User's Guide
SLOU257B – October 2009 – Revised March 2015
AFE5801 8-Channel Variable Gain Amplifier (VGA) with
Octal High-Speed ADC
The AFE5801EVM is an evaluation tool designed for the ultrasound analog front-end (AFE) device
AFE5801. In order to deserialize the outputs of AFE5801, an ADSDeSer-50EVM or TSW1400EVM is
needed during the evaluation.
Contents
Introduction ................................................................................................................... 3
1.1
AFE5801EVM Kit Contents ........................................................................................ 3
1.2
Features .............................................................................................................. 3
1.3
Power Supplies ..................................................................................................... 3
1.4
Indicators............................................................................................................. 3
2
Board Configuration ......................................................................................................... 5
2.1
Board Connections Overview ..................................................................................... 5
2.2
I/O and Power Connectors ........................................................................................ 6
2.3
Jumpers and Setup ................................................................................................. 6
2.4
Test Points ........................................................................................................... 9
3
Board Operation ............................................................................................................. 9
3.1
Software Installation and Operation .............................................................................. 9
3.2
Hardware Setup ................................................................................................... 14
3.3
Clock Selection .................................................................................................... 14
3.4
Data Analysis ...................................................................................................... 15
4
Schematics, Layout, and, Bill of Materials .............................................................................. 16
4.1
Schematics ......................................................................................................... 16
4.2
PCB Layout ........................................................................................................ 22
4.3
Bill of Materials .................................................................................................... 30
5
Typical Performance ....................................................................................................... 32
Appendix A
TSW1400 for Evaluating AFE5801 ............................................................................. 33
Appendix B
High Speed Data Converter Pro (HSDCPro) GUI Installation .............................................. 45
1
List of Figures
1
AFE5801EVM LED Locations .............................................................................................. 4
2
AFE5801EVM TOP View ................................................................................................... 5
3
AFE5801EVM BOTTOM View ............................................................................................. 5
4
Locations of Jumpers, Headers and Switches on the AFE5801EVM................................................. 7
5
Default Setup for Jumpers .................................................................................................. 8
6
Found New Hardware Wizard Screen
7
Found New Hardware Wizard (Next) Screen ........................................................................... 10
....................................................................................
9
8
................................................................................................................................
9
AFE5801EVM USB SPI Interface for General Registers.............................................................. 11
10
AFE5801EVM USB SPI Fixed Gain Mode .............................................................................. 12
11
AFE5801EVM USB SPI Interface for Variable Gain Mode ........................................................... 13
12
Typical AFE5801 Bench Setup:
13
Clock Selection Jumper Configurations: (a) Transformer (default); (b) Single-ended Clock; (c) Future
.........................................................................................
10
14
Microsoft, Windows are registered trademarks of Microsoft Corporation.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
1
www.ti.com
CLK Input Option Based on U1. Both (b) and (c) Configurations Need Some Modifications on the PCB. ..... 14
14
Schematic Page 1 .......................................................................................................... 16
15
Schematic Page 2 .......................................................................................................... 17
16
Schematic Page 3 .......................................................................................................... 18
17
Schematic Page 4 .......................................................................................................... 19
18
Schematic Page 5 .......................................................................................................... 20
19
Schematic Page 6 .......................................................................................................... 21
20
Top Layer Signal ........................................................................................................... 22
21
Inner Layer 1 Ground ...................................................................................................... 23
22
Inner Layer 2 Signal
23
Inner Layer 3 Power ....................................................................................................... 25
24
Inner Layer 4 Ground ...................................................................................................... 26
25
Bottom Layer Signal
26
Top Silk Screen Layer ..................................................................................................... 28
27
Bottom Silk Screen Layer ................................................................................................. 29
28
Typical Performance of AFE5801. (a) Fixed Gain Mode; (b) Variable Gain Mode ................................ 32
29
Connection Between TSW1400EVM and AFE5801 ................................................................... 33
30
Connection of the Instruments ............................................................................................ 34
31
AFE5801EVM GUI - RUN Mode ......................................................................................... 35
32
AFE5801 EVM GUI - START Button .................................................................................... 36
33
AFE5801EVM GUI - Variable Gain ...................................................................................... 37
34
AFE5801EVM GUI - Setting Fixed Gain ................................................................................ 38
35
User Interface: Initial Setup Screen ...................................................................................... 39
36
User Interface: Step-by-Step Setup ...................................................................................... 40
37
User Interface: Frequency Load Value to Signal Generator .......................................................... 41
38
User Interface: Final Setup Screen ...................................................................................... 42
39
User Interface: Single FFT Format ....................................................................................... 43
40
User Interface: Time Domain Format .................................................................................... 44
41
Plot of Saved Sample Data ............................................................................................... 44
42
HSDCPro Install (Begin)................................................................................................... 45
43
HSDCPro Install (Install Directory) ....................................................................................... 46
44
HSDCPro Install (TI License Agreement) ............................................................................... 47
45
HSDCPro Install (NI License Agreement) ............................................................................... 48
46
HSDCPro Install (Start Installation) ...................................................................................... 49
47
HSDCPro Install (Installation Progress) ................................................................................. 50
48
HSDCPro Install (Installation Complete) ................................................................................ 51
49
HSDCPro Install (h) ........................................................................................................ 52
50
HSDCPro Install ............................................................................................................ 52
.......................................................................................................
.......................................................................................................
24
27
List of Tables
1
2
Channel-to-Channel Matching Between the AFE5801EVM and ADSDeSER-50EVM ............................ 14
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Introduction
www.ti.com
1
Introduction
AFE5801 includes an 8-channel voltage-Controlled-Amplifier (VCA) with digital control and an 8-channel
65MSPS analog-to-digital converter (ADC). The outputs of the ADC are 8-channel LVDS outputs which
should be deserialized by the ADSDeSer-50EVM or TSW1400EVM. The AFE5801EVM provides an easy
way to examine the performances and functionalities of AFE5801.
1.1
AFE5801EVM Kit Contents
The AFE5801EVM kit contains the following:
• AFE5801 EVM board
• USB cable
1.2
Features
•
•
•
•
•
1.3
Characterize AFE5801
Provide 8-channel LVDS outputs from the ADC
Compatible to the standard TI LVDS deserializer ADSDeSer-50EVM or TSW1400EVM
Communicate with PC through USB interface
Power Management provides multiple power supplies for AFE5801 and other devices.
Power Supplies
The AFE5801EVM requires only +5V power supplies for operation.
1.4
Indicators
The AFE5801EVM has 4 LEDs on the board as shown in Figure 1. Their states demonstrate the normal
operation of AFE5801EVM.
• LED 1: U1 status indicator. Its ON state indicates the clock management chip U1 works well if U1 is
installed.
• LED 3 and 2 (RED): 1.8VD and 1.8VA power supply indicators. ON state indicates that the AFE5801
is powered correctly.
• LED 4 (GREEN): +3.3V power supply indicator. ON state indicates that the AFE5801 is powered
correctly.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
3
Introduction
www.ti.com
LED3 LED4
LED 2
LED 1
Figure 1. AFE5801EVM LED Locations
4
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Configuration
www.ti.com
2
Board Configuration
This chapter describes the locations and functionalities of inputs, outputs, jumpers, test points of the
AFE5801EVM in detail.
2.1
Board Connections Overview
Input
Signals
+5V
PWR
Low Jitter
Clk In
DUT
USB
Ext Clk In
Figure 2. AFE5801EVM TOP View
AFE/TSW
Adapter
Connector
Figure 3. AFE5801EVM BOTTOM View
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
5
Board Configuration
2.2
www.ti.com
I/O and Power Connectors
The positions and functions of the AFE5801EVM connectors are discussed in this section.
• Analog Inputs Ch1~Ch8 (J1~J8): Single-end analog signal is converted to differential signals by
transformer.
• Low Jitter CLK Source Input (J11): This input accepts clocks with low jitter noise, such as HP8644
output. 20~50MHz 50% duty cycle clock with 1~2Vrms amplitude can be used. When J11 is used,
make sure shunts P4, P5, P6 are removed.
• CLK output (J10): The output of either the U1 output or the on-board 40MHz oscillator output
depending on jumper P4’s connection.
• External CLK Input (J9): ADC Clock input, such as FPGA outputs. FPGA outputs must be processed
by U1. Otherwise, the ADC of AFE5801 will not achieve satisfactory performance.
• +5V PWR connector(P10): Power supply input
• USB input (P11): USB interface to control the AFE5801.
• LVDS Outputs Ch1~Ch8 (P13): Differential LVDS data outputs.
2.3
Jumpers and Setup
The board has been set to default mode. Detailed description can be found in Figure 4 and Figure 5.
6
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Configuration
www.ti.com
P15
P14
P8
P2
P3
P12
P4
SW1
P1
P9
P7
P5
P6
Figure 4. Locations of Jumpers, Headers and Switches on the AFE5801EVM
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
7
Board Configuration
www.ti.com
Figure 5. Default Setup for Jumpers
•
•
•
•
•
•
•
•
8
P1: SPI interface for U1
P2, P3: AFE5801 ADC clock input selection: transformer-based differential clock, single-ended
LVCMOS clock, or future clock option (needs U1 to support). Default is to use transformer-based
differential clock.
P4: Select jitter-cleaned clock or non-jitter-cleaned clock. Default is to use non-jitter-cleaned clock (i.e.,
on-board 40MHz clock).
P5: Use on-board 40MHz clock. Default is that the on-board clock is used.
P6: Power on on-board 40MHz clock generator. Default is on.
P8: Debug port for monitoring ADS SPI signals.
P9: USB interface enable. Default is on.
Regulated power supply outputs (P12, P7): 1.8VA, 1.8VD, and 3.3V. P12 and P7 can be configured as
power supply input as well if users would like to skip the on-board regulators. Remove the ferrite beads
L1, L2, L3, L7 and L24,
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Configuration
www.ti.com
•
2.4
Test Points
•
3
SW1: Reset switch for AFE5801.
Multiple Test Points are provided on the EVM. Refer to the attached schematics for more information.
Board Operation
This chapter describes how to operate the AFE5801EVM for evaluation. Both software and hardware
installation and operation are discussed.
3.1
Software Installation and Operation
The AFE5801EVM comes with a software install. To Dowload the software, visit the AFE5801 product
folder in the Tools & software section. Once the zip folder is downloaded, run setup.exe to install the
software. The software to use the TSW1400EVM is called HSDCPro (High Speed Data Converter Pro).
For information on how to download this software, please see Appendix B.
USB Driver Installation
• Connect the USB port of EVM to your PC.
• If the driver has not been installed then the message “Windows Found New Hardware” will appear.
The Wizard as the following picture will launch.
• Select "No, not this time" from the options. Press Next button
Figure 6. Found New Hardware Wizard Screen
•
Select "Install from a list or specific location (Advanced)" as shown below and then click "Next".
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
9
Board Operation
www.ti.com
Figure 7. Found New Hardware Wizard (Next) Screen
•
•
Select "Search for the best driver in these locations" and enter the file path for ("C:\Program
Files\AFE5801\CDM 2.04.06 WHQL Certified ") in the combo-box or browse to it by clicking the browse
button. Once the file path has been entered in the box, click next to proceed.
If Microsoft® Windows® XP is configured to warn when unsigned (non-WHQL certified) drivers are
about to be installed, the following screen will be displayed unless installing a Microsoft WHQL certified
Driver. Click on "Continue Anyway" to continue with the installation. If Windows XP is configured to
ignore file signature warnings, no message will appear.
Figure 8.
10
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Operation
www.ti.com
GUI Startup
• Launch GUI from XP Window
• Start → All Programs\AFE5801EVM\AFE5801
• Several different screens appear displaying the different modes (Figure 9 through Figure 11)
Figure 9. AFE5801EVM USB SPI Interface for General Registers.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
11
Board Operation
www.ti.com
Figure 10. AFE5801EVM USB SPI Fixed Gain Mode
12
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Operation
www.ti.com
Figure 11. AFE5801EVM USB SPI Interface for Variable Gain Mode
When AFE5801EVM is powered on, all registers have been set to their default modes. Refer to the
datasheet for all default settings. It is recommended to restart the SPI software when AFE5801 is powered
on in order to synchronize the AFE5801 register settings to the software displays.
Users also can fill out Address Bytes and Data Bytes and press ENTER to configure each register.
Typical Configuration
• From Figure 9 press "Init for TSW1400" button
• Select TAB “TGC Register” - Figure 10 will appear
• From Figure 11, press “Variable” button to get into fixed gain mode
• From Figure 10 enter 30 in the “Coarse Gain(dB)” field then press “Write” button.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
13
Board Operation
3.2
www.ti.com
Hardware Setup
As mentioned before, Xilinx DeSerializer ADSDeSER-50EVM or TSW1400EVM is required. Please see
details in the corresponding application notes on how to use the either of these EVMs. An example bench
setup is shown in Figure 12. Band-pass filters are required for signal source in order to ensure the correct
SNR measurements of the AFE5801.
Figure 12. Typical AFE5801 Bench Setup:
The channel order of the AFE5801 outputs is not exactly the same as the one of ADS527x outputs. As a
result, the channel number on the ADSDeSER-50EVM or AFE5801EVM might be misleading. Table 1
provides channel-to-channel sequence matching between the ADSDeSER-50EVM and AFE5801EVM.
Table 1. Channel-to-Channel Matching Between the AFE5801EVM and ADSDeSER-50EVM
AFE
FCLK
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
LCLK
Xilinx
FCLK
CH8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
LCLK
For example, when an analog signal is input at CH1 on the AFE5801EVM, the corresponding 12-bit digital
output will be seen at CH8 on the ADSDeSER-50EVM when the AFE5801 is configured as 8-channel
mode.
3.3
Clock Selection
AFE5801 is typically clocked through a transformer-based circuit. Other options are also available if
needed as shown in Figure 13.
(a)
(b)
(c)
Figure 13. Clock Selection Jumper Configurations: (a) Transformer (default);
(b) Single-ended Clock; (c) Future CLK Input Option Based on U1.
Both (b) and (c) Configurations Need Some Modifications on the PCB.
14
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Board Operation
www.ti.com
The clock source of the EVM could be the on-board clock 40MHz, HP8644 low jitter clock source, or
external clock source. The best performance of this EVM is achieved when low-jitter clock source HP8644
is used. The P4, P5, P6 should be removed in order to disable the on-board clock.
When HP8644 or similar clock sources are not available, the on-board 40MHz clock is also a desirable
source. The jumpers P4, 5, 6 should be configured as Figure 13 shows (i.e., default setup for
AFE5801EVM). In this mode, the transform-based differential clock is used.
3.4
Data Analysis
Based on the data file acquired by a logic analyzer, the performance of AFE5801 can be evaluated.
In Appendix A, we provide one solution (TI TSW1400 EVM) to analyze the data file using the PC.
Appendix B provides step by step instructions on how to download the HSDCPro (Hish Speed Data
Converter Pro) GUI, which accompanies the TSW1400EVM. Coherent sampling is recommended if the
input and sampling clock are phase locked. Due to the frequency accuracy requirement of coherence
sampling, two HP8644s for generating ADC clock and analog signal are required. For most users, this
may not be feasible. Data analysis based on windowing is a more suitable approach.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
15
Schematics, Layout, and, Bill of Materials
4
www.ti.com
Schematics, Layout, and, Bill of Materials
This chapter provides the schematics and layout of the AFE5801EVM as well as the bill of materials.
4.1
Schematics
Figure 14. Schematic Page 1
16
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 15. Schematic Page 2
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
17
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 16. Schematic Page 3
18
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 17. Schematic Page 4
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
19
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 18. Schematic Page 5
20
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
(1)
www.ti.com
(1) Pin 28 may also be connected
to 1.8 V per the AFE5801 data sheet,
(SLOS591).
Figure 19. Schematic Page 6
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
21
Schematics, Layout, and, Bill of Materials
4.2
www.ti.com
PCB Layout
A
•
•
•
•
•
•
•
•
six-layer printed-circuit board is used:
Top Layer, signal
Inner Layer 1, ground
Inner Layer 2, signal
Inner Layer 3, power
Inner Layer 4, ground
Bottom Layer, signal
Top Silk Screen Layer
Bottom Silk Screen Layer
Figure 20. Top Layer Signal
22
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 21. Inner Layer 1 Ground
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
23
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 22. Inner Layer 2 Signal
24
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 23. Inner Layer 3 Power
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
25
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 24. Inner Layer 4 Ground
26
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 25. Bottom Layer Signal
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
27
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 26. Top Silk Screen Layer
28
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
Figure 27. Bottom Silk Screen Layer
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
29
Schematics, Layout, and, Bill of Materials
4.3
ITEM
Bill of Materials
MFG
1
30
www.ti.com
MFG PART#
REF DES
VALUE or FUNCTION
UNINSTALLED
C98–C105
Capacitor, SMT, 0402 Uninstalled
2
Kemet
C0402C104K8PAC
C1–C5, C8, C9, C12,
C13, C16, C17, C19,
C20, C24–C28,
C31–C44, C46,
C48–C53, C56–C95,
C107–C114
Capacitor, SMT, 0402, Ceramic, 0.1μF, 10V, 10%, X5R
3
Murata
GRM155R60J225ME15D
C23
Capacitor, SMT, 0402, Ceramic, 2.2 μF, 6.3V, 20%, X5R
4
Panasonic
ECJ-1VB0J475K
C29
Capacitor, SMT, 0603, Ceramic, 4.7 μF, 6.3V, 10%, X5R
5
Panasonic
ECJ-1VB1A105K
C54, C55, C96, C106
Capacitor, SMT, 0603, Ceramic, 1.0 μF, 10V, 10%, X5R
6
Taiyo Yuden
JMK107BJ106MA-T
C21, C22
Capacitor, SMT, 0603, Ceramic, 10 μF, 6.3V, 20%, X5R
7
Murata
GRM31CR60J476ME19B
C30
Capacitor, SMT, Ceramic, 1206, 47 μF, 6.3V, 20%, X5R
8
Vishay
Sprage
293D106X5035D2T
C97, C115
Capacitor, TAN, SMT, 10uF, 35V, ±5%, –55~85C
9
AVX
TPSC226K016R0375
C6, C7, C10, C11, C14,
C15, C18, C45, C47
10%, 16V, 22μF
10
Samtec
SMA-J-P-X-ST-EM1
J1–J9
SMA Jack, Edge mount, 062PCB, Brass/Gold, Straight, 50 Ω
11
Samtec
SMA-J-P-H-ST-TH1
J10–J12
SMA Coax straight PCB Jack, SMT, 175TL, 50 Ω, Gold
12
KYCON
KMBX-SMT-5S-S-3OTR
P11
USB Connectors MINI-USB B-Type SCKT
13
Samtec
QTH-040-01-L-D-DP-A
P13
Connector, SMT, 80P, 0,5mm, FEM, DIFF Pair, Receptacle,
168H
14
Epson
Toyocom
HF-372A
F1
(Customer Supply) Crystal filter miniature radio Equipment/IF
15
TI
CDCE62005
U1
CDCE62005 UNINSTALLED. TI supply
16
Not Installed
PAD0201(UN)
EP2, EP3
( Uninstalled Part ) Empty pad, SMT, 0201
17
Murata
BLM15BD102SN1D
L9–L20
Ferrite bead, SMT, 0402, 1kΩ, 200 mA
18
Murata
BLM18EG601SN1D
L8
Ferrite bead, SMT, 0603,600 Ω at 100 MHz, 25%, 800 mA
19
Steward
HI0805R800R-00
L1–L7, L21, L22,
L24–L26
Ferrite, SMT, 0805, 80 Ω at 100 MHz, 5 A
20
Steward
LI1206H151R-00
L23
Ferrite, SMT, 1206, 150 Ω at 100 MHz, 0.8 A
21
Molex
39357-0002
P10
Header, THRU, Power, 2P, 3.5MM, Eurostyle
22
Samtec
SSQ-104-02-F-D
P1
Header, THU, 8P, 2X4, 100LS, FEM, VERT, 194TL
23
Samtec
TSW-103-08-G-D
P2, P3
Header, THU, 6P, 2X3, male, dual row, 100LS, 200TL
24
Tyco
Electronics
103321-2
P6, P9
Header w/shunt, 2P, 100LS
25
Molex
22-23-2021-P
P7
MALE, 2PIN, 0.100CC w/ friction lock
26
Mill-Max
350-10-103-00-006
P4, P5
Header, THU, MAL, 0.1LS, 3P, 1X3, 284H, 110TL
27
Molex
22-23-2041
P12
4P, VERT, Friction lock
28
Samtec
TSW-108-05-G-S
P8
Header, THU, 8P, 1X8, male, single row, 100LS, 130TL
29
TI
TPS79618DCQR
U5
Ultralow-noise HI PSRR Fast RF 1-A LDO Linear regulator,
1.8V
30
TI
TPS79633DCQR
U4
Ultralow-noise HI PSRR Fast RF 1-A LDO Linear regulator,
3.3V
31
TI
TPS79318DBV
U3 (UNINSTALLED)
1.8V,Ultralow-noise HI PSRR Fast RF 200 mA LDO Linear
regulator
32
Future
Technology
Device Int.
FT245RL
U6
USB FIFO IC Incorporate FTDICHIP-ID Security dongle
33
Any
JUMPER,2P 0.100cc
EP5, EP6
Installed any brand 2PIN THU Jumper
34
Any
JUMPER,3P 0.100cc 123
P14, P15
Installed jumper, THU, 3P 0.100cc, 123
35
Panasonic
LNJ308G8PRA
LED1, LED4
LED, SMT, 0603, pure green, 2.03V
36
Panasonic
LNJ808R8ERA
LED2, LED3
LED, SMT, 0603, orange, 1.8V
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Schematics, Layout, and, Bill of Materials
www.ti.com
ITEM
MFG
MFG PART#
REF DES
VALUE or FUNCTION
37
ECS
ECS-3953M-400-BN
U2
OSC, SMT, 3.3V, 50ppm, -40~85C, 5nS, 40.000 MHz
38
Vishay
CRCW04021002F100
R28, R29, R30
Resistor, SMT, 0402, 10K, 1/16W, 1%, 100ppm
39
Panasonic
ERJ-2GE0R00X
R8, R10–R12, R15,
R19, R20, R32, R44,
R45, R48, R49, R52,
R53, R56, R57, R60,
R61, R64, R65, R68,
R69, R72, R73, R76,
R77, R79, R80
Resistor/jumper,SMT, 0402, 0 Ω, 5%, 1/16W
40
Panasonic
ERJ-2GEJ0000(UN)
R5, R7, R9, R14, R17,
R18
( UNINSTALLED PART )
41
Panasonic
ERJ-2GEJ131
R21, R22
Resistor, SMT, 0402, thick film, 5%, 1/16W, 130
42
Panasonic
ERJ-2GEJ49R9(UN)
R25, R36–R43
( UNINSTALLED PART )
43
Panasonic
ERJ-2GEJ820
R23, R24
Resistor, SMT, 0402, thick film, 5%, 1/16W, 82
44
Panasonic
ERJ-2RKF1000X
R2, R3
Resistor, SMT, 0402, 100 Ω, 1%, 1/16W
45
Panasonic
ERJ-2RKF1001X
R4
46
Panasonic
ERJ-2RKF25R5X
R46,
R54,
R62,
R70,
47
Panasonic
ERJ-2RKF3320X
R1, R6, R16
Resistor, SMT, 0402 332 Ω, 1%, 1/16W
48
Panasonic
ERJ-2RKF49R9X
R26, R27, R33
Resistor, SMT, 0402, 49.9 Ω, 1%, 1/16W
49
Panasonic
ERJ-3GSYJ100
R78
Resistor, SMT, 0603, 5%, 1/10W, 10
50
Vishay
CRCW08051002F
R31, R34, R35
Resistor, SMT, 0805, thick film, 1%, 1/8W, 10.0K
51
Panasonic
ERJ-6RQF5R1V
R13
Resistor, SMT, 0805, 1%, 1/8W, 5.1 Ω
52
Panasonic
ERJ-1GE0R00C
EP1, EP4
Resistor, SMT, 0201, thick film, 0 Ω, 5%,0 Ω Jumper, 1/20W
53
AFE5801
AFE5801
DUT1
AFE5801 Analog Front End. TI supplied.
54
ITT
Industries
PTS635SK25SM
SW1
Switch, SMT, 2P, SPST-NO, 2.5mm Height, MOM,
rectangular, 0.05A, 12V
55
Keystone
Electronics
5005
TP1
Testpoint, THU, compact, 0.125LS, 130TL, red
56
Keystone
Electronics
5006
TP2–TP6
Testpoint, THU, compact, 0.125LS, 130TL, black
57
Mini-Circuits
ADTT1-1
T1–T8
RF Transformer 0.03–300 MHz
58
Mini-Circuits
ADT1-6T
T9
RF Transformer wideband, 0.03–125 MHz
59
PEM
KFS2-M2.5
PEM NUTS
UNINSTALLED
60
AMP
531220-2
P6, P9
SHUNT JUMPER 2POS
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Resistor, SMT, 0402, 1.00K, 1%, 1/16W
R47,
R55,
R63,
R71,
R50,
R58,
R66,
R74,
R51,
R59,
R67,
R75
Resistor, SMT, 0402, 25.5 Ω, 1%, 1/16W
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
Copyright © 2009–2015, Texas Instruments Incorporated
31
Typical Performance
5
www.ti.com
Typical Performance
This chapter provides some typical performance of the AFE5801EVM to assist users to verify their setup.
A typical performance plot of the AFE5801 is shown in Figure 28 with 30dB digital gain setting.
(a)
(b)
Figure 28. Typical Performance of AFE5801. (a) Fixed Gain Mode; (b) Variable Gain Mode
32
AFE5801 8-Channel Variable Gain Amplifier (VGA) with Octal High-Speed
ADC
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Appendix A
SLOU257B – October 2009 – Revised March 2015
TSW1400 for Evaluating AFE5801
A.1
Introduction
This application report goes through the steps of evaluating the AFE501 using the TSW1400EVM.
A.2
Hardware Setup
Figure 29. Connection Between TSW1400EVM and AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
33
Hardware Setup
www.ti.com
Figure 30. Connection of the Instruments
Launch AFE5801 GUI
From PC click Start Menu→All Programs→Texas Instruments→AFE5801EVM USB SPI→AFE5801EVM
USB SPI
The GUI may be running if the following screen appears:
34
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Hardware Setup
www.ti.com
Figure 31. AFE5801EVM GUI - RUN Mode
In case the GUI is not running, then press the START button of the GUI to run it.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
35
Hardware Setup
www.ti.com
Figure 32. AFE5801 EVM GUI - START Button
•
1.
2.
3.
36
Commands to the AFE5801 GUI:
Click Init for TSW1400 to set the proper condition to work with TSW1400EVM.
Go to "TGC Register " Tab.
Press Variable button to change the mode to Fixed.
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Hardware Setup
www.ti.com
Figure 33. AFE5801EVM GUI - Variable Gain
4. Type 30 and press Write button.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
37
Hardware Setup
www.ti.com
Figure 34. AFE5801EVM GUI - Setting Fixed Gain
At this stage the AFE5801 is ready.
Launch TSW1400 GUI
•
Graphics User Interface (GUI)
TSW1400 provides a GUI for users to evaluate the performance of the device. When GUI is started,
the screen of the following figure appears.
For details, see the TSW1400 User's Guide.
38
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Hardware Setup
www.ti.com
Figure 35. User Interface: Initial Setup Screen
•
Test Condition
Perform the steps in the order indicated in the following figure to set the test conditions:
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
39
Hardware Setup
www.ti.com
Figure 36. User Interface: Step-by-Step Setup
After completing the steps indicated, the following figure appears:
40
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Hardware Setup
www.ti.com
Figure 37. User Interface: Frequency Load Value to Signal Generator
Take the ADC Input frequency, and set the frequency of the signal generator to the noted ADC Input
frequency.
Set the Amplitude of the signal generator to -18 to -20 dBm (input amplitude should be between -1dBFS to
-3dbFS)
Set the Frequency of the Clock Generator to 40 MHz.
Set the Amplitude of the Clock Generator to 13 dBm.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
41
Hardware Setup
www.ti.com
Figure 38. User Interface: Final Setup Screen
Now the user can select the test channel, select the test type by choosing the Single Tone Tab, or Time
Domain Tab, and begin testing.
• Single Tone FFT
The Single Tone FFT test is shown in Figure 39. The larger central pane displays the FFT power
spectrum, whereas the calculated statistics are grouped into categories on the right of the screen.
Settings and inputs relevant to the test are entered in drop-down menus or text input boxes on the left
portion of the window.
42
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Hardware Setup
www.ti.com
Figure 39. User Interface: Single FFT Format
•
Time Domain
The Time Domain test is shown in Figure 40. The larger central pane displays the raw sampled data
whereas the calculated statistics are grouped into categories on the right of the screen. Settings and
inputs relevant to the test are entered in drop-down menus or text input boxes on the left portion of the
window.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TSW1400 for Evaluating AFE5801
43
Hardware Setup
www.ti.com
Figure 40. User Interface: Time Domain Format
•
EXCEL
The raw test sampled data can be saved to a file and processed by EXCEL or some other software.
4000
3500
3000
2500
2000
1500
1000
500
0
0
10
20
30
40
50
60
70
80
90
100
Figure 41. Plot of Saved Sample Data
44
TSW1400 for Evaluating AFE5801
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Appendix B
SLOU257B – October 2009 – Revised March 2015
High Speed Data Converter Pro (HSDCPro) GUI
Installation
Download the HSDCPro GUI Installer using this link: HSDCPro GUI
• Unzip the saved folder and run the installer executable to obtain the pop-up shown in Figure 42.
• Click the Install button.
Figure 42. HSDCPro Install (Begin)
•
Leave the destination directories as the default location, for the TSW1400GUI installation and press
the NEXT button as shown in Figure 43.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
High Speed Data Converter Pro (HSDCPro) GUI Installation
Copyright © 2009–2015, Texas Instruments Incorporated
45
Appendix B
www.ti.com
Figure 43. HSDCPro Install (Install Directory)
•
46
Read the License Agreement from Texas Instruments and select I accept the License Agreement and
press the Next button as shown in Figure 44.
High Speed Data Converter Pro (HSDCPro) GUI Installation
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Appendix B
www.ti.com
Figure 44. HSDCPro Install (TI License Agreement)
•
Read the License Agreement from National Instruments and select I accept the License Agreement
and press the Next button as shown in Figure 45.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
High Speed Data Converter Pro (HSDCPro) GUI Installation
Copyright © 2009–2015, Texas Instruments Incorporated
47
Appendix B
www.ti.com
Figure 45. HSDCPro Install (NI License Agreement)
•
48
Press the Next button as shown in Figure 46.
High Speed Data Converter Pro (HSDCPro) GUI Installation
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Appendix B
www.ti.com
Figure 46. HSDCPro Install (Start Installation)
•
The window shown in Figure 47 should appear indicating that the installation is in progress.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
High Speed Data Converter Pro (HSDCPro) GUI Installation
Copyright © 2009–2015, Texas Instruments Incorporated
49
Appendix B
www.ti.com
Figure 47. HSDCPro Install (Installation Progress)
•
50
The window shown in Figure 48 appears indicating Installation Complete. Press the Next button.
High Speed Data Converter Pro (HSDCPro) GUI Installation
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Appendix B
www.ti.com
Figure 48. HSDCPro Install (Installation Complete)
•
The window shown in Figure 49 appears briefly to complete the process.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
High Speed Data Converter Pro (HSDCPro) GUI Installation
Copyright © 2009–2015, Texas Instruments Incorporated
51
Appendix B
www.ti.com
Figure 49. HSDCPro Install (h)
•
As shown in Figure 50 a restart might be requested depending on whether or not the PC already had
the National Instruments MCR Installer. If requested, hit the Restart button to complete the installation.
Figure 50. HSDCPro Install
52
High Speed Data Converter Pro (HSDCPro) GUI Installation
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Revision History
www.ti.com
Revision History
Changes from A Revision (August 2011) to B Revision ................................................................................................ Page
•
Added Appendix B: High Speed Data Converter Pro (HSDCPro) GUI Installation.
............................................
45
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLOU257B – October 2009 – Revised March 2015
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Revision History
53
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan are NOT certified by
TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, User is required by Radio Law of Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
