CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
D
D
D
D
D
D
D
D
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
VCC
O7
D7
D6
O6
O5
D5
D4
O4
CP
CY54FCT374T . . . L PACKAGE
(TOP VIEW)
D1
O1
O2
D2
D3
O7
D
OE
O0
D0
D1
O1
O2
D2
D3
O3
GND
OE
VCC
D
D0
O0
D
CY54FCT374T . . . D PACKAGE
CY74FCT374T . . . P, Q, OR SO PACKAGE
(TOP VIEW)
Function, Pinout, and Drive Compatible
With FCT and F Logic
Reduced VOH (Typically = 3.3 V) Versions
of Equivalent FCT Functions
Edge-Rate Control Circuitry for
Significantly Improved Noise
Characteristics
Ioff Supports Partial-Power-Down Mode
Operation
Matched Rise and Fall Times
Fully Compatible With TTL Input and
Output Logic Levels
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
Edge-Triggered D-Type Inputs
250-MHz Typical Switching Rate
CY54FCT374T
– 32-mA Output Sink Current
– 12-mA Output Source Current
CY74FCT374T
– 64-mA Output Sink Current
– 32-mA Output Source Current
3-State Outputs
4
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
D7
D6
O6
O5
D5
O3
GND
CP
O4
D4
D
description
The ’FCT374T devices are high-speed, low-power, octal D-type flip-flops, featuring separate D-type inputs for
each flip-flop. These devices have 3-state outputs for bus-oriented applications. A buffered clock (CP) and
output-enable (OE) inputs are common to all flip-flops. The eight flip-flops in the ’FCT374T store the state of
their individual D inputs that meet the setup-time and hold-time requirements on the low-to-high CP transition.
When OE is low, the contents of the eight flip-flops are available at the outputs. When OE is high, the outputs
are in the high-impedance state. The state of OE does not affect the state of the flip-flops.
These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the
outputs, preventing damaging current backflow through the device when it is powered down.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
ORDERING INFORMATION
QSOP – Q
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
Tape and reel
5.2
CY74FCT374CTQCT
Tube
5.2
CY74FCT374CTSOC
Tape and reel
5.2
CY74FCT374CTSOCT
DIP – P
Tube
6.5
CY74FCT374ATPC
CY74FCT374ATPC
QSOP – Q
Tape and reel
6.5
CY74FCT374ATQCT
FCT374A
Tube
6.5
CY74FCT374ATSOC
Tape and reel
6.5
CY74FCT374ATSOCT
Tape and reel
10
CY74FCT374TQCT
Tube
10
CY74FCT374TSOC
Tape and reel
10
CY74FCT374TSOCT
CDIP – D
Tube
6.2
CY54FCT374CTDMB
LCC – L
Tube
6.2
CY54FCT374CTLMB
CDIP – D
Tube
7.2
CY54FCT374ATDMB
LCC – L
Tube
7.2
CY54FCT374ATLMB
CDIP – D
Tube
11
CY54FCT374TDMB
LCC – L
Tube
11
SOIC – SO
–40°C
40°C to 85°C
SOIC – SO
QSOP – Q
SOIC – SO
55°C to 125°C
–55°C
SPEED
(ns)
PACKAGE†
TA
FCT374C
FCT374C
FCT374A
FCT374
FCT374
CY54FCT374TLMB
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available
at www.ti.com/sc/package.
FUNCTION TABLE
INPUTS
OE
OUTPUT
O
↑
L
H
↑
L
L
X
H
Z
D
CP
H
L
X
H = High logic level, L = Low logic level,
X = Don’t care, Z = High-impedance state,
↑ = Low-to-high clock transition
logic diagram (positive logic)
OE
CP
1
11
C1
D0
3
1D
Q
To Seven Other Channels
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2
O0
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range to ground potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
DC output current (maximum sink current/pin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mA
Package thermal impedance, θJA (see Note 1): P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W
Q package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68°C/W
SO package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
Ambient temperature range with power applied, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 135°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 2)
CY54FCT374T
CY74FCT374T
MIN
NOM
MAX
MIN
NOM
MAX
4.5
5
5.5
4.75
5
5.25
UNIT
VCC
VIH
Supply voltage
VIL
IOH
Low-level input voltage
0.8
0.8
V
High-level output current
–12
–32
mA
IOL
TA
Low-level output current
32
64
mA
85
°C
High-level input voltage
2
Operating free-air temperature
–55
2
125
–40
V
V
NOTE 2: All unused inputs of the device must be held at VCC or GND to ensure proper device operation.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VOH
CY54FCT374T
TYP†
MAX
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.75 V,
IIN = –18 mA
IIN = –18 mA
VCC = 4.5 V,
IOH = –12 mA
IOH = –32 mA
VCC = 4
4.75
75 V
MIN
–0.7
–1.2
–0.7
2.4
2.4
Vhys
All inputs
II
VCC = 5.5 V,
VCC = 5.25 V,
VIN = VCC
VIN = VCC
5
IIH
VCC = 5.5 V,
VCC = 5.25 V,
VIN = 2.7 V
VIN = 2.7 V
±1
IIL
VCC = 5.5 V,
VCC = 5.25 V,
VIN = 0.5 V
VIN = 0.5 V
±1
VCC = 0 V,
VCC = 5.5 V,
VOUT = 4.5 V
VOUT = 0 V
VCC = 5.25 V,
VCC = 5.5 V,
VOUT = 0 V
VIN = 2.7 V
VCC = 5.25 V,
VCC = 5.5 V,
VIN = 2.7 V
VIN = 0.5 V
VCC = 5.25 V,
VCC = 5.5 V,
VIN = 0.5 V
VIN ≤ 0.2 V,
IOZH
IOZL
ICC
∆ICC
0.3
3.3
0.55
IOL = 64 mA
0.3
0.2
0.55
0.2
±1
±1
±1
–120
±1
–225
–60
–120
–225
10
10
–10
–10
VIN ≥ VCC – 0.2 V
VCC = 5.25 V,
VIN ≤ 0.2 V,
VIN ≥ VCC – 0.2 V
VCC = 5.5 V, VIN = 3.4 V§, f1 = 0, Outputs open
VCC = 5.25 V, VIN = 3.4 V§, f1 = 0, Outputs open
0.1
0.5
V
V
5
–60
V
V
2
IOH = –15 mA
IOL = 32 mA
VCC = 4.5 V,
VCC = 4.75 V,
IOS‡
–1.2
UNIT
3.3
VOL
Ioff
CY74FCT374T
TYP†
MAX
MIN
µA
µA
µA
µA
mA
µA
µA
0.2
0.1
0.2
0.5
2
2
mA
mA
† Typical values are at VCC = 5 V, TA = 25°C.
‡ Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or
sample-and-hold techniques are preferable to minimize internal chip heating and more accurately reflect operational values. Otherwise, prolonged
shorting of a high output can raise the chip temperature well above normal and cause invalid readings in other parametric tests. In any sequence
of parameter tests, IOS tests should be performed last.
§ Per TTL-driven input (VIN = 3.4 V); all other inputs at VCC or GND
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (continued)
PARAMETER
ICCD¶
CY54FCT374T
TYP†
MAX
TEST CONDITIONS
MIN
VCC = 5.5 V, Outputs open,
One bit switching at 50% duty cycle, OE = GND,
VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V
VCC = 5.25 V, Outputs open,
One bit switching at 50% duty cycle, OE = GND,
VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V
VCC = 5.5 V,
f0 = 10 MHz,,
Outputs open,
OE = GND
IC
VCC = 5.25 V,
f0 = 10 MHz,,
Outputs open,
OE = GND
0.06
CY74FCT374T
TYP†
MAX
MIN
UNIT
0.12
mA/
MHz
0.06
0.12
One bit
switching
at f1 = 5 MHz
at 50% duty
cycle
VIN ≤ 0.2 V or
VIN ≥ VCC – 0.2 V
0.7
1.4
VIN = 3.4 V or GND
1.2
3.4
Eight bits
switching
at f1 = 2.5 MHz
at 50% duty
cycle
VIN ≤ 0.2 V or
VIN ≥ VCC – 0.2 V
1.6
3.2||
VIN = 3.4 V or GND
3.9
12.2||
One bit
switching
at f1 = 5 MHz
at 50% duty
cycle
VIN ≤ 0.2 V or
VIN ≥ VCC – 0.2 V
0.7
1.4
VIN = 3.4 V or GND
1.2
3.4
Eight bits
switching
at f1 = 2.5 MHz
at 50% duty
cycle
VIN ≤ 0.2 V or
VIN ≥ VCC – 0.2 V
1.6
3.2||
VIN = 3.4 V or GND
3.9
12.2||
mA
Ci
5
10
5
10
pF
Co
9
12
9
12
pF
† Typical values are at VCC = 5 V, TA = 25°C.
¶ This parameter is derived for use in total power-supply calculations.
# IC
= ICC + ∆ICC × DH × NT + ICCD (f0/2 + f1 × N1)
Where:
IC
= Total supply current
ICC = Power-supply current with CMOS input levels
∆ICC = Power-supply current for a TTL high input (VIN = 3.4 V)
DH
= Duty cycle for TTL inputs high
NT
= Number of TTL inputs at DH
ICCD = Dynamic current caused by an input transition pair (HLH or LHL)
f0
= Clock frequency for registered devices, otherwise zero
f1
= Input signal frequency
N1
= Number of inputs changing at f1
All currents are in milliamperes and all frequencies are in megahertz.
|| Values for these conditions are examples of the ICC formula.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
timing requirements over recommended operating free-air temperature range (unless otherwise
noted) (see Figure 1)
CY54FCT374T
MIN
MAX
CY54FCT374AT
MIN
MAX
CY54FCT374CT
MIN
MAX
UNIT
tw
tsu
Pulse duration, CP high or low
7
6
6
ns
Setup time, data before CP↑
2
2
2
ns
th
Hold time, data after CP↑
1.5
1.5
1.5
ns
timing requirements over recommended operating free-air temperature range (unless otherwise
noted) (see Figure 1)
CY74FCT374T
MIN
MAX
CY74FCT374AT
MIN
MAX
CY74FCT374CT
MIN
MAX
UNIT
tw
tsu
Pulse duration, CP high or low
7
5
5
ns
Setup time, data before CP↑
2
2
2
ns
th
Hold time, data after CP↑
1.5
1.5
1.5
ns
switching characteristics over operating free-air temperature range (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
CP
O
tPZH
tPZL
OE
O
tPHZ
tPLZ
OE
O
CY54FCT374T
CY54FCT374AT
CY54FCT374CT
MIN
MAX
MIN
MAX
MIN
MAX
2
11
2
7.2
2
6.2
2
11
2
7.2
2
6.2
1.5
14
1.5
7.5
1.5
6.2
1.5
14
1.5
7.5
1.5
6.2
1.5
8
1.5
6.5
1.5
5.7
1.5
8
1.5
6.5
1.5
5.7
UNIT
ns
ns
ns
switching characteristics over operating free-air temperature range (see Figure 1)
6
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
CP
O
tPZH
tPZL
OE
O
tPHZ
tPLZ
OE
O
POST OFFICE BOX 655303
CY74FCT374T
CY74FCT374AT
CY74FCT374CT
MIN
MAX
MIN
MAX
MIN
MAX
2
10
2
6.5
2
5.2
2
10
2
6.5
2
5.2
1.5
12.5
1.5
6.5
1.5
5.5
1.5
12.5
1.5
6.5
1.5
5.5
1.5
8
1.5
5.5
1.5
5
1.5
8
1.5
5.5
1.5
5
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
CY54FCT374T, CY74FCT374T
8-BIT REGISTERS
WITH 3-STATE OUTPUTS
SCCS022A – MAY 1994 – REVISED OCTOBER 2001
PARAMETER MEASUREMENT INFORMATION
7V
From Output
Under Test
From Output
Under Test
Test
Point
CL = 50 pF
(see Note A)
Open
TEST
GND
CL = 50 pF
(see Note A)
500 Ω
S1
500 Ω
S1
Open
7V
Open
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
500 Ω
LOAD CIRCUIT FOR
3-STATE OUTPUTS
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
3V
1.5 V
Timing Input
0V
tw
tsu
3V
1.5 V
Input
1.5 V
th
3V
1.5 V
Data Input
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.5 V
Input
1.5 V
0V
tPLH
tPHL
1.5 V
1.5 V
VOL
tPHL
Out-of-Phase
Output
tPLZ
≈3.5 V
1.5 V
tPZH
VOH
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
1.5 V
0V
Output
Waveform 1
(see Note B)
tPLH
1.5 V
1.5 V
tPZL
VOH
In-Phase
Output
3V
Output
Control
Output
Waveform 2
(see Note B)
VOL + 0.3 V
VOL
tPHZ
1.5 V
VOH – 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
(3)
Device Marking
Samples
(4/5)
(6)
5962-9221802M2A
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629221802M2A
CY54FCT
374TLMB
5962-9221802MRA
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9221802MR
A
CY54FCT374TDMB
5962-9221804M2A
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629221804M2A
CY54FCT
374ATLMB
5962-9221804MRA
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9221804MR
A
CY54FCT374ATDM
B
5962-9221806M2A
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629221806M2A
CY54FCT
374CTLMB
5962-9222203M2A
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629222203M2A
CY54FCT
574ATLMB
5962-9222203MRA
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9222203MR
A
Samples
5962-9222205MRA
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9222205MR
A
Samples
CY54FCT374ATDMB
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9221804MR
A
CY54FCT374ATDM
B
CY54FCT374ATLMB
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
Addendum-Page 1
59629221804M2A
CY54FCT
374ATLMB
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
14-Oct-2022
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
CY54FCT374CTLMB
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629221806M2A
CY54FCT
374CTLMB
CY54FCT374TDMB
ACTIVE
CDIP
J
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9221802MR
A
CY54FCT374TDMB
CY54FCT374TLMB
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629221802M2A
CY54FCT
374TLMB
CY54FCT574ATLMB
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629222203M2A
CY54FCT
574ATLMB
CY74FCT374ATPC
ACTIVE
PDIP
N
20
20
RoHS &
Non-Green
NIPDAU
N / A for Pkg Type
-40 to 85
CY74FCT374ATPC
Samples
CY74FCT374ATQCT
ACTIVE
SSOP
DBQ
20
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
FCT374A
Samples
CY74FCT374ATSOC
ACTIVE
SOIC
DW
20
25
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT374A
Samples
CY74FCT374ATSOCT
ACTIVE
SOIC
DW
20
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT374A
Samples
CY74FCT374CTSOC
ACTIVE
SOIC
DW
20
25
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT374C
Samples
CY74FCT374TQCT
ACTIVE
SSOP
DBQ
20
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
FCT374
Samples
CY74FCT374TSOC
ACTIVE
SOIC
DW
20
25
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT374
Samples
CY74FCT574ATQCT
ACTIVE
SSOP
DBQ
20
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
FCT574A
Samples
CY74FCT574ATSOC
ACTIVE
SOIC
DW
20
25
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT574A
Samples
CY74FCT574CTQCT
ACTIVE
SSOP
DBQ
20
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
FCT574C
Samples
CY74FCT574CTSOC
ACTIVE
SOIC
DW
20
25
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
FCT574C
Samples
CY74FCT574TQCT
ACTIVE
SSOP
DBQ
20
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
FCT574
Samples
Addendum-Page 2
Samples
Samples
Samples
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
14-Oct-2022
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
RoHS & Green
NIPDAU
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
CY74FCT574TSOC
ACTIVE
SOIC
DW
20
25
Level-1-260C-UNLIM
-40 to 85
FCT574
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of