User's Guide
SLUUAV7B – December 2013 – Revised September 2016
bq40z50EVM Li-Ion Battery Pack Manager Evaluation
Module
This evaluation module (EVM) is a complete evaluation system for the bq40z50 or bq296000 battery
management system. The EVM includes one bq40z50 and bq296000 circuit module and a link to
Microsoft® Windows® based PC software. The circuit module includes one bq40z50 integrated circuit (IC),
one bq296000 IC, and all other onboard components necessary to monitor and predict capacity, perform
cell balancing, monitor critical parameters, protect the cells from overcharge, over-discharge, short-circuit,
and overcurrent in 1-, 2-, 3-, or 4-series cell Li-ion or Li-polymer battery packs. The circuit module
connects directly across the cells in a battery. With the EV2300 or EV2400 interface board and software,
the user can read the bq40z50 data registers, program the chipset for different pack configurations, log
cycling data for further evaluation, and evaluate the overall functionality of the solution under different
charge and discharge conditions.
1
2
3
4
5
6
7
Contents
Features ....................................................................................................................... 2
1.1
Kit Contents.......................................................................................................... 2
1.2
Ordering Information ............................................................................................... 2
1.3
Documentation ...................................................................................................... 2
1.4
bq40z50 and bq296000 Circuit Module Performance Specification Summary ............................. 2
bq40z50EVM Quick Start Guide ........................................................................................... 3
2.1
Items Needed for EVM Setup and Evaluation .................................................................. 3
2.2
Software Installation ................................................................................................ 3
2.3
EVM Connections ................................................................................................... 3
2.4
Update Firmware.................................................................................................... 5
Battery Management Studio ................................................................................................ 6
3.1
Registers Screen.................................................................................................... 6
3.2
Setting Programmable bq40z50 Options ........................................................................ 6
3.3
Calibration Screen .................................................................................................. 7
3.4
Chemistry Screen ................................................................................................... 9
3.5
Firmware Screen .................................................................................................. 10
3.6
Advanced Comm SMB Screen .................................................................................. 11
bq40z50EVM Circuit Module Schematic ................................................................................ 12
4.1
Pre-Charge ......................................................................................................... 12
4.2
LED Control ........................................................................................................ 12
4.3
Emergency Shutdown ............................................................................................ 12
4.4
Testing Fuse-Blowing Circuit .................................................................................... 12
4.5
PTC Thermistor ................................................................................................... 13
Circuit Module Physical Layouts ......................................................................................... 14
5.1
Board Layout ....................................................................................................... 14
5.2
Schematic .......................................................................................................... 17
Bill of Materials ............................................................................................................. 18
Related Documentation from Texas Instruments ...................................................................... 19
List of Figures
1
bq40z50 Circuit Module Connection to Cells and System Load or Charger ......................................... 4
2
Cell Connection Configuration ............................................................................................. 4
3
Registers Screen
............................................................................................................
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
6
1
Features
www.ti.com
4
Data Flash Screen ........................................................................................................... 7
5
Calibration Screen ........................................................................................................... 7
6
Chemistry Screen ............................................................................................................ 9
7
Firmware Screen ........................................................................................................... 10
8
Advanced Comm Screen.................................................................................................. 11
9
Fuse Trace Modifications
10
11
12
13
14
15
16
17
.................................................................................................
Top Silk Screen.............................................................................................................
Bottom Silk Screen .........................................................................................................
Top Assembly...............................................................................................................
Bottom Assembly ...........................................................................................................
Top Layer ...................................................................................................................
Internal Layer 1 .............................................................................................................
Internal Layer 2 .............................................................................................................
Bottom Layer ................................................................................................................
12
14
14
14
15
15
15
16
16
Trademarks
Impedance Track is a trademark of Texas Instruments.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
1
Features
•
•
•
1.1
Kit Contents
•
•
1.2
Complete evaluation system for the bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module and
bq296000 independent overvoltage protection IC
Populated circuit module for quick setup
Software that allows data logging for system analysis
bq40z50 and bq296000 circuit module
Cable to connect the EVM to an EV2300 or EV2400 communications interface adapter
Ordering Information
For complete ordering information, see the product page at www.ti.com.
Table 1. Ordering Information
1.3
EVM PART NUMBER
CHEMISTRY
CONFIGURATION
CAPACITY
bq40z50EVM-561
Li-ion
1-, 2-, 3-, or 4-cell
Any
Documentation
See the device data sheets for bq40z50 and bq296000 and technical reference manuals (TRMs) on
www.ti.com for information on device firmware and hardware.
1.4
bq40z50 and bq296000 Circuit Module Performance Specification Summary
This section summarizes the performance specifications of the bq40z50 and bq296000 EVM.
Table 2. Performance Specification Summary
Specification
2
Minimum
Typical
Maximum
Input voltage Pack+ to Pack–
3
15
26
V
Charge and discharge current
0
2
7
A
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Units
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
bq40z50EVM Quick Start Guide
www.ti.com
2
bq40z50EVM Quick Start Guide
This section provides the step-by-step procedures required to use a new EVM and configure it for
operation in a laboratory environment.
2.1
Items Needed for EVM Setup and Evaluation
•
•
•
•
•
•
•
•
2.2
bq40z50 or bq296000 circuit module
EV2300 or EV2400 communications interface adapter
Cable to connect the EVM to an EV2300 or EV2400 communications interface adapter
USB cable to connect the communications interface adapter to the computer
Computer setup with Windows XP, or higher, operating system
Access to the Internet to download the Battery Management Studio software setup program
One-to-four battery cells or 1-kΩ resistors to configure a cell simulator
A DC power supply that can supply 16.8 V and 2 A (constant current and constant voltage capability is
desirable)
Software Installation
Find the latest software version in the bq40z50 tool folder on www.ti.com. Use the following steps to install
the bq40z50 Battery Management Studio software:
1. Download and run the Battery Management Studio setup program from the Development Tools section
of the bq40z50EVM product folder on www.ti.com. See Section 3 for detailed information on using the
tools in the Battery Management Studio.
2. If the communications interface adapter was not previously installed, after the Battery Management
Studio installation, a TI USB driver installer pops up. Click “Yes” for the agreement message and follow
its instructions. Two drivers are associated with the EV2300 and an additional file may be required for
the EV2400. Follow the instructions to install both. Do not reboot the computer, even if asked to do so.
3. Plug the communications interface adapter into a USB port using the USB cable. The Windows system
may show a prompt that new hardware has been found. When asked, "Can Windows connect to
Windows Update to search for software?", select "No, not this time", and click "Next". In the next dialog
window, it indicates "This wizard helps you install software for: TI USB Firmware Updater". Select
"Install the software automatically (Recommended)" and click "Next". It is common for the next screen
to be the Confirm File Replace screen. Click "No" to continue. If this screen does not appear, then go
to the next step. After Windows indicates that the installation was finished, a similar dialog window
pops up to install the second driver. Proceed with the same installation preference as the first one. The
second driver is TI USB bq80xx Driver.
2.3
EVM Connections
This section covers the hardware connections for the EVM. See Figure 1.
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
3
bq40z50EVM Quick Start Guide
www.ti.com
EV2300
PACK–
SYS PRES
PACK+
SMBC
VSS
–
+
SMBD
Load/Charger
Figure 1. bq40z50 Circuit Module Connection to Cells and System Load or Charger
•
Direct connection to the cells: 1N (BAT–), 1P, 2P, 3P, 4P (BAT+)
Attach the cells to the J1 and J5 terminal block. A specific cell connection sequence is not required;
although, it is good practice to start with lowest cell in the stack (cell 1), then attach cells 2 through 4 in
sequence. The U1 and U2 devices should not be damaged by other cell connection sequences, but
there is a possibility that the bq296000 could blow the fuse. Attaching cells starting with cell 1 should
eliminate this risk. A short should be placed across unused voltage sense inputs. See Figure 2.
Number
of Cells
1
2
3
4
1N
‐cell1+
‐cell1+
‐cell1+
‐cell1+
J1 and J5 Terminal Block Connections
1P
2P
3P
short
short
‐cell2+
short
‐cell2+
‐cell3+
‐cell2+
‐cell3+
4P
short
short
short
‐cell4+
Figure 2. Cell Connection Configuration
•
•
•
4
A resistor cell simulator can be used instead of battery cells. Connect a resistor between each of the
contacts on the J1 or J5 connector. For example, from 1N to 1P, from 1P to 2P, and so forth, until the
desired number of cells has been achieved. A power supply can provide power to the cell simulator.
Set the power supply to the desired cell voltage × the number of cells and attach the ground wire to 1N
and the positive wire to 4P. For example, for a 3S configuration with a 3.6-V cell voltage, set the power
supply to 3 × 3.6 = 10.8 V.
Serial communications port (SMBC, SMBD)
Attach the communications interface adapter cable to J2 and to the SMB port on the EV2300.
System load and charger connections across PACK+ and PACK–
Attach the load or power supply to the J3 or J4 terminal block. The positive load or power supply wire
should be connected to at least one of the first two terminal block positions labeled PACK+. The
ground wire for the load or power supply should be connected to the last terminal block positions
labeled PACK–.
System-present pin (SYS PRES)
To start charge or discharge test, connect the SYS PRES position on the J3 terminal block to PACK–.
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
bq40z50EVM Quick Start Guide
www.ti.com
•
•
2.4
The SYS PRES can be left open if the non-removable (NR) bit is set to 1 in the Pack Configuration A
register. To test sleep mode, disconnect the SYS PRES pin.
Wake-up the device up from shutdown (WAKE)
Press the Wake pushbutton switch to temporarily connect Bat+ to Pack+. This applies voltage to the
PACK pin on the bq40z50 to power-up the regulators and start the initialization sequence.
Parameter setup
The default data flash settings configure the device for 3-series Li-Ion cells. The user should change
the | Data Flash | Settings | DA Configuration register to set up the number of series cells to match the
physical pack configuration. This provides basic functionality to the setup. Other data flash parameters
should also be updated to fine tune the gauge to the pack. See the bq40z50 TRM for help with setting
the parameters.
Update Firmware
Find the latest firmware version in the appropriate bq40z50 folder on www.ti.com. Use the following steps
to install the bq40z50 Battery Management Studio software:
1. Run Battery Management Studio from the Start | Programs | Texas Instruments | Battery
Management Studio menu sequence, or the Battery Management Studio shortcut.
2. Follow the directions in Section 3.5, select the firmware .srec file downloaded from www.ti.com, and
click the Program button.
3. Once programming is finished, the EVM is ready to use with the latest firmware.
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
5
Battery Management Studio
www.ti.com
3
Battery Management Studio
3.1
Registers Screen
Run Battery Management Studio from the Start | Programs | Texas Instruments | Battery Management
Studio menu sequence, or the Battery Management Studio shortcut. The Registers screen (see Figure 3)
appears. The Registers section contains parameters used to monitor gauging. The Bit Registers section
provides bit level picture of status and fault registers. A green flag indicates that the bit is 0 (low state) and
a red flag indicates that the bit is 1 (high state). Data begins to appear once the Refresh (single-time scan)
button is selected, or it scans continuously if the Scan button is selected.
Figure 3. Registers Screen
The continuous scanning period can be set via the | Window | Preferences | SBS | Scan Interval | menu
selections.
The Battery Management Studio program provides a logging function which logs the values that are
selected by the Log check boxes located beside each parameter in the Register section. To enable this
function, select the Log button; this causes the Scan button to be selected. When logging is stopped, the
Scan button is still selected and has to be manually deselected.
3.2
Setting Programmable bq40z50 Options
The bq40z50 data flash comes configured per the default settings detailed in the bq40z50 TRM. Ensure
that the settings are correctly changed to match the pack and application for the solution being evaluated.
NOTE: The correct setting of these options is essential to get the best performance. The settings
can be configured using the Data Flash screen (see Figure 4).
6
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Battery Management Studio
www.ti.com
Figure 4. Data Flash Screen
3.3
Calibration Screen
The voltages, temperatures, and currents should be calibrated to provide good gauging performance.
Press the Calibration button to select the Advanced Calibration window. See Figure 5.
Figure 5. Calibration Screen
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
7
Battery Management Studio
3.3.1
•
•
•
•
•
3.3.2
3.3.3
www.ti.com
Voltage Calibration
Measure the voltage from Cell 1 to 1N and enter this value in the Applied Cell 1 Voltage field and
select the Calibrate Voltage box.
Measure the voltage from Bat+ to Bat– and enter this value in the Applied Battery Voltage field and
select the Calibrate Battery Voltage box.
Measure the voltage from Pack+ to Pack– and enter this value in the Applied Pack Voltage field and
select the Calibrate Pack Voltage box. If the voltage is not present, then turn the charge and discharge
FETs on by entering a 0x0022 command in the Manufacturer Access register on the Register screen.
Press the Calibrate Gas Gauge button to calibrate the voltage measurement system.
Deselect the Calibrate Voltage boxes after voltage calibration has completed.
Temperature Calibration
• Enter the room temperature in each of the Applied Temperature fields and select the Calibrate box for
each thermistor to be calibrated. The temperature values must be entered in degrees Celsius.
• Press the Calibrate Gas Gauge button to calibrate the temperature measurement system.
• Deselect the Calibrate boxes after temperature calibration has completed.
Current Calibration
The Board Offset calibration option is not offered in Battery Management Studio, because it is not required
when using the bq40z50EVM. The Board Offset calibration option is available in bqProduction.
• Connect and measure a 2-A current source from 1N (–) and Pack– (+) to calibrate without using the
FETs. (TI does not recommend calibration using the FETs.)
• Enter –2000 in the Applied Current field and select the Calibrate Current box.
• Press the Calibrate Gas Gauge button to calibrate.
• Deselect the Calibrate Current box after current calibration has completed.
NOTE: Current can also be calibrated using the FETs. Measure the current in the discharge path
and enter this value in the Applied Current field.
8
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Battery Management Studio
www.ti.com
3.4
Chemistry Screen
The chemistry file contains parameters that the simulations use to model the cell and its operating profile.
It is critical to program a Chemistry ID that matches the cell into the device. Some of these parameters
can be viewed in the Data Flash section of the Battery Management Studio.
Press the Chemistry button to select the Chemistry window.
Figure 6. Chemistry Screen
•
•
•
The table can be sorted by clicking the desired column. for example: Click the Chemistry ID column
header.
Select the ChemID that matches your cell from the table (see Figure 6).
Press the Update Chemistry in the Data Flash button to update the chemistry in the device.
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
9
Battery Management Studio
3.5
www.ti.com
Firmware Screen
Press the Firmware button to select the Firmware Update window. This window allows the user to export
and import the device firmware.
Figure 7. Firmware Screen
3.5.1
Programming the Flash Memory
The upper section of the Firmware screen is used to initialize the device by loading the default .srec into
the flash memory (see Figure 7).
• Search for the .srec file using the Browse button.
• Select the Execute after programming box to automatically return the device to Normal mode after
programming has completed.
• Press the Program button and wait for the download to complete.
3.5.2
Exporting the Flash Memory
The lower section of the Firmware screen is used to export all of the flash memory from the device (see
Figure 7).
• Press the Browse button and enter an .srec filename.
• Press the Read Srec to save the flash memory contents to the file. Wait for the download to complete.
10
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Battery Management Studio
www.ti.com
3.6
Advanced Comm SMB Screen
Press the Advanced Comm SMB button to select the Advanced SMB Comm window. This tool provides
access to parameters using SMB and Manufacturing Access commands. See Figure 8.
Figure 8. Advanced Comm Screen
Examples:
Reading an SMB Command.
• Read SBData Voltage (0x09)
– SMBus Read Word. Command = 0x09
– Word = 0x3A7B, which is hexadecimal for 14971 mV
Sending a MAC Gauging() to enable IT via ManufacturerAccess().
• With Impedance Track™ disabled, send Gauging() (0x0021) to ManufacturerAccess().
– SMBus Write Word. Command = 0x00. Data = 00 21
Reading Chemical ID() (0x0006) via ManufacturerAccess()
• Send Chemical ID() to ManufacturerAccess()
– SMBus Write Word. Command = 0x00. Data sent = 00 06
• Read the result from ManufacturerData()
– SMBus Read Block. Command = 0x23. Data read = 00 01
– That is 0x0100, chem ID 100
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
11
bq40z50EVM Circuit Module Schematic
4
www.ti.com
bq40z50EVM Circuit Module Schematic
This section contains information on modifying the EVM and using various features on the reference
design.
4.1
Pre-Charge
The EVM provides a power resistor and FET to support a reduced current pre-charge path to charge the
pack when cell voltages are below the pre-charge voltage threshold. This reduces heating that could lead
to cell damage or reduced operating lifetime. The resistor (R1) is set up to limit the current to less than 40
mA for a 4S configuration. The user can change R1 to setup the pre-charge current to a different value.
4.2
LED Control
The EVM is configured to support five LEDs to provide state-of-charge information for the cells. The LED
interface is enabled by entering a 0x0027 command in the Manufacturing Access register on the Registers
screen. Press the LED DISPLAY button to illuminate the LEDs for approximately 5 seconds.
4.3
Emergency Shutdown
The Emergency Shutdown function allows the user to disable the charge and discharge FETs with an
external GPIO pin. The EMSHUT and NR bits must be set high in the DA Configuration register to enable
this feature. Press the SHUTDOWN pushbutton switch for one second to disable these FETs, and press it
again for one second to enable them.
NOTE: Remember to remove the SYS PRES-to-PACK– short, if present.
4.4
Testing Fuse-Blowing Circuit
To prevent the loss of board functionality during the fuse-blowing test, the actual chemical fuse is not
provided on the EVM. FET Q5 drives the FUSE test point low if a fuse-blow condition occurs. FUSE is
attached to an open drain FET, so a pull-up resistor is required to check whether the FUSE pulls low. A
FUSEPIN test point is attached to the gate of Q5; so, monitoring FUSEPIN can be used to test this
condition without adding a pull-up resistor. Fuse placement on the application board is shown in the
bq40z50 data sheet. A chemical fuse can also be soldered to the EVM for in-system testing. A copper
bridge is included on the PCB to bypass the chemical fuse, so it has to be cut to allow the fuse to open
the power path. The cut is illustrated in yellow on Figure 9 with arrows pointing to the location.
Cut Copper
here.
Top Layer
Bottom Layer
Figure 9. Fuse Trace Modifications
12
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
bq40z50EVM Circuit Module Schematic
www.ti.com
4.5
PTC Thermistor
The PTC interface is designed to work with a specific PTC thermistor. The thermistor must have a 10-kΩ
typical resistance over the normal operating temperature range and the resistance must be greater than
1.2 MΩ at the PTC trip temperature. The muRata PRF18BA103QB1RB thermistor will work with this
device.
The EVM has a 10-kΩ resistor installed on the PTC footprint.
The PTC function can be disabled by connecting PTC and PTCEN to VSS.
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
13
Circuit Module Physical Layouts
5
www.ti.com
Circuit Module Physical Layouts
This section contains the printed-circuit board (PCB) layout, assembly drawings, and schematic for the
bq40z50 and bq296000 circuit modules.
5.1
Board Layout
This section shows the dimensions, PCB layers (see through Figure 17), and assembly drawing for the
bq40z50 modules.
Figure 10. Top Silk Screen
Figure 11. Bottom Silk Screen
Figure 12. Top Assembly
14
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Circuit Module Physical Layouts
www.ti.com
Figure 13. Bottom Assembly
4250 mil
1250 mil
Figure 14. Top Layer
4250 mil
1250 mil
Figure 15. Internal Layer 1
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
15
Circuit Module Physical Layouts
www.ti.com
4250 mil
1250 mil
Figure 16. Internal Layer 2
4250 mil
1250 mil
Figure 17. Bottom Layer
16
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Circuit Module Physical Layouts
www.ti.com
5.2
Schematic
C1
C2
0.1 µF
0.1 µF
4P
R1
3
2
Q1
FDN358P
1
300
F1
PACK+
2
3
2
1
R2
10M
R3
Q3
Si7114DN
Q2
Si7114DN
10M
4
SFDxxxx
4
3
5
1
2
3
2
DNP
5
FUSE
1
R5
Q4
2N7002K
1
3
1
Wake
1
R4
10M
4P
Q5
Si1414DH
7
VSS
PWPD
6
9
R8
R9
R10
5.1K
100
5.1K
DSG
R6
C3
51K
R33
5.1
R12
1
REG
CHGND
R7
5.1K
10K
0.1 µF
CHG
TP11
1
R14
3
1
C4
0.1 µF
8
4
R13
1K
OUT
1
U2
1 VDD
2
V4
3
V3
4
V2
5
V1
S1
3
FUSEPIN
1
6
100
PACK+
10K
5
2
1
R11
R32
10K
P
0.1 µF
C6
R15
0.1 µF
C9
0.1 µF
R18
R17
5.1K
5.1K
RT1
0.1 µF
C8
0.1 µF
10K
BAT
GND
C10
0.1 µF
2
BAT
VCC
25
BAT
J4
1
2
FUSE
26
28
29
30
31
27
PACK
DSG
NC
PWPD
0.1 µF
CHG
C11
PCHG
1
33
1
BAT
GND
1K
R16
32
1K
C12
AGND
C7
0.47µF
BAT
4P
C5
1
1K
BQ296100DSGT
1
2
3
RT4
RT5
10K
10K
10K
C19
DNP
DNP
100
GND
GND
1
1
2
GND SIDE
2
GND SIDE
1
1
SMBD
SMBC
1
100
1
SHUTDOWN
0.1 µF
C20
R31 DNP
GND
DNP
100
2001
2DNP
S3
GND
C21
DNP
DNP
4
SMBC
J6
C18
R30
100
R27
3
SMBD
2
SMBC
1
VSS
J2
CHGND
R28
R29
200
1K
D2
D3
D4
CHGND
GND
GND SIDE
RT3
10K
200
R26
MM3Z5V6C
RT2
R25
SMBD
1
GND
R24
S2
LED DISPLAY GND
TP12
1
1
1
ND
SM BC
1
TS4
NC
15
14
13
SRN
1
SRP
GND
GND
1
NT1
Net-Tie
CHGND
LED2
SMBD
1
1
12
9
1
TS3
TP3
100
TS2
100
GND
R23
VSS
1
2
SMBC
19
D9
LED5
J3
D8
D7
LED1
1
100 R22
3
LEDCNTLA
2
R21
TS1
100
21
20
SMBD 18
DISP 17
11
2
0.1 µF
3
D6
LED4
22
LEDCNTLB
7 NC
8 SRP
C17
10
R20
23
BTP_INT
16 PRESorSHUTDN
0.1 µF
1
PTC
D5
LED3
GND SIDE
2
C16
PTCEN
24
LEDCNTLC
BQ40Z50RSM-R1
5 VC1
6 SRN
C15
0.1 µF
1
U1
3 VC3
4 VC2
C14
0.1 µF
2.2 µF
1 PBI
2 VC4
MM3Z5V6C
C13
MM3Z5V6C
D1
BAT54HT1G
CHGND
GND
R19
GND
0.001
1
IC ground should be connected to the 1N cell tab.
2
Place RT1 close to Q2 and Q3.
3
Replace D1 and R9 with a 10 ohm resistor for Single cell applications
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
Copyright © 2013–2016, Texas Instruments Incorporated
17
Bill of Materials
6
Bill of Materials
COUNT
18
www.ti.com
RefDes
Value
Description
Size
Part Number
MFR
16
C1-6, C8-12, C14-18
0.1 µF
Capacitor, Ceramic Chip, 50 V, X7R,
20%
0603
C0603C104M5RACTU
Kemet
1
C7
0.47 µF
Capacitor, Ceramic, 0.47 µF, 10 V, X5R,
10%
0603
C0603C474K8PACTU
Kemet
1
C13
2.2 µF
Capacitor, Ceramic, 25 V, X7R, 20%
0805
C2012X7R1E225M085AB
0
C19-21
DNP
Capacitor, Ceramic, 50 V, X7R, 20%
0603
C0603C104M5RACTU
1
D1
BAT54HT1G
Diode, Schottky, 200-mA, 30-V
SOD323
BAT54HT1G
On Semi
3
D2-4
MM3Z5V6C
Diode, Zener, 5.6V, 200mW
SOD323
MM3Z5V6C
Fairchild
5
D5-9
SML-X23GC
LED 2x3mm 565nm GRN WTR CLR
SMD
1206
SML-X23GC
Lumex
0
F1
DNP
Fuse, Slo-Blo Ceramic, xxA, yyyV
1
R1
300
Resistor, Chip, 1W, 5%
2512
CRCW2512300RJNEG
Vishay-Dale
3
R2-3, R5
10M
Resistor, Chip, 1/10-W, 5%
0603
CRCW060310M0JNEA
Vishay-Dale
3
R4, R12, R32
10K
Resistor, Chip, 1/10-W, 5%
0603
CRCW060310K0JNEA
Vishay-Dale
1
R6
51K
Resistor, Chip, 1/16-W, 5%
0603
CRCW060351K0JNEA
Vishay-Dale
5
R7-8, R10, R16-17
5.1K
Resistor, Chip, 1/10-W, 5%
0603
CRCW06035K10JNEA
Vishay-Dale
10
R9, R11, R20-23,
R25, R27, R30-31
100
Resistor, Chip, 1/10-W, 5%
0603
CRCW0603100RJNEAHP
Vishay-Dale
5
R13-15 R18 R29
Vishay-Dale
1
R19
3
R24, R26, R28
1
R33
2
J1, J4
1
J2
2
J3, J5
0
SFDxxx
SFDxxxx
TDK
Kemet
Sony
1K
Resistor, Chip, 1/10-W, 5%
0603
CRCW06031K00JNEA
0.001 50ppm
Resistor, Chip, 1 watt, ± 1%
1206
CSR1206-0R001F1
200
Resistor, Chip, 1/16-W, 5%
0603
CRCW0603200RJNEA
Vishay-Dale
5.1
Resistor, 5.1, 0.063 W, 5%, 0402
0402
CRCW04025R10JNED
Vishay-Dale
ED555/2DS
Terminal Block, 2-pin, 6-A, 3.5mm
0.27 x 0.25
inch
ED555/2DS
OST
22-05-3041
Header, Friction Lock Ass'y, 4-pin Right
Angle,
0.400 x
0.500 inch
22-05-3041
Molex
ED555/3DS
Terminal Block, 3-pin, 6-A, 3.5mm
0.41 x 0.25
inch
ED555/3DS
OST
J6
Header, TH, 100mil spacing, 2x1, 230 mil
above insulator
0.100 inch x PEC02SAAN
2
1
LBL1
Thermal Transfer Printable Labels, 1.250
W x 0.250 H inch - 10,000 per roll
1
RT1
10K
Thermistor, NTC, 5 Ω , 1-A
4
RT2-5
10K
Thermistor, NTC, 3-A
0.095 X
0.150 inch
103AT-2
3
S1, S2, S3
Switch, Push button, Momentary, 1P1T,
50-mA, 12-V
0.200 x
0.200 inch
EVQ-PLHA15
Panasonic
1
TP3
Test Point, Black, Thru Hole Color Keyed
0.100 x
0.100 inch
5001
Keystone
1
Q1
FDN358P
Fairchild
2
Q2-3
1
1
EVQ-PLHA15
5001
FDN358P
PCB Label
1.250 W x
0.250 H
inch
1206
MOSFET, Pch, -30V, -1.5A, 125 mΩ
SOT23
THT-13-457-10
CRCW120610K0JNEA
Riedon
Sullins
Brady
Vishay
Semitec
Si7114DN-T1-E3
MOSFET Nch 30V, 11.7A, 7.5 mΩ
PWRPAK
1212
Si7114DN-T1-E3
Vishay
Q4
2N7002K-T1-E3
MOSFET, Nch, 60V, 300 mA, 2-Ω
SOT23
2N7002K-T1-E3
Vishay
Q5
Si1414DH-T1-GE3
MOSFET, Nch, 30V, 4A, 46 mΩ
SC-70
Si1414DH-T1-GE3
Vishay
1
U1
BQ40Z50RSMR(T)R1
IC, 2- to 4-Series Li-Ion Battery Pack
Manager
1
U2
IC, Overvoltage Protection for 2-Series,
3-Series, and 4-Series Cell Li-Ion
Batteries with Regulated Output Supply,
DSG0008A
1
W1
Cable assembly, 4 pin
1
IPCB
Printed Circuit Board
bq40z50EVM Li-Ion Battery Pack Manager Evaluation Module
QFN
DSG0008A
BQ40Z50RSMR(T)-R1
TI
BQ296103DSGT
TI
N/A
CBL002
TI
4.25 in x
1.25 in
PWR561
Any
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Related Documentation from Texas Instruments
www.ti.com
7
Related Documentation from Texas Instruments
•
•
•
bq40z50, 1-Series, 2-Series, 3-Series, and 4-Series Li-Ion Battery Pack Manager data sheet,
SLUSBS8
bq40z50 Technical Reference Manual, SLUUA43
bq296000, BQ2960XY/BQ2961XY Overvoltage Protection for 2-Series, 3-Series, and 4-Series Cell LiIon Batteries with Regulated Output Supply, SLUSBU5
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from A Revision (July, 2015) to B Revision .................................................................................................... Page
•
Added Update Firmware section. ....................................................................................................... 5
SLUUAV7B – December 2013 – Revised September 2016
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Revision History
19
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
