CLVTH16245AQDLREP

SN74LVTH16245A-EP 3.3-V ABT 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS www.ti.com FEATURES • • • • • • • • • • • • • • • (1) Controlled Baseline – One Assembly – One Test Site – One Fabrication Site Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product-Change Notification Qualification Pedigree (1) Member of the Texas Instruments Widebus™ Family State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Supports Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC) Supports Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) VCC. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback 3 SN74LVTH16245A-EP 3.3-V ABT 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS www.ti.com SCAS693G – APRIL 2003 – REVISED OCTOBER 2006 Recommended Operating Conditions (1) SN74LVTH16245AQ SN74LVTH16245AM MIN MAX MIN MAX MIN MAX 2.7 3.6 2.7 3.6 2.7 3.6 UNIT VCC Supply voltage VIH High-level input voltage VIL Low-level input voltage 0.8 0.8 0.8 VI Input voltage 5.5 5.5 5.5 V IOH High-level output current –24 –32 –24 mA IOL Low-level output current 24 64 24 mA ∆t/∆v Input transition rise or fall rate 10 10 10 ns/V 2 Outputs enabled ∆t/∆VCC Power-up ramp rate 200 TA –40 (1) 4 SN74LVTH16245AI Operating free-air temperature 2 2 200 125 –40 V –55 V µs/V 200 85 V 125 °C All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. See the TI application report, Implications of Slow or Floating CMOS Inputs (SCBA004). Submit Documentation Feedback SN74LVTH16245A-EP 3.3-V ABT 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS www.ti.com SCAS693G – APRIL 2003 – REVISED OCTOBER 2006 Electrical Characteristics over operating free-air temperature range (unless otherwise noted) PARAMETER VIK SN74LVTH16245AQ TEST CONDITIONS VCC = 2.7 V, MIN TYP (1) II = –18 mA VCC = 2.7 V to 3.6 V, IOH = –100 µA VCC = 2.7 V, VOH VCC = 3.3 V VCC = 2.7 V VOL VCC = 3 V Control inputs II IOH = –8 mA IOH = –24 mA MIN TYP (1) –1.2 –1.2 2.4 2.4 2.4 2 MAX –1.2 VCC – 0.2 IOH = –32 mA 2 IOL = 100 µA 0.2 0.2 0.2 IOL = 24 mA 0.5 0.5 0.5 IOL = 16 mA 0.4 0.4 0.4 IOL = 32 mA 0.5 IOL = 64 mA 0.55 ±1 ±1 ±1 VCC = 0 or 3.6 V, VI = 5.5 V 10 10 10 20 20 20 VCC = 3 V VI = VCC 5 1 5 –5 –5 –5 A or B port ±100 VI = 0.8 V VI = 2 V V V VCC = 3.6 V, VI = VCC or GND VCC = 3.6 V UNIT 2 VCC = 0, VI or VO = 0 to 4.5 V II(hold) (3) MIN TYP (1) VCC – 0.2 VI = 0 Ioff SN74LVTH16245AM MAX VCC – 0.2 VI = 5.5 V A or B port (2) SN74LVTH16245AI MAX 75 75 –75 –75 V µA µA 75 –75 VCC = 3.6 V, VI = 0 to 3.6 V µA 500 –750 IOZPU VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don't care ±100 ±100 ±100 µA IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don't care ±100 ±100 ±100 µA 0.19 0.19 0.19 ICC VCC = 3.6 V, IO = 0, VI = VCC or GND 5 5 5 0.19 0.19 0.19 0.2 0.2 0.2 Outputs high Outputs low Outputs disabled mA ∆ICC (4) VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 4 4 4 pF Cio VO = 3 V or 0 10 10 10 pF (1) (2) (3) (4) mA All typical values are at VCC = 3.3 V, TA = 25°C. Unused pins at VCC or GND This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. Submit Documentation Feedback 5 SN74LVTH16245A-EP 3.3-V ABT 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS www.ti.com SCAS693G – APRIL 2003 – REVISED OCTOBER 2006 Switching Characteristics over operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN74LVTH16245AQ SN74LVTH16245AM PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) A or B TO (OUTPUT) B or A OE A or B OE A or B VCC = 3.3 V ±0.3 V SN74LVTH16245AI 6 VCC = 2.7 V MAX MIN TYP (1) MAX 4.5 4.6 1.5 2.3 3.3 3.7 0.5 4.4 3.9 1.3 2.1 3.3 3.5 0.5 6.5 6.6 1.5 2.8 4.5 5.3 0.5 5.4 6.2 1.6 2.9 4.6 5.2 1 6.8 7 2.3 3.7 5.1 5.5 1 6.2 6.3 2.2 3.5 5.1 5.4 0.5 0.5 MIN MAX 0.5 MIN tsk(o) (1) VCC = 3.3 V ±0.3 V VCC = 2.7 V All typical values are at VCC = 3.3 V, TA = 25°C. Submit Documentation Feedback MIN UNIT MAX ns ns ns ns SN74LVTH16245A-EP 3.3-V ABT 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS www.ti.com SCAS693G – APRIL 2003 – REVISED OCTOBER 2006 PARAMETER MEASUREMENT INFORMATION 6V S1 500 W From Output Under Test Open GND CL = 50 pF (see Note A) 500 W TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT 1.5 V Timing Input 0V tw tsu 2.7 V 1.5 V Input 1.5 V th 2.7 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 2.7 V Input 1.5 V 1.5 V 0V tPHL tPLH V 1.5 V Output 1.5 V V V Output 1.5 V 1.5 V 1.5 V V VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V tPZL Output Waveform 1 S1 at 6 V (see Note B) tPLZ 3V 1.5 V tPZH tPLH tPHL 2.7 V Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V V tPHZ V 1.5 V VOH - 0.3 V »0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 59 W, tr £ 2.5 ns, tf £ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms Submit Documentation Feedback 7 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) (3) Device Marking Samples (4/5) (6) CLVTH16245AMDLREP ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 LVTH16245AEP Samples CLVTH16245AQDGGREP ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 LH16245AEP Samples CLVTH16245AQDLREP ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 LH16245AEP Samples V62/04602-01XE ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 LH16245AEP Samples V62/04602-01YE ACTIVE TSSOP DGG 48 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 125 LH16245AEP Samples V62/04602-03XE ACTIVE SSOP DL 48 1000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 LVTH16245AEP Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of