DVI-FPDLINKII-R/NOPB

DVI - FPD LINK II (DS90UR905Q / 906Q) Demo Platform User Guide General Description The DVI-FPD LINK II demo platform takes the DVI signals as a video input, and deserializes the parallel RGB and control signals. The DS90UR905Q converts this 24-bit parallel RGB data and control data to a high-speed serialized (FPD-LINK II) over a single pair with up to 10m STP cable. The DS90UR906Q recovers the data (RGB) and control signals, and extracts the clock from the serial stream. The recovered RGB and control data are converted back to the DVI signals as a video output to any Displays (See Figure 1). Figure 1. Block Diagram Ordering Information Parts: DS90UR905Q & DS90UR906Q Demo boards: DVI-FPDLINKII-M (Molex Cable) DVI-FPDLINKII-R (Rosenberger / Leoni Cable) DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 1 Figure 2. Setup Diagram Figure 3. Bottom Board DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 2 Figure 4. Top Board Quick Start Guide • • • • • • • • • The DVI – FPD Link II demo board consists of a “top board” and a “bottom” board The “Top board” has the DS90UR905 and DS90UR906 devices The “Bottom board” has the TI DVI TX and RX devices Connect the included 12V AC/DC power adapter to the “CON3” of the top board Connect the PC (DVI Source) to DVI connector “CON1” (inputs to TI RX) of the bottom board Connect the LCD to DVI connector “CON2” (outputs from TI TX) of the bottom board On DVI-FPDLINKII-R board, connect the Rosenberger/Leoni cable between “CON4” (from 905 output) and “CON5” (to 906 input) of the top board On DVI-FPDLINKII-M board, connect the Molex cable between “CON7” (from 905 output) and “CON8” (to 906 input) of the top board Three GREEN LEDs on the top board are ON and the picture should be seen on the LCD D1 – “Lock” indication of TI DVI RX device D3 – “Lock” indication of DS90UR906Q D4 – “Pass” indication of DS90UR906Q DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 3 Other Optional Notes • • Bypass EEPROM The resolution of video source is controlled by “EDID”. The EDID is provided by the display directly or an EEPROM. Configure Jumper “J4” and “J5” as shown in Figure 3. 1-2: EDID from EEPROM 2-3: EDID from Display (Default Setting) Long Cable Length VODSEL and De-Emphasis controls – Turn both positions “ON” as shown in Figure 4 when longer cable is used. • SW6 • Control switch of DS90UR905Q (refer to the datasheet). SW4 & SW5 Control switches of DS90UR906Q (refer to the datasheet). Bill of Materials # Quat Reference Digikey PN Manufacture PN Descriptions 1 2 CON1,CON2 WM5601-ND 74320-4004 CONN RECEPT RT ANG DIGITAL DVI 2 1 CON3 CP-037BH-ND PJ-037BH CON PWR JACK 2.5 X 6.5MM 3 3 CON4,CON5,CON6 NA D4S20D-40ML5-Z HSD 2x2 MALE R/A 4 3 CON7,CON8,CON9 WM17535-ND 49616-0711 5 1 CON10 CP1-3513SJCT-ND SJ1-3513-SMT 6 1 CON11 WM5461CT-ND 67503-1020 7 3 C1,C2,C110 495-2236-1-ND B45196H3106K109 HDR USCAR MINI USB A R/A BLACK CONN JACK STEREO 3POS 3.5MM SMD CONN RECEPT MINIUSB R/A 5POS SMD CAP TANTALUM 10UF 16V 10% SMD 1206 8 39 C3,C4,C5,C6,C7,C8,C9,C10, PCC2336CT-ND ECJ-ZEB0J104M CAP CERAMIC .1UF 6.3V X5R 0201 PCC2136CT-ND ECJ-ZEB0J103K CAP .01UF 6.3V CERAMIC X5R 0201 C89, C92 C94 0402ZD103KAT2AND 0402ZD103KAT2A CAP CER 10000PF 10V X5R 0402 C70,C71,C72,C73,C74, PCC2364CT-ND ECJ-0EB1A105M CAP CERAMIC 1UF 10V X5R 0402 511-1498-1-ND TCTAL0J107M8R CAP TANTALUM 100UF 6.3V 20% SMD 1206 C11,C12,C13,C29,C30,C33, C34,C35,C36,C37,C43,C44, C45,C46, C51,C52,C53,C54,C55,C56, C57,C76,C77,C78,C101,C116 C102,C103,C104,C105,C106 9 22 C14,C15,C16,C17,C18,C19, C20,C21,C22,C38,C39,C40, C41,C42,C58,C59,C60,C61, C62,C79,C80,C117 10 3 11 15 C75,C86,C87 C107,C108,C109, C115,C118, C119 12 2 C26,C27 DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 4 13 1 C23 1206ZD105MAT2AND 1206ZD105MAT2A 14 2 C28,C95 511-1502-1-ND TCTAL1C226M8R LMK325B7106MN-T CAP CER 1.0UF 10V X5R 1206 CAP TANTALUM 22UF 16V 20% SMD 1206 15 2 C91,C97 587-1469-1-ND 16 2 C98,C99 587-1387-1-ND 17 2 C88,C93 490-3043-1-ND GRM31MR60J475KC11L CAP CER 4.7UF 6.3V 10% X5R 1206 18 1 C90 490-3161-1-ND GRM033R61A152KA01D CAP CER 1500PF 10V X5R 0201 19 1 C96 490-3163-1-ND GRM033R61A332KA01D 20 25 MK325BJ107MM-T R26,R27,R28,R29,R30,R31, CAP CER 10UF 10V X7R 1210 CAP CER 100UF 6.3V X5R 1210 CAP CER 3300PF 10V X5R 0201 DNI - SMD 0402 C82,R32,R33,R37,R39, R41,R46,R48,R50,R53,R75, R76,R77,R78,R79,R89, R90,R91,R117 21 6 C31,C32,C47,C48,C49,C50 23 1 C63 511-1443-1-ND TCP0J475M8R CAP TANT 4.7UF 6.3V 20% SMD 0805 DNI - SMD 0201 24 1 C64 PCC2421CT-ND ECJ-0EB0J225M CAP CERAMIC 2.2UF 6.3V X5R 0402 25 2 C65,C66 445-4993-1-ND C1005X5R0J224K CAP CER .22UF 6.3V X5R 0402 26 3 C67,C68,C69 478-5526-1-ND TLNS227M004R3000 CAP TANT 220UF 4.0V SMD 1206 27 1 C81 PCC1748CT-ND ECJ-1VB1A154K CAP .15UF 10V CERAMIC X5R 0603 28 3 C83,C84,C85 587-1455-1-ND LMK105BJ474KV-F CAP CER .47UF 10V X5R 0402 29 2 C111,C112 C0402C223K9PACTU CAP 22000PF 6.3V CERAM X5R 0402 30 2 C113,C114 399-3014-1-ND 04026D100JAT2AND 04026D100JAT2A CAP CER 10PF 6.3V X5R 0402 31 3 D1,D3,D4 511-1592-1-ND SML-P12PTT86 LED GREEN 0.2MM 13MCD 0402 SMD 32 1 D2 511-1594-1-ND SML-P12VTT86 LED RED 0.2MM 60MCD 0402 SMD 33 4 D5,D6,D7,D8 160-1816-1-ND LTPL-P013WST1 LED 3 WATT COOL WHITE SMD 34 3 D9 568-4118-1-ND PMEG2020EH,115 35 2 J1,J2 3M9465-ND 961240-6404-AR 22 2 J8,J9 3M9531-ND 960240-6202-AR 36 1 J3 3M9463-ND 961224-6404-AR SCHOTTKY RECT 20V 2A SOD123F CONN HEADER VERT DUAL 40POS GOLD CONN SOCKET VERT DUAL 40POS GOLD CONN HEADER VERT DUAL 24POS GOLD CONN HEADER 3POS .100 VERT GOLD 37 3 J4,J5,J14 WM6503-ND 22-28-4033 38 1 J6 3M5473-ND 4808-3004-CP 39 3 J7,J11,J12 WM6502-ND 22-28-4023 40 2 J10,J13 WM6504-ND 22-28-4043 SOCKET IC OPEN FRAME 8POS .3" CONN HEADER 2POS .100 VERT GOLD CONN HEADER 4POS .100 VERT GOLD 41 1 J15 WM26814-ND 10-89-7142 CONN HDR DUAL 14POS .100 SRT AU 42 1 J16 WM26808-ND 10-89-7082 CONN HDR DUAL 8POS .100 SRT AU 43 1 J17 WM26806-ND 10-89-7062 CONN HDR DUAL 6POS .100 SRT AU 44 1 L1 732-1258-1-ND 744773122 INDUCTOR POWER 22UH 1.0A SMD 45 34 R1,R2,R3,R4,R5,R6,R7,R8, RHM10.0KLCT-ND MCR01MZPF1002 RES 10.0K OHM 1/16W 1% 0402 SMD R9,R10,R11,R15,R16,R18 R19,R20,R25,R52,R58,R60, R61,R62,R63,R64,R65,R66, R67,R68,R69,R70,R71,R72, R73,R74 DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 5 46 1 R17 RHM1.50KLCT-ND MCR01MZPF1501 RES 1.5K OHM 1/16W 1% 0402 SMD 47 1 R12 P510LCT-ND ERJ-2RKF5100X RES 510 OHM 1/10W 1% 0402 SMD 48 5 R13,R14,R34,R35,R36 RHM4.7KJCT-ND MCR01MZPJ472 RES 4.7K OHM 1/16W 5% 0402 SMD 49 1 R108 RHM1.50KLCT-ND MCR01MZPF1501 RES 1.50K OHM 1/16W 1% 0402 SMD 50 4 R21,R22,R23,R24 RHM220LCT-ND MCR01MZPF2200 RES 220 OHM 1/16W 1% 0402 SMD 51 17 R38,R40,R42,R43,R44,R45, P0.0JCT-ND ERJ-2GE0R00X RES 0.0 OHM 1/10W 5% 0402 SMD R47,R49,R51,R54,R55,R56, R109,R110,R111,R112,R118 52 2 R113,R114 P0.0ACT-ND ERJ-6GEY0R00V RES 0.0 OHM 1/8W 5% 0805 SMD 53 1 R57 P422LCT-ND ERJ-2RKF4220X RES 422 OHM 1/10W 1% 0402 SMD 54 1 R80 P61.9KLCT-ND ERJ-2RKF6192X RES 61.9K OHM 1/10W 1% 0402 SMD 55 3 R83 P1.54KLCT-ND ERJ-2RKF1541X RES 1.54K OHM 1/10W 1% 0402 SMD 56 1 R84 P536LCT-ND ERJ-2RKF5360X RES 536 OHM 1/10W 1% 0402 SMD 59 1 R92 HPC12100JCT-ND HPC 12 100 5% R RES 100 OHM 5W 5% SMD 60 1 R101 P1.00MLCT-ND ERJ-2RKF1004X RES 1.00M OHM 1/10W 1% 0402 SMD 61 4 R102,R103,R104,R105 P3.30KLCT-ND ERJ-2RKF3301X RES 3.30K OHM 1/10W 1% 0402 SMD 62 2 R107,R106 P16.0LCT-ND ERJ-2RKF16R0X RES 16.0 OHM 1/10W 1% 0402 SMD 63 1 R115 P12.0KLCT-ND ERJ-2RKF1202X RES 12.0K OHM 1/10W 1% 0402 SMD 64 1 R116 P5.60KLCT-ND ERJ-2RKF5601X RES 5.60K OHM 1/10W 1% 0402 SMD 65 2 R81,R82 P5.1KJCT-ND ERJ-2GEJ512X RES 5.1K OHM 1/10W 5% 0402 SMD 66 2 R85,R87 P1.00KLCT-ND ERJ-2RKF1001X RES 1.00K OHM 1/10W 1% 0402 SMD 67 1 R86 P2.32KLCT-ND ERJ-2RKF2321X RES 2.32K OHM 1/10W 1% 0402 SMD 68 1 R88 P806LCT-ND ERJ-2RKF8060X RES 806 OHM 1/10W 1% 0402 SMD 69 4 SW1,SW4,SW6,SW8 CT2196MST-ND 219-6MST SWITCH TAPE SEAL 6 POS SMD 70 1 SW2 CT2194MST-ND 219-4MST SWITCH TAPE SEAL 4 POS SMD 71 2 SW3,SW7 P12225SCT-ND EVQ-21505R SWITCH LT 6MM 160GF 5MM HEIGHT 72 1 SW5 CT2198MST-ND 219-8MST SWITCH TAPE SEAL 8 POS SMD SWITCH SLIDE SPDT 3A 125VAC PCB 73 1 SW9 360-2131-ND CS12ANW03 74 1 U1 296-9992-ND TFP401PZP IC PANELBUS DVI REC 100-HTQFP 75 1 U2 296-12666-ND TFP410PAP IC TRANSMITTER DIGITAL 64-HTQFP 76 1 U3 NA DS90UR905Q IC SERIALIZER 48-LLP 77 1 U4 NA DS90UR906Q 78 1 U5 LM4934RLCT-ND LM4934RL IC DESERIALIZER 60-LLP IC AUDIO SUBSYSTEM 1.2W 42USMDXT 79 1 U6 80 2 U7 PCM2706PJT LM22680MREADJ/NOPB IC STEREO AUD DAC W/USB 32-TQFP IC VREG SW STP-DWN 2A ADJ 8PSOP 81 1 U8,U9 296-15275-5-ND LM22680MREADJCT-ND LP3878MR-ADJND LP3878MR-ADJ/NOPB IC VREG 800MA ADJ 8-PSOP 82 1 U10 428-2188-5-ND CY2302SXI-1 IC CLK FREQ MULTI/ZDB 2OUT 8SOIC 83 1 X1 CTX410-ND ATS120 CRYSTAL 12.0000 MHZ SERIES RES 84 1 Y1 CTX303LVCT-ND CB3LV-3I-12M0000 OSC 12.0000 MHZ 3.3V SMD DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 6 Schematics DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 7 DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 8 DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 9 DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 10 Reference Layouts Top layer Bottom Board Top Board Bottom Board Top Board Bottom layer DVI – FPD LINK II Demo Platform User Guide Rev1.1 October 2010 © National Semiconductor Corporation 11 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated