Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
DS125BR111 Low Power 12.5 Gbps 1-Lane Linear Repeater
with Equalization
1 Features
3 Description
•
•
•
•
The DS125BR111 is an extremely low power high
performance repeater/redriver designed to support 1lane carrying high speed interface up to 12.5 Gbps.
The receiver's continuous time linear equalizer
(CTLE) provides a boost of 3-10 dB at 6 GHz in each
channel. When operating in SAS-3 or PCIe Gen-3
applications, the DS125BR111 preserves transmit
signal characteristics allowing the host controller and
the end point to negotiate transmit equalizer
coefficients. Transparency to the link training protocol
maximizes the flexibility of the physical placement of
the device within the interconnect and improves
overall channel performance.
1
•
•
•
•
Low 65 mW/Channel (typ) Power Consumption
Supports Link Training
Supports Out-of-Band (OOB) Signaling
Advanced Signal Conditioning I/O
– Receive CTLE up to 10 dB at 6 GHz
– Linear Output Driver
– Output Voltage Range over 1200 mV
Programmable via Pin Selection, EEPROM, or
SMBus Interface
Single Supply Voltage: 2.5 V or 3.3 V
−40°C to 85°C Operating Temperature Range
Flow-thru Pinout in 4 mm × 4 mm 24-pin Leadless
WQFN Package
The programmable settings can be applied easily via
pins, software (SMBus or I2C), or loaded via an
external EEPROM. In EEPROM mode, the
configuration information is automatically loaded on
power up, which eliminates the need for an external
microprocessor or software driver.
2 Applications
•
•
•
SAS-1/2/3 and SATA-1/2/3
PCI Express 1/2/3
Other Proprietary Interfaces up to 12.5 Gbps
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
DS125BR111
WQFN (24)
4.00mm x 4.00mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
DS125BR111
INA+
INA-
OUTA+
OUTAINB+
INB-
OUTB+
OUTBVDD
AD0/EQA0
Address
straps (pull-up
or pull-down)
1 N
AD1/EQA1
ENSMB
AD2/EQB1
SMBus
Slave
Mode(1)
3.3V
AD3/EQB0
4.7 N
4.7 N
RES
SD_TH
VDD
SDA/VODA_DB(2)
SCL/VODB_DB(2)
To system
SMBus
READEN/VOD_SEL
VIN
2.5 V
Mode(4)
VDD_SEL
DONE/RXDET
PWDN(3)
2.5V
10F
(1x)
(1)
(2)
(3)
(4)
(5)
1F
(1x)
0.1F
(2x)
Normal
operation
VDD
(DAP) GND(5)
Schematic requires different connections for SMBus Master Mode and Pin Mode
SMBus signals need to be pulled up elsewhere in the system
PWDN pin can alternatively be driven by a control device (i.e. FPGA)
Schematic requires different connections for 3.3 V mode
A minimum of 4 vias are recommended for proper thermal and electrical performance
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
6
7.1
7.2
7.3
7.4
7.5
7.6
Absolute Maximum Ratings ...................................... 6
Handling Ratings....................................................... 6
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 7
Electrical Characteristics — Serial Management Bus
Interface .................................................................. 10
7.7 Timing Requirements .............................................. 10
7.8 Typical Characteristics ............................................ 12
8
Detailed Description ............................................ 13
8.1 Overview ................................................................. 13
8.2
8.3
8.4
8.5
8.6
9
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Programming ..........................................................
Register Maps .........................................................
13
14
14
17
24
Application and Implementation ........................ 32
9.1 Application Information............................................ 32
9.2 Typical Application ................................................. 34
10 Power Supply Recommendations ..................... 36
11 Layout................................................................... 37
11.1 Layout Guidelines ................................................. 37
11.2 Layout Example .................................................... 37
12 Device and Documentation Support ................. 38
12.1 Trademarks ........................................................... 38
12.2 Electrostatic Discharge Caution ............................ 38
12.3 Glossary ................................................................ 38
13 Mechanical, Packaging, and Orderable
Information ........................................................... 38
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (July 2014) to Revision C
•
Changed data sheet flow and layout to conform with new TI standards. Added the following sections: Application
and Implementation; Power Supply Recommendations; Layout; Device and Documentation Support; Mechanical,
Packaging, and Ordering Information .................................................................................................................................... 1
Changes from Revision A (January 2014) to Revision B
•
2
Page
Changed Features ................................................................................................................................................................. 1
Changes from Original (April 2013) to Revision A
•
Page
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
DS125BR111
www.ti.com
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
6 Pin Configuration and Functions
PWDN
SCL/VODB_DB
SDA/VODA_DB
ENSMB
EQB1/AD2
EQB0/AD3
6
5
4
3
2
1
24 Pin
Package RTW
Top View
OUTA+
7
24
INA+
OUTA-
8
23
INA-
AD1/EQA1
9
22
VDD
AD0/EQA0
10
21
VDD
INB+
11
20
OUTB+
INB-
12
19
OUTB-
13
14
15
16
17
18
RES
SD_TH
VIN
VDD_SEL
VOD_SEL / READEN
RXDET / DONE
SMBUS AND
CONTROL
The center DAP on the package bottom is the only device GND connection. This pad must be connected to
GND through multiple (minimum of 4) vias to ensure optimal electrical and thermal performance.
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
DIFFERENTIAL HIGH SPEED I/O
INB+, INB-
11, 12
I
Inverting and non-inverting CML differential inputs to the equalizer. On-chip 50 Ω termination
resistor connects INB+ to VDD and INB- to VDD when enabled by RXDET control logic.
AC coupling required on high-speed I/O
OUTB+,
OUTB-
20, 19
O
Inverting and non-inverting 50 Ω driver outputs. Compatible with AC coupled CML inputs.
AC coupling required on high-speed I/O
INA+, INA-
24, 23
I
Inverting and non-inverting CML differential inputs to the equalizer. On-chip 50 Ω termination
resistor connects INA+ to VDD and INA- to VDD when enabled by RXDET control logic.
AC coupling required on high-speed I/O
7, 8
O
Inverting and non-inverting 50 Ω driver outputs. Compatible with AC coupled CML inputs.
AC coupling required on high-speed I/O
OUTA+,
OUTA-
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
3
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
www.ti.com
Pin Functions (continued)
PIN
NAME
NO.
I/O
DESCRIPTION
CONTROL PINS — SHARED (LVCMOS)
ENSMB
3
I, 4-LEVEL,
LVCMOS
System Management Bus (SMBus) enable Pin
Tie 1 kΩ to VDD = Register Access SMBus Slave mode
FLOAT = Read External EEPROM (Master SMBus Mode)
Tie 1 kΩ to GND = Pin Mode
ENSMB = Float or 1 (SMBus MODEs)
SCL
SDA
AD0-AD3
5
I, LVCMOS,
O, OPEN
Drain
ENSMB Master or Slave mode
SMBus clock input Pin is enabled (slave mode).
Clock output when loading EEPROM configuration (master mode).
4
I, LVCMOS,
O, OPEN
Drain
ENSMB Master or Slave mode
The SMBus bidirectional SDA Pin is enabled. Data input or open drain output. External pullup required as per SMBus protocol (typically in the 2 kΩ to 5 kΩ range). This pin is 3.3 Vtolerant.
10, 9, 2, 1
I, LVCMOS
ENSMB Master or Slave mode
SMBus Slave Address Inputs. In SMBus mode, these Pins are the user set SMBus slave
address inputs.
READEN
17
I, LVCMOS
ENSMB = Float: When using an External EEPROM, a logic low on this pin starts the load
from the external EEPROM
ENSMB = 1: When using SMBus Slave Mode the VOD_SEL/READEN pin must be tied Low
for the AD[3:0] to be active. If this pin is tied High or Floated an address of 0xB0 will be used
for the DS125BR111.
DONE
18
O, LVCMOS
When using an External EEPROM (ENSMB = Float), Valid Register Load Status Output
HIGH = External EEPROM load failed or incomplete
LOW = External EEPROM load passed
ENSMB = 0 (PIN MODE)
EQA0
EQB0
10
1
I, 4-LEVEL,
LVCMOS
EQA0 and EQB0 control the level of equalization of the A/B directions. The Pins are defined
as EQx0 only when ENSMB is de-asserted (low). When ENSMB goes high the SMBus
registers provide independent control of each channel. See Table 4.
EQA1
EQB1
9
2
I, 4-LEVEL,
LVCMOS
EQA1 and EQB1 are not used in the DS125BR111 design. These pins should always be tied
to GND.
VODA_DB
4
I, 4-LEVEL,
LVCMOS
VODA_DB controls the CHA output amplitude dynamic range, for SAS and PCIe applications
it should be held Low. The Pin is defined as VODA_DB only when ENSMB is de-asserted
(low). When ENSMB goes high the SMBus registers provide control of each channel, pin 4 is
converted to SDA. See Table 5.
VODB_DB
5
I, 4-LEVEL,
LVCMOS
VODB_DB controls the CHB output amplitude dynamic range, for SAS and PCIe applications
it should be held Low. The Pin is defined as VODB_DB only when ENSMB is de-asserted
(low). When ENSMB goes high the SMBus registers provide control of each channel, pin 5 is
converted to SCL. See Table 5.
SD_TH
14
I, 4-LEVEL,
LVCMOS
Controls the internal Signal Detect Threshold. This detection threshold is for system debug
only and does not control the high speed datapath.
See Table 3.
VOD_SEL
17
I, 4-LEVEL,
LVCMOS
VOD_SEL controls the low frequency ratio of input voltage to output voltage amplitude. See
Table 5.
I, 4-LEVEL,
LVCMOS
The RXDET Pin controls the receiver detect function. Depending on the input level, a 50 Ω or
> 50 kΩ termination to the power rail is enabled. In a SAS/SATA system RXDET should be
set to a Logic "1" state to keep the termination always enabled.
The RXDET pin only controls the RXDET function in PIN MODE. PCIe applications
which require SMBus Mode functionality must utilize a specific register write
sequence documented in PCIe Applications . If this sequence is not utilized, SMBus
configuration modes will default the input terminations to active (50 Ω). See Table 2 .
RXDET
4
18
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
DS125BR111
www.ti.com
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
Pin Functions (continued)
PIN
NAME
NO.
I/O
DESCRIPTION
CONTROL PINS — BOTH PIN AND SMBus MODES (LVCMOS)
RES
13
I, 4-LEVEL,
LVCMOS
VDD_SEL
16
I, FLOAT
PWDN
6
I, LVCMOS
Reserved:
This input must be left Floating.
Controls the internal regulator
Float = 2.5 V mode
Tie GND = 3.3 V mode
Tie High = Low power - power down
Tie GND = Normal Operation
See Table 2.
POWER (See Figure 11)
VIN
15
Power
In 3.3 V mode, feed 3.3 V to VIN
In 2.5 V mode, leave floating.
VDD
21, 22
Power
Power supply pins CML/analog
2.5 V mode, connect to 2.5 V
3.3 V mode, decouple each VDD pin with 0.22 µF cap to GND
GND
DAP
Power
Ground pad (DAP - die attach pad).
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
5
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
MIN
MAX
UNIT
Supply Voltage (VDD - 2.5 V)
-0.5
+2.75
V
Supply Voltage (VIN - 3.3 V)
-0.5
+4.0
V
LVCMOS Input/Output Voltage
-0.5
+4.0
V
CML Input Voltage
-0.5
VDD + 0.5
V
CML Input Current
-30
+30
mA
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 Handling Ratings
Tstg
Storage temperature range
Tsolder
Lead Temperature Range Soldering (4 sec.) (1)
V(ESD)
(1)
(2)
(3)
Electrostatic discharge
MIN
MAX
UNIT
-40
125
°C
260
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (2)
-5000
5000
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins (3)
-1250
1250
V
For soldering specifications: See application note SNOA549.
JEDEC document JEP155 states that 500 V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250 V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Supply Voltage (2.5 V mode)
2.375
2.5
2.625
V
Supply Voltage (3.3 V mode)
3.0
3.3
3.6
V
Ambient Temperature
-40
25
+85
°C
SMBus (SDA, SCL)
3.6
V
Supply Noise up to 50 MHz (1)
100
mVp-p
(1)
Allowed supply noise (mVp-p sine wave) under typical conditions.
7.4 Thermal Information
DS125BR111
THERMAL METRIC (1)
RTW
UNIT
24 PINS
RθJA
Junction-to-ambient thermal resistance
35.0
RθJC(top)
Junction-to-case (top) thermal resistance
34.0
RθJB
Junction-to-board thermal resistance
13.4
ψJT
Junction-to-top characterization parameter
0.3
ψJB
Junction-to-board characterization parameter
13.4
RθJC(bot)
Junction-to-case (bottom) thermal resistance
3.3
(1)
6
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
DS125BR111
www.ti.com
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
7.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
40
60
mA
7
13
mA
2.5
2.625
V
POWER
IDD
VDD
Current Consumption
VODx_DB = 0, EQ = 0,
VOD_SEL = 1,
RXDET = 1, PWDN = 0
VIN = 2.625 or 3.6 V
Power Down Current Consumption
PWDN = 1
Integrated LDO Regulator
VIN = 3.0 - 3.6 V
2.375
LVCMOS / LVTTL DC SPECIFICATIONS
Vih25
High Level Input Voltage
2.5 V Supply Mode
1.7
VDD
V
Vih33
High Level Input Voltage
3.3 V Supply Mode
1.7
VIN
V
Vil
Low Level Input Voltage
0
0.7
V
Voh
High Level Output Voltage
(DONE pin)
Ioh = −4 mA
Vol
Low Level Output Voltage
(DONE pin)
Iol = 4 mA
Iih
Input High Current (PWDN pin)
VIN = 3.6 V,
LVCMOS = 3.6 V
Iil
Input Low Current (PWDN pin)
2.0
V
0.4
V
-15
+15
µA
VIN = 3.6 V,
LVCMOS = 0 V
-15
+15
µA
Input High Current with internal
resistors
(4–level input pin)
VIN = 3.6 V,
LVCMOS = 3.6 V
+20
+80
µA
Input Low Current with internal
resistors
(4–level input pin)
VIN = 3.6 V,
LVCMOS = 0 V
-160
-40
µA
4-LEVEL INPUT DC SPECIFICATIONS
Iih
Iil
Vth
Threshold 0 / R
0.40
VDD = 2.5 V (2.5 V supply mode)
Internal LDO Disabled
See Table 1 for details
Threshold R / Float
Threshold Float / 1
Threshold 0 / R
1.25
0.55
VIN = 3.3 V (3.3 V supply mode)
Internal LDO Enabled
See Table 1 for details.
Threshold R / Float
Threshold Float / 1
V
2.1
1.65
V
2.7
CML RECEIVER INPUTS (IN_n+, IN_n-)
RLRX-diff
RX Differential return loss
SDD11 10 MHz
-19
SDD11 2 GHz
-14
SDD11 6-11.1 GHz
-8
dB
RLRX-cm
RX Common mode return loss
0.05 - 5 GHz
ZRX-dc
RX DC common mode impedance
Tested at VDD = 2.5 V
40
50
60
Ω
ZRX-diff-dc
RX DC differential mode impedance
Tested at VDD = 2.5 V
80
100
120
Ω
VRX-signal-det-diff-
Signal detect assert level
SD_TH = F (float),
0101 pattern at 12 Gbps
50
mVp-p
Signal detect de-assert level
SD_TH = F (float),
0101 pattern at 12 Gbps
37
mVp-p
20% to 80% of differential output
voltage
40
ps
20% to 80% of differential output
voltage
0.01
UI
pp
VRX-idle-det-diff-pp
-10
dB
HIGH SPEED OUTPUTS
TTX-RISE-FALL
Transmitter rise/fall time
TRF-MISMATCH
Transmitter rise/fall mismatch
(1)
(2)
(1)
(2)
Rise / Fall time measurements will vary based on EQ setting, Input Amplitude, and input edge rate.
Mismatch between rise time and fall time for a given channel.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
7
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
www.ti.com
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
RLTX-DIFF
TX Differential return loss
RLTX-CM
TX Common mode return loss
ZTX-DIFF-DC
DC differential TX impedance
MIN
TYP
MAX
UNIT
SDD22 10 MHz - 2 GHz
-15
SDD22 5.5 GHz
-12
SDD22 11.1 GHz
-10
dB
0.05 - 5 GHz
-10
dB
100
Ω
20
mA
ITX-SHORT
Transmitter short circuit current limit
VTX-CM-DC-
Absolute delta of DC common mode
voltage during L0 and electrical idle
100
mV
Absolute delta of DC common mode
voltage between TX+ and TX-
25
mV
ACTIVE-IDLE-DELTA
VTX-CM-DC-LINEDELTA
Total current, output shorted to
VDD or GND
dB
HIGH SPEED OUTPUTS
VTX-diff1-pp
Output Voltage Differential Swing
Differential measurement with
OUTx+ and OUTx-,
AC-Coupled and terminated by
50 Ω to GND,
Inputs AC-Coupled,
VODx_DB = 0 dB,
VID = 600 mVp-p
VOD = 001'b (0.7*VID)
440
500
550
mVp-p
Output Voltage Differential Swing
Differential measurement with
OUTx+ and OUTx-,
AC-Coupled and terminated by
50 Ω to GND,
Inputs AC-Coupled,
VODx_DB = 0 dB,
VID = 1000 mVp-p
VOD = 001'b (0.7*VID) (3)
630
700
740
mVp-p
Output Voltage Differential Swing
Differential measurement with
OUTx+ and OUTx-,
AC-Coupled and terminated by
50 Ω to GND,
Inputs AC-Coupled,
VODx_DB = 0 dB,
VID = 600 mVp-p
VOD = 111'b (1.05*VID) (3)
570
650
740
mVp-p
Output Voltage Differential Swing
Differential measurement with
OUTx+ and OUTx-,
AC-Coupled and terminated by
50 Ω to GND,
Inputs AC-Coupled,
VODx_DB = 0 dB,
VID = 1000 mVp-p
VOD = 111'b (1.05*VID) (3)
800
1010
1215
mVp-p
TTX-IDLE-DATA
Time to transition to valid differential
signal after idle
VID = 1.0 Vp-p, 3 Gbps
0.04
ns
TTX-DATA-IDLE
Time to transition to idle after
differential signal
VID = 1.0 Vp-p, 3 Gbps
0.70
ns
TPD
Differential Propagation Delay
EQ = Level 1 to Level 4
70
ps
VTX-diff2-pp
VTX-diff3-pp
VTX-diff4-pp
(3)
8
The output VOD level is not fixed. It will be adjusted automatically based on the VID input amplitude level and the frequency content.
The DS125BR111 repeater is designed to be transparent, so the TX-FIR (de-emphasis) is passed to the RX to support handshake
negotiation link training.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
DS125BR111
www.ti.com
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
EQUALIZATION
DJE1
Residual Deterministic Jitter at 6 Gbps
Input: 5” Differential Stripline,
5mil trace width, FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 0x01,
VOD = 111'b, VODx_DB = 0 dB
0.06
UI
DJE2
Residual Deterministic Jitter at 12 Gbps Input: 5” Differential Stripline,
5mil trace width, FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 0x01,
VOD = 111'b, VODx_DB = 0 dB
0.12
UI
RJADD1
Additive Random Jitter
(4)
Evaluation Module (EVM) only,
FR4,
VID = 0.8 Vp-p,
PRBS7, EQ = 0x00,
VOD = 111'b, VODx_DB = 0 dB
< 300
fs RMS
RJADD2
Additive Random Jitter
(4)
Input: 10" Differential Stripline,
5 mil trace width, FR4,
VID = 0.8 Vp-p,
PRBS7, EQ = 0x03,
VOD = 111'b, VODx_DB = 0 dB
< 400
fs RMS
(4)
Additive random jitter is given in RMS value by the following equation: RJADD = √[(Output Jitter)2 - (Input Jitter)2] . The typical source
input jitter for these measurements is 150 fs RMS.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: DS125BR111
9
DS125BR111
SNLS430C – OCTOBER 2012 – REVISED AUGUST 2014
www.ti.com
7.6 Electrical Characteristics — Serial Management Bus Interface
Over recommended operating supply and temperature ranges unless other specified.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SERIAL BUS INTERFACE DC SPECIFICATIONS
VIL
Data, Clock Input Low Voltage
VIH
Data, Clock Input High Voltage
VOL
Output Low Voltage
VDD
Nominal Bus Voltage
IIH-pin
Input Leakage Per Device pin
IIL-pin
Input Leakage Per Device pin
SDA or SCL, IOL = 1.25 mA
0.8
V
2.1
3.6
V
0
0.36
V
2.375
3.6
V
+20
+150
µA
-160
-40
µA
(1) (2)
CI
Capacitance for SDA and SCL
See