Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
CD74HC125-Q1 Automotive Quadruple Buffers with 3-State Outputs
1 Features
3 Description
•
This device contains four independent buffers with 3state outputs. Each gate performs the Boolean
function Y = A in positive logic.
1
•
•
•
•
•
AEC-Q100 Qualified for automotive applications:
– Device temperature grade 1:
–40°C to +125°C, TA
Buffered inputs
Positive and negative input clamp diodes
Wide operating voltage range: 2 V to 6 V
Supports fanout up to 10 LSTTL loads
Significant power reduction compared to LSTTL
logic ICs
Device Information(1)
PART NUMBER
CD74HC125QM96G4
Q1
PACKAGE
SOIC (14)
CD74HC125QPWRQ1 TSSOP (14)
BODY SIZE (NOM)
8.70 mm × 3.90 mm
5.00 mm × 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
•
Enable digital signals
Functional pinout of the CD74HC125-Q1
1
14
VCC
2
13
4OE
3
4
12
11
4A
2A
5
10
3OE
2Y
6
7
9
8
1OE
1A
1Y
2OE
GND
4Y
3A
3Y
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
3
4
4
4
5
5
6
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Operating Characteristics..........................................
Typical Characteristics ..............................................
Parameter Measurement Information .................. 6
Detailed Description .............................................. 8
8.1 Overview ................................................................... 8
8.2 Functional Block Diagram ......................................... 8
8.3 Feature Description................................................... 8
8.4 Device Functional Modes.......................................... 9
9
Application and Implementation ........................ 10
9.1 Application Information............................................ 10
9.2 Typical Application .................................................. 10
10 Power Supply Recommendations ..................... 12
11 Layout................................................................... 12
11.1 Layout Guidelines ................................................. 12
11.2 Layout Example .................................................... 12
12 Device and Documentation Support ................. 13
12.1
12.2
12.3
12.4
12.5
12.6
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
13
13
13
13
13
13
13 Mechanical, Packaging, and Orderable
Information ........................................................... 13
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (September 2008) to Revision B
Page
•
Updated to new data sheet standards.................................................................................................................................... 1
•
Changed RθJA for PW package from 113 °C/W to 151.7 °C/W .............................................................................................. 4
•
Changed RθJA for D package from 86 °C/W to 133.6 °C/W ................................................................................................... 4
2
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
5 Pin Configuration and Functions
D or PW Package
14-Pin SOIC or TSSOP
Top View
1
14
VCC
2
13
4OE
3
4
12
11
4A
2A
5
10
3OE
2Y
6
7
9
8
1OE
1A
1Y
2OE
GND
4Y
3A
3Y
Pin Functions
PIN
NAME
I/O
NO.
DESCRIPTION
1OE
1
Input
Channel 1, Output Enable, Active Low
1A
2
Input
Channel 1, Input A
1Y
3
Output
2OE
4
Input
Channel 2, Output Enable, Active Low
2A
5
Input
Channel 2, Input A
2Y
6
Output
GND
7
—
3Y
8
Output
3A
9
Input
Channel 3, Input A
3OE
10
Input
Channel 3, Output Enable, Active Low
4Y
11
Output
4A
12
Input
Channel 4, Input A
4OE
13
Input
Channel 4, Output Enable, Active Low
VCC
14
—
Channel 1, Output Y
Channel 2, Output Y
Ground
Channel 3, Output Y
Channel 4, Output Y
Positive Supply
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
–0.5
7
UNIT
VCC
Supply voltage
IIK
Input clamp current (2)
VI < –0.5 V or VI > VCC +
0.5 V
±20
mA
IOK
Output clamp current (2)
VO < –0.5 V or VO > VCC +
0.5 V
±20
mA
IO
Continuous output current
VO > –0.5 V or VO < VCC
+ 0.5 V
±25
mA
±70
mA
150
°C
150
°C
Continuous current through VCC or GND
TJ
Junction temperature
Tstg
Storage temperature
(1)
(2)
(3)
(3)
–65
V
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
Guaranteed by design.
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
3
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
6.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic discharge
Human body model (HBM), per AEC Q100-002 (1)
HBM ESD Classification Level 2
±2000
Charged device model (CDM), per AEC Q100011 CDM ESD Classification Level C6
±1000
UNIT
V
AEC Q100-002 indicate that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VCC
MIN
NOM
MAX
2
5
6
Supply voltage
VCC = 2 V
VIH
High-level input voltage
VCC = 4.5 V
3.15
V
4.2
VCC = 2 V
Low-level input voltage
V
1.5
VCC = 6 V
VIL
UNIT
0.5
VCC = 4.5 V
1.35
VCC = 6 V
V
1.8
VI
Input voltage
0
VCC
V
VO
Output voltage
0
VCC
V
Δt/Δv
Input transition rise and fall rate
VCC = 2 V
TA
1000
VCC = 4.5 V
500
VCC = 6 V
400
Operating free-air temperature
–40
125
ns
°C
6.4 Thermal Information
CD74HC125-Q1
THERMAL METRIC
PW (TSSOP)
D (SOIC)
14 PINS
14 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
151.7
133.6
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
79.4
89.0
°C/W
RθJB
Junction-to-board thermal resistance
94.7
89.5
°C/W
ΨJT
Junction-to-top characterization parameter
25.2
45.5
°C/W
ΨJB
Junction-to-board characterization parameter
94.1
89.1
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
°C/W
4
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
6.5 Electrical Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
Operating free-air temperature (TA)
PARAMETER
TEST CONDITIONS
VCC
25°C
MIN
IOH = -20 µA
VOH
High-level output
voltage
VI = VIH or VIL
Low-level output
voltage
-40°C to 125°C
MAX
MIN
2V
1.9
1.9
4.5 V
4.4
4.4
5.9
5.9
IOH = -6 mA
6V
4.5 V
3.98
3.7
IOH = -7.8 mA
6V
5.48
5.2
IOL = 20 µA
VOL
TYP
VI = VIH or VIL IOL = 20 µA
TYP
UNIT
MAX
V
2V
0.1
0.1
4.5 V
0.1
0.1
6V
0.1
0.1
IOL = 6 mA
4.5 V
0.26
0.4
IOL = 7.8 mA
6V
0.26
0.4
V
II
Input leakage
current
VI = VCC or GND
6V
±0.1
±1
µA
ICC
Supply current
VI = VCC or
GND
6V
8
160
µA
IOZ
Off-state output
current
VI = VIL or VIH
6V
±0.5
±10
µA
Ci
Input
capacitance
10
10
pF
CO
Output
capacitance
20
20
pF
IO = 0 mA
2 V to 6 V
3-state
6.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
Operating free-air temperature (TA)
PARAMETER
FROM
TO
CONDITIONS
VCC
25°C
MIN
TYP
2V
tpd
Propagation delay
A
Y
CL = 50 pF
CL = 15 pF
Enable time
OE
Y
CL = 50 pF
CL = 15 pF
Disable time
OE
Y
CL = 50 pF
CL = 15 pF
tt
Transition-time
Y
CL = 50 pF
MIN
TYP
150
20
30
6V
17
26
125
190
4.5 V
25
38
6V
21
32
125
190
4.5 V
25
38
6V
21
32
2V
60
90
4.5 V
12
18
6V
10
15
5V
5V
5V
Product Folder Links: CD74HC125-Q1
ns
8
ns
10
ns
10
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
UNIT
MAX
4.5 V
2V
tdis
MAX
100
2V
ten
–40°C to 125°C
ns
5
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
6.7 Operating Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
PARAMETER
Cpd
TEST CONDITIONS
Power dissipation capacitance
per gate
No load
VCC
MIN
TYP
5V
MAX UNIT
29
pF
6.8 Typical Characteristics
TA = 25°C
7
0.15
6
VOH Output High Voltage (V)
VOL Output Low Voltage (V)
0.135
0.12
0.105
0.09
0.075
0.06
0.045
0.03
2V
4.5 V
6V
0.015
5
4
3
2
2V
4.5 V
6V
1
0
0
0
0.0009
0.0018 0.0027 0.0036 0.0045
IOL Output Low Current (mA)
0
0.0054
0.001
0.002
0.003
0.004
IOH Output High Current (mA)
D001
Figure 1. Output voltage versus output current in low state
0.005
0.006
D002
Figure 2. Output voltage versus output current in high state
7 Parameter Measurement Information
•
•
Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators
having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tt < 6 ns.
The outputs are measured one at a time, with one input transition per measurement.
VCC
Test
Point
90%
10%
10%
S1
tr(1)
RL
From Output
Under Test
VCC
90%
Input
CL(1)
90%
S2
0V
tf(1)
VOH
90%
Output
10%
CL= 50 pF and includes probe and jig capacitance.
Figure 3. Load Circuit
6
Submit Documentation Feedback
10%
tr(1)
tf(1)
VOL
Figure 4. Voltage Waveforms
Transition Times
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
Parameter Measurement Information (continued)
VCC
Output
Control
50%
50%
0V
tPZL
(3)
tPLZ
(4)
§ 9CC
Output
Waveform 1
S1 at VLOAD(1)
50%
10%
VOL
tPZH(3)
Output
Waveform 2
S1 at GND(2)
tPHZ(4)
90%
VOH
50%
§0V
The maximum between tPLH and tPHL is used for tpd.
Figure 5. Voltage Waveforms
Propagation Delays
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
7
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
8 Detailed Description
8.1 Overview
This device contains four independent buffers with 3-state outputs. Each gate performs the Boolean function Y =
A in positive logic.
8.2 Functional Block Diagram
xOE
xA
xY
8.3 Feature Description
8.3.1 Balanced CMOS 3-State Outputs
A balanced output allows the device to sink and source similar currents. The drive capability of this device may
create fast edges into light loads so routing and load conditions should be considered to prevent ringing.
Additionally, the outputs of this device are capable of driving larger currents than the device can sustain without
being damaged. It is important for the output power of the device to be limited to avoid damage due to overcurrent. The electrical and thermal limits defined in the Absolute Maximum Ratings must be followed at all times.
The CD74HC125-Q1 can drive a load with a total capacitance less than or equal to 50 pF connected to a highimpedance CMOS input while still meeting all of the datasheet specifications. Larger capacitive loads can be
applied, however it is not recommended to exceed 70 pF. If larger capacitive loads are required, it is
recommended to add a series resistor between the output and the capacitor to limit output current to the values
given in the Absolute Maximum Ratings.
3-State outputs can be placed into a high-impedance state. In this state, the output will neither source nor sink
current, and leakage current is defined by the IOZ specification in the Electrical Characteristics. A pull-up or pulldown resistor can be used to ensure that the output remains HIGH or LOW, respectively, during the highimpedance state.
8.3.2 Standard CMOS Inputs
Standard CMOS inputs are high impedance and are typically modeled as a resistor from the input to ground in
parallel with the input capacitance given in the Electrical Characteristics. The worst case resistance is calculated
with the maximum input voltage, given in the Absolute Maximum Ratings, and the maximum input leakage
current, given in the Electrical Characteristics, using ohm's law (R = V ÷ I).
Signals applied to the inputs need to have fast edge rates, as defined by Δt/Δv in the Recommended Operating
Conditions to avoid excessive current consumption and oscillations. If a slow or noisy input signal is required, a
device with a Schmitt-trigger input should be used to condition the input signal prior to the standard CMOS input.
8
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
Feature Description (continued)
8.3.3 Clamp Diode Structure
The inputs and outputs to this device have both positive and negative clamping diodes as depicted in Figure 6.
CAUTION
Voltages beyond the values specified in the Absolute Maximum Ratings table can
cause damage to the device. The recommended input and output voltage ratings may
be exceeded if the input and output clamp-current ratings are observed.
Device
VCC
+IIK
+IOK
Logic
Input
-IIK
Output
-IOK
GND
Figure 6. Electrical Placement of Clamping Diodes for Each Input and Output
8.4 Device Functional Modes
Table 1. Function Table
INPUTS
OUTPUT
OE
A
Y
L
H
H
L
L
L
H
X
Z
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
9
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
In this application, a buffer with 3-state output is used to disable a data signal as shown in Figure 7. The
remaining three buffers can be used for other applications in the system, or the inputs can be grounded and the
channels left unused.
9.2 Typical Application
System
Controller
OE
Data
A
Y
Output
Figure 7. Typical application block diagram
9.2.1 Design Requirements
9.2.1.1 Power Considerations
Ensure the desired supply voltage is within the range specified in the Recommended Operating Conditions. The
supply voltage sets the device's electrical characteristics as described in the Electrical Characteristics.
The supply must be capable of sourcing current equal to the total current to be sourced by all outputs of the
CD74HC125-Q1 plus the maximum supply current, ICC, listed in the Electrical Characteristics. The logic device
can only source or sink as much current as it is provided at the supply and ground pins, respectively. Be sure not
to exceed the maximum total current through GND or VCC listed in the Absolute Maximum Ratings.
Total power consumption can be calculated using the information provided in CMOS Power Consumption and
Cpd Calculation.
Thermal increase can be calculated using the information provided in Thermal Characteristics of Standard Linear
and Logic (SLL) Packages and Devices.
CAUTION
The maximum junction temperature, TJ(max) listed in the Absolute Maximum Ratings,
is an additional limitation to prevent damage to the device. Do not violate any values
listed in the Absolute Maximum Ratings. These limits are provided to prevent damage
to the device.
9.2.1.2 Input Considerations
Unused inputs must be terminated to either VCC or ground. These can be directly terminated if the input is
completely unused, or they can be connected with a pull-up or pull-down resistor if the input is to be used
sometimes, but not always. A pull-up resistor is used for a default state of HIGH, and a pull-down resistor is used
for a default state of LOW. The resistor size is limited by drive current of the controller, leakage current into the
CD74HC125-Q1, as specified in the Electrical Characteristics, and the desired input transition rate. A 10-kΩ
resistor value is often used due to these factors.
10
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
Typical Application (continued)
The CD74HC125-Q1 has standard CMOS inputs, so input signal edge rates cannot be slow. Slow input edge
rates can cause oscillations and damaging shoot-through current. The recommended rates are defined in the
Recommended Operating Conditions.
Refer to the Feature Description for additional information regarding the inputs for this device.
9.2.1.3 Output Considerations
The positive supply voltage is used to produce the output HIGH voltage. Drawing current from the output will
decrease the output voltage as specified by the VOH specification in the Electrical Characteristics. Similarly, the
ground voltage is used to produce the output LOW voltage. Sinking current into the output will increase the
output voltage as specified by the VOL specification in the Electrical Characteristics.
Unused outputs can be left floating. Do not connect outputs directly to VCC or ground.
Refer to Feature Description for additional information regarding the outputs for this device.
9.2.2 Detailed Design Procedure
1. Add a decoupling capacitor from VCC to GND. The capacitor needs to be placed physically close to the
device and electrically close to both the VCC and GND pins. An example layout is shown in the Layout.
2. Ensure the capacitive load at the output is ≤ 70 pF. This is not a hard limit, however it will ensure optimal
performance. This can be accomplished by providing short, appropriately sized traces from the CD74HC125Q1 to the receiving device.
3. Ensure the resistive load at the output is larger than (VCC / IO(max)) Ω. This will ensure that the maximum
output current from the Absolute Maximum Ratings is not violated. Most CMOS inputs have a resistive load
measured in megaohms; much larger than the minimum calculated above.
4. Thermal issues are rarely a concern for logic gates, however the power consumption and thermal increase
can be calculated using the steps provided in the application report, CMOS Power Consumption and Cpd
Calculation
9.2.3 Application Curves
OE
Data
Output
Figure 8. Application timing diagram
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
11
CD74HC125-Q1
SCLS579B – APRIL 2004 – REVISED APRIL 2020
www.ti.com
10 Power Supply Recommendations
The power supply can be any voltage between the minimum and maximum supply voltage rating located in the
Recommended Operating Conditions. Each VCC terminal should have a bypass capacitor to prevent power
disturbance. A 0.1-μF capacitor is recommended for this device. It is acceptable to parallel multiple bypass caps
to reject different frequencies of noise. The 0.1-μF and 1-μF capacitors are commonly used in parallel. The
bypass capacitor should be installed as close to the power terminal as possible for best results, as shown in
Figure 9.
11 Layout
11.1 Layout Guidelines
When using multiple-input and multiple-channel logic devices inputs must not ever be left floating. In many
cases, functions or parts of functions of digital logic devices are unused; for example, when only two inputs of a
triple-input AND gate are used. Such unused input pins must not be left unconnected because the undefined
voltages at the outside connections result in undefined operational states. All unused inputs of digital logic
devices must be connected to a logic high or logic low voltage, as defined by the input voltage specifications, to
prevent them from floating. The logic level that must be applied to any particular unused input depends on the
function of the device. Generally, the inputs are tied to GND or VCC, whichever makes more sense for the logic
function or is more convenient.
11.2 Layout Example
GND VCC
Recommend GND flood fill for
improved signal isolation, noise
reduction, and thermal dissipation
0.1 F
Avoid 90°
corners for
signal lines
Bypass capacitor
placed close to the
device
1OE
1
14
VCC
1A
2
13
4OE
1Y
3
12
4A
2OE
4
11
4Y
2A
5
10
3OE
2Y
6
9
3A
GND
7
8
3Y
Unused
inputs tied
to VCC
Unused
output left
floating
Figure 9. Example layout for the CD74HC125-Q1
12
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
CD74HC125-Q1
www.ti.com
SCLS579B – APRIL 2004 – REVISED APRIL 2020
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• HCMOS Design Considerations
• CMOS Power Consumption and CPD Calculation
• Designing with Logic
12.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
12.3 Community Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2004–2020, Texas Instruments Incorporated
Product Folder Links: CD74HC125-Q1
13
PACKAGE OPTION ADDENDUM
www.ti.com
28-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
CD74HC125QM96G4Q1
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HC125Q
CD74HC125QPWRG4Q1
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HC125Q
CD74HC125QPWRQ1
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
HC125Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of