CD74HCT258E

CD54HCT258, CD74HCT258 QUADRUPLE 2-LINE TO 1-LINE SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS SCHS276A – MAY 2003 D D D D D D CD54HCT258 . . . F PACKAGE CD74HCT258 . . . E PACKAGE (TOP VIEW) 4.5-V to 5.5-V VCC Operation Wide Operating Temperature Range of –55°C to 125°C Balanced Propagation Delays and Transition Times Standard Outputs Drive Up To 10 LS-TTL Loads Significant Power Reduction Compared to LS-TTL Logic ICs Inputs Are TTL-Voltage Compatible A/B 1A 1B 1Y 2A 2B 2Y GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC G 4A 4B 4Y 3A 3B 3Y description/ordering information These devices are designed to multiplex signals from 4-bit data sources to 4-output data lines in bus-organized systems. The 3-state outputs do not load the data lines when the output-enable (G) input is at a high logic level. To ensure the high-impedance state during power up or power down, G should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION –55°C 55°C to 125°C ORDERABLE PART NUMBER PACKAGE† TA TOP-SIDE MARKING PDIP – E Tube CD74HCT258E CD74HCT258E CDIP – F Tube CD54HCT258F3A CD54HCT258F3A † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE INPUTS OUTPUT Y G A/B A B H X X X Z L L L X H L L H X L L H X L H L H X H L Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 CD54HCT258, CD74HCT258 QUADRUPLE 2-LINE TO 1-LINE SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS SCHS276A – MAY 2003 logic diagram (positive logic) G A/B 1A 1B 2A 2B 3A 3B 4A 4B 15 1 2 4 1Y 3 5 7 2Y 6 11 9 3Y 10 14 12 4Y 13 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous output drain current per output, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±35 mA Continuous output source or sink current per output, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 2): E package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 CD54HCT258, CD74HCT258 QUADRUPLE 2-LINE TO 1-LINE SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS SCHS276A – MAY 2003 recommended operating conditions (see Note 3) VCC VIH Supply voltage VIL VI Low-level input voltage VO ∆t/∆v Output voltage High-level input voltage MIN MAX 4.5 5.5 2 Input voltage Input transition rise or fall rate UNIT V V 0.8 V VCC VCC V 500 ns V TA Operating free-air temperature –55 125 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC VOH VI = VIH or VIL IOH = –20 µA IOH = –6 mA 45V 4.5 VOL VI = VIH or VIL IOL = 20 µA IOL = 6 mA 45V 4.5 II IOZ VI = VCC or 0 VO = VCC or 0 ICC VI = VCC or 0, ∆ICC† One input at VCC – 2.1 V, Other inputs at 0 or VCC TA = 25°C TA = –55°C TO 125°C TA = –40°C TO 85°C MIN MIN MIN MAX MAX 4.4 4.4 4.4 3.98 3.7 3.84 UNIT MAX V 0.1 0.1 0.1 0.26 0.4 0.33 5.5 V ±0.1 ±1 ±1 µA 5.5 V ±0.5 ±10 ±5 µA 5.5 V 8 160 80 µA 360 490 450 µA Ci 10 10 10 pF Co 20 20 20 IO = 0 4.5 V to 5.5 V 100 V pF † Additional quiescent supply current per input pin, TTL inputs high, 1 unit load. For dual-supply systems, theoretical worst-case (VI = 2.4 V, VCC = 5.5 V) specification is 1.8 mA. HCT INPUT LOADING TABLE INPUT UNIT LOAD G 1.5 A or B 0.5 A/B 1.5 Unit Load is ∆ICC limit specified in electrical characteristics table (e.g., 360 µA max at 25°C). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 CD54HCT258, CD74HCT258 QUADRUPLE 2-LINE TO 1-LINE SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS SCHS276A – MAY 2003 switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A or B Any Y tpd d A/B Any Y ten G Any Y tdis di G Any Y tt Any Y LOAD CAPACITANCE VCC CL = 50 pF 4.5 V TA = 25°C MIN CL = 15 pF 5V CL = 50 pF 4.5 V CL = 15 pF 5V CL = 50 pF 4.5 V CL = 15 pF 5V CL = 50 pF 4.5 V CL = 15 pF 5V TYP MAX TA = –55°C TO 125°C TA = –40°C TO 85°C MIN MIN MAX UNIT MAX 27 41 34 34 51 43 28 42 35 30 45 38 12 18 15 11 ns 14 11 12 CL = 50 pF ns ns ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER TYP Power dissipation capacitance per multiplexer† Cpd † Cpd is used to determine the dynamic power consumption per multiplexer. PD = VCC2fi (Cpd + CL) where: PD = dynamic power dissipation fi = input frequency CL = output load capacitance VCC = supply voltage 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 49 UNIT pF CD54HCT258, CD74HCT258 QUADRUPLE 2-LINE TO 1-LINE SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS SCHS276A – MAY 2003 PARAMETER MEASUREMENT INFORMATION VCC Test Point From Output Under Test PARAMETER S1 ten 1 kΩ tdis CL (see Note A) S2 S1 S2 tPZH Open Closed tPZL Closed Open tPHZ Open Closed tPLZ Closed Open Open Open tpd or tt tw LOAD CIRCUIT 3V 1.3 V Input 1.3 V 0V VOLTAGE WAVEFORMS PULSE DURATION CLR Input 3V Reference Input 3V 1.3 V 1.3 V 0V 0V tsu trec Data 1.3 V Input 0.3 V 3V 1.3 V CLK th 2.7 V 3V 2.7 V 1.3 V 0.3 V 0 V tf tr 0V VOLTAGE WAVEFORMS RECOVERY TIME VOLTAGE WAVEFORMS SETUP AND HOLD AND INPUT RISE AND FALL TIMES 3V Input 1.3 V 1.3 V 0V tPLH In-Phase Output 1.3 V 10% 90% tPHL 90% 1.3 V 1.3 V 0V tPHL 90% tr Out-of-Phase Output 3V Output Control VOH 1.3 V 10% tf VOL 1.3 V 10% tf 1.3 V 10% tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES 1.3 V Output Waveform 2 (see Note B) 10% VOL tPHZ tPZH VOH VOL ≈VCC Output Waveform 1 (see Note B) tPLH 90% tPLZ tPZL 1.3 V 90% VOH ≈0 V VOLTAGE WAVEFORMS OUTPUT ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns. D. For clock inputs, fmax is measured with the input duty cycle at 50%. E. The outputs are measured one at a time with one input transition per measurement. F. tPLZ and tPHZ are the same as tdis. G. tPZL and tPZH are the same as ten. H. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 4-Feb-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking (4/5) (6) 5962-8970801EA ACTIVE CDIP J 16 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8970801EA CD54HCT258F3A CD54HCT258F3A ACTIVE CDIP J 16 1 Non-RoHS & Green SNPB N / A for Pkg Type -55 to 125 5962-8970801EA CD54HCT258F3A CD74HCT258E ACTIVE PDIP N 16 25 RoHS & Green NIPDAU N / A for Pkg Type -55 to 125 CD74HCT258E (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of