CLC404AJM5X

CLC404 Wideband, High Slew Rate, Monolithic Op Amp General Description Features The CLC404 is a high speed, monolithic op amp that combines low power consumption (110mW typical, 120mW maximum) with superior large signal performance. Operating off of ± 5V supplies, the CLC404 demonstrates a large signal bandwidth (5VPP output) of 165MHz. The bandwidth performance, along with other speed characteristics such as rise and fall time (2.1ns for a 5V step), is nearly identical to the small signal performance since slew rate is not limiting factor in the CLC404 design. With its 175MHz bandwidth and 10ns settling (0.2%), the CLC404 is ideal for driving ultra fast flash A/D converters. The 0.5˚ deviation from linear phase, coupled with -53dBc 2nd harmonic distortion and -60dBc 3rd harmonic distortion (both at 20MHz), is well suited for many digital and analog communication applications. These same characteristics, along with 70mA output current, differential gain of 0.07%, and differential phase at 0.03˚, make the CLC404 an appropriate high performance solution for video distribution and line driving applications. Constructed using an advanced, complementary bipolar process and proven current feedback topologies, the CLC404 provides performance far beyond that of other monolithic op amps. The CLC404 is available in several versions to meet a variety of requirements. Enhanced Solutions (Military/Aerospace) SMD Number: 5962-90994 Space level versions also available. For more information, visit http://www.national.com/mil n n n n n n 165MHz large signal bandwidth (5VPP) 2600V/µs slew rate Low Power: 110mW Low distortion: −53dBc at 20MHz 10ns settling to 0.2% 0.07% diff. gain, 0.03˚ diff. phase Applications n n n n n Fast A/D conversion Line drivers Video distribution High speed communications Radar, IF processors Large Signal Pulse Response 01274607 Connection Diagrams 01274619 Pinout DIP & SOIC 01274618 Pinout SOT 23-5 © 2001 National Semiconductor Corporation DS012746 www.national.com CLC404 Wideband, High Slew Rate, Monolithic Op Amp June 2001 CLC404 Absolute Maximum Ratings (Note 1) Operating Temperature Range −40˚C to +85˚C Storage Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. −65˚C to +150˚C Lead Solder Duration (+300˚C) 10 sec ESD rating (human body model) 500V ± 7V Supply Voltage (VCC) IOUT Output is short circuit protected to ground, but maximum reliability will be maintained if IOUT does not exceed... (θJC) (θJA) 60mA MDIP 65˚C/W 120˚C/W Common Mode Input Voltage ± VCC SOIC 60˚C/W 140˚C/W Differential Input Voltage Junction Temperature Operating Ratings Thermal Resistance Package 10V +150˚C Electrical Characteristics AV = +6, VCC = ± 5V, Rg & RL =100Ω, Rf = 500Ω; unless specified Symbol Parameter Ambient Temperature Conditions Typ Max/Min Ratings (Note 2) Units CLC404AJ +25˚C −40˚C +25˚C +85˚C > 150 > 140 > 140 > 140 > 120 > 110 MHz < 0.4 < 0.7 < 1.0 < 1.0 < 0.3 < 0.5 < 1.1 < 1.0 < 0.4 < 0.7 < 1.3 < 1.2 dB < 2.4 < 2.6 < 15 < 15 > 2000 < 2.4 < 2.6 < 15 < 12 > 2000 < 2.9 < 3.2 < 15 < 15 > 2000 ns Frequency Domain Response SSBW -3dB Bandwidth VOUT < 2VPP 175 LSBW -3dB Large Signal VOUT < 5VPP 165 Gain Flatness VOUT < 2VPP < 40MHz > 40MHz < 75MHz GFPL Peaking GFPH Peaking GFR Rolloff LPD Linear Phase Deviation 0 0 0.2 DC to 75MHz 0.5 Rise and Fall Time 2V Step 2.0 5V Step 2.1 TS Settling Time to ± 0.2% 2V Step 10 OS Overshoot 2V Step 5 SR Slew Rate (Measured at AV +2) (Note 4) MHz dB dB deg Time Domain Response TRS TRL 2600 ns ns % V/µs Distortion And Noise Response HD2 2nd Harmonic Distortion 2VPP,20MHz −53 3rd Harmonic Distortion 2VPP,20MHz −60 < −40 < −50 < −45 < −50 < −45 < −50 dBc HD3 dBc Equivalent Input Noise SNF Noise Floor > 1MHz −159 < −157 < −157 < −156 dBm (1Hz) INV Integrated Noise 1MHz to 200MHz 40 < 45 < 45 < 50 µV DG Differential Gain (Note 3) 0.07 - - - % DP Differential Phase (Note 3) 0.03 - - - ˚ 2 < ± 9.0 < ± 50 < ± 44 < ± 275 < ± 40 < ± 275 > 45 > 44 < ± 5.0 < ± 10.0 < ± 50 < ± 22 < ± 200 < ± 22 < ± 200 > 45 > 44 mV Static, DC Performance VIO Input Offset Voltage (Note 5) DVIO IBN Average Temperature Coefficient Input Bias Current (Note 5) DIBN IBI 30 Non Inverting 15 Average Temperature Coefficient Input Bias Current (Note 5) DIBI 150 Inverting 15 Average Temperature Coefficient 150 PSRR Power Supply Rejection Ratio 52 CMRR Common Mode Rejection Ration 50 www.national.com 2 - < ± 22 - < ± 18 - > 48 > 46 µV/˚C µA nA/˚C µA nA/C˚ dB dB CLC404 Electrical Characteristics (Continued) AV = +6, VCC = ± 5V, Rg & RL =100Ω, Rf = 500Ω; unless specified Symbol ICC Parameter Conditions Supply Current (Note 5) Typ Max/Min Ratings (Note 2) Units No Load, Quiescent 11 < 12 < 12 < 12 mA Resistance 1000 > 250 ± 2.8 > ± 1.4 > ± 35 > 500 ± 3.0 > ± 1.8 > ± 50 > 1000 ± 3.0 > ± 2.0 > ± 50 kΩ Miscellaneous Performance RIN Non-Inverting Input CIN Capacitance 1 RO Output Impedence At DC 0.1 VO Output Voltage Range No Load CMIR Common Mode Input Range For Rated Performance IO Output Current ± 3.3 ± 2.2 ± 60 pF Ω V V mA Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 2: Max/min ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined from tested parameters. Note 3: Differential gain and phase measured at AV+2, Rf500Ω,RL 150Ω 1Vpp equivalent video signal, 0-100 IRE, 40 IREpp, 0IRE = 0 volts, at 75Ω load and 3.58MHz. See text. Note 4: See the text on the back of the datasheet. Note 5: AJ-level: spec. is 100% tested at +25˚C, sample at 85˚C. Ordering Information Package Temperature Range Industrial Part Number Package Marking NSC Drawing 8-pin plastic DIP −40˚C to +85˚C CLC404AJP CLC404AJP N08E 8-pin plastic SOIC −40˚C to +85˚C CLC404AJE CLC404AJE M08A 5-pin SOT −40˚C to +85˚C CLC404AJM5 A16 MA05A 3 www.national.com CLC404 Typical Performance Characteristics Frequency Response AV = +2V/V Frequency Response AV = +6V/V 01274601 01274602 Frequency Response AV = +20V/V Inverting Frequency Response 01274603 01274604 Bandwidth vs Load Capacitance Recommended RS vs Load Capacitance 01274605 01274606 www.national.com 4 CLC404 Typical Performance Characteristics (Continued) Large Signal Pulse Response 2nd Harmonic Dist. vs. Amplitude 01274608 01274607 3rd Harmonic Dist. vs. Amplitude Settling Time 01274609 01274610 2nd Harmonic Distortion CL = 25pF 3rd Harmonic Distortion CL = 25pF 01274611 01274612 5 www.national.com CLC404 Typical Performance Characteristics (Continued) Equivalent Input Noise Differential Gain and Phase vs. Load 01274614 01274613 CMRR and PSRR 01274615 www.national.com 6 CLC404 Application Division 01274616 FIGURE 1. Recommended Non-Inverting Gain Circuit 01274617 FIGURE 2. Recommended Inverting Gain Circuit there is almost no difference between large and small signal performance at this gain. Large signal performance in the CLC404 at a gain of +6 is not slew rate limited. (In an amplifier which is slew limiting, the large signal response rolloff has an abrupt break indicating the onset of slew rate limitation.) The CLC404 reaches slew rate limits only for low non-inverting gains. In other words, slew rate limiting is constrained by common mode voltage swings at the input. (This is different from traditional slew rate constraints.) The large-signal frequency response plot at a gain of +2 shows a break in the response, which shows that slew rate limit has been reached. Note also that the frequency response plots at gain of +21 show that the large signal and small signal responses are nearly identical. Slew Rate Slew rate limiting is a nonlinear response which occurs in amplifiers when the output voltage swing approaches hard, abrupt limits in the speed at which it can change. In most applications, this results in an easily identifiable “slew rate” as well as a dramatic increase in distortion for large signal levels. The CLC404 has been designed to provide enough slew rate to avoid slew rate limiting in almost all circuit configurations. The large signal bandwidth of 165MHz, therefore, is nearly the same as the 175MHz small signal bandwidth. The result is a low-distortion, linear system for both small signals and large signals. Slew rate and large signal performance in the CLC404 can best be understood by first comparing the small and large signal performance plots at a gain of +6. In the CLC404, 7 www.national.com CLC404 previous pages are valid only when a 500Ω feedback resistor is used. Selection of an incorrect value can lead to severe rolloff in frequency-response (if the resistor value is too large) or peaking or oscillation (if the value is too low). Differential Gain and Phase Differential gain and phase are measurements useful primarily in composite video channels. Differential gain and phase are measured by monitoring the gain and phase of a high frequency carrier (3.58MHz for NTSC composite video) as the output of the amplifier is swept over a range of DC voltages. Any changes in gain and phase at the carrier frequency are the desired measurement, differential gain and phase. Specifications for the CLC404 include differential gain and phase. The test signals used are based on a 1VPP video level. Test conditions used are the following. DC sweep range: 0 to 100 IRE units (black to white) Carrier: 3.58MHz at 40 IRE units peak to peak The amplifier is specified for a gain of +2, and 150Ω load (for a backmatched 75Ω system.) IRE amplitudes are referred to 75Ω at the load of a video system. This is a different condition from the rest of the specifications (AV = +6, Rf = 100Ω). Source Impedance For best results, source impedance in the non-inverting circuit configuration (see Figure 1) should be kept below 3kΩ Above 3kΩ it is possible for oscillation to occur, depending on other circuit parasitics. Depending on the signal source, a resistor with a value of less than 3kΩ may be used to terminate the non-inverting input to ground. Feedback Resistor In current-feedback op amps, the value of the feedback resistor plays a major role in determining amplifier dynamics. It is important to select the correct value resistor. The CLC404 provides optimum performance with a 500Ω feedback resistor. Furthermore, the specifications shown on the www.national.com Printed Circuit Layout As with any high frequency device, a good PCB layout will enhance performance. Ground plane construction and good power supply bypassing close to the package are critical to achieving full performance. In the non-inverting configuration, the amplifier is sensitive to stray capacitance to ground at the inverting input. Hence, the inverting node connections should be small with minimal coupling to the ground plane. Shunt capacitance across the feedback resistor should not be used to compensate for this effect. Parasitic or load capacitance directly on the output will introduce additional phase shift in the loop degrading the loop phase margin and leading to frequency response peaking. A small series resistor before the capacitance effectively decouples this effect. The graphs on the preceding page illustrate the required resistor value and resulting performance vs. capacitance. Precision buffed resistors (PRP8351 series from Precision Resistive Products) with low parasitic reactances were used to develop the data sheet specifications. Precision carbon composition resistors will also yield excellent results. Standard spirally-trimmed RN55D metal film resistors will work with a slight decrease in bandwidth due to their reactive nature at high frequencies. Evaluation PC boards (part numbers CLC730013 for through-hole and CLC 730027 for SOIC) for the CLC404 are available. 8 CLC404 Physical Dimensions inches (millimeters) unless otherwise noted NS Product Number M08A NS Product Number MA05A 9 www.national.com CLC404 Wideband, High Slew Rate, Monolithic Op Amp Physical Dimensions inches (millimeters) unless otherwise noted (Continued) NS Product Number N08E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.