User's Guide
SPRUIK1 – June 2018
AWR1642 Obstacle Detection Sensor
(AWR1642BOOST-ODS)
Single-Chip mmWave Sensing Solution
The AWR1642 Obstacle Detection Sensor from Texas Instruments is an easy-to-use evaluation board for
the AWR1642 mmWave sensing device, with direct connectivity to the microcontroller (MCU)
LaunchPad™ Development Kit. The Obstacle Detection Sensor contains everything required to start
developing software for on-chip C67x DSP core and low-power ARM® R4F controllers, including onboard
emulation for programming and debugging as well as onboard buttons and LEDs for quick integration of a
simple user interface.
1
2
3
4
5
6
7
Contents
Getting Started ............................................................................................................... 2
1.1
Introduction .......................................................................................................... 2
1.2
Key Features ....................................................................................................... 2
1.3
Kit Contents.......................................................................................................... 2
Hardware...................................................................................................................... 3
2.1
Block Diagram ....................................................................................................... 5
2.2
Power Connections ................................................................................................. 6
2.3
Connectors .......................................................................................................... 6
2.4
PC Connection..................................................................................................... 10
2.5
Connecting the Obstacle Detection Sensor to the LaunchPad or the MMWAVE-DEVPACK ........... 11
2.6
Antenna ............................................................................................................. 11
2.7
Jumpers, Switches, and LEDs ................................................................................... 13
Design Files and Software Tools ......................................................................................... 17
3.1
Hardware ........................................................................................................... 17
3.2
Software, Development Tools, and Example Code ........................................................... 17
Design Revision History .................................................................................................. 17
Mechanical Mounting of PCB ............................................................................................. 18
PCB Storage and Handling Recommendations ........................................................................ 18
Troubleshooting ............................................................................................................ 18
Trademarks
LaunchPad, Code Composer Studio are trademarks of Texas Instruments.
ARM is a registered trademark of ARM Limited.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
1
Getting Started
1
Getting Started
1.1
Introduction
www.ti.com
The AWR1642 Obstacle Detection Sensor from Texas Instruments is an easy-to-use evaluation board for
the AWR1642 mmWave sensing device, with direct connectivity to the microcontroller (MCU) LaunchPad
Development Kit. The Obstacle Detection Sensor contains everything required to start developing software
for on-chip C67x DSP core and low-power ARM R4F controllers, including onboard emulation for
programming and debugging as well as onboard buttons and LEDs for quick integration of a simple user
interface.
The standard 20-pin BoosterPack headers make the device compatible with a wide variety of TI MCU
LaunchPads and enables easy prototyping.
1.2
Key Features
•
•
•
•
•
•
•
•
1.3
Two 20-pin LaundPad connectors that leverages the ecosystem of the TI LaunchPad
XDS110 based JTAG emulation with a serial port for onboard QSPI flash programming
Back-channel UART through USB-to-PC for logging purposes
Onboard antenna
60-pin, high-density (HD) connector for raw analog-to-digital converter (ADC) data over LVDS and
trace-data capability
Onboard CAN-FD transceiver
One button and two LEDs for basic user interface
5-V power jack to power the board
Kit Contents
The following items are included with the AWR1642BOOST-ODS kit.
• AWR1642BOOST-ODS evaluation board
• Mounting brackets, screws, and nuts to place the printed-circuit board (PCB) vertical
• Micro USB cable to connect to PC
NOTE: A 5-V, > 2.5-A supply brick with a 2.1-mm barrel jack (center positive) is not included. TI
recommends using an external power supply that complies with applicable regional safety
standards, such as UL, CSA, VDE, CCC, PSE, and more. The length of the power cable
should be < 3 m.
2
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
2
Hardware
Figure 1 and Figure 2 show the front and rear view of the Obstacle Detection Sensor, respectively.
Figure 1. Obstacle Detection Sensor (Front)
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
3
Hardware
www.ti.com
Figure 2. Obstacle Detection Sensor (Rear)
4
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
2.1
Block Diagram
Figure 3 shows the block diagram.
4 RX and 2 TX PCBs
Power and 2 GPIO
LED indicators
UART and JTAG
LDO1
2.3 V
XDS110
1.8 V
CANFD
PC Interface
through USB
SOP
1.3 V
AWR1642
1.8 V
3.3 VIO
Current
measurement
QSPI
Flash
Optional for 3.3-V
from MCU
LaunchPadTM
JTAG and trace
1.2 V
PMIC
LVDS data and Clk
5-V input
from jack
and MCU
SPI, UART, I2C,
Rst, Nerrs,
SOPs, Loggers,
CAN, and GPIOs
BP Connector
LDO2
40-Mhz
XTAL
60-pin HD
Control signals for
external MCU interface
EN control from the
MCU
PGOOD signal to
MCU for power
sequencing
Copyright © 2017, Texas Instruments Incorporated
Figure 3. Block Diagram
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
5
Hardware
2.2
www.ti.com
Power Connections
The Obstacle Detection Sensor is powered by the 5-V power jack (5-A current limit), shown in Figure 4.
As soon as the power is provided, the NRST and 5-V LEDs should glow, indicating that the board is
powered on.
NOTE: After the 5-V power supply is provided to the Obstacle Detection Sensor, it is recommended
to press the NRST switch (SW2) one time to ensure a reliable boot-up state.
Figure 4. Power Connector
2.3
2.3.1
Connectors
20-Pin Obstacle Detection Sensor Connectors
The Obstacle Detection Sensor has the standard LaunchPad connectors (J5 and J6, shown in Figure 5)
that enable it to be directly connected to all TI MCU LaunchPads. While connecting the Obstacle
Detection Sensor to other LaunchPads, ensure the pin-1 orientation is correct by matching the 3V3 and 5V signal marking on the boards.
Figure 5. 20-Pin Obstacle Detection Sensor Connectors
6
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
Table 1 and Table 2 provide the connector-pin information.
Table 1. J5 Connector Pin
Pin Number
Description
Pin Number
Description
1
NERROUT
2
GND
3
NERRIN
4
DSS LOGGER
5
MCUCLK OUT
6
SPI_CS
7
NC
8
GPIO01
9
MSS LOGGER
10
nRESET
11
WARMRST
12
SPI_MOSI
13
BSS LOGGER
14
SPI_MISO
15
SOP2
16
HOSTINT
17
SOP1
18
GPIO02
19
SOP0
20
NC
Table 2. J6 Connector Pin
Pin Number
(1)
(2)
(3)
Description
Pin Number
Description
1
3V3
2
5V
3
NC
4
GND
5
RS232RX (Tx from AWR device)
6
ANA1 (1)
7
RS232RX (Rx into AWR device)
8
ANA2 (1)
9
SYNC_IN
10
ANA3 (1)
11
NC
12
ANA4 (1)
13
SPI_CLK
14
PGOOD (onboard VIO) (2)
15
GPIO0
16
PMIC Enable (3)
17
SCL
18
SYNC_OUT
19
SDA
20
PMIC CLK OUT
Voltage input to the GPADC available on the AWR1642.
Indicates the state of the onboard VIO supply for the AWR device coming from the onboard PMIC. A HIGH on the PGOOD
signal (3.3 V) indicates the supply is stable. Because the I/Os are not failsafe, the MCU must not drive any I/O signals to the
AWR device before this I/O supply is stable to avoid leakage current into the I/Os.
Controls the onboard PMIC enable. The MCU can use this to shut down the PMIC and AWR device during the periods it does
not use the AWR device and save power. The power up of the PMIC takes approximately 5 ms once the enable signal is made
high.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
7
Hardware
2.3.2
www.ti.com
60-Pin HD Connector
The 60-pin HD connector provides the high speed LVDS data, control signals (SPI, UART, I2C, NRST,
NERR, SOPs) and JTAG debug signals. The connector can be connected to the MMWAVE-DEVPACK
board to further get to the standard TSW1400 EVM. Figure 6 shows the HD connector, and Table 3
provides the connector information.
Figure 6. HD Connector
8
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
Table 3. J1 Connector Pin
Pin Number
(1)
Description
Pin Number
Description
1
5V
2
5V
3
5V
4
TDO
5
TDI
6
TCK
7
SPI_CS
8
TMS
9
SPI_CLK
10
HOSTINT
11
SPI_MOSI
12
SPI_MISO
13
PGOOD (onboard VIO) (1)
14
NERROUT
15
DMM_CLK
16
SYNC_IN
17
DMM_SYNC
18
GND
19
TRACE_DATA0
20
NC
21
TRACE_DATA1
22
NC
23
TRACE_DATA2
24
GND
25
TRACE_DATA3
26
LVDS_FRCLKP
27
TRACE_DATA4
28
LVDS_FRCLKM
29
TRACE_DATA5
30
GND
31
TRACE_DATA6
32
NC
33
TRACE_DATA7
34
NC
35
TRACE_DATA8
36
GND
37
TRACE_DATA9
38
NC
39
TRACE_DATA10
40
NC
41
TRACE_DATA11
42
GND
43
TRACE_DATA12
44
LVDS_CLKP
45
TRACE_DATA13
46
LVDS_CLKM
47
TRACE_DATA14
48
GND
49
TRACE_DATA15
50
LVDS_1P
51
I2C_SDA
52
LVDS_1M
53
I2C_SCL
54
GND
55
RS232RX (Rx into AWR device)
56
LVDS_0P
57
RS232TX (Tx from AWR device)
58
LVDS_0M
59
nRESET
60
GND
Indicates the state of the onboard VIO supply for the AWR device coming from the onboard PMIC. A HIGH on the PGOOD signal (3.3 V)
indicates the supply is stable. Because the I/Os are not failsafe, the MCU must not drive any I/O signals to the AWR device before this
I/O supply is stable to avoid leakage current into the I/Os.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
9
Hardware
2.3.3
www.ti.com
CAN Interface Connector
The J3 connector provides the CAN_L and CAN_H signals from the onboard CAND-FD transceiver
(TCAN1042HGVDRQ1). These signals can be directly wired to the CAN bus.
Because the digital CAN signals (Tx and Rx) are muxed with the SPI interface signals on the AWR device,
one of the two paths must be selected. In the Rev A of the board, to enable the CAN interface, R11 and
R12 resisters must be populated with 0 Ω; R4, R6, R28, and R63 resistors must be removed to disconnect
the SPI path. In the Rev B board, this is done by placing the switch S2 on the "CAN" position.
Figure 7 shows the CAN connector.
Figure 7. CAN Connector
2.4
PC Connection
The connectivity is provided through the micro USB connector over the onboard XDS110
(TM4C1294NCPDT) emulator. This connection provides the following interfaces to the PC:
• JTAG for Code Composer Studio™ (CCS) connectivity
• UART1 for flashing the onboard serial flash, downloading FW through Radar Studio, and getting
application data sent through the UART
• MSS logger UART (can be used to get MSS code logs on the PC)
When the USB is connected to the PC, the device manager should recognize the following COM ports,
shown in Figure 8:
• XDS110 Class Application/User UART – UART1 port
• XDS110 Class Auxiliary Data Port – MSS logger port
Figure 8. COM Ports
If Windows® is unable to recognize the COM ports, users must install the EMU pack available at XDS
Emulation Software Package.
10
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
2.5
Connecting the Obstacle Detection Sensor to the LaunchPad or the MMWAVE-DEVPACK
The development pack may be required with the Obstacle Detection Sensor for the following use cases:
• Connecting to Radar Studio
Radar Studio is a tool that provides capability to configure the mmWave front end from the PC. This
tool is available in the DFP package.
• Capturing high-speed LVDS data using the SW1400 FPGA platform from TI (see High Speed Data
Capture and Pattern Generation Platform).
The TSW1400 FPGA platform allows users to capture the raw ADC data over the high-speed debug
interface and post process it in the PC.
• Getting DSP trace data through the MIPI 60-pin interface
• Use the DMM interface
This Obstacle Detection Sensor can be stacked on top of the Launchpad or the MMWAVE-DEVPACK by
using the two 20-pin connectors. The connectors do not have a key to prevent the misalignment of the
pins or reverse connection. Hence, care must be taken to ensure reverse mounting does not take place.
On the AWR1642 Obstacle Detection Sensor, TI has provided 3V3 markings near pin 1, shown in
Figure 9. The same marking is provided on compatible LaunchPads (must be aligned before powering up
the boards).
Figure 9. 3V3 and 5V Marking on Obstacle Detection Sensor
For details on these use cases, see the MMWAVE-DEVPACK User's Guide.
2.6
Antenna
The Obstacle Detection Sensor includes onboard-etched antennas for the four receivers and two
transmitters that enable tracking multiple objects with their distance and angle information. This antenna
design enables estimation of distance and elevation angle that enables object detection in a twodimensional plane. Figure 10 shows the PCB antennas.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
11
Hardware
www.ti.com
Figure 10. PCB Antennas
The peak output power with the antenna gain is < 55 dBm EIRP, as required by the European regulations.
The radiation pattern in the horizontal plane (H-plane Phi = 0 degrees), elevation plane (E-plane Phi = 90
degrees), and the planes of Phi = ± 45 degrees for the four receivers are shown in Figure 11.
12
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
Figure 11. Antenna Pattern
2.7
2.7.1
Jumpers, Switches, and LEDs
Sense-on-Power (SOP) Jumpers
The AWR1642 device can be set to operate in three different modes based on the state of the SOP lines.
These lines are sensed only during boot up of the AWR device. The state of the device is detailed by
Table 4.
A closed jumpers refers to a 1, and an open jumper refers to a 0 state of the SOP signal going to the
AWR device.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
13
Hardware
www.ti.com
Table 4. SOP Jumper Information
Reference
P3
SOP 2
P2
SOP 1
P4
SOP 0
Usage
Comments
101 (SOP mode 5) = flash
programming
SOP[2:0]
001 (SOP mode 4) =
functional mode
011 (SOP mode 2) = dev
mode
Figure 12 shows the SOP jumpers.
Figure 12. SOP Jumpers
14
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Hardware
www.ti.com
2.7.2
Current Measurement
The P5 jumper enables the measurement of the current being consumed by the reference design (AWR
device, PMIC, and LDOs) at a 5-V level.
To measure the current, resistor R118 must be removed and a series ammeter can be put across the P5
pins (shown in Figure 13).
Figure 13. P5 Pins
2.7.3
Push Buttons and LEDs
Table 5 provides the switch and LED information.
Table 5. Switch and LED Information
Reference
Usage
Comments
SW2
RESET
Used to RESET the AWR1642 device.
This signal is also brought out on the 20pin connector and 60-pin HD connector so
an external processor can control the
AWR device. The onboard XDS110 can
also use this reset.
SW1
GPIO_1
When pushed, the GPIO_1 is pulled to
VCC.
DS2
5-V supply indication
This LED indicates the presence of the 5V supply.
DS4
nRESET
This LED is used to indicate the state of
nRESET pin. If this LED is glowing, the
device is out of reset. This LED will glow
only after the 5-V supply is provided.
DS1
Nerr_OUT
DS3
GPIO_1
SPRUIK1 – June 2018
Submit Documentation Feedback
Glows if there is any HW error in the AWR
device
Glows when the GPIO is logic-1
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
15
Hardware
www.ti.com
Figure 14 through Figure 19 show the location of switches and LEDs.
2.7.4
Figure 14. SW1
Figure 15. SW2
Figure 16. DS2
Figure 17. DS4
Figure 18. DS1
Figure 19. DS3
Selection Between SPI and CAN Interface
The SPI and CAN interface are muxed on the same lines on the AWR1642 device. Based on the
configuration, the user can select if the pins E14 and D13 must be connected to the 20-pin/HD connectors
to provide the SPI interface OR to the onboard CANFD PHY (U3). This selection is done by the S2 switch.
This switch is available on the board from Rev B onwards.
Figure 20. S2 Switch to Select Between SPI or CAN Interface
16
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
Design Files and Software Tools
www.ti.com
3
Design Files and Software Tools
3.1
Hardware
To view the BOM, see AWR1642EVM-ODS BOM.
To view the assembly drawings, see AWR1642EVM-ODS Assembly Files.
To view the schematics, see AWR1642EVM-ODS Schematic.
To view the design database and layout details, see AWR1642EVM-ODS Design Database.
3.2
Software, Development Tools, and Example Code
The example code and demo application for the Obstacle Detection Sensor demo can be found on the TI
resource explorer page (http://dev.ti.com/tirex/#/). Software drivers and libraries are available in the
mmwave SDK package (http://www.ti.com/tool/mmwave-sdk).
4
Design Revision History
Table 6. Design Revision History
PCB revision
Change Description
Rev B
Added switch control to move between SPI and CAN interface
Enabled by default the 5-V supply from the 60-pin HD connector.
Enabled by default the SYNC_IN signal connection to J6 connector
Serial flash part number updated to MX25V1635FZNQ
Added series resisters on I2C lines.
Removed the series diode on the NRST signal.
SPRUIK1 – June 2018
Submit Documentation Feedback
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
17
Mechanical Mounting of PCB
5
www.ti.com
Mechanical Mounting of PCB
The field of view of the radar sensor is orthogonal to the PCB. To enable easy measurements on the
sensing objects on the horizontal plane, the PCB can be mounted vertically. The L-brackets provided with
the AWR1642 Obstacle Detection Sensor kit, along with the screws and nuts help in the vertical mounting
of the Obstacle Detection Sensor. Figure 21 shows how the L-brackets can be assembled.
Figure 21. Vertical Assembly of Obstacle Detection Sensor
6
PCB Storage and Handling Recommendations
The immersion silver finish of the PCB provides a better high-frequency performance, but is also prone to
oxidation in open environments. This oxidation causes the surface around the antenna region to blacken.
To avoid oxidation, the PCB should be stored in an ESD cover and kept at a controlled room temperature
with low humidity conditions. All ESD precautions must be taken while using and handling the Obstacle
Detection Sensor.
7
Troubleshooting
Obstacle Detection Sensor Board Power-up Failure
See Section 2.2 for desired power connections. Please ensure NRST and 5-V LEDs glow brightly. When a
nonfunctional or insufficient current capacity power supply is used with the Obstacle Detection Sensor, the
Obstacle Detection Sensor LEDs will not turn on. See Section 2.7.3 for LED information.
18
AWR1642 Obstacle Detection Sensor (AWR1642BOOST-ODS) Single-Chip
mmWave Sensing Solution
Copyright © 2018, Texas Instruments Incorporated
SPRUIK1 – June 2018
Submit Documentation Feedback
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
