676 to 676+3 0x698 CH_MAP_REG170 Interrupt Channel Map Register for 680 to 680+3 0x69C CH_MAP_REG171 Interrupt Channel Map Register for 684 to 684+3 0x800 HINT_MAP_REG0 Host Interrupt Map Register for 0 to 0+3 0x804 HINT_MAP_REG1 Host Interrupt Map Register for 4 to 4+3 0x808 HINT_MAP_REG2 Host Interrupt Map Register for 8 to 8+3 0x80C HINT_MAP_REG3 Host Interrupt Map Register for 12 to 12+3 0x810 HINT_MAP_REG4 Host Interrupt Map Register for 16 to 16+3 0x814 HINT_MAP_REG5 Host Interrupt Map Register for 20 to 20+3 0x818 HINT_MAP_REG6 Host Interrupt Map Register for 24 to 24+3 0x81C HINT_MAP_REG7 Host Interrupt Map Register for 28 to 28+3 0x820 HINT_MAP_REG8 Host Interrupt Map Register for 32 to 32+3 0x824 HINT_MAP_REG9 Host Interrupt Map Register for 36 to 36+3 0x828 HINT_MAP_REG10 Host Interrupt Map Register for 40 to 40+3 0x82C HINT_MAP_REG11 Host Interrupt Map Register for 44 to 44+3 0x830 HINT_MAP_REG12 Host Interrupt Map Register for 48 to 48+3 0x834 HINT_MAP_REG13 Host Interrupt Map Register for 52 to 52+3 0x838 HINT_MAP_REG14 Host Interrupt Map Register for 56 to 56+3 0x83C HINT_MAP_REG15 Host Interrupt Map Register for 60 to 60+3 0x840 HINT_MAP_REG16 Host Interrupt Map Register for 63 to 63+3 0x844 HINT_MAP_REG17 Host Interrupt Map Register for 66 to 66+3 0x848 HINT_MAP_REG18 Host Interrupt Map Register for 68 to 68+3 0x84C HINT_MAP_REG19 Host Interrupt Map Register for 72 to 72+3 0x850 HINT_MAP_REG20 Host Interrupt Map Register for 76 to 76+3 0x854 HINT_MAP_REG21 Host Interrupt Map Register for 80 to 80+3 0x858 HINT_MAP_REG22 Host Interrupt Map Register for 84 to 84+3 0x85C HINT_MAP_REG23 Host Interrupt Map Register for 88 to 88+3 0x860 HINT_MAP_REG24 Host Interrupt Map Register for 92 to 92+3 0x864 HINT_MAP_REG25 Host Interrupt Map Register for 94 to 94+3 0x868 HINT_MAP_REG26 Host Interrupt Map Register for 96 to 96+3 0x86C HINT_MAP_REG27 Host Interrupt Map Register for 100 to 100+3 0x1500 ENABLE_HINT_REG0 Host Int Enable Register 0 0x1504 ENABLE_HINT_REG1 Host Int Enable Register 1 8.3.3 Inter-Processor Register Map Table 8-30. IPC Generation Registers (IPCGRx) ADDRESS START ADDRESS END SIZE REGISTER NAME DESCRIPTION 0x02620200 0x02620203 4B NMIGR0 NMI Event Generation Register for C66x CorePac0 0x02620204 0x02620207 4B NMIGR1 NMI Event Generation Register for C66x CorePac1 0x02620208 0x0262020B 4B NMIGR2 NMI Event Generation Register for C66x CorePac2 0x0262020C 0x0262020F 4B NMIGR3 NMI Event Generation Register for C66x CorePac3 0x02620210 0x02620213 4B NMIGR4 NMI Event Generation Register for C66x CorePac4 0x02620214 0x02620217 4B NMIGR5 NMI Event Generation Register for C66x CorePac5 0x02620218 0x0262021B 4B NMIGR6 NMI Event Generation Register for C66x CorePac6 Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 155 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-30. IPC Generation Registers (IPCGRx) (continued) ADDRESS START ADDRESS END SIZE REGISTER NAME DESCRIPTION 0x0262021C 0x0262021F 4B NMIGR7 NMI Event Generation Register for C66x CorePac7 0x02620220 0x0262023F 32B Reserved Reserved 0x02620240 0x02620243 4B IPCGR0 IPC Generation Register for C66x CorePac0 0x02620244 0x02620247 4B IPCGR1 IPC Generation Register for C66x CorePac1 0x02620248 0x0262024B 4B IPCGR2 IPC Generation Register for C66x CorePac2 0x0262024C 0x0262024F 4B IPCGR3 IPC Generation Register for C66x CorePac3 0x02620250 0x02620253 4B IPCGR4 IPC Generation Register for C66x CorePac4 (1) 0x02620254 0x02620257 4B IPCGR5 IPC Generation Register for C66x CorePac5 (1) 0x02620258 0x0262025B 4B IPCGR6 IPC Generation Register for C66x CorePac6 (1) 0x0262025C 0x0262025F 4B IPCGR7 IPC Generation Register for C66x CorePac7 (1) 0x02620260 0x02620263 4B IPCGR8 IPC Generation Register for ARM CorePac0 0x02620264 0x02620267 4B IPCGR9 IPC Generation Register for ARM CorePac1 0x02620268 0x0262026B 4B IPCGR10 IPC Generation Register for ARM CorePac2 (1) 0x0262026C 0x0262026F 4B IPCGR11 IPC Generation Register for ARM CorePac3 (1) 0x02620270 0x0262027B 12B Reserved Reserved 0x0262027C 0x0262027F 4B IPCGRH IPC Generation Register for Host 0x02620280 0x02620283 4B IPCAR0 IPC Acknowledgment Register for C66x CorePac0 0x02620284 0x02620287 4B IPCAR1 IPC Acknowledgment Register for C66x CorePac1 0x02620288 0x0262028B 4B IPCAR2 IPC Acknowledgment Register for C66x CorePac2 0x0262028C 0x0262028F 4B IPCAR3 IPC Acknowledgment Register for C66x CorePac3 0x02620290 0x02620293 4B IPCAR4 IPC Acknowledgment Register for C66x CorePac4 (1) 0x02620294 0x02620297 4B IPCAR5 IPC Acknowledgment Register for C66x CorePac5 (1) 0x02620298 0x0262029B 4B IPCAR6 IPC Acknowledgment Register for C66x CorePac6 (1) 0x0262029C 0x0262029F 4B IPCAR7 IPC Acknowledgment Register for C66x CorePac7 (1) 0x026202A0 0x026202A3 4B IPCAR8 IPC Acknowledgment Register for ARM CorePac0 0x026202A4 0x026202A7 4B IPCAR9 IPC Acknowledgement Register for ARM CorePac1 0x026202A8 0x026202AB 4B IPCAR10 IPC Acknowledgment Register for ARM CorePac2 (1) 0x026202AC 0x026202AF 4B IPCAR11 IPC Acknowledgment Register for ARM CorePac3 (1) 0x026202B0 0x026202BB 12B Reserved Reserved 0x026202A0 0x026202BB 28B Reserved Reserved 0x026202BC 0x026202BF 4B IPCARH IPC Acknowledgment Register for host (1) 66AK2H12/14 only. 8.3.4 NMI and LRESET The Nonmaskable Interrupts (NMI) can be generated by chip-level registers and the LRESET can be generated by software writing into LPSC registers. LRESET and NMI can also be asserted by device pins or watchdog timers. One NMI pin and one LRESET pin are shared by all eight C66x CorePacs on the device. The CORESEL[3:0] pins can be configured to select between the eight C66x CorePacs available as shown in Table 8-31. Table 8-31. LRESET and NMI Decoding CORESEL[3:0] PIN INPUT LRESET PIN INPUT NMI PIN INPUT LRESETNMIEN PIN INPUT RESET MUX BLOCK OUTPUT XXXX X X 1 No local reset or NMI assertion 0000 0 X 0 Assert local reset to C66x CorePac0 0001 0 X 0 Assert local reset to C66x CorePac1 0010 0 X 0 Assert local reset to C66x CorePac2 0011 0 X 0 Assert local reset to C66x CorePac3 156 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-31. LRESET and NMI Decoding (continued) CORESEL[3:0] PIN INPUT LRESET PIN INPUT NMI PIN INPUT LRESETNMIEN PIN INPUT RESET MUX BLOCK OUTPUT 0100 0 X 0 Assert local reset to C66x CorePac4 0101 0 X 0 Assert local reset to C66x CorePac5 0110 0 X 0 Assert local reset to C66x CorePac6 0111 0 X 0 Assert local reset to C66x CorePac7 1XXX 0 X 0 Assert local reset to all C66x CorePacs 0000 1 1 0 Deassert local reset & NMI to C66x CorePac0 0001 1 1 0 Deassert local reset & NMI to C66x CorePac1 0010 1 1 0 Deassert local reset & NMI to C66x CorePac2 0011 1 1 0 Deassert local reset & NMI to C66x CorePac3 0100 1 1 0 Deassert local reset & NMI to C66x CorePac4 (1) 0101 1 1 0 Deassert local reset & NMI to C66x CorePac5 (1) 0110 1 1 0 Deassert local reset & NMI to C66x CorePac6 (1) 0111 1 1 0 Deassert local reset & NMI to C66x CorePac7 (1) 1XXX 1 1 0 Deassert local reset & NMI to all C66x CorePacs 0000 1 0 0 Assert NMI to C66x CorePac0 0001 1 0 0 Assert NMI to C66x CorePac1 0010 1 0 0 Assert NMI to C66x CorePac2 0011 1 0 0 Assert NMI to C66x CorePac3 0100 1 0 0 Assert NMI to C66x CorePac4 (1) 0101 1 0 0 Assert NMI to C66x CorePac5 (1) 0110 1 0 0 Assert NMI to C66x CorePac6 (1) 0111 1 0 0 Assert NMI to C66x CorePac7 (1) 1XXX 1 0 0 Assert NMI to all C66x CorePacs (1) 8.4 66AK2H12/14 only. Enhanced Direct Memory Access (EDMA3) Controller for 66AK2Hxx The primary purpose of the EDMA3 is to service user-programmed data transfers between two memorymapped slave endpoints on the device. The EDMA3 services software-driven paging transfers (for example, data movement between external memory and internal memory), performs sorting or subframe extraction of various data structures, services event driven peripherals, and offloads data transfers from the device C66x DSP CorePac or the ARM CorePac. There are five EDMA channel controllers on the device: • EDMA3CC0 has two transfer controllers: TPTC0 and TPTC1 • EDMA3CC1 has four transfer controllers: TPTC0, TPTC1, TPTC2, and TPTC3 • EDMA3CC2 has four transfer controllers: TPTC0, TPTC1, TPTC2, and TPTC3 • EDMA3CC3 has two transfer controllers: TPTC0 and TPTC1 • EDMA3CC4 has two transfer controllers: TPTC0 and TPTC1 In the context of this document, TPTCx is associated with EDMA3CCy, and is referred to as EDMA3CCy TPTCx. Each of the transfer controllers has a direct connection to the switch fabric. Section 9.2 lists the peripherals that can be accessed by the transfer controllers. EDMA3CC0 is optimized to be used for transfers to/from/within the MSMC and DDR3A subsystems. The others are used for the remaining traffic. Each EDMA3 channel controller includes the following features: Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 157 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 • • • • • • • • • 8.4.1 www.ti.com Fully orthogonal transfer description – 3 transfer dimensions: • Array (multiple bytes) • Frame (multiple arrays) • Block (multiple frames) – Single event can trigger transfer of array, frame, or entire block – Independent indexes on source and destination Flexible transfer definition: – Increment or FIFO transfer addressing modes – Linking mechanism allows for ping-pong buffering, circular buffering, and repetitive/continuous transfers, all with no CPU intervention – Chaining allows multiple transfers to execute with one event 512 PaRAM entries for all EDMA3CC – Used to define transfer context for channels – Each PaRAM entry can be used as a DMA entry, QDMA entry, or link entry 64 DMA channels for all EDMA3CC – Manually triggered (CPU writes to channel controller register) – External event triggered – Chain triggered (completion of one transfer triggers another) 8 Quick DMA (QDMA) channels per EDMA3CCx – Used for software-driven transfers – Triggered upon writing to a single PaRAM set entry Two transfer controllers and two event queues with programmable system-level priority for EDMA3CC0, EDMA3CC3 and EDMA3CC4 Four transfer controllers and four event queues with programmable system-level priority for each of EDMA3CC1 and EDMA3CC2 Interrupt generation for transfer completion and error conditions Debug visibility – Queue watermarking/threshold allows detection of maximum usage of event queues – Error and status recording to facilitate debug EDMA3 Device-Specific Information The EDMA supports two addressing modes: constant addressing and increment addressing mode. Constant addressing mode is applicable to a very limited set of use cases. For most applications increment mode can be used. On the SoC, the EDMA can use constant addressing mode only with the enhanced Viterbi decoder coprocessor (VCP) and the enhanced turbo decoder coprocessor (TCP). Constant addressing mode is not supported by any other peripheral or internal memory in the SoC. Note that increment mode is supported by all peripherals. For more information on these two addressing modes, see the KeyStone Architecture Enhanced Direct Memory Access 3 (EDMA3) User's Guide. For the range of memory addresses that includes EDMA3 channel controller (EDMA3CC) control registers and EDMA3 transfer controller (TPTC) control registers, see Section Section 8.1. For memory offsets and other details on EDMA3CC and TPTC Control Register entries, see the KeyStone Architecture Enhanced Direct Memory Access 3 (EDMA3) User's Guide. 8.4.2 EDMA3 Channel Controller Configuration Table 8-32 shows the configuration for each of the EDMA3 channel controllers present on the device. 158 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-32. EDMA3 Channel Controller Configuration DESCRIPTION EDMA3 CC0 EDMA3 CC1 EDMA3 CC2 EDMA3 CC3 EDMA3 CC4 Number of DMA channels in channel controller 64 64 64 64 64 Number of QDMA channels 8 8 8 8 8 Number of interrupt channels 64 64 64 64 64 Number of PaRAM set entries 512 512 512 512 512 Number of event queues 2 4 4 2 2 Number of transfer controllers 2 4 4 2 2 Memory protection existence Yes Yes Yes Yes Yes Number of memory protection and shadow regions 8 8 8 8 8 8.4.3 EDMA3 Transfer Controller Configuration Each transfer controller on the device is designed differently based on considerations like performance requirements, system topology (like main TeraNet bus width, external memory bus width), and so forth. The parameters that determine the transfer controller configurations are: • FIFOSIZE: Determines the size in bytes for the data FIFO that is the temporary buffer for the in-flight data. The data FIFO is where the read return data read by the TC read controller from the source endpoint is stored and subsequently written out to the destination endpoint by the TC write controller. • BUSWIDTH: The width of the read and write data buses in bytes, for the TC read and write controller, respectively. This is typically equal to the bus width of the main TeraNet interface. • Default Burst Size (DBS): The DBS is the maximum number of bytes per read/write command issued by a transfer controller. • DSTREGDEPTH: This determines the number of destination FIFO register sets. The number of destination FIFO register sets for a transfer controller determines the maximum number of outstanding transfer requests. All four parameters listed above are fixed by the design of the device. Table 8-33 shows the configuration of each of the EDMA3 transfer controllers present on the device. Table 8-33. EDMA3 Transfer Controller Configuration EDMA3 CC0/CC4 EDMA3 CC1 EDMA3 CC2 EDMA3CC3 PARAMETER TC0 TC1 TC0 TC1 TC2 TC3 TC0 TC1 TC2 TC3 TC0 TC1 FIFOSIZE 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes 1024 bytes BUSWIDTH 32 bytes 32 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes 16 bytes DSTREGDEPTH 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries 4 entries DBS 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 128 bytes 64 bytes 64 bytes 8.4.4 EDMA3 Channel Synchronization Events The EDMA3 supports up to 64 DMA channels for all EDMA3CC that can be used to service system peripherals and to move data between system memories. DMA channels can be triggered by synchronization events generated by system peripherals. The following tables list the source of the synchronization event associated with each of the EDMA3CC DMA channels. On the 66AK2Hxx, the association of each synchronization event and DMA channel is fixed and cannot be reprogrammed. For more detailed information on the EDMA3 module and how EDMA3 events are enabled, captured, processed, prioritized, linked, chained, and cleared, and so forth, see the KeyStone Architecture Enhanced Direct Memory Access 3 (EDMA3) User's Guide. Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 159 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-34. EDMA3CC0 Events for 66AK2Hxx EVENT NO. EVENT NAME DESCRIPTION 0 TIMER_8_INTL Timer interrupt low 1 TIMER_8_INTH Timer interrupt high 2 TIMER_9_INTL Timer interrupt low 3 TIMER_9_INTH Timer interrupt high 4 TIMER_10_INTL Timer interrupt low 5 TIMER_10_INTH Timer interrupt high 6 TIMER_11_INTL Timer interrupt low 7 TIMER_11_INTH Timer interrupt high 8 CIC_2_OUT66 CIC2 Interrupt Controller output 9 CIC_2_OUT67 CIC2 Interrupt Controller output 10 CIC_2_OUT68 CIC2 Interrupt Controller output 11 CIC_2_OUT69 CIC2 Interrupt Controller output 12 CIC_2_OUT70 CIC2 Interrupt Controller output 13 CIC_2_OUT71 CIC2 Interrupt Controller output 14 CIC_2_OUT72 CIC2 Interrupt Controller output 15 CIC_2_OUT73 CIC2 Interrupt Controller output 16 GPIO_INT8 GPIO interrupt 17 GPIO_INT9 GPIO interrupt 18 GPIO_INT10 GPIO interrupt 19 GPIO_INT11 GPIO interrupt 20 GPIO_INT12 GPIO interrupt 21 GPIO_INT13 GPIO interrupt 22 GPIO_INT14 GPIO interrupt 23 GPIO_INT15 GPIO interrupt 24 TIMER_4_INTL Timer interrupt low (1) 25 TIMER_4_INTH Timer interrupt high (1) 26 TIMER_5_INTL Timer interrupt low (1) 27 TIMER_5_INTH Timer interrupt high (1) 28 TIMER_6_INTL Timer interrupt low (1) 29 TIMER_6_INTH Timer interrupt high (1) 30 TIMER_7_INTL Timer interrupt low (1) 31 TIMER_7_INTH Timer interrupt high (1) 32 GPIO_INT0 GPIO interrupt 33 GPIO_INT1 GPIO interrupt 34 GPIO_INT2 GPIO interrupt 35 GPIO_INT3 GPIO interrupt 36 GPIO_INT4 GPIO interrupt 37 GPIO_INT5 GPIO interrupt 38 GPIO_INT6 GPIO interrupt 39 GPIO_INT7 GPIO interrupt 40 TIMER_0_INTL Timer interrupt low 41 TIMER_0_INTH Timer interrupt high 42 TIMER_1_INTL Timer interrupt low 43 TIMER_1_INTH Timer interrupt high 44 TIMER_2_INTL Timer interrupt low 45 TIMER_2_INTH Timer interrupt high (1) 160 66AK2H14 only. Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-34. EDMA3CC0 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 46 TIMER_3_INTL Timer interrupt low 47 TIMER_3_INTH Timer interrupt high 48 SRIO_INTDST0 SRIO interrupt 49 SRIO_INTDST1 SRIO interrupt 50 SRIO_INTDST2 SRIO interrupt 51 SRIO_INTDST3 SRIO interrupt 52 SRIO_INTDST4 SRIO interrupt 53 SRIO_INTDST5 SRIO interrupt 54 SRIO_INTDST6 SRIO interrupt 55 SRIO_INTDST7 SRIO interrupt 56 Reserved Reserved 57 Reserved Reserved 58 Reserved Reserved 59 Reserved Reserved 60 Reserved Reserved 61 Reserved Reserved 62 Reserved Reserved 63 Reserved Reserved Table 8-35. EDMA3CC1 Events for 66AK2Hxx EVENT NO. EVENT NAME DESCRIPTION 0 SPI_0_INT0 SPI0 interrupt 1 SPI_0_INT1 SPI0 interrupt 2 SPI_0_XEVT SPI0 transmit event 3 SPI_0_REVT SPI0 receive event 4 SEM_INT8 Semaphore interrupt 5 SEM_INT9 Semaphore interrupt 6 GPIO_INT0 GPIO interrupt 7 GPIO_INT1 GPIO interrupt 8 GPIO_INT2 GPIO interrupt 9 GPIO_INT3 GPIO interrupt 10 Reserved Reserved 11 Reserved Reserved 12 Reserved Reserved 13 Reserved Reserved 14 SEM_INT0 Semaphore interrupt 15 SEM_INT1 Semaphore interrupt 16 SEM_INT2 Semaphore interrupt 17 SEM_INT3 Semaphore interrupt 18 SEM_INT4 Semaphore interrupt 19 SEM_INT5 Semaphore interrupt 20 SEM_INT6 Semaphore interrupt 21 SEM_INT7 Semaphore interrupt 22 TIMER_8_INTL Timer interrupt low 23 TIMER_8_INTH Timer interrupt high 24 TIMER_9_INTL Timer interrupt low Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 161 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-35. EDMA3CC1 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 25 TIMER_9_INTH Timer interrupt high 26 TIMER_10_INTL Timer interrupt low 27 TIMER_10_INTH Timer interrupt high 28 TIMER_11_INTL Timer interrupt low 29 TIMER_11_INTH Timer interrupt high 30 TIMER_12_INTL Timer interrupt low 31 TIMER_12_INTH Timer interrupt high 32 TIMER_13_INTL Timer interrupt low 33 TIMER_13_INTH Timer interrupt high 34 TIMER_14_INTL Timer interrupt low 35 TIMER_14_INTH Timer interrupt high 36 TIMER_15_INTL Timer interrupt low 37 TIMER_15_INTH Timer interrupt high 38 SEM_INT10 Semaphore interrupt 39 SEM_INT11 Semaphore interrupt 40 SEM_INT12 Semaphore interrupt 41 SEM_INT13 Semaphore interrupt 42 CIC_2_OUT0 CIC2 Interrupt Controller output 43 CIC_2_OUT1 CIC2 Interrupt Controller output 44 CIC_2_OUT2 CIC2 Interrupt Controller output 45 CIC_2_OUT3 CIC2 Interrupt Controller output 46 CIC_2_OUT4 CIC2 Interrupt Controller output 47 CIC_2_OUT5 CIC2 Interrupt Controller output 48 CIC_2_OUT6 CIC2 Interrupt Controller output 49 CIC_2_OUT7 CIC2 Interrupt Controller output 50 CIC_2_OUT8 CIC2 Interrupt Controller output 51 Reserved Reserved 52 Reserved Reserved 53 I2C_0_REVT I2C0 receive 54 I2C_0_XEVT I2C0 transmit 55 CIC_2_OUT13 CIC2 Interrupt Controller output 56 CIC_2_OUT14 CIC2 Interrupt Controller output 57 CIC_2_OUT15 CIC2 Interrupt Controller output 58 CIC_2_OUT16 CIC2 Interrupt Controller output 59 CIC_2_OUT17 CIC2 Interrupt Controller output 60 CIC_2_OUT18 CIC2 Interrupt Controller output 61 CIC_2_OUT19 CIC2 Interrupt Controller output 62 Reserved Reserved 63 Reserved Reserved Table 8-36. EDMA3CC2 Events for 66AK2Hxx EVENT NO. EVENT NAME DESCRIPTION 0 Reserved Reserved 1 Reserved Reserved 2 Reserved Reserved 3 Reserved Reserved 162 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-36. EDMA3CC2 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 4 Reserved Reserved 5 Reserved Reserved 6 TETB_FULLINT4 TETB4 is full 7 TETB_HFULLINT4 TETB4 is half full 8 TETB_FULLINT5 TETB5 is full 9 TETB_HFULLINT5 TETB5 is half full 10 TETB_FULLINT6 TETB6 is full 11 TETB_HFULLINT6 TETB6 is half full 12 TETB_FULLINT7 TETB7 is full 13 TETB_HFULLINT7 TETB7 is half full 14 SRIO_INTDST0 SRIO interrupt 15 SRIO_INTDST1 SRIO interrupt 16 SRIO_INTDST2 SRIO interrupt 17 SRIO_INTDST3 SRIO interrupt 18 SRIO_INTDST4 SRIO interrupt 19 SRIO_INTDST5 SRIO interrupt 20 SRIO_INTDST6 SRIO interrupt 21 SRIO_INTDST7 SRIO interrupt 22 Reserved Reserved 23 Reserved Reserved 24 Reserved Reserved 25 Reserved Reserved 26 GPIO_INT0 GPIO interrupt 27 GPIO_INT1 GPIO interrupt 28 GPIO_INT2 GPIO interrupt 29 GPIO_INT3 GPIO interrupt 30 GPIO_INT4 GPIO interrupt 31 GPIO_INT5 GPIO interrupt 32 GPIO_INT6 GPIO interrupt 33 GPIO_INT7 GPIO interrupt 34 Reserved Reserved 35 Reserved Reserved 36 Reserved Reserved 37 Reserved Reserved 38 CIC_2_OUT48 CIC2 Interrupt Controller output 39 Reserved Reserved 40 UART_0_URXEVT UART0 receive event 41 UART_0_UTXEVT UART0 transmit event 42 CIC_2_OUT22 CIC2 Interrupt Controller output 43 CIC_2_OUT23 CIC2 Interrupt Controller output 44 CIC_2_OUT24 CIC2 Interrupt Controller output 45 CIC_2_OUT25 CIC2 Interrupt Controller output 46 CIC_2_OUT26 CIC2 Interrupt Controller output 47 CIC_2_OUT27 CIC2 Interrupt Controller output 48 CIC_2_OUT28 CIC2 Interrupt Controller output 49 SPI_0_XEVT SPI0 transmit event 50 SPI_0_REVT SPI0 receive event Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 163 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-36. EDMA3CC2 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 51 Reserved Reserved 52 Reserved Reserved 53 Reserved Reserved 54 Reserved Reserved 55 Reserved Reserved 56 Reserved Reserved 57 Reserved Reserved 58 Reserved Reserved 59 Reserved Reserved 60 Reserved Reserved 61 Reserved Reserved 62 Reserved Reserved 63 Reserved Reserved Table 8-37. EDMA3CC3 Events for 66AK2Hxx EVENT NO. EVENT NAME DESCRIPTION 0 SPI_2_INT0 SPI2 interrupt 1 SPI_2_INT1 SPI2 interrupt 2 SPI_2_XEVT SPI2 transmit event 3 SPI_2_REVT SPI2 receive event 4 I2C_2_REVT I2C2 receive 5 I2C_2_XEVT I2C2 transmit 6 UART_1_URXEVT UART1 receive event 7 UART_1_UTXEVT UART1 transmit event 8 SPI_1_INT0 SPI1 interrupt 9 SPI_1_INT1 SPI1 interrupt 10 SPI_1_XEVT SPI1 transmit event 11 SPI_1_REVT SPI1 receive event 12 I2C_0_REVT I2C0 receive 13 I2C_0_XEVT I2C0 transmit 14 I2C_1_REVT I2C1 receive 15 I2C_1_XEVT I2C1 transmit 16 SRIO_INTDST0 SRIO interrupt 17 SRIO_INTDST1 SRIO interrupt 18 SRIO_INTDST2 SRIO interrupt 19 SRIO_INTDST3 SRIO interrupt 20 SRIO_INTDST4 SRIO interrupt 21 SRIO_INTDST5 SRIO interrupt 22 SRIO_INTDST6 SRIO interrupt 23 SRIO_INTDST7 SRIO interrupt 24 Reserved Reserved 25 Reserved Reserved 26 Reserved Reserved 27 Reserved Reserved 28 Reserved Reserved 29 Reserved Reserved 164 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-37. EDMA3CC3 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 30 Reserved Reserved 31 Reserved Reserved 32 TETB_FULLINT0 TETB0 is full 33 TETB_HFULLINT0 TETB0 is half full 34 TETB_FULLINT1 TETB1 is full 35 TETB_HFULLINT1 TETB1 is half full 36 TETB_FULLINT2 TETB2 is full 37 TETB_HFULLINT2 TETB2 is half full 38 TETB_FULLINT3 TETB3 is full 39 TETB_HFULLINT3 TETB3 is half full 40 Reserved Reserved 41 Reserved Reserved 42 Reserved Reserved 43 Reserved Reserved 44 Reserved Reserved 45 Reserved Reserved 46 Reserved Reserved 47 Reserved Reserved 48 Reserved Reserved 49 Reserved Reserved 50 Reserved Reserved 51 Reserved Reserved 52 Reserved Reserved 53 Reserved Reserved 54 Reserved Reserved 55 Reserved Reserved 56 CIC_2_OUT57 CIC2 Interrupt Controller output 57 CIC_2_OUT50 CIC2 Interrupt Controller output 58 CIC_2_OUT51 CIC2 Interrupt Controller output 59 CIC_2_OUT52 CIC2 Interrupt Controller output 60 CIC_2_OUT53 CIC2 Interrupt Controller output 61 CIC_2_OUT54 CIC2 Interrupt Controller output 62 CIC_2_OUT55 CIC2 Interrupt Controller output 63 CIC_2_OUT56 CIC2 Interrupt Controller output Table 8-38. EDMA3CC4 Events for 66AK2Hxx EVENT NO. EVENT NAME DESCRIPTION 0 GPIO_INT16 GPIO interrupt 1 GPIO_INT17 GPIO interrupt 2 GPIO_INT18 GPIO interrupt 3 GPIO_INT19 GPIO interrupt 4 GPIO_INT20 GPIO interrupt 5 GPIO_INT21 GPIO interrupt 6 GPIO_INT22 GPIO interrupt 7 GPIO_INT23 GPIO interrupt 8 Reserved Reserved Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 165 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 8-38. EDMA3CC4 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 9 Reserved Reserved 10 Reserved Reserved 11 Reserved Reserved 12 Reserved Reserved 13 Reserved Reserved 14 Reserved Reserved 15 Reserved Reserved 16 Reserved Reserved 17 Reserved Reserved 18 Reserved Reserved 19 Reserved Reserved 20 Reserved Reserved 21 Reserved Reserved 22 Reserved Reserved 23 Reserved Reserved 24 TIMER_8_INTL Timer interrupt low 25 TIMER_8_INTH Timer interrupt high 26 TIMER_14_INTL Timer interrupt low 27 TIMER_14_INTH Timer interrupt high 28 TIMER_15_INTL Timer interrupt low 29 TIMER_15_INTH Timer interrupt high 30 DBGTBR_DMAINT Debug trace buffer (TBR) DMA event 31 ARM_TBR_DMA ARM trace buffer (TBR) DMA event 32 QMSS_QUE_PEND_658 Navigator transmit queue pending event for indicated queue 33 QMSS_QUE_PEND_659 Navigator transmit queue pending event for indicated queue 34 QMSS_QUE_PEND_660 Navigator transmit queue pending event for indicated queue 35 QMSS_QUE_PEND_661 Navigator transmit queue pending event for indicated queue 36 QMSS_QUE_PEND_662 Navigator transmit queue pending event for indicated queue 37 QMSS_QUE_PEND_663 Navigator transmit queue pending event for indicated queue 38 QMSS_QUE_PEND_664 Navigator transmit queue pending event for indicated queue 39 QMSS_QUE_PEND_665 Navigator transmit queue pending event for indicated queue 40 QMSS_QUE_PEND_8736 Navigator transmit queue pending event for indicated queue 41 QMSS_QUE_PEND_8737 Navigator transmit queue pending event for indicated queue 42 QMSS_QUE_PEND_8738 Navigator transmit queue pending event for indicated queue 43 QMSS_QUE_PEND_8739 Navigator transmit queue pending event for indicated queue 44 QMSS_QUE_PEND_8740 Navigator transmit queue pending event for indicated queue 45 QMSS_QUE_PEND_8741 Navigator transmit queue pending event for indicated queue 46 QMSS_QUE_PEND_8742 Navigator transmit queue pending event for indicated queue 47 QMSS_QUE_PEND_8743 Navigator transmit queue pending event for indicated queue 48 ARM_NCNTVIRQ3 ARM virtual timer interrupt for core 3 49 ARM_NCNTVIRQ2 ARM virtual timer interrupt for core 2 50 ARM_NCNTVIRQ1 ARM virtual timer interrupt for core 1 51 ARM_NCNTVIRQ0 ARM virtual timer interrupt for core 0 52 ARM_NCNTPNSIRQ3 ARM non secure timer interrupt for core 3 53 ARM_NCNTPNSIRQ2 ARM non secure timer interrupt for core 2 54 ARM_NCNTPNSIRQ1 ARM non secure timer interrupt for core 1 55 ARM_NCNTPNSIRQ0 ARM non secure timer interrupt for core 0 166 Memory, Interrupts, and EDMA for 66AK2Hxx Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 8-38. EDMA3CC4 Events for 66AK2Hxx (continued) EVENT NO. EVENT NAME DESCRIPTION 56 CIC_2_OUT82 CIC2 Interrupt Controller output 57 CIC_2_OUT83 CIC2 Interrupt Controller output 58 CIC_2_OUT84 CIC2 Interrupt Controller output 59 CIC_2_OUT85 CIC2 Interrupt Controller output 60 CIC_2_OUT86 CIC2 Interrupt Controller output 61 CIC_2_OUT87 CIC2 Interrupt Controller output 62 CIC_2_OUT88 CIC2 Interrupt Controller output 63 CIC_2_OUT89 CIC2 Interrupt Controller output Memory, Interrupts, and EDMA for 66AK2Hxx Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 167 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 9 System Interconnect On the KeyStone II devices, the C66x CorePac, the EDMA3 transfer controllers and the system peripherals are interconnected through the TeraNets, which are nonblocking switch fabrics enabling fast and contention-free internal data movement. The TeraNets provide low-latency, concurrent data transfers between master peripherals and slave peripherals. The TeraNets also allow for seamless arbitration between the system masters when accessing system slaves. The ARM CorePac is connected to the MSMC and the debug subsystem directly, and to other masters via the TeraNets. Through the MSMC, the ARM CorePacs can be interconnected to DDR3A and TeraNet 3_A, which allows the ARM CorePacs to access to the peripheral buses: • TeraNet 3P_A for peripheral configuration • TeraNet 6P_A for ARM • Boot ROM • TeraNet 3_C for DDR3B 9.1 Internal Buses and Switch Fabrics The C66x CorePacs, the ARM CorePacs, the EDMA3 traffic controllers, and the various system peripherals can be classified into two categories: masters and slaves. • Masters are capable of initiating read and write transfers in the system and do not rely on the EDMA3 for their data transfers. • Slaves on the other hand rely on the masters to perform transfers to and from them. Examples of masters include the EDMA3 traffic controllers and network coprocessor packet DMA. Examples of slaves include the SPI, UART, and I2C. The masters and slaves in the device communicate through the TeraNet (switch fabric). The device contains two types of switch fabric: • Data TeraNet is a high-throughput interconnect mainly used to move data across the system • Configuration TeraNet is mainly used to access peripheral registers Some peripherals have both a data bus and a configuration bus interface, while others only have one type of interface. Furthermore, the bus interface width and speed varies from peripheral to peripheral. Note that the data TeraNet also connects to the configuration TeraNet. 9.2 Switch Fabric Connections Matrix - Data Space Figure 9-1, Figure 9-2, Figure 9-3, and Figure 9-4 show the connections between masters and slaves through various sections of the TeraNet. 168 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Bridge_11 Bridge_1 66AK2H Tracer_SPI_ ROM_EMIF16 Bridge_2 From TeraNet_3_C TNet_6P_A CPU/6 TeraNet 3_A-1 CPU/3 Bridge_3 SRIO Packet DMA M QM Packet DMA M QM_2 Packet DMA M Debug_SS M TNet_3_D CPU/3 M TNet_3_G CPU/3 MPU_8 S EMIF16 MPU_12 S SPI_0 MPU_13 S SPI_1 MPU_14 S SPI_2 S Boot_ROM S Boot_ROM ARM Bridge_5 Bridge_6 Bridge_7 To TeraNet_3_C Bridge_8 Bridge_9 Bridge_10 Bridge_12 To TeraNet_3P_A Bridge_13 USB_MST Bridge_14 Figure 9-1. TeraNet 3_A-1 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 169 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com MPU_1 66AK2H Tracer_QM_M S QM_SS Tracer_SPI_ ROM_EMIF16 NETCP TC_0 EDMA CC1 TC_1 TC_2 TC_3 TC_0 EDMA CC2 TC_1 TC_2 TC_3 EDMA CC3 M M M M M M M M M M TC_1 M M SRIO_M M PCIe M TC_0 PCIe L2 Cache_0_A L2 Cache_0_B L2 Cache_1_A L2 Cache_1_B TNet_3_L CPU/3 TeraNet 3_A-2 10GbE (66AK2H14 only) CPU/3 S L2 Cache_2_A L2 Cache_2_B L2 Cache_3_A L2 Cache_3_B To TeraNet C66x SDMA L2 Cache_4_A L2 Cache_4_B L2 Cache_5_A L2 Cache_5_B L2 Cache_6_A L2 Cache_6_B L2 Cache_7_A L2 Cache_7_B Figure 9-2. TeraNet 3_A-2 170 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com XMC SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 66AK2H ´8 HyperLink 0 M HyperLink 1 M TeraNet 3_B CPU/3 ARM CorePac S SES S SMS S HyperLink 0 S HyperLink 1 S Tracer_ MSMC0-8 MSMC M M DDR3A BR_SES_0 CPU/3 Bridge_5 Bridge_6 Bridge_7 From TeraNet_3_A Bridge_8 Bridge_9 BR_SES_1 TNet_SES CPU/1 BR_SES_2 BR_SMS_0 BR_SMS_1 TNet_SMS CPU/1 BR_SMS_2 QM_Second M EDMA CC0 TC_0 TC_1 M M EDMA CC4 TC_0 M M TC_1 TeraNet 3_C Bridge_10 TNet_msmc_sys CPU/1 To TeraNet_3_A To TeraNet_3P_A CPU Port TNet_3_U CPU/3 Sys Port MPU_7 DDR3B Tracer_DDRB Bridge_1 To TeraNet_3_A Bridge_2 Bridge_3 Figure 9-3. TeraNet 3_C Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 171 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 66AK2H L2 Cache_0_A L2 Cache_0_B L2 Cache_1_A L2 Cache_1_B L2 Cache_2_A L2 Cache_2_B L2 Cache_3_A L2 Cache_3_B TNet_3_M CPU/3 Tracer_L2_0 TNet_3_N CPU/3 Tracer_L2_1 TNet_3_O CPU/3 Tracer_L2_2 TNet_3_P CPU/3 Tracer_L2_3 TNet_3_Q CPU/3 Tracer_L2_4 TNet_3_R CPU/3 Tracer_L2_5 TNet_3_S CPU/3 Tracer_L2_6 TNet_3_T CPU/3 Tracer_L2_7 S CorePac_0 S CorePac_1 S CorePac_2 S CorePac_3 S CorePac_4 S CorePac_5 S CorePac_6 S CorePac_7 From TeraNet 3_A-2 L2 Cache_4_A L2 Cache_4_B L2 Cache_5_A L2 Cache_5_B L2 Cache_6_A L2 Cache_6_B L2 Cache_7_A L2 Cache_7_B Figure 9-4. TeraNet C66x to SDMA 172 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 9-1 lists the master and slave end-point connections. Intersecting cells may contain one of the following: • Y — There is a connection between this master and that slave. • - — There is no connection between this master and that slave. • n — A numeric value indicates that the path between this master and that slave goes through bridge n. Table 9-1. Data Space Interconnect MASTERS AEMIF16 BOOTROM_ARM BOOTROM_C66X COREPAC0_SDMA COREPAC1_SDMA COREPAC2_SDMA COREPAC3_SDMA COREPAC4_SDMA COREPAC5_SDMA COREPAC6_SDMA COREPAC7_SDMA DBG_STM DDR3B HYPERLINK0 HYPERLINK1 MSMC_SES MSMC_SMS PCIE QM SPI(0-2) SLAVES 10GbE (1) - - - Y Y Y Y Y Y Y Y - 10 - - ses_2 sms_2 Y Y - CorePac0_CFG - - - - - - - - - - - - - - - - - - - - CorePac1_CFG - - - - - - - - - - - - - - - - - - - - CorePac2_CFG - - - - - - - - - - - - - - - - - - - - CorePac3_CFG - - - - - - - - - - - - - - - - - - - - CorePac4_CFG - - - - - - - - - - - - - - - - - - - - CorePac5_CFG - - - - - - - - - - - - - - - - - - - - CorePac6_CFG - - - - - - - - - - - - - - - - - - - - CorePac7_CFG - - - - - - - - - - - - - - - - - - - - CPT_CFG - - - - - - - - - - - Y - - - - - - - - CPT_DDR3A - - - - - - - - - - - Y - - - - - - - - CPT_DDR3B - - - - - - - - - - - Y - - - - - - - - CPT_INTC - - - - - - - - - - - Y - - - - - - - - CPT_L2_(0-7) - - - - - - - - - - - Y - - - - - - - - CPT_MSMC(0-7) - - - - - - - - - - - Y - - - - - - - - CPT_QM_CFG1 - - - - - - - - - - - Y - - - - - - - - CPT_QM_CFG2 - - - - - - - - - - - Y - - - - - - - - CPT_QM_M - - - - - - - - - - - Y - - - - - - - - CPT_SPI_ROM_EMIF16 - - - - - - - - - - - Y - - - - - - - - CPT_TPCC(0_4)T - - - - - - - - - - - Y - - - - - - - - CPT_TPCC(1_2_3)T - - - - - - - - - - - Y - - - - - - - - DBG_DAP Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y EDMA0_CC_TR - - - - - - - - - - - - - - - - - - - - EDMA0_TC0_RD 2,11 2,11 2,11 Y Y Y Y Y Y Y Y - Y Y Y SES_0 SMS_0 Y Y 2,11 EDMA0_TC0_WR 2,11 - - Y Y Y Y Y Y Y Y - Y Y Y SES_0 SMS_0 Y Y 2,11 EDMA0_TC1_RD 3,11 3,11 3,11 Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y - 3,11 EDMA0_TC1_WR 3,11 - - Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y - 3,11 EDMA1_CC_TR - - - - - - - - - - - - - - - - - - - - EDMA1_TC0_RD 11 11 11 Y Y Y Y Y Y Y Y - 5 Y Y SES_0 SMS_0 Y Y 11 EDMA1_TC0_WR 11 - - Y Y Y Y Y Y Y Y Y 5 Y Y SES_0 SMS_0 Y Y 11 EDMA1_TC1_RD 11 Y Y Y Y Y Y Y Y Y Y - 6 Y Y SES_1 SMS_1 Y Y 11 EDMA1_TC1_WR 11 - - Y Y Y Y Y Y Y Y - 6 Y Y SES_1 SMS_1 Y Y 11 EDMA1_TC2_RD 11 Y Y Y Y Y Y Y Y Y Y - 7 Y Y SES_1 SMS_1 Y - 11 EDMA1_TC2_WR 11 - - Y Y Y Y Y Y Y Y - 7 Y Y SES_1 SMS_1 Y - 11 EDMA1_TC3_RD 11 Y Y Y Y Y Y Y Y Y Y - 8 Y Y SES_1 SMS_1 Y - 11 EDMA1_TC3_WR 11 - - Y Y Y Y Y Y Y Y Y 8 Y Y SES_1 SMS_1 Y - 11 - - - - - - - - - - - - - - - - - - - - EDMA2_CC_TR (1) 66AK2H14 only. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 173 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 9-1. Data Space Interconnect (continued) MASTERS AEMIF16 BOOTROM_ARM BOOTROM_C66X COREPAC0_SDMA COREPAC1_SDMA COREPAC2_SDMA COREPAC3_SDMA COREPAC4_SDMA COREPAC5_SDMA COREPAC6_SDMA COREPAC7_SDMA DBG_STM DDR3B HYPERLINK0 HYPERLINK1 MSMC_SES MSMC_SMS PCIE QM SPI(0-2) SLAVES EDMA2_TC0_RD 11 Y Y Y Y Y Y Y Y Y Y - 9 Y Y SES_2 SMS_2 Y Y 11 EDMA2_TC0_WR 11 - - Y Y Y Y Y Y Y Y Y 9 Y Y SES_2 SMS_2 Y Y 11 EDMA2_TC1_RD 11 Y Y Y Y Y Y Y Y Y Y - 10 Y Y SES_2 SMS_2 Y Y 11 EDMA2_TC1_WR 11 - - Y Y Y Y Y Y Y Y - 10 Y Y SES_2 SMS_2 Y Y 11 EDMA2_TC2_RD 11 Y Y Y Y Y Y Y Y Y Y - 5 Y Y SES_0 SMS_0 Y - 11 EDMA2_TC2_WR 11 - - Y Y Y Y Y Y Y Y Y 5 Y Y SES_0 SMS_0 Y - 11 EDMA2_TC3_RD 11 Y Y Y Y Y Y Y Y Y Y - 6 Y Y SES_0 SMS_0 Y - 11 EDMA2_TC3_WR 11 - - Y Y Y Y Y Y Y Y - 6 Y Y SES_0 SMS_0 Y - 11 EDMA3_CC_TR - - - - - - - - - - - - - - - - - - - - EDMA3_TC0_RD 11 Y Y Y Y Y Y Y Y Y Y - 7 Y Y SES_1 SMS_1 Y Y 11 EDMA3_TC0_WR 11 - - Y Y Y Y Y Y Y Y Y 7 Y Y SES_1 SMS_1 Y Y 11 EDMA3_TC1_RD 11 Y Y Y Y Y Y Y Y Y Y - 8 Y Y SES_1 SMS_1 Y - 11 EDMA3_TC1_WR 11 - - Y Y Y Y Y Y Y Y - 8 Y Y SES_1 SMS_1 Y - 11 EDMA4_CC_TR - - - - - - - - - - - - - - - - - - - - EDMA4_TC0_RD 2,11 2,11 2,11 Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y Y 2,11 EDMA4_TC0_WR 2,11 - - Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y Y 2,11 EDMA4_TC1_RD 3,11 3,11 3,11 Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y - 3,11 EDMA4_TC1_WR 3,11 - - Y Y Y Y Y Y Y Y - Y Y Y SES_1 SMS_1 Y - 3,11 HyperLink0_Master 11 1,11 1,11 Y Y Y Y Y Y Y Y - Y - - Y Y Y Y Y HyperLink1_Master 11 1,11 1,11 Y Y Y Y Y Y Y Y - Y - - Y Y Y Y Y MSMC_SYS 11 11 11 Y Y Y Y Y Y Y Y Y Y Y Y - - Y Y 11 NETCP - - - Y Y Y Y Y Y Y Y - 7 - - SES_1 SMS_1 Y Y - 11 - - Y Y Y Y Y Y Y Y Y 10 10 10 SES_2 SMS_2 - Y 11 QM_Master1 - - - Y Y Y Y Y Y Y Y - 5 Y Y SES_0 SMS_0 - Y - QM_Master2 - - - Y Y Y Y Y Y Y Y - 8 Y Y SES_1 SMS_1 - Y - QM_SEC - - - Y Y Y Y Y Y Y Y Y Y Y Y SES_2 SMS_2 - - - SRIO 11 - - Y Y Y Y Y Y Y Y Y 9 Y Y SES_2 SMS_2 - Y 11 SRIO Packet DMA 11 - - Y Y Y Y Y Y Y Y - 9 - - SES_2 SMS_2 - Y - - - - Y Y Y Y Y Y Y Y Y 5 Y Y SES_0 SMS_0 - Y - PCIE USB 174 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 9.3 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 TeraNet Switch Fabric Connections Matrix - Configuration Space Figure 9-5, Figure 9-6, Figure 9-7, and Figure 9-8 show the connections between masters and slaves through various sections of the TeraNet. S MPU (´ 15) MPU_2 M QM_SS_ CFG1 MPU_6 M QM_SS_ CFG2 MPU_10 S Semaphore S S CC0 TC (´ 2) S S CC4 TC (´ 2) S S CC1 TC (´ 4) S S CC2 TC (´ 4) S S CC3 TC (´ 2) S ARM INTC S CP_INTC0-2 Bridge_12 Bridge_13 From TeraNet_3_A Tracer_QM_CFG1 Bridge_14 Tracer_QM_CFG2 From TeraNet_3_C M CorePac_1 M CorePac_2 M CorePac_3 M CorePac_4 M CorePac_5 M CorePac_6 M CorePac_7 M TeraNet 3P_A CorePac_0 CPU/3 Tracer_SM Tracer _EDMA CC0 & CC4 Tracer _EDMA CC1 - CC3 MPU_9 TNet_3P_M CPU/3 TNet_3P_C CPU/3 TNet_3P_L CPU/3 Tracer_INTC TETB CorePac (´ 8) DBG_TBR_SYS (Debug_SS) TBR_SYS_ ARM_CorePac MPU_0 To TeraNet_3P_B Tracer_CFG To TeraNet_3P_Tracer 66AK2H Figure 9-5. TeraNet 3P_A Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 175 66AK2H14, 66AK2H12, 66AK2H06 From TeraNet_3P_A www.ti.com TeraNet 3P_B CPU/3 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 TNet_3P_N CPU/3 S CP_T0-T8 (MSMC) TNet_3P_D CPU/3 S CP_T (´ 23) S SRIO S NetCP S 10GbE (66AK2H14 only) MPU_11 Bridge 20 To TeraNet_6P_B 66AK2H Figure 9-6. TeraNet 3P_B Bridge 20 TeraNet 6P_B CPU/6 From TeraNet_3P_B 66AK2H S Timer (´ 20) S OTP S Debug SS S PLL_CTL S GPSC S BOOT_CFG S UART (´ 2) S I C (´ 3) S GPIO 2 S USB PHY CFG S PCIe SerDes CFG S HyperLink SerDes CFG S SRIO SerDes CFG S NetCP SerDes CFG S DDR3B PHY CFG S DDR3A PHY CFG S USB MMR CFG S SmartReflex0 S SmartReflex1 Figure 9-7. TeraNet 6P_B 176 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 M Tracer_MSMC_1 M Tracer_MSMC_2 M Tracer_MSMC_3 M Tracer_MSMC_4 M Tracer_MSMC_5 M Tracer_MSMC_6 M Tracer_MSMC_7 M Tracer_MSMC_8 M TeraNet 3P_Tracer CPU/3 Tracer_MSMC_0 From TeraNet_3P_A Tracer_SM M Tracer_CIC M Tracer_DDRB M Tracer_QM_CFG1 M Tracer_QM_CFG2 M Tracer_QM_M M Tracer_L2_0-7 (´ 8) M Tracer_CFG M Tracer_EDMA3CC0_4 M Tracer_EDMA3CC1_2_3 M Tracer_SPI_ ROM_EMIF16 66AK2H TeraNet 3P_P CPU/3 www.ti.com M S Debug_SS STM Figure 9-8. TeraNet 3P_Tracer Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 177 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 9-2 and Table 9-3 list the master and slave end-point connections. Intersecting cells may contain one of the following: • Y — There is a connection between this master and that slave. • - — There is no connection between this master and that slave. • n — A numeric value indicates that the path between this master and that slave goes through bridge n. Table 9-2. Configuration Space Interconnect - Section 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA4_CC_CFG EDMA3_TC(0-1)_CFG EDMA3_CC_CFG EDMA2_TC(0-3)_CFG EDMA2_CC_CFG EDMA1_TC(0-3)_CFG EDMA1_CC_CFG EDMA0_TC(0-1)_CFG EDMA0_CC_CFG DDR3B_PHY_CFG DDR3A_PHY_CFG DBG_TBR_SYS DBG_CFG CPT_SPI_ROM_EMIF16_CFG CPT_QM_M_CFG CPT_QM_CFG2_CFG CPT_QM_CFG1_CFG CPT_MSMC(0-7)_CFG CPT_L2_(0-7)_CFG CPT_INTC(0-2)_CFG CPT_DDR3B_CFG CPT_DDR3A_CFG CPT_CFG_CFG CP_INTC_CFG BOOTCFG_CFG ARM_CFG ADTF(0-7)_CFG 10GBE_CFG MASTERS 10GbE (1) 10GBE_SERDES_CFG SLAVES - CorePac0_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac1_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac2_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac3_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac4_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac5_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac6_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac7_CFG Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y DBG_DAP Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y EDMA0_CC_TR - - - - - - - - - - - - - - - - - - - - - Y - - - - - - - EDMA0_TC0_RD - - - - - - - - - - - - - - - - - 12 - - 12 12 12 12 12 12 12 12 12 EDMA0_TC0_WR - - - - - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 EDMA0_TC1_RD - - - - - - - - - - - - - - - - - 12 - - 12 12 12 12 12 12 12 12 12 EDMA0_TC1_WR - - - - - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 EDMA1_CC_TR - - - - - - - - - - - - - - - - - - - - - - - Y - - - - - EDMA1_TC0_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 EDMA1_TC0_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 EDMA1_TC1_RD - - - - - - - - - - - - - - - - - - - - 13 13 13 13 13 13 13 13 13 EDMA1_TC1_WR - - - - - - - - - - - - - - - - - - - - 13 13 13 13 13 13 13 13 13 EDMA1_TC2_RD - - - - - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 14 EDMA1_TC2_WR - - - - - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 14 EDMA1_TC3_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 EDMA1_TC3_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 EDMA2_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - Y - - - EDMA2_TC0_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 EDMA2_TC0_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 EDMA2_TC1_RD - - - - - - - - - - - - - - - - - - - - 13 13 13 13 13 13 13 13 13 EDMA2_TC1_WR - - - - - - - - - - - - - - - - - - - - 13 13 13 13 13 13 13 13 13 EDMA2_TC2_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 EDMA2_TC2_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 EDMA2_TC3_RD - - - - - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 14 EDMA2_TC3_WR - - - - - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 14 EDMA3_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA3_TC0_RD 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 EDMA3_TC0_WR 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 EDMA3_TC1_RD - - - - - - - - - - - - - - - - - 14 - - 14 14 14 14 14 14 14 14 14 EDMA3_TC1_WR - - - - - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 14 EDMA4_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - (1) 178 66AK2H14 only. System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 9-2. Configuration Space Interconnect - Section 1 (continued) MASTERS 10GBE_CFG 10GBE_SERDES_CFG ADTF(0-7)_CFG ARM_CFG BOOTCFG_CFG CP_INTC_CFG CPT_CFG_CFG CPT_DDR3A_CFG CPT_DDR3B_CFG CPT_INTC(0-2)_CFG CPT_L2_(0-7)_CFG CPT_MSMC(0-7)_CFG CPT_QM_CFG1_CFG CPT_QM_CFG2_CFG CPT_QM_M_CFG CPT_SPI_ROM_EMIF16_CFG DBG_CFG DBG_TBR_SYS DDR3A_PHY_CFG DDR3B_PHY_CFG EDMA0_CC_CFG EDMA0_TC(0-1)_CFG EDMA1_CC_CFG EDMA1_TC(0-3)_CFG EDMA2_CC_CFG EDMA2_TC(0-3)_CFG EDMA3_CC_CFG EDMA3_TC(0-1)_CFG EDMA4_CC_CFG EDMA4_TC0_RD - - - - - - - - - - - - - - - - - 12 - - 12 12 12 12 12 12 12 12 12 EDMA4_TC0_WR - - - - - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 EDMA4_TC1_RD - - - - - - - - - - - - - - - - - 12 - - 12 12 12 12 12 12 12 12 12 EDMA4_TC1_WR - - - - - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 HyperLink0_Master 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 HyperLink1_Master 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - 12 12 12 12 12 12 12 12 12 12 12 MSMC_SYS Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y NETCP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 QM_Master1 - - - - - - - - - - - - - - - - - - - - 12 - 12 - 12 - 12 - 12 QM_Master2 - - - - - - - - - - - - - - - - - - - - 12 - 12 - 12 - 12 - 12 QM_SEC 12 - - 12 - - - - - - - - - - - - - - - - - - - - - - - - - SRIO 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 SRIO Packet DMA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - USB - - - - - - - - - - - - - - - - - 12 - - - - - - - - - - - TETB4_CFG TETB5_CFG TETB6_CFG TETB7_CFG TIMER(0-19)_CFG UART(0-1)_CFG USB_MMR_CFG USB_PHY_CFG SLAVES PCIE Table 9-3. Configuration Space Interconnect - Section 2 NETCP_SERDES_CFG HYPERLINK1_SERDES_CFG - - - - - - - - - - - - - - - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac1_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac2_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac3_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac4_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac5_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac6_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y CorePac7_CFG Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y DBG_DAP Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y EDMA0_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA0_TC0_RD 12 - - - - - - - - - - - - - - - - - - - - 12 12 - - - - - - EDMA0_TC0_WR 12 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA0_TC1_RD 12 - - - - - - - - - - - - - - - - - - - - 12 12 - - - - - - EDMA0_TC1_WR 12 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA1_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA1_TC0_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - 12 12 - - 12 12 12 12 EDMA1_TC0_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 12 EDMA1_TC1_RD 13 - - - - - - - - - - - - - - - - 13 13 - - - - 13 - - - - - EDMA1_TC1_WR 13 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA1_TC2_RD 14 - - - - - - - - - - - - - - - - - - 14 14 - - - 14 - - - - Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 TETB3_CFG - Y TETB2_CFG - Y TETB1_CFG - Y TETB0_CFG - Y TBR_SYS_ARM - Y SRIO_SERDES_CFG - Y SRIO_CFG - Y QM_CFG2 - Y QM_CFG1 - Y PSC_CFG - Y PLL_CTL_CFG - Y PCIE_SERDES_CFG - - NETCP_CFG - Y MPU(0-14)_CFG - CorePac0_CFG I2C(0-2)_CFG GIC_CFG 10GbE MASTERS GPIO_CFG EDMA4_TC(0-1)_CFG HYPERLINK0_SERDES_CFG SLAVES System Interconnect 179 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 9-3. Configuration Space Interconnect - Section 2 (continued) TETB6_CFG TETB7_CFG - - - - - - - - - - - - - - 12 12 12 - - - - 12 12 - - 12 12 12 12 EDMA1_TC3_WR 12 USB_PHY_CFG TETB5_CFG - 12 USB_MMR_CFG TETB3_CFG - 12 UART(0-1)_CFG TETB2_CFG - 12 TIMER(0-19)_CFG TETB1_CFG - 12 TETB4_CFG TETB0_CFG - 12 SRIO_SERDES_CFG - 12 SRIO_CFG - 12 QM_CFG2 - 12 QM_CFG1 - 12 PSC_CFG - 12 PLL_CTL_CFG - 12 PCIE_SERDES_CFG - 12 NETCP_CFG - 12 MPU(0-14)_CFG - 12 I2C(0-2)_CFG TBR_SYS_ARM NETCP_SERDES_CFG HYPERLINK1_SERDES_CFG 14 EDMA1_TC3_RD GPIO_CFG EDMA1_TC2_WR GIC_CFG MASTERS EDMA4_TC(0-1)_CFG HYPERLINK0_SERDES_CFG SLAVES 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 EDMA2_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA2_TC0_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - Y Y - - 12 12 12 12 EDMA2_TC0_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 12 EDMA2_TC1_RD 13 - - - - - - - - - - - - - - - - 13 13 - - - - 13 - - - - - EDMA2_TC1_WR 13 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA2_TC2_RD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - 12 12 - - 12 12 12 12 EDMA2_TC2_WR 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 12 EDMA2_TC3_RD 14 - - - - - - - - - - - - - - - - - - 14 14 - - - 14 - - - - EDMA2_TC3_WR 14 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA3_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA3_TC0_RD 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 EDMA3_TC0_WR 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 - - - - - - - - 13 13 13 13 EDMA3_TC1_RD 14 - - - - - - - - - - - - - - - - 14 14 14 14 14 14 14 14 - - - - EDMA3_TC1_WR 14 - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA4_CC_TR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - EDMA4_TC0_RD 12 - - - - - - - - - - - - - - - 12 - - - - 12 12 - - - - - - EDMA4_TC0_WR 12 - - - - - - - - - - - - - - - 12 - - - - - - - - - - - - EDMA4_TC1_RD 12 - - - - - - - - - - - - - - - 12 - - - - 12 12 - - - - - - EDMA4_TC1_WR 12 - - - - - - - - - - - - - - - 12 - - - - - - - - - - - - HyperLink0_Master 12 - 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 12 HyperLink1_Master 12 - 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 - - - - - - - - 12 12 12 12 MSMC_SYS Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y NETCP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12 - 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 QM_Master1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - QM_Master2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - QM_SEC - - - - - - - 12 - - - - - - - - 12 - - - - - - - - - - 12 - 14 - 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 SRIO Packet DMA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - USB - - - - - - - - - - - - - - - - 12 12 12 12 12 12 12 12 12 - - - - PCIE SRIO 180 System Interconnect Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com 9.4 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Bus Priorities The priority level of all master peripheral traffic is defined at the TeraNet boundary. User-programmable priority registers allow software configuration of the data traffic through the TeraNet. Note that a lower number means higher priority — PRI = 000b = urgent, PRI = 111b = low. All other masters provide their priority directly and do not need a default priority setting. Examples include the C66x CorePacs, whose priorities are set through software in the UMC control registers. All the Packet DMA-based peripherals also have internal registers to define the priority level of their initiated transactions. The Packet DMA secondary port is one master port that does not have priority allocation register inside the Multicore Navigator. The priority level for transaction from this master port is described by the QM_PRIORITY bit field in the CHIP_MISC_CTL0 register shown in Section 10.2.3.24. For all other modules, see the respective User's Guides listed in Section 12.3 for programmable priority registers. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 System Interconnect 181 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 10 Device Boot and Configuration 10.1 Device Boot 10.1.1 Boot Sequence The boot sequence is a process by which the internal memory is loaded with program and data sections. The boot sequence is started automatically after each power-on reset or warm reset. The 66AK2Hxx supports several boot processes that begin execution at the ROM base address, which contains the bootloader code necessary to support various device boot modes. The boot processes are software-driven and use the BOOTMODE[15:0] device configuration inputs to determine the software configuration that must be completed. For more details on boot sequence, see the KeyStone II Architecture ARM Bootloader User's Guide. For 66AK2Hxx nonsecure devices, there are two types of booting: the C66x CorePac as the boot master and the ARM CorePac as the boot master. For secure devices, the C66x CorePac is always the secure master and the C66x CorePac0 or ARM CorePac Core0 can be the boot master. The ARM CorePac does not support no-boot mode. Both the C66x CorePacs and the ARM CorePac need to read the BOOTMODE register to determine how to proceed with the boot. Table 10-1 shows memory space reserved for boot by the C66x CorePac. Table 10-1. C66x DSP Boot RAM Memory Map START ADDRESS SIZE 0x80_0000 0x1_0000 DESCRIPTION Reserved 0x8e_7f80 0x80 0x8e_8000 0x7f00 C66x CorePac ROM version string 0x8e_767c 4 Boot Master Table Valid Length Field 0x8e_fff0 4 Host Data Address (boot magic address for secure boot through master peripherals) Boot Master Table overlayed with scratch 0x8f_7800 0x410 Secure host Data structure 0x8f_a290 0x4000 Boot Stack 0x8f_e290 0x90 Boot Log Data 0x8f_e320 0x20 Boot Status Stack 0x8f_e410 0xf0 Boot Stats 0x8f_e520 0x13fc Boot Data 0x8f_f91c 0x404 Boot Trace Info 0x8f_fd20 0x180 DDR Config 0x8f_fea0 0x60 Boot RAM call table 0x8f_ff00 0x80 Boot Parameter table 0x8f_fff8 0x4 Secure Signal Magic address 0x8f_fffc 0x4 Boot Magic address Table 10-2 shows addresses reserved for boot by the ARM CorePac. Table 10-2. ARM Boot RAM Memory Map START ADDRESS SIZE DESCRIPTION 0xc57_e000 0xc00 Context RAM not scrubbed on secure boot 0xc58_6f80 0x80 Global level 0 nonsecure translation table 0xc58_7000 0x5000 Global nonsecure page table for memory covering ROM 0xc58_c000 0x1000 Core 0 nonsecure level 1 translation table 0xc58_d000 0x1000 Core 1 nonsecure level 1 translation table 0xc58_e000 0x1000 Core 2 nonsecure level 1 translation table 182 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-2. ARM Boot RAM Memory Map (continued) START ADDRESS SIZE DESCRIPTION 0xc58_f000 0x1000 Core 3 nonsecure level 1 translation table 0xc59_0000 0x7f00 Packet memory buffer 0xc59_7f00 4 Host Data Address (boot magic address for secure boot through master peripherals) 0xc5a_6e00 0x200 DDR3a configuration structure 0xc5a_7000 0x3000 Boot Data 0xc5a_a000 0x3000 Supervisor stack, each core gets 0xc00 bytes 0xc5a_d000 4 Arm boot magic address, core 0 0xc5a_d004 4 Arm boot magic address, core 1 0xc5a_d008 4 Arm boot magic address, core 2 0xc5a_d00c 4 Arm boot magic address, core 3 0xc5a_e000 0x400 Abort stack, core 0 0xc5a_e400 0x400 Abort stack, core 1 0xc5a_e800 0x400 Abort stack, core 2 0xc5a_ec00 0x400 Abort stack, core 3 0xc5a_f000 0x400 Unknown mode stack, core 0 0xc5a_f400 0x400 Unknown mode stack, core 1 0xc5a_f800 0x400 Unknown mode stack, core 2 0xc5a_fc00 0x400 Unknown mode stack, core 3 0xc5b_0000 0x180 Boot Version string, core 0 0xc5b_0180 0x80 Boot status stack, core 0 0xc5b_0200 0x100 Boot stats, core 0 0xc5b_0300 0x100 Boot log, core 0 0x5b_0400 0x100 Boot RAM call table, core 0 0xc5b_0500 0x100 Boot parameter tables, core 0 0xc5b_0600 0x19e0 Boot Data, core 0 0xc5b_1fe0 0x1010 Boot Trace, core 0 0xc5b_4000 0x180 Boot Version string, core 1 0xc5b_4180 0x80 Boot status stack, core 1 0xc5b_4200 0x100 Boot stats, core 1 0xc5b_4300 0x100 Boot log, core 1 0x5b_4400 0x100 Boot RAM call table, core 1 0xc5b_4500 0x100 Boot parameter tables, core 1 0xc5b_4600 0x19e0 Boot Data, core 1 0xc5b_5fe0 0x1010 Boot Trace, core 1 0xc5b_8000 0x180 Boot Version string, core 2 0xc5b_8180 0x80 Boot status stack, core 2 0xc5b_8200 0x100 Boot stats, core 2 0xc5b_8300 0x100 Boot log, core 2 0x5b_8400 0x100 Boot RAM call table, core 2 0xc5b_8500 0x100 Boot parameter tables, core 2 0xc5b_8600 0x19e0 Boot Data, core 2 0xc5b_9fe0 0x1010 Boot Trace, core 2 0xc5b_c000 0x180 Boot Version string, core 3 0xc5b_c180 0x80 Boot status stack, core 3 0xc5b_c200 0x100 Boot stats, core 3 0xc5b_c300 0x100 Boot log, core 3 0x5b_c400 0x100 Boot RAM call table, core 3 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 183 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-2. ARM Boot RAM Memory Map (continued) START ADDRESS SIZE DESCRIPTION 0xc5b_c500 0x100 Boot parameter tables, core 3 0xc5b_c600 0x19e0 Boot Data, core 3 0xc5b_dfe0 0x1010 Boot Trace, core 3 0xc5c_0000 0x4_0000 Secure MSMC 10.1.2 Boot Modes Supported The device supports several boot processes, which leverage the internal boot ROM. Most boot processes are software-driven, using the BOOTMODE[15:0] device configuration inputs to determine the software configuration that must be completed. From a hardware perspective, there are four possible boot modes: • Public ROM Boot when the C66x CorePac0 is the boot master — The C66x CorePac is released from reset and begins executing from the L3 ROM base address. The ARM CorePac is also released from reset at the same time as the C66xCorePac. Both the C66x CorePac and the ARM CorePac read the BOOTMODE register inside the bootCFG module to determine which is the boot master. After the Boot ROM for the Cortex-A15 processor reads the BOOTMODE to determine that the C66x CorePac is the boot master, all Cortex-A15 processors stay idle by executing WFI instruction and waiting for the C66x CorePac’s interrupt. The chip Boot ROM reads the BOOTMODE register to determine that the C66x CorePac0 is the boot master, then the C66x CorePac0 performs the boot process and the other C66x CorePacs execute an IDLE instruction. After the boot process is completed, the C66x CorePac0 begins to execute the code downloaded during the boot process. If the downloaded code included code for the other C66x cores and/or the Cortex-A15 processor cores, the downloaded code may contain logic to write the code execution addresses to the boot address register for the core that is to execute it. The C66x CorePac0 can then generate an interrupt to the core causing it to execute the code. When they receive the IPC interrupt, the rest of the C66x CorePacs and the ARM CorePac complete boot management operations and begin executing from the predefined location in memory. • Public ROM Boot when the ARM CorePac Core0 is the boot master — The only difference between this boot mode and when the C66x CorePac is the boot master, is that the ARM CorePac performs the boot process while the C66x CorePacs execute idle instructions. When the ARM CorePac Core0 finishes the boot process, it may send interrupts to the C66x CorePacs and Cortex-A15 processor cores through IPC registers. The C66x CorePacs complete the boot management operations and begin executing from the predefined locations. • Secure ROM Boot when the C66x CorePac0 is the boot master —The C66x CorePac0 and the ARM CorePac Core0 are released from reset simultaneously and the C66x CorePac0 begins executing from secure ROM. The C66x CorePac0 performs the boot process including any authentication and decryption required on the bootloaded image for the C66x CorePacs and for the ARM CorePac prior to beginning execution. • Secure ROM Boot when the ARM CorePac0 is the boot master — The C66x CorePac0 and the ARM CorePac Core0 are released from reset simultaneously and begin executing from secure ROM. The ARM CorePac Core0 initiates the boot process. The C66x CorePac0 performs any authentication and decryption required on the bootloaded image for the C66x CorePacs and ARM CorePac prior to beginning execution. The boot process performed by the C66x CorePac0 and the ARM CorePac Core0 in public ROM boot and secure ROM boot are determined by the BOOTMODE[15:0] value in the DEVSTAT register. The C66x CorePac0 and the ARM CorePac Core0 read this value, and then execute the associated boot process in software. Bit 8 determines whether the boot is C66x CorePac boot or ARM CorePac boot. The figure below shows the bits associated with BOOTMODE[15:0] (DEVSTAT[16:1]) when the C66x CorePac or ARM CorePac is the boot master. Figure 10-1 does not include bit 0 of the DEVSTAT contents. Bit 0 is used to select overall system endianess that is independent of the boot mode. 184 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 The boot ROM will continue attempting to boot in this mode until successful or an unrecoverable error occurs. The PLL settings are shown at the end of this section, and the PLL set-up details can be found in Section 11.5. NOTE It is important to remember that the BOOTMODE[15:0] pins map to the DEVSTAT[16:1] bits of the DEVSTAT register. Figure 10-1. DEVSTAT Boot Mode Pins ROM Mapping 16 15 14 X X 0 SlaveAddr 1 X X X Width Csel 0 Base Addr 13 12 ARMEN SYSEN Port Bus Addr Mode Wait Width 11 DEVSTAT Boot Mode Pins ROM Mapping 10 9 8 7 6 5 3 0 0 0 0 2 0 0 0 1 1 0 0 1 0 0 1 1 1 0 0 1 0 1 0 1 1 0 1 1 1 0 Min 1 1 1 SYS PLL CONFIG ARM PLL CONFIG X Npin Param ldx Min Port ARM PLL CONFIG X 4 0 Chip Sel ARM PLL CONFIG 1 First Block Clear X Lane Ref Clock Data Rate Chip Sel ARM PLL CONFIG X ARM PLL CONFIG PA clk Ref clk Ext Con Rsvd Ref clk Lane Setup ARM PLL CONFIG SerDes Cfg Bar Config Min Boot Master Lane Setup SYS PLL CONFIG ARM PLL CONFIG Port Ref clk Data Rate SerDes Cfg X X X X ARM PLL CONFIG Port X X X X X X X Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Mode SLEEP I2C SLAVE 2 I C MASTER SPI EMIF (ARM Master) EMIF (DSP Master) NAND (ARM Master) NAND (DSP Master) SRIO (ARM Master) SRIO (DSP Master) Ethernet (ARM Master) Ethernet (DSP Master) PCIe (ARM Master) PCIe (DSP Master) HyperLink (ARM Master) HyperLink (DSP Master) UART (ARM Master) UART (DSP Master) Device Boot and Configuration 185 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 10.1.2.1 Boot Device Field The Boot Device field BOOTMODE[16-14-4-3-2-1] bits define the boot device that is chosen and the BOOTMODE[8] bit defines the boot master that is chosen. Table 10-3 shows the supported boot modes. Table 10-3. Boot Mode Pins: Boot Device Values Bit Field Description 16, 14, 4, 3, 2, 1 Boot Device Device boot mode • ARM is a boot master when BOOTMODE[8]=0 – Sleep = X0[Min]000b – I2C Slave = [Slave Addr1]1[Min]000b – I2C Master = X1[Min]001b – SPI = [Width][Csel0][Min]010b – EMIF = 0[BaseAddr0][Min]011b – NAND = 1[BaseAddr0][Min]011b – Serial Rapid I/O = [Lane][Ref Clock0][Min]100b – Ethernet (SGMII) = [Pa clk][Ref Clk0][Min]101b – PCI = [Ref clk][Bar Config2]0110b – HyperLink = [Port][Ref Clk0]1110b – UART = XX[Min]111b • C66x is a boot master when BOOTMODE[8]=1 – Sleep = X0[Min]000b – I2C Slave = [Slave Addr1]1[Min]000b – I2C Master = X1[Min]001b – SPI = [Width][Csel0][Min]010b – EMIF = 0[BaseAddr0][Min]011b – NAND = 1[BaseAddr0][Min]011b – Serial Rapid I/O = [Lane][Ref Clock0][Min]100b – Ethernet (SGMII) = [Pa clk][Ref Clk0][Min]101b – PCI = [Ref clk][Bar Config2]0110b – HyperLink = [Port][Ref Clk0]1110b – UART = XX[Min]111b 10.1.2.2 Device Configuration Field The device configuration fields DEVSTAT[16:1] are used to configure the boot peripheral and, therefore, the bit definitions depend on the boot mode. 10.1.2.2.1 Sleep Boot Mode Configuration Figure 10-2. Sleep Boot Mode Configuration Fields 16 15 14 X X 0 13 12 ARMen SYSEN DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 6 5 Boot ARM PLL Cfg Sys PLL Config Master 4 3 Min 2 000 1 0 Lendian Table 10-4. Sleep Boot Configuration Field Descriptions Bit Field Description 16-15 Reserved Reserved 14 Boot Devices Boot Device- used in conjunction with Boot Devices [Used in conjunction with bits 3-1] • 0 = Sleep (default) • Others = Other boot modes 13 ARMen Enable the ARM PLL • 0 = PLL disabled • 1 = PLL enabled 186 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-4. Sleep Boot Configuration Field Descriptions (continued) Bit Field Description 12 SYSEN Enable the System PLL • 0 = PLL disabled (default) • 1 = PLL enabled 11-9 ARM PLL Setting The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 8 Boot Master Boot Master select • 0 = ARM is boot master • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices[3:1] used in conjunction with Boot Device [14] • 000 = Sleep • Others = Other boot modes 0 Lendian Endianess (device) • 0 = Big endian • 1 = Little endian 10.1.2.2.2 I2C Boot Device Configuration 10.1.2.2.2.1 I2C Passive Mode In passive mode, the device does not drive the clock, but simply acks data received on the specified address. Figure 10-3. I2C Passive Mode Device Configuration Fields 16 15 14 Slave Addr 1 13 12 Port 11 DEVSTAT Boot Mode Pins ROM Mapping 10 9 8 7 6 5 Boot ARM PLL Cfg Sys PLL Config Master 4 Min 3 2 1 000 0 Lendian Table 10-5. I2C Passive Mode Device Configuration Field Descriptions Bit Field Description 16-15 Slave Addr I2C • • • • Slave boot bus address 0 = I2C slave boot bus address 1 = I2C slave boot bus address 2 = I2C slave boot bus address 3 = I2C slave boot bus address is is is is 0x00 0x10 (default) 0x20 0x30 14 Boot Devices Boot Device[14] used in conjunction with Boot Devices [Use din conjunction with bits 3-1] • 0 = Other boot modes • 1= I2C Slave boot mode 13-12 Port I2C • • • • 11-9 ARM PLL Setting The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. port number 0 = I2C0 1 = I2C1 2 = I2C2 3 = Reserved Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 187 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-5. I2C Passive Mode Device Configuration Field Descriptions (continued) Bit Field Description 8 Boot Master Boot Master select • 0 = ARM is boot master • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices[3:1] used in conjunction with Boot Device [14] • 000 = I2C Slave • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.2.2.2 I2C Master Mode In master mode, the I2C device configuration uses 10 bits of device configuration instead of seven as used in other boot modes. In this mode, the device makes the initial read of the I2C EEPROM while the PLL is in bypass mode. The initial read contains the desired clock multiplier, which must be set up prior to any subsequent reads. Figure 10-4. I2C Master Mode Device Configuration Fields 16 15 14 Reserved 13 12 Bus Addr DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 Param ldx/Offset Boot Master Reserved 6 5 Port 4 Min 3 2 1 001 0 Lendian Table 10-6. I2C Master Mode Device Configuration Field Descriptions Bit Field Description 16-14 Reserved Reserved 13-12 Bus Addr I2C • • • • 11-9 Param Idx/Offset bus address slave device 0 = I2C slave boot bus address 1 = I2C slave boot bus address 2 = I2C slave boot bus address 3 = I2C slave boot bus address is is is is 0x50 (default) 0x51 0x52 0x53 Parameter Table Index: 0-7 This value specifies the parameter table index when the C66x is the boot master This value specifies the start read address at 8K times this value when the ARM is the boot master 8 Boot Master Boot Master select • 0 = ARM is boot master • 1 = C66x is boot master 7 Reserved • Reserved 6-5 Port I2C • • • • port number 0 = I2C0 (default) 1 = I2C1 2 = I2C2 3 = Reserved 188 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-6. I2C Master Mode Device Configuration Field Descriptions (continued) Bit Field Description 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices[3:1] • 001 = I2C Master • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.2.3 SPI Boot Device Configuration Figure 10-5. SPI Device Configuration Fields 16 Width 15 14 Csel 13 12 Mode DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 Param ldx/Offset Boot Master Npin 6 5 Port 4 Min 3 2 1 010 0 Lendian Table 10-7. SPI Device Configuration Field Descriptions Bit Field Description 16 Width SPI address width configuration • 0 = 16-bit address values are used • 1 = 24-bit address values are used (default) 15-14 Csel The chip select field value 0-3 (default = 0) 13-12 Mode Clk Polarity/ Phase • 0 = Data is output on the rising edge of SPICLK. Input data is latched on the falling edge. • 1 = Data is output one half-cycle before the first rising edge of SPICLK and on subsequent falling edges. Input data is latched on the rising edge of SPICLK. • 2 = Data is output on the falling edge of SPICLK. Input data is latched on the rising edge (default). • 3 = Data is output one half-cycle before the first falling edge of SPICLK and on subsequent rising edges. Input data is latched on the falling edge of SPICLK. 11-9 Param Idx/Offset Parameter Table Index: 0-7 This value specifies the parameter table index when the C66x is the boot master This value specifies the start read address at 8K times this value when the ARM is the boot master 8 Boot Master Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master 7 Npin Selected Chip Select driven • 0 = CS0 to the selected chip select is driven • 1 = CS0-CS3 to the selected chip select are driven (default) 6-5 Port Specify SPI port • 0 = SPI0 used (default) • 1 = SPI1 used • 2 = SPI2 used • 3 = Reserved Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 189 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-7. SPI Device Configuration Field Descriptions (continued) Bit Field Description 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices[3:1] • 010 = SPI boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.2.4 EMIF Boot Device Configuration Figure 10-6. EMIF Boot Device Configuration Fields 16 0 0 15 14 Base Addr Base Addr 13 Wait Wait 12 Width Width DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 X Chip Sel Boot Master=1 ARM PLL Cfg Boot Master=0 7 6 5 Sys PLL Cfg Sys PLL Cfg 4 0 0 3 2 1 011 011 0 Lendian Lendian Table 10-8. EMIF Boot Device Configuration Field Descriptions Bit Field Description 16 Boot Devices Boot Devices[16] used conjunction with Boot Devices[4] and Boot Devices [Used in conjunction with bits 3-1] • 0 = EMIF boot mode • 1 = Other boot modes 15-14 Base Addr Base address (0-3) used to calculate the branch address. Branch address is the chip select plus Base Address *16MB 13 Wait Extended Wait • 0 = Extended Wait disabled • 1 = Extended Wait enabled 12 Width EMIF Width • 0 = 8-bit EMIF Width • 1 = 16-bit EMIF Width 11-9 Chip Sel/ARM PLL Setting When Boot Master = 0 (ARM is Boot Master), Pin[11:9] used as ARM PLL Setting and the chip select region CS0 is used. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. When Boot Master =1 (C66x is Boot Master), Pin[10:9] used as Chip Sel that specifies the chip select region, CS0-CS3. • 00 = CS0 (EMIFCE0) • 01 = CS1 (EMIFCE1) • 10 = CS2 (EMIFCE2) • 11 = CS3 (EMIFCE3) 8 Boot Master Boot Master select • 0 = ARM is boot master • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 190 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-8. EMIF Boot Device Configuration Field Descriptions (continued) Bit Field Description 4 Boot Devices Boot Devices[4] used conjunction with Boot Devices[16] and Boot Devices [Use din conjunction with bits 3-1] • 0 = EMIF boot mode • 1 = Other boot modes 3-1 Boot Devices Boot Devices[3:1] used in conjunction with Boot Device [4] • 011 = EMIF boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.2.5 NAND Boot Device Configuration Figure 10-7. NAND Boot Device Configuration Fields 16 1 1 15 14 13 First Block First Block 12 Clear Clear DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 6 5 X Chip Sel Boot Master=1 Sys PLL Cfg ARM PLL Cfg Boot Master=0 Sys PLL Cfg 4 Min Min 3 2 011 011 1 0 Lendian Lendian Table 10-9. NAND Boot Device Configuration Field Descriptions Bit Field Description 16 Boot Devices Boot Devices[16] used conjunction with Boot Devices [3-1] • 0 = Other boot modes • 1 = NAND boot mode 15-13 First Block First Block. This value is used to calculate the first block read. The first block read is the first block value *16. 12 Clear ClearNAND • 0 = Device is not a ClearNAND (default) • 1 = Device is a ClearNAND 11-9 Chip Sel/ARM PLL Setting When Boot Master = 0 (ARM is Boot Master), Pin[11:9] used as ARM PLL Setting and the chip select region CS2 is used. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. When Boot Master =1 (C66x is Boot Master), Pin[10:9] used as Chip Sel that specifies the chip select region, CS2-CS5. • 00 = CS2 • 01 = CS3 • 10 = CS4 • 11 = CS5 8 Boot Master Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 4 Min Minimum boot pin select. When Min is 1, it means that the BOOTMODE [15:3] pins are don't cares. Only BOOTMODE [2:0] pins (DEVSTAT[3:1]) will determine boot. Default values are assigned to values that would normally be set by the other BOOTMODE pins when Min is 0. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. 3-1 Boot Devices Boot Devices • 011 = NAND boot mode • Others = Other boot modes Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 191 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-9. NAND Boot Device Configuration Field Descriptions (continued) Bit Field Description 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.3 Serial Rapid I/O Boot Device Configuration The device ID is always set to 0xff (8-bit node IDs) or 0xffff (16 bit node IDs) at power-on reset. Figure 10-8. Serial Rapid I/O Boot Device Configuration Fields 16 X Lane 15 14 Ref Clock Ref Clock 13 12 Data Rate Data Rate DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 6 5 Lane Setup Boot Master=1 Sys PLL Cfg ARM PLL Cfg Boot Master=0 Sys PLL Cfg 4 Min Min 3 2 1 100 100 0 Lendian Lendian Table 10-10. Serial Rapid I/O Boot Device Configuration Field Descriptions Bit Field Description 16 Lane When Boot Master =0 (ARM is Boot Master), Pin[16] is used as Lane. • 0 = 4 ports, each 1 lane wide (default) • 1 = 2 ports, each 2 lanes wide When Boot Master =1 (C66x is Boot Master), Pin[16] is reserved. 15-14 Ref Clock SRIO Reference clock frequency • 0 = 125 MHz • 1 = 156.25 MHz (default) • 2 = Reserved • 3 = Reserved 13-12 Data Rate SRIO Data Rate • 0 = 1.25GB • 1 = 2.5GB • 2 = 3.125GB • 3 = 5GB (default) 11-9 Lane Setup/ARM PLL Setting When Boot Master =0 (ARM is Boot Master), pin[11:9] used as ARM PLL Setting with all lanes enabled. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. The default value is 156.26 MHz. Table 10-27 shows settings for various input clock frequencies. When Boot Master =1 (C66x is Boot Master), pin [11:9] are used as Lane Set up. • 0 = 4 ports, each 1 lane wide (default) • 1 = 3 ports, lanes 0, 1 form a 2 lane port, lane 2,3 are single ports • 2 = 3 ports, lanes 0, 1 are single lane ports, lanes 2,3 form a 2 lane port • 3 = 2 ports, lane 0, 1 are one port, lane 2, 3 are a second port • 4 = 1 port, 4 lanes wide • 5-7 = 4 ports, each 1 lane wide 8 Boot Master Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Default system reference clock is 156.25 MHz. Table 10-27 shows settings for various input clock frequencies. (default = 4) 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 192 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-10. Serial Rapid I/O Boot Device Configuration Field Descriptions (continued) Bit Field Description 3-1 Boot Devices Boot Devices • 100 = SRIO boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian In SRIO boot mode, both the message mode and DirectIO mode will be enabled by default. If use of the memory reserved for received messages is required and reception of messages cannot be prevented, the master can disable the message mode by writing to the boot table and generating a boot restart. 10.1.2.4 Ethernet (SGMII) Boot Device Configuration Figure 10-9. Ethernet (SGMII) Boot Device Configuration Fields 16 Pa clk Pa clk 15 14 Ref Clock Ref Clock 13 12 Ext Con Ext Con DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 6 5 Lane Setup Boot Master=1 Sys PLL Cfg ARM PLL Cfg Boot Master=0 Sys PLL Cfg 4 Min Min 3 2 1 101 101 0 Lendian Lendian Table 10-11. Ethernet (SGMII) Boot Device Configuration Field Descriptions Bit Field Description 16 Pa clk PA clock reference • 0 = PA clocked at the same reference as the core reference • 1 = PA clocked at the same reference as the SerDes reference (default) 15-14 Ref Clock SRIO Reference clock frequency • 0 = 125 MHz • 1 = 156.25 MHz (default) • 2 = Reserved • 3 = Reserved 13-12 Ext Con External connection mode • 0 = MAC to MAC connection, master with auto negotiation • 1 = MAC to MAC connection, slave with auto negotiation (default) • 2 = MAC to MAC, forced link, maximum speed • 3 = MAC to fiber connection 11-9 Lane Setup/ARM PLL Setting When Boot Master = 0 (ARM is Boot Master), pin[11:9] used as ARM PLL Setting. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. When Boot Master =1 (C66x is Boot Master), pin [10:9] are used as Lane Set up. • 0 = All SGMII ports enabled (default) • 1 = Only SGMII port 0 enabled • 2 = SGMII port 0 and 1 enabled • 3 = SGMII port 0, 1 and 2 enabled • 4-7 = Reserved 8 Boot Master Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Default system reference clock is 156.25 MHz. Table 10-27 shows settings for various input clock frequencies. (default = 4) Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 193 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-11. Ethernet (SGMII) Boot Device Configuration Field Descriptions (continued) Bit Field Description 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices • 101 = Ethernet boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.4.1 PCIe Boot Device Configuration Figure 10-10. PCIe Boot Device Configuration Fields 16 Ref clk Ref clk 15 14 13 Bar Config Bar Config 12 DEVSTAT Boot Mode Pins ROM Mapping 10 9 8 7 6 5 Reserved Boot Master=1 Sys PLL Cfg ARM PLL Cfg Boot Master=0 Sys PLL Cfg 11 4 3 2 0110 0110 1 0 Lendian Lendian Table 10-12. PCIe Boot Device Configuration Field Descriptions Bit Field Description 16 Ref clk PCIe Reference clock frequency • 0 = 100MHz • 1 = Reserved 15-12 Bar Config PCIe BAR registers configuration This value can range from 0 to 0xf. See Table 10-13. 11-9 Reserved/ARM PLL Setting When Boot Master =0 (ARM is Boot Master), pin[11:9] used as ARM PLL Setting. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 8 Boot Master Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Default system reference clock is 156.25 MHz. Table 10-27 shows settings for various input clock frequencies. 4-1 Boot Devices Boot Devices[4:1] • 0110 = PCIe boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian When Boot Master =1 (C66x is Boot Master), pin [10:9] are reserved. 194 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-13. BAR Config / PCIe Window Sizes 64-BIT ADDRESS TRANSLATION 32-BIT ADDRESS TRANSLATION BAR CFG BAR0 BAR1 BAR2 BAR3 BAR4 0b0000 PCIe MMRs 32 32 32 32 0b0001 16 16 32 64 0b0010 16 32 32 64 0b0011 32 32 32 64 0b0100 16 16 64 64 0b0101 16 32 64 64 0b0110 32 32 64 64 0b0111 32 32 64 128 0b1000 64 64 128 256 0b1001 4 128 128 128 0b1010 4 128 128 256 0b1011 4 128 256 256 BAR5 BAR2/3 BAR4/5 0b1100 256 256 0b1101 512 512 0b1110 1024 1024 0b1111 2048 2048 Clone of BAR4 10.1.2.4.2 HyperLink Boot Device Configuration Figure 10-11. HyperLink Boot Device Configuration Fields 16 Port Port 15 14 RefClk RefClk 13 12 Data Rate Data Rate DEVSTAT Boot Mode Pins ROM Mapping 10 9 8 7 6 5 Reserved Boot Master=1 Sys PLL Cfg ARM PLL Cfg Boot Master=0 Sys PLL Cfg 11 4 3 2 1110 1110 1 0 Lendian Lendian Table 10-14. HyperLink Boot Device Configuration Field Descriptions Bit Field Description 16 Port HyperLink port • 0 = HyperLink0 • 1 = HyperLink1 15-14 Ref Clocks HyperLink reference clock configuration • 0 = 125 MHz • 1 = 156.25 MHz • 2-3 = Reserved 13-12 Data Rate HyperLink data rate configuration • 0 = 1.25 GBs • 1 = 3.125 GBs • 2 = 6.25 GBs • 3 = 12.5 GBs 11-9 Reserved/ARM PLL Setting When Boot Master =0 (ARM is Boot Master), pin[11:9] used as ARM PLL Setting. The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 8 Boot Master When Boot Master =1 (C66x is Boot Master), pin [10:9] are reserved. Boot Master select • 0 = ARM is boot master (default) • 1 = C66x is boot master Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 195 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-14. HyperLink Boot Device Configuration Field Descriptions (continued) Bit Field Description 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Default system reference clock is 156.25 MHz. Table 10-27 shows settings for various input clock frequencies. 4-1 Boot Devices Boot Devices[4:1] • 1110 = HyperLink boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.4.3 UART Boot Device Configuration Figure 10-12. UART Boot Mode Configuration Field Description 16 X X 15 X X 14 X X 13 X X DEVSTAT Boot Mode Pins ROM Mapping 11 10 9 8 7 6 5 X X X Boot Master=1 Sys PLL Config ARM PLL Cfg Boot Master=0 Sys PLL Config 12 Port Port 4 Min Min 3 2 1 111 111 0 Lendian Lendian Table 10-15. UART Boot Configuration Field Descriptions Bit Field Description 16-13 Reserved Not Used 12 Port UART Port number • 0 = UART0 • 1 = UART1 11-9 ARM PLL Setting The PLL default settings are determined by the [11:9] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. 8 Boot Master Boot Master select • 0 = ARM is boot master • 1 = C66x is boot master 7-5 SYS PLL Setting The PLL default settings are determined by the [7:5] bits. This will set the PLL to the maximum clock setting for the device. Table 10-27 shows settings for various input clock frequencies. (default = 4) 4 Min Minimum boot configuration select bit. • 0 = Minimum boot pin select disabled • 1 = Minimum boot pin select enabled. When Min = 1, a predetermined set of values is configured (see the Device Configuration Field Descriptions table for configuration bits with a "(default)" tag added in the description column). When Min = 0, all fields must be independently configured. 3-1 Boot Devices Boot Devices[3:1] • 111 = UART boot mode • Others = Other boot modes 0 Lendian Endianess • 0 = Big endian • 1 = Little endian 10.1.2.5 Boot Parameter Table The ROM Bootloader (RBL) uses a set of tables to carry out the boot process. The boot parameter table is the most common format the RBL employs to determine the boot flow. These boot parameter tables have certain parameters common across all the boot modes, while the rest of the parameters are unique to the boot modes. The common entries in the boot parameter table are shown in Table 10-16. 196 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-16. Boot Parameter Table Common Parameters BYTE OFFSET NAME DESCRIPTION 0 Length The length of the table, including the length field, in bytes. 2 Checksum The 16 bits ones complement of the ones complement of the entire table. A value of 0 will disable checksum verification of the table by the boot ROM. 4 Boot Mode Internal values used by RBL for different boot modes. 6 Port Num Identifies the device port number to boot from, if applicable 8 SW PLL, MSW PLL configuration, MSW 10 SW PLL, LSW PLL configuration, LSW 12 Sec PLL Config, MSW ARM PLL configuration, MSW 14 Sec PLL Config, LSW ARM PLL configuration, LSW 16 System Freq The frequency of the system clock in MHz 18 Core Freq The frequency of the core clock in MHz 20 Boot Master Set to TRUE if C66x is the master core. 10.1.2.5.1 EMIF16 Boot Parameter Table Table 10-17. EMIF16 Boot Parameter Table CONFIGURED THROUGH BOOT CONFIGURATION PINS BYTE OFFSET NAME DESCRIPTION 22 Options Async Config Parameters are used. • 0 = Value in the async config paramters are not used to program async config registers. • 1 = Value in the async config paramters are used to program async config registers. NO 24 Type Set to 0 for EMIF16 (NOR) boot NO 26 Branch Address MSW Most significant bit for Branch address (depends on chip select) YES 28 Branch Address LSW Least significant bit for Branch address (depends on chip select) YES 30 Chip Select Chip Select for the NOR flash YES 32 Memory Width Memory width of the EMIF16 bus (16 bits) YES 34 Wait Enable Extended wait mode enabled • 0 = Wait enable is disabled • 1 = Wait enable is enabled YES 36 Async Config MSW Async Config Register MSW NO 38 Async Config LSW Async Config Register LSW NO Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 197 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 10.1.2.5.2 www.ti.com SRIO Boot Parameter Table Table 10-18. SRIO Boot Parameter Table BYTE OFFSET NAME DESCRIPTION 22 Options Bit 0 Tx enable • 0 = SRIO Transmit disable • 1 = SRIO Transmit Enable CONFIGURED THROUGH BOOT CONFIGURATION PINS NO Bit 1 Mailbox Enable • 0 = Mailbox mode disabled. (SRIO boot is in DirectIO mode). • 1 = Mailbox mode enabled. (SRIO boot is in Messaging mode). Bit 2 Bypass Configuration • 0 = Configure the SRIO • 1 = Bypass SRIO configuration Bit 3 Bypass QM Configuration • 0 = Configure the QM and CPDMA • 1 = Bypass the QM and CPDMA configuration Bit 4 PLL setup • 0 = SERDES Configuration registers are taken without modification. • 1 = SERDES Configuration are modified based on the reference clock and link rate. Bit 5-15 = Reserved 24 Lane Setup • • • • • • YES (but not all lane setup are possible through the boot configuration pins) 26 Reserved Reserved NA 28 Node ID The node ID value to set for this device NO 30 SerDes ref clk The SerDes reference clock frequency, in 1/100 MHZ YES 32 Link Rate Link rate, MHz YES 34 PF Low Packet forward address range, low value NO 36 PF High Packet Forward address range, high value NO 38 Promiscuous Mask The bit is set for each lane/port that is configured as promiscuous NO 40 Time-out Sec Number of seconds before time-out. The value 0 disables the time-out. NO 44 SERDES Aux, MSW SERDES Auxillary Register Configuration, MSW NO 48 SERDES Aux, LSW SERDES Auxillary Register Configuration, LSW NO 52 SERDES Rx Lane0 MSW SERDES Rx Configuration, Lane0, MSW NO 56 SERDES Rx Lane0 LSW SERDES Rx Configuration, Lane0, LSW NO 60 SERDES Rx Lane1 MSW SERDES Rx Configuration, Lane1, MSW NO 64 SERDES Rx Lane1 LSW SERDES Rx Configuration, Lane1, LSW NO 68 SERDES Rx Lane2 MSW SERDES Rx Configuration, Lane2, MSW NO 72 SERDES Rx Lane2 LSW SERDES Rx Configuration, Lane2, LSW NO 76 SERDES Rx Lane3 MSW SERDES Rx Configuration, Lane3, MSW NO 198 Device Boot and Configuration 0b0000 = SRIO configured as four 1x ports 0b0001 = SRIO configured as 3 ports (2x, 1x, 1x) 0b0010 = SRIO configured as 3 ports (1x, 1x, 2x) 0b0011 =SRIO configured as 2 ports (2x, 2x) 0b0100 = SRIO configured as 1 4x port 0b 0101-0bffff = Reserved Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-18. SRIO Boot Parameter Table (continued) BYTE OFFSET 80 NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS SERDES Rx Lane3 LSW SERDES Rx Configuration, Lane3, LSW NO 10.1.2.5.3 Ethernet Boot Parameter Table Table 10-19. Ethernet Boot Parameter Table BYTE OFFSET NAME DESCRIPTION 22 Options Bits 02-00 Interface • 000-100 = Reserved • 101 = SGMII • 110 = Reserved • 111 = Reserved CONFIGURED THROUGH BOOT CONFIGURATION PINS NO Bits 03 HD • 0 = Half Duplex • 1 = Full Duplex Bit 4 Skip TX • 0 = Send Ethernet Ready Frame every 3 seconds • 1 = Don't send Ethernet Ready Frame Bits 06-05 Initialize Config • 00 = Switch, SerDes, SGMII and PASS are configured • 01 = Initialization is not done for the peripherals that are already enabled and running. • 10 = Reserved • 11 = None of the Ethernet system is configured. Bits 15-07 Reserved 24 MAC High The 16 MSBs of the MAC address to receive during boot NO 26 MAC Med The 16 middle bits of the MAC address to receive during boot NO 28 MAC Low The 16 LSBs of the MAC address to receive during boot NO 30 Multi MAC High The 16 MSBs of the multicast MAC address to receive during boot NO 32 Multi MAC Med The 16 middle bits of the multicast MAC address to receive during boot NO 34 Multi MAC Low The 16 LSBs of the multicast MAC address to receive during boot NO 36 Source Port The source UDP port to accept boot packets from. NO 38 Dest Port The destination port to accept boot packets on. NO 40 Device ID 12 The first 2 bytes of the device ID. NO A value of 0 will accept packets from any UDP port This is typically a string value, and is sent in the Ethernet ready frame 42 Device ID 34 The second 2 bytes of the device ID. NO 44 Dest MAC High The 16 MSBs of the MAC destination address used NO 46 Dest MAC Med The 16 middle bits of the MAC destination address NO 48 Dest MAC Low The 16 LSBs of the MAC destination address NO 50 Lane Enable One bit per lane. • 0 = Lane disabled • 1 = Lane enabled for the Ethernet ready frame. Default is broadcast. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 199 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-19. Ethernet Boot Parameter Table (continued) CONFIGURED THROUGH BOOT CONFIGURATION PINS BYTE OFFSET NAME DESCRIPTION 52 SGMII Config Bits 0-3 are the config index, bit 4 set if direct config used, bit 5 set if NO no configuration done 54 SGMII Control The SGMII control register value NO 56 SGMII Adv Ability The SGMII ADV Ability register value NO 58 SGMII TX Cfg High The 16 MSBs of the SGMII Tx config register NO 60 SGMII TX Cfg Low The 16 LSBs of the SGMII Tx config register NO 62 SGMII RX Cfg High The 16 MSBs of the SGMII Rx config register NO 64 SGMII RX Cfg Low The 16 LSBs of the SGMII Rx config register NO 66 SGMII Aux Cfg High The 16 MSBs of the SGMII Aux config register NO 68 SGMII Aux Cfg Low The 16 LSBs of the SGMII Aux config register NO 70 PKT PLL Cfg MSW The packet subsystem PLL configuration, MSW NO 72 PKT PLL CFG LSW The packet subsystem PLL configuration, LSW NO 10.1.2.5.4 PCIe Boot Parameter Table Table 10-20. PCIe Boot Parameter Table BYTE OFFSET NAME DESCRIPTION 22 Options Bits 00 Mode • 0 = Host Mode (Direct boot mode) • 1 = Boot Table Boot Mode CONFIGURED THROUGH BOOT CONFIGURATION PINS NO Bits 01 Configuration of PCIe • 0 = PCIe is configured by RBL • 1 = PCIe is not configured by RBL Bit 03-02 Reserved Bits 04 Multiplier • 0 = SERDES PLL configuration is done based on SERDES register values • 1 = SERDES PLL configuration based on the reference clock values Bits 05-15 Reserved 24 Address Width PCI address width, can be 32 or 64 YES with in conjunction with BAR sizes 26 Link Rate SerDes frequency, in Mbps. Can be 2500 or 5000 NO 28 Reference clock Reference clock frequency, in units of 10 kHz. Value values are 10000 NO (100 MHz), 12500 (125 MHz), 15625 (156.25 MHz), 25000 (250 MHz) and 31250 (312.5 MHz). A value of 0 means that value is already in the SerDes cfg parameters and will not be computed by the boot ROM. 30 Window 1 Size Window 1 size. YES 32 Window 2 Size Window 2 size. YES 34 Window 3 Size Window 3 size. Valid only if address width is 32. YES 36 Window 4 Size Window 4 Size. Valid only if the address width is 32. YES 38 Vendor ID Vendor ID NO 40 Device ID Device ID NO 42 Class code Rev ID MSW Class code revision ID MSW NO 44 Class code Rev ID LSW Class code revision ID LSW NO 200 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-20. PCIe Boot Parameter Table (continued) BYTE OFFSET NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS 46 SerDes cfg msw PCIe SerDes config word, MSW NO 48 SerDes cfg lsw PCIe SerDes config word, LSW NO 50 SerDes lane 0 cfg msw SerDes lane config word, msw lane 0 NO 52 SerDes lane 0 cfg lsw NO 54 SerDes lane 1 cfg msw SerDes lane config word, msw, lane 1 NO 56 SerDes lane 1 cfg lsw SerDes lane config word, lsw, lane 1 NO 58 Time-out period (Secs) The time-out period. Values 0 disables the time-out. SerDes lane config word, lsw, lane 0 10.1.2.5.5 I2C Boot Parameter Table Table 10-21. I2C Boot Parameter Table CONFIGURED THROUGH BOOT CONFIGURATION PINS OFFS ET FIELD VALUE 22 Option Bits 02-00 Mode • 000 = Boot Parameter Table Mode • 001 = Boot Table Mode • 010 = Boot Config Mode • 011 = Load GP header format data • 100 = Slave Receive Boot Config 24 Boot Dev Addr The I2C device address to boot from YES 26 Boot Dev Addr Ext Extended boot device address YES 28 Broadcast Addr I2C address used to send data in the I2C master broadcast mode. NO 30 Local Address The I2C address of this device NO NO Bits 15-03 Reserved 2 34 Bus Frequency The desired I C data rate (kHz) NO 36 Next Dev Addr The next device address to boot (Used only if boot config option is selected) NO 38 Next Dev Addr Ext The extended next device address to boot (Used only if boot config option is selected) NO 40 Address Delay The number of CPU cycles to delay between writing the address to an I2C EEPROM and reading data. NO 10.1.2.5.6 SPI Boot Parameter Table Table 10-22. SPI Boot Parameter Table CONFIGURED THROUGH BOOT CONFIGURATION PINS BYTE OFFSET NAME DESCRIPTION 22 Options Bits 01 and 00 Modes • 00 = Load a boot parameter table from the SPI (Default mode) • 01 = Load boot records from the SPI (boot tables) • 10 = Load boot config records from the SPI (boot config tables) • 11 = Load GP header blob Bits 15- 02= Reserved NO 24 Address Width The number of bytes in the SPI device address. Can be 16 or 24 bit YES 26 NPin The operational mode, 4 or 5 pin YES 28 Chipsel The chip select used (valid in 4 pin mode only). Can be 0-3. YES 30 Mode Standard SPI mode (0-3) YES 32 C2Delay Setup time between chip assert and transaction NO Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 201 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-22. SPI Boot Parameter Table (continued) BYTE OFFSET NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS 34 Bus Freq, 100kHz The SPI bus frequency in kHz. NO 36 Read Addr MSW The first address to read from, MSW (valid for 24 bit address width only) YES 38 Read Addr LSW The first address to read from, LSW YES 40 Next Chip Select Next Chip Select to be used (Used only in boot Config mode) NO 42 Next Read Addr MSW The Next read address (used in boot config mode only) NO 44 Next Read Addr LSW NO The Next read address (used in boot config mode only) 10.1.2.5.7 HyperLink Boot Parameter Table Table 10-23. HyperLink Boot Parameter Table BYTE OFFSET NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS 12 Options Bits 00 Reserved NO Bits 01 Configuration of Hyperlink • 0 = HyperLink is configured by RBL • 1 = HyperLink is not configured by RBL Bits 15-02 = Reserved 14 Number of Lanes Number of Lanes to be configured NO 16 SerDes cfg msw PCIe SerDes config word, MSW NO 18 SerDes cfg lsw PCIe SerDes config word, LSW NO 20 SerDes CFG RX lane 0 cfg msw SerDes RX lane config word, msw lane 0 NO 22 SerDes CFG RXlane 0 cfg lsw SerDes RX lane config word, lsw, lane 0 NO 24 SerDes CFG TX lane 0 cfg msw SerDes TX lane config word, msw lane 0 NO 26 SerDes CFG TXlane 0 cfg lsw SerDes TX lane config word, lsw, lane 0 NO 28 SerDes CFG RX lane 1 cfg msw SerDes RX lane config word, msw lane 1 NO 30 SerDes CFG RXlane 1 cfg lsw SerDes RX lane config word, lsw, lane 1 NO 32 SerDes CFG TX lane 1 cfg msw SerDes TX lane config word, msw lane 1 NO 34 SerDes CFG TXlane 1 cfg lsw SerDes TX lane config word, lsw, lane 1 NO 36 SerDes CFG RX lane 2 cfg msw SerDes RX lane config word, msw lane 2 NO 38 SerDes CFG RXlane 2 cfg lsw SerDes RX lane config word, lsw, lane 2 NO 40 SerDes CFG TX lane 2 cfg msw SerDes TX lane config word, msw lane 2 NO 42 SerDes CFG TXlane 2 cfg lsw SerDes TX lane config word, lsw, lane 2 NO 44 SerDes CFG RX lane 3 cfg msw SerDes RX lane config word, msw lane 3 NO 46 SerDes CFG RXlane 3 cfg lsw SerDes RX lane config word, lsw, lane 3 NO 48 SerDes CFG TX lane 3 cfg msw SerDes TX lane config word, msw lane 3 NO 50 SerDes CFG TXlane 3 cfg lsw SerDes TX lane config word, lsw, lane 3 NO 10.1.2.5.8 UART Boot Parameter Table Table 10-24. UART Boot Parameter Table BYTE OFFSET NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS 22 Reserved None NA 202 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-24. UART Boot Parameter Table (continued) CONFIGURED THROUGH BOOT CONFIGURATION PINS BYTE OFFSET NAME DESCRIPTION 24 Data Format Bits 00 Data Format • 0 = Data Format is BLOB • 1 = Data Format is Boot Table Bits 15-01 Reserved NO 26 Protocol Bits 00 Protocol • 0 = Xmodem Protocol • 1 = Reserved Bits 15-01 Reserved NO 28 Initial NACK Count Number of NACK pings to be sent before giving up NO 30 Max Err Count Maximum number of consecutive receive errors acceptable. NO 32 NACK Time-out Time (ms) waiting for NACK/ACK. NO 34 Character Time-out Time Period between characters NO 36 nDatabits Number of bits supported for data. Only 8 bits is supported. NO 38 Parity Bits 01-00 Parity • 00 = No Parity • 01 = Odd parity • 10 = Even Parity Bits 15-02 Reserved NO 40 nStopBitsx2 Number of stop bits times two. Valid values are 2 (stop bits = 1), 3 (Stop Bits = 1.5), 4 (Stop Bits = 2) NO 42 Over sample factor The over sample factor. Only 13 and 16 are valid. NO 44 Flow Control Bits 00 Flow Control • 0 = No Flow Control • 1 = RTS_CTS flow control Bits 15-01 Reserved NO 46 Data Rate MSW Baud Rate, MSW NO 48 Data Rate LSW Baud Rate, LSW NO 10.1.2.5.9 NAND Boot Parameter Table Table 10-25. NAND Boot Parameter Table CONFIGURED THROUGH BOOT CONFIGURATION PINS BYTE OFFSET NAME DESCRIPTION 22 Options Bits 00 Geometry • 0 = Geometry is taken from this table • 1 = Geometry is queried from NAND device. Bits 01 Clear NAND • 0 = NAND Device is a non clear NAND and requires ECC • 1 = NAND is a clear NAND and doesn.t need ECC. Bits 15-02 Reserved NO 24 numColumnAddrBytes Number of bytes used to specify column address NO 26 numRowAddrBytes Number of bytes used to specify row address. NO 28 numofDataBytesperPage_msw Number of data bytes in each page, MSW NO 30 numofDataBytesperPage_lsw Number of data bytes in each page, LSW NO 32 numPagesperBlock Number of Pages per Block NO 34 busWidth EMIF bus width. Only 8 or 16 bits is supported. NO 36 numSpareBytesperPage Number of spare bytes allocated per page. NO 38 csel Chip Select number (valid chip selects are 2-5) YES (If ARM is the boot master only chip select 2 is supported) Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 203 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-25. NAND Boot Parameter Table (continued) BYTE OFFSET NAME DESCRIPTION CONFIGURED THROUGH BOOT CONFIGURATION PINS 40 First Block First block for RBL to try to read. YES 10.1.2.5.10 DDR3 Configuration Table The RBL also provides an option to configure the DDR table before loading the image into the external memory. More information on how to configure the DDR3, see the KeyStone Architecture DSP Bootloader User's Guide. The configuration table for DDR3 is shown in Table 10-26 Table 10-26. DDR3 Boot Parameter BYTE OFFSET NAME DESCRIPTION 0 Enable bitmap MSW Bits 31:0 of the PLL/EMIF enable bitmap. Bit 0 corresponds to the PLL config, Bit 1 to the SDRAM configuration register. There are 24 valid bits in this field (with the MSB corresponding to Rw/exc thresh). 4 Enable bitmap SLSW Bits 31:0 of the chip level register enable bit map. Bit 0 corresponds to chip level configuration register 0. 8 Enable bitmap LSW Bits 60:32 of the chip level register enable bit map. Bit 0 corresponds to chip level configuration register 32. 12 PLL Predivier PLL Predivision (1 = divide by 1, 2 = divide by 2, and so on) 16 PLL Multiplier PLL Multiplication 20 PLL Post Divider PLL Postdivision 24 sdRamConfig SDRAM Configuration Register 28 Refresh ctl SDRAM Refresh Control Register 32 Timing 1 SDRAM Timing 1 Register 36 Timing 2 SDRAM Timing 2 Register 40 Timing 3 SDRAM Timing 3 Register 44 Timing4 SDRAM Timing 4 Register 48 Pwr management Power Management Control Register 52 Vbus M cfg VBUS M Configuration 56 Vbus M cfg val 1 VBUS M Configuration Value 1 60 Vbus M cfg val 2 VBUSM Configuration Value 2 64 IO DFT Test I/O DFT test logic control 68 Perf ctl sel Performance Counter Master Region Select Register 72 Perf cnt Mst Reg Performance Count Master Region Select 76 Zq config SDRAM Output Impedance Calibration Configuration Register 80 Pri Class Svc Map Priority class Service Map 84 Mst Id class 1 Master ID class service map 1 88 Mst Id class 2 Master ID class service map 2 92 ECC ctrl ECC Control Register 96 ECC addr rng 1 ECC Address Range 1 Register 100 ECC addr rng 2 ECC Address Range 2 Register 104 Rw/exc thresh Read Write Execution Threshold Register 108 PHY PIR PHY PIR register (SLSW mask bit 0) 112 PHY PGCR0 PHY PGCR0 register (SLSW mask bit 1) 116 PHY PGCR1 PHY PGCR1 register (SLSW mask bit 2) 120 PHY PGCR2 PHY PGCR2 register (SLSW mask bit 3) 124 PHY PGSR0 PHY PGSR0 register (SLSW mask bit 4) 128 PHY PGSR1 PHY PGSR1 register (SLSW mask bit 5) 132 PHY PTR0 PHY PTR 0 register (SLSW mask bit 6) 136 PHY PTR1 PHY PTR 1 register (SLSW mask bit 7) 204 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-26. DDR3 Boot Parameter (continued) BYTE OFFSET NAME DESCRIPTION 140 PHY PTR2 PHY PTR 2 register (SLSW mask bit 8) 144 PHY PTR3 PHY PTR 3 register (SLSW mask bit 9) 148 PHY PTR4 PHY PTR 4 register (SLSW mask bit 10) 152 PHY DCR PHY DCR register (SLSW mask bit 11) 156 PHY DTPR0 PHY DTPR 0 register (SLSW mask bit 12) 160 PHY DTPR1 PHY DTPR 1 register (SLSW mask bit 13) 164 PHY DTPR2 PHY DTPR 2 register (SLSW mask bit 14) 168 PHY MR0 PHY MR 0 register (SLSW mask bit 15) 172 PHY MR1 PHY MR 1 register (SLSW mask bit 16) 176 PHY MR2 PHY MR 2 register (SLSW mask bit 17) 180 PHY DTCR PHY DTCR register (SLSW mask bit 18) 184 PHY DX0GCR PHY DX 0 GCR register (SLSW mask bit 19) 188 PHY DX1GCR PHY DX 1 GCR register (SLSW mask bit 20) 192 PHY DX2GCR PHY DX 2 GCR register (SLSW mask bit 21) 196 PHY DX3GCR PHY DX 3 GCR register (SLSW mask bit 22) 200 PHY DX4CGR PHY DX 4 GCR register (SLSW mask bit 23) 204 PHY DX5GCR PHY DX 5 GCR register (SLSW mask bit 24) 208 PHY DX6GCR PHY DX 6 GCR register (SLSW mask bit 25) 212 PHY DX7GCR PHY DX 7 GCR register (SLSW mask bit 26) 216 PHY DX8GCR PHY DX 8 GCR register (SLSW mask bit 27) 10.1.2.6 Second-Level Bootloaders Any of the boot modes can be used to download a second-level bootloader. A second-level bootloader allows for: • Any level of customization to current boot methods • Definition of a completely customized boot 10.1.3 SoC Security The TI SoC contains security architecture that allows the C66x CorePacs and ARM CorePac to perform secure accesses within the device. For more information, contact a TI sales office for additional information available with the purchase of a secure device. 10.1.4 System PLL Settings The PLL default settings are determined by the BOOTMODE[7:5] bits. Table 10-27 shows the settings for various input clock frequencies. This will set the PLL to the maximum clock setting for the device. CLK = CLKIN × ((PLLM+1) ÷ ((CLKOD+1) × (PLLD+1))) (1) Where OUTPUT_DIVIDE is the value of the field of SECCTL[22:19] The configuration for the PASS PLL is also shown. The PASS PLL is configured with these values only if the Ethernet boot mode is selected with the input clock set to match the main PLL clock (not the SGMII SerDes clock). See Table 10-11 for details on configuring Ethernet boot mode. The output from the PASS PLL goes through an on-chip divider to reduce the frequency before reaching the NETCP. The PASS PLL generates 1050 MHz, and after the chip divider (/3), applies 350 MHz to the NETCP. The Main PLL is controlled using a PLL controller and a chip-level MMR. The ARM CorePac PLL, DDR3A PLL, DDR3BPLL, and PASS PLL are controlled by chip level MMRs. For details on how to set up the PLL see Section 11.5. For details on the operation of the PLL controller module, see the KeyStone Architecture Phase Locked Loop (PLL) Controller User's Guide. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 205 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-27. System PLL Configuration 800-MHz DEVICE 1000-MHz DEVICE PA = 350 MHz (2) BOOTMODE [7:5] INPUT CLOCK FREQ (MHz) (1) 1200-MHz DEVICE PLLD PLLM DSP ƒ PLLD PLLM DSP ƒ PLLD PLLM DSP ƒ PLLD PLLM DSP ƒ (3) 0b000 50.00 0 31 800 0 39 1000 0 47 1200 0 41 1050 0b001 66.67 0 23 800.04 0 29 1000.05 0 35 1200.06 1 62 1050.053 0b010 80.00 0 19 800 0 24 1000 0 29 1200 3 104 1050 0b011 100.00 0 15 800 0 19 1000 0 23 1200 0 20 1050 0b100 156.25 3 40 800.78 4 63 1000 2 45 1197.92 24 335 1050 0b101 250.00 4 31 800 0 7 1000 4 47 1200 41 1050 0b110 312.50 7 40 800.78 4 31 1000 2 22 1197.92 24 167 1050 0b111 122.88 0 12 798.72 3 64 999.989 0 19 1228.80 11 204 1049.6 4 (1) The CLKOD reset value = 1, and the value of 1 is used for all calculations in this table (based on Equation 1). (2) (3) The PASS PLL generates 1050 MHz and is internally divided by 3 to feed 350 MHz to the packet accelerator. ƒ represents frequency in MHz. 10.1.4.1 ARM CorePac System PLL Settings The PLL default settings are determined by the BOOTMODE[11:9] bits. Table 10-28 shows settings for various input clock frequencies. This will set the PLL to the maximum clock setting for the device. CLK = CLKIN × ((PLLM+1) ÷ ((CLKOD+1) × (PLLD+1))) (2) The ARM CorePac PLL is controlled using a PLL controller and a chip-level MMR. For details on how to set up the PLL see Section 11.5. For details on the operation of the PLL controller module, see the KeyStone Architecture Phase Locked Loop (PLL) Controller User's Guide. Table 10-28. ARM PLL Configuration BOOTMODE [11:9] INPUT CLOCK FREQ (MHz) (1) 800-MHz DEVICE 1000-MHz DEVICE PLLD PLLM ARM ƒ PLLD PLLM ARM ƒ PLLD PLLM ARM ƒ PLLD PLLM ARM ƒ (2) 0b000 50.00 0 31 800 0 39 1000 0 47 1200 0 55 1400 0b001 66.67 0 23 800.04 0 29 1000.05 0 35 1200.06 0 41 1400.07 0b010 80.00 0 19 800 0 24 1000 0 29 1200 0 34 1400 0b011 100.00 0 15 800 0 19 1000 0 23 1200 0 27 1400 0b100 156.25 3 40 800.78 4 63 1000 2 45 1197.92 0 17 1406.25 0b101 250.00 4 31 800 7 1000 4 47 1200 55 1400 0b110 312.50 7 40 800.78 4 31 1000 2 22 1197.92 0 8 1406.25 0b111 122.88 0 12 798.72 3 64 999.40 0 19 1200.80 0 22 1413.12 0 1200-MHz DEVICE 1400-MHz DEVICE 4 (1) The CLKOD reset value = 1, and the value of 1 is used for all calculations in this table (based on Equation 2). (2) ƒ represents frequency in MHz. 10.2 Device Configuration Certain device configurations like boot mode and endianess are selected at device power-on reset. The status of the peripherals (enabled/disabled) is determined after device power-on reset. By default, the peripherals on the device are disabled and need to be enabled by software before being used. 206 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 10.2.1 Device Configuration at Device Reset The logic level present on each device configuration pin is latched at power-on reset to determine the device configuration. The logic level on the device configuration pins can be set by using external pullup/pulldown resistors or by using some control device (for example, FPGA/CPLD) to intelligently drive these pins. When using a control device, care should be taken to ensure there is no contention on the lines when the device is out of reset. The device configuration pins are sampled during power-on reset and are driven after the reset is removed. To avoid contention, the control device must stop driving the device configuration pins of the SoC. Table 10-29 describes the device configuration pins. NOTE If a configuration pin must be routed out from the device and it is not driven (Hi-Z state), the internal pullup/pulldown (IPU/IPD) resistor should not be relied upon. TI recommends the use of an external pullup/pulldown resistor. For more detailed information on pullup/pulldown resistors and situations in which external pullup/pulldown resistors are required, see Section 4.4. Table 10-29. Device Configuration Pins (1) CONFIGURATION PIN PIN NO. IPD/IPU LENDIAN (1) (2) F29 IPU BOOTMODE[15:0] (1) (2) B30, D29, A35, B29, IPD E29, D30, C30, A30, G30, F31, E30, F30, A31, F24, E24, D24 Method of boot • See Section 10.1.2 for more details. • See the KeyStone Architecture DSP Bootloader User's Guide for detailed information on boot configuration. AVSIFSEL[1:0] (1) (2) M1, M2 IPD AVS interface selection • 00 = AVS 4-pin 6-bit Dual-Phase VCNTL[5:2] (Default) • 01 = AVS 4-pin 4-bit Single-Phase VCNTL[5:2] • 10 = AVS 6-pin 6-bit Single-Phase VCNTL[5:0] • 11 = I2C MAINPLLODSEL (1) (2) E32 IPD Main PLL Output divider select • 0 = Main PLL output divider needs to be set to 2 by BOOTROM • 1 = Reserved ARMAVSSHARED (1) G24 IPD ARM AVS Shared with the rest of SOC AVS • 0 = Reserved • 1 = ARM Core voltage and rest of SoC core voltage shared BOOTMODE_RSVD (1) B31 IPD Boot mode reserved. Pulldown resistor required on pin. A36 IPD Control ARM remapping of DDR3A address space in the lower 4GB (32b space) Mode select • 0 = DDR3A memory is accessible from ARM at 0x08 0000 00000x09 FFFF FFFF. • 1 = DDR3A memory is accessible from ARM at 0x00 8000 00000x00 FFFF FFFF with 0x00 8000 0000-0x00 FFFF FFFF aliased at 0x08 0000 0000-0x08 7FFF FFFF. DDR3A_MAP_EN (1) (2) (1) DESCRIPTION Device endian mode (LENDIAN) • 0 = Device operates in big endian mode • 1 = Device operates in little endian mode Internal 100-μA pulldown or pullup is provided for this terminal. In most systems, a 1-kΩ resistor can be used to oppose the IPD/IPU. For more detailed information on pulldown/pullup resistors and situations in which external pulldown/pullup resistors are required, see Section 4.4. These signal names are the secondary functions of these pins. 10.2.2 Peripheral Selection After Device Reset Several of the peripherals on the 66AK2Hxx are controlled by the Power Sleep Controller (PSC). By default, the PCIe, SRIO, and HyperLink are held in reset and clock-gated. The memories in these modules are also in a low-leakage sleep mode. Software is required to turn these memories on. Then, the software enables the modules (turns on clocks and deasserts reset) before these modules can be used. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 207 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com If one of the above modules is used in the selected ROM boot mode, the ROM code automatically enables the module. All other modules come up enabled by default and there is no special software sequence to enable. For more detailed information on the PSC usage, see the KeyStone Architecture Power Sleep Controller (PSC) User's Guide. 10.2.3 Device State Control Registers The 66AK2Hxx device has a set of registers that are used to control the status of its peripherals. These registers are shown in Table 10-30. Table 10-30. Device State Control Registers ADDRESS START ADDRESS END SIZE ACRONYM 0x02620000 0x02620007 8B Reserved 0x02620008 0x02620017 16B Reserved 0x02620018 0x0262001B 4B JTAGID 0x0262001C 0x0262001F 4B Reserved 0x02620020 0x02620023 4B DEVSTAT 0x02620024 0x02620037 20B Reserved 0x02620038 0x0262003B 4B KICK0 0x0262003C 0x0262003F 4B KICK1 0x02620040 0x02620043 4B DSP_BOOT_ADDR0 The boot address for C66x CorePac0. See Section 10.2.3.5 0x02620044 0x02620047 4B DSP_BOOT_ADDR1 The boot address for C66x CorePac1. See Section 10.2.3.5 0x02620048 0x0262004B 4B DSP_BOOT_ADDR2 The boot address for C66x CorePac2. See Section 10.2.3.5 0x0262004C 0x0262004F 4B DSP_BOOT_ADDR3 The boot address for C66x CorePac3. See Section 10.2.3.5 0x02620050 0x02620053 4B DSP_BOOT_ADDR4 The boot address for C66x CorePac4 (66AK2H14/12 only). See Section 10.2.3.5 0x02620054 0x02620057 4B DSP_BOOT_ADDR5 The boot address for C66x CorePac5 (66AK2H14/12 only). See Section 10.2.3.5 0x02620058 0x0262005B 4B DSP_BOOT_ADDR6 The boot address for C66x CorePac6 (66AK2H14/12 only). See Section 10.2.3.5 0x0262005C 0x0262005F 4B DSP_BOOT_ADDR7 The boot address for C66x CorePac7 (66AK2H14/12 only). See Section 10.2.3.5 0x02620060 0x026200DF 128B Reserved 0x026200E0 0x0262010F 48B Reserved 0x02620110 0x02620117 8B MACID 0x02620118 0x0262012F 24B Reserved 0x02620130 0x02620133 4B LRSTNMIPINSTAT_CLR See Section 10.2.3.7 0x02620134 0x02620137 4B RESET_STAT_CLR See Section 10.2.3.9 0x02620138 0x0262013B 4B Reserved 0x0262013C 0x0262013F 4B BOOTCOMPLETE 0x02620140 0x02620143 4B Reserved 0x02620144 0x02620147 4B RESET_STAT See Section 10.2.3.8 0x02620148 0x0262014B 4B LRSTNMIPINSTAT See Section 10.2.3.6 0x0262014C 0x0262014F 4B DEVCFG See Section 10.2.3.2 0x02620150 0x02620153 4B PWRSTATECTL See Section 10.2.3.11 208 Device Boot and Configuration DESCRIPTION See Section 10.2.3.3 See Section 10.2.3.1 See Section 10.2.3.4 See Section 11.17 See Section 10.2.3.10 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-30. Device State Control Registers (continued) ADDRESS START ADDRESS END SIZE ACRONYM 0x02620154 0x02620157 4B Reserved 0x02620158 0x0262015B 4B Reserved 0x0262015C 0x0262015F 4B Reserved 0x02620160 0x02620160 4B Reserved 0x02620164 0x02620167 4B Reserved 0x02620168 0x0262016B 4B Reserved 0x0262016C 0x0262017F 20B Reserved 0x02620180 0x02620183 4B SmartReflex Class0 0x02620184 0x0262018F 12B Reserved 0x02620190 0x02620193 4B Reserved 0x02620194 0x02620197 4B Reserved 0x02620198 0x0262019B 4B Reserved 0x0262019C 0x0262019F 4B Reserved 0x026201A0 0x026201A3 4B Reserved 0x026201A4 0x026201A7 4B Reserved 0x026201A8 0x026201AB 4B Reserved 0x026201AC 0x026201AF 4B Reserved 0x026201B0 0x026201B3 4B Reserved 0x026201B4 0x026201B7 4B Reserved 0x026201B8 0x026201BB 4B Reserved 0x026201BC 0x026201BF 4B Reserved 0x026201C0 0x026201C3 4B Reserved 0x026201C4 0x026201C7 4B Reserved 0x026201C8 0x026201CB 4B Reserved 0x026201CC 0x026201CF 4B Reserved 0x026201D0 0x026201FF 48B Reserved 0x02620200 0x02620203 4B NMIGR0 0x02620204 0x02620207 4B NMIGR1 0x02620208 0x0262020B 4B NMIGR2 0x0262020C 0x0262020F 4B NMIGR3 0x02620210 0x02620213 4B NMIGR4 (66AK2H14/12 only) 0x02620214 0x02620217 4B NMIGR5 (66AK2H14/12 only) 0x02620218 0x0262021B 4B NMIGR6 (66AK2H14/12 only) 0x0262021C 0x0262021F 4B NMIGR7 (66AK2H14/12 only) 0x02620220 0x0262023F 32B Reserved 0x02620240 0x02620243 4B IPCGR0 0x02620244 0x02620247 4B IPCGR1 0x02620248 0x0262024B 4B IPCGR2 0x0262024C 0x0262024F 4B IPCGR3 0x02620250 0x02620253 4B IPCGR4 0x02620254 0x02620257 4B IPCGR5 0x02620258 0x0262025B 4B IPCGR6 0x0262025C 0x0262025F 4B IPCGR7 0x02620260 0x02620263 4B IPCGR8 0x02620264 0x02620267 4B IPCGR9 0x02620268 0x0262026B 4B IPCGR10 0x0262026C 0x0262026F 4B IPCGR11 DESCRIPTION See Section 11.2.4 See Section 10.2.3.12 See Section 10.2.3.13 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 209 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-30. Device State Control Registers (continued) ADDRESS START ADDRESS END SIZE ACRONYM 0x02620270 0x0262027B 12B Reserved 0x0262027C 0x0262027F 4B IPCGRH See Section 10.2.3.15 0x02620280 0x02620283 4B IPCAR0 See Section 10.2.3.14 0x02620284 0x02620287 4B IPCAR1 0x02620288 0x0262028B 4B IPCAR2 0x0262028C 0x0262028F 4B IPCAR3 0x02620290 0x02620293 4B IPCAR4 0x02620294 0x02620297 4B IPCAR5 0x02620298 0x0262029B 4B IPCAR6 0x0262029C 0x0262029F 4B IPCAR7 0x026202A0 0x026202A3 4B IPCAR8 0x026202A4 0x026202A7 4B IPCAR9 0x026202A8 0x026202AB 4B IPCAR10 0x026202AC 0x026202AF 4B IPCAR11 0x026202B0 0x026202BB 12B Reserved 0x026202BC 0x026202BF 4B IPCARH 0x026202C0 0x026202FF 64B Reserved 0x02620300 0x02620303 4B TINPSEL See Section 10.2.3.17 0x02620304 0x02620307 4B TOUTPSEL See Section 10.2.3.18 0x02620308 0x0262030B 4B RSTMUX0 See Section 10.2.3.19 0x0262030C 0x0262030F 4B RSTMUX1 0x02620310 0x02620313 4B RSTMUX2 0x02620314 0x02620317 4B RSTMUX3 0x02620318 0x0262031B 4B RSTMUX4 0x0262031C 0x0262031F 4B RSTMUX5 0x02620320 0x02620323 4B RSTMUX6 0x02620324 0x02620327 4B RSTMUX7 0x02620328 0x0262032B 4B RSTMUX8 0x0262032C 0x0262032F 4B RSTMUX9 0x02620330 0x02620333 4B RSTMUX10 0x02620334 0x02620337 4B RSTMUX11 0x02620338 0x0262034F 4B Reserved 0x02620350 0x02620353 4B MAINPLLCTL0 0x02620354 0x02620357 4B MAINPLLCTL1 0x02620358 0x0262035B 4B PASSPLLCTL0 0x0262035C 0x0262035F 4B PASSPLLCTL1 0x02620360 0x02620363 4B DDR3APLLCTL0 0x02620364 0x02620367 4B DDR3APLLCTL1 0x02620368 0x0262036B 4B DDR3BPLLCTL0 0x0262036C 0x0262036F 4B DDR3BPLLCTL1 0x02620370 0x02620373 4B ARMPLLCTL0 0x02620374 0x02620377 4B ARMPLLCTL1 0x02620378 0x0262039B 132B Reserved 0x0262039C 0x0262039F 4B Reserved 0x02620400 0x02620403 4B ARMENDIAN_CFG0_0 0x02620404 0x02620407 4B ARMENDIAN_CFG0_1 0x02620408 0x0262040B 4B ARMENDIAN_CFG0_2 210 Device Boot and Configuration DESCRIPTION See Section 10.2.3.16 See Section 11.5 See Section 11.7 See Section 11.6 See Section 11.6 See Section 10.1.4.1 See Section 10.2.3.21 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-30. Device State Control Registers (continued) ADDRESS START ADDRESS END SIZE ACRONYM 0x0262040C 0x026205FF 62B Reserved 0x02620600 0x026206FF 256B Reserved 0x02620700 0x02620703 4B CHIP_MISC_CTL0 0x02620704 0x0262070F 12B Reserved 0x02620710 0x02620713 4B SYSENDSTAT 0x02620714 0x02620717 4B Reserved 0x02620718 0x0262071B 4B Reserved 0x0262071C 0x0262071F 4B Reserved 0x02620720 0x0262072F 16B Reserved 0x02620730 0x02620733 4B SYNECLK_PINCTL 0x02620734 0x02620737 4B Reserved 0x02620738 0x0262074F 24B USB_PHY_CTL 0x02620750 0x026207FF 176B Reserved 0x02620800 0x02620C7B 1148B Reserved 0x02620C7C 0x02620C7F 4B CHIP_MISC_CTL1 0x02620C80 0x02620C97 24B Reserved 0x02620C90 (silicon revisions 2.0, 3.0, and 3.1) 0x02620C93 (silicon revisions 2.0, 3.0, and 3.1) 4B DEVSPEED See Section 10.2.3.20 0x02620C98 (silicon revision 1.1, 1.0) 0x02620C9B (silicon revision 1.1, 1.0) 4B DEVSPEED See Section 10.2.3.20 0x02620C9C 0x02620FFF 868B Reserved DESCRIPTION See Section 10.2.3.24 See Section 10.2.3.26 See Section 10.2.3.27 See Section 10.2.3.28 See Section 10.2.3.25 10.2.3.1 Device Status (DEVSTAT) Register The Device Status register depicts device configuration selected upon a power-on reset by the POR or RESETFULL pin. Once set, these bits remain set until a power-on reset. The Device Status register is shown in Figure 10-13 and described in Table 10-31. Figure 10-13. Device Status Register 31 15 30 29 21 20 19 Reserved DDR3A_ MAP_EN Reserved ARMAVS SHARED Rsvd MAINPLL ODSEL AVSIFSEL R-0000 0000 0000 00 R-x R-x R/W-x R-x R/W-x R/W-xx 5 4 3 14 13 28 12 27 26 11 10 25 24 9 23 8 7 22 6 18 2 17 16 BOOT MODE R/W-x xxxx xxxx xxxx xxx 1 BOOTMODE 0 LENDIAN R/W-x xxxx xxxx xxxx xxx R-x (1) Legend: R = Read only; RW = Read/Write; -n = value after reset (1) x indicates the bootstrap value latched via the external pin Table 10-31. Device Status Register Field Descriptions Bit Field Description 31-26 Reserved Reserved. Read only, writes have no effect. 25 DDR3A_MAP_EN DDR3A mapping enable • 0 = DDR3A memory is accessible from ARM at 0x8:0000_0000-0x9:FFFF_FFFF. • 1 = DDR3A memory is accessible in 32b space from ARM, that is, at 0x0:8000_0000-0x0:FFFF_FFFF. DDR3A is also accessible at 0x8:0000_0000-0x9:FFFF_FFFF, with the space 0x0:8000_00000x0:FFFF_FFFF address aliased at 0x8:0000_0000-0x8:7FFF_FFFF. 24-22 Reserved Reserved Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 211 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-31. Device Status Register Field Descriptions (continued) Bit Field Description 21 ARMAVSSHARED ARM AVS Shared with the rest of SOC AVS • 0 = Reserved • 1 = ARM Core voltage and rest of SoC core voltage share 20 Reserved Reserved 19 MAINPLLODSEL Main PLL Output divider select • 0 = Main PLL output divider needs to be set to 2 by BOOTROM • 1 = Reserved 18-17 AVSIFSEL AVS interface selection • 00 = AVS 4pin 6bit Dual-Phase VCNTL[5:2] (Default) • 01 = AVS 4pin 4bit Single-Phase VCNTL[5:2] • 10 = AVS 6pin 6bit Single-Phase VCNTL[5:0] • 11 = I2C 16-1 BOOTMODE Determines the boot mode configured for the device. For more information on boot mode, see Section 10.1.2 and the KeyStone Architecture DSP Bootloader User's Guide. 0 LENDIAN Device endian mode (LENDIAN) — shows the status of whether the system is operating in big endian mode or little endian mode (default). • 0 = System is operating in big endian mode • 1 = System is operating in little endian mode (default) 10.2.3.2 Device Configuration Register The Device Configuration Register is one-time writeable through software. The register is reset on all hard resets and is locked after the first write. The Device Configuration Register is shown in Figure 10-14 and described in Table 10-32. Figure 10-14. Device Configuration Register (DEVCFG) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Reserved PCIESSMODE SYSCLK OUTEN R-0 R/W-00 R/W-1 Legend: R = Read only; RW = Read/Write; -n = value after reset Table 10-32. Device Configuration Register Field Descriptions Bit Field Description 31-3 Reserved Reserved. Read only, writes have no effect. 2-1 PCIESSMODE Device Type Input of PCIeSS • 00 = Endpoint • 01 = Legacy Endpoint • 10 = Rootcomplex • 11 = Reserved 0 SYSCLKOUTEN SYSCLKOUT enable • 0 = No clock output • 1 = Clock output enabled (default) 10.2.3.3 JTAG ID (JTAGID) Register Description The JTAG ID register is a read-only register that identifies to the customer the JTAG/Device ID. For the device, the JTAG ID register resides at address location 0x02620018. The JTAG ID register is shown in Figure 10-15 and described in Table 10-33. 212 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Figure 10-15. JTAG ID (JTAGID) Register 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 VARIANT PART NUMBER MANUFACTURER LSB R-xxxx R-1011 1001 1000 0001 R-0000 0010 111 R-1 LEGEND: R/W = Read/Write; R = Read only; -n = value after reset Table 10-33. JTAG ID Register Field Descriptions Bit Field Value Description 31-28 VARIANT xxxx Variant value 27-12 PART NUMBER 1011 1001 1000 0001 Part Number for boundary scan 11-1 MANUFACTURER 0000 0010 111 Manufacturer 0 LSB 1 This bit is read as a 1 NOTE The value of the VARIANT and PART NUMBER fields depends on the silicon revision being used. See the Silicon Errata for details. 10.2.3.4 Kicker Mechanism (KICK0 and KICK1) Register The Bootcfg module contains a kicker mechanism to prevent spurious writes from changing any of the Bootcfg MMR (memory mapped registers) values. When the kicker is locked (which it is initially after power on reset), none of the Bootcfg MMRs are writable (they are only readable). This mechanism requires an MMR write to each of the KICK0 and KICK1 registers with exact data values before the kicker lock mechanism is unlocked. See Table 10-30 for the address location. Once released, all the Bootcfg MMRs having write permissions are writable (the read only MMRs are still read only). The KICK0 data is 0x83e70b13. The KICK1 data is 0x95a4f1e0. Writing any other data value to either of these kick MMRs locks the kicker mechanism and blocks writes to Bootcfg MMRs. To ensure protection to all Bootcfg MMRs, software must always relock the kicker mechanism after completing the MMR writes. 10.2.3.5 DSP Boot Address Register (DSP_BOOT_ADDRn) The DSP_BOOT_ADDRn register stores the initial boot fetch address of CorePac_n (n = core number). The fetch address is the public ROM base address (for any boot mode) by default. DSP_BOOT_ADDRn register access should be permitted to any master or emulator when the device is non-secure. CorePac boots from that address when a reset is performed. The DSP_BOOT_ADDRn register is shown in Table 10-34 and described in Table 10-35. Table 10-34. DSP BOOT Address Register (DSP_BOOT_ADDRn) 3 1 10 DSP_BOOT_ADDR RW-0010000010110000000000 9 0 Reserved R-0 Legend: R = Read only; -n = value after reset Table 10-35. DSP BOOT Address Register (DSP_BOOT_ADDRn) Field Descriptions Bit Field 31-10 DSP_BOOT_ADDR 9-0 Reserved Description Boot address of CorePac. CorePac boots from that address when a reset is performed. The reset value is 22 MSBs of ROM base address = 0x20B00000. Reserved 10.2.3.6 LRESETNMI PIN Status (LRSTNMIPINSTAT) Register The LRSTNMIPINSTAT register latches the status of LRESET and NMI. The LRESETNMI PIN Status register is shown in Figure 10-16 and described in Table 10-36. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 213 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Figure 10-16. LRESETNMI PIN Status Register (LRSTNMIPINSTAT) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Reserved 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 NMI7 NMI6 NMI5 NMI4 NMI3 NMI2 NMI1 NMI0 LR7 LR6 LR5 LR4 LR3 LR2 LR1 LR0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 Legend: R = Read only; -n = value after reset Table 10-36. LRESETNMI PIN Status Register Field Descriptions Bit Field Description 31-16 Reserved Reserved 15 NMI7 C66x CorePac7 in NMI (66AK2H14/12 only) 14 NMI6 C66x CorePac6 in NMI (66AK2H14/12 only) 13 NMI5 C66x CorePac5 in NMI (66AK2H14/12 only) 12 NMI4 C66x CorePac4 in NMI (66AK2H14/12 only) 11 NMI3 C66x CorePac3 in NMI 10 NMI2 C66x CorePac2 in NMI 9 NMI1 C66x CorePac1 in NMI 8 NMI0 C66x CorePac0 in NMI 7 LR7 C66x CorePac7 in Local Reset (66AK2H14/12 only) 6 LR6 C66x CorePac6 in Local Reset (66AK2H14/12 only) 5 LR5 C66x CorePac5 in Local Reset (66AK2H14/12 only) 4 LR4 C66x CorePac4 in Local Reset (66AK2H14/12 only) 3 LR3 C66x CorePac3 in Local Reset 2 LR2 C66x CorePac2 in Local Reset 1 LR1 C66x CorePac1 in Local Reset 0 LR0 C66x CorePac0 in Local Reset 10.2.3.7 LRESETNMI PIN Status Clear (LRSTNMIPINSTAT_CLR) Register The LRSTNMIPINSTAT_CLR register clears the status of LRESET and NMI. The LRESETNMI PIN Status Clear register is shown in Figure 10-17 and described in Table 10-37. Figure 10-17. LRESETNMI PIN Status Clear Register (LRSTNMIPINSTAT_CLR) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 Reserved 16 15 14 13 12 11 10 9 8 7 NMI7 NMI6 NMI5 NMI4 NMI3 NMI2 NMI1 NMI0 LR7 R-0 6 5 4 3 2 1 0 LR6 LR5 LR4 LR3 LR2 LR1 LR0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 WC-0 Legend: R = Read only; -n = value after reset; WC = Write 1 to Clear Table 10-37. LRESETNMI PIN Status Clear Register Field Descriptions Bit Field Description 31-16 Reserved Reserved 15 NMI7 C66x CorePac7 in NMI Clear (66AK2H14/12 only) 14 NM6 C66x CorePac6 in NMI Clear (66AK2H14/12 only) 13 NMI5 C66x CorePac5 in NMI Clear (66AK2H14/12 only) 12 NMI4 C66x CorePac4 in NMI Clear (66AK2H14/12 only) 11 NMI3 C66x CorePac3 in NMI Clear 10 NMI2 C66x CorePac2 in NMI Clear 9 NMI1 C66x CorePac1 in NMI Clear 8 NMI0 C66x CorePac0 in NMI Clear 7 LR7 C66x CorePac7 in Local Reset Clear (66AK2H14/12 only) 6 LR6 C66x CorePac6 in Local Reset Clear (66AK2H14/12 only) 5 LR5 C66x CorePac5 in Local Reset Clear (66AK2H14/12 only) 214 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 10-37. LRESETNMI PIN Status Clear Register Field Descriptions (continued) Bit Field Description 4 LR4 C66x CorePac4 in Local Reset Clear (66AK2H14/12 only) 3 LR3 C66x CorePac3 in Local Reset Clear 2 LR2 C66x CorePac2 in Local Reset Clear 1 LR1 C66x CorePac1 in Local Reset Clear 0 LR0 C66x CorePac0 in Local Reset Clear 10.2.3.8 Reset Status (RESET_STAT) Register The Reset Status register (RESET_STAT) captures the status of local reset (LRx) for each of the cores and also the global device reset (GR). Software can use this information to take different device initialization steps. • In case of local reset: The LRx bits are written as 1 and the GR bit is written as 0 only when the C66x CorePac receives a local reset without receiving a global reset. • In case of global reset: The LRx bits are written as 0 and the GR bit is written as 1 only when a global reset is asserted. The Reset Status register is shown in Figure 10-18 and described in Table 10-38. Figure 10-18. Reset Status Register (RESET_STAT) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 GR Reserved R-1 R-000 0000 0000 0000 0000 0000 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 LR7 LR6 LR5 LR4 LR3 LR2 LR1 LR0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 Legend: R = Read only; -n = value after reset Table 10-38. Reset Status Register Field Descriptions Bit 31 30-8 Field Description GR Global reset status • 0 = Device has not received a global reset. • 1 = Device received a global reset. Reserved Reserved. 7 LR7 C66x CorePac7 reset status (66AK2H14/12 only) • 0 = C66x CorePac7 has not received a local reset. • 1 = C66x CorePac7 received a local reset. 6 LR6 C66x CorePac6 reset status (66AK2H14/12 only) • 0 = C66x CorePac6 has not received a local reset. • 1 = C66x CorePac6 received a local reset. 5 LR5 C66x CorePac5 reset status (66AK2H14/12 only) • 0 = C66x CorePac5 has not received a local reset. • 1 = C66x CorePac5 received a local reset. 4 LR4 C66x CorePac4 reset status (66AK2H14/12 only) • 0 = C66x CorePac4 has not received a local reset. • 1 = C66x CorePac4received a local reset. 3 LR3 C66x CorePac3 reset status • 0 = C66x CorePac3 has not received a local reset. • 1 = C66x CorePac3 received a local reset. 2 LR2 C66x CorePac2 reset status • 0 = C66x CorePac2 has not received a local reset. • 1 = C66x CorePac2 received a local reset. 1 LR1 C66x CorePac1 reset status • 0 = C66x CorePac1 has not received a local reset. • 1 = C66x CorePac1 received a local reset. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 215 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 10-38. Reset Status Register Field Descriptions (continued) Bit Field 0 Description LR0 C66x CorePac0 reset status • 0 = C66x CorePac0 has not received a local reset. • 1 = C66x CorePac0 received a local reset. 10.2.3.9 Reset Status Clear (RESET_STAT_CLR) Register The RESET_STAT bits can be cleared by writing 1 to the corresponding bit in the RESET_STAT_CLR register. The Reset Status Clear register is shown in Figure 10-19 and described in Table 10-39. Figure 10-19. Reset Status Clear Register (RESET_STAT_CLR) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 GR Reserved RW-0 R-000 0000 0000 0000 0000 0000 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 LR7 LR6 LR5 LR4 LR3 LR2 LR1 LR0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 Legend: R = Read only; RW = Read/Write; -n = value after reset Table 10-39. Reset Status Clear Register Field Descriptions Bit Field Description 31 GR Global reset clear bit • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the GR bit clears the corresponding bit in the RESET_STAT register. 30-8 Reserved Reserved. 7 LR7 C66x CorePac7 reset clear bit (66AK2H14/12 only) • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR7 bit clears the corresponding bit in the RESET_STAT register. 6 LR6 C66x CorePac6 reset clear bit (66AK2H14/12 only) • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR6 bit clears the corresponding bit in the RESET_STAT register. 5 LR5 C66x CorePac5 reset clear bit (66AK2H14/12 only) • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR5 bit clears the corresponding bit in the RESET_STAT register. 4 LR4 C66x CorePac4 reset clear bit (66AK2H14/12 only) • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR4 bit clears the corresponding bit in the RESET_STAT register. 3 LR3 C66x CorePac3 reset clear bit • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR3 bit clears the corresponding bit in the RESET_STAT register. 2 LR2 C66x CorePac2 reset clear bit • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR2 bit clears the corresponding bit in the RESET_STAT register. 1 LR1 C66x CorePac1 reset clear bit • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR1 bit clears the corresponding bit in the RESET_STAT register. 0 LR0 C66x CorePac0 reset clear bit • 0 = Writing a 0 has no effect. • 1 = Writing a 1 to the LR0 bit clears the corresponding bit in the RESET_STAT register. 10.2.3.10 Boot Complete (BOOTCOMPLETE) Register The BOOTCOMPLETE register controls the BOOTCOMPLETE pin status to indicate the completion of the ROM booting process. The Boot Complete register is shown in Figure 10-20 and described in Table 1040. 216 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Figure 10-20. Boot Complete Register (BOOTCOMPLETE) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 Reserved R,-0000 0000 0000 0000 0000 11 10 9 BC11 BC10 BC9 8 7 6 5 4 3 2 1 0 BC8 BC7 BC6 BC5 BC4 BC3 BC BC1 BC0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 LEGEND: R/W = Read/Write; R = Read only; -n = value after reset Table 10-40. Boot Complete Register Field Descriptions Bit Field Description 31-12 Reserved Reserved. 11 BC11 ARM CorePac 3 boot status (66AK2H14/12 only) • 0 = ARM CorePac 3 boot NOT complete • 1 = ARM CorePac 3 boot complete 10 BC10 ARM CorePac 2 boot status (66AK2H14/12 only) • 0 = ARM CorePac 2 boot NOT complete • 1 = ARM CorePac 2 boot complete 9 BC9 ARM CorePac 1 boot status • 0 = ARM CorePac 1 boot NOT complete • 1 = ARM CorePac 1 boot complete 8 BC8 ARM CorePac 0 boot status • 0 = ARM CorePac 0 boot NOT complete • 1 = ARM CorePac 0 boot complete 7 BC7 C66x CorePac 7 boot status (66AK2H14/12 only) • 0 = C66x CorePac 7 boot NOT complete • 1 = C66x CorePac 7 boot complete 6 BC6 C66x CorePac 6 boot status (66AK2H14/12 only) • 0 = C66x CorePac 6 boot NOT complete • 1 = C66x CorePac 6 boot complete 5 BC5 C66x CorePac 5 boot status (66AK2H14/12 only) • 0 = C66x CorePac 5 boot NOT complete • 1 = C66x CorePac 5 boot complete 4 BC4 C66x CorePac 4 boot status (66AK2H14/12 only) • 0 = C66x CorePac 4 boot NOT complete • 1 = C66x CorePac 4 boot complete 3 BC3 C66x CorePac 3 boot status • 0 = C66x CorePac 3 boot NOT complete • 1 = C66x CorePac 3 boot complete 2 BC2 C66x CorePac2 boot status • 0 = C66x CorePac 2 boot NOT complete • 1 = C66x CorePac 2 boot complete 1 BC1 C66x CorePac1 boot status • 0 = C66x CorePac 1 boot NOT complete • 1 = C66x CorePac 1 boot complete 0 BC0 C66x CorePac 0 boot status • 0 = C66x CorePac 0 boot NOT complete • 1 = C66x CorePac 0 boot complete The BCx bit indicates the boot complete status of the corresponding C66x CorePac. All BCx bits are sticky bits — that is, they can be set only once by the software after device reset and they will be cleared to 0 on all device resets (warm reset and power-on reset). Boot ROM code is implemented such that each C66x CorePac sets its corresponding BCx bit immediately before branching to the predefined location in memory. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Device Boot and Configuration 217 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 10.2.3.11 Power State Control (PWRSTATECTL) Register The Power State Control register (PWRSTATECTL) is controlled by the software to indicate the powersaving mode. Under ROM code, the C66x CorePac reads this register to differentiate between the various power saving modes. This register is cleared only by POR and is not changed by any other device reset. See Hardware Design Guide for KeyStone II Devices for more information. The PWRSTATECTL register is shown in Figure 10-21 and described in Table 10-41. Figure 10-21. Power State Control Register (PWRSTATECTL) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 Hibernation Recovery Branch Address Width Wait Recovery Master Local Reset Action RW-0000 0000 0000 0000 00 RW-0 RW-0 RW-0 RW-0 4 3 Stored SR Index RW-0 2 1 0 Hibernation Hibernation Rsvd Mode RW-0 RW-0 R-0 Legend: R = Read Only, RW = Read/Write; -n = value after reset Table 10-41. Power State Control Register Field Descriptions Bit Field Description 31-10 Hibernation Recovery Branch Address Used to provide a start address for execution out of the hibernation modes. See the KeyStone Architecture DSP Bootloader User's Guide. 9 Width EMIF16 Width (if the recovery address is in EMIF16 space). • 0 = 8-bit • 1 = 16-bit 8 Wait Extended Wait (if the recovery address is in EMIF16 space) • 0 = Extended Wait disabled • 1 = Extended Wait enabled 7 Recovery Master Master performs hibernation recovery • 0 = C66x CorePacs perform hibernation recovery • 1 = ARM CorePac performs hibernation recovery 6-5 Local Reset Action Action of Local Reset • 00 = Idle on Local Reset • 01 = Branch to the base of MSMC on Local Reset • 10 = Branch to the base of DDR3 on Local Reset • 11 = Branch to the base of L2 on Local Reset (C66x CorePac) 4-3 Stored Index 0-3 value latched in the SR bits of the DEVSTAT register 2 Hibernation Mode Indicates whether the device is in hibernation mode 1 or mode 2. • 0 = Hibernation mode 1 • 1 = Hibernation mode 2 1 Hibernation Indicates whether the device is in hibernation mode or not. • 0 = Not in hibernation mode • 1 = Hibernation mode 0 Reserved Reserved 10.2.3.12 NMI Event Generation to C66x CorePac (NMIGRx) Register NMIGRx registers generate NMI events to the corresponding C66x CorePac. The 66AK2Hxx has eight (66AK2H12) or four (66AK2H06) NMIGRx registers (NMIGR0 through NMIGR7). The NMIGR0 register generates an NMI event to C66x CorePac0, the NMIGR1 register generates an NMI event to C66x CorePac1, and so on. Writing a 1 to the NMIG field generates an NMI pulse. Writing a 0 has no effect and Reads return 0 and have no other effect. The NMI event generation to the C66x CorePac is shown in Figure 10-22 and described in Table 10-42. 218 Device Boot and Configuration Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Figure 10-22. NMI Generation Register (NMIGRx) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Reserved NMIG R-0000 0000 0000 0000 0000 0000 0000 000 RW-0 Legend: RW = Read/Write; -n = value after reset Table 10-42. NMI Generation Register Field Descriptions Bit Field Description 31-1 Reserved Reserved 0 NMIG Reads return 0 Writes: • 0 = No effect • 1 = Creates NMI pulse to the corresponding C66x CorePac — C66x CorePac0 for NMIGR0, and so forth. 10.2.3.13 IPC Generation (IPCGRx) Registers The IPCGRx registers facilitate inter-C66x CorePac interrupts. The 66AK2H12 device has 12 IPCGRx registers (IPCGR0 through IPCGR11) and the 66AK2H06 has six IPCGRx registers (IPCGR0 through IPCGR3 and IPCGR8 and IPCGR9). These registers can be used by external hosts or CorePacs to generate interrupts to other CorePacs. A write of 1 to the IPCG field of the IPCGRx register generates an interrupt pulse to the: • C66x CorePacx (0 >1) – 1. 23 BYPASS PLL bypass mode: • 0 = PLL is not in BYPASS mode • 1 = PLL is in BYPASS mode 22-19 CLKOD A 4-bit field that selects the values for the PLL post divider. Valid post divider values are 1 and even values from 2 to 16. CLKOD field is loaded with output divide value minus 1 18-6 PLLM A 13-bit field that selects the values for the PLL multiplication factor. PLLM field is loaded with the multiply factor minus 1 5-0 PLLD A 6-bit field that selects the values for the reference (input) divider. PLLD field is loaded with reference divide value minus 1 Figure 11-27. DDR3A PLL and DDR3B PLL Control Register 1 (DDR3APLLCTL0/DDR3BPLLCTL1) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 Reserved PLLRST Reserved RW-00000000000000000 RW-0 RW-0000000 8 7 6 5 4 3 ENSAT Reserved RW-0 R-00 2 1 0 BWADJ[11:8] RW-0000 Legend: RW = Read/Write; – n = value after reset Table 11-31. DDR3A PLL and DDR3B PLL Control Register 1 Field Descriptions Bit Field Description 31-15 Reserved Reserved 14 PLLRST PLL Reset bit • 0 = PLL Reset is released • 1 = PLL Reset is asserted 13-7 Reserved Reserved 6 ENSAT Needs to be set to 1 for proper PLL operation 5-4 Reserved Reserved 3-0 BWADJ[11:8] BWADJ[11:8] and BWADJ[7:0] are in DDR3PLLCTL0 and DDR3PLLCTL1 registers. BWADJ[11:0] should be programmed to a value related to PLLM[12:0] value based on the equation: BWADJ = ((PLLM+1)>>1) – 1. 11.6.2 DDR3A PLL and DDR3B PLL Device-Specific Information As shown in Figure 11-25, the output of DDR3A PLL and DDR3B PLL (PLLOUT) is divided by 2 and directly fed to the DDR3A and DDR3B memory controller. During power-on resets, the internal clocks of the DDR3 PLL are affected as described in Section 11.4. The DDR3 PLL is unlocked only during the power-up sequence and is locked by the time the RESETSTAT pin goes high. It does not lose lock during any of the other resets. 11.6.3 DDR3 PLL Input Clock Electrical Data and Timing Table 11-32 applies to both DDR3A and DDR3B memory interfaces. Table 11-32. DDR3 PLL DDRCLK(N|P) Timing Requirements (see Figure 11-28 and Figure 11-22) NO. MIN MAX UNIT DDRCLK[P:N] 1 tc(DDRCLKN) Cycle time _ DDRCLKN cycle time Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 3.2 25 66AK2Hxx Peripheral Information ns 273 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-32. DDR3 PLL DDRCLK(N|P) Timing Requirements (continued) (see Figure 11-28 and Figure 11-22) NO. MIN 1 tc(DDRCLKP) Cycle time _ DDRCLKP cycle time 3 tw(DDRCLKN) 2 2 MAX UNIT 3.2 25 ns Pulse width _ DDRCLKN high 0.45*tc(DDRCLKN) 0.55*tc(DDRCLKN) ns tw(DDRCLKN) Pulse width _ DDRCLKN low 0.45*tc(DDRCLKN) 0.55*tc(DDRCLKN) ns tw(DDRCLKP) Pulse width _ DDRCLKP high 0.45*tc(DDRCLKP) 0.55*tc(DDRCLKP) ns 3 tw(DDRCLKP) Pulse width _ DDRCLKP low 0.45*tc(DDRCLKP) 0.55*tc(DDRCLKP) ns 4 tr(DDRCLK_200 mV) Transition time _ DDRCLK differential rise time (200 mV) 50 350 ps 4 tf(DDRCLK_200 mV) Transition time _ DDRCLK differential fall time (200 mV) 50 350 ps 5 tj(DDRCLKN) Jitter, peak_to_peak _ periodic DDRCLKN 0.02*tc(DDRCLKN) ps 5 tj(DDRCLKP) Jitter, peak_to_peak _ periodic DDRCLKP 0.02*tc(DDRCLKP) ps 1 2 3 DDRCLKN DDRCLKP 4 5 Figure 11-28. DDR3 PLL DDRCLK Timing 274 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.7 PASS PLL The PASS PLL generates interface clocks for the Network Coprocessor. Using the PACLKSEL pin the user can select the input source of the PASS PLL as either the output of the Main PLL mux or the PASSCLK clock reference source. When coming out of power-on reset, PASS PLL comes out in a bypass mode and needs to be programmed to a valid frequency before being enabled and used. PASS PLL power is supplied via the PASS PLL power-supply pin (AVDDA3). An external EMI filter circuit must be added to all PLL supplies. See Hardware Design Guide for KeyStone II Devices for detailed recommendations. The PASS PLL block diagram is shown in Figure 11-29. SYSCLK(P|N) PLLOUT PLL ALTCORECLK(P|N) SYSCLKn PLL Controller C66x CorePac CORECLKSEL PLLM PASS PLL VCO PASSCLK(P|N) /3 0 PLLOUT Network Coprocessor CLKOD PLLD 1 PACLKSEL BYPASS Copyright © 2016, Texas Instruments Incorporated Figure 11-29. PASS PLL Block Diagram 11.7.1 PASS PLL Local Clock Dividers The clock signal from the PASS PLL controller is routed to the network coprocessor. The NetCP module has two internal dividers with fixed division ratios, as shown in . 11.7.2 PASS PLL Control Registers The PASS PLL, which is used to drive the network coprocessor, does not use a PLL controller. PASS PLL can be controlled using the PAPLLCTL0 and PAPLLCTL1 registers in the Bootcfg module. These MMRs (memory-mapped registers) exist inside the Bootcfg space. To write to these registers, software must go through an unlocking sequence using the KICK0 and KICK1 registers. For suggested configuration values, see Section 10.1.4. See Section 10.2.3.4 for the address location of the registers and locking and unlocking sequences for accessing these registers. These registers are reset on POR only. The PASS PLL control registers are shown in Figure 11-30 and Figure 11-31 and described in Table 1133 and Table 11-34. Figure 11-30. PASS PLL Control Register 0 (PASSPLLCTL0) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 BWADJ[7:0] BYPASS CLKOD PLLM PLLD RW-0000 1001 RW-1 RW-0001 RW-0000000010011 RW-000000 1 0 LEGEND: RW = Read/Write; -n = value after reset Table 11-33. PASS PLL Control Register 0 Field Descriptions (PASSPLLCTL0) Bit Field Description 31-24 BWADJ[7:0] BWADJ[11:8] and BWADJ[7:0] are in PASSPLLCTL0 and PASSPLLCTL1 registers. BWADJ[11:0] should be programmed to a value related to PLLM[12:0] value based on the equation: BWADJ = ((PLLM+1)>>1) – 1. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 275 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-33. PASS PLL Control Register 0 Field Descriptions (PASSPLLCTL0) (continued) Bit Field Description 23 BYPASS PLL bypass mode: • 0 = PLL is not in BYPASS mode • 1 = PLL is in BYPASS mode 22-19 CLKOD A 4-bit field that selects the values for the PLL post divider. Valid post divider values are 1 and even values from 2 to 16. CLKOD field is loaded with output divide value minus 1 18-6 PLLM A 13-bit field that selects the values for the multiplication factor (see note below). PLLM field is loaded with the multiply factor minus 1. 5-0 PLLD A 6-bit field that selects the values for the reference divider. PLLD field is loaded with reference divide value minus 1. Figure 11-31. PASS PLL Control Register 1 (PASSPLLCTL1) 31 30 29 28 27 26 25 24 14 13 Reserved 23 22 21 20 19 18 17 16 15 PLLRST PAPLL 12 11 Reserved 10 9 8 RW-00000000000000000 RW-0 RW-0 RW-0000000 7 6 5 4 3 ENSAT Reserved RW-0 2 1 0 BWADJ[11:8] R-00 RW-0000 Legend: RW = Read/Write; – n = value after reset Table 11-34. PASS PLL Control Register 1 Field Descriptions (PASSPLLCTL1) Bit Field Description 31-15 Reserved Reserved 14 PLLRST PLL Reset bit • 0 = PLL Reset is released • 1 = PLL Reset is asserted 13 PAPLL • • 12-7 Reserved Reserved 6 ENSAT Needs to be set to 1 for proper PLL operation 5-4 Reserved Reserved 3-0 BWADJ[11:8] BWADJ[11:8] and BWADJ[7:0] are in PASSPLLCTL0 and PASSPLLCTL1 registers. BWADJ[11:0] should be programmed to a value related to PLLM[12:0] value based on the equation: BWADJ = ((PLLM+1)>>1) – 1. 0 = Not supported 1 = PAPLL 11.7.3 PASS PLL Device-Specific Information As shown in Figure 11-29, the output of PASS PLL (PLLOUT) is divided by 3 and directly fed to the Network Coprocessor. During power-on resets, the internal clocks of the PASS PLL are affected as described in Section 11.4. The PASS PLL is unlocked only during the power-up sequence and is locked by the time the RESETSTAT pin goes high. It does not lose lock during any other resets. 11.7.4 PASS PLL Input Clock Electrical Data and Timing Table 11-35 shows the PASS PLL timing requirements. Table 11-35. PASS PLL Timing Requirements (see Figure 11-32 and Figure 11-22) NO. MIN MAX UNIT PASSCLK[P:N] 1 tc(PASSCLKN) Cycle time _ PASSCLKN cycle time 3.2 6.4 ns 1 tc(PASSCLKP) Cycle time _ PASSCLKP cycle time 3.2 6.4 ns 3 tw(PASSCLKN) Pulse width _ PASSCLKN high 0.45*tc(PASSCLKN) 0.55*tc(PASSCLKN) ns 2 tw(PASSCLKN) Pulse width _ PASSCLKN low 0.45*tc(PASSCLKN) 0.55*tc(PASSCLKN) ns 2 tw(PASSCLKP) Pulse width _ PASSCLKP high 0.45*tc(PASSCLKP) 0.55*tc(PASSCLKP) ns 3 tw(PASSCLKP) Pulse width _ PASSCLKP low 0.45*tc(PASSCLKP) 0.55*tc(PASSCLKP) ns 4 tr(PASSCLK_200mV) Transition time _ PASSCLK differential rise time (200 mV) 50 350 ps 276 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-35. PASS PLL Timing Requirements (continued) (see Figure 11-32 and Figure 11-22) NO. MIN MAX 50 350 ps Jitter, peak_to_peak _ periodic PASSCLKN 100 ps, pk-pk Jitter, peak_to_peak _ periodic PASSCLKP 100 ps, pk-pk 4 tf(PASSCLK_200mV) Transition time _ PASSCLK differential fall time (200 mV) 5 tj(PASSCLKN) 5 tj(PASSCLKP) UNIT 1 2 3 PASSCLKN PASSCLKP 5 4 Figure 11-32. PASS PLL Timing 11.8 External Interrupts 11.8.1 External Interrupts Electrical Data and Timing Table 11-36 shows the NMI and LRESET timing requirements. Table 11-36. NMI and LRESET Timing Requirements (1) (see Figure 11-33) NO. MIN MAX UNIT 1 tsu( LRESET – LRESETNMIEN) Setup time – LRESET valid before LRESETNMIEN low 12*P ns 1 tsu( NMI – LRESETNMIEN) Setup time – NMI valid before LRESETNMIEN low 12*P ns 1 tsu(CORESELn – LRESETNMIEN) Setup time – CORESEL[3:0] valid before LRESETNMIEN low 12*P ns 2 th(LRESETNMIEN – LRESET) Hold time – LRESET valid after LRESETNMIEN high 12*P ns 2 th(LRESETNMIEN – NMI) Hold time – NMI valid after LRESETNMIEN high 12*P ns 2 th(LRESETNMIEN – CORESELn) Hold time – CORESEL[3:0] valid after LRESETNMIEN high 12*P ns 3 tw(LRESETNMIEN) Pulsewidth – LRESETNMIEN low width 12*P ns (1) P = 1/SYSCLK1 clock frequency in ns. 1 2 CORESEL[3:0]/ LRESET/ NMI 3 LRESETNMIEN Figure 11-33. NMI and LRESET Timing Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 277 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.9 DDR3A and DDR3B Memory Controllers The 72-bit DDR3 memory controller bus of the 66AK2Hxx is used to interface to JEDEC standardcompliant DDR3 SDRAM devices. The DDR3 external bus interfaces only to DDR3 SDRAM devices and does not share the bus with any other type of peripheral. 11.9.1 DDR3 Memory Controller Device-Specific Information The 66AK2Hxx includes one 64-bit wide, 1.35-V / 1.5-V DDR3 SDRAM EMIF interface. The DDR3 interface can operate at 800 mega transfers per second (MTS), 1033 MTS, 1333 MTS, and 1600 MTS. Due to the complicated nature of the interface, a limited number of topologies are supported to provide a 16-bit, 32-bit, or 64-bit interface. The DDR3 electrical requirements are fully specified in the DDR JEDEC specification JESD79-3C. Standard DDR3 SDRAMs are available in 8-bit and 16-bit versions allowing for the following bank topologies to be supported by the interface: • 72-bit: Five 16-bit SDRAMs (including 8 bits of ECC) • 72-bit: Nine 8-bit SDRAMs (including 8 bits of ECC) • 36-bit: Three 16-bit SDRAMs (including 4 bits of ECC) • 36-bit: Five 8-bit SDRAMs (including 4 bits of ECC) • 64-bit: Four 16-bit SDRAMs • 64-bit: Eight 8-bit SDRAMs • 32-bit: Two 16-bit SDRAMs • 32-bit: Four 8-bit SDRAMs • 16-bit: One 16-bit SDRAM • 16-bit: Two 8-bit SDRAMs The approach to specifying interface timing for the DDR3 memory bus is different than on other interfaces such as I2C or SPI. For these other interfaces, the device timing was specified in terms of data manual specifications and I/O buffer information specification (IBIS) models. For the DDR3 memory bus, the approach is to specify compatible DDR3 devices and provide the printed-circuit board (PCB) solution and guidelines directly to the user. A race condition may exist when certain masters write data to the DDR3 memory controller. For example, if master A passes a software message via a buffer in external memory and does not wait for an indication that the write completes before signaling to master B that the message is ready, when master B attempts to read the software message, the master B read may bypass the master A write. Thus, master B may read stale data and receive an incorrect message. Some master peripherals (for example, EDMA3 transfer controllers with TCCMOD=0) always wait for the write to complete before signaling an interrupt to the system, thus avoiding this race condition. For masters that do not have a hardware specification of write-read ordering, it may be necessary to specify data ordering in the software. If master A does not wait for an indication that a write is complete, it must perform the following workaround: 1. Perform the required write to DDR3 memory space. 2. Perform a dummy write to the DDR3 memory controller module ID and revision register. 3. Perform a dummy read to the DDR3 memory controller module ID and revision register. 4. Indicate to master B that the data is ready to be read after completion of the read in Step 3. The completion of the read in Step 3 ensures that the previous write was done. 278 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.9.2 DDR3 Slew Rate Control The DDR3 slew rate is controlled by use of the PHY registers. See the Keystone II Architecture DDR3 Memory Controller User's Guide for details. 11.9.3 DDR3 Memory Controller Electrical Data and Timing DDR3 Design Requirements for KeyStone Devices specifies a complete DDR3 interface solution as well as a list of compatible DDR3 devices. The DDR3 electrical requirements are fully specified in the DDR3 JEDEC Specification JESD79-3C. TI has performed the simulation and system characterization to ensure all DDR3 interface timings in this solution are met. Therefore, no electrical data and timing information is supplied here for this interface. NOTE TI supports only designs that follow the board design guidelines outlined in the application report. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 279 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.10 I2C Peripheral The Inter-Integrated Circuit (I2C) module provides an interface between SoC and other devices compliant with Philips Semiconductors (now NXP Semiconductors) Inter-Integrated Circuit bus specification version 2.1. External components attached to this 2-wire serial bus can transmit/receive up to 8-bit data to/from the device through the I2C module. 11.10.1 I2C Device-Specific Information The device includes multiple I2C peripheral modules. NOTE When using the I2C module, ensure there are external pullup resistors on the SDA and SCL pins. The I2C modules on the 66AK2Hxx may be used by the SoC to control local peripheral ICs (DACs, ADCs, and so forth), communicate with other controllers in a system, or to implement a user interface. The I2C port supports: • Compatibility with Philips I2C specification revision 2.1 (January 2000) • Fast mode up to 400 kbps (no fail-safe I/O buffers) • Noise filter to remove noise of 50 ns or less • 7-bit and 10-bit device addressing modes • Multimaster (transmit/receive) and slave (transmit/receive) functionality • Events: DMA, interrupt, or polling • Slew-rate limited open-drain output buffers Figure 11-34 shows a block diagram of the I2C module. 280 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 2 I C Module Clock Prescale Peripheral Clock (CPU/6) 2 I CPSC Control Bit Clock Generator SCL Noise Filter 2 I C Clock 2 Own Address 2 Slave Address I COAR 2 I CCLKH I CSAR 2 I CCLKL 2 I CMDR 2 I CCNT Transmit 2 I CXSR 2 I CDXR Transmit Shift 2 I CEMDR Extended Mode Interrupt/DMA Noise Filter I C Data Data Count Transmit Buffer SDA 2 Mode 2 I CDRR 2 I CRSR 2 Interrupt Mask/Status 2 Interrupt Status I CIMR Receive Receive Buffer I CSTR Receive Shift I CIVR 2 Interrupt Vector Shading denotes control/status registers. Copyright © 2016, Texas Instruments Incorporated 2 Figure 11-34. I C Module Block Diagram 11.10.2 I2C Peripheral Register Description Table 11-37 lists the I2C registers. Table 11-37. I2C Registers HEX ADDRESS OFFSETS ACRONYM REGISTER NAME 0x0000 ICOAR I2C Own Address Register 0x0004 ICIMR I2C Interrupt Mask/status Register 0x0008 ICSTR I2C Interrupt Status Register 0x000C ICCLKL I2C Clock Low-time Divider Register 0x0010 ICCLKH I2C Clock High-time Divider Register 0x0014 ICCNT I2C Data Count Register 0x0018 ICDRR I2C Data Receive Register 0x001C ICSAR I2C Slave Address Register 0x0020 ICDXR I2C Data Transmit Register 0x0024 ICMDR I2C Mode Register 0x0028 ICIVR I2C Interrupt Vector Register 0x002C ICEMDR I2C Extended Mode Register 0x0030 ICPSC I2C Prescaler Register Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 281 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-37. I2C Registers (continued) HEX ADDRESS OFFSETS ACRONYM REGISTER NAME 0x0034 ICPID1 I2C Peripheral Identification Register 1 [value: 0x0000 0105] 0x0038 ICPID2 I2C Peripheral Identification Register 2 [value: 0x0000 0005] 0x003C -0x007F - Reserved 11.10.3 I2C Electrical Data and Timing Table 11-38 shows the I2C timing requirements and Table 11-39 shows the I2C switching characteristics. Table 11-38. I2C Timing Requirements (1) (see Figure 11-35) STANDARD MODE NO. 1 MIN MAX FAST MODE MIN MAX UNIT tc(SCL) Cycle time, SCL 10 2.5 µs 2 tsu(SCLH-SDAL) Setup time, SCL high before SDA low (for a repeated START condition) 4.7 0.6 µs 3 th(SDAL-SCLL) Hold time, SCL low after SDA low (for a START and a repeated START condition) 4 0.6 µs 4 tw(SCLL) Pulse duration, SCL low 4.7 1.3 µs 5 tw(SCLH) Pulse duration, SCL high 4 0.6 µs 6 tsu(SDAV-SCLH) Setup time, SDA valid before SCL high 250 100 (2) 7 th(SCLL-SDAV) Hold time, SDA valid after SCL low (for I2C bus devices) 0 (3) 8 tw(SDAH) Pulse duration, SDA high between STOP and START conditions 4.7 9 tr(SDA) Rise time, SDA 3.45 0 (3) ns 0.9 (4) 1.3 µs µs 1000 20 + 0.1Cb (5) 300 ns (5) 10 tr(SCL) Rise time, SCL 1000 300 ns 11 tf(SDA) Fall time, SDA 300 20 + 0.1Cb (5) 300 ns 12 tf(SCL) Fall time, SCL 300 20 + 0.1Cb (5) 300 ns 13 tsu(SCLH-SDAH) Setup time, SCL high before SDA high (for STOP condition) 14 tw(SP) Cb (1) (2) (3) (4) (5) 282 (5) 4 20 + 0.1Cb 0.6 Pulse duration, spike (must be suppressed) 0 Capacitive load for each bus line 400 µs 50 ns 400 pF The I2C pins SDA and SCL do not feature fail-safe I/O buffers. These pins could potentially draw current when the device is powered down. A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement tsu(SDA-SCLH) ≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line tr max + tsu(SDA-SCLH) = 1000 + 250 = 1250 ns (according to the Standard-mode I2C-Bus Specification) before the SCL line is released. A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. The maximum th(SDA-SCLL) has to be met only if the device does not stretch the low period [tw(SCLL)] of the SCL signal. Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed. 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11 9 SDA 8 6 4 14 13 5 10 SCL 1 3 12 7 2 3 Stop Start Repeated Start Stop Figure 11-35. I2C Receive Timings Table 11-39. I2C Switching Characteristics (1) (see Figure 11-36) STANDARD MODE NO. 16 PARAMETER MIN FAST MODE MAX MIN MAX UNIT tc(SCL) Cycle time, SCL 10 2.5 µs 17 tsu(SCLH-SDAL) Setup time, SCL high to SDA low (for a repeated START condition) 4.7 0.6 µs 18 th(SDAL-SCLL) Hold time, SDA low after SCL low (for a START and a repeated START condition) 4 0.6 µs 19 tw(SCLL) Pulse duration, SCL low 4.7 1.3 µs 20 tw(SCLH) Pulse duration, SCL high 4 0.6 µs 21 td(SDAV-SDLH) Delay time, SDA valid to SCL high 250 100 22 tv(SDLL-SDAV) Valid time, SDA valid after SCL low (for I2C bus devices) 0 0 23 tw(SDAH) Pulse duration, SDA high between STOP and START conditions 4.7 1.3 24 tr(SDA) Rise time, SDA 1000 20 + 0.1Cb (1) 300 ns 25 tr(SCL) Rise time, SCL 1000 20 + 0.1Cb (1) 300 ns 26 tf(SDA) Fall time, SDA 300 20 + 0.1Cb (1) 300 ns 300 (1) 300 27 tf(SCL) Fall time, SCL 28 td(SCLH-SDAH) Delay time, SCL high to SDA high (for STOP condition) Cp Capacitance for each I2C pin (1) 4 20 + 0.1Cb ns 0.9 µs 0.6 10 µs ns µs 10 pF Cb = total capacitance of one bus line in pF. If mixed with HS-mode devices, faster fall-times are allowed. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 283 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 26 24 SDA 23 21 19 28 20 25 SCL 16 18 27 22 17 18 Stop Start Repeated Start Stop Figure 11-36. I2C Transmit Timings 11.11 SPI Peripheral The Serial Peripheral Interconnect (SPI) module provides an interface between the SoC and other SPIcompliant devices. The primary intent of this interface is to allow for connection to an SPI ROM for boot. The SPI module on 66AK2Hxx is supported only in master mode. Additional chip-level components can also be included, such as temperature sensors or an I/O expander. 11.11.1 SPI Electrical Data and Timing Table 11-40 shows the SPI timing requirements and Table 11-41 shows the SPI switching characteristics. Table 11-40. SPI Timing Requirements (see Figure 11-37) NO. MIN MAX UNIT Master Mode Timing Diagrams — Base Timings for 3 Pin Mode 7 tsu(SPIDIN-SPC) Input setup time, SPIDIN valid before receive edge of SPICLK. Polarity = 0 Phase = 0 2 ns 7 tsu(SPIDIN-SPC) Input setup time, SPIDIN valid before receive edge of SPICLK. Polarity = 0 Phase = 1 2 ns 7 tsu(SPIDIN-SPC) Input setup time, SPIDIN valid before receive edge of SPICLK. Polarity = 1 Phase = 0 2 ns 7 tsu(SPIDIN-SPC) Input setup time, SPIDIN valid before receive edge of SPICLK. Polarity = 1 Phase = 1 2 ns 8 th(SPC-SPIDIN) Input hold time, SPIDIN valid after receive edge of SPICLK. Polarity = 0 Phase = 0 5 ns 8 th(SPC-SPIDIN) Input hold time, SPIDIN valid after receive edge of SPICLK. Polarity = 0 Phase = 1 5 ns 8 th(SPC-SPIDIN) Input hold time, SPIDIN valid after receive edge of SPICLK. Polarity = 1 Phase = 0 5 ns 8 th(SPC-SPIDIN) Input hold time, SPIDIN valid after receive edge of SPICLK. Polarity = 1 Phase = 1 5 ns Table 11-41. SPI Switching Characteristics (see Figure 11-37 and Figure 11-38) NO. PARAMETER MIN MAX UNIT Master Mode Timing Diagrams — Base Timings for 3 Pin Mode 3*P2 (1) ns Pulse width high, SPICLK, all master modes 0.5*(3*P2) – 1 ns tw(SPCL) Pulse width low, SPICLK, all master modes 0.5*(3*P2) – 1 ns 4 td(SPIDOUT-SPC) Setup (Delay), initial data bit valid on SPIDOUT to initial edge on SPICLK. Polarity = 0, Phase = 0. 5 ns 4 td(SPIDOUT-SPC) Setup (Delay), initial data bit valid on SPIDOUT to initial edge on SPICLK. Polarity = 0, Phase = 1. 5 ns 1 tc(SPC) Cycle time, SPICLK, all master modes 2 tw(SPCH) 3 (1) 284 P2=1/(SYSCLK1/6) 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-41. SPI Switching Characteristics (continued) (see Figure 11-37 and Figure 11-38) NO. PARAMETER MIN MAX UNIT 4 td(SPIDOUT-SPC) Setup (Delay), initial data bit valid on SPIDOUT to initial edge on SPICLK Polarity = 1, Phase = 0 4 td(SPIDOUT-SPC) Setup (Delay), initial data bit valid on SPIDOUT to initial edge on SPICLK Polarity = 1, Phase = 1 5 ns 5 td(SPC-SPIDOUT) Setup (Delay), subsequent data bits valid on SPIDOUT to initial edge on SPICLK. Polarity = 0 Phase = 0 2 ns 5 td(SPC-SPIDOUT) Setup (Delay), subsequent data bits valid on SPIDOUT to initial edge on SPICLK Polarity = 0 Phase = 1 2 ns 5 td(SPC-SPIDOUT) Setup (Delay), subsequent data bits valid on SPIDOUT to initial edge on SPICLK Polarity = 1 Phase = 0 2 ns 5 td(SPC-SPIDOUT) Setup (Delay), subsequent data bits valid on SPIDOUT to initial edge on SPICLK Polarity = 1 Phase = 1 2 ns 6 toh(SPC-SPIDOUT) Output hold time, SPIDOUT valid after receive edge of SPICLK except for final bit. Polarity = 0 Phase = 0 0.5*tc – 2 ns 6 toh(SPC-SPIDOUT) Output hold time, SPIDOUT valid after receive edge of SPICLK except for final bit. Polarity = 0 Phase = 1 0.5*tc – 2 ns 6 toh(SPC-SPIDOUT) Output hold time, SPIDOUT valid after receive edge of SPICLK except for final bit. Polarity = 1 Phase = 0 0.5*tc – 2 ns 6 toh(SPC-SPIDOUT) Output hold time, SPIDOUT valid after receive edge of SPICLK except for final bit. Polarity = 1 Phase = 1 0.5*tc – 2 ns 19 td(SCS-SPC) Delay from SPISCSx\ active to first SPICLK. Polarity = 0 Phase = 0 2*P2 – 5 2*P2 + 5 ns 19 td(SCS-SPC) Delay from SPISCSx\ active to first SPICLK. Polarity = 0 Phase = 1 0.5*tc + (2*P2) – 5 0.5*tc + (2*P2) + 5 ns 19 td(SCS-SPC) Delay from SPISCSx\ active to first SPICLK. Polarity = 1 Phase = 0 2*P2 – 5 2*P2 + 5 ns 19 td(SCS-SPC) Delay from SPISCSx\ active to first SPICLK. Polarity = 1 Phase = 1 0.5*tc + (2*P2) – 5 0.5*tc + (2*P2) + 5 ns 20 td(SPC-SCS) Delay from final SPICLK edge to master deasserting SPISCSx\. Polarity = 0 Phase = 0 1*P2 – 5 1*P2 + 5 ns 20 td(SPC-SCS) Delay from final SPICLK edge to master deasserting SPISCSx\. Polarity = 0 Phase = 1 0.5*tc + (1*P2) – 5 0.5*tc + (1*P2) + 5 ns 20 td(SPC-SCS) Delay from final SPICLK edge to master deasserting SPISCSx\. Polarity = 1 Phase = 0 1*P2 – 5 1*P2 + 5 ns 20 td(SPC-SCS) Delay from final SPICLK edge to master deasserting SPISCSx\. Polarity = 1 Phase = 1 0.5*tc + (1*P2) – 5 0.5*tc + (1*P2) + 5 ns tw(SCSH) Minimum inactive time on SPISCSx\ pin between two transfers when SPISCSx\ is not held using the CSHOLD feature. 5 ns Additional SPI Master Timings — 4 Pin Mode with Chip Select Option 2*P2 – 5 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information ns 285 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 1 2 MASTER MODE POLARITY = 0 PHASE = 0 3 SPICLK 5 4 SPIDOUT MO(0) 7 SPIDIN 6 MO(1) MO(n−1) MO(n) MI(n−1) MI(n) 8 MI(0) MI(1) MASTER MODE POLARITY = 0 PHASE = 1 4 SPICLK 6 5 MO(0) SPIDOUT 7 MO(n−1) MO(n) MI(1) MI(n−1) 8 MI(0) SPIDIN MO(1) 4 MI(n) MASTER MODE POLARITY = 1 PHASE = 0 SPICLK 5 SPIDOUT 6 MO(0) 7 MO(1) MO(n) 8 MI(0) SPIDIN MO(n−1) MI(1) MI(n−1) MI(n) MASTER MODE POLARITY = 1 PHASE = 1 SPICLK 5 4 SPIDOUT MO(0) 7 SPIDIN 6 MO(1) MO(n−1) MI(1) MI(n−1) MO(n) 8 MI(0) MI(n) Figure 11-37. SPI Master Mode Timing Diagrams — Base Timings for 3-Pin Mode MASTER MODE 4 PIN WITH CHIP SELECT 19 20 SPICLK SPIDOUT SPIDIN MO(0) MI(0) MO(1) MO(n−1) MO(n) MI(1) MI(n−1) MI(n) SPISCSx Figure 11-38. SPI Additional Timings for 4-Pin Master Mode with Chip Select Option 286 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.12 HyperLink Peripheral The 66AK2Hxx includes HyperLinks for companion device interfaces. This is a four-lane SerDes interface designed to operate at up to 10 Gbps per lane from pin-to-pin. The interface is used to connect with external accelerators that are manufactured using TI libraries. The HyperLink lines must be connected with DC coupling. The interface includes the serial station management interfaces used to send power management and flow messages between devices. Each HyperLink interface consists of four LVCMOS inputs and four LVCMOS outputs configured as two 2-wire input buses and two 2-wire output buses. Each 2-wire bus includes a data signal and a clock signal. Table 11-42 shows the Hyperlink timing requirements and Table 11-43 shows the Hyperlink switching characteristics. Table 11-42. HyperLink Peripheral Timing Requirements (see Figure 11-39, Figure 11-40, and Figure 11-41) NO. MIN MAX UNIT FL Interface 1 tc(HYPTXFLCLK) Clock period – HYPTXFLCLK (C1) 2 tw(HYPTXFLCLKH) High pulse width – HYPTXFLCLK 0.4*C1 0.6*C1 ns 3 tw(HYPTXFLCLKL) Low pulse width – HYPTXFLCLK 0.4*C1 0.6*C1 ns tsu(HYPTXFLDAT-HYPTXFLCLKH) Setup time – HYPTXFLDAT valid before HYPTXFLCLK high 1 th(HYPTXFLCLKH-HYPTXFLDAT) Hold time – HYPTXFLDAT valid after HYPTXFLCLK high 1 tsu(HYPTXFLDAT-HYPTXFLCLKL) Setup time – HYPTXFLDAT valid before HYPTXFLCLK low 1 th(HYPTXFLCLKL-HYPTXFLDAT) Hold time – HYPTXFLDAT valid after HYPTXFLCLK low 1 1 tc(HYPRXPMCLK) Clock period – HYPRXPMCLK (C3) 2 tw(HYPRXPMCLK) High pulse width – HYPRXPMCLK 0.4*C3 0.6*C3 ns 3 tw(HYPRXPMCLK) Low pulse width – HYPRXPMCLK 0.4*C3 0.6*C3 ns tsu(HYPRXPMDAT-HYPRXPMCLKH) Setup time – HYPRXPMDAT valid before HYPRXPMCLK high 1 th(HYPRXPMCLKH-HYPRXPMDAT) Hold time – HYPRXPMDAT valid after HYPRXPMCLK high 1 tsu(HYPRXPMDAT-HYPRXPMCLKL) Setup time – HYPRXPMDAT valid before HYPRXPMCLK low 1 th(HYPRXPMCLKL-HYPRXPMDAT) Hold time – HYPRXPMDAT valid after HYPRXPMCLK low 1 6 7 6 7 5.75 ns ns ns ns ns PM Interface 6 7 6 7 5.75 ns ns ns ns ns Table 11-43. HyperLink Peripheral Switching Characteristics (see Figure 11-39, Figure 11-40, and Figure 11-41) NO. PARAMETER MIN MAX UNIT FL Interface 1 tc(HYPRXFLCLK) Clock period – HYPRXFLCLK (C2) 2 tw(HYPRXFLCLKH) High pulse width – HYPRXFLCLK 0.4*C2 0.6*C2 ns 3 tw(HYPRXFLCLKL) Low pulse width – HYPRXFLCLK 0.4*C2 0.6*C2 ns tosu(HYPRXFLDAT-HYPRXFLCLKH) Setup time – HYPRXFLDAT valid before HYPRXFLCLK high 0.25*C2-0.4 toh(HYPRXFLCLKH-HYPRXFLDAT) Hold time – HYPRXFLDAT valid after HYPRXFLCLK high 0.25*C2-0.4 tosu(HYPRXFLDAT-HYPRXFLCLKL) Setup time – HYPRXFLDAT valid before HYPRXFLCLK low 0.25*C2-0.4 toh(HYPRXFLCLKL-HYPRXFLDAT) Hold time – HYPRXFLDAT valid after HYPRXFLCLK low 0.25*C2-0.4 4 5 4 5 6.4 ns ns ns ns ns PM Interface Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 287 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-43. HyperLink Peripheral Switching Characteristics (continued) (see Figure 11-39, Figure 11-40, and Figure 11-41) NO. PARAMETER MIN MAX tc(HYPTXPMCLK) Clock period – HYPTXPMCLK (C4) 2 tw(HYPTXPMCLK) High pulse width – HYPTXPMCLK 0.4*C4 0.6*C4 ns 3 tw(HYPTXPMCLK) Low pulse width – HYPTXPMCLK 0.4*C4 0.6*C4 ns tosu(HYPTXPMDAT-HYPTXPMCLKH) Setup time – HYPTXPMDAT valid before HYPTXPMCLK high 0.25*C2-0.4 toh(HYPTXPMCLKH-HYPTXPMDAT) Hold time – HYPTXPMDAT valid after HYPTXPMCLK high 0.25*C2-0.4 tosu(HYPTXPMDAT-HYPTXPMCLKL) Setup time – HYPTXPMDAT valid before HYPTXPMCLK low 0.25*C2-0.4 toh(HYPTXPMCLKL-HYPTXPMDAT) Hold time – HYPTXPMDAT valid after HYPTXPMCLK low 0.25*C2-0.4 4 5 4 5 6.4 UNIT 1 ns ns ns ns ns 1 2 3 Figure 11-39. HyperLink Station Management Clock Timing 4 5 4 5 HYPTXCLK HYPTXDAT represents the interface that is being used: PM or FL Figure 11-40. HyperLink Station Management Transmit Timing 6 7 6 7 HYPRXCLK HYPRXDAT represents the interface that is being used: PM or FL Figure 11-41. HyperLink Station Management Receive Timing 288 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.13 UART Peripheral The universal asynchronous receiver/transmitter (UART) module provides an interface between the device and a UART terminal interface or other UART-based peripheral. The UART is based on the industry standard TL16C550 asynchronous communications element which, in turn, is a functional upgrade of the TL16C450. Functionally similar to the TL16C450 on power up (single character or TL16C450 mode), the UART can be placed in an alternate FIFO (TL16C550) mode. This relieves the SoC of excessive software overhead by buffering received and transmitted characters. The receiver and transmitter FIFOs store up to 16 bytes including three additional bits of error status per byte for the receiver FIFO. The UART performs serial-to-parallel conversions on data received from a peripheral device and parallelto-serial conversion on data received from the C66x CorePac to be sent to the peripheral device. The C66x CorePac can read the UART status at any time. The UART includes control capability and a processor interrupt system that can be tailored to minimize software management of the communications link. For more information on UART, see the KeyStone Architecture Universal Asynchronous Receiver/Transmitter (UART) User's Guide. Table 11-44 shows the UART timing requirements and Table 11-45 shows the UART switching characteristics. Table 11-44. UART Timing Requirements (see Figure 11-42 and Figure 11-43) NO. MIN MAX UNIT 0.96U (1) Receive Timing 4 tw(RXSTART) Pulse width, receive start bit 1.05U ns 5 tw(RXH) Pulse width, receive data/parity bit high 0.96U 1.05U ns 5 tw(RXL) Pulse width, receive data/parity bit low 0.96U 1.05U ns 6 tw(RXSTOP1) Pulse width, receive stop bit 1 0.96U 1.05U ns 6 tw(RXSTOP15) Pulse width, receive stop bit 1.5 0.96U 1.05U ns 6 tw(RXSTOP2) Pulse width, receive stop bit 2 0.96U 1.05U ns 8 td(CTSL-TX) Delay time, CTS asserted to START bit transmit P (2) 5P ns Autoflow Timing Requirements (1) (2) U = UART baud time = 1/programmed baud rate P = 1/(SYSCLK1/6) 5 4 RXD Stop/Idle Start 5 Bit 1 Bit 0 Bit N-1 Bit N 6 Parity Stop Idle Start Figure 11-42. UART Receive Timing Waveform 8 TXD Bit N-1 Bit N Stop Start Bit 0 CTS Figure 11-43. UART CTS (Clear-to-Send Input) — Autoflow Timing Waveform Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 289 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-45. UART Switching Characteristics (see Figure 11-44 and Figure 11-45) NO. PARAMETER MIN MAX UNIT U (1)- 2 Transmit Timing 1 tw(TXSTART) Pulse width, transmit start bit U+2 ns 2 tw(TXH) Pulse width, transmit data/parity bit high U–2 U+2 ns 2 tw(TXL) Pulse width, transmit data/parity bit low U–2 U+2 ns 3 tw(TXSTOP1) Pulse width, transmit stop bit 1 U–2 U+2 ns 3 tw(TXSTOP15) Pulse width, transmit stop bit 1.5 1.5 × (U – 2) 1.5 × ('U + 2) ns 3 tw(TXSTOP2) Pulse width, transmit stop bit 2 2 × (U – 2) 2 × ('U + 2) ns P (2) 5P ns Autoflow Timing Requirements 7 td(RX-RTSH) (1) (2) Delay time, STOP bit received to RTS deasserted U = UART baud time = 1/programmed baud rate P = 1/(SYSCLK1/6) 1 TXD Start Stop/Idle 2 Bit 0 2 Bit 1 Bit N-1 Bit N Parity 3 Stop Idle Start Figure 11-44. UART Transmit Timing Waveform 7 RXD Bit N-1 Bit N Stop Start CTS Figure 11-45. UART RTS (Request-to-Send Output) – Autoflow Timing Waveform 11.14 PCIe Peripheral The two-lane PCI express (PCIe) module on 66AK2Hxx provides an interface between the device and other PCIe-compliant devices. The PCIe module provides low pin-count, high-reliability, and high-speed data transfer at rates up to 5.0 Gbps per lane on the serial links. For more information, see the KeyStone Architecture Peripheral Component Interconnect Express (PCIe) User's Guide. 11.15 Packet Accelerator The Packet Accelerator (PA) provides L2 to L4 classification functionalities and supports classification for Ethernet, VLAN, MPLS over Ethernet, IPv4/6, GRE over IP, and other session identification over IP such as UDP ports. It maintains 8k multiple-in, multiple-out hardware queues and also provides checksum capability as well as some QoS capabilities. The PA enables a single IP address to be used for a multicore device and can process up to 1.5 Mpps. The Packet Accelerator is coupled with the Network Coprocessor. For more information, see the KeyStone Architecture Packet Accelerator (PA) User’s Guide. 290 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.16 Security Accelerator The Security Accelerator (SA) provides wire-speed processing on 1 Gbps Ethernet traffic on IPSec, SRTP, and 3GPP Air interface security protocols. It functions on the packet level with the packet and the associated security context being one of the above three types. The Security Accelerator is coupled with the Network Coprocessor, and receives the packet descriptor containing the security context in the buffer descriptor and the data to be encrypted/decrypted in the linked buffer descriptor. For more information, see the KeyStone Architecture Security Accelerator (SA) User’s Guide . 11.17 Network Coprocessor Gigabit Ethernet (GbE) Switch Subsystem The gigabit Ethernet (GbE) switch subsystem provides an efficient interface between the device and the networked community. The Ethernet Media Access Controller (EMAC) supports 10Base-T (10 Mbits/second), and 100BaseTX (100 Mbps), in half- or full-duplex mode, and 1000BaseT (1000 Mbps) in full-duplex mode, with hardware flow control and quality-of-service (QOS) support. The GbE switch subsystem is coupled with the Network Coprocessor. For more information, see the Gigabit Ethernet (GbE) Switch Subsystem (1 GB) User's Guide. An address range is assigned to the 66AK2Hxx. Each individual device has a 48-bit MAC address and consumes only one unique MAC address out of the range. There are two registers to hold these values, MACID1[31:0] (32 bits) and MACID2[15:0] (16 bits). The MACID1 and MACID2 registers are shown in Figure 11-46 and Figure 11-47 and described in Table 11-46 and Table 11-47. Figure 11-46. MACID1 Register (MMR Address 0x02620110) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 2 1 0 MACID R,+xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx Legend: R = Read only; -x, value is indeterminate Table 11-46. MACID1 Register Field Descriptions Bit Field Description 31-0 MAC ID MAC ID. Lower 32 bits. Figure 11-47. MACID2 Register (MMR Address 0x02620114) 31 30 29 28 17 16 CRC 27 26 25 24 23 22 Reserved 21 20 19 18 FLOW BCAST 15 14 13 12 11 10 9 MACID 8 7 6 R+,cccc cccc R,+rr rrrr R,+z R,+y R,+xxxx xxxx xxxx xxxx 5 4 3 LEGEND: R = Read only; -x = value is indeterminate Table 11-47. MACID2 Register Field Descriptions Bit Field Description 31-24 CRC Variable 23-18 Reserved 000000 17 FLOW MAC Flow Control • 0 = Off • 1 = On 16 BCAST Default m/b-cast reception • 0 = Broadcast • 1 = Disabled 15-0 MAC ID MAC ID. Upper 16 bits. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 291 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com There is a central processor time synchronization (CPTS) submodule in the Ethernet switch module that can be used for time synchronization. Programming this register selects the clock source for the CPTS_RCLK. See the Gigabit Ethernet (GbE) Switch Subsystem (1 GB) User's Guide for the register address and other details about the time synchronization submodule. The register CPTS_RFTCLK_SEL for reference clock selection of the time synchronization submodule is shown in Figure 11-48 and described in Table 11-48. Figure 11-48. RFTCLK Select Register (CPTS_RFTCLK_SEL) 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Reserved CPTS_RFTCLK_SEL R-0 RW-0 Legend: R = Read only; -x, value is indeterminate Table 11-48. RFTCLK Select Register Field Descriptions Bit Field Description 31-4 Reserved Reserved. Read as 0. 3-0 CPTS_RFTCLK_SEL Reference clock select. This signal is used to control an external multiplexer that selects one of 8 clocks for time sync reference (RFTCLK). This CPTS_RFTCLK_SEL value can be written only when the CPTS_EN bit is cleared to 0 in the TS_CTL register. • 0000 = SYSCLK2 • 0001 = SYSCLK3 • 0010 = TIMI0 • 0011 = TIMI1 • 1000 = TSREFCLK • Others = Reserved 11.18 SGMII and XFI Management Data Input/Output (MDIO) The management data input/output (MDIO) module implements the 802.3 serial management interface to interrogate and control up to 32 Ethernet PHY(s) connected to the device, using a shared two-wire bus. Application software uses the MDIO module to configure the auto-negotiation parameters of each PHY attached to the EMAC, retrieve the negotiation results, and configure required parameters in the gigabit Ethernet (GbE) and 10-gigabit Ethernet (10GbE) switch subsystems for correct operation. The module allows almost transparent operation of the MDIO interface, with very little attention from the SoC. For more information, see the Gigabit Ethernet (GbE) Switch Subsystem (1 GB) User's Guide and the KeyStone II Architecture 10 Gigabit Ethernet Subsystem User's Guide. The MDIO timing requirements are shown in Table 11-49 and the MDIO switching characteristics are shown in Table 11-50. Table 11-49. MDIO Timing Requirements (see Figure 11-49) NO. MIN MAX UNIT 1 tc(MDCLK) Cycle time, MDCLK 400 ns 2 tw(MDCLKH) Pulse duration, MDCLK high 180 ns 3 tw(MDCLKL) Pulse duration, MDCLK low 180 ns 4 tsu(MDIO-MDCLKH) Setup time, MDIO data input valid before MDCLK high 10 ns 5 th(MDCLKH-MDIO) Hold time, MDIO data input valid after MDCLK high 10 tt(MDCLK) Transition time, MDCLK 292 66AK2Hxx Peripheral Information ns 5 ns Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 1 MDCLK 2 3 4 5 MDIO (Input) Figure 11-49. MDIO Input Timing Table 11-50. MDIO Switching Characteristics (see Figure 11-50) NO. MIN MAX UNIT 6 td(MDCLKH-MDIO) Delay time, MDCLK high to MDIO data output valid PARAMETER 10 300 ns 7 th(MDCLKH-MDIO) Hold time, MDIO data output valid after MDCLK high 10 8 td(MDCLKH-MDIO) Delay time, MDCLK high to MDIO Hi-Z 10 ns 300 ns 1 MDCLK 7 7 6 8 MDIO (Ouput) Figure 11-50. MDIO Output Timing Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 293 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.19 Ten-Gigabit Ethernet (10GbE) Switch Subsystem The 3-port Ten Gigabit Ethernet Switch Subsystem (different from the Network Coprocessor integrated switch) includes a stand-alone EMAC switch subsystem and a 2-lane SerDes macro. The 2-lane macro enables only 2 external ports. It does not include any packet acceleration or security acceleration engine. 11.19.1 10GbE Supported Features The key features of the 10GbE module are listed below: • 10 Gbps EMAC switch subsystem – MDIO: Media-dependent input/output module – SGMII Interface for 10/100/1000 and 10GBASE-KR for 10G – Ethernet switch with wire-rate switching (only two external ports are supported by the SerDes) – CPTS module that supports time-stamping for IEEE 1588v2 with support for eight hardware push events and generation of compare output pulses – Supports XFI electrical interface • CPDMA The CPDMA component provides CPPI 4.2 compatible functionality, and provides a 128-bit-wide data path to the TeraNet, enabling: • Support for 8 transmit channel and 16 receive channels • Support for reset isolation option For more information, see the KeyStone II Architecture 10 Gigabit Ethernet Subsystem User's Guide. 11.20 Timers The timers can be used to time events, count events, generate pulses, interrupt the CorePacs, and send synchronization events to the EDMA3 channel controller. 11.20.1 Timers Device-Specific Information The 66AK2Hxx device has up to twenty 64-bit timers in total, (66AK2H12 has 20 timers and the 66AK2H06 has 14) of which Timer0 through Timer3 (66AK2H06) or Timer7 (66AK2H12) are dedicated to each of the up to eight C66x CorePacs as watchdog timers and can also be used as general-purpose timers. Timer16 and Timer17 (66AK2H06) or (66AK2H12).Timer16 through Timer19 are dedicated to each of the Cortex-A15 processor cores as a watchdog timer and can also be used as general-purpose timers. The remaining timers can be configured as general-purpose timers only, with each timer programmed as a 64-bit timer or as two separate 32-bit timers. When operating in 64-bit mode, the timer counts either module clock cycles or input (TINPLx) pulses (rising edge) and generates an output pulse/waveform (TOUTLx) plus an internal event (TINTLx) on a software-programmable period. When operating in 32-bit mode, the timer is split into two independent 32bit timers. Each timer is made up of two 32-bit counters: a high counter and a low counter. The timer pins, TINPLx and TOUTLx are connected to the low counter. The timer pins, TINPHx and TOUTHx are connected to the high counter. The module clock for each timer module is SYSCLK1, with a shared local divider (not programmable) of /6 (timer module clock frequency = SYSCLK1/6). Refer to Table 11-13. When operating in watchdog mode, the timer counts down to 0 and generates an event. It is a requirement that software writes to the timer before the count expires, after which the count begins again. If the count ever reaches 0, the timer event output is asserted. Reset initiated by a watchdog timer can be set by programming the Reset Type Status register (RSTYPE) (see Section 11.5.2.6) and the type of reset initiated can set by programming the Reset Configuration register (RSTCFG) (see Section 11.5.2.8). For more information, see the KeyStone Architecture Timer 64P User's Guide. 11.20.2 Timers Electrical Data and Timing Table 11-51 and Table 11-52 list timing requirements and switching characteristics of the timers. 294 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-51. Timer Input Timing Requirements (1) (see Figure 11-51) NO. 1 2 (1) MIN MAX UNIT tw(TINPH) Pulse duration, high 12C ns tw(TINPL) Pulse duration, low 12C ns C = 1/SYSCLK1 clock frequency in ns Table 11-52. Timer Output Switching Characteristics (1) (see Figure 11-51) NO. PARAMETER MIN MAX UNIT 3 tw(TOUTH) Pulse duration, high 12C – 3 ns 4 tw(TOUTL) Pulse duration, low 12C – 3 ns (1) C = 1/SYSCLK1 clock frequency in ns. 1 2 TIMIx 3 4 TIMOx Figure 11-51. Timer Timing 11.21 Serial RapidIO (SRIO) Port The SRIO port on the device is a high-performance, low pin-count SerDes interconnect. SRIO interconnects in a baseband board design provide connectivity and control among the components. The device supports four 1× Serial RapidIO links or one 4× Serial RapidIO link. The SRIO interface is designed to operate at a data rate of up to 5 Gbps per differential pair. This equals 20 raw GBaud/s for the 4× SRIO port, or approximately 15 Gbps data throughput rate. The PHY part of the SRIO consists of the physical layer and includes the input and output buffers (each serial link consists of a differential pair), the 8-bit/10-bit encoder/decoder, the PLL clock recovery, and the parallel-to-serial/serial-to-parallel converters. For more information, see the KeyStone Architecture Serial RapidIO (SRIO) User's Guide. 11.21.1 Serial RapidIO Device-Specific Information The approach to specifying interface timing for the SRIO Port is different from other interfaces. For these other interfaces, the device timing was specified in terms of data manual specifications and I/O buffer information specification (IBIS) models. The Serial RapidIO peripheral is a master peripheral in the device. It conforms to the RapidIO™ Interconnect Specification, Part VI: Physical Layer 1×/4× LP-Serial Specification, Revision 1.3. For the SRIO port, Texas Instruments provides a PCB solution showing two TI SRIO-enabled DSPs connected together via a 4× SRIO link. TI has performed the simulation and system characterization to ensure all SRIO interface timings in this solution are met. NOTE TI supports only designs that follow the board design guidelines outlined in the RapidIO™ Interconnect Specification, Part VI: Physical Layer 1×/4× LP-Serial Specification, Revision 1.3. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 295 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.22 General-Purpose Input/Output (GPIO) 11.22.1 GPIO Device-Specific Information The GPIO peripheral pins are used for general-purpose input/output for the device. These pins are also used to configure the device at boot time. For more detailed information on device/ and peripheral configuration and the 66AK2Hxx device pin multiplexing, see Section 10.2. These GPIO pins can also be used to generate individual core interrupts (no support of bank interrupt) and EDMA events. 11.22.2 GPIO Peripheral Register Description Table 11-53 lists the GPIO registers. Table 11-53. GPIO Registers HEX ADDRESS OFFSETS ACRONYM REGISTER NAME 0x0008 BINTEN GPIO interrupt per bank enable register 0x000C - Reserved 0x0010 DIR GPIO Direction Register 0x0014 OUT_DATA GPIO Output Data Register 0x0018 SET_DATA GPIO Set Data Register 0x001C CLR_DATA GPIO Clear Data Register 0x0020 IN_DATA GPIO Input Data Register 0x0024 SET_RIS_TRIG GPIO Set Rising Edge Interrupt Register 0x0028 CLR_RIS_TRIG GPIO Clear Rising Edge Interrupt Register 0x002C SET_FAL_TRIG GPIO Set Falling Edge Interrupt Register 0x0030 CLR_FAL_TRIG GPIO Clear Falling Edge Interrupt Register 0x008C - Reserved 0x0090 – 0x03FF - Reserved 11.22.3 GPIO Electrical Data and Timing The GPIO input timing requirements are shown in Table 11-54 and the GPIO output switching characteristics are shown in Table 11-55. Table 11-54. GPIO Input Timing Requirements (1) (see Figure 11-52) NO. 1 2 (1) MIN MAX UNIT tw(GPOH) Pulse duration, GPOx high 12C ns tw(GPOL) Pulse duration, GPOx low 12C ns C = 1/SYSCLK1 clock frequency in ns Table 11-55. GPIO Output Switching Characteristics (1) (see Figure 11-52) NO. PARAMETER MIN MAX UNIT 3 tw(GPOH) Pulse duration, GPOx high 36C – 8 ns 4 tw(GPOL) Pulse duration, GPOx low 36C – 8 ns (1) 296 C = 1/SYSCLK1 clock frequency in ns 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 1 2 GPIx 3 4 GPOx Figure 11-52. GPIO Timing 11.23 Semaphore2 The device contains an enhanced Semaphore module for the management of shared resources of the SoC. The Semaphore enforces atomic accesses to shared chip-level resources so that the read-modifywrite sequence is not broken. The Semaphore module has unique interrupts to each of the CorePacs to identify when that CorePac has acquired the resource. Semaphore resources within the module are not tied to specific hardware resources. It is a software requirement to allocate semaphore resources to the hardware resources to be arbitrated. The Semaphore module supports all the CPUs in the device—12 for 66AK2H14 and 66AK2H12 devices, and 6 for 66AK2H06 devices—and contains 64 semaphores that can be shared within the system. There are two methods of accessing a semaphore resource: • Direct Access: A C66x CorePac directly accesses a semaphore resource. If free, the semaphore is granted. If not free, the semaphore is not granted. • Indirect Access: A C66x CorePac indirectly accesses a semaphore resource by writing to it. Once the resource is free, an interrupt notifies the C66x CorePac that the resource is available. 11.24 Universal Serial Bus 3.0 (USB 3.0) The device includes a USB 3.0 controller providing the following capabilities: • Support of USB 3.0 peripheral (or device) mode at the following speeds: – Super Speed (SS) (5 Gbps) – High Speed (HS) (480 Mbps) – Full Speed (FS) (12 Mbps) • Support of USB 3.0 host mode at the following speeds: – Super Speed (SS) (5 Gbps) – High Speed (HS) (480 Mbps) – Full Speed (FS) (12 Mbps) – Low Speed (LS) (1.5 Mbps) • Integrated DMA controller with extensible Host Controller Interface (xHCI) support • Support for 14 transmit and 14 receive endpoints plus control EP0 For more information, see the KeyStone II Architecture Universal Serial Bus 3.0 (USB 3.0) User's Guide. 11.25 EMIF16 Peripheral The EMIF16 module provides an interface between the device and external memories such as NAND and NOR flash. For more information, see the KeyStone Architecture External Memory Interface (EMIF16) User's Guide. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 297 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.25.1 EMIF16 Electrical Data and Timing EMIF16 asynchronous memory timing requirements are shown in Table 11-56. Table 11-56. EMIF16 Asynchronous Memory Timing Requirements (1) (see Figure 11-53, Figure 11-54, Figure 11-55, and Figure 11-56) NO. MIN MAX UNIT General Timing 2 tw(WAIT) Pulse duration, WAIT assertion and deassertion minimum time 2E ns 28 td(WAIT-WEH) Setup time, WAIT asserted before WE high 4E + 3 ns 14 td(WAIT-OEH) Setup time, WAIT asserted before OE high 4E + 3 ns Read Timing 3 tC(CEL) EMIF read cycle time when ew = 0, meaning not in extended wait mode (RS+RST+RH+3) (RS+RST+RH+3) *E-3 *E+3 ns tC(CEL) EMIF read cycle time when ew =1, meaning extended wait mode enabled (RS+RST+RH+3) (RS+RST+RH+3) *E-3 *E+3 ns tosu(CEL-OEL) Output setup time from CE low to OE low. SS = 0, not in select strobe mode (RS+1) × E – 3 (RS+1) × E + 3 toh(OEH-CEH) Output hold time from OE high to CE high. SS = 0, not in select strobe mode (RH+1) × E – 3 (RH+1) × E + 3 tosu(CEL-OEL) Output setup time from CE low to OE low in select strobe mode, SS = 1 (RS+1) × E – 3 (RS+1) × E + 3 toh(OEH-CEH) Output hold time from OE high to CE high in select strobe mode, SS = 1 (RH+1) × E – 3 (RH+1) × E + 3 6 tosu(BAV-OEL) Output setup time from BA valid to OE low (RS+1) × E – 3 (RS+1) × E + 3 ns 7 toh(OEH-BAIV) Output hold time from OE high to BA invalid (RH+1) × E – 3 (RH+1) × E + 3 ns 8 tosu(AV-OEL) Output setup time from A valid to OE low (RS+1) × E – 3 (RS+1) × E + 3 ns 9 toh(OEH-AIV) Output hold time from OE high to A invalid (RH+1) × E – 3 (RH+1) × E + 3 ns 10 tw(OEL) OE active time low, when ew = 0. Extended wait mode is disabled. (RST+1) × E – 3 (RST+1) × E + 3 ns 10 tw(OEL) OE active time low, when ew = 1. Extended wait mode is enabled. (RST+1) × E – 3 (RST+1) × E + 3 ns 11 td(WAITH-OEH) Delay time from WAIT deasserted to OE# high 4E + 3 ns 12 tsu(D-OEH) Input setup time from D valid to OE high 3 ns 13 th(OEH-D) Input hold time from OE high to D invalid 0.5 ns 3 4 5 4 5 ns ns ns ns Write Timing 15 tc(CEL) EMIF write cycle time when ew = 0, meaning not in extended wait mode (WS+WST+WH+ TA+4)*E-3 (WS+WST+WH+ TA+4)*E+3 ns tc(CEL) EMIF write cycle time when ew =1., meaning extended wait mode is enabled (WS+WST+WH+ TA+4)*E-3 (WS+WST+WH+ TA+4)*E+3 ns tosuCEL-WEL) Output setup time from CE low to WE low. SS = 0, not in select strobe mode (WS+1) × E – 3 toh(WEH-CEH) Output hold time from WE high to CE high. SS = 0, not in select strobe mode (WH+1) × E – 3 tosuCEL-WEL) Output setup time from CE low to WE low in select strobe mode, SS = 1 (WS+1) × E – 3 toh(WEH-CEH) Output hold time from WE high to CE high in select strobe mode, SS = 1 (WH+1) × E – 3 18 tosu(RNW-WEL) Output setup time from RNW valid to WE low (WS+1) × E – 3 ns 19 toh(WEH-RNW) Output hold time from WE high to RNW invalid (WH+1) × E – 3 ns 20 tosu(BAV-WEL) Output setup time from BA valid to WE low (WS+1) × E – 3 ns 21 toh(WEH-BAIV) Output hold time from WE high to BA invalid (WH+1) × E – 3 ns 22 tosu(AV-WEL) Output setup time from A valid to WE low (WS+1) × E – 3 ns 23 toh(WEH-AIV) Output hold time from WE high to A invalid (WH+1) × E – 3 ns 24 tw(WEL) WE active time low, when ew = 0. Extended wait mode is disabled. (WST+1) × E – 3 ns 24 tw(WEL) WE active time low, when ew = 1. Extended wait mode is enabled. (WST+1) × E – 3 ns 26 tosu(DV-WEL) Output setup time from D valid to WE low (WS+1) × E – 3 ns 27 toh(WEH-DIV) Output hold time from WE high to D invalid (WH+1) × E – 3 25 td(WAITH-WEH) Delay time from WAIT deasserted to WE# high 15 16 17 16 17 (1) 298 ns ns ns ns ns 4E + 3 ns E = 1/(SYSCLK1/6) 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 3 EM_CE[3:0] EM_R/W EM_BA[1:0] EM_A[21:0] 5 7 9 4 6 8 10 EM_OE 13 12 EM_D[15:0] EM_WE Figure 11-53. EMIF16 Asynchronous Memory Read Timing Diagram 15 EM_CE[3:0] EM_R/W EM_BA[1:0] EM_A[21:0] 17 19 21 23 16 18 20 22 24 EM_WE 26 27 EM_D[15:0] EM_OE Figure 11-54. EMIF16 Asynchronous Memory Write Timing Diagram Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 299 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Setup www.ti.com Extended Due to EM_WAIT Strobe Strobe Hold EM_CE[3:0] EM_BA[1:0] EM_A[21:0] EM_D[15:0] EM_OE 14 11 EM_WAIT 2 2 Asserted Deasserted Figure 11-55. EMIF16 EM_WAIT Read Timing Diagram Setup Extended Due to EM_WAIT Strobe Strobe Hold EM_CE[3:0] EM_BA[1:0] EM_A[21:0] EM_D[15:0] EM_WE 28 25 EM_WAIT 2 2 Asserted Deasserted Figure 11-56. EMIF16 EM_WAIT Write Timing Diagram 11.26 Emulation Features and Capability The debug capabilities of KeyStone II devices include the Debug subsystem module (DEBUGSS). The DEBUGSS module contains the ICEPick module which handles the external JTAG Test Access Port (TAP) and multiple secondary TAPs for the various processing cores of the device. It also provides Debug Access Port (DAP) for system wide memory access from debugger, Cross triggering, System trace, Peripheral suspend generation, Debug port (EMUx) pin management, and so forth. The DEBUGSS module works in conjunction with the debug capability integrated in the processing cores (ARM and DSP subsystems) to provide a comprehensive hardware platform for a rich debug and development experience. 11.26.1 Chip-Level Features • • 300 Support for 1149.1(JTAG and Boundary scan) and 1149.6 (Boundary scan extensions). Trace sources to DEBUG SubSystem System Trace Module (DEBUGSS STM) – Provides a way for hardware instrumentation and software messaging to supplement the processor core trace mechanisms. – Hardware instrumentation support of CPTracers to support logging of bus transactions for critical endpoints – Software messaging/instrumentation support for SoC and QMSS PDSP cores through DEBUGSS STM. 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com • • • • • • • • • SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Trace Sinks – Support for trace export (from all processor cores and DEBUGSS STM) through emulation pins. Concurrent trace of DSP and STM traces or ARM and STM traces via EMU pins is possible. Concurrent trace export of DSP and ARM is not possible via EMU pins. – Support for 32KB DEBUGSS TBR (Trace Buffer and Router) to hold system trace. The data can be drained using EDMA to on-chip or DDR memory buffers. These intermediate buffers can subsequently be drained through the device high speed interfaces. The DEBUGSS TBR is dedicated to the DEBUGSS STM module. The trace draining interface used in KeyStone II for DEBUGSS and ARMSS are based on the new CT-TBR. Cross triggering: Provides a way to propagate debug (trigger) events from one processor/subsystem/module to another – Cross triggering between multiple devices via EMU0/EMU1 pins – Cross triggering between multiple processing cores within the device like ARM/DSP Cores and nonprocessor entities like ARM STM (input only), CPTracers, CT-TBRs and DEBUGSS STM (input only) Synchronized starting and stopping of processing cores – Global start of all DSP cores – Global stopping of all ARM and DSP cores Emulation mode aware peripherals (suspend features and debug access features) Support system memory access via the DAP port (natively support 32-bit address, and it can support 36-bit address through configuration of MPAX inside MSMC). Debug access to any invalid memory location (reserved/clock-gated/power-down) does not cause system hang. Scan access to secondary TAPs of DEBUGSS is disabled in Secure devices by default. Security override sequence is supported (requires software override sequence) to enable debug in secure devices. In addition, Debug features of the ARM cores are blockable through the ARM debug authentication interface in secure devices. Support WIR (wait-in-reset) debug boot mode for nonsecure devices. Debug functionality survives all pin resets except power-on resets (POR/RESETFULL) and test reset (TRST). PDSP Debug features like access/control through DAP, Halt mode debug and software instrumentation. 11.26.1.1 ARM Subsystem Features • • • • • • • • • • • Support for invasive debug like halt mode debugging (breakpoint, watchpoints) and monitor mode debugging Support for noninvasive debugging (program trace, performance monitoring) Support for A15 Performance Monitoring Unit (cycle counters) Support for per core CoreSight Program Trace Module (CS-PTM) with timing Support for an integrated CoreSight System Trace Module (CS-STM) for hardware event and software instrumentation A shared timestamp counter for all ARM cores and STM is integrated in ARMSS for trace data correlation Support for a 16KB Trace Buffer and Router (TBR) to hold PTM/STM trace. The trace data is copied by EDMA to external memory for draining by device high speed serial interfaces. Support for simultaneous draining of trace stream through EMUn pins and TBR (to achieve higher aggregate trace throughput) Support for debug authentication interface to disable debug accesses in secure devices Support for cross triggering between MPU cores, CS-STM and CT-TBR Support for debug through warm reset Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 301 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.26.1.2 DSP Features • • • • • • • • • Support for Halt-mode debug Support for Real-time debug Support for Monitor mode debug Advanced Event Triggering (AET) for data/PC watch-points, event monitoring and visibility into external events Support for PC/Timing/Data/Event trace. TETB (TI Embedded Trace Buffer) of 4KB to store PC/Timing/Data/Event trace. The trace data is copied by EDMA to external memory for draining by device high speed serial interfaces or it can be drained through EMUx pins Support for Cross triggering source/sink to other C66x CorePacs and device subsystems. Using Advanced Event Triggering to Find and Fix Intermittent Real-Time Bugs application report Using Advanced Event Triggering to Debug Real-Time Problems in High Speed Embedded Microprocessor Systems application report For more information on the AET, see the following documents: • Using Advanced Event Triggering to Find and Fix Intermittent Real-Time Bugs • Using Advanced Event Triggering to Debug Real-Time Problems in High Speed Embedded Microprocessor Systems 11.26.2 ICEPick Module The debugger is connected to the device through its external JTAG interface. The first level of debug interface seen by the debugger is connected to the ICEPick module embedded in the DEBUGSS. ICEPick is the chip-level TAP, responsible for providing access to the IEEE 1149.1 and IEEE 1149.6 boundary scan capabilities of the device. The device has multiple processors, some with secondary JTAG TAPs (C66x CorePacs) and others with an APB memory mapped interface (ARM CorePac and Coresight components). ICEPick manages the TAPs as well as the power/reset/clock controls for the logic associated with the TAPs as well as the logic associated with the APB ports. ICEPick provides the following debug capabilities: • Debug connect logic for enabling or disabling most ICEPick instructions • Dynamic TAP insertion – Serially linking up to 32 TAP controllers – Individually selecting one or more of the TAPS for scan without disrupting the instruction register (IR) state of other TAPs • Power, reset and clock management – Provides the power and clock status of the domain to the debugger – Provides debugger control of the power domain of a processor. • Force the domain power and clocks on • Prohibit the domain from being clock-gated or powered down – Applies system reset – Provides wait-in-reset (WIR) boot mode – Provides global and local WIR release – Provides global and local reset block The ICEPick module implements a connect register, which must be configured with a predefined key to enable the full set of JTAG instructions. Once the debug connect key has been properly programmed, ICEPick signals and subsystems emulation logic should be turned on. 302 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.26.2.1 ICEPick Dynamic Tap Insertion To include more or fewer secondary TAPS in the scan chain, the debugger must use the ICEPick TAP router to program the TAPs. At its root, ICEPick is a scan-path linker that lets the debugger selectively choose which subsystem TAPs are accessible through the device-level debug interface. Each secondary TAP can be dynamically included in or excluded from the scan path. From external JTAG interface point of view, secondary TAPS that are not selected appear not to exist. There are two types of components connected through ICEPick to the external • Legacy JTAG Components — C66x implements a JTAG-compatible port with ICEPick and individually attached to an ICEPick secondary TAP. • CoreSight Components — The CoreSight components are interfaced CS_DAP module. The CS_DAP is attached to the ICEPick secondary transactions into APBv3 transactions. debug interface: and are directly interfaced with ICEPick through the TAP and translates JTAG Table 11-57 shows the ICEPick secondary taps in the system. For more details on the test related P1500 TAPs, see the DFTSS specification. Table 11-57. ICEPick Debug Secondary TAPs TAP # TYPE NAME ACCESS IN IR SCAN SECURE LENGTH DEVICE 0 n/a n/a n/a No Reserved (This is an internal TAP and not exposed at the DEBUGSS boundary) 1 JTAG C66x CorePac0 38 No C66x CorePac0 2 JTAG C66x CorePac1 38 No C66x CorePac1 3 JTAG C66x CorePac2 38 No C66x CorePac2 4 JTAG C66x CorePac3 38 No C66x CorePac3 5 JTAG C66x CorePac4 38 No C66x CorePac4 (66AK2H12/14 only) 6 JTAG C66x CorePac5 38 No C66x CorePac5 (66AK2H12/14 only) 7 JTAG C66x CorePac6 38 No C66x CorePac6 (66AK2H12/14 only) 8 JTAG C66x CorePac7 38 No C66x CorePac7 (66AK2H12/14 only) 9..13 JTAG Reserved NA No Spare ports for future expansion 14 CS CS_DAP (APB-AP) 4 No ARM A15 Cores (This is an internal TAP and not exposed at the DEBUGSS boundary) CS_DAP (AHB-AP) DESCRIPTION PDSP Cores (This is an internal TAP and not exposed at the DEBUGSS boundary) For more information on ICEPick, see the KeyStone II Architecture Debug and Trace User’s Guide. 11.27 Debug Port (EMUx) The device also supports 34 emulation pins — EMU[33:0], which includes 19 dedicated EMU pins and 15 pins multiplexed with GPIO. These pins are shared by A15/DSP/STM trace, cross triggering, and debug boot modes as shown in Table 11-61. The 34-pin dedicated emulation interface is also defined in the following table. NOTE If EMU[1:0] signals are shared for cross-triggering purposes in the board level, they should not be used for trace purposes. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 303 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Table 11-58. Emulation Interface with Different Debug Port Configurations CROSS EMU PINS TRIGGERING ARM TRACE DSP TRACE DEBUG BOOT MODE STM EMU33 TRCDTa[29] TRCDTb[31] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or Hi-ZTRCCLK, or Hi-Z EMU32 TRCDTa[28] TRCDTb[30] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU31 TRCDTa[27] TRCDTb[29] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU30 TRCDTa[26] TRCDTb[28] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU29 TRCDTa[25] TRCDTb[27] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU28 TRCDTa[24] TRCDTb[26] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU27 TRCDTa[23] TRCDTb[25] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU26 TRCDTa[22] TRCDTb[24] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU25 TRCDTa[21] TRCDTb[23] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU24 TRCDTa[20] TRCDTb[22] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU23 TRCDTa[19] TRCDTb[21] TRCDTa[19] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU22 TRCDTa[18] TRCDTb[20] TRCDTa[18] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU21 TRCDTa[17] TRCDTb[19] TRCDTa[17] TRCDTb[19] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU20 TRCDTa[16] TRCDTb[18] TRCDTa[16] TRCDTb[18] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU19 TRCDTa[15] TRCDTb[17] TRCDTa[15] TRCDTb[17] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU18 TRCDTa[14] TRCDTb[16] TRCDTa[14] TRCDTb[16] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU17 TRCDTa[13] TRCDTb[15] TRCDTa[13] TRCDTb[15] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU16 TRCDTa[12] TRCDTb[14] TRCDTa[12] TRCDTb[14] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU15 TRCDTa[11] TRCDTb[13] TRCDTa[11] TRCDTb[13] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU14 TRCDTa[10] TRCDTb[12] TRCDTa[10] TRCDTb[12] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU13 TRCDTa[9] TRCDTb[11] TRCDTa[9] TRCDTb[11] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU12 TRCDTa[8] TRCDTb[10] TRCDTa[8] TRCDTb[10] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU11 TRCDTa[7] TRCDTb[9] TRCDTa[7] TRCDTb[9] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU10 TRCDTa[6] TRCDTb[8] TRCDTa[6] TRCDTb[8] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU9 TRCDTa[5] TRCDTb[7] TRCDTa[5] TRCDTb[7] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU8 TRCDTa[4] TRCDTb[6] TRCDTa[4] TRCDTb[6] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU7 TRCDTa[3] TRCDTb[5] TRCDTa[3] TRCDTb[5] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU6 TRCDTa[2] TRCDTb[4] TRCDTa[2] TRCDTb[4] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU5 TRCDTa[1] TRCDTb[3] TRCDTa[1] TRCDTb[3] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU4 TRCDTa[0] TRCDTb[2] TRCDTa[0] TRCDTb[2] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z 304 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-58. Emulation Interface with Different Debug Port Configurations (continued) CROSS EMU PINS TRIGGERING ARM TRACE DSP TRACE DEBUG BOOT MODE STM EMU3 TRCCTRL TRCCTRL TRCCLKB TRCCLKB TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU2 TRCCLK TRCCLK TRCCLKA TRCCLKA TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z EMU1 Trigger1 TRCDTb[1] TRCDTb[1] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z dbgbootmode[1] EMU0 Trigger0 TRCDTb[0] TRCDTb[0] TRCDT3, or TRCDT2, or TRCDT1, or TRCDT0, or TRCCLK, or Hi-Z dbgbootmode[0] Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 305 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.27.1 Concurrent Use of Debug Port The following combinations are possible concurrently: • Trigger 0/1 • Trigger 0/1 and STM Trace (up to 4 data pins) • Trigger 0/1 and STM Trace (up to 4 data pins) and C66x Trace (up to 20 data pins) • Trigger 0/1 and STM Trace (1-4 data pins) and ARM Trace (27-24 data pins) • STM Trace (1-4 data pins) and ARM Trace (29-26 data pins) • Trigger 0/1 and ARM Trace (up to 29 data pins) • ARM Trace (up to 32 data pins) ARM and DSP simultaneous trace is not supported. 11.27.2 Master ID for Hardware and Software Messages Table 11-59 and Table 11-60 describe the master ID for the various hardware and software masters of the STM. Table 11-59. MSTID Mapping for Hardware Instrumentation (CPTRACERS) CPTRACER NAME MSTID [7:0] CLOCK DOMAIN SID[4:0] DESCRIPTION CPT_MSMCx_MST, where x = 0..3 0x94-0x97 SYSCLK1/1 0x0..3 MSMC SRAM Bank 0 to MSMC SRAM Bank 3 monitors CPT_MSMC4_MST 0xB1 SYSCLK1/1 0x4 MSMC SRAM Bank 4 CPT_MSMCx_MST, where x = 5..7 0xAE – 0xB0 SYSCLK1/1 0x5..7 MSMC SRAM Bank 5to MSMC SRAM Bank 7 monitors CPT_DDR3A_MST 0x98 SYSCLK1/1 0x8 MSMC DDR3A port monitor CPT_L2_x_MST, where x = 0..7 0x8C – 0x93 SYSCLK1/3 0x9..0x10 DSP 0 to 7 SDMA port monitors CPT_TPCC0_4_MST 0xA4 SYSCLK1/3 0x11 EDMA 0 and EDMA 4 CFG port monitor CPT_TPCC1_2_3_MST 0xA5 SYSCLK1/3 0x12 EDMA 1, EDMA2 and EDMA3 CFG port monitor CPT_INTC_MST 0xA6 SYSCLK1/3 0x13 INTC port monitor (for INTC 0/1/2 and GIC400) CPT_SM_MST 0x99 SYSCLK1/3 0x14 Semaphore CFG port monitors CPT_QM_CFG1_MST 0x9A SYSCLK1/3 0x15 QMSS CFG1 port monitor CPT_QM_CFG2_MST 0xA0 SYSCLK1/3 0x16 QMSS CFG2 port monitor CPT_QM_M_MST 0x9B SYSCLK1/3 0x17 QM_M CFG/DMA port monitor CPT_SPI_ROM_EMIF16_MST 0xA7 SYSCLK1/3 0x18 SPI ROM EMIF16 CFG port monitor CPT_CFG_MST 0x9C SYSCLK1/3 0x19 SCR_3P_B and SCR_6P_B CFG peripheral port monitors Reserved 0x1A Reserved Reserved 0x1B Reserved Reserved 0x1C Reserved Reserved 0x1D Reserved Reserved 0x1E Reserved 0x1F DDR 3B port monitor (on SCR 3C) CPT_DDR3B_MST 0xA1 SYSCLK1/3 Table 11-60. MSTID Mapping for Software Messages CORE NAME MSTID [7:0] DESCRIPTION C66x CorePac0 0x0 C66x CorePac MDMA Master ID C66x CorePac1 0x1 C66x CorePac MDMA Master ID C66x CorePac2 0x2 C66x CorePac MDMA Master ID C66x CorePac3 0x3 C66x CorePac MDMA Master ID C66x CorePac4 0x4 (66AK2H14/12 only) 306 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-60. MSTID Mapping for Software Messages (continued) CORE NAME MSTID [7:0] DESCRIPTION C66x CorePac5 0x5 (66AK2H14/12 only) C66x CorePac6 0x6 (66AK2H14/12 only) C66x CorePac7 0x7 (66AK2H14/12 only) A15 Core0 0x8 ARM Master IDs A15 Core1 0x9 ARM Master ID A15 Core2 0xA ARM Master ID A15 Core3 0xB ARM Master ID QMSS PDSPs 0x46 All QMSS PDSPs share the same master ID. Differentiating between the 8 PDSPs is done through the channel number used 11.27.3 SoC Cross-Triggering Connection The cross-trigger lines are shared by all the subsystems implementing cross-triggering. An MPU subsystem trigger event can therefore be propagated to any application subsystem or system trace component. The remote subsystem or system trace component can be programmed to be sensitive to the global SOC trigger lines to either: • Generate a processor debug request • Generate an interrupt request • Start/Stop processor trace • Start/Stop CBA transaction tracing through CPTracers • Start external logic analyzer trace • Stop external logic analyzer trace Table 11-61 describes the cross-triggering connection. Table 11-61. Cross-Triggering Connection NAME SOURCE TRIGGERS SINK TRIGGERS Device-to-device trigger via EMU0/1 pins YES YES This is fixed (not affected by configuration) MIPI-STM NO YES Trigger input only for MIPI-STM in DebugSS CT-TBR YES YES DEBUGSS CT-TBR CS-TPIU NO YES DEBUGSS CS-TPIU COMMENTS Inside DEBUGSS Outside DEBUGSS DSPSS YES YES CP_Tracers YES YES ARM YES YES ARM Cores, ARM CS-STM and ARM CTTBR Table 11-62 describes the crosstrigger connection between various cross trigger sources and TI XTRIG module. Table 11-62. TI XTRIG Assignment NAME ASSIGNED XTRIG CHANNEL NUMBER C66x CorePac0-3 (66AK2H06 only) XTRIG 0-3 (66AK2H06 only) C66x CorePac0-7 (66AK2H12/14 only) XTRIG 0-7 (66AK2H12/14 only) CPTracer 0..31 (The CPTracer number refers to the SID[4:0] as shown in Table 11-59 XTRIG 8 .. 39 Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 307 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.27.4 Peripherals-Related Debug Requirement Table 11-63 lists all the peripherals on this device, and the status of whether or not it supports emulation suspend or emulation request events. The DEBUGSS supports up to 32 debug suspend sources (processor cores) and 64 debug suspend sinks (peripherals). The assignment of peripherals is shown in Table 11-64 and the assignment of processor cores is shown in Table 11-65. By default the logical AND of all the processor cores is routed to the peripherals. It is possible to select an individual core to be routed to the peripheral (For example: used in tightly coupled peripherals like timers), a logical AND of all cores (Global peripherals) or a logical OR of all cores by programming the DEBUGSS.DRM module. The SOFT bit should be programmed based on whether or not an immediate pause of the peripheral function is required or if the peripheral suspend should occur only after a particular completion point is reached in the normal peripheral operation. The FREE bit should be programmed to enable or disable the emulation suspend functionality. Table 11-63. Peripherals Emulation Support EMULATION SUSPEND SUPPORT PERIPHERAL STOPMODE REAL-TIME MODE FREE BIT STOP BIT EMULATION REQUEST SUPPORT (cemudbg/emudbg) DEBUG PERIPHERAL ASSIGNMENT Infrastructure Peripherals EDMA_x, where X=0/1/2/3/4 N N N N Y NA Y (CPDMA only) Y (CPDMA only) Y (CPDMA only) Y (CPDMA only) Y 20 CP_Tracers_X, where X = 0..32 N N N N N NA MPU_X, where X = 0..11 N N N N Y NA CP_INTC N N N N Y NA BOOT_CFG N N N N Y NA SEC_MGR N N N N Y NA PSC N N N N N NA PLL N N N N N NA TIMERx, x=0, 1..7, 8..19 Y N Y Y N 0, 1..7, 8..19 Semaphore N N N N Y NA GPIO N N N N N NA QM_SS Memory Controller Peripherals DDR3A/B N N N N Y NA MSMC N N N N Y NA EMIF16 N N N N Y NA I2C_X, where X = 0/1/2 Y N Y Y Y 21/22/23 SPI_X, where X = 0/1/2 N N N N Y NA UART_X, where X = 0/1 Y N Y Y Y 24/25 Serial Interfaces High Speed Serial Interfaces Hyperlink_0/1 N N N N Y PCIeSS 0 N N N N N SRIO / NetCP_1 Y Y Y Y (Soft Only) Y 26 NetCP (ethernet switch) Y Y Y Y N 27 10GbE (ethernet switch) (1) Y N Y Y N 29 (1) 308 66AK2H14 only 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Table 11-63. Peripherals Emulation Support (continued) EMULATION SUSPEND SUPPORT PERIPHERAL STOPMODE REAL-TIME MODE FREE BIT STOP BIT EMULATION REQUEST SUPPORT (cemudbg/emudbg) N N N N N USBSS DEBUG PERIPHERAL ASSIGNMENT NA Based on Table 11-63, the number of suspend interfaces in Keystone II devices is listed in Table 11-64. Table 11-64. EMUSUSP Peripheral Summary (for EMUSUSP handshake from DEBUGSS) INTERFACES NUM_SUSPEND_PERIPHERALS EMUSUSP Interfaces 54 EMUSUSP Realtime Interfaces 15 Table 11-65 summarizes the DEBUG core assignment. Emulation suspend output of all the cores are synchronized to SYSCLK1/6 which is frequency of the slowest peripheral that uses these signals. Table 11-65. EMUSUSP Core Summary (for EMUSUSP handshake to DEBUGSS) CORE # ASSIGNMENT 0..7 C66x CorePac0..7 8..11 ARM CorePac 8..11 0..7 C66x CorePac0..3 C66x CorePac4.,7 (66AK2H12/14 only) 12..29 Reserved 30 Logical OR of Core# 0..11 31 Logical AND of Core #0..11 11.27.5 Advanced Event Triggering (AET) The device supports advanced event triggering (AET). This capability can be used to debug complex problems as well as understand performance characteristics of user applications. AET provides the following capabilities: • Hardware program breakpoints: specify addresses or address ranges that can generate events such as halting the processor or triggering the trace capture. • Data watchpoints: specify data variable addresses, address ranges, or data values that can generate events such as halting the processor or triggering the trace capture. • Counters: count the occurrence of an event or cycles for performance monitoring. • State sequencing: allows combinations of hardware program breakpoints and data watchpoints to precisely generate events for complex sequences. For more information on the AET, see the following documents: • Using Advanced Event Triggering to Find and Fix Intermittent Real-Time Bugs • Using Advanced Event Triggering to Debug Real-Time Problems in High Speed Embedded Microprocessor Systems 11.27.6 Trace The device supports trace. Trace is a debug technology that provides a detailed, historical account of application code execution, timing, and data accesses. Trace collects, compresses, and exports debug information for analysis. Trace works in real-time and does not impact the execution of the system. For more information on board design guidelines for trace advanced emulation, see the Emulation and Trace Headers Technical Reference Manual. Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 309 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 11.27.6.1 Trace Electrical Data and Timing The Trace switching characteristics are shown in Table 11-66. Table 11-66. Trace Switching Characteristics (see Figure 11-57) NO. PARAMETER MIN 1 tw(DPnH) Pulse duration, DPn/EMUn high 1 2 2 tw(DPnL)10% Pulse duration, DPn/EMUn low detected at 10% Voh 3 tsko(DPn) Output skew time, time delay difference between DPn/EMUn pins configured as trace tskp(DPn) Pulse skew, magnitude of difference between high-to-low (tphl) and low-tohigh (tplh) propagation delays. tsldp_o(DPn) Output slew rate DPn/EMUn MAX UNIT 2.4 ns tw(DPnH)90% Pulse duration, DPn/EMUn high detected at 90% Voh 1.5 ns tw(DPnL) 2.4 ns 1.5 ns Pulse duration, DPn/EMUn low -1 3.3 1 ns 600 ps V/ns A TPLH Buffer Inputs Buffers DP[n] / EMU[n] Pins B TPLH 1 2 B A 3 C C Figure 11-57. Trace Timing 11.27.7 IEEE 1149.1 JTAG The Joint Test Action Group (JTAG) interface is used to support boundary scan and emulation of the device. The boundary scan supported allows for an asynchronous test reset (TRST) and only the five baseline JTAG signals (for example, no EMU[1:0]) required for boundary scan. Most interfaces on the device follow the Boundary Scan Test Specification (IEEE 1149.1), while all of the SerDes (SGMII) support the AC-coupled net test defined in AC-Coupled Net Test Specification (IEEE 1149.6). It is expected that all compliant devices are connected through the same JTAG interface, in daisy-chain fashion, in accordance with the specification. The JTAG interface uses 1.8-V LVCMOS buffers, compliant with the Power Supply Voltage and Interface Standard for Nonterminated Digital Integrated Circuit Specification (EAI/JESD8-5). 11.27.7.1 IEEE 1149.1 JTAG Compatibility Statement For maximum reliability, the 66AK2Hxx device includes an internal pulldown (IPD) on the TRST pin to ensure that TRST will always be asserted upon power up and the device’s internal emulation logic will always be properly initialized when this pin is not routed out. JTAG controllers from Texas Instruments actively drive TRST high. However, some third-party JTAG controllers may not drive TRST high, but expect the use of an external pullup resistor on TRST. When using this type of JTAG controller, assert TRST to initialize the device after powerup and externally drive TRST high before attempting any emulation or boundary scan operations. 310 66AK2Hxx Peripheral Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 11.27.7.2 JTAG Electrical Data and Timing JTAG test port timing requirements are shown in Table 11-67 and JTAG test port switching characteristics are shown in Table 11-68. Table 11-67. JTAG Test Port Timing Requirements (see Figure 11-58) NO. MIN MAX UNIT 1 tc(TCK) Cycle time, TCK 23 ns 1a tw(TCKH) Pulse duration, TCK high (40% of tc) 9.2 ns 1b tw(TCKL) Pulse duration, TCK low (40% of tc) 9.2 ns 3 tsu(TDI-TCK) Input setup time, TDI valid to TCK high 2 ns 3 tsu(TMS-TCK) Input setup time, TMS valid to TCK high 2 ns 4 th(TCK-TDI) Input hold time, TDI valid from TCK high 10 ns 4 th(TCK-TMS) Input hold time, TMS valid from TCK high 10 ns Table 11-68. JTAG Test Port Switching Characteristics (see Figure 11-58) NO. 2 PARAMETER td(TCKL-TDOV) MIN Delay time, TCK low to TDO valid MAX UNIT 8.24 ns 1 1b 1a TCK 2 TDO 4 3 TDI / TMS Figure 11-58. JTAG Test-Port Timing Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2Hxx Peripheral Information 311 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 12 Device and Documentation Support 12.1 Device Nomenclature To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all devices and support tools. Each family member has one of two prefixes: X or [blank]. These prefixes represent evolutionary stages of product development from engineering prototypes through fully qualified production devices/tools. Device development evolutionary flow: • X: Experimental device that is not necessarily representative of the final device's electrical specifications • [Blank]: Fully qualified production device Support tool development evolutionary flow: • X: Development-support product that has not yet completed Texas Instruments internal qualification testing. • [Blank]: Fully qualified development-support product Experimental (X) and fully qualified [Blank] devices and development-support tools are shipped with the following disclaimer: Developmental product is intended for internal evaluation purposes. Fully qualified and production devices and development-support tools have been characterized fully, and the quality and reliability of the device have been demonstrated fully. TI's standard warranty applies. Predictions show that experimental devices (X) have a greater failure rate than the standard production devices. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used. TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type (for example, AAW), the temperature range (for example, blank is the default case temperature range), and the device speed range, in Megahertz (for example, blank is 1000 MHz [1 GHz]). For device part numbers and further ordering information for 66AK2Hxx in the AAW package type, see ti.com or contact your TI sales representative. Figure 12-1 provides a legend for reading the complete device name for any C66x+ DSP generation member. 312 Device and Documentation Support Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 ( _ ) 66A K2 H 12 PREFIX X = Experimental device Blank = Qualified device (_) ( _ ) AAW ( _ ) ( _ ) MAXIMUM DEVICE SPEED Blank = 1 GHz 2 = 1.2 GHz 24 = 1.2-GHz DSP / 1.4-GHz ARM DEVICE FAMILY 66A = DSP + ARM SoC TEMPERATURE RANGE Blank = Commercial temperature range (0°C to +85°C) A = Extended temperature range (–40°C to +100°C) ARCHITECTURE K2 = KeyStone II PACKAGE TYPE AAW = 1517-pin plastic ball grid array, with Pb-free solder balls and die bumps PLATFORM H SECURITY Blank = Security Accelerator disabled / General-Purpose device X = Security Accelerator enabled / General-Purpose device D = Security Accelerator enabled / High-Security device with TI developmental keys S = Security Accelerator enabled / High-Security device with production keys DEVICE NUMBER 6,12, or 14 SILICON REVISION Blank = Initial 1.0 silicon A = Silicon Revision 1.1 B = Silicon Revision 2.0 C = Silicon Revision 3.0 D = Silicon Revision 3.1 Figure 12-1. C66x DSP Device Nomenclature (Including the 66AK2Hxx Device) Device and Documentation Support Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 313 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 12.2 Tools and Software TI offers and extensive line of development tools. Tools and software to evaluate the performance of the device, generate code, and develop solutions are listed below. Models 66AK2H14 AAW BSDL Model BSDL model for the 66AK2H14 DSP. 66AK2H14 AAW IBIS Model IBIS model for the 66AK2H14 DSP. 66AK2H14 Power Consumption Model Power consumption summary spreadsheet for the 66AK2H14 DSP. 66AK2H12 66AK2H06 AAW BSDL Model BSDL model for the 66AK2H12 and 66AK2H06 DSPs. 66AK2H12 66AK2H06 AAW IBIS Model IBIS model for the 66AK2H12 and 66AK2H06 DSPs. 66AK2H12 Power Consumption Model Power consumption summary spreadsheet for the 66AK2H12 DSP. 66AK2H06 Power Consumption Model Power consumption summary spreadsheet for the 66AK2H06 DSP. 66AK2Hx FloTherm Model FloTherm model for the 66AK2Hx DSPs. Design Kits and Evaluation Modules TCI6636K2H Evaluation Module Enables developers to immediately start evaluating TCI6636K2H processor and begin building application around it especially those demanding highperformance computation like telecom infrastructures, wireless standards including WCDMA/HSPA/HSPA+, TD-SCDMA, GSM, TDD-LTE,FDD-LTE, and WiMAX. Software Medical Imaging Software Tool Kits (STK) Provides a collection of several standard ultrasound and optical coherence tomography (OCT) algorithms for TI’s C66x and C64x+ architecture. Multicore Video Infrastructure Demo for Multicore Software Development Kit (MCSDK) Provides highly-optimized platform and video software components and enables development of realtime video applications on C66x multicore devices. CODECS- Video, Speech - for C66x-based Devices Describes the free TI codecs that come with production licensing and are available for download now. All are production-tested for easy integration into video, and voice applications. Processor SDK for 66AK2HX Processors - Linux and TI-RTOS Support Describes the unified software platform for TI embedded processors providing easy setup and fast out-of-the-box access to benchmarks and demos. SYS/BIOS and Linux Multicore Software Development Kits (MCSDK) for C66x, C647x, C645x Processors Provides highly-optimized bundles of foundational, platform-specific drivers to enable development on selected TI ARM and DSP devices. The MCSDK gives developers the ability to evaluate hardware and software capabilities of the evaluation platform and to rapidly develop applications. DSP Math Library for Floating-Point Devices Describes the optimized floating-point math function library for C programmers using TI floating point devices. TMS320C6000 DSP Library (DSPLIB) Describes the platform optimized DSP function library for C programmers. It includes C-callable, general-purpose signal-processing routines that are typically used in computationally intensive real-time applications. TMS320C6000 Image Library (IMGLIB) Provides an optimized image/video processing function library for C programmers. It includes C-callable general-purpose image/video processing routines that are typically used in computationally intensive real-time applications. Development Tools Code Composer Studio (CCS) Integrated Development Environment (IDE) for Multicore Processors Integrated development environment (IDE) that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and 314 Device and Documentation Support Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 debug embedded applications. It includes an optimizing C/C++ compiler, source code editor, project build environment, debugger, profiler, and many other features. The intuitive IDE provides a single user interface taking you through each step of the application development flow. Familiar tools and interfaces allow users to get started faster than ever before. Code Composer Studio combines the advantages of the Eclipse software framework with advanced embedded debug capabilities from TI resulting in a compelling feature-rich development environment for embedded developers. XDS200 USB Debug Probe Features a balance of low cost with good performance between the super low cost XDS100 and the high performance XDS560v2. Also, all XDS debug probes support Core and System Trace in all ARM and DSP processors that feature an Embedded Trace Buffer (ETB). XDS560v2 System Trace USB & Ethernet Debug Probe Adds system pin trace in its large external memory buffer. Available for selected TI devices, this external memory buffer captures device-level information that allows obtaining accurate bus performance activity and throughput, as well as power management of core and peripherals. Also, all XDS debug probes support Core and System Trace in all ARM and DSP processors that feature an Embedded Trace Buffer (ETB). XDS560v2 System Trace USB Debug Probe Connects to the target board via a MIPI HSPT 60-pin connector (with multiple adapters for TI 14-pin, TI 20-pin and ARM 20 pin) and to the host PC via USB2.0 High speed (480Mbps). It also requires a license of Code Composer Studio IDE running on the host PC. TI Design Network Keystone II SoC Solution Provides a complete stack of operating system and communications software for the TI Keystone II architecture. It includes a Yocto based commercial Linux distribution, DSP operating system (OSEck®) and an optimized communication service between ARM cores, DSP cores, and external CPUs in the system (LINX). OSEck Provides a full-featured, compact, real-time kernel for DSPs that is optimized to suit the specific requirements of high performance, memory constrained applications. OSEck is a compact kernel and has an extremely small memory footprint, but still combines rich functionality with high performance and true real-time behavior. Wind River Linux Delivers a commercial-grade Linux platform, advanced features, fully integrated development tools and worldwide support. Wind River Vxworks Delivers a proven combination of high-performance determinism with a flexible modular architecture to optimize footprint and deliver unparalleled scalability, advanced security, and comprehensive multicore options. 12.3 Documentation Support To receive notification of documentation updates, navigate to the device product folder on ti.com (66AK2H14, 66AK2H12, 66AK2H06). In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. The current documentation that describes the DSP, related peripherals, and other technical collateral is listed below. Errata 66AK2H06/12/14 Multicore DSP+ARM KeyStone II SOC Silicon Errata Describes the silicon updates to the functional specifications for the 66AK2H06/12/14 fixedand floating-point digital signal processor. Application Reports SERDES Link Commissioning on KeyStone I and II Devices Explains the SerDes transmit and receive parameters tuning, tools and some debug techniques for TI Keystone I and Keystone II devices. TI DSP Benchmarking Provides benchmarks for the C674x DSP core, the C66x DSP core and the ARM Cortex-A15 core. Device and Documentation Support Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 315 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com Throughput Performance Guide for KeyStone II Devices Analyzes various performance measurements of the KeyStone II family of processors. It provides a throughput analysis of the various support peripherals to different end-points and memory access. Keystone II DDR3 Debug Guide Provides tools for use when debugging a failing DDR3 interface on a KeyStone II device. Keystone II DDR3 Initialization Provides a step-to-step initialization guide for the Keystone II device DDR3 SDRAM controller. DDR3 Design Requirements for KeyStone Devices Provides implementation instructions for the DDR3 interface incorporated in the TI KeyStone series of DSP devices. The DDR3 interface supports 1600 MT/s and lower memory speeds in a variety of topologies. Hardware Design Guide for KeyStone II Devices Describes hardware system design considerations for the KeyStone II family of processors. This design guide is intended to be used as an aid during the development of application hardware. Other aids including, but not limited to, device data manuals and explicit collateral should also be used. Multicore Programming Guide Presents a programming methodology for converting applications to run on multicore devices. PCIe Use Cases for KeyStone Devices Gives examples of PCIe usage in KeyStone devices including address translation, multidevice connection, and programming examples. The C6000 EABI Migration Guide Describes the C6000 compiler tools embedded application binary interface (EABI). Clocking Design Guide for KeyStone Devices Covers the general concept of AC and DC clock coupling, terminations, and the impact of incorrect connections on the DSP and selected clock source. Thermal Design Guide for KeyStone Devices Provides specific information and regarding thermal design requirements for all Keystone DSP processors. considerations Optimizing Loops on the C66x DSP Presents strategies and examples for improving performance of C/C++ applications. User's Guides ARM Optimizing C/C++ Compiler Explains how to use these compiler tools: compiler, library build utility, and C++ name demangler. ARM Assembly Language Tools Explains how to use these object file tools: Assembler, archiver, linker, library information archiver, absolute lister, cross-reference lister, disassembler, object file display utility, name utility, strip utility, and hex conversion utility. KeyStone Architecture Phase Locked Loop (PLL) Controller User's Guide Describes the operation of the KeyStone software-programmable phase-locked loop (PLL) Controller. The PLL Controller offers flexibility and convenience by way of softwareconfigurable multipliers and dividers to modify the input signal internally. The resulting clock outputs are passed to the CorePacs, peripherals, and other modules inside the device. KeyStone II Architecture Serializer/Deserializer (SerDes) User's Guide The SerDes performs serial-to-parallel conversions on data received from a peripheral device and parallel-to-serial conversion on data received from the CPU. The SerDes includes control capability and a processor interrupt system that can be tailored to minimize software management of the communications link. KeyStone Architecture Enhanced Direct Memory Access 3 (EDMA3) User's Guide Describes the Enhanced Direct Memory Access (EDMA3) controller. The primary purpose of the EDMA3 controller is to service data transfers that you program between two memorymapped slave endpoints on the device. KeyStone Architecture Multicore Navigator User's Guide Describes the functionality, operational details, and programming information for the 316 Device and Documentation Support Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 PKTDMA and the components of the QMSS in KeyStone architecture devices. Keystone II Architecture DDR3 Memory Controller User's Guide Describes how the DDR3 memory controller is used to interface with JESD79-3C standard compliant SDRAM devices. Memory types such as DDR1 SDRAM, DDR2 SDRAM, SDR SDRAM, SBSRAM, and asynchronous memories are not supported. The DDR3 memory controller SDRAM can be used for program and data storage. KeyStone Architecture Power Sleep Controller (PSC) User's Guide Describes the functionality, operational details, and programming information for the Power Sleep Controller (PSC) module in KeyStone architecture devices. KeyStone II Architecture Universal Serial Bus 3.0 (USB 3.0) User's Guide Describes the features, architecture, and details of the Universal Serial Bus 3.0 (USB 3.0) peripheral. KeyStone Architecture Peripheral Component Interconnect Express (PCIe) User's Guide Describes the features, architecture, and details of the Peripheral Component Interconnect Express (PCIe). KeyStone II Architecture Debug and Trace User's Guide Describes the capabilities of the trace features available through the debug architecture on KeyStone devices. Trace information can be gathered at the DSP core level or at the system level. The Debug Subsystem captures and exports trace data for both levels of trace. Trace is implemented as a nonintrusive debug tool within the KeyStone architecture, but can be selected to operate in both intrusive and nonintrusive mode depending on the amount of data the user wants to export. KeyStone II Architecture ARM Bootloader User's Guide Describes the features of the on-chip bootloader provided with the ARM Cortex-A15 processor. KeyStone Architecture DSP Bootloader User's Guide Describes the features of the on-chip bootloader provided with C66x_Digital Signal Processors (DSP). KeyStone Architecture Gigabit Ethernet (GbE) Switch Subsystem User's Guide Gives a functional description of the Ethernet Switch Subsystem and related portions of the Serializer/Deserializer (SerDes) module. The Ethernet Switch Subsystem consists of the Ethernet Media Access Controller (EMAC) module, Serial Gigabit Media Independent Interface (SGMII) modules, Physical Layer (PHY) device Management Data Input/Output (MDIO) module, Ethernet Switch module, and other associated submodules that are integrated on the device. TMS320C66x DSP CorePac User's Guide Provides an overview of the main components and features of the C66x CorePac. KeyStone Architecture Memory Protection Unit (MPU) User's Guide Describes the functionality, operational details, and programming information for the KeyStone Architecture Memory Protection Unit (MPU). KeyStone Architecture HyperLink User's Guide Provides a high-speed, low-latency, and low-pin-count communication interface that extends the internal CBA 3.x-based transactions between two KeyStone devices. KeyStone II Architecture 10 Gigabit Ethernet Subsystem User's Guide Gives a functional description of the 10 Gigabit Ethernet Switch Subsystem and related portions of the Serializer/Deserializer (SerDes) module. The Ethernet Switch Subsystem consists of the Ethernet Media Access Controller (EMAC) module, Serial Gigabit Media Independent Interface (SGMII) modules, Physical Layer (PHY) device Management Data Input/Output (MDIO) module, Ethernet Switch module, and other associated submodules that are integrated on the device. KeyStone Architecture Security Accelerator (SA) User's Guide Provides hardware engines to perform encryption, decryption, and authentication operations on packets for commonly supported protocols, including IPsec ESP and AH, SRTP, and Air Cipher. The SA also provides the hardware modules to assist the host in generating public keys and random numbers. KeyStone II Architecture Multicore Shared Memory Controller (MSMC) User's Guide The MSMC manages traffic among ARM CorePacs, multiple C66x CorePacs, DMA, other Device and Documentation Support Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 317 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com mastering peripherals, and the EMIF in a multicore device. MSMC also provides a shared on-chip SRAM that is accessible by all the CorePacs and the mastering peripherals on the device. MSMC provides memory protection for accesses to the MSMC SRAM and DDR3 memory from system masters. KeyStone Architecture Serial Rapid IO (SRIO) User's Guide Describes the general operation of SRIO, how this module is connected to the outside world, the features supported, SRIO registers, and examples of channel and queue operations. KeyStone II Architecture ARM CorePac User's Guide Describes the ARM CorePac in the KeyStone II Architecture, but it does not describe the details of the ARM core itself. KeyStone Architecture Packet Accelerator (PA) User's Guide One of the main components of the network coprocessor (NETCP) peripheral, the PA works together with the security accelerator (SA) and the gigabit Ethernet switch subsystem to form a network processing solution. The purpose of PA in the NETCP is to perform packet processing operations such as packet header classification, checksum generation, and multiqueue routing. KeyStone Architecture Serial Peripheral Interface (SPI) User's Guide Describes the features, architecture and registers associated with the serial peripheral interface (SPI) module. KeyStone Architecture Chip Interrupt Controller (CIC) User's Guide Describes the functionality, operational details, and programming information for the KeyStone Architecture Chip Interrupt Controller (CIC). KeyStone Architecture Timer 64P User's Guide Provides an overview of the 64-bit timer in the KeyStone Architecture devices. The timer can be configured as a general-purpose 64-bit timer, dual general-purpose 32-bit timers, or a watchdog timer. When configured as dual 32-bit timers, each half can operate in conjunction (chain mode) or independently (unchained mode) of each other. KeyStone Architecture Inter-IC control Bus (I2C) User's Guide Describes the inter-integrated circuit (I2C) module in the KeyStone Architecture Digital Signal Processor (DSP). The I2C provides an interface between the KeyStone device and other devices compliant with Philips Semiconductors Inter-IC bus (I2C-bus) specification version 2.1 and connected by way of an I2C-bus. This document assumes the reader is familiar with the I2C-bus specification. KeyStone Architecture External Memory Interface (EMIF16) User's Guide Describes the operation of the External Memory Interface (EMIF16) module in the KeyStone DSP family (refer to the device data manual for applicability to a particular part). The EMIF16 module is accessible across all the cores and all system masters that are not cores. TMS320C66x DSP Cache User's Guide Describes how the cache-based memory system of the C66x DSP can be efficiently used in DSP applications. The internal memory architecture of these devices is organized in a twolevel hierarchy consisting of a dedicated program memory (L1P) and a dedicated data memory (L1D) on the first level. Accesses by the core to the these first level memories can complete without core pipeline stalls. KeyStone Architecture General-Purpose Input/Output (GPIO) User's Guide Describes the general-purpose input/output (GPIO) peripheral in the KeyStone digital signal processors (DSPs). KeyStone Architecture Universal Asynchronous Receiver/Transmitter (UART) User's Guide Performs serial-to-parallel conversions on data received from a peripheral device and parallel-to-serial conversion on data received from the CPU. The UART includes control capability and a processor interrupt system that can be tailored to minimize software management of the communications link. TMS320C66x DSP CPU and Instruction Set Reference Guide Describes the CPU architecture, pipeline, instruction set, and interrupts of the C66x DSP. KeyStone Architecture Network Coprocessor (NETCP) User's Guide Describes the network coprocessor (NETCP) hardware accelerator that processes data packets with a main focus on processing Ethernet packets. NETCP has two gigabit Ethernet (GbE) modules to send and receive packets from an IEEE 802.3 compliant network, a packet accelerator (PA) to perform packet classification operations such as header matching, 318 Device and Documentation Support Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 and packet modification operations such as checksum generation, A and a security accelerator (SA) to encrypt and decrypt data packets. Device and Documentation Support Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 319 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com White Papers Multicore SoCs Stay a Step Ahead of SoC FPGAs Describes the differences between SoCs and FPGAs. Recently, the integration of ARM Cortex-A cores into FPGAs and compute-intense cores could lead one to believe that the paths of true multicore SoCs and these so-called FPGA SoCs had converged. A closer examination reveals that in reality they are still very far apart and that true multicore SoCs offer increasing advantages in those critical areas required by today’s demanding products. Save Power and Costs With TI's K2E On-Chip Networking Features Outlines the network subsystem and its associated accelerators on the latest members of the KeyStone II family, AM5K2Ex and 66AK2Ex devices, referred to collectively as K2E. Keeping the “Green” in Network Function Virtualization Provides analysis that will make it possible to reduce central office power consumption while also meeting the demands of the NFV architecture through deployment of the HP Proliant m800 cartridge. KeyStone II-Based Processors: 10G Ethernet as an Optical Interface Deals with how the 10GbE interface and the processing power of the processors based on KeyStone II architecture helps to address complex time-critical systems, like radar systems. Differentiating AM5K2E02 and AM5K2E04 SoCs from Alternate ARM Cortex-A15 Devices Discusses some of the differentiating features of TI’s AM5K2E02 and AM5K2E04 processors based on ARM Cortex-A15 MPCores and TI’s KeyStone architecture. Getting Started on TI ARM Embedded Processor Development Explores the fundamentals of embedded design that influence a system’s architecture and, consequently, impact processor selection. Accelerate Multicore Application Development With KeyStone Software Explores how Texas Instruments KeyStone multicore SoCs offload many software functions into hardware AccelerationPacs or other architectural elements to reduce the amount of software needed and to automate many of the more complex multicore management tasks. White Space – Potentials and Realities Highlights the exciting new potential of white space, yet tempered with a few technical realities. Enhancing the KeyStone II Multicore Architecture With ARM Summarizes how multicore Cortex-A15 processors in the KeyStone II architecture enable optimum performance for embedded infrastructure applications. A Better Way to Cloud Explores the factors around the shifts in cloud computing and highlights the differences between traditional cloud computing and cloud computing-based on embedded processing. Design Files 66AK2H14 66AK2H12 66AK2H106 AAW OrCAD Symbols Provides spreadsheets of 66AK2H14, 66AK2H12, and 66AK2H106 AAW OrCAD symbols. Other Documents The Case for 10G Ethernet in Embedded Processing Describes how Ethernet has kept its focus and added an order of magnitude bandwidth. 66AK2Hx KeyStone Multicore DSP+ARM System-on-Chips Describes how the 66AK2Hx platform is TI’s first to combine quad ARM Cortex-A15 MPCore processors with up to eight TMS320C66x high-performance DSPs using the KeyStone II multicore architecture. 320 Device and Documentation Support Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 Multicore DSPs for High-Performance Video Coding Describes how the multicore processors offer high-performance processing capabilities with full programmability in a cost- and power-optimized package. Video Infrastructure - Applications of the K2E, K2H Platforms Describes how the devices in the K2H platform are well suited to provide scale and density for video processing. Industrial Imaging: Applications of the K2H and K2E Platforms Describes how the Cortex-A15 processors enable developers to quickly and easily migrate existing software designs to the low-power, high-performance K2E and K2H platforms. 12.4 Related Links Table 12-1 lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 12-1. Related Links PARTS PRODUCT FOLDER ORDER NOW TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY 66AK2H14 Click here Click here Click here Click here Click here 66AK2H12 Click here Click here Click here Click here Click here 66AK2H06 Click here Click here Click here Click here Click here 12.5 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community The TI engineer-to-engineer (E2E) community was created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. TI Embedded Processors Wiki Established to help developers get started with Embedded Processors from Texas Instruments and to foster innovation and growth of general knowledge about the hardware and software surrounding these devices. 12.6 Trademarks KeyStone, SmartReflex, C6000, E2E are trademarks of Texas Instruments. MPCore, NEON, CoreSight, ARM7 are trademarks of ARM Ltd or its subsidiaries. ARM, Cortex, Jazelle, Thumb are registered trademarks of ARM Ltd or its subsidiaries. Windows is a registered trademark of Microsoft Corp. All other trademarks are the property of their respective owners. 12.7 Electrostatic Discharge Caution This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 12.8 Glossary TI Glossary This glossary lists and explains terms, acronyms, and definitions. Device and Documentation Support Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 321 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com 13 Mechanical, Packaging, and Orderable Information 13.1 Packaging Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 322 Mechanical, Packaging, and Orderable Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 PACKAGE OUTLINE AAW1517B FCBGA - 3.62 mm max height SCALE 0.370 PLASTIC BALL GRID ARRAY 40.2 39.8 A B BALL A1 CORNER 40.2 39.8 ( 32) ( 30) 3.62 MAX C SEATING PLANE BALL TYP 0.2 C (1.08) 0.6 TYP 0.4 38 TYP SYMM (1) TYP AW AV AT AP AM AK AH AF AD 38 TYP AB Y V T P M AU AN AL AJ AG AE AC W U R B 1517X N 0.7 0.5 L K D SYMM AA 0.25 0.1 J H F (1) TYP AR G C A C B E C A 1 1 TYP BALL A1 CORNER 3 2 5 4 7 6 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 1 TYP 4222495/A 01/2016 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. www.ti.com Figure 13-1. Package Outline Mechanical, Packaging, and Orderable Information Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 323 66AK2H14, 66AK2H12, 66AK2H06 SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 www.ti.com EXAMPLE BOARD LAYOUT AAW1517B FCBGA - 3.62 mm max height PLASTIC BALL GRID ARRAY 1517X ( (1) TYP SYMM 0.45) A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 (1) TYP B C D E F G H J K L M N P R T U V W Y AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AR AT AU AV AW SYMM LAND PATTERN EXAMPLE SCALE:3X 0.05 MAX ( 0.45) METAL 0.05 MIN METAL UNDER SOLDER MASK SOLDER MASK OPENING NON-SOLDER MASK DEFINED (PREFERRED) ( 0.45) SOLDER MASK OPENING SOLDER MASK DEFINED SOLDER MASK DETAILS NOT TO SCALE 4222495/A 01/2016 NOTES: (continued) 3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints. For information, see Texas Instruments literature number SPRU811 (www.ti.com/lit/spru811). www.ti.com Figure 13-2. Example Board Layout 324 Mechanical, Packaging, and Orderable Information Copyright © 2012–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 66AK2H14, 66AK2H12, 66AK2H06 www.ti.com SPRS866G – NOVEMBER 2012 – REVISED OCTOBER 2017 EXAMPLE STENCIL DESIGN AAW1517B FCBGA - 3.62 mm max height PLASTIC BALL GRID ARRAY 1517X ( 0.45) (1) TYP SYMM A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 B (1) TYP C D E F G H J K L M N P R T U V W Y AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AR AT AU AV AW SYMM SOLDER PASTE EXAMPLE BASED ON 0.15 mm THICK STENCIL SCALE:3X 4222495/A 01/2016 NOTES: (continued) 4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. www.ti.com Figure 13-3. Example Stencil Design Mechanical, Packaging, and Orderable Information Submit Documentation Feedback Product Folder Links: 66AK2H14 66AK2H12 66AK2H06 Copyright © 2012–2017, Texas Instruments Incorporated 325 PACKAGE OPTION ADDENDUM www.ti.com 3-Jan-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking (4/5) (6) 66AK2H06DAAW2 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR 0 to 85 66AK2H06AAW @2012 TI 66AK2H06DAAW24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR 0 to 85 66AK2H06AAW @2012 TI 1.2GHZ/1.4GHZ 66AK2H06DAAWA2 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H06AAW @2012 TI A1.2GHZ 66AK2H06DAAWA24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H06AAW @2012 TI A1.2GHZ/1.4GHZ 66AK2H12DAAW2 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR 0 to 85 66AK2H12AAW @2012 TI 66AK2H12DAAW24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR 0 to 85 66AK2H12AAW @2012 TI 1.2GHZ/1.4GHZ 66AK2H12DAAWA2 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H12AAW @2012 TI A1.2GHZ 66AK2H12DAAWA24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H12AAW @2012 TI A1.2GHZ/1.4GHZ 66AK2H12DXAAWA24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H12XAAW @2012 TI A1.2GHZ/1.4GHZ 66AK2H14DAAW24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR 0 to 85 66AK2H14DAAWA24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H14AAW @2012 TI A1.2GHZ/1.4GHZ 66AK2H14DXAAWA24 ACTIVE FCBGA AAW 1517 21 RoHS & Green Call TI Level-4-245C-72HR -40 to 100 66AK2H14XAAW @2012 TI A1.2GHZ/1.4GHZ Addendum-Page 1 66AK2H14AAW @2012 TI 1.2GHZ/1.4GHZ Samples PACKAGE OPTION ADDENDUM www.ti.com 3-Jan-2022 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of