DSD1792ADBR

'!! !0 !,'&$% !" (/#% %$!'"($%

 SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006      

 
 
    FEATURES D Supports Both DSD and PCM Formats D 24-Bit Resolution D Analog Performance: − Dynamic Range: − 132 dB (9 V rms, Mono) − 129 dB (4.5 V rms, Stereo) − 127 dB (2 V rms, Stereo) − THD+N: 0.0004% D Differential Current Output: 7.8 mA p-p D 8× Oversampling Digital Filter: − Stop-Band Attenuation: –130 dB − Pass-Band Ripple: ±0.00001 dB D Sampling Frequency: 10 kHz to 200 kHz D System Clock: 128, 192, 256, 384, 512, or 768 fS With Autodetect D Accepts 16-, 20-, and 24-Bit Audio Data D PCM Data Formats: Standard, I2S, and Left-Justified D Optional Interface to External Digital Filter or DSP Available D TDMCA Interface Available D User-Programmable Mode Controls: − Digital Attenuation: 0 dB to –120 dB, 0.5 dB/Step − Digital De-Emphasis − Digital Filter Rolloff: Sharp or Slow − Soft Mute D Dual Supply Operation: D 5-V Tolerant Digital Inputs D Small 28-Lead SSOP Package APPLICATIONS D A/V Receivers D SACD Player D DVD Players D HDTV Receivers D Car Audio Systems D Digital Multi-Track Recorders D Other Applications Requiring 24-Bit Audio DESCRIPTION The DSD1792A is a monolithic CMOS integrated circuit that includes stereo digital-to-analog converters and support circuitry in a small 28-lead SSOP package. The data converters use TI’s advanced-segment DAC architecture to achieve excellent dynamic performance and improved tolerance to clock jitter. The DSD1792A provides balanced current outputs, allowing the user to optimize analog performance externally. The DSD1792A accepts the PCM and DSD audio data formats, providing easy interfacing to audio DSP and decoder chips. The DSD1792A also interfaces with external digital filter devices (DF1704, DF1706, PMD200). Sampling rates up to 200 kHz are supported. A full set of user-programmable functions is accessible through a 4-wire serial control port, which supports register write and readback functions. The DSD1792A also supports the time-division-multiplexed command and audio (TDMCA) data format. − 5-V Analog, 3.3-V Digital This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. 

 !"#$ % &'!!($ #%  )'*+&#$ ,#$(- !,'&$% &!" $ %)(&&#$% )(! $.( $(!"%  (/#% %$!'"($% %$#,#!, 0#!!#$1!,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2  #++ )#!#"($(!%- Copyright  2006, Texas Instruments Incorporated 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ORDERING INFORMATION PRODUCT PACKAGE PACKAGE CODE OPERATION TEMPERATURE RANGE PACKAGE MARKING DSD1792ADB 28-lead SSOP 28DB –25°C to 85°C DSD1792A ORDERING NUMBER TRANSPORT MEDIA DSD1792ADB Tube DSD1792ADBR Tape and reel ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) DSD1792A VCC1, VCC2L, VCC2R VDD Supply voltage –0.3 V to 6.5 V –0.3 V to 4 V ±0.1 V Supply voltage differences: VCC1, VCC2L and VCC2R ±0.1 V Ground voltage differences: AGND1, AGND2, AGND3L, AGND3R and DGND PLRCK, PDATA, PBCK, SCK, RST, MS(2), MDI, MC, DSDL(2), DSDR(2), DBCK Digital input voltage DSDL(3), DSDR(3), MS(3), MDO –0.3 V to 6.5 V –0.3 V to (VDD + 0.3 V) < 4 V –0.3 V to (VCC + 0.3 V) < 6.5 V Analog input voltage ±10 mA Input current (any pins except supplies) Ambient temperature under bias –40°C to 125°C Storage temperature –55°C to 150°C Junction temperature 150°C Lead temperature (soldering) 260°C, 5 s Package temperature (IR reflow, peak) 250°C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) Input mode (3) Output mode ELECTRICAL CHARACTERISTICS all specifications at TA = 25°C, VCC1 = VCC2L = VCC2R = 5 V, fS = 44.1 kHz, system clock = 256 fS, and 24-bit data unless otherwise noted DSD1792ADB PARAMETER TEST CONDITIONS MIN RESOLUTION TYP MAX 24 UNIT Bits DATA FORMAT (PCM Mode) fS Audio data interface format Standard, I2S, left justified Audio data bit length 16-, 20-, 24-bit selectable Audio data format MSB first, 2s complement Sampling frequency System clock frequency 10 200 kHz 128, 192, 256, 384, 512, 768 fS DATA FORMAT (DSD Mode) Audio data interface format fS 1 Bit Sampling frequency 2.8224 System clock frequency 2 DSD (direct stream digital) Audio data bit length 2.8224 MHz 11.2896 MHz 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ELECTRICAL CHARACTERISTICS (Continued) all specifications at TA = 25°C, VCC1 = VCC2L = VCC2R = 5 V, fS = 44.1 kHz, system clock = 256 fS, and 24-bit data unless otherwise noted DSD1792ADB PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DIGITAL INPUT/OUTPUT Logic family TTL compatible VIH VIL 2 Input logic level IIH IIL Input logic current VIN = VDD VIN = 0 V VOH VOL Output logic level IOH = –2 mA IOL = 2 mA 0.8 10 –10 2.4 0.4 IOHZ High-impedance output logic current(1) IOLZ VOUT = VDD VOUT = 0 V DYNAMIC PERFORMANCE (PCM MODE, 2-V RMS OUTPUT) (2)(3) THD+N at VOUT = 0 dB fS = 44.1 kHz fS = 96 kHz fS = 192 kHz EIAJ, A-weighted, fS = 44.1 kHz Dynamic range Channel separation Dynamic range Signal-to-noise ratio Channel separation Vdc µA 0.0008% 0.0015% 123 127 127 127 123 127 EIAJ, A-weighted, fS = 192 kHz 127 120 dB 127 EIAJ, A-weighted, fS = 96 kHz fS = 44.1 kHz fS = 96 kHz µA 0.0008% EIAJ, A-weighted, fS = 192 kHz fS = 192 kHz Level Linearity Error VOUT = –120 dB DYNAMIC PERFORMANCE (PCM Mode, 4.5-V RMS Output) (2)(4) THD+N at VOUT = 0 dB 0.0004% EIAJ, A-weighted, fS = 96 kHz EIAJ, A-weighted, fS = 44.1 kHz Signal-to-noise ratio 10 –10 Vdc dB 123 122 dB 120 ±1 fS = 44.1 kHz fS = 96 kHz 0.0004% fS = 192 kHz EIAJ, A-weighted, fS = 44.1 kHz 0.0015% dB 0.0008% 129 EIAJ, A-weighted, fS = 96 kHz 129 EIAJ, A-weighted, fS = 192 kHz 129 EIAJ, A-weighted, fS = 44.1 kHz 129 EIAJ, A-weighted, fS = 96 kHz 129 EIAJ, A-weighted, fS = 192 kHz 129 fS = 44.1 kHz fS = 96 kHz 124 fS = 192 kHz 121 123 dB dB dB (1) Pin 13 (MDO) (2) Filter condition: THD+N: 20-Hz HPF, 20-kHz apogee LPF Dynamic range: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted Signal-to-noise ratio: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted Channel separation: 20-Hz HPF, 20-kHz AES17 LPF Analog performance specifications are measured using the System Two Cascade audio measurement system by Audio Precision in the averaging mode. (3) Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 33. (4) Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 34. Audio Precision and System Two are trademarks of Audio Precision, Inc. Other trademarks are the property of their respective owners. 3 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ELECTRICAL CHARACTERISTICS (Continued) all specifications at TA = 25°C, VCC1 = VCC2L = VCC2R = 5 V, fS = 44.1 kHz, system clock = 256 fS, and 24-bit data unless otherwise noted DSD1792ADB PARAMETER TEST CONDITIONS MIN TYP UNIT MAX DYNAMIC PERFORMANCE (MONO MODE) (1)(2) THD+N at VOUT = 0 dB Dynamic range Signal-to-noise ratio fS = 44.1 kHz fS = 96 kHz 0.0004% fS = 192 kHz EIAJ, A-weighted, fS = 44.1 kHz 0.0015% 0.0008% 132 EIAJ, A-weighted, fS = 96 kHz 132 EIAJ, A-weighted, fS = 192 kHz 132 EIAJ, A-weighted, fS = 44.1 kHz 132 EIAJ, A-weighted, fS = 96 kHz 132 EIAJ, A-weighted, fS = 192 kHz 132 dB dB DSD MODE DYNAMIC PERFORMANCE (1) (3) (44.1 kHz, 64 fS) THD+N at FS 4.5 V rms Dynamic range –60 dB, EIAJ, A-weighted 0.0005% 128 dB Signal-to-noise ratio EIAJ, A-weighted 128 dB ANALOG OUTPUT Gain error Gain mismatch, channel-to-channel Bipolar zero error At BPZ Output current Full scale (0 dB) Center current At BPZ –6 ±2 6 % of FSR –3 ±0.5 3 % of FSR –2 ±0.5 2 % of FSR 7.8 mA p-p –6.2 mA DIGITAL FILTER PERFORMANCE ±0.004 De-emphasis error dB FILTER CHARACTERISTICS-1: SHARP ROLLOFF Pass band ±0.00001 dB 0.454 fS –3 dB Stop band 0.49 fS 0.546 fS ±0.00001 Pass-band ripple Stop-band attenuation Stop band = 0.546 fS –130 Delay time dB dB 55/fS s FILTER CHARACTERISTICS-2: SLOW ROLLOFF Pass band ±0.04 dB 0.254 fS –3 dB Stop band 0.46 fS 0.732 fS ±0.001 Pass-band ripple Stop-band attenuation Delay time Stop band = 0.732 fS –100 dB dB s (1) Filter condition: THD+N: 20-Hz HPF, 20-kHz apogee LPF Dynamic range: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted Signal-to-noise ratio: 20-Hz HPF, 20-kHz AES17 LPF, A-weighted Channel separation: 20-Hz HPF, 20-kHz AES17 LPF Analog performance specifications are measured using the System Two Cascade audio measurement system by Audio Precision in the averaging mode. (2) Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 34. (3) Dynamic performance and dc accuracy are specified at the output of the postamplifier as shown in Figure 35. 4 18/fS 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ELECTRICAL CHARACTERISTICS (Continued) all specifications at TA = 25°C, VCC1 = VCC2L = VCC2R = 5 V, fS = 44.1 kHz, system clock = 256 fS, and 24-bit data unless otherwise noted DSD1792ADB PARAMETER TEST CONDITIONS MIN TYP MAX UNIT POWER SUPPLY REQUIREMENTS VDD VCC1 VCC2L 3 3.3 3.6 Vdc 4.75 5 5.25 Vdc fS = 44.1 kHz fS = 96 kHz 12 15 fS = 192 kHz fS = 44.1 kHz 45 fS = 96 kHz fS = 192 kHz 35 fS = 44.1 kHz fS = 96 kHz 205 fS = 192 kHz 335 Voltage range VCC2R IDD Supply current (1) ICC Power dissipation (1) 23 33 mA 40 mA 37 250 250 mW TEMPERATURE RANGE Operation temperature –25 θJA Thermal resistance (1) Input is BPZ data. 28-pin SSOP 85 100 °C °C/W PIN ASSIGNMENTS DSD1792A (TOP VIEW) DSDL DSDR DBCK PLRCK PDATA PBCK SCK DGND VDD MS MDI MC MDO RST 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC2L AGND3L IOUTL– IOUTL+ AGND2 VCC1 VCOML VCOMR IREF AGND1 IOUTR– IOUTR+ AGND3R VCC2R 5 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Terminal Functions TERMINAL NAME PIN I/O DESCRIPTIONS AGND1 19 – Analog ground (internal bias) AGND2 24 – Analog ground (internal bias) AGND3L 27 – Analog ground (L-channel DACFF) AGND3R 16 – DBCK 3 I Analog ground (R-channel DACFF) Bit clock input for DSD modes (1) DGND 8 – Digital ground DSDL 1 I/O L-channel audio data input when in DSD and external DF modes PCM-mode zero flag for L-channel when in zero-flag output mode(2) DSDR 2 I/O R-channel audio data input when in DSD and external DF modes PCM-mode zero flag for R-channel when in zero-flag output mode (2) IOUTL+ IOUTL– 25 O L-channel analog current output + 26 O L-channel analog current output – IOUTR+ IOUTR– 17 O R-channel analog current output + 18 O R-channel analog current output – IREF MC 20 – 12 I Output current reference bias pin Mode control clock input(1) MDI 11 I Mode control data input (1) MDO 13 O MS 10 I/O Mode control readback data output (3) Mode control chip-select input(2) PBCK 6 I PDATA 5 I PLRCK 4 I RST 14 I Left and right clock (fS) input for PCM-format operation. WDCK clock input for external DF mode. Connected to GND for DSD mode (1) Reset(1) SCK 7 I System clock input (1) VCC1 VCC2L 23 – Analog power supply, 5 V 28 – Analog power supply (L-channel DACFF), 5 V VCC2R VCOML 15 – Analog power supply (R-channel DACFF), 5 V 22 – L-channel internal bias decoupling pin Bit clock input. Connected to GND in DSD mode (1) Serial audio data input for PCM-format operation (1) VCOMR 21 – R-channel internal bias decoupling pin VDD 9 – Digital power supply, 3.3 V (1) Schmitt-trigger input, 5-V tolerant (2) Schmitt-trigger input and output. 5-V tolerant input, and CMOS output (3) 3-state output 6 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 FUNCTIONAL BLOCK DIAGRAM IOUTL– DBCK DSDL DSDR PLRCK Current Segment DAC Audio Data Input I/F IOUTL+ 8 Oversampling Digital Filter and Function Control PBCK PDATA RST VCOML Advanced Segment DAC Modulator Bias and Vref MDO IREF VCOMR Current Segment DAC MS VOUTR IOUTR+ I/V and Filter VCC1 AGND3R AGND3L AGND1 VDD DGND SCK AGND2 Power Supply System Clock Manager VCC2R MC I/V and Filter IOUTR– Function Control I/F VCC2L MDI VOUTL 7 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 TYPICAL PERFORMANCE CURVES DIGITAL FILTER Digital Filter Response AMPLITUDE vs FREQUENCY 0 2 0.00002 −50 1 0.00001 −100 Amplitude – dB Amplitude – dB AMPLITUDE vs FREQUENCY −150 −1 –0.00001 −200 0 1 2 3 4 0 −2 –0.00002 0.0 0.1 Frequency [× fS] 0.2 0.3 0.4 0.5 Frequency [× fS] Figure 1. Frequency Response, Sharp Rolloff Figure 2. Pass-Band Ripple, Sharp Rolloff AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 0 −2 −4 −50 Amplitude – dB Amplitude – dB −6 −100 −8 −10 −12 −14 −150 −16 −18 −200 0 1 2 3 4 Frequency [× fS] Figure 3. Frequency Response, Slow Rolloff 8 −20 0.0 0.1 0.2 0.3 0.4 0.5 0.6 Frequency [× fS] Figure 4. Transition Characteristics, Slow Rolloff 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 De-Emphasis Filter DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 0 20 0.020 fS = 32 kHz fS = 32 kHz 15 0.015 De-Emphasis Error – dB De-Emphasis Level – dB −2 −4 −6 10 0.010 5 0.005 0 −5 –0.005 −10 –0.010 −8 −15 –0.015 −10 −20 –0.020 0 2 4 6 8 10 12 14 0 2 4 6 f – Frequency – kHz 8 10 12 14 f – Frequency – kHz Figure 5 Figure 6 DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 0 20 0.020 fS = 44.1 kHz fS = 44.1 kHz 15 0.015 De-Emphasis Error – dB De-Emphasis Level – dB −2 −4 −6 10 0.010 5 0.005 0 −5 –0.005 −10 –0.010 −8 −15 –0.015 −10 −20 –0.020 0 2 4 6 8 10 12 14 f – Frequency – kHz Figure 7 16 18 20 0 2 4 6 8 10 12 14 16 18 20 f – Frequency – kHz Figure 8 9 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 De-Emphasis Filter (Continued) DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 0 20 0.020 fS = 48 kHz fS = 48 kHz 15 0.015 De-Emphasis Error – dB De-Emphasis Level – dB −2 −4 −6 10 0.010 5 0.005 0 −5 –0.005 −10 –0.010 −8 −15 –0.015 −10 −20 –0.020 0 2 4 6 8 10 12 14 f – Frequency – kHz Figure 9 10 16 18 20 22 0 2 4 6 8 10 12 14 f – Frequency – kHz Figure 10 16 18 20 22 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ANALOG DYNAMIC PERFORMANCE Supply Voltage Characteristics TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE DYNAMIC RANGE vs SUPPLY VOLTAGE 132 130 fS = 96 kHz Dynamic Range – dB THD+N – Total Harmonic Distortion + Noise – % 0.01 fS = 192 kHz 0.001 fS = 96 kHz fS = 48 kHz 128 fS = 192 kHz 126 124 fS = 48 kHz 0.0001 4.50 4.75 5.00 5.25 122 4.50 5.50 VCC – Supply Voltage – V 4.75 Figure 11 130 130 128 Channel Separation – dB SNR – Signal-to-Noise Ratio – dB 5.50 CHANNEL SEPARATION vs SUPPLY VOLTAGE 132 fS = 96 kHz fS = 192 kHz fS = 48 kHz 126 124 122 4.50 5.25 Figure 12 SIGNAL-to-NOISE RATIO vs SUPPLY VOLTAGE 128 5.00 VCC – Supply Voltage – V 126 124 fS = 96 kHz fS = 48 kHz fS = 192 kHz 122 4.75 5.00 5.25 VCC – Supply Voltage – V 5.50 120 4.50 4.75 5.00 5.25 5.50 VCC – Supply Voltage – V Figure 13 Figure 14 NOTE: PCM mode, TA = 25°C, VDD = 3.3 V, measurement circuit is Figure 34 (VOUT = 4.5 V rms). 11 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Temperature Characteristics TOTAL HARMONIC DISTORTION + NOISE vs FREE-AIR TEMPERATURE DYNAMIC RANGE vs FREE-AIR TEMPERATURE 132 130 Dynamic Range – dB THD+N – Total Harmonic Distortion + Noise – % 0.01 fS = 192 kHz 0.001 fS = 96 kHz 128 fS = 96 kHz fS = 48 kHz 126 124 fS = 48 kHz 0.0001 −50 −25 0 25 50 75 122 −50 100 TA – Free-Air Temperature – °C −25 0 75 100 CHANNEL SEPARATION vs FREE-AIR TEMPERATURE 132 130 130 128 fS = 96 kHz Channel Separation – dB SNR – Signal-to-Noise Ratio – dB 50 Figure 16 SIGNAL-to-NOISE RATIO vs FREE-AIR TEMPERATURE 128 fS = 192 kHz fS = 48 kHz 126 124 122 −50 25 TA – Free-Air Temperature – °C Figure 15 126 fS = 48 kHz 124 fS = 192 kHz fS = 96 kHz 122 −25 0 25 50 TA – Free-Air Temperature – °C 75 100 120 −50 −25 0 25 50 TA – Free-Air Temperature – °C Figure 17 NOTE: PCM mode, VCC = 5 V, VDD = 3.3 V, measurement circuit is Figure 34 (VOUT = 4.5 V rms). 12 fS = 192 kHz Figure 18 75 100 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 0 −20 −20 −40 −60 Amplitude – dB Amplitude – dB −40 −80 −100 −120 −60 −80 −100 −120 −140 −140 −160 −180 −160 0 2 4 6 8 10 12 14 16 18 20 0 10 20 30 f – Frequency – kHz 40 50 60 70 80 90 100 f – Frequency – kHz Figure 19. –60-db Output Spectrum, BW = 20 kHz Figure 20. –60-db Output Spectrum, BW = 100 kHz NOTE: PCM mode, fS = 48 kHz, 32,768 point 8 average, TA = 25°C, VDD = 3.3 V, VCC = 5 V, measurement circuit is Figure 34. TOTAL HARMONIC DISTORTION + NOISE vs INPUT LEVEL THD+N – Total Harmonic Distortion + Noise – % 10 1 0.1 0.01 0.001 0.0001 −100 −80 −60 −40 −20 0 Input Level – dBFS Figure 21. THD+N vs Input Level, PCM Mode NOTE: PCM mode, fS = 48 kHz, TA = 25°C, VDD = 3.3 V, VCC = 5 V, measurement circuit is Figure 34. 13 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 AMPLITUDE vs FREQUENCY 0 −20 Amplitude – dB −40 −60 −80 −100 −120 −140 −160 0 2 4 6 8 10 12 14 16 18 20 f – Frequency – kHz Figure 22. –60-dB Output Spectrum, DSD Mode NOTE: DSD mode (FIR-4), 32,768 point 8 average, TA = 25°C, VDD = 3.3 V, VCC = 5 V, measurement circuit is Figure 35. AMPLITUDE vs FREQUENCY −130 −133 −136 Amplitude – dB −139 −142 −145 −148 −151 −154 −157 −160 0 2 4 6 8 10 12 14 16 18 20 f – Frequency – kHz Figure 23. –150-dB Output Spectrum, DSD Mono Mode NOTE: DSD mode (FIR-4), 32,768 point 8 average, TA = 25°C, VDD = 3.3 V, VCC = 5 V, measurement circuit is Figure 35. 14 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 SYSTEM CLOCK AND RESET FUNCTIONS System Clock Input The DSD1792A requires a system clock for operating the digital interpolation filters and advanced segment DAC modulators. The system clock is applied at the SCK input (pin 7). The DSD1792A has a system clock detection circuit that automatically senses if the system clock is operating between 128 fS and 768 fS. Table 1 shows examples of system clock frequencies for common audio sampling rates. If the oversampling rate of the delta-sigma modulator is selected as 128 fS, the system clock frequency is over 256 fS. Figure 24 shows the timing requirements for the system clock input. For optimal performance, it is important to use a clock source with low phase jitter and noise. One of the Texas Instruments’ PLL1700 family of multiclock generators is an excellent choice for providing the DSD1792A system clock. Table 1. System Clock Rates for Common Audio Sampling Frequencies SYSTEM CLOCK FREQUENCY (fSCK) (MHz) SAMPLING FREQUENCY 128 fS 192 fS 256 fS 384 fS 512 fS 768 fS 32 kHz 4.096 6.144 8.192 12.288 16.384 24.576 44.1 kHz 5.6488 8.4672 11.2896 16.9344 22.5792 33.8688 48 kHz 6.144 9.216 12.288 18.432 24.576 36.864 96 kHz 12.288 18.432 24.576 36.864 192 kHz 24.576 36.864 49.152 73.728 49.152 (1) 73.728 (1) (1) This system clock rate is not supported for the given sampling frequency. t(SCKH) H 2V System Clock (SCK) 0.8 V L t(SCKL) PARAMETERS t(SCY) MIN MAX UNITS t(SCY) System clock pulse cycle time t(SCKH) System clock pulse duration, HIGH 13 ns 0.4t(SCY) ns t(SCKL) System clock pulse duration, LOW 0.4t(SCY) ns Figure 24. System Clock Input Timing Power-On and External Reset Functions The DSD1792A includes a power-on reset function. Figure 25 shows the operation of this function. With VDD > 2 V, the power-on reset function is enabled. The initialization sequence requires 1024 system clocks from the time VDD > 2 V. After the initialization period, the DSD1792A is set to its default reset state, as described in the MODE CONTROL REGISTERS section of this data sheet. The DSD1792A also includes an external reset capability using the RST input (pin 14). This allows an external controller or master reset circuit to force the DSD1792A to initialize to its default reset state. Figure 26 shows the external reset operation and timing. The RST pin is set to logic 0 for a minimum of 20 ns. The RST pin is then set to a logic 1 state, thus starting the initialization sequence, which requires 1024 system clock periods. Operation of the external reset is the same as that of the power-on reset. The external reset is especially useful in applications where there is a delay between the DSD1792A power up and system clock activation. 15 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 VDD 2.4 V (Max) 2 V (Typ) 1.6 V (Min) Reset Reset Removal Internal Reset 1024 System Clocks System Clock Figure 25. Power-On Reset Timing RST (Pin 14) 50 % of VDD t(RST) Reset Reset Removal Internal Reset 1024 System Clocks System Clock t(RST) PARAMETERS MIN Reset pulse duration, LOW 20 Figure 26. External Reset Timing 16 MAX UNITS ns 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 AUDIO DATA INTERFACE Audio Serial Interface The audio interface port is a 3-wire serial port. It includes PLRCK (pin 4), PBCK (pin 6), and PDATA (pin 5). PBCK is the serial audio bit clock, and it is used to clock the serial data present on PDATA into the serial shift register of the audio interface. Serial data is clocked into the DSD1792A on the rising edge of PBCK. PLRCK is the serial audio left/right word clock. The DSD1792A requires the synchronization of PLRCK and the system clock, but does not need a specific phase relation between PLRCK and the system clock. If the relationship between PLRCK and the system clock changes more than ±6 PBCK, internal operation is initialized within 1/fS and analog outputs are forced to the bipolar zero level until resynchronization between PLRCK and the system clock is completed. PCM Audio Data Formats and Timing The DSD1792A supports industry-standard audio data formats, including standard right-justified, I2S, and left-justified. The data formats are shown in Figure 28. Data formats are selected using the format bits, FMT[2:0], in control register 18. The default data format is 24-bit I2S. All formats require binary 2s complement, MSB-first audio data. Figure 27 shows a detailed timing diagram for the serial audio interface. 50% of VDD PLRCK t(BCH) t(BCL) t(LB) 50% of VDD PBCK t(BCY) t(BL) 50% of VDD PDATA t(DS) t(DH) PARAMETERS MIN MAX UNITS t(BCY) t(BCL) PBCK pulse cycle time 70 ns PBCK pulse duration, LOW 30 ns t(BCH) t(BL) PBCK pulse duration, HIGH 30 ns PBCK rising edge to PLRCK edge 10 ns t(LB) t(DS) PLRCK edge to PBCK rising edge 10 ns PDATA Setup time 10 ns t(DH) — PDATA hold time 10 ns PLRCK clock data 50% ± 2 bit clocks Figure 27. Timing of Audio Interface 17 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 (1) Standard Data Format (Right-Justified); L-Channel = HIGH, R-Channel = LOW 1/fS PLRCK R-Channel L-Channel PBCK Audio Data Word = 16-Bit PDATA 14 15 16 1 2 MSB 15 16 1 2 15 16 LSB Audio Data Word = 20-Bit PDATA 18 19 20 1 2 19 20 1 2 19 20 LSB MSB Audio Data Word = 24-Bit PDATA 22 23 24 1 2 23 24 1 2 23 24 LSB MSB (2) Left-Justified Data Format; L-Channel = HIGH, R-Channel = LOW 1/fS PLRCK R-Channel L-Channel PBCK Audio Data Word = 24-Bit PDATA 1 2 23 24 1 2 23 24 1 2 LSB MSB (3) I2S Data Format; L-Channel = LOW, R-Channel = HIGH 1/fS PLRCK L-Channel R-Channel PBCK Audio Data Word = 16-Bit PDATA 1 2 15 16 MSB 1 2 1 2 15 16 1 2 1 2 LSB Audio Data Word = 24-Bit PDATA 1 2 23 24 MSB LSB Figure 28. Audio Data Input Formats 18 23 24 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 External Digital Filter Interface and Timing The DSD1792A supports an external digital filter interface comprising a 3- or 4-wire synchronous serial port, which allows the use of an external digital filter. External filters include the Texas Instruments’ DF1704 and DF1706, the Pacific Microsonics PMD200, or a programmable digital signal processor. In the external DF mode, PLRCK (pin 4), PBCK (pin 6) and PDATA (pin 5) are defined as WDCK, the word clock; BCK, the bit clock; and DATA, the monaural data, respectively. The external digital filter interface is selected by using the DFTH bit of control register 20, which functions to bypass the internal digital filter of the DSD1792A. When the DFMS bit of control register 19 is set, the DSD1792A can process stereo data. In this case, DSDL (pin 1) and DSDR (pin 2) are defined as L-channel data and R-channel data, respectively. Detailed information for the external digital filter interface mode is provided in the APPLICATION FOR EXTERNAL DIGITAL FILTER INTERFACE section of this data sheet. Direct Stream Digital (DSD) Format Interface and Timing The DSD1792A supports the DSD-format interface operation, which includes out-of-band noise filtering using an internal analog FIR filter. The DSD-format interface consists of a 3-wire synchronous serial port, which includes DBCK (pin 3), DSDL (pin 1), and DSDR (pin 2). DBCK is the serial bit clock. DSDL and DSDR are L-channel and R-channel DSD data input, respectively. They are clocked into the DSD1792A on the rising edge of DBCK. PLRCK (pin 4) and PBCK (pin 6) should be connected to GND in the DSD mode. The DSD-(DSD mode) format interface is activated by setting the DSD bit of control register 20. Detailed information for the DSD mode is provided in the APPLICATION FOR DSD FORMAT (DSD MODE) INTERFACE section of this data sheet. TDMCA Interface The DSD1792A supports the time-division-multiplexed command and audio (TDMCA) data format to enable control of and communication with a number of external devices over a single serial interface. Detailed information for the TDMCA format is provided in the TDMCA Format section of this data sheet. FUNCTION DESCRIPTIONS Serial Control Interface The serial control interface is a 4-wire synchronous serial port, which operates asynchronously with the serial audio interface and the system clock (SCK). The serial control interface is used to program and read the on-chip mode registers. The control interface includes MDO (pin 13), MDI (pin 11), MC (pin 12), and MS (pin 10). MDO is the serial data output, used to read back the values of the mode registers; MDI is the serial data input, used to program the mode registers; MC is the bit clock, used to shift data in and out of the control port, and MS is the mode control enable, used to enable the internal mode register access. Register Read/Write Operation All read/write operations for the serial control port use 16-bit data words. Figure 29 shows the control data word format. The most significant bit is the read/write (R/W) bit. For write operations, the R/W bit must be set to 0. For read operations, the R/W bit must be set to 1. There are seven bits, labeled IDX[6:0], that set the register index (or address) for the read and write operations. The least significant eight bits, D[7:0], contain the data to be written to the register specified by IDX[6:0] or to be read from, the register specified by IDX[6:0]. Figure 30 shows the functional timing diagram for writing or reading the serial control port. MS is held at a logic 1 state until a register needs to be written or read. To start the register write or read cycle, MS is set to logic 0. Sixteen clocks are then provided on MC, corresponding to the 16 bits of the control data word on MDI and readback data on MDO. After the eighth clock cycle has completed, the data from the indexed-mode control register appears on MDO during the read operation. After the sixteenth clock cycle has completed, the data is latched into the indexed-mode control register during the write operation. To write or read subsequent data, MS must be set to 1 once. LSB MSB R/W IDX6 IDX5 IDX4 IDX3 IDX2 Register Index (or Address) IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 D0 Register Data Figure 29. Control Data Word Format for MDI 19 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 MS MC MDI R/W A6 A5 A4 A3 A2 A1 A0 High Impedance MDO D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 When Read Mode is Instructed NOTE: Bit 15 is used for selection of write or read. Setting R/W = 0 indicates a write, while R/W = 1 indicates a read. Bits 14–8 are used for the register address. Bits 7–0 are used for register data. Figure 30. Serial Control Format t(MHH) MS 50% of VDD t(MSS) t(MCL) t(MCH) t(MSH) MC 50% of VDD t(MCY) LSB MDI t(MDS) 50% of VDD t(MOS) t(MDH) MDO 50% of VDD PARAMETER t(MCY) t(MCL) MC pulse cycle time MIN MAX ns MC low-level time 40 ns t(MCH) t(MHH) MC high-level time 40 ns MS high-level time 80 ns t(MSS) t(MSH) MS falling edge to MC rising edge MS hold time(1) 15 ns 15 ns t(MDH) t(MDS) MDI hold time 15 ns MDI setup time 15 t(MOS) MC falling edge to MDO stable (1) MC rising edge for LSB to MS rising edge Figure 31. Control Interface Timing 20 UNITS 100 ns 30 ns 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 yesMODE CONTROL REGISTERS User-Programmable Mode Controls The DSD1792A includes a number of user-programmable functions which are accessed via mode control registers. The registers are programmed using the serial control interface, which was previously discussed in this data sheet. Table 2 lists the available mode-control functions, along with their default reset conditions and associated register index. Table 2. User-Programmable Function Controls FUNCTION DEFAULT REGISTER BIT PCM DSD DF BYPASS Digital attenuation control 0 dB to –120 dB and mute, 0.5 dB/step 0 dB Register 16 Register 17 ATL[7:0] (for L-ch) ATR[7:0] (for R-ch) yes Attenuation load control—Disabled, enabled Attenuation disabled 24-bit I2S format Register 18 ATLD yes Register 18 FMT[2:0] yes Sampling rate selection for de-emphasis Disabled, 44.1 kHz, 48 kHz, 32 kHz De-emphasis disabled Register 18 DMF[1:0] yes De-emphasis control—Disabled, enabled De-emphasis disabled Register 18 DME yes Soft mute control—Mute disabled, enabled Mute disabled Register 18 MUTE yes Output phase reversal—Normal, reverse Normal Register 19 REV yes Attenuation speed selection ×1 fS, ×(1/2) fS, ×(1/4) fS, ×(1/8) fS ×1 fS Register 19 ATS[1:0] yes DAC operation control—Enabled, disabled DAC operation enabled Register 19 OPE yes Zero flag pin operation control DSD data input, zero flag output DSD data input Register 19 ZOE yes Stereo DF bypass mode select Monaural, stereo Monaural Register 19 DFMS Digital filter rolloff selection Sharp rolloff, slow rolloff Sharp rolloff Register 19 FLT yes Infinite zero mute control Disabled, enabled Disabled Register 19 INZD yes System reset control Reset operation, normal operation Normal operation Register 20 SRST yes yes DSD interface mode control DSD enabled, disabled Disabled Register 20 DSD yes yes Digital-filter bypass control DF enabled, DF bypass DF enabled Register 20 DFTH yes Monaural mode selection Stereo, monaural Stereo Register 20 MONO yes yes yes Channel selection for monaural mode data L-channel, R-channel L-channel Register 20 CHSL yes yes yes Delta-sigma oversampling rate selection ×64 fS, ×128 fS, ×32 fS ×64 fS Register 20 OS[1:0] yes yes(2) yes PCM zero output enable Enabled Register 21 PCMZ yes DSD zero output enable Disabled Register 21 DZ[1:0] Not zero = 0 Zero detected = 1 Register 22 ZFGL (for L-ch) ZFGR (for R-ch) Input audio data format selection 16-, 20-, 24-bit standard (right-justified) format 24-bit MSB-first left-justified format 16-/24-bit I2S format yes yes(1) yes yes yes yes yes yes yes yes yes yes yes Function available only for read Zero detection flag Not zero, zero detected Device ID (at TDMCA) — Register 23 ID[4:0] (1) When in DSD mode, DMF[1:0] is defined as DSD filter (analog FIR) performance selection. (2) When in DSD mode, OS[1:0] is defined as DSD filter (analog FIR) operation rate selection. yes yes yes yes 21 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Register Map The mode control register map is shown in Table 3. Registers 16–21 include an R/W bit, which determines whether a register read (R/W = 1) or write (R/W = 0) operation is performed. Registers 22 and 23 are read-only. Table 3. Mode Control Register Map B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 16 R/W 0 0 1 0 0 0 0 ATL7 ATL6 ATL5 ATL4 ATL3 ATL2 ATL1 ATL0 Register 17 R/W 0 0 1 0 0 0 1 ATR7 ATR6 ATR5 ATR4 ATR3 ATR2 ATR1 ATR0 Register 18 R/W 0 0 1 0 0 1 0 ATLD FMT2 FMT1 FMT0 DMF1 DMF0 DME MUTE Register 19 R/W 0 0 1 0 0 1 1 REV ATS1 ATS0 OPE ZOE DFMS FLT INZD Register 20 R/W 0 0 1 0 1 0 0 RSV SRST DSD DFTH MONO CHSL OS1 OS0 Register 21 R/W 0 0 1 0 1 0 1 RSV RSV RSV RSV RSV DZ1 DZ0 PCMZ Register 22 R 0 0 1 0 1 1 0 RSV RSV RSV RSV RSV RSV ZFGR ZFGL Register 23 R 0 0 1 0 1 1 1 RSV RSV RSV ID4 ID3 ID2 ID1 ID0 Register Definitions B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 16 R/W 0 0 1 0 0 0 0 ATL7 ATL6 ATL5 ATL4 ATL3 ATL2 ATL1 ATL0 Register 17 R/W 0 0 1 0 0 0 1 ATR7 ATR6 ATR5 ATR4 ATR3 ATR2 ATR1 ATR0 R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 ATx[7:0]: Digital Attenuation Level Setting These bits are available for read and write. Default value: 1111 1111b Each DAC output has a digital attenuator associated with it. The attenuator can be set from 0 dB to –120 dB, in 0.5-dB steps. Alternatively, the attenuator can be set to infinite attenuation (or mute). The attenuation data for each channel can be set individually. However, the data load control (the ATLD bit of control register 18) is common to both attenuators. ATLD must be set to 1 in order to change an attenuator setting. The attenuation level can be set using the following formula: Attenuation level (dB) = 0.5 dB • (ATx[7:0] DEC – 255) where ATx[7:0]DEC = 0 through 255 For ATx[7:0]DEC = 0 through 14, the attenuator is set to infinite attenuation. The following table shows attenuation levels for various settings: 22 ATx[7:0] Decimal Value Attenuation Level Setting 1111 1111b 255 0 dB, no attenuation (default) 1111 1110b 254 –0.5 dB 1111 1101b 253 –1.0 dB L L 0001 0000b 16 –119.5 dB 0000 1111b 15 –120.0 dB 0000 1110b 14 Mute L L L 0000 0000b 0 Mute L 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Register 18 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 R/W 0 0 1 0 0 1 0 ATLD FMT2 FMT1 FMT0 B3 B2 DMF1 DMF0 B1 B0 DME MUTE R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 ATLD: Attenuation Load Control This bit is available for read and write. Default value: 0 ATLD = 0 Attenuation control disabled (default) ATLD = 1 Attenuation control enabled The ATLD bit is used to enable loading of the attenuation data contained in registers 16 and 17. When ATLD = 0, the attenuation settings remain at the previously programmed levels, ignoring new data loaded from registers 16 and 17. When ATLD = 1, attenuation data written to registers 16 and 17 is loaded normally. FMT[2:0]: Audio Interface Data Format These bits are available for read and write. Default value: 101 For the external digital filter interface mode (DFTH mode), this register is operated as shown in the Application for Interfacing With an External Digital Filter section of this data sheet. FMT[2:0] Audio Data Format Selection 000 16-bit standard format, right-justified data 001 20-bit standard format, right-justified data 010 24-bit standard format, right-justified data 011 24-bit MSB-first, left-justified data 100 16-bit I2S-format data 101 24-bit I2S-format data (default) 110 Reserved 111 Reserved The FMT[2:0] bits are used to select the data format for the serial audio interface. DMF[1:0]: Sampling Frequency Selection for the De-Emphasis Function These bits are available for read and write. Default value: 00 DMF[1:0] De-Emphasis Sampling Frequency Selection 00 Disabled (default) 01 48 kHz 10 44.1 kHz 11 32 kHz The DMF[1:0] bits are used to select the sampling frequency used by the digital de-emphasis function when it is enabled by setting the DME bit. The de-emphasis curves are shown in the TYPICAL PERFORMANCE CURVES section of this data sheet. For the DSD mode, analog FIR filter performance can be selected using this register. Filter response plots are shown in the TYPICAL PERFORMANCE CURVES section of this data sheet. A register map is shown in the Configuration for the DSD Interface Mode section of this data sheet. 23 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 DME: Digital De-Emphasis Control This bit is available for read and write. Default value: 0 DME = 0 De-emphasis disabled (default) DME = 1 De-emphasis enabled The DME bit is used to enable or disable the de-emphasis function for both channels. MUTE: Soft Mute Control This bit is available for read and write. Default value: 0 MUTE = 0 MUTE disabled (default) MUTE = 1 MUTE enabled The MUTE bit is used to enable or disable the soft mute function for both channels. Soft mute is operated as a 256-step attenuator. The speed for each step to –∞ dB (mute) is determined by the attenuation rate selected in the ATS register. Register 19 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 R/W 0 0 1 0 0 1 1 REV ATS1 ATS0 OPE ZOE DFMS FLT INZD R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 REV: Output Phase Reversal This bit is available for read and write. Default value: 0 REV = 0 Normal output (default) REV = 1 Inverted output The REV bit is used to invert the output phase for both channels. ATS[1:0]: Attenuation Rate Select These bits are available for read and write. Default value: 00 ATS[1:0] Attenuation Rate Selection 00 PLRCK/1 (default) 01 PLRCK/2 10 PLRCK/4 11 PLRCK/8 The ATS[1:0] bits are used to select the rate at which the attenuator is decremented/incremented during level transitions. 24 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 OPE: DAC Operation Control This bit is available for read and write. Default value: 0 OPE = 0 DAC operation enabled (default) OPE = 1 DAC operation disabled The OPE bit is used to enable or disable the analog output for both channels. Disabling the analog outputs forces them to the bipolar zero level (BPZ) even if digital audio data is present on the input. ZOE: Zero Flag Pin Operation Control This bit is available for read and write. Default value: 0 ZOE = 0 DSD data input (default) ZOE = 1 Zero flag output The ZOE bit is used to change the DSDL (pin 1) and DSDR (pin 2) pin assignments. When the ZOE bit is set to 0, DSDL and DSDR are inputs for L-channel and R-channel data. When the ZOE bit is set to 1, DSDL and DSDR become outputs for the L-channel and R-channel zero flags, respectively. See the PCMZ and DZ[1:0] bit descriptions of register 21. DFMS: Stereo DF Bypass Mode Select This bit is available for read and write. Default value: 0 DFMS = 0 Monaural (default) DFMS = 1 Stereo input enabled The DFMS bit is used to enable stereo operation in DF bypass mode. In the DF bypass mode, when DFMS is set to 0, the pin for the input data is PDATA (pin 5) only, therefore the DSD1792A operates as a monaural DAC. When DFMS is set to 1, the DSD1792A can operate as a stereo DAC with inputs of input L-channel and R-channel data on DSDL (pin 1) and DSDR (pin 2), respectively. FLT: Digital Filter Rolloff Control This bit is available for read and write. Default value: 0 FLT = 0 Sharp rolloff (default) FLT = 1 Slow rolloff The FLT bit is used to select the digital filter rolloff characteristic. The filter responses for these selections are shown in the TYPICAL PERFORMANCE CURVES section of this data sheet. INZD: Infinite Zero Detect Mute Control This bit is available for read and write. Default value: 0 INZD = 0 Infinite zero detect mute disabled (default) INZD = 1 Infinite zero detect mute enabled The INZD bit is used to enable or disable the zero detect mute function. Setting INZD to 1 forces muted analog outputs to hold a bipolar zero level when the DSD1792A detects zero data in both channels continuously for 1024 sampling periods (1/fS). The infinite zero detect mute function is not available in the DSD mode. 25 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Register 20 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 R/W 0 0 1 0 1 0 0 RSV SRST DSD DFTH MONO CHSL OS1 OS0 R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 SRST: System Reset Control This bit is available for write only. Default value: 0 SRST = 0 Normal operation (default) SRST = 1 System reset operation (generate one reset pulse) The SRST bit is used to reset the DSD1792A to the initial system condition. DSD: DSD Interface Mode Control This bit is available for read and write. Default value: 0 DSD = 0 DSD interface mode disabled (default) DSD = 1 DSD interface mode enabled The DSD bit is used to enable or disable the DSD interface mode. DFTH: Digital Filter Bypass (or Through Mode) Control This bit is available for read and write. Default value: 0 DFTH = 0 Digital filter enabled (default) DFTH = 1 Digital filter bypassed for external digital filter The DFTH bit is used to enable or disable the external digital filter interface mode. MONO: Monaural Mode Selection This bit is available for read and write. Default value: 0 MONO = 0 Stereo mode (default) MONO = 1 Monaural mode The MONO function is used to change the operation mode from the normal stereo mode to the monaural mode. When the monaural mode is selected, both DACs operate in a balanced mode for one channel of audio input data. Channel selection is available for L-channel or R-channel data, determined by the CHSL bit as described immediately following. CHSL: Channel Selection for Monaural Mode This bit is available for read and write. Default value: 0 This bit is available when MONO = 1. CHSL = 0 L-channel selected (default) CHSL = 1 R-channel selected The CHSL bit selects L-channel or R-channel data to be used in monaural mode. 26 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 OS[1:0]: Delta-Sigma Oversampling Rate Selection These bits are available for read and write. Default value: 00 OS[1:0] Operation Speed Select 00 64 times fS (default) 01 32 times fS 10 128 times fS 11 Reserved The OS bits are used to change the oversampling rate of delta-sigma modulation. Use of this function enables the designer to stabilize the conditions at the post low-pass filter for different sampling rates. As an application example, programming to set 128 times in 44.1-kHz operation, 64 times in 96-kHz operation, and 32 times in 192-kHz operation allows the use of only a single type (cutoff frequency) of post low-pass filter. The 128-fS oversampling rate is not available at sampling rates above 100 kHz. If the 128-fS oversampling rate is selected, a system clock of more than 256 fS is required. In DSD mode, these bits are used to select the speed of the bit clock for DSD data coming into the analog FIR filter. Register 21 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 R/W 0 0 1 0 1 0 1 RSV RSV RSV RSV RSV DZ1 DZ0 PCMZ R/W: Read/Write Mode Select When R/W = 0, a write operation is performed. When R/W = 1, a read operation is performed. Default value: 0 DZ[1:0]: DSD Zero Output Enable These bits are available for read and write. Default value: 00 DZ[1:0] Zero Output Enable 00 Disabled (default) 01 Even pattern detect 1x 96H pattern detect The DZ bits are used to enable or disable the output zero flags, and to select the zero pattern in the DSD mode. The DSD1792A sets zero flags when the 1 and 0 data are even in every 8 bits of DSD input data, or the DSD input data is 1001 0110 continuously for 200 ms. PCMZ: PCM Zero Output Enable These bits are available for read and write. Default value: 1 PCMZ = 0 PCM zero output disabled PCMZ = 1 PCM zero output enabled (default) The PCMZ bit is used to enable or disable the output zero flags in the PCM mode and the external DF mode. The DSD1792A sets the zero flags when the input data is continuously zero for 1024 LRCKs in the PCM mode or 1024 WDCKs in the external filter mode. Register 22 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 R 0 0 1 0 1 1 0 RSV RSV RSV RSV RSV RSV ZFGR ZFGL R: Read Mode Select Value is always 1, specifying the readback mode. 27 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ZFGx: Zero-Detection Flag Where x = L or R, corresponding to the DAC output channel. These bits are available only for readback. Default value: 00 ZFGx = 0 Not zero ZFGx = 1 Zero detected When the DSD1792A detects that audio input data is continuously zero, the ZFGx bit is set to 1 for the corresponding channel(s). Register 23 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 R 0 0 1 0 1 1 1 RSV RSV RSV ID4 ID3 ID2 ID1 ID0 R: Read Mode Select Value is always 1, specifying the readback mode. ID[4:0]: Device ID The ID[4:0] bits show a device ID in the TDMCA mode. TYPICAL CONNECTION DIAGRAM IN PCM MODE Cf 5V Rf 0.1 µF DSD Audio Data Source PCM Audio Data Source 1 DSDL VCC2L 28 2 DSDR AGND3L 27 3 DBCK IOUTL– 26 4 PLRCK IOUTL+ 25 5 PDATA AGND2 24 6 PBCK VCC1 23 7 0.1 µF Controller SCK 8 DGND 9 VDD VCOML DSD1792A 21 IREF 20 10 MS AGND1 19 11 MDI IOUTR– 18 12 MC IOUTR+ 17 AGND3R 16 VCC2R 15 14 RST 10 µF – + Cf Rf 5V – 47 µF + 22 VCOMR 13 MDO + – + Cf Rf 5V – 10 µF VOUT R-Channel Rf 10 kΩ + Differential to Single Converter With Low-Pass Filter Cf 47 µF 0.1 µF VOUT L-Channel + + 10 µF + Differential to Single Converter With Low-Pass Filter + 3.3 V + 10 µF Figure 32. Typical Application Circuit for Standard PCM Audio Operation 28 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 APPLICATION INFORMATION APPLICATION CIRCUIT The design of the application circuit is important in order to actually realize the high S/N ratio of which the DSD1792A is capable. This is because noise and distortion that are generated in an application circuit are not negligible. In the circuit of Figure 33, the output level is 2 V rms and 127 dB S/N is achieved. The circuit of Figure 34 can realize the highest performance. In this case the output level is set to 4.5 V rms and 129 dB S/N is achieved (stereo mode). In monaural mode, if the output of the L-channel and R-channel is used as a balanced output, 132 dB S/N is achieved (see Figure 36). Figure 35 shows a circuit for the DSD mode, which is a 4th-order LPF in order to reduce the out-of-band noise. I/V Section The current of the DSD1792A on each of the output pins (IOUTL+, IOUTL–, IOUTR+, IOUTR–) is 7.8 mA p-p at 0 dB (full scale). The voltage output level of the I/V converter (Vi) is given by following equation: Vi = 7.8 mA p-p × Rf (Rf : feedback resistance of I/V converter) An NE5534 operational amplifier is recommended for the I/V circuit to obtain the specified performance. Dynamic performance such as the gain bandwidth, settling time, and slew rate of the operational amplifier affects the audio dynamic performance of the I/V section. Differential Section The DSD1792A voltage outputs are followed by differential amplifier stages, which sum the differential signals for each channel, creating a single-ended I/V op-amp output. In addition, the differential amplifiers provide a low-pass filter function. The operational amplifier recommended for the IV circuit is the NE5534, and the operational amplifier recommended for the differential circuit is the Linear Technology LT1028, because their input noise is low. 29 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 C1 2200 pF R1 750 Ω VCC VCC C11 0.1 µF C17 22 pF 7 IOUT– 5 2 8 – 3 R5 270 Ω 6 + C3 2700 pF R3 560 Ω C19 33 pF 7 2 U1 NE5534 4 C15 0.1 µF 3 5 – 6 + 4 C12 0.1 µF VEE R4 560 Ω R6 270 Ω U3 LT1028 C16 0.1 µF C4 2700 pF VEE C2 2200 pF R2 750 Ω VCC C13 0.1 µF C18 22 pF 7 IOUT+ 2 3 5 – VCC = 15 V VEE = –15 V fC = 217 kHz 8 6 + 4 U2 NE5534 C14 0.1 µF VEE Figure 33. Measurement Circuit for PCM, VOUT = 2 V rms 30 R7 100 Ω 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 C1 2200 pF R1 820 Ω VCC VCC C11 0.1 µF C17 22 pF 7 IOUT– 5 2 8 – 3 R5 360 Ω 6 + C3 2700 pF R3 360 Ω C19 33 pF 7 2 U1 NE5534 4 C15 0.1 µF 3 5 – 6 + 4 C12 0.1 µF VEE R4 360 Ω R6 360 Ω R7 100 Ω U3 LT1028 C16 0.1 µF C4 2700 pF VEE C2 2200 pF R2 820 Ω VCC C13 0.1 µF C18 22 pF 7 IOUT+ 2 3 VCC = 15 V VEE = –15 V fC = 162 kHz 5 – 8 6 + 4 U2 NE5534 C14 0.1 µF VEE Figure 34. Measurement Circuit for PCM, VOUT = 4.5 V rms 31 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 C1 2200 pF R1 820 Ω VCC VCC C11 0.1 µF C17 22 pF 7 IOUT– 5 2 8 – 3 R5 330 Ω 6 + R3 110 Ω R10 68 Ω C3 18000 pF U1 NE5534 4 R8 220 Ω C5 10000 pF C15 0.1 µF C19 33 pF 7 2 C4 47000 pF 3 5 – 6 + 4 C12 0.1 µF VEE R4 110 Ω R9 220 Ω R6 330 Ω R11 68 Ω C14 0.1 µF C6 10000 pF VEE C2 2200 pF R2 820 Ω VCC C13 0.1 µF 7 IOUT+ 2 3 VCC = 15 V VEE = –15 V fC = 38 kHz C18 22 pF 5 – 8 6 + 4 U2 NE5534 C14 0.1 µF VEE Figure 35. Measurement Circuit for DSD 32 U3 LT1028 R7 100 Ω 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 IOUTL– (Pin 26) IOUT– OUT+ Figure 34 Circuit IOUTL+ (Pin 25) IOUT+ 3 1 2 IOUTR– (Pin 18) IOUT– OUT– Figure 34 Circuit IOUTR+ (Pin 17) Balanced Out IOUT+ Figure 36. Measurement Circuit for Monaural Mode APPLICATION FOR EXTERNAL DIGITAL FILTER INTERFACE DFMS = 0 External Filter Device DSD1792A 1 DSDL 2 DSDR 3 DBCK WDCK (Word Clock) 4 PLRCK DATA 5 PDATA BCK 6 PBCK SCK 7 SCK DFMS = 1 External Filter Device DSD1792A DATA_L 1 DSDL DATA_R 2 DSDR 3 DBCK 4 PLRCK 5 PDATA BCK 6 PBCK SCK 7 SCK WDCK (Word Clock) Figure 37. Connection Diagram for External DIgital Filter (Internal DF Bypass Mode) Application 33 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Application for Interfacing With an External Digital Filter For some applications, it may be desirable to use an external digital filter to perform the interpolation function, as it can provide improved stop-band attenuation when compared to the internal digital filter of the DSD1792A. The DSD1792A supports several external digital filters, including: D Texas Instruments DF1704 and DF1706 D Pacific Microsonics PMD200 HDCD filter/decoder IC D Programmable digital signal processors The external digital filter application mode is accessed by programming the following bits in the corresponding control register: D DFTH = 1 (register 20) The pins used to provide the serial interface for the external digital filter are shown in the connection diagram of Figure 37. The word (WDCK) signal must be operated at 8× or 4× the desired sampling frequency, fS. System Clock (SCK) and Interface Timing The DSD1792A in an application using an external digital filter requires the synchronization of WDCK and the system clock. The system clock is phase-free with respect to WDCK. Interface timing among WDCK, BCK, DATAL, and DATAR is shown in Figure 39. Audio Format The DSD1792A in the external digital filter interface mode supports right-justified audio formats including 16-bit, 20-bit, and 24-bit audio data, as shown in Figure 38. The audio format is selected by the FMT[2:0] bits of control register 18. 34 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 1/4 fS or 1/8 fS WDCK BCK Audio Data Word = 16-Bit DATA 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MSB LSB Audio Data Word = 20-Bit DATA 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MSB LSB Audio Data Word = 24-Bit DATA 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 MSB LSB Figure 38. Audio Data Input Format for External Digital Filter (Internal DF Bypass Mode) Application WDCK (LRCK) 50% of VDD t(BCH) t(BCL) t(LB) 50% of VDD BCK t(BCY) t(BL) 50% of VDD DATA t(DS) t(DH) PARAMETER t(BCY) BCK pulse cycle time t(BCL) BCK pulse duration, LOW MIN MAX UNITS 20 ns 7 ns t(BCH) BCK pulse duration, HIGH t(BL) BCK rising edge to WDCK falling edge 7 ns 5 ns t(LB) t(DS) WDCK falling edge to BCK rising edge 5 ns DATA setup time 5 ns t(DH) DATA hold time 5 ns Figure 39. Audio Interface Timing for External Digital Filter (Internal DF Bypass Mode) Application 35 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Functions Available in the External Digital Filter Mode The external digital filter mode allows access to the majority of the DSD1792A mode control functions. The following table shows the register mapping available when the external digital filter mode is selected, along with descriptions of functions which are modified when using this mode selection. B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 16 R/W 0 0 1 0 0 0 0 – – – – – – – – Register 17 R/W 0 0 1 0 0 0 1 – – – – – – – – Register 18 R/W 0 0 1 0 0 1 0 – FMT2 FMT1 FMT0 – – – – Register 19 R/W 0 0 1 0 0 1 1 REV – – OPE – DFMS – INZD Register 20 R/W 0 0 1 0 1 0 0 – SRST 0 1 MONO CHSL OS1 OS0 Register 21 R/W 0 0 1 0 1 0 1 – – – – – – – PCMZ 0 – – – – – – ZFGR ZFGL Register 22 R 0 0 1 0 1 1 NOTE: 1: Bit is required for selection of external digital filter mode. –: Function is disabled. No operation even if data bit is set FMT[2:0]: Audio Data Format Selection Default value: 000 FMT[2:0] Audio Data Format Select 000 16-bit right-justified format (default) 001 20-bit right-justified format 010 24-bit right-justified format Other N/A OS[1:0]: Delta-Sigma Modulator Oversampling Rate Selection Default value: 00 OS[1:0] Operation Speed Select 00 8 times WDCK (default) 01 4 times WDCK 10 16 times WDCK 11 Reserved The effective oversampling rate is determined by the oversampling performed by both the external digital filter and the delta-sigma modulator. For example, if the external digital filter is 8× oversampling, and the user selects OS[1:0] = 00, then the delta-sigma modulator oversamples by 8×, resulting in an effective oversampling rate of 64×. The 16× WDCK oversampling rate is not available above a 100-kHz sampling rate. If the oversampling rate selected is 16× WDCK, the system clock frequency must be over 256 fS. 36 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 APPLICATION FOR DSD FORMAT (DSD MODE) INTERFACE DSD Decoder DSD1792A DATA_L 1 DSDL DATA_R 2 DSDR Bit Clock 3 DBCK 4 PLRCK 5 PDATA 6 PBCK 7 SCK System Clock (1) (1) The system clock can be removed after setting the register to the DSD mode. Figure 40. Connection Diagram in DSD Mode Feature This mode is used for interfacing directly to a DSD decoder, which is found in Super Audio CDt (SACD) applications. The DSD mode is accessed by programming the following bit in the corresponding control register. DSD = 1 (register 20) The DSD mode provides a low-pass filtering function. The filtering is provided using an analog FIR filter structure. Four FIR responses are available and are selected by the DMF[1:0] bits of control register 18. Super Audio CD is a trademark of Sony Kabushiki Kaisha TA Sony Corporation, Japan. 37 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Pin Assignment When DSD Format Interface Several pins are redefined for DSD mode operation. These include: D DSDL (pin 1): DATAL as L-channel DSD data input D DSDR (pin 2): DATAR as R-channel DSD data input D DBCK (pin 3): Bit clock (BCK) for DSD data t = 1/(64 × 44.1 kHz) DBCK DSDL DSDR D0 D1 D2 D3 D4 Figure 41. Normal Data Output Form From DSD Decoder t(BCH) t(BCL) 50% of VDD DBCK t(BCY) DSDL DSDR 50% of VDD t(DS) t(DH) PARAMETER t(BCY) DBCK pulse cycle time t(BCH) DBCK high-level time t(BCL) DBCK low-level time t(DS) DSDL, DSDR setup time t(DH) DSDL, DSDR hold time (1) 2.8224 MHz × 4. (2.8224 MHz = 64 × 44.1 kHz. This value is specified as a sampling rate of DSD.) Figure 42. Timing for DSD Audio Interface 38 MIN 85(1) MAX UNITS ns 30 ns 30 ns 10 ns 10 ns 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 ANALOG FIR FILTER PERFORMANCE IN DSD MODE GAIN vs FREQUENCY GAIN vs FREQUENCY 0 0 −1 −10 −2 −20 Gain – dB Gain – dB fc = 185 kHz Gain(1) = –6.6 dB −3 −30 −4 −40 −5 −50 −6 −60 0 50 100 150 200 0 500 f – Frequency – kHz 1000 1500 f – Frequency – kHz Figure 43. DSD Filter-1, Low BW Figure 44. DSD Filter-1, High BW GAIN vs FREQUENCY GAIN vs FREQUENCY 0 0 −1 −10 −2 −20 Gain – dB Gain – dB fc = 77 kHz Gain(1) = –6 dB −3 −30 −4 −40 −5 −50 −6 −60 0 50 100 150 200 0 500 f – Frequency – kHz Figure 45. DSD Filter-2, Low BW 1000 1500 f – Frequency – kHz Figure 46. DSD Filter-2, High BW (1) This gain is in comparison to PCM 0 dB, when the DSD input signal efficiency is 50%. All specifications at DBCK = 2.8224 MHz (44.1 kHz × 64 fS), and 50% modulation DSD data input, unless otherwise noted. 39 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 GAIN vs FREQUENCY GAIN vs FREQUENCY 0 0 −1 −10 −2 −20 Gain – dB Gain – dB fc = 85 kHz Gain(1) = –1.5 dB −3 −30 −4 −40 −5 −50 −60 −6 0 50 100 150 0 200 500 1000 1500 f – Frequency – kHz f – Frequency – kHz Figure 47. DSD Filter-3, Low BW Figure 48. DSD Filter-3, High BW GAIN vs FREQUENCY GAIN vs FREQUENCY 0 0 −1 −10 −2 −20 Gain – dB Gain – dB fc = 94 kHz Gain(1) = –3.3 dB −3 −30 −4 −40 −5 −50 −6 −60 0 50 100 150 200 0 f – Frequency – kHz Figure 49. DSD Filter-4, Low BW 500 1000 f – Frequency – kHz Figure 50. DSD Filter-4, High BW (1) This gain is in comparison to PCM 0 dB, when the DSD input signal efficiency is 50%. All specifications at DBCK = 2.8224 MHz (44.1 kHz × 64 fS), and 50% modulation DSD data input, unless otherwise noted. 40 1500 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 DSD MODE CONFIGURATION AND FUNCTION CONTROLS Configuration for the DSD Interface Mode DSD = 1 (Register 20, B5) B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 Register 16 R/W 0 0 1 0 0 0 0 – – – – – – – – Register 17 R/W 0 0 1 0 0 0 1 – – – – – – – – Register 18 R/W 0 0 1 0 0 1 0 – – – – DMF1 DMF0 – – Register 19 R/W 0 0 1 0 0 1 1 REV – – OPE – – – – Register 20 R/W 0 0 1 0 1 0 0 – SRST 1 – MONO CHSL OS1 OS0 Register 21 R 0 0 1 0 1 0 1 – – – – – DZ1 DZ0 – 0 – – – – – – ZFGR ZFGL Register 22 R 0 0 1 0 1 1 : NOTE –: Function is disabled. No operation even if data bit is set DMF[1:0]: Analog FIR Performance Selection Default value: 00 DMF[1:0] Analog-FIR Performance Select 00 FIR-1 (default) 01 FIR-2 10 FIR-3 11 FIR-4 Plots for the four analog FIR filter responses are shown in the TYPICAL PERFORMANCE CURVES section of this data sheet. OS[1:0]: Analog-FIR Operation-Speed Selection Default value: 00 OS[1:0] Operation Speed Select 00 fDBCK (default) 01 fDBCK/2 10 Reserved 11 fDBCK/4 The OS bit in the DSD mode is used to select the operating rate of the analog FIR. The OS bits must be set before setting the DSD bit to 1. Requirements for System Clock The bit clock (BCK) for the DSD mode is required at pin 3 of the DSD1792A. The frequency of the bit clock can be N times the sampling frequency. Generally, N is 64 in DSD applications. The interface timing between the bit clock and DATAL and DATAR is required to meet the same setup- and hold-time specifications as shown for the audio interface timing in Figure 42. 41 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 TDMCA Format The DSD1792A supports the time-division-multiplexed command and audio (TDMCA) data format to simplify the host control serial interface. The TDMCA format is designed not only for the McBSP of TI DSPs but also for any programmable devices. The TDMCA format can transfer not only audio data but also command data, so that it can be used together with any kind of device that supports the TDMCA format. The TDMCA frame consists of command field, extended command field, and some audio data fields. Those audio data are transported to IN devices (such as a DAC) and/or from OUT devices (such as an ADC). The DSD1792A is an IN device. LRCK and BCK are used with both IN and OUT devices so that the sample frequency of all devices in a system must be the same. The TDMCA mode supports a maximum of 30 device IDs. The maximum number of audio channels depends on the BCK frequency. TDMCA Mode Determination The DSD1792A recognizes the TDMCA mode automatically when it receives an LRCK signal with a pulse duration of two BCK clocks. If the TDMCA mode operation is not needed, the duty cycle of LRCK must be 50%. Figure 51 shows the LRCK and BCK timing that determines the TDMCA mode. The DSD1792A enters the TDMCA mode after two continuous TDMCA frames. Any TDMCA commands can be issued during the next TDMCA frame after the TDMCA mode is entered. Pre-TDMCA Frame TDMCA Frame Command Accept LRCK 2 BCK BCK Figure 51. LRCK and BCK Timing of Determination TDMCA Mode TDMCA Terminals TDMCA requires six signals, of which four signals are for command and audio data interface, and one pair is for daisy chaining. Those signals can be shared as in the following table. The DO signal has a 3-state output so that it can be connected directly to other devices. TERMINAL NAME TDMCA NAME I/O PLRCK LRCK I TDMCA frame start signal. It must be the same as the sampling frequency. PBCK BCK I TDMCA clock. Its frequency must be high enough to communicate a TDMCA frame within an LRCK cycle. PDATA DI I TDMCA command and audio data input signal MDO DO O TDMCA command data 3-state output signal MC DCI I TDMCA daisy-chain input signal MS DCO O TDMCA daisy-chain output signal 42 DESCRIPTION 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Device ID Determination The TDMCA mode also supports a multichip implementation in one system. This means a host controller (DSP) can simultaneously support several TDMCA devices, which can be of the same type or different types, including PCM devices. The PCM devices are categorized as IN device, OUT device, IN/OUT device, and NO device. The IN device has an input port to get audio data, the OUT device has an output port to supply audio data, the IN/OUT device has both input and output ports for audio data, and the NO device has no port for audio data but needs command data from the host. A DAC is an IN device, an ADC is an OUT device, a CODEC is an IN/OUT device, and a PLL is a NO device. The DSD1792A is an IN device. For the host controller to distinguish the devices, each device is assigned its own device ID by the daisy chain. The devices obtain their own device IDs automatically by connecting their DCI to the DCO of the preceding device and their DCO to the DCI of the following device in the daisy chain. The daisy chains are categorized as the IN chain and the OUT chain, which are completely independent and equivalent. Figure 52 shows an example daisy-chain connection. If a system needs to chain the DSD1792A and a NO device in the same IN or OUT chain, the NO device should be chained at the back end of the chain because it does not require any audio data. Figure 53 shows an example of TDMCA system including an IN chain and an OUT chain with a TI DSP. For a device to get its own device ID, the DID signal must be set to 1 (see the Command Field section for details), and LRCK and BCK must be driven in the TDMCA mode for all PCM devices which are chained. The device at the top of the chain knows its device ID is 1 because its DCI is fixed HIGH. Other devices count the BCK pulses and observe their own DCI signal to determine their position and ID. Figure 54 shows the initialization of each device ID. IN DCO DCI DCO DCI NO Device NO Device DCO ••• DCI DCO DCIo OUT DCOo NO Device IN/OUT Device OUT DCIo DCO DCI DCO DCI ••• ••• ••• NO Device DCI IN/OUT Device OUT Device DCOi IN DCOo IN Device OUT Device DCIi DCOi DCIi ••• IN Device DCO DCI DCO DCI IN Chain OUT Chain Figure 52. Daisy-Chain Connection 43 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 DCII LRCK BCK IN/OUT Device (DIX1700) DCOI DI DCIO DO DCOO Device ID = 1 LRCK BCK IN Device (DSD1792A) DI DO LRCK DCI DCO Device ID = 2 NO Device DCI BCK DI DO DCO Device ID = 3 • • • FSX FSR CLKX CLKR DX DR LRCK OUT Device DCI BCK DI DO DCO Device ID = 2 TI DSP LRCK OUT Device DCI BCK DI DO DCO Device ID = 3 • • • Figure 53. IN Daisy-Chain and OUT Daisy-Chain Connection for a Multichip System 44 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 LRCK BCK DID DI Device ID = 1 DCO1 Device ID = 2 DCO1 DCI2 Command Field Device ID = 3 DCO2 DCI3 • • • • • • Device ID = 30 DCO29 DCI30 58 BCK Figure 54. Device ID Determination Sequence TDMCA Frame In general, the TDMCA frame consists of the command field, extended command (EMD) field, and audio data fields. All of them are 32 bits in length, but the lowest byte has no meaning. The MSB is transferred first for each field. The command field is always transferred as the first packet of the frame. The EMD field is transferred if the EMD flag of the command field is HIGH. If any EMD packets are transferred, no audio data follows the EMD packets. This frame is for quick system initialization. All devices of a daisy chain should respond to the command field and extended command field. The DSD1792A has two audio channels that can be selected by OPE (register 19). If the OPE bit is not set HIGH, those audio channels are transferred. Figure 55 shows the general TDMCA frame. If some DACs are enabled, but corresponding audio data packets are not transferred, the analog outputs are unpredictable. 1/fS LRCK BCK [For Initialization] DI CMD EMD EMD EMD EMD EMD CMD CMD CMD CMD CMD Don’t Care CMD Don’t Care CMD 32 Bits DO CMD [For Operation] DI CMD DO CMD Ch1 Ch1 Ch2 Ch3 Ch4 Ch(n) Ch2 Ch3 Ch4 Ch(m) Figure 55. General TDMCA Frame 45 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 1/fS (256 BCK Clocks) 7 Packets × 32 Bits LRCK BCK DI Ch1 CMD Ch2 Ch3 Ch4 Ch5 Ch6 Don’t Care CMD IN and OUT Channel Orders are Completely Independent DO Ch1 CMD Ch2 Figure 56. TDMCA Frame Example of 6-Ch DAC and 2-Ch ADC With Command Read Command Field The normal command field is defined as follows. When the DID bit (MSB) is 1, this frame is used only for device ID determination, and all remaining bits in the field are ignored. Command 31 30 29 DID EMD DCS 28 24 Device ID 23 22 R/W 16 15 Register ID 8 7 Data 0 Not Used Bit 31: Device ID enable flag The DSD1792A operates to get its own device ID for TDMCA initialization if this bit is HIGH. Bit 30: Extended command enable flag EMD packet is transferred if this bit is HIGH, otherwise skipped. Once this bit is HIGH, this frame does not contain any audio data. This is for system initialization. Bit 29: Daisy-chain selection flag HIGH designates OUT-chain devices, LOW designates IN-chain devices. The DSD1792A is an IN device, so the DCS bit must be set to LOW. Bits[28:24]: Device ID. It is 5 bits length, and it can be defined. These bits identify the order of a device in the IN or OUT daisy chain. The top of the daisy chain defines device ID 1 and successive devices are numbered 2, 3, 4, etc. All devices for which the DCI is fixed HIGH are also defined as ID 1. The maximum device ID is 30 each in the IN and OUT chains. If a device ID of 0x1F is used, all devices are selected as broadcast when in the write mode. If a device ID of 0x00 is used, no device is selected. Bit 23: Command Read/Write flag If this bit is HIGH, the command is a read operation. Bits[22:16]: Register ID It is 7 bits in length. Bits[15:8]: Command data It is 8 bits in length. Any valid data can be chosen for each register. Bits[7:0]: Not used These bits are never transported when a read operation is performed. Extended command field The extended command field is the same as the command field, except that it does not have a DID flag. Extended Command 46 31 30 29 Rsvd EMD DCS 28 24 Device ID 23 R/W 22 16 Register ID 15 8 Data 7 0 Not Used 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Audio Fields The audio field is 32 bits in length and the audio data is transferred MSB first, so the other fields must be stuffed with 0s as shown in the following example. Audio Data 31 16 MSB 24 Bits 12 8 7 LSB 4 3 0 All 0s TDMCA Register Requirements TDMCA mode requires device ID and audio channel information, previously described. The OPE bit in register 19 indicates audio channel availability and register 23 indicates the device ID. Register 23 is used only in the TDMCA mode. See the mode control register map (Table 3). Register Write/Read Operation The command supports register write and read operations. If the command requests to read one register, the read data is transferred on DO during the data phase of the timing cycle. The DI signal can be retrieved at the positive edge of BCK, and the DO signal is driven at the negative edge of BCK. DO is activated one BCK cycle early to compensate for the output delay caused by high impedance. Figure 57 shows the TDMCA write and read timing. Register ID Phase Data Phase BCK DI Read Mode and Proper Register ID DO Write Data Retrieved, if Write Mode Read Data Driven, if Read Mode 1 BCK Early DOEN (Internal) Figure 57. TDMCA Write and Read Operation Timing TDMCA-Mode Operation DCO specifies the owner of the next audio channel in TDMCA-mode operation. When a device retrieves its own audio channel data, DCO goes HIGH during the last audio channel period. Figure 58 shows the DCO output timing in TDMCA-mode operation. The host controller ignores the behavior of DCI and DCO. DCO indicates the last audio channel of each device. Therefore, DCI means the next audio channel is allocated. If some devices are skipped due to no active audio channel, the skipped devices must notify the next device that the DCO will be passed through the next DCI. Figure 59 and Figure 60 show DCO timing with skip operation. Figure 61 shows the ac timing of the daisy-chain signals. 47 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 1/fS (384 BCK Clocks) 9 Packets × 32 Bits LRCK BCK IN Daisy Chain CMD DI Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 Ch8 Don’t Care DCI1 DID = 1 DID = 2 DID = 3 DID = 4 DCO1 DCI2 DCO2 DCI3 DCO3 DCI4 DCO4 Figure 58. DCO Output Timing of TDMCA Mode Operation 1/fS (256 BCK Clocks) 5 Packets × 32 Bits LRCK BCK DI CMD Ch1 Ch2 Ch15 Ch16 Don’t Care DCI DID = 1 DCO DCI DID = 2 • • • • • • 2 BCK Delay DCO • • • 14 BCK Delay DCI DID = 8 DCO Figure 59. DCO Output Timing With Skip Operation 48 CMD CMD 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Command Packet LRCK BCK DI DID EMD DCO1 DCO2 • • • Figure 60. DCO Output Timing With Skip Operation (for Command Packet 1) 49 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 LRCK t(LB) t(BL) BCK t(BCY) t(DS) t(DH) DI t(DOE) DO t(DS) t(DH) DCI t(COE) DCO PARAMETER t(BCY) BCK pulse cycle time t(LB) LRCK setup time MIN MAX UNITS 20 ns 0 ns t(BL) t(DS) LRCK hold time 3 ns DI setup time 0 ns t(DH) t(DS) DI hold time 3 ns DCI setup time 0 ns 3 ns t(DH) DCI hold time t(DOE) DO output delay(1) t(COE) DCO output delay(1) (1) Load capacitance is 10 pF. Figure 61. AC Timing of Daisy-Chain Signals 50 8 ns 6 ns 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 THEORY OF OPERATION Upper 6 Bits ICOB Decoder 0–62 Level 0–66 Advanced DWA Digital Input 24 Bits 8 fS MSB and Lower 18 Bits 3rd-Order 5-Level Sigma-Delta Current Segment DAC Analog Output 0–4 Level Figure 62. Advanced Segments DAC The DSD1792A uses TI’s advanced segment DAC architecture to achieve excellent dynamic performance and improved tolerance to clock jitter. The DSD1792A provides balanced current outputs. Digital input data via the digital filter is separated into six upper bits and 18 lower bits. The six upper bits are converted to inverted complementary offset binary (ICOB) code. The lower 18 bits, associated with the MSB, are processed by a five-level third-order delta-sigma modulator operated at 64 fS by default. The 1 level of the modulator is equivalent to the 1 LSB of the ICOB code converter. The data groups processed in the ICOB converter and third-order delta-sigma modulator are summed together to an up to 66-level digital code, and then processed by data-weighted averaging (DWA) to reduce the noise produced by element mismatch. The data of up to 66 levels from the DWA is converted to an analog output in the differential-current segment section. This architecture has overcome the various drawbacks of conventional multibit processing and also achieves excellent dynamic performance. 51 

 www.ti.com SLES106B − FEBRUARY 2004 − REVISED NOVEMBER 2006 Analog output The following table and Figure 63 show the relationship between the digital input code and analog output. IOUTN [mA] IOUTP [mA] VOUTN [V] VOUTP [V] 800000 (–FS) 000000 (BPZ) 7FFFFF (+FS) –2.3 –6.2 –10.1 –10.1 –6.2 –2.3 –1.725 –4.650 –7.575 –7.575 –4.650 –1.725 VOUT [V] –2.821 0 2.821 : NOTE VOUTN is the output of U1, VOUTP is the output of U2, and VOUT is the output of U3 in the application circuit of Figure 33. OUTPUT CURRENT vs INPUT CODE 0 IO – Output Current – mA −2 IOUTN −4 −6 −8 −10 IOUTP −12 800000(–FS) 000000(BPZ) 7FFFFF(+FS) Input Code – Hex Figure 63. The Relationship Between Digital Input and Analog Output 52 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) DSD1792ADB ACTIVE SSOP DB 28 47 RoHS & Green NIPDAU Level-1-260C-UNLIM -25 to 85 DSD1792 A Samples DSD1792ADBR ACTIVE SSOP DB 28 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -25 to 85 DSD1792 A Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of