Stellaris® LM4F120 LaunchPad Evaluation
Board
User Manual
Literature Number: SPMU289C
August 2012 – Revised September 2013
Contents
A
.......................................................................................................................... 4
Board Overview .................................................................................................................. 5
1.1
Kit Contents .................................................................................................................. 6
1.2
Using the Stellaris LaunchPad ............................................................................................ 6
1.3
Features ...................................................................................................................... 6
1.4
BoosterPacks ................................................................................................................ 7
1.5
Specifications ................................................................................................................ 7
Hardware Description .......................................................................................................... 8
2.1
Functional Description ...................................................................................................... 8
2.1.1 Microcontroller ...................................................................................................... 8
2.1.2 USB Device ......................................................................................................... 9
2.1.3 User Switches and RGB User LED .............................................................................. 9
2.1.4 Headers and BoosterPacks ....................................................................................... 9
2.2
Power Management ....................................................................................................... 12
2.2.1 Power Supplies ................................................................................................... 12
2.2.2 Hibernate .......................................................................................................... 12
2.2.3 Clocking ............................................................................................................ 12
2.2.4 Reset ............................................................................................................... 12
2.3
Stellaris In-Circuit Debug Interface (ICDI) .............................................................................. 13
2.3.1 Virtual COM Port ................................................................................................. 13
Software Development ....................................................................................................... 14
3.1
Software Description ...................................................................................................... 14
3.2
Source Code ............................................................................................................... 14
3.3
Tool Options ................................................................................................................ 14
3.4
Programming the Stellaris LaunchPad Evaluation Board ............................................................ 15
References, PCB Layout, and Bill of Materials ...................................................................... 16
4.1
References ................................................................................................................. 16
4.2
Component Locations ..................................................................................................... 17
4.3
Bill of Materials (BOM) .................................................................................................... 18
Schematics ....................................................................................................................... 20
2
Contents
Revision History
1
2
3
4
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
www.ti.com
List of Figures
1-1.
Stellaris LM4F120 LaunchPad Evaluation Board .......................................................................
5
2-1.
Stellaris LaunchPad Evaluation Board Block Diagram.................................................................
8
4-1.
Stellaris LaunchPad Component Locations (Top View) ..............................................................
17
4-2.
Stellaris LaunchPad Dimensions ........................................................................................
18
List of Tables
1-1.
EK-LM4F120XL Specifications ............................................................................................
7
2-1.
USB Device Signals ........................................................................................................
9
2-2.
User Switches and RGB LED Signals
2-3.
J1 Connector ...............................................................................................................
10
2-4.
J2 Connector ...............................................................................................................
10
2-5.
J3 Connector ...............................................................................................................
11
2-6.
J4 Connector ...............................................................................................................
11
2-7.
Stellaris In-Circuit Debug Interface (ICDI) Signals ....................................................................
13
2-8.
Virtual COM Port Signals .................................................................................................
13
4-1.
EK-LM4F120 Bill of Materials
...........................................................................................
18
...................................................................................
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
List of Figures
9
3
Revision History
www.ti.com
Revision History
This revision history highlights the changes made to the SPMU289B user's manual to make it an SPMU289C
revision.
SEE
Section 2.1.4
Headers and BoosterPacks
ADDITIONS/MODIFICATIONS/DELETIONS
Table 2-3, J1 Connector:
• Updated/Changed first column header cell from "J4 Pin" to "J1 Pin"
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
4
Revision History
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Chapter 1
SPMU289C – August 2012 – Revised September 2013
Board Overview
The Stellaris® LM4F120 LaunchPad Evaluation Board (EK-LM4F120XL) is a low-cost evaluation platform
for ARM® Cortex™-M4F-based microcontrollers. The Stellaris LaunchPad design highlights the
LM4F120H5QR microcontroller USB 2.0 device interface and hibernation module. The Stellaris
LaunchPad also features programmable user buttons and an RGB LED for custom applications. The
stackable headers of the Stellaris LM4F120 LaunchPad BoosterPack XL interface demonstrate how easy
it is to expand the functionality of the Stellaris LaunchPad when interfacing to other peripherals with
Stellaris BoosterPacks and MSP430™™ BoosterPacks. Figure 1-1 shows a photo of the Stellaris
LaunchPad.
Figure 1-1. Stellaris LM4F120 LaunchPad Evaluation Board
Power Select
Switch
USB Connector
Green Power LED
(Power/ICDI)
Reset Switch
USB Micro-B
Connector
(Device)
RGB User LED
Stellaris® LaunchPad
BoosterPack XL
Interface (J1, J2, J3,
and J4 Connectors)
Stellaris® LaunchPad
BoosterPack XL
Interface (J1, J2, J3,
and J4 Connectors)
Stellaris®
LM4F120H5QR
Microcontroller
MSP430™
LaunchPad-Compatible
BoosterPack Interface
MSP430™
LaunchPad-Compatible
BoosterPack Interface
User Switch 1
User Switch 2
MSP430, Code Composer Studio are trademarks of Texas Instruments.
Stellaris is a registered trademark of Texas Instruments.
Cortex is a trademark of ARM Limited.
ARM, RealView are registered trademarks of ARM Limited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
All other trademarks are the property of their respective owners.
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Board Overview
5
Kit Contents
1.1
www.ti.com
Kit Contents
The Stellaris LM4F120 LaunchPad Evaluation Kit contains the following items:
• Stellaris LaunchPad Evaluation Board (EK-LM4F120XL)
• On-board Stellaris In-Circuit Debug Interface (ICDI)
• USB micro-B plug to USB-A plug cable
• README First document
1.2
Using the Stellaris LaunchPad
The recommended steps for using the Stellaris LM4F120 LaunchPad Evaluation Kit are:
1. Follow the README First document included in the kit. The README First document will help you
get the Stellaris LaunchPad up and running in minutes. See the Stellaris LaunchPad web page for
additional information to help you get started.
2. Experiment with LaunchPad BoosterPacks. A selection of Stellaris BoosterPacks and compatible
MSP430 BoosterPacks can be found at the Stellaris LaunchPad web page.
3. Take your first step toward developing an application with Project 0 using your preferred ARM
tool-chain and the Stellaris Peripheral Driver Library. Software applications are loaded using the
on-board Stellaris In-Circuit Debug Interface (ICDI). See Chapter 3, Software Development, for the
programming procedure. The StellarisWare Peripheral Driver Library Software Reference Manual
contains specific information on software structure and function. For more information on Project 0, go
to the Stellaris LaunchPad wiki page.
4. Customize and integrate the hardware to suit an end application. This user's manual is an
important reference for understanding circuit operation and completing hardware modification.
You can also view and download almost six hours of training material on configuring and using the
LaunchPad. Visit the Stellaris LaunchPad Workshop for more information and tutorials.
1.3
Features
Your Stellaris LaunchPad includes the following features:
• Stellaris LM4F120H5QR microcontroller
• USB micro-B connector for USB device
• RGB user LED
• Two user switches (application/wake)
• Available I/O brought out to headers on a 0.1-in (2.54-mm) grid
• On-board Stellaris ICDI
• Switch-selectable power sources:
– ICDI
– USB device
• Reset switch
• Preloaded RGB quickstart application
• Supported by StellarisWare software including the USB library and the peripheral driver library
• Stellaris LM4F120 LaunchPad BoosterPack XL Interface, which features stackable headers to expand
the capabilities of the Stellaris LaunchPad development platform
– For a complete list of available BoosterPacks that can be used with the Stellaris LaunchPad, see
the Stellaris LaunchPad web page.
6
Board Overview
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
BoosterPacks
www.ti.com
1.4
BoosterPacks
The Stellaris LaunchPad provides an easy and inexpensive way to develop applications with the Stellaris
LM4F120H5QR microcontroller. Stellaris BoosterPacks and MSP430 BoosterPacks expand the available
peripherals and potential applications of the Stellaris LaunchPad. BoosterPacks can be used with the
Stellaris LaunchPad or you can simply use the on-board LM4F120H5QR microcontroller as its processor.
See Chapter 2 for more information.
Build your own BoosterPack and take advantage of Texas Instruments’ website to help promote it! From
sharing a new idea or project, to designing, manufacturing, and selling your own BoosterPack kit, TI offers
a variety of avenues for you to reach potential customers with your solutions.
1.5
Specifications
Table 1-1 summarizes the specifications for the Stellaris LaunchPad.
Table 1-1. EK-LM4F120XL Specifications
Parameter
Value
Board supply voltage
Dimensions
Break-out power output
RoHS status
4.75 VDC to 5.25 VDC from one of the following sources:
• Debugger (ICDI) USB Micro-B cable (connected to a
PC)
• USB Device Micro-B cable (connected to a PC)
2.0 in x 2.25 in x 0.425 in (5.0 cm x 5.715 cm x 10.795
mm) (L x W x H)
• 3.3 VDC (300 mA max)
• 5.0 VDC (depends on 3.3 VDC usage, 23 mA to 323
mA)
Compliant
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Board Overview
7
Chapter 2
SPMU289C – August 2012 – Revised September 2013
Hardware Description
The Stellaris LaunchPad includes a Stellaris LM4F120H5QR microcontroller and an integrated Stellaris
ICDI as well as a range of useful peripheral features (as the block diagram in Figure 2-1 shows). This
chapter describes how these peripherals operate and interface to the microcontroller.
Figure 2-1. Stellaris LaunchPad Evaluation Board Block Diagram
Debug Breakout Pads
JTAG/SWD
GPIO
I/O
Stellaris®
LaunchPad-Specific
BoosterPack XL
Expansion Headers
GPIO
I/O
MSP430™
LaunchPad-Compatible
Expansion Headers
Stellaris ICDI
UART0
LM4F120H5QR
USB Device
Connector
USB
Device
ICDI
USB Debug
Connector
GPIO
Power Select
Switch
RGB LED
VDD
HIB WAKE
GPIO
User
Switches
Power
Management
Breakout Pads
2.1
Functional Description
2.1.1 Microcontroller
The Stellaris LM4F120H5QR is a 32-bit ARM Cortex-M4F-based microcontroller with 256-KB Flash
memory, 32-KB SRAM, 80-MHz operation, USB device, Hibernation module, and a wide range of other
peripherals. See the LM4F120H5QR microcontroller data sheet (literature number SPMS294) for complete
device details.
8
Hardware Description
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Functional Description
www.ti.com
Most of the microcontroller signals are routed to 0.1-in (2.54-mm) pitch headers. An internal multiplexer
allows different peripheral functions to be assigned to each of these GPIO pads. When adding external
circuitry, consider the additional load on the evaluation board power rails.
The LM4F120H5QR microcontroller is factory-programmed with a quickstart demo program. The
quickstart program resides in on-chip Flash memory and runs each time power is applied, unless the
quickstart application has been replaced with a user program.
2.1.2 USB Device
The Stellaris LaunchPad includes a USB micro-B connector to allow for USB 2.0 device operation. The
signals shown in Table 2-1 are used for USB device.
Table 2-1. USB Device Signals
GPIO Pin
Pin Function
USB Device
PD4
USB0DM
D–
PD5
USB0DP
D+
When connected as a USB device, the evaluation board can be powered from either the Stellaris ICDI or
the USB Device connectors. The user can select the power source by moving the POWER SELECT
switch (SW3) to the Device position. See the Power Management schematic (appended to this document).
2.1.3 User Switches and RGB User LED
The Stellaris LaunchPad comes with an RGB LED. This LED is used in the preloaded RGB quickstart
application and can be configured for use in custom applications.
Two user buttons are included on the board. The user buttons are both used in the preloaded quickstart
application to adjust the light spectrum of the RGB LED as well as go into and out of hibernation. The user
buttons can be used for other purposes in the user’s custom application.
The evaluation board also has a green power LED. Table 2-2 shows how these features are connected to
the pins on the microcontroller.
Table 2-2. User Switches and RGB LED Signals
GPIO Pin
Pin Function
USB Device
PF4
GPIO
SW1
PF0
GPIO
SW2
PF1
GPIO
RGB LED (Red)
PF2
GPIO
RGB LED (Blue)
PF3
GPIO
RGD LED (Green)
2.1.4 Headers and BoosterPacks
The two double rows of stackable headers are mapped to most of the GPIO pins of the LM4F120H5QR
microcontroller. These rows are labeled as connectors J1, J2, J3, and J4. Connectors J3 and J4 are
located 0.1 in (2.54 mm) inside of the J1 and J2 connectors. All 40 header pins of the J1, J2, J3, and J4
connectors make up the Stellaris LM4F120 LaunchPad BoosterPack XL Interface. Table 2-3 through
Table 2-6 show how these header pins are connected to the microcontroller pins and which GPIO
functions can be selected.
NOTE: To configure the device peripherals easily and intuitively using a graphical user interface
(GUI), see the Stellaris LM4F Pinmux Utility found at www.ti.com/tool/lm4f_pinmux. This
easy-to-use interface makes setting up alternate functions for GPIOs simple and error-free.
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Hardware Description
9
Functional Description
www.ti.com
Table 2-3. J1 Connector
J1 Pin
GPIO
Stellaris
Pin
GPIOPCTL Register Setting
GPIOAMSEL
1
2
1.01
(1)
(1)
3
7
8
9
14
3.3 V
1.02
PB5
57
AIN11
–
SSI2Fss
–
T1CCP1
CAN0Tx
–
–
1.03
PB0
45
–
U1Rx
–
–
T2CCP0
–
–
–
1.04
PB1
46
–
U1Tx
–
–
T2CCP1
–
–
–
1.05
PE4
59
AIN9
U5Rx
–
I2C2SCL
–
CAN0Rx
–
–
1.06
PE5
60
AIN8
U5Tx
–
I2C2SDA
–
CAN0Tx
–
–
1.07
PB4
58
AIN10
–
SSI2Clk
–
T1CCP0
CAN0Rx
–
–
1.08
PA5
22
–
–
SSI0Tx
–
–
–
–
–
1.09
PA6
23
–
–
–
I2C1SCL
–
–
–
–
1.10
PA7
24
–
–
–
I2C1SDA
–
–
–
–
Shaded cells indicate configuration for compatibility with the MSP430 LaunchPad.
Table 2-4. J2 Connector (1)
J2 Pin
GPIO
Stellaris
Pin
GPIOPCTL Register Setting
GPIOAMSEL
1
2
2.01
(2)
(3)
10
7
8
9
14
2.02
PB2
47
–
–
–
I2C0SCL
T3CCP0
–
–
–
2.03
PE0
9
AIN3
U7Rx
–
–
–
–
–
–
2.04
PF0
28
–
U1RTS
SSI1Rx
CAN0Rx
T0CCP0
NMI
C0o
–
2.05
(1)
3
GND
RESET
2.06 (2)
PB7
4
–
–
SSI2Tx
–
T0CCP1
–
–
–
2.07 (3)
PB6
1
–
–
SSI2Rx
–
T0CCP0
–
–
–
2.08
PA4
21
–
–
SSI0Rx
–
–
–
–
–
2.09
PA3
20
–
–
SSI0Fss
–
–
–
–
–
2.10
PA2
19
–
–
SSI0Clk
–
–
–
–
–
Shaded cells indicate configuration for compatibility with the MSP430 LaunchPad.
J2.06 (PB7) is also connected via a 0-Ω resistor to J3.04 (PD1).
J2.07 (PB6) is also connected via a 0-Ω resistor to J3.03 (PD0).
Hardware Description
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Functional Description
www.ti.com
Table 2-5. J3 Connector
J3 Pin
GPIO
Stellaris
Pin
GPIOPCTL Register Setting
GPIOAMSEL
1
2
3.01
(2)
3
7
8
9
14
5.0 V
3.02
(1)
(1)
GND
3.03
PD0
61
AIN7
SSI3Clk
SSI1Clk
I2C3SCL
WT2CCP0
–
–
–
3.04
PD1
62
AIN6
SSI3Fss
SSI1Fss
I2C3SDA
WT2CCP1
–
–
–
3.05
PD2
63
AIN5
SSI3Rx
SSI1Rx
–
WT3CCP0
–
–
–
3.06
PD3
64
AIN4
SSI3Tx
SSI1Tx
–
WT3CCP1
–
–
–
3.07
PE1
8
AIN2
U7Tx
–
–
–
–
–
–
3.08
PE2
7
AIN1
–
–
–
–
–
–
–
3.09
PE3
6
AIN0
–
–
–
–
–
–
–
3.10 (2)
PF1
29
–
U1CTS
SSI1Tx
–
T0CCP1
–
C1o
TRD1
8
9
Shaded cells indicate configuration for compatibility with the MSP430 LaunchPad.
Not recommended for BoosterPack use. This signal tied to on-board function via a 0-Ω resistor.
Table 2-6. J4 Connector
(1)
GPIOPCTL Register Setting
J4 Pin
GPIO
Stellaris
Pin
GPIOAMSEL
4.01 (1)
PF2
30
–
SSI1Clk
4.02 (1)
PF3
31
–
SSI1Fs
4.03
PB3
48
–
4.04
PC4
16
C1–
U4Rx
U1Rx
WT0CCP0
U1RTS
4.05
PC5
15
C1+
U4Tx
U1Tx
WT0CCP1
U1CTS
4.06
PC6
14
C0+
U3Rx
WT1CCP0
4.07
PC7
13
C0–
U3Tx
WT1CCP1
4.08
PD6
53
–
U2Rx
WT5CCP0
4.09 (1)
PD7
10
–
U2Tx
WT5CCP1
4.10 (1)
PF4
5
–
1
2
3
7
14
T1CCP0
TRD0
CAN0Tx
T1CCP1
TRCLK
I2C0SDA
T3CCP1
NMI
T2CCP0
Not recommended for BoosterPack use. This signal tied to on-board function via a 0-Ω resistor.
Connectors J1 and J2 of the Stellaris LM4F120 LaunchPad BoosterPack XL Interface provide
compatibility with MSP430 LaunchPad BoosterPacks. Highlighted functions (shaded cells) in Table 2-3
through Table 2-5 indicate configuration for compatibility with the MSP430 LaunchPad.
A complete list of Stellaris BoosterPacks and Stellaris LaunchPad-compatible MSP430 BoosterPacks is
available at www.ti.com/stellaris-launchpad.
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Hardware Description
11
Power Management
2.2
www.ti.com
Power Management
2.2.1 Power Supplies
The Stellaris LaunchPad can be powered from one of two power sources:
• On-board Stellaris ICDI USB cable (Debug, Default)
• USB device cable (Device)
The POWER SELECT switch (SW3) is used to select one of the two power sources. Select only one
source at a time.
2.2.2 Hibernate
The Stellaris LaunchPad provides an external 32.768-kHz crystal (Y1) as the clock source for the
LM4F120H5QR Hibernation module clock source. The current draw while in Hibernate mode can be
measured by making some minor adjustments to the Stellaris LaunchPad. This procedure is explained in
more detail later in this section.
The conditions that can generate a wake signal to the Hibernate module on the Stellaris LaunchPad are
waking on a Real-time Clock (RTC) match and/or waking on assertion of the WAKE pin. (1) The second
user switch (SW2) is connected to the WAKE pin on the microcontroller. The WAKE pin, as well as the
VDD and HIB pins, are easily accessible through breakout pads on the Stellaris LaunchPad. See the
appended schematics for details.
There is no external battery source on the Stellaris LaunchPad Hibernation module, which means the
VDD3ON power control mechanism should be used. This mechanism uses internal switches to remove
power from the Cortex-M4F processor as well as to most analog and digital functions while retaining I/O
pin power.
To measure the Hibernation mode current or the Run mode current, the VDD jumper that connects the 3.3
V pin and the MCU_PWR pin must be removed. See the complete schematics (appended to this
document) for details on these pins and component locations. An ammeter should then be placed
between the 3.3 V pin and the MCU_PWR pin to measure IDD (or IHIB_VDD3ON). The LM4F120H5QR
microcontroller uses VDD as its power source during VDD3ON Hibernation mode, so IDD is the Hibernation
mode (VDD3ON mode) current. This measurement can also be taken during Run mode, which measures
IDD the microcontroller running current.
2.2.3 Clocking
The Stellaris LaunchPad uses a 16.0-MHz crystal (Y2) to complete the LM4F120H5QR microcontroller
main internal clock circuit. An internal PLL, configured in software, multiples this clock to higher
frequencies for core and peripheral timing.
The Hibernation module is clocked from an external 32.768-KHz crystal (Y1).
2.2.4 Reset
The RESET signal into the LM4F120H5QR microcontroller connects to the RESET switch and to the
Stellaris ICDI circuit for a debugger-controlled reset.
External reset is asserted (active low) under any of three conditions:
• Power-on reset (filtered by an R-C network)
• RESET switch held down
• By the Stellaris ICDI circuit when instructed by the debugger (this capability is optional, and may not be
supported by all debuggers)
spacer
spacer
(1)
12
If the board does not turn on when you connect it to a power source, the microcontroller might be in Hibernate mode (depending on the
programmed application). You must satisfy one of the programmed wake conditions and connect the power to bring the microcontroller
out of Hibernate mode and turn on the board.
Hardware Description
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Stellaris In-Circuit Debug Interface (ICDI)
www.ti.com
2.3
Stellaris In-Circuit Debug Interface (ICDI)
The Stellaris LaunchPad evaluation board comes with an on-board Stellaris In-Circuit Debug Interface
(ICDI). The Stellaris ICDI allows for the programming and debug of the LM4F120H5QR using the LM
Flash Programmer and/or any of the supported tool chains. Note that the Stellaris ICDI supports only
JTAG debugging. An external debug interface can be connected for Serial Wire Debug (SWD) and SWO
(trace).
Table 2-7 shows the pins used for JTAG and SWD. These signals are also mapped out to easily
accessible breakout pads and headers on the board.
Table 2-7. Stellaris In-Circuit Debug Interface (ICDI)
Signals
GPIO Pin
Pin Function
PC0
TCK/SWCLK
PC1
TMS/SWDIO
PC2
TDI
PC3
TDO/SWO
2.3.1 Virtual COM Port
When plugged in to a PC, the device enumerates as a debugger and a virtual COM port. Table 2-8 shows
the connections for the COM port to the pins on the microcontroller.
Table 2-8. Virtual COM Port Signals
GPIO Pin
Pin Function
PA0
U0RX
PA1
U0TX
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Hardware Description
13
Chapter 3
SPMU289C – August 2012 – Revised September 2013
Software Development
This chapter provides general information on software development as well as instructions for Flash
memory programming.
3.1
Software Description
The StellarisWare software provided with the Stellaris LaunchPad provides access to all of the peripheral
devices supplied in the design. The Stellaris Peripheral Driver Library is used to operate the on-chip
peripherals as part of StellarisWare.
StellarisWare includes a set of example applications that use the StellarisWare Peripheral Driver Library.
These applications demonstrate the capabilities of the LM4F120H5QR microcontroller, as well as provide
a starting point for the development of the final application for use on the Stellaris LaunchPad evaluation
board.
3.2
Source Code
The complete source code including the source code installation instructions are provided at
www.ti.com/stellaris-launchpad. The source code and binary files are installed in the DriverLib tree.
3.3
Tool Options
The source code installation includes directories containing projects and/or makefiles for the following toolchains:
• Keil ARM RealView® Microcontroller Development System
• IAR Embedded Workbench for ARM
• Sourcery CodeBench
• Texas Instruments' Code Composer Studio™ IDE
Download evaluation versions of these tools from www.ti.com/stellaris. Due to code size restrictions, the
evaluation tools may not build all example programs. A full license is necessary to re-build or debug all
examples.
Instructions on installing and using each of the evaluation tools can be found in the Quickstart guides (for
example, Quickstart-Keil, Quickstart-IAR) which are available for download from the evaluation kit section
of the TI website at www.ti.com/stellaris.
For detailed information on using the tools, see the documentation included in the tool chain installation or
visit the respective web site of the tool supplier.
14
Software Development
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Programming the Stellaris LaunchPad Evaluation Board
www.ti.com
3.4
Programming the Stellaris LaunchPad Evaluation Board
The Stellaris LaunchPad software package includes pre-built binaries for each of the example
applications. If you have installed StellarisWare to the default installation path of C:\StellarisWare, you can
find the example applications in C:\StellarisWare\boards\ek-lm4f120xl. The on-board Stellaris ICDI is used
with the Stellaris LM Flash Programmer tool to program applications on the Stellaris LaunchPad.
Follow these steps to program example applications into the Stellaris LaunchPad evaluation board using
the Stellaris ICDI:
1. Install LM Flash Programmer on a PC running Microsoft® Windows®.
2. Switch the POWER SELECT switch to the right for Debug mode.
3. Connect the USB-A cable plug to an available port on the PC and the Micro-B plug to the Debug USB
port on the board.
4. Verify that the POWER LED D4 on the board is lit.
5. Run the LM Flash Programmer.
6. In the Configuration tab, use the Quick Set control to select the EK-LM4F120XL evaluation board.
7. Move to the Program tab and click the Browse button. Navigate to the example applications directory
(the default location is C:\StellarisWare\boards\ek-lm4f120xl\).
8. Each example application has its own directory. Navigate to the example directory that you want to
load and then into the directory which contains the binary (*.bin) files. Select the binary file and click
Open.
9. Set the Erase Method to Erase Necessary Pages, check the Verify After Program box, and check
Reset MCU After Program.
Program execution starts once the Verify process is complete.
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Software Development
15
Chapter 4
SPMU289C – August 2012 – Revised September 2013
References, PCB Layout, and Bill of Materials
4.1
References
In
•
•
•
•
addition to this document, the following references are available for download at www.ti.com/stellaris:
Stellaris LM4F120H5QR Microcontroller Data Sheet (literature number SPMS294).
StellarisWare Driver Library. Available for download at www.ti.com/tool/sw-drl.
StellarisWare Driver Library User’s Manual, publication SW-DRL-UG (literature number SPMU019).
TPS73633 Low-Dropout Regulator with Reverse Current Protection Data Sheet (literature number
SBVS038)
• TLV803 Voltage Supervisor Data Sheet (literature number SBVS157)
• Texas Instruments’ Code Composer Studio IDE website: www.ti.com/ccs
Additional support:
• RealView MDK (www.keil.com/arm/rvmdkkit.asp)
• IAR Embedded Workbench (www.iar.com).
• Sourcery CodeBench development tools (www.codesourcery.com/gnu_toolchains/arm).
16
References, PCB Layout, and Bill of Materials
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Component Locations
www.ti.com
4.2
Component Locations
Plots of the top-side component locations are shown in Figure 4-1 and the board dimensions are shown in
Figure 4-2.
Figure 4-1. Stellaris LaunchPad Component Locations (Top View)
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
References, PCB Layout, and Bill of Materials
Copyright © 2012–2013, Texas Instruments Incorporated
17
Bill of Materials (BOM)
www.ti.com
Figure 4-2. Stellaris LaunchPad Dimensions
NOTE: Units are in mils (one thousandth of an inch): 1 mil = 0.001 inch (0.0254 mm).
4.3
Bill of Materials (BOM)
Table 4-1 shows the bill of materials for the EK-LM4F120XL evaluation board.
Table 4-1. EK-LM4F120 Bill of Materials
Item
18
Ref Des
Qty
Description
Manufacturer
Manufacturer Part No
1
C1-2, C7, C12, C14
5
Capacitor, 0402, X5R, 10 V, Low
ESR
Johanson Dielectrics
Inc
100R07X105KV4T
2
C25-26, C31-32
4
Capacitor, 10 pF, 50 V, 5%,
NPO/COG, 0402
Murata
GRM1555C1H100JZ01D
3
C28-29
2
Capacitor, 24 pF, 50 V, 5%,
NPO/COG, 0402
TDK
C1005C0G1H240J
4
C3, C5, C8, C15,
C18-19, C21
7
Capacitor, 0.01 μF 25 V, 10%
0402 X7R
Taiyo Yuden
TMK105B7103KV-F
5
C4, C6, C10-11, C17,
C20, C23-24
8
Capacitor, 0.1 μF 16 V, 10% 0402
X7R
Taiyo Yuden
EMK105B7104KV-F
6
C9, C22
2
Capacitor, 2.2 μF, 16 V, 10%,
0603, X5R
Murata
GRM188R61C225KE15D
7
D1
1
LED, Tri-Color RGB, 0404 SMD
Common Anode
Everlight
18-038/RSGHBHC1-S02/2T
8
D2
1
Diode, Dual Schottky, SC70,
BAS70 Common Cathode
Diodes Inc
BAS70W-05-7-F
9
D4
1
LED, Green 565 nm, Clear 0805
SMD
Lite-On
LTST-C171GKT
10
H24
1
Header, 1x2, 0.100, T-Hole,
Vertical Unshrouded, 0.220 Mate
3M
961102-6404-AR
FCI
68001-102HLF
11
H25
1
Jumper, 0.100, Gold, Black,
Closed
Sullins
SPC02SYAN
References, PCB Layout, and Bill of Materials
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Bill of Materials (BOM)
www.ti.com
Table 4-1. EK-LM4F120 Bill of Materials (continued)
Item
Ref Des
Qty
Description
Manufacturer
Manufacturer Part No
12
J1, J4
2
Header, 2x10, T-Hole Vertical
unshrouded stacking
Samtec
SSW-110-23-S-D
13
J9, J11
2
USB Connectors Micro B Recept
RA SMT BTTM MNT
Hirose
ZX62-B-5PA
14
Q1-3
3
NPN SC70 pre-biased
Diodes Inc
DTC114EET1G
15
R1-2, R9-16, R20,
R26
12
Resistor, 0 Ω 1/10W 0603 SMD
Panasonic
ERJ-3GEY0R00V
16
R3-5, R8, R27
5
Resistor, 330 Ω, 1/10W, 5%, 0402
Yageo
RC0402FR-07330RL
17
R,6 R17-19, R21-23,
R28
8
Resistor, 10 kΩ, 1/10W, 5%, 0402
Thick Film
Yageo
RC0402FR-0710KL
18
R7, R31
2
Resistor, 1 MΩ 1/10W, 5%, 0402
RΩ
MCR01MRTF1004
19
RESET SW1, SW2
3
Switch, Tact 6 mm SMT, 160gf
Omron
B3S-1000
20
SW3
1
Switch, DPDT, SMT 300 mA × 2 at C K Components
6V
JS202011SCQN
21
U1, U2
2
Stellaris MCU
LM4F120H5QRFIGA3
LM4F120H5QRFIG
22
U4
1
IC, Single Voltage Supervisor, 5 V, Texas Instruments
DBV
TLV803MDBZR
23
U8
1
Regulator, 3.3 V, 400 mA, LDO
Texas Instruments
TPS73633DRBT
24
Y1
1
Crystal, 32.768 kHz Radial Can
Abracon
AB26TRB-32.768KHZ- T
25
Y2, Y5
2
Crystal, 16.00 MHz 5.0x3.2mm
SMT
NDK
NX5032GA-16.000000 MHz
Abracon
ABM3-16.000 MHz-B2- T
Texas Instruments
PCB Do Not Populate List
(Shown for information only)
26
C13, C34
2
Capacitor, 0.1 μF 16 V, 10% 0402
X7R
Taiyo Yuden
EMK105B7104KV-F
27
R24
1
Resistor, 330 Ω, 1/10W, 5%, 0402
Yageo
RC0402FR-07330RL
28
R30
1
Resistor, 0 Ω 1/10W 0603 SMD
Panasonic
ERJ-3GEY0R00V
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
References, PCB Layout, and Bill of Materials
Copyright © 2012–2013, Texas Instruments Incorporated
19
Appendix A
SPMU289C – August 2012 – Revised September 2013
Schematics
This section contains the complete schematics for the Stellaris LaunchPad board.
• Microcontroller, USB, Expansion, Buttons, and LED
• Power Management
• Stellaris In-Circuit Debug Interface
20
Schematics
SPMU289C – August 2012 – Revised September 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Microcontroller, USB, Expansion, Buttons, and
LED
9
8
7
6
59
60
VB
1
D+
D2
3
G
PF0
PF1
PF2
PF3
PF4
PD0
PD1
PD2
PD3
0
9
8
ID
PE0
PE1
PE2
PE3
PE4
PE5
61
62
63
64
43
44
53
10
J9
CON-USB-MICROB
5
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
7
6
R14
+USB_VBUS
+USB_VBUS
USB_DM
USB_DP
28
29
30
31
5
PD6
PD7
PF0
PF1
PF2
PF3
PF4
10k
PE0
PE1
PE2
PE3
PE4
PE5
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
GPIO
45
46
47
48
58
57
1
4
R6
PC4
PC5
PC6
PC7
52
51
50
49
16
15
14
13
DEBUG_PC0/TCK/SWCLK
DEBUG_PC1/TMS/SWDIO
DEBUG_PC2/TDI
DEBUG_PC3/TDO/SWO
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
0
USB_DP
R15
USB_DM
J1 and J2 provide compatability with
1M
PA2
PA3
PA4
PA5
PA6
PA7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
4
U1-A
17
18
19
20
21
22
23
24
PA0/U0RX_VCP_TXD
PA1/U0TX_VCP_RXD
GPIO
R7
DEBUG/VCOM
Booster Packs designed for MSP430 Launchpad
Used for VBUS detection when
J3 and J4 sit 100 mils inside J1 and J2 to provide
configured as a self-powered USB Device
extended functions specific to this board.
LM4F120
See the board user manual for complete table of pin mux functions
GPIO
0
0
0
0
0
R1
R2
R11
R12
R13
+3.3V
USR_SW2
LED_R
LED_B
LED_G
USR_SW1
J1
0
PD0
PD1
PB6
R9
0
PB7
R10
J2
1
2
3
4
5
6
7
8
9
10
PB5
PB0
PB1
PE4
PE5
PB4
PA5
PA6
PA7
1
2
3
4
5
6
7
8
9
10
PB2
PE0
PF0
PB7
PB6
PA4
PA3
PA2
TARGETRST
CON_110_100
CON_110_100
+VBUS
SW1
USR_SW1
J3
R3
C
LED_R
Q1
DTC114EET1G
B
E
+VBUS
SW2
USR_SW2
D1
R5
C
LED_G
330
Q3
DTC114EET1G
B
2
3
4
R
G
B
A
1
RGB_LED_0404_COMA
J4
1
2
3
4
5
6
7
8
9
10
330
PD0
PD1
PD2
PD3
PE1
PE2
PE3
PF1
PF2
PF3
PB3
PC4
PC5
PC6
PC7
PD6
PD7
PF4
1
2
3
4
5
6
7
8
9
10
CON_110_100
CON_110_100
R8
WAKE
330
E
R4
C
LED_B
330
Q2
DTC114EET1G
B
E
DESIGNER
REVISION
DATE
DGT
0.1
8/23/2012
TEXAS INSTRUMENTS
STELLARIS R MICROCONTROLLERS
PROJECT
108 WILD BASIN ROAD, SUITE 350
AUSTIN TX, 78746
Stellaris Launchpad
DESCRIPTION
www.ti.com/stellaris
Microcontroller, USB, Expansion, Buttons and LED
FILENAME
EK-LM4F120XL Rev A.sch
PART NO.
EK-LM4F120XL
SHEET
1 OF 3
Power Management
+MCU_PWR
RESET
R28
10k
H20
H24 and H25 installed as a single 1x2
RESET
+USB_VBUS
header on 100 mil center with jumper
TARGETRST
H18
Power Select
C13
0.1uF
OMIT
+VBUS
SW3
U1-B
2
38
3
RESET
WAKE
41
OSC1
40
OSC0
6
5
34
XOSC0
35
GNDX
36
XOSC1
C28
24pF
Y2
16MHz
C29
24pF
0
R26
4
3
C31
10pF
+3.3V
+VBUS
+3.3V 400mA Regulator
H22
32.768Khz
Y1
VBAT
VDDA
H25
+3.3V
33
0
R30
OMIT
HIB
37
2
11
VDD
26
VDD
42
VDD
54
VDD
GNDA
12
GND
27
GND
39
GND
55
GND
C32
10pF
HIB
32
H1
1
H17 H23
+MCU_PWR
H24
WAKE
25
VDDC
56
VDDC
LM4F120
C3
C4
C5
C6
C8
C7
0.01uF
0.1uF
0.01uF
0.1uF
0.01uF
1.0uF
H2
H19
H21
1M
R31
+ICDI_VBUS
C10
0.1uF
+MCU_VDDC
C11
0.1uF
C12
C22
2.2uF
1.0uF
U8
TPS73633DRB
3
C18
0.01uF
Green
1.0uF
1
9
4
C14
NR
PAD
R27
OUT
EN
GND
330
IN
5
D4
8
H11
H13
H12
H10
+VBUS
+3.3V
R17
10k
D2
TLV803
RESET 2
3
VDD
GND 1
A1
3
K
A2
TARGETRST
ICDI_RST
U4
DESIGNER
REVISION
DATE
DGT
0.1
8/23/2012
TEXAS INSTRUMENTS
STELLARIS R MICROCONTROLLERS
PROJECT
108 WILD BASIN ROAD, SUITE 350
AUSTIN TX, 78746
Stellaris Launchpad
DESCRIPTION
www.ti.com/stellaris
Power Management
FILENAME
EK-LM4F120XL Rev A.sch
PART NO.
EK-LM4F120XL
SHEET
2 OF 3
Stellaris In-Circuit Debug Interface (ICDI)
PA1/U0TX_VCP_RXD
PA0/U0RX_VCP_TXD
+MCU_PWR
Stellaris In-Circuit Debug Interface (ICDI)
DEBUG/VCOM
+3.3V
52
51
50
49
16
15
14
13
+3.3V
R22
10k
9
8
7
6
59
60
ICDI_TCK
ICDI_TMS
ICDI_TDI
ICDI_TDO
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PE0
PE1
PE2
PE3
PE4
PE5
PF0
PF1
PF2
PF3
PF4
45
46
47
48
58
57
1
4
61
62
63
64
43
44
53
10
28
29
30
31
5
R24
330
VB
1
D-
2
DEBUG_PC3/TDO/SWO
D+
3
ID
4
DEBUG_PC1/TMS/SWDIO
DEBUG_PC0/TCK/SWCLK
CON-USB-MICROB
J11
H14
EXTDBG
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
6
7
TARGETRST
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
0
R16
G
5
8
9
17
18
19
20
21
22
23
24
DEBUG_PC0/TCK/SWCLK
DEBUG_PC1/TMS/SWDIO
DEBUG_PC3/TDO/SWO
DEBUG_PC2/TDI
R21
10k
+ICDI_VBUS
U2-A
R23
10k
H15
R18
10k
LM4F120
+3.3V
R19
10k
ICDI_RST
C34
0.1uF
OMIT
ICDI JTAG
+3.3V
U2-B
38
RESET
WAKE
34
XOSC0
35
GNDX
36
XOSC1
0
R20
41
OSC1
40
OSC0
Y5
16MHz
3
C25
10pF
C26
10pF
HIB
VBAT
VDDA
33
ICDI_TCK
37
ICDI_TMS
+3.3V
5
4
3
2
1
6
7
8
9
10
ICDI_TDO
ICDI_TDI
ICDI_RST
2
11
VDD
26
VDD
42
VDD
54
VDD
GNDA
12
GND
27
GND
39
GND
55
GND
J5
32
TC2050-IDC-NL
C15
C17
C19
C20
C21
C1
0.01uF
0.1uF
0.01uF
0.1uF
0.01uF
1.0uF
25
VDDC
56
VDDC
LM4F120
C23
0.1uF
C24
0.1uF
C2
1.0uF
C9
2.2uF
DESIGNER
REVISION
DATE
DGT
0.1
8/23/2012
TEXAS INSTRUMENTS
STELLARIS R MICROCONTROLLERS
PROJECT
108 WILD BASIN ROAD, SUITE 350
AUSTIN TX, 78746
Stellaris Launchpad
DESCRIPTION
www.ti.com/stellaris
SStellaris In Circuit Debug Interface
FILENAME
EK-LM4F120XL Rev A.sch
PART NO.
EK-LM4F120XL
SHEET
3 OF 3
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of EVMs for RF Products in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,
CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine
and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable
safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to
perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
