User's Guide
SLOU338A – October 2012 – Revised November 2012
AFE5809EVM Evaluation Module
This document assists in evaluating the AFE5809 highly integrated analog front-end devices through the
use of the AFE5809EVM Evaluation Module. Included are setup instructions, printed-circuit board art, bill
of materials, and schematics.
13
Contents
Overview ..................................................................................................................... 3
Default Configuration ....................................................................................................... 3
Software Installation and Operation ...................................................................................... 4
Test Setup ................................................................................................................... 4
Power Up AFE5809 ........................................................................................................ 5
Launch AFE5809 GUI ...................................................................................................... 6
Launch TSW1400 GUI ..................................................................................................... 8
TEST AFE5809 .............................................................................................................. 8
8.1
Step 1: Time Domain .............................................................................................. 8
8.2
Step 2: Single Tone FFT ........................................................................................ 10
8.3
Step 3: Demodulator Mode ...................................................................................... 11
Hardware Setup, CW Mode .............................................................................................. 20
9.1
Step 1: Switch to CW Mode ..................................................................................... 21
9.2
Step 2: Apply Input and Observe Outputs .................................................................... 22
9.3
External Clock for CW Mode .................................................................................... 23
9.4
External ADC Sampling Clock .................................................................................. 23
External Vcntl .............................................................................................................. 26
Board Configuration ....................................................................................................... 27
11.1 I/O, Power Supply, and USB .................................................................................... 27
11.2 CW Mode, ADC Clock ........................................................................................... 28
11.3 Vcntl Control Input ................................................................................................ 29
11.4 LEDs ............................................................................................................... 30
11.5 Miscellaneous Test Points ....................................................................................... 31
EVM Printed-Circuit Board Layouts and Schematics ................................................................. 32
12.1 Schematics ........................................................................................................ 38
Bill of Materials ............................................................................................................. 48
1
AFE5809EVM Basic Configuration ....................................................................................... 3
2
Default HW Setup With Connection Between TSW1400EVM and AFE5809 ....................................... 4
3
LED Placement .............................................................................................................. 5
4
Default Page for AFE5809 GUI ........................................................................................... 6
5
Default ADC State .......................................................................................................... 7
6
TSW1400 GUI Load ........................................................................................................ 8
7
TSW1400 GUI Configuration .............................................................................................. 9
8
Ramp Waveform Output .................................................................................................. 10
9
GUI: Single FFT Format .................................................................................................. 11
10
Hardware Setup for Demodulation Mode Capture .................................................................... 12
11
Analog Sine Burst with 20 Cycles at 10 MHz .......................................................................... 12
1
2
3
4
5
6
7
8
9
10
11
12
List of Figures
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
1
www.ti.com
12
Demod Quick Load Buttons .............................................................................................. 13
13
Choose Trigger Mode ..................................................................................................... 14
14
MSB and LSB Mismatch Raw Data for Sine Test Mode ............................................................. 15
15
Sine Test Mode Output Seen in the Demodulator Plot ............................................................... 16
16
RF Test Mode Output ..................................................................................................... 17
17
Demod M=4, Both I and Q Data Test Mode Output Raw Data...................................................... 18
18
Demod M=4 I/Q Test Mode, Separated Data .......................................................................... 19
19
Setup for CW Mode ....................................................................................................... 20
20
Switching From Default (ADC) Mode Panel to CW Mode Panel .................................................... 21
21
CW Outputs ................................................................................................................ 22
22
Relevant Capacitors for CW Mode, Top and Bottom Side ........................................................... 23
23
External ADC Sampling Clock Configuration .......................................................................... 24
24
GUI Screen for Windowing Option Selection .......................................................................... 24
25
External Vcntl Configuration
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
.............................................................................................
I/O, PWR, and USB Connector ..........................................................................................
AFE5809EVM Jumper Locations ........................................................................................
Vcntl .........................................................................................................................
AFE5809EVM LED Location .............................................................................................
AFE5809EVM Test Point Locations ....................................................................................
Top Layer - Signal .........................................................................................................
Second Layer - Ground ...................................................................................................
Third Layer - Power .......................................................................................................
Fourth Layer - Signal......................................................................................................
Fifth Layer - Ground .......................................................................................................
Bottom Layer - Signal .....................................................................................................
Schematic (Sheet 1 of 10)................................................................................................
Schematic (Sheet 2 of 10)................................................................................................
Schematic (Sheet 3 of 10)................................................................................................
Schematic (Sheet 4 of 10)................................................................................................
Schematic (Sheet 5 of 10)................................................................................................
Schematic (Sheet 6 of 10)................................................................................................
Schematic (Sheet 7 of 10)................................................................................................
Schematic (Sheet 8 of 10)................................................................................................
Schematic (Sheet 9 of 10)................................................................................................
Schematic (Sheet 10 of 10) ..............................................................................................
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
List of Tables
1
Configuration for Clock Capacitors ...................................................................................... 23
2
I/O, Power, and USB ...................................................................................................... 27
3
CW Mode, ADC Clock
4
5
6
7
2
...................................................................................................
CW Mode and Vcntl .......................................................................................................
LED Indicators .............................................................................................................
Test Points .................................................................................................................
Bill of Materials.............................................................................................................
AFE5809EVM Evaluation Module
29
29
30
31
48
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Overview
www.ti.com
1
Overview
This document is intended as a step-by-step guide through the AFE5809EVM Evaluation Module (EVM)
setup and test. The EVM is shipped with a default configuration from the manufacturer. With this
configuration, the onboard CMOS clock is used for a analog-to-digital converter sampling clock; the
onboard oscillator is used for CW mode operation. No external clock generator is required. Users need to
provide the input signal for measurement from a signal generator.
Detail explanation regarding the jumpers, connectors, and test points appear in Section 11. The graphical
user interface (GUI) can be downloaded from the TI Web site.
2
Default Configuration
Figure 1 shows the default configuration of the EVM from the factory. The accompanying list identifies the
basic components on the EVM board.
Figure 1. AFE5809EVM Basic Configuration
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
3
Software Installation and Operation
www.ti.com
1. P1 – Power supplies connector ±5 V.
2. JP1, JP2, and JP3 are set to enable 3.3-V, 1.8-V, and 5-V power supplies to the device.
3. JP9: Enables onboard CMOS clock.
4. JP10: Power supply for onboard CMOS clock oscillator.
5. JP15: Enables onboard Vcntl.
6. JP59: Connects 1.4-V supply (LED_LDO should be lit).
7. P17: Disables PDN_Global.
8. P15: Choose the device Common Mode for the I/V Amp Common Mode.
9. P16: Chooses Vss as –5 V for low-side power supply on the I/V Amp.
10. JP16 is set to enable the demodulator internal LDO, as shown in Figure 1.
3
Software Installation and Operation
The AFE5809EVM GUI (SLOC254) can be downloaded from the TI Web site. Follow the directions in the
Read Me First.pdf file to install the GUI and device driver.
4
Test Setup
Two EVMs are required to evaluate the AFE5809 device. Figure 2 shows the exact setup of these two
boards and external connectors. For the default configuration shown in Figure 1, having an external
sampling clock and external Vcntl supply is unnecessary. The onboard CMOS clock and onboard Vcntl
are used.
Figure 2. Default HW Setup With Connection Between TSW1400EVM and AFE5809
4
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Power Up AFE5809
www.ti.com
5
Power Up AFE5809
Power up the AFE5809EVM by applying +5 V and –5 V to the P1 connector. After power up is complete,
five green LEDS and three red LEDS turn on as shown in Figure 3.
Figure 3. LED Placement
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
5
Launch AFE5809 GUI
6
www.ti.com
Launch AFE5809 GUI
Launch the AFE5809 graphic user interface (GUI), Figure 4. After successful launch, the status bar at the
bottom should say "Ready for new command". Then, LED41 and LED42 turn off and the rest of the LEDS
remain on. The GUI automatically configures the default setup. Select the ADC page to observe the
default condition.
Figure 4. Default Page for AFE5809 GUI
6
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Launch AFE5809 GUI
www.ti.com
Figure 5 shows the Default Condition on the ADC window.
Figure 5. Default ADC State
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
7
Launch TSW1400 GUI
7
www.ti.com
Launch TSW1400 GUI
Launch the TSW1400 GUI. A Pop-up window should prompt you to connect to the EVM if it is connected
via USB. If a different message or an error message appears, contact the TI FAE. If the GUI connects
properly, the status at the bottom says "Connected" in Green.
Select AFE5809_09_14b for the firmware by clicking the blue arrow.
Click Yes to update firmware on the board. This can take about 30 seconds.
ADC Sampling Rate in lower left should be set to 40 MHz; this is the onboard CMOS clock frequency. Set
this appropriately if using an external clock.
ADC Input Frequency – enter 2M.
Check the "Auto Calculation of Coherent Frequency" box in the lower left to display actual coherent
frequency based on user input. This is only needed for signal integrity testing like SNR.
Figure 6. TSW1400 GUI Load
8
TEST AFE5809
8.1
Step 1: Time Domain
•
•
8
Select the Time Domain page from the TSW1400 GUI.
Uncheck Overlay 'Unwrap Waveform'.
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
Figure 7. TSW1400 GUI Configuration
•
From the AFE5809 GUI, go to the ADC page, and then select Ramp.
•
Press the Capture button on the TSW1400 GUI. This displays a ramping waveform on the TSW1400
GUI display area as shown in Figure 8.
Verify that Maximum value is 16383 for 14-bit mode.
Repeat for Channel 2 and Channel 8.
If each channel has the output as shown in Figure 8, proceed with the next step; otherwise, contact the
TI FAE to troubleshoot the problem.
On the AFE5809 GUI, change Test Pattern from Ramp to None for the next step.
•
•
•
•
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
9
TEST AFE5809
www.ti.com
Figure 8. Ramp Waveform Output
8.2
Step 2: Single Tone FFT
•
•
•
•
•
•
•
10
Select Frequency from the display control on the TSW1400 GUI to display the FFT.
Connect Channel 1 of the AFE5809EVM to a signal generator through a BP filter. If a BP filter is not
present, the result is not good.
Set the amplitude of the signal generator to -25 dBm.
Set the frequency of the signal generator to the value in the "ADC Input Target Frequency" field of the
TSW GUI.
Change the window option to Hanning if using the onboard clock. This is because the input signal and
the onboard CMOS clock are noncoherent.
Press the Capture button to get the test result.
Repeat for Channel 2 through Channel 8.
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
Figure 9. GUI: Single FFT Format
8.3
Step 3: Demodulator Mode
The AFE5809 has a special demodulation and decimation mode whose main purpose is to reduce the
LVDS data rate and improve overall system power efficiency. The device includes some built-in test
modes to verify that demodulator block is working correctly.
First, setup hardware as follows:
• USB cable connected to both EVMs
• External ADC clock enabled and used
• Sync external clock to analog sine burst source
• Connect analog input waveform to input channel 1
• Connect trigger from sine burst source that is synced with the analog signal to TX_Sync_in at J11
• Connect same trigger to TSW1400 EVM trigger input at J11
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
11
TEST AFE5809
www.ti.com
Figure 10. Hardware Setup for Demodulation Mode Capture
First, setup an analog input waveform at 10 MHz and 20 cycles similar to Figure 11 (Tektronix AFG3102 is
recommended). Adjust amplitude until there is no clipping of waveform.
Figure 11. Analog Sine Burst with 20 Cycles at 10 MHz
12
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
The ADC must be set to the proper configuration for Demodulation:
• ADC format must be MSB First, 2's Complement
• LVDS Rate must be set to 16X
• Choose any demodulator test mode from the following buttons: Sine Test Mode, RF Test Mode,
Coefficient Test Mode and Demod M=4 I/Q Test Mode.
• For modes and options, load a text using "Exec CMD File".
Figure 12. Demod Quick Load Buttons
Next, capture triggered data from the TSW capture card:
• Change TSW1400 GUI Firmware setting to "AFE5808_09_16b"
• Enable Trigger Mode in TSW GUI
• Capture data by pressing the Read DDR Memory button. (In triggered mode, press this button twice to
capture updated data). The output on the plot does not make any sense because of the LSB and MSB
disconnect between the AFE5809 GUI and the TSW GUI. Also, if the trigger is not strong enough to
drive a 50-Ω load, the R83 may need to be removed from the AFE EVM.
Next, import the TSW data into the AFE5809GUI for data processing:
• Go back to the AFE GUI and choose under the Demodulator main tab, choose "Demodulator Plot".
This should be set-up for M=4, Channel 1, MSB mode, Record size should be 2000. If a capture has
taken place in the TSW GUI, then click "TSW capture" on the Demodulator Plot Tab and the Raw Data
Plot updates with the data from the TSW memory. If the "MSB" button is true, then the raw data should
make sense. Note: Do not choose "2's complement" in Sine Test Mode.
• Try this process (TSW GUI Capture twice -> AFE GUI "TSW Capture") for the other test modes.
• Under RF Test Mode, the output should look similar to the input.
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
13
TEST AFE5809
•
www.ti.com
Under Demod M=4 I/Q Test Mode, also look at the "Separate Data" tab to view the I/Q separated
Data.
Figure 13. Choose Trigger Mode
14
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
Figure 14. MSB and LSB Mismatch Raw Data for Sine Test Mode
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
15
TEST AFE5809
www.ti.com
Figure 15. Sine Test Mode Output Seen in the Demodulator Plot
16
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
Figure 16. RF Test Mode Output
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
17
TEST AFE5809
www.ti.com
Figure 17. Demod M=4, Both I and Q Data Test Mode Output Raw Data
18
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TEST AFE5809
www.ti.com
Figure 18. Demod M=4 I/Q Test Mode, Separated Data
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
19
Hardware Setup, CW Mode
9
www.ti.com
Hardware Setup, CW Mode
Figure 19. Setup for CW Mode
20
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware Setup, CW Mode
www.ti.com
9.1
Step 1: Switch to CW Mode
•
•
•
Go to the CW Mode page.
Check CW Mode Enable. Then LED41, LED42, and LED43 on AFE5809EVM all illuminate.
Select 500 Ω for the gain control feedback resistor.
Figure 20. Switching From Default (ADC) Mode Panel to CW Mode Panel
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
21
Hardware Setup, CW Mode
9.2
www.ti.com
Step 2: Apply Input and Observe Outputs
•
•
Apply an analog signal (2.51 M, –10 dBm) to any analog input SMA.
The CW outputs (J12, J13) display the frequency I and Q signals at 10 kHz as shown in Figure 21.
The GUI Gain Control Feedback Resistor can be used to vary the amplitude of the outputs.
Figure 21. CW Outputs
22
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware Setup, CW Mode
www.ti.com
9.3
External Clock for CW Mode
The CW mode clocks can be supplied from J9 (X16/X8/X4/X1) and J10 (X1) using external signal
generators. The manufacture default setup uses ON BOARD CLOCK, with which C154, C155, C156, and
C157 are installed. To switch to an external clock, these four capacitors must be uninstalled and
capacitors C49,C50,C52, and C53 must be installed. The following table shows the configuration for these
eight capacitors.
Table 1. Configuration for Clock Capacitors
Capacitor
Onboard Clock
External Clock
Comments
C27
Uninstalled
Installed
Top layer of the EVM
C28
Uninstalled
Installed
Bottom layer of the EVM
C100
Uninstalled
Installed
Bottom layer of the EVM
C102
Uninstalled
Installed
Top layer of the EVM
C29
Installed
Uninstalled
Top layer of the EVM
C30
Installed
Uninstalled
Top layer of the EVM
C25
Installed
Uninstalled
Top layer of the EVM
C26
Installed
Uninstalled
Top layer of the EVM
Figure 22. Relevant Capacitors for CW Mode, Top and Bottom Side
9.4
External ADC Sampling Clock
To
1.
2.
3.
use the external clock generator to test the AFE5809, perform the following steps.
Reconfigure JP9 as shown in Figure 23. The rest of the jumpers remain the same.
Connect the external generator as shown in Figure 23.
Set the generator output to 65 MHz, 13 dBm.
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
23
Hardware Setup, CW Mode
www.ti.com
Figure 23. External ADC Sampling Clock Configuration
4. If the generators for the ADC clock and input signal are synchronous, then choose Rectangular as the
Windowing option; otherwise, use Hanning or Hamming. Notice the spectrum spreading with noncoherence.
Figure 24. GUI Screen for Windowing Option Selection
24
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Hardware Setup, CW Mode
www.ti.com
5. The test procedure is the same for the CMOS ADC clock.
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
25
External Vcntl
10
www.ti.com
External Vcntl
•
•
JP15 needs to be reconfigured to short the leftmost two pins.
A DC Voltage source is required to be connected to J14.
Figure 25. External Vcntl Configuration
26
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Board Configuration
www.ti.com
11
Board Configuration
11.1 I/O, Power Supply, and USB
Figure 26. I/O, PWR, and USB Connector
Table 2. I/O, Power, and USB
Connector
Description
J1 through J8
Analog Input signals for Ch1 through Ch8. Connect to a signal generator. A bandpass filter must be applied
between the generator and the SMA to get a better result. (See Figure 1.)
P1/JP6
P1 is the +5-V and –5-V power supply connector. JP6 is the test point for +5-V/-5-V power supply.
JP3
Onboard 5-V enable. The configuration must be set up as shown in Figure 2 in order to use onboard 5-V
supply.
TP-5V
-5-V supply test point
+5VA
+5-V supply test point
JP1
Onboard +1.8-V enable. The configuration must be set up as shown in Figure 2 in order to use the onboard
+1.8 V.
JP2
Onboard 3.3-VA enable. The configuration must be set up as shown in Figure 2 in order to use the onboard
3.3 V.
TP18VD
+1.8-VD supply test point
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
27
Board Configuration
www.ti.com
Table 2. I/O, Power, and USB (continued)
Connector
Description
TP33VD
+3.3-VD supply test point
TP33VA
+3.3-VA supply test point
TP14VD
+1.4-VD supply test point
TP1 through TP4
Ground test points
USB1
USB interface connector
P13,P14
Test points for USB data bus: From pin 1 to pin 9, the signals are D0, D4, D2, D1, D7, D5, D6, and D3
11.2 CW Mode, ADC Clock
Figure 27. AFE5809EVM Jumper Locations
28
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Board Configuration
www.ti.com
Table 3. CW Mode, ADC Clock
Clock
Type
Reference
Designator
Description
J9/J10
External CW Mode clock. The default is using onboard oscillator.
J12
JP52/JP53
CW Mode
J13
JP56/JP57
ADC
CW output for I-channel via an external operational amplifier. The EVM has converted the
differential signal CW_IP_OUTP and CW_IP_OUTM into this single-ended output through an
operational amplifier.
To observe CW_IP_OUTP and CW_IP_OUTM before the external operational amplifier, probe
JP52 and JP53.
CW output for V-channel via an external operational amplifier. The EVM has converted the
differential signal CW_VP_OUTP and CW_VP_OUTM into this single-ended output through an
operational amplifier.
To observe CW_VP_OUTP and CW_VP_OUTM before the external operational amplifier, probe
JP56 and JP57.
JX1
This connector shows the signals of J12 and J13 simultaneously.
JP9/JP10
JP9 selects on_board_ADC CMOS clock or external clock from J14. Default setup in Figure 19
uses onboard CMOS clock. Set it to the other side to use the external clock source.
Short to power up onboard CMOS clock
J14
External ADC clock Input
11.3 Vcntl Control Input
Figure 28. Vcntl
Table 4. CW Mode and Vcntl
Connector
Description
JP15
Choose onboard Vcntl or external Vcntl. The default setup uses onboard Vcntl.
J14
External Vcntl input. The range is from 0 V to 1.5 V.
VR2
Onboard Vcntl adjustment. Use JP15 pin 3 which has the text On-Board to monitor the Vcntl voltage level.
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
29
Board Configuration
www.ti.com
11.4 LEDs
The AFE5809EVM has seven LEDs. Their locations are shown in Figure 29. Their ON and OFF states
demonstrate the normal operation of the power supplies and the PLL status of the clock buffer.
Figure 29. AFE5809EVM LED Location
Table 5. LED Indicators
Reference Designator
Power Supply
Color
LED-5V
–5 V
Green
LED5V
+5 V
Green
LED3.3VD
+3.3 VD
Orange
LED3.3VA
+3.3 VA
Green
LED1.8V
+1.8 V
Green
LED_LDO
+1.4V
Green
LED41
LED42
30
AFE5809EVM Evaluation Module
Clock Buffer Status Indicator
Red
Red
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Board Configuration
www.ti.com
11.5 Miscellaneous Test Points
Figure 30. AFE5809EVM Test Point Locations
Table 6. Test Points
Reference Designator
Description
TP11,TP14.TP15
AFE5809 device test pin DNC1, 2, and 3. Pins L5, M5 and M8
JP19
REFM voltage input
JP44
RESET input. Short to reset AFE5809.
JP20
REFP voltage input
JP21
REF_IN voltage input
TP12
SDOUT
TP3-9
SMA input probes
TP5V, TP18VD, TP33VD, TP33VA, TP-5V, -5VA,
+5VA, TP14VD, DVDD_LDO1
Power supply test points
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
31
EVM Printed-Circuit Board Layouts and Schematics
12
www.ti.com
EVM Printed-Circuit Board Layouts and Schematics
Figure 31 through Figure 36 show the six layers of the AFE5809EVM board.
Figure 31. Top Layer - Signal
32
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Figure 32. Second Layer - Ground
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
33
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Figure 33. Third Layer - Power
34
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Figure 34. Fourth Layer - Signal
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
35
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Figure 35. Fifth Layer - Ground
36
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Figure 36. Bottom Layer - Signal
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
AFE5809EVM Evaluation Module
37
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
12.1 Schematics
Power
Figure 37. Schematic (Sheet 1 of 10)
38
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
AFE5809 DEVICE
Figure 38. Schematic (Sheet 2 of 10)
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
39
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
VCA INPUT
ADC OUTPUT
Figure 39. Schematic (Sheet 3 of 10)
40
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Clock Buffer
Figure 40. Schematic (Sheet 4 of 10)
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
41
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
ADC CLOCK
Figure 41. Schematic (Sheet 5 of 10)
42
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
CW CLK
16X
1X
Figure 42. Schematic (Sheet 6 of 10)
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
43
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
VCON SINGLE TO DIFFERENTIAL CONVERTER
Figure 43. Schematic (Sheet 7 of 10)
44
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
CW Mixer Out
Figure 44. Schematic (Sheet 8 of 10)
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
45
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
Serial Interface
There are two ground planes here.
We isolate the USB circuit from
the rest of the board. The circuits are only
coupled through the opto-isolators.
Figure 45. Schematic (Sheet 9 of 10)
46
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVM Printed-Circuit Board Layouts and Schematics
www.ti.com
CW I/V Amp
ALL Bypass Caps in
this circuit need to be
tied close to the pin.
This Circuit provides 3
options for populating
Op-Amps for maximum flexibility
Figure 46. Schematic (Sheet 10 of 10)
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
47
Bill of Materials
13
www.ti.com
Bill of Materials
Table 7. Bill of Materials
ITEM
QTY
MFG
MFG PART#
REF DES
1
82
AVX
0402YC104KAT2A
C17, C25, C26, C29, C30, C33, C37, C40, CAP,SMT,0402
C49, C51, C52, C56, C59, C62, C64, C76,
C78, C80, C82, C84, C86, C94, C95, C96,
C97, C98, C99, C101, C103, C105, C106,
C110, C111, C112, C113, C114, C115,
C120, C122, C124, C125, C130, C131,
C132, C133,C134, C135, C136, C137,
C138, C139, C140, C141, C142, C143,
C144, C145, C146, C147, C148, C149,
C150, C153, C154, C155, C160, C162,
C163, C164, C165, C166, C167, C170,
C171, C173, C174, C177, C178, C179,
C180
CAPACITOR,SMT,0402,C
ER,16V,10%,0.1uF
2
2
AVX
0402YC471KAT2A
C53,C60
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,16V,10%,470pF
3
2
AVX
0402YC222KAT2A
C10, C74
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,16V,10%,2200pF
4
11
KEMET
C0402C104K8PAC
C1, C54, C57, C67, C68, C69, C152,
C157, C158, C168, C181
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,0.1uF,10V,10%,X5R
5
4
KEMET
C0402C152J5GACTU
C73, C89
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ERAMIC,1500pF,50V,5%,
C0G/NP0
6
8
TDK
C1005X5R0J105M
C77, C79, C81, C83, C85, C87, C104,
C126
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,1.0uF,6.3V,20%,X5R
7
4
PANASONIC
ECJ-0EB1A105M
C71, C72, C117, C127
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ERAMIC,1.0uF,10V,20%,X
5R
8
8
PANASONIC
ECJ-0EB1C153K
C107, C108, C109, C116, C118, C119,
C121, C123
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,15000pF,16V,10%,X7R
9
1
PANASONIC
ECJ-0EB1H102K
C32
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,1000pF,50V,10%,X7R
10
4
PANASONIC
ECJ-0EB1H332K
C22, C23, C24, C41
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,3300pF,50V,10%,X7R
11
2
PANASONIC
ECJ-0EC1H470J
C175, C176
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,47pF,50V,5%,NPO
12
1
PANASONIC
ECJ-0EC1H820J
C156
CAP,SMT,0402
CAPACITOR,SMT,0402,C
ER,82pF,50V,5%,NPO
13
9
AVX
06033C104JAT2A
C5, C7, C8, C12, C15, C88, C90, C91,
C92
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,0.1uF,25V,5%,X7
R
48
AFE5809EVM Evaluation Module
DESCRIPTION
VALUE or FUNCTION
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
14
7
AVX
0603YD105KAT2A
C38, C39, C58, C63, C159, C161, C172
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,1.0uF,16V,10%,X
5R
15
1
TAIYO YUDEN
AMK107BJ226MA-T
C9
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,22uF,4V,20%,X5
R
16
1
PANASONIC
ECJ-1VB0J106M
C4
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,10uF,6.3V,20%,X
5R
17
3
PANASONIC
ECJ-1VB1C105K
C75, C93, C129
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,1.0uF,16V,10%,X
5R
18
2
MURATA
GRM188C80G475KE19
C6, C11
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,4.7uF,4V,10%,X6
S ( TI-F )
19
1
TAIYO YUDEN
JMK107BJ106MA-T
C31
CAP,SMT,0603
CAPACITOR,SMT,0603,C
ERAMIC,10uF,6.3V,20%,X
5R
20
4
KEMET
C0805C332F3GACTU
C18, C19, C45, C46
CAP,SMT,0805
CAPACITOR,SMT,0805,C
ERAMIC,3300pF,25V,1%,
C0G(NP0)
21
6
KEMET
C1206C226K8PAC
C20, C21, C35, C36, C47, C48
CAP,SMT,1206
CAPACITOR,SMT,1206,C
ERAMIC,22uF,10V,10%,X
5R
22
1
AVX
1210ZG226ZAT2A
C169
CAP,SMT,1210
CAP,22uF,10V,+80~-20%
23
4
VISHAY SPRAGE
293D226X9016D2T
C43
CAP,SMT,7343
CAP,TAN,SMT,
22uF,16V,+/-10%,-55~85C
24
4
VISHAY SPRAGE
293D226X9016D2T
C16, C34, C128
CAP,SMT,7343
CAP,TAN,SMT,
22uF,16V,+/-10%,-55~85C
25
1
AVX
TACH106M010R
C50
CAP,SMT,TAN,0805
CAP,SMT,TAN,0805,10uF,
10V,20%,H-CASE
26
8
AVX
TPSC226K016R0375
C2, C3, C55, C61, C65, C66, C70, C151
CAPACITOR,SMT,TA
NT
10%, 16V, 22uF
27
9
AMPHENOL
901-144-8
J1, J3, J5, J7, J9, J10, J11, J12, J13
CONNECTOR,SMA
SMA COAX STRAIGHT
PCB CURRENT P/N IS
901-144-8RFX
28
1
MURATA
BLM15BD102SN1D
FB16
FERRITE
BEAD,SMT,0402
FERRITE
BEAD,SMT,0402,1K
OHM,200mA
29
17
STEWARD
HI0805R800R-00
FB1, FB2, FB3, FB4, FB5, FB6, FB7, FB8, FERRITE
FB9, FB10, FB11, FB12, FB13, FB14,
BEAD,SMT,2P
FB15, FB17, FB18
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
FERRITE,SMT,0805,80
OHM@100MHz,5A
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
49
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
30
1
MOLEX
39357-0003
P1
HEADER, THRU, 3P
HEADER, THRU, POWER,
3P,3.5MM, EUROSTYLE
31
1
SAMTEC
QTH-060-01-L-D-A
P10
HEADER,SMT,120P
HEADER,SMT,120P,0.5m
m,FEM,2BANK,RECEPTA
CLE,168/198H
32
1
SAMTEC
TSW-103-07-G-D
JP9
HEADER,THU
HEADER,THU,6P,2X3,MA
LE,DUAL
ROW,100LS,100TL
33
2
SAMTEC
TSW-104-07-G-D
JP1, JP2
HEADER,THU
HEADER,THU,8P,2X4,MA
LE,DUAL
ROW,100LS,100TL
34
3
TYCO ELECTRONICS
4-103239-0X5
J16, JP50, JP51
HEADER,THU,5P
HEADER, 1X5 .1CTRS
35
2
SPC TECH
8431-1x9
P13, P14
HEADER,THU,9P
HEADER,THU,MALE,0.1L
S,9P,1X9,335H,120TL
36
11
TYCO ELECTRONICS
4-103239-0x2
JP10, JP16, JP17, JP19, JP20, JP21,
JP29, JP44, JP58, JP4A, JP4B
HEADER,THU,JUMPE
R
MALE,2PIN,.100CC MAKE
FROM 4-103239-0x2
37
11
TYCO ELECTRONICS
4-103239-0x3
JP3, JP6, JP15, JP52, JP53, JP56, JP57,
JP59, P15, P16, P17
HEADER,THU,JUMPE
R
MAKE FROM 4-103239-0
38
3
NATIONAL SEMI
LME49990MA/NOPB
U3, U5, U7
IC,SMT,8P
ULTRA LOW
DISTORTION ULTRA
LOW NOISE OPAMP
39
1
TEXAS INSTRUMENTS
CDCM7005RGZ
CLK_BUF
IC,SMT,QFN-48
3.3-V HIGH
PERFORMANCE CLOCK
SYNTHESIZER AND
JITTER CLEANER
40
3
TI
ISO7240MDW
U16, U20, U21
IC,SMT,SOIC-16W
QUAD DIGITAL
ISOLATORS
41
1
TI / BURR-BROWN
OPA211AID
U13
IC,SMT,SOIC-8
1.1nV/Hz NOISE LOW
POWER PRECISION
OPERATIONAL
AMPLIFIER
42
1
TI
OPA2614ID
U10
IC,SMT,SOIC-8
DUAL HI GAIN BWIDTH
HI OUTPUT CURRENT
OPAMP WITH CURRENT
LIMIT
43
1
BURR-BROWN / TI
REF5025AID
U2
IC,SMT,SOIC-8
LOW-NOISE VERY LOW
DRIFT PRECISION
VOLTAGE
REFERENCE,2.5V
44
1
TI
TPS79601DCQR
U18
IC,SMT,SOT223-6
ULTRALOW-NOISE HI
PSRR FAST RF 1-A LDO
LINEAR REGULATOR,1.25.5V
50
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
45
1
TI
TPS79618DCQR
U14
IC,SMT,SOT223-6
ULTRALOW-NOISE HI
PSRR FAST RF 1-A LDO
LINEAR
REGULATOR,1.8V
46
2
TI
TPS79633DCQR
U1, U12
IC,SMT,SOT223-6
ULTRALOW-NOISE HI
PSRR FAST RF 1-A LDO
LINEAR
REGULATOR,3.3V
47
1
TI
SN74LVC1G06DBV
U11
IC,SMT,SOT23-5
SINGLE INVERTER
BUFFER / DRIVER WITH
OPEN-DRAIN OUTPUT
48
1
FTDI
FT245RL
U19
IC,SMT,SSOP-28
USB FIFO IC
INCORPORATE
FTDICHIP-ID SECURITY
DONGLE
49
3
PANASONIC
LNJ208R82RA
LED41, LED42, LED43
LED,SMT,0603
LED,SMT,0603,ULTRA
BRIGHT RED,1.92V
50
5
PANASONIC
LNJ308G8PRA
LED-5V, LED33VA, LED33VD, LED5V,
LED_LDO
LED,SMT,0603
LED,SMT,0603,PURE
GREEN,2.03V
51
1
PANASONIC
LNJ808R8ERA
LED18VA
LED,SMT,0603
LED,SMT,0603,ORANGE,
1.8V
52
1
ECS
ECS-3953M-400-BN
U17
OSCILLATOR,SMT,4P OSC,SMT,3.3V,50ppm,40~85C,5nS,40.000 MHz
53
7
VENKEL
CR0402-16W-000T
R2, R5, R14, R63, R71, R93
RES,SMT,0402
RESISTOR,SMT,0402,0
OHM,1/16W,ZERO
JUMPER
54
2
VISHAY
CRCW04021001F100
R50, R92
RES,SMT,0402
RESISTOR,SMT,0402,1K,
1/16W,1%,100ppm
55
1
VISHAY
CRCW04021002F100
R95
RES,SMT,0402
RESISTOR,SMT,0402,10K
,1/16W,1%,100ppm
56
2
VISHAY
CRCW04022002F100
R44, R91
RES,SMT,0402
RESISTOR,SMT,0402,20K
,1/16W,1%,100ppm
57
3
VISHAY
CRCW04024990F100
R80, R81, R82
RES,SMT,0402
RESISTOR,SMT,0402,499
OHM,1/16W,1%,100ppm
58
1
VISHAY
CRCW04025110F100
R58
RES,SMT,0402
RESISTOR,SMT,0402,511
OHM,1/16W,1%,100ppm
59
1
PANASONIC
ERJ-2GE0R00X
R56
RES,SMT,0402
RESISTOR/JUMPER,SMT,
0402,0 OHM,5%,1/16W
60
6
PANASONIC
ERJ-2GEJ131
R28, R29, R30, R32, R43
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,130
61
4
PANASONIC
ERJ-2GEJ391
R51, R52, R54, R55
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,390
62
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
51
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
63
6
PANASONIC
ERJ-2GEJ820
R23, R24, R26, R27, R34
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,82
64
8
PANASONIC
ERJ-2RKF1000X
R25, R40, R42, R76, R78, R84, R85, R89
RES,SMT,0402
RESISTOR,SMT,0402,100
OHM,1%,1/10W
65
3
PANASONIC
ERJ-2RKF3320X
R59, R90, R94
RES,SMT,0402
RESISTOR,SMT,0402,332
OHM,1%,1/16W
66
3
PANASONIC
ERJ-2RKF49R9X
R83, R88, R96
RES,SMT,0402
RESISTOR,SMT,0402,49.
9 OHM,1%,1/16W
67
2
VISHAY
CRCW0603200F
R53, R57
RES,SMT,0603
RESISTOR,SMT,0603,1%,
1/10W,200 OHM
68
1
VISHAY
CRCW06033012F
R87
RES,SMT,0603
RESISTOR,SMT,0603,1%,
1/10W,30.1K
69
1
VISHAY
CRCW06034321F
R86
RES,SMT,0603
RESISTOR,SMT,0603,1%,
1/10W,4.32K
70
1
PANASONIC
ERJ-3GSYJ153
R60
RES,SMT,0603
RESISTOR,SMT,0603,5%,
1/10W,15K
71
2
VISHAY
TNPW06034750BT9
R3, R12
RES,SMT,0603
RESISTOR,SMT,0603,THI
N FILM,475 OHM
0.1%,1/10W,25ppm
72
8
VISHAY
TNPW06034990BT9
R18, R19, R38, R39, R46, R47, R48, R49
RES,SMT,0603
RESISTOR,SMT,0603,THI
N FILM,499 OHM
0.1%,1/10W,25ppm
73
3
VISHAY
TNPW060349R9BEEN
R9, R36, R37
RES,SMT,0603
RESISTOR,SMT,0603,THI
N FILM,49.9
OHM,0.1%,1/10W
74
1
KYCON
STX-3000
JX1
STEREO PHONE
JACK,THU,3 PIN
STEREO PHONE
JACK,THU,3 PIN,3.5mm
75
7
KEYSTONE ELECTRONICS
5000
TP2, TP13, TP14VD, TP18VD, TP33VA,
TP33VD, TP5V
TESTPOINT,THU,1P
TESTPOINT,THU,MINIAT
URE,0.1LS,120TL, RED
76
4
KEYSTONE ELECTRONICS
5001
GND1, GND2, GND3, GND4
TESTPOINT,THU,1P
TESTPOINT,THU,MINIAT
URE,0.1LS,120TL, BLACK
77
2
KEYSTONE ELECTRONICS
5002
TP1, TP-5V
TESTPOINT,THU,1P
TESTPOINT,THU,MINIAT
URE,0.1LS,120TL, WHITE
78
13
KEYSTONE ELECTRONICS
5004
TP3, TP4, TP5, TP6, TP7, TP8, TP9,
TP10, TP11, TP12, TP14, TP15, TP16
TESTPOINT,THU,1P
TESTPOINT,THU,MINIAT
URE,0.1LS,120TL,
YELLOW
79
3
MINI-CIRCUITS
ADT4-1WT
T1, T2, T3
TRANSF,SMT,6P
RF TRANSFORMER
WIDEBAND, 2-775 MHz,
50 OHM
80
2
BOURNS
3296W-1-103
VR2, VR3
TRIMPOT,THU,3P
TRIMPOT,THU,10K,10%,0
.5W,100ppm,25T
52
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
81
1
BOURNS
3296W-1-205
82
4
Digi-Key
83
4
84
VR1
TRIMPOT,THU,3P
TRIMPOT,THU,2M,10%,0.
5W,100ppm,25T
29311K-ND
SCREW STEEL M3
THR 6MM
SCREW STEEL M3 THR
6MM
Digi-Key
24436K-ND
STANDOFF HEX M3
THR ALUM 18MM
STANDOFF HEX M3 THR
ALUM 18MM
20
Molex
15-29-1025
SHUNT-JUMPER
CONN SHUNT CLOSED
TOP .100 GOLD
85
2
SUSUMU
RG1005N152B
R10, R64
RES,SMT,0402
RESISTOR,SMT,0402,THI
N FILM,1.5
K,0.1%,1/16W,10ppm,Tole
rance important
86
4
SUSUMU
RG1005N202B
R61, R74
RES,SMT,0402
RESISTOR,SMT,0402,THI
N FILM,2
K,0.1%,1/16W,10ppm,Tole
rance important
87
4
SUSUMU
RG1005N202B
R4, R13
UNINSTALLED
RESISTOR,SMT,0402,THI
N FILM,2
K,0.1%,1/16W,10ppm,UNI
NSTALLED
88
2
TI
THS4131ID
U15, VCON_OPAMP
UNINSTALLED
HIGH-SPEED LOW
NOISE DIFFERENTIAL I/O
AMPLIFIERS
UNINSTALLED
89
6
UNINSTALLED
0402YC104KAT2A(UN)
C27, C28, C42, C44, C100, C102,C13,
C14
UNINSTALLED
UNINSTALLED
90
11
UNINSTALLED
CRCW04020000Z0ED(UN)
R1, R6, R7, R8, R11, R15, R16, R17,
R62, R72, R73, R75
UNINSTALLED
UNINSTALLED
91
6
PANASONIC
ERJ-2GEJ820
R33
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,82
(UNINSTALLED)
92
6
PANASONIC
ERJ-2GEJ131
R31
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,130
(UNINSTALLED)
93
1
PANASONIC
ERJ-2GEJ161
R35
RES,SMT,0402
RESISTOR,SMT,0402,THI
CK FILM,5%,1/16W,160
(UNINSTALLED)
94
3
TI
LMH6629SDE/NOPB
U4, U6, U8
IC,SMT,DFN-8
ULTRA-LOW
NOISE,PRECISION
OPERATIONAL
AMPLIFIERS
95
4
PANASONIC
ERJ-3GSYJ102(UN)
R20, R21, R22, R41
RES,SMT,0603
( UNINSTALLED PART )
96
8
PANASONIC
ERJ-2GEJ49R9(UN)
R65, R66, R67, R68, R69, R70, R77, R79
RES,SMT,0402
( UNINSTALLED PART )
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
AFE5809EVM Evaluation Module
Copyright © 2012, Texas Instruments Incorporated
53
Bill of Materials
www.ti.com
Table 7. Bill of Materials (continued)
97
1
VISHAY
CRCW04024701F100
R45
RES,SMT,0402
RESISTOR,SMT,0402,4.7
K,1/16W,1%,100ppm
(UNINSTALLED)
98
1
ADVANCED CONNECTEK
MNE20-5K5P10
USB1
CONN,SMT,5P
MINI-AB USB OTG
RECEPTACLE R/A SMT
TYPE Use 670-1523-1-ND
instead.
99
7
EFJOHNSON
EFJOHNSON
J2, J4, J6, J8, J14, J15, J17
CONN,THU,SMA
JACK
SMA JACK END LAUNCH,
0.080 PCB THICK. Use
J630-ND for board
thickness of .042 or J502ND for .062 or J992-ND for
.068
100
1
CONNOR WINFIELD
CWX813-10.0M
X1
OSC,SMT,4P
OSCILLATOR,SMT,4P,3.3
V,+/-25ppm,20~70C,10.000 MHz. Use
FVXO-PC73B-640-ND
instead
101
1
Texas Instruments
AFE5809
DUT1
TI Provided part
SMT,135P,BGA,1mmLS,0
22PAD (TI Provided part)
102
1
OSC,SMT,6P
VX-7040-ECE-KXX-0-640M000
OSC1
OSC,SMT,6P
VCXO,SMT,3.3V,640Mhz
5.0x7.5x1.8mm ( TI
Provided part )
54
AFE5809EVM Evaluation Module
SLOU338A – October 2012 – Revised November 2012
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
