CD74HCT74, CD54HCT74
SCHS409 – JUNE 2020
CDx4HCT74 Dual D-Type Positive-Edge-Triggered Flip-Flops With Clear and Preset
1 Features
3 Description
•
The
CDx4HCT74-Q1
devices
contain
two
independent D-type positive-edge-triggered flip-flops
with asynchronous preset and clear pins for each.
•
•
•
•
•
•
LSTTL input logic compatible
– VIL(max) = 0.8 V, VIH(min) = 2 V
CMOS input logic compatible
– II ≤ 1 µA at VOL, VOH
Buffered inputs
4.5 V to 5.5 V operation
Wide operating temperature range:
-55°C to +125°C
Supports fanout up to 10 LSTTL loads
Significant power reduction compared to LSTTL
logic ICs
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
CD74HCT74M
SOIC (14)
8.70 mm × 3.90 mm
CD74HCT74E
PDIP (14)
19.30 mm × 6.40 mm
CD54HCT74F
CDIP (14)
21.30 mm × 7.60 mm
(1)
For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
•
•
Convert a momentary switch to a toggle switch
Divide a clock signal by 2 or 4
xCLK
C
C
xPRE
C
xQ
C
C
C
xD
C
C
C
xQ
C
xCLR
Functional block diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
Pin Functions.................................................................... 3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 Recommended Operating Conditions.........................4
6.3 Thermal Information....................................................4
6.4 Electrical Characteristics.............................................5
6.5 Timing Requirements.................................................. 5
6.6 Switching Characteristics............................................5
6.7 Operating Characteristics........................................... 6
6.8 Typical Characteristics................................................ 6
7 Parameter Measurement Information............................ 7
8 Detailed Description........................................................8
8.1 Overview..................................................................... 8
8.2 Functional Block Diagram........................................... 8
8.3 Feature Description.....................................................8
8.4 Device Functional Modes............................................9
9 Application and Implementation.................................. 10
9.1 Application Information............................................. 10
9.2 Typical Application.................................................... 10
10 Power Supply Recommendations..............................13
11 Layout........................................................................... 14
11.1 Layout Guidelines................................................... 14
11.2 Layout Example...................................................... 14
12 Device and Documentation Support..........................15
12.1 Documentation Support.......................................... 15
12.2 Support Resources................................................. 15
12.3 Trademarks............................................................. 15
12.4 Electrostatic Discharge Caution..............................15
12.5 Glossary..................................................................15
13 Mechanical, Packaging, and Orderable
Information.................................................................... 15
4 Revision History
2
DATE
REVISION
NOTES
June 2020
*
Initial release. Moved the HCT devices from
the SCHS124 to a standalone data sheet.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
5 Pin Configuration and Functions
1CLR
1
14
VCC
1D
2
13
2CLR
1CLK
3
12
2D
1PRE
4
11
2CLK
1Q
5
10
1Q
6
9
2Q
GND
7
8
2Q
2PRE
Figure 5-1. D, N, or J Package 14-Pin SOIC, PDIP, or CDIP Top View
Pin Functions
PIN
I/O
DESCRIPTION
NAME
NO.
1 CLR
1
Input
Channel 1, Clear Input, Active Low
1D
2
Input
Channel 1, Data Input
1CLK
3
Input
Channel 1, Positive edge triggered clock input
1 PRE
4
Input
Channel 1, Preset Input, Active Low
1Q
5
Output
Channel 1, Output
1Q
6
Output
Channel 1, Inverted Output
GND
7
—
2Q
8
Output
Channel 2, Inverted Output
2Q
9
Output
Channel 2, Output
2 PRE
10
Input
Channel 2, Preset Input, Active Low
2CLK
11
Input
Channel 2, Positive edge triggered clock input
2D
12
Input
Channel 2, Data Input
2 CLR
13
Input
Channel 2, Clear Input, Active Low
VCC
14
—
Copyright © 2021 Texas Instruments Incorporated
Ground
Positive Supply
Submit Document Feedback
3
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
–0.5
7
UNIT
VCC
Supply voltage
IIK
Input clamp current(2)
VI < –0.5 V or VI > VCC +
0.5 V
±20
mA
IOK
Output clamp current(2)
VO < –0.5 V or VO > VCC +
0.5 V
±20
mA
IO
Continuous output current
VO > –0.5 V or VO < VCC +
0.5 V
±25
mA
±50
mA
Hermetic Package or Die
175
°C
Plastic Package
150
°C
300
°C
150
°C
Continuous current through VCC or GND
Junction temperature(3)
TJ
Lead temperature (soldering 10s)
Tstg
(1)
(2)
(3)
SOIC - lead tips only
Storage temperature
–65
V
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated
under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
Guaranteed by design.
6.2 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VCC
Supply voltage
VIH
High-level input voltage
VCC = 4.5 V to 5.5 V
VCC = 4.5 V to 5.5 V
VIL
Low-level input voltage
VI
Input voltage
VO
Output voltage
tt
Input transition time
TA
Operating free-air temperature
4.5
NOM
MAX
5.5
2
UNIT
V
V
0.8
V
0
VCC
V
0
VCC
V
VCC = 4.5 V
500
VCC = 5.5 V
400
–55
125
ns
°C
6.3 Thermal Information
CD74HCT74
THERMAL METRIC(1)
D (SOIC)
UNIT
14 PINS
14 PINS
RθJA
Junction-to-ambient thermal resistance
62.3
88.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
50.0
47.5
°C/W
RθJB
Junction-to-board thermal resistance
42.0
43.8
°C/W
ΨJT
Junction-to-top characterization parameter
29.6
13.7
°C/W
ΨJB
Junction-to-board characterization parameter
41.8
43.5
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
°C/W
(1)
4
N (PDIP)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
6.4 Electrical Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
Operating free-air temperature (TA)
PARAMETER
TEST CONDITIONS
VCC
25°C
MIN
VOH
VOL
High-level
output voltage
IOH = –20
VI = VIH or µA
VIL
IOH = –4
mA
–40°C to 85°C
TYP
MAX
MIN
TYP
–55°C to 125°C
MAX
MIN
4.5 V
4.4
4.4
4.4
4.5 V
3.98
3.84
3.7
TYP
UNIT
MAX
V
IOL = 20
4.5 V
Low-level output VI = VIH or µA
voltage
VIL
IOL = 4 mA 4.5 V
0.1
0.1
0.1
0.26
0.33
0.4
V
II
Input leakage
current
VI = VCC
and GND
IO = 0
5.5 V
±0.1
±1
±1
µA
ICC
Supply current
VI = VCC or
IO = 0
GND
5.5 V
4
40
80
µA
(1)
Additional
Quiescent
Device Current
Per Input Pin.
VI = VCC –
2.1
4.5 V
to 5.5
V
360
450
490
µA
Ci
Input
capacitance
10
10
10
pF
ΔICC
(1)
100
5V
For dual-supply systems theoretical worst case (VI = 2.4 V, VCC = 5.5 V) specification is 1.8 mA.
6.5 Timing Requirements
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
Operating free-air temperature (TA)
VCC
25°C
MIN
tsu
Setup time
th
Hold time
trem
Removal time
tw
Pulse width
fmax
CLK frequency
D to CLK
TYP
–40°C to 85°C
MAX
MIN
TYP
–55°C to 125°C
MAX
MIN
TYP
UNIT
MAX
4.5 V
12
15
18
ns
4.5 V
3
3
3
ns
CLR, PRE, to
4.5 V
CLK
6
8
9
ns
CLR, PRE
4.5 V
16
20
24
CLK
4.5 V
18
23
27
4.5 V
25
20
16
ns
MHz
6.6 Switching Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
PARAMETER
tpd
Propagation delay
tt
Transition-time
fmax
CLK Frequency
FROM
TO
TEST
CONDITIO
NS
Operating free-air temperature (TA)
VCC
25°C
–40°C to 85°C
–55°C to 125°C
MIN TYP MAX
MIN TYP MAX
MIN TYP MAX
CLK
Q, Q
CL = 50 pF
4.5 V
35
44
53
CLR,
PRE
Q, Q
CL = 50 pF
4.5 V
40
50
60
Y
CL = 50 pF
4.5 V
15
19
22
CL = 15 pF
5V
Copyright © 2021 Texas Instruments Incorporated
UNIT
ns
ns
50
Submit Document Feedback
5
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
6.7 Operating Characteristics
over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
Power dissipation capacitance
No load
per gate
Cpd
VCC
MIN
5V
TYP
MAX UNIT
30
pF
6.8 Typical Characteristics
TA = 25°C
0.3
7
VOL Output Low Voltage (V)
VOH Output High Voltage (V)
6
5
4
3
2
2-V
4.5-V
6-V
1
0
0.25
0.2
0.15
0.1
0.05
0
0
1
2
3
4
IOH Output High Current (mA)
5
6
Figure 6-1. Typical output voltage in the high state
(VOH)
6
2-V
4.5-V
6-V
Submit Document Feedback
0
1
2
3
4
IOL Output Low Current (mA)
5
6
Figure 6-2. Typical output voltage in the low state
(VOL)
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
7 Parameter Measurement Information
•
•
Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators
having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tt < 6 ns.
The outputs are measured one at a time, with one input transition per measurement.
Test
Point
90%
VCC
90%
Input
10%
10%
tr(1)
From Output
Under Test
CL(1)
0V
tf(1)
90%
VOH
90%
Output
10%
A.
10%
tr(1)
CL= 50 pF and includes probe and jig capacitance.
A.
Figure 7-1. Load Circuit
tt is the greater of tr and tf.
tw
VCC
50%
Input
0V
tsu
50%
50%
0V
th
Figure 7-4. Voltage Waveforms Pulse Width
VCC
Data
Input
VOL
Figure 7-2. Voltage Waveforms Transition Times
VCC
Clock
Input
tf(1)
50%
50%
0V
Figure 7-3. Voltage Waveforms Setup and Hold
Times
VCC
Input
50%
50%
0V
tPLH
(1)
tPHL
(1)
VOH
Output
50%
50%
VOL
tPLH(1)
tPHL(1)
VOH
Output
50%
50%
VOL
A.
The maximum between tPLH and tPHL is used for tpd.
Figure 7-5. Voltage Waveforms Propagation Delays
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
8 Detailed Description
8.1 Overview
The CDx4HCT74-Q1 devices contain two independent D-type positive-edge-triggered flip-flops with
asynchronous preset and clear pins for each.
8.2 Functional Block Diagram
xCLK
C
C
xPRE
C
xQ
C
C
C
xD
C
C
C
xQ
C
xCLR
8.3 Feature Description
8.3.1 Balanced CMOS Push-Pull Outputs
A balanced output allows the device to sink and source similar currents. The drive capability of this device
may create fast edges into light loads so routing and load conditions should be considered to prevent ringing.
Additionally, the outputs of this device are capable of driving larger currents than the device can sustain without
being damaged. It is important for the output power of the device to be limited to avoid damage due to
over-current. The electrical and thermal limits defined in the Section 6.1 must be followed at all times.
The CD74HCT74 can drive a load with a total capacitance less than or equal to the maximum load listed in the
Section 6.6 connected to a high-impedance CMOS input while still meeting all of the datasheet specifications.
Larger capacitive loads can be applied, however it is not recommended to exceed the provided load value. If
larger capacitive loads are required, it is recommended to add a series resistor between the output and the
capacitor to limit output current to the values given in the Section 6.1.
8.3.2 TTL-Compatible CMOS Inputs
TTL-Compatible CMOS inputs are high impedance and are typically modeled as a resistor from the input to
ground in parallel with the input capacitance given in the Section 6.4. The worst case resistance is calculated
with the maximum input voltage, given in the Section 6.1, and the maximum input leakage current, given in the
Section 6.4, using ohm's law (R = V ÷ I).
Signals applied to the inputs need to have fast edge rates, as defined by Δt/Δv in the Section 6.2 to avoid
excessive current consumption and oscillations. If a slow or noisy input signal is required, a device with a
Schmitt-trigger input should be used to condition the input signal prior to the TTL-compatible CMOS input.
TTL-Compatible CMOS inputs have a lower threshold voltage than standard CMOS inputs to allow for
compatibility with older bipolar logic devices. See the Section 6.2 for the valid input voltages for the
CD74HCT74.
8
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
8.3.3 Clamp Diode Structure
The inputs and outputs to this device have both positive and negative clamping diodes as depicted in Figure 8-1.
CAUTION
Voltages beyond the values specified in the Section 6.1 table can cause damage to the device.
The recommended input and output voltage ratings may be exceeded if the input and output clampcurrent ratings are observed.
VCC
Device
+IIK
+IOK
Logic
Input
Output
-IIK
-IOK
GND
Figure 8-1. Electrical Placement of Clamping Diodes for Each Input and Output
8.4 Device Functional Modes
Table 8-1. Function Table
INPUTS
(1)
OUTPUTS
PRE
CLR
CLK
D
Q
Q
L
H
X
X
H
L
H
L
X
X
L
H
L
L
X
X
H(1)
H(1)
H
H
↑
H
H
L
H
H
↑
L
L
H
H
H
L
X
Q0
Q0
This configuration is nonstable; that is, it does not persist when
PRE or CLR returns to its inactive (high) level.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 Application Information
Toggle switches are typically large, mechanically complex and relatively expensive. It is desirable to use a
momentary switch instead because they are small, mechanically simple and low cost. Some systems require a
toggle switch's functionality but are space or cost constrained and must use a momentary switch instead.
If the data input (D) of the D-type flip-flop is tied to the inverted output ( Q), then each clock pulse will cause
the value at the output (Q) to toggle. The momentary switch can be debounced and connected through a
Schmitt-trigger buffer to the clock input (CLK) to toggle the output.
This application also utilizes a power-on reset circuit to ensure that the output always starts in the LOW state
when power is applied.
9.2 Typical Application
VCC
R1
R2
C1
VCC
VCC
R3
PRE
D
CLK
Q
CLR
Q
Output
C2
Figure 9-1. Typical application schematic
9.2.1 Design Requirements
9.2.1.1 Power Considerations
Ensure the desired supply voltage is within the range specified in the Section 6.2. The supply voltage sets the
device's electrical characteristics as described in the Section 6.4.
The supply must be capable of sourcing current equal to the total current to be sourced by all outputs of the
CD74HCT74 plus the maximum supply current, ICC, listed in the Section 6.4. The logic device can only source
or sink as much current as it is provided at the supply and ground pins, respectively. Be sure not to exceed the
maximum total current through GND or VCC listed in the Section 6.1.
Total power consumption can be calculated using the information provided in CMOS Power Consumption and
Cpd Calculation.
Thermal increase can be calculated using the information provided in Thermal Characteristics of Standard Linear
and Logic (SLL) Packages and Devices.
10
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
CAUTION
The maximum junction temperature, TJ(max) listed in the Section 6.1, is an additional limitation to
prevent damage to the device. Do not violate any values listed in the Section 6.1. These limits are
provided to prevent damage to the device.
9.2.1.2 Input Considerations
Unused inputs must be terminated to either VCC or ground. These can be directly terminated if the input is
completely unused, or they can be connected with a pull-up or pull-down resistor if the input is to be used
sometimes, but not always. A pull-up resistor is used for a default state of HIGH, and a pull-down resistor is used
for a default state of LOW. The resistor size is limited by drive current of the controller, leakage current into the
CD74HCT74, as specified in the Section 6.4, and the desired input transition rate. A 10-kΩ resistor value is often
used due to these factors.
Refer to the Section 8.3 for additional information regarding the inputs for this device.
9.2.1.3 Output Considerations
The positive supply voltage is used to produce the output HIGH voltage. Drawing current from the output will
decrease the output voltage as specified by the VOH specification in the Section 6.4. Similarly, the ground voltage
is used to produce the output LOW voltage. Sinking current into the output will increase the output voltage as
specified by the VOL specification in the Section 6.4.
Unused outputs can be left floating. Do not connect outputs directly to VCC or ground.
Refer to Section 8.3 for additional information regarding the outputs for this device.
9.2.1.4 Timing Considerations
The CD74HCT74 is a clocked device. As such, it requires special timing considerations to ensure normal
operation.
Primary timing factors to consider:
•
•
•
•
Maximum clock frequency: the maximum operating clock frequency defined in Section 6.5 is the maximum
frequency at which the device is guaranteed to function. This value refers specifically to the triggering
waveform, measuring from one trigger level to the next.
Pulse duration: ensure that the triggering event duration is larger than the minimum pulse duration, as
defined in the Section 6.5.
Setup time: ensure that the data has changed at least one setup time prior to the triggering event, as defined
in the Section 6.5.
Hold time: ensure that the data remains in the desired state at least one hold time after the triggering event,
as defined in the Section 6.5.
9.2.2 Detailed Design Procedure
1. Add a decoupling capacitor from VCC to GND. The capacitor needs to be placed physically close to the
device and electrically close to both the VCC and GND pins. An example layout is shown in the Section 11.
2. Ensure the capacitive load at the output is ≤ 70 pF. This is not a hard limit, however it will ensure optimal
performance. This can be accomplished by providing short, appropriately sized traces from the CD74HCT74
to the receiving device.
3. Ensure the resistive load at the output is larger than (VCC / IO(max)) Ω. This will ensure that the maximum
output current from the Section 6.1 is not violated. Most CMOS inputs have a resistive load measured in
megaohms; much larger than the minimum calculated above.
4. Thermal issues are rarely a concern for logic gates, however the power consumption and thermal increase
can be calculated using the steps provided in the application report, CMOS Power Consumption and Cpd
Calculation
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
Voltage (2 V/div)
Voltage (2 V/div)
9.2.3 Application Curves
Vout
Vin
Vout
Vin
Time (200 ms/div)
Time (100 Ps/div)
D001
Figure 9-2. Waveform for non-debounced switch.
12
Submit Document Feedback
D002
Figure 9-3. Waveform for debounced switch.
Copyright © 2021 Texas Instruments Incorporated
www.ti.com
CD74HCT74, CD54HCT74
SCHS409 – JUNE 2020
10 Power Supply Recommendations
The power supply can be any voltage between the minimum and maximum supply voltage rating located in
the Section 6.2. Each VCC terminal should have a bypass capacitor to prevent power disturbance. A 0.1-μF
capacitor is recommended for this device. It is acceptable to parallel multiple bypass caps to reject different
frequencies of noise. The 0.1-μF and 1-μF capacitors are commonly used in parallel. The bypass capacitor
should be installed as close to the power terminal as possible for best results, as shown in Figure 11-1.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
11 Layout
11.1 Layout Guidelines
When using multiple-input and multiple-channel logic devices inputs must not ever be left floating. In many
cases, functions or parts of functions of digital logic devices are unused; for example, when only two inputs of
a triple-input AND gate are used. Such unused input pins must not be left unconnected because the undefined
voltages at the outside connections result in undefined operational states. All unused inputs of digital logic
devices must be connected to a logic high or logic low voltage, as defined by the input voltage specifications, to
prevent them from floating. The logic level that must be applied to any particular unused input depends on the
function of the device. Generally, the inputs are tied to GND or VCC, whichever makes more sense for the logic
function or is more convenient.
11.2 Layout Example
GND VCC
Recommend GND flood fill for
improved signal isolation, noise
reduction, and thermal dissipation
0.1 F
Unused input
tied to GND
Avoid 90°
corners for
signal lines
Bypass capacitor
placed close to the
device
1CLR
1
14
VCC
Unused inputs
tied to VCC
1D
2
13
2CLR
1CLK
3
12
2D
1PRE
4
11
2CLK
1Q
5
10
2PRE
1Q
6
9
2Q
GND
7
8
2Q
Unused output
left floating
Figure 11-1. Example layout for the CD74HCT74
14
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
CD74HCT74, CD54HCT74
www.ti.com
SCHS409 – JUNE 2020
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• HCMOS Design Considerations
• CMOS Power Consumption and CPD Calculation
• Designing with Logic
12.2 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.3 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.5 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
5962-8685301CA
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-8685301CA
CD54HCT74F3A
Samples
CD54HCT74F
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
CD54HCT74F
Samples
CD54HCT74F3A
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-8685301CA
CD54HCT74F3A
Samples
CD74HCT74E
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-55 to 125
CD74HCT74E
Samples
CD74HCT74M
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
HCT74M
Samples
CD74HCT74M96
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU | SN
Level-1-260C-UNLIM
-55 to 125
HCT74M
Samples
CD74HCT74M96G4
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
HCT74M
Samples
CD74HCT74ME4
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
HCT74M
Samples
CD74HCT74MT
ACTIVE
SOIC
D
14
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-55 to 125
HCT74M
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of