Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
INA1x9-Q1 Automotive-Grade, High-Side, Current-Output, Current-Shunt Monitor
1 Features
3 Description
•
•
The INA139-Q1 and INA169-Q1 (INA1x9-Q1) are
high-side, unidirectional, current shunt monitors. Wide
input common-mode voltage range, high-speed, low
quiescent current, and TSSOP-8 packaging enable
use in a variety of applications.
1
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: −40°C to 125°C
Ambient Operating Temperature Range
– Device HBM ESD Classification Level 2
– Device CDM ESD Classification Level C6
Complete Unidirectional High-Side Current
Measurement Circuit
Wide Supply and Common-Mode Ranges
– INA139-Q1: 2.7 V to 40 V
– INA169-Q1: 2.7 V to 60 V
Independent Supply and Input Common-Mode
Voltages
Single Resistor Gain Set
Low Quiescent Current (60 μA Typical)
Wide Temperature Range: –40°C to +125°C
Package: TSSOP-8
Both the INA139-Q1 and INA169-Q1 are available in
a TSSOP-8 package, and are specified for the –40°C
to +125°C temperature range.
Device Information(1)
PART NUMBER
INA139-Q1
PACKAGE
TSSOP (8)
INA169-Q1
BODY SIZE (NOM)
4.40 mm × 3.00 mm
(1) For all available packages, see the package option addendum
at the end of the data sheet.
2 Applications
•
•
•
•
The device converts a differential input voltage to a
current output. This current is converted back to a
voltage with an external load resistor that sets any
gain from 1 to over 100. Although designed for
current shunt measurement, the circuit invites
creative applications in measurement and level
shifting.
Electric Power Steering (EPS) Systems
Body Control Modules
Brake Systems
Electronic Stability Control (ESC) Systems
Typical Application Circuit
Up to 60 V
VIN+
1 kW
VIN–
1 kW
VO = ISRSRL / 1 kΩ
RL
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
3
3
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
7.1 Overview ................................................................... 8
7.2 Functional Block Diagram ......................................... 8
7.3 Feature Description................................................... 9
7.4 Device Functional Modes.......................................... 9
8
Application and Implementation .......................... 9
8.1 Application Information.............................................. 9
8.2 Typical Applications ................................................ 11
9 Power Supply Recommendations...................... 18
10 Layout................................................................... 18
10.1 Layout Guidelines ................................................. 18
10.2 Layout Example .................................................... 18
11 Device and Documentation Support ................. 19
11.1
11.2
11.3
11.4
11.5
11.6
Related Documentation .......................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
19
19
19
19
19
19
12 Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (May 2011) to Revision F
Page
•
Added Device Information, ESD Ratings, Recommended Operating Conditions, and Thermal Information tables,
and Feature Description, Application and Implementation, Power Supply Recommendations, Layout, Device and
Documentation Support, and Mechanical, Packaging, and Orderable Information sections ................................................. 1
•
Added new automotive qualification features bullet, and deleted old bullet........................................................................... 1
•
Changed Applications bullets ................................................................................................................................................. 1
•
Changed text in Description section ....................................................................................................................................... 1
•
Changed all figures to show correct device names; added -Q1............................................................................................. 1
•
Added pin names to all figures and removed all pin numbers ............................................................................................... 1
•
Deleted Ordering Information table; information available in the Package Option Addendum at the end of this data sheet 3
•
Deleted lead temperature and thermal resistance from Absolute Maximum Ratings table; see new Thermal
Information table for thermal resistance values...................................................................................................................... 3
•
Changed RθJA value................................................................................................................................................................ 4
•
Changed VS to V+ throughout data sheet for consistency ..................................................................................................... 5
•
Changed ROUT in Electrical Characteristics table to RL for consistency ................................................................................. 5
•
Changed RL from 125 kΩ to 25 kΩ in condition line of Typical Characteristics section......................................................... 6
•
Changed VIN to VSENSE in Figure 4 ......................................................................................................................................... 6
•
Changed VS to RS when describing shunt resistor in Operation section................................................................................ 9
•
Changed Figure 9; deleted incorrect pin numbers, and moved embedded table to outside of figure ................................. 10
•
Changed Figure 10 ............................................................................................................................................................... 11
•
Changed Figure 14 to show correct pin names, deleted incorrect pin numbers, and added missing division line in
output offset equation ........................................................................................................................................................... 14
•
Changed Figure 15 ............................................................................................................................................................... 15
2
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
5 Pin Configuration and Functions
PW Package
8-Pin TSSOP
Top View
1
8
V+
IN+
2
7
NC
NC
3
6
OUT
GND
4
5
NC
V
V
IN–
Pin Functions
PIN
NAME
NO.
GND
I/O
DESCRIPTION
4
—
Ground
3, 5, 7
—
Not connected internally
OUT
6
O
Output current
V+
8
I
Power supply voltage
VIN+
2
I
Positive input voltage
VIN-
1
I
Negative input voltage
NC
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
INA139-Q1
Supply, V+
Voltage
(1)
INA169-Q1
Common mode
Analog inputs, VIN+, VIN–
UNIT
60
V
–0.3
75
V
–0.3
60
V
INA169-Q1
–0.3
75
V
–40
2
V
Analog output, OUT
–0.3
40
V
Operating, TA
–55
125
°C
150
°C
150
°C
Junction, TJ
Storage, Tstg
(1)
MAX
INA139-Q1
Differential, (VIN+) – (VIN–)
Temperature
MIN
–0.3
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002
(1)
Charged-device model (CDM), per AEC Q100-011
±2000
±1000
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
3
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply voltage, V+
Common mode voltage
MIN
NOM
MAX
INA139-Q1
2.7
5
40
V
INA169-Q1
2.7
5
60
V
INA139-Q1
2.7
12
40
V
INA169-Q1
2.7
12
60
V
125
°C
Operating temperature, TA
–40
UNIT
6.4 Thermal Information
INA1x9-Q1
THERMAL METRIC (1)
PW (TSSOP)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
179.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
62.6
°C/W
RθJB
Junction-to-board thermal resistance
107.7
°C/W
ψJT
Junction-to-top characterization parameter
7
°C/W
ψJB
Junction-to-board characterization parameter
106
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
6.5 Electrical Characteristics
at TA = −40°C to +125°C, V+ = 5 V, VIN+ = 12 V, and RL = 25 kΩ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
INA139-Q1
MIN
INA169-Q1
TYP
MAX
100
500
MIN
TYP
MAX
100
500
UNIT
INPUT
Full-scale sense voltage
Common-mode rejection
VSENSE = VIN+ − VIN−
VIN+ = 2.7 V to 40 V, VSENSE = 50 mV
100
VIN+ = 2.7 V to 60 V, VSENSE = 50 mV
100
Offset voltage (1) RTI
±0.2
Offset voltage vs temperature
Offset voltage vs power supply
(V+)
mV
115
±2
±0.2
1
VIN+ = 2.7 V to 40 V, VSENSE = 50 mV
±2
mV
μV/°C
1
0.5
10
VIN+ = 2.7 V to 60 V, VSENSE = 50 mV
0.1
Input bias current
dB
120
10
μV/V
10
μA
10
OUTPUT
Transconductance
VSENSE = 10 mV to 150 mV
Transconductance versus
temperature
VSENSE = 100 mV
Nonlinearity error
VSENSE = 10 mV to 150 mV
Total output error
VSENSE = 100 mV
980
1000
1020
10
980
1000
μA/V
1020
10
±0.01%
±0.2%
±0.01%
±0.5%
±2%
±0.5%
Output impedance
1 || 5
nA/°C
±0.2%
±2%
1 || 5
GΩ || pF
Voltage output swing to power
supply (V+)
(V+) − 0.9
(V+) − 1.2
(V+) − 0.9
(V+) − 1.2
V
Voltage output swing to
common mode, VCM
VCM − 0.6
VCM − 1
VCM − 0.6
VCM − 1
V
FREQUENCY RESPONSE
Bandwidth
Settling time (0 1%)
RL = 10 kΩ
440
440
RL = 20 kΩ
220
220
5 V step, RL = 10 kΩ
2.5
2.5
5 V step, RL = 20 kΩ
5
5
20
20
pA/√Hz
7
7
nA RMS
kHz
μs
NOISE
Output-current noise density
Total output-current noise
BW = 100 kHz
POWER SUPPLY
Quiescent current
(1)
VSENSE = 0 V, IO = 0 mA
60
125
60
125
μA
Defined as the amount of input voltage, VSENSE, to drive the output to zero.
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
5
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
6.6 Typical Characteristics
at TA = 25°C, V+ = 5 V, VIN+ = 12 V, and RL = 25 kΩ (unless otherwise noted)
Common-Mode Rejection (dB)
= 100 kW
Gain (dB)
= 10 kW
= 1 kW
Figure 2. Common-Mode Rejection vs Frequency
Figure 1. Gain vs Frequency
VSENSE = (VIN+ – VIN–)
PSR (dB)
Total Output Error (%)
–55°C
150°C
–
25°C
–
–
VSENSE (mV)
Figure 3. Power-Supply Rejection vs Frequency
Total Output Error (%)
Quiescent Current (mA)
Figure 4. Total Output Error vs VIN
Use the INA169-Q1 with (V+) > 40 V
Figure 5. Total Output Error vs Power-Supply Voltage
6
Submit Documentation Feedback
Figure 6. Quiescent Current vs Power-Supply Voltage
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
Typical Characteristics (continued)
at TA = 25°C, V+ = 5 V, VIN+ = 12 V, and RL = 25 kΩ (unless otherwise noted)
1.5 V
1V
0.5 V
0V
1V
2V
0V
0V
20 μs/div
10 μs/div
Figure 7. Step Response
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Figure 8. Step Response
Submit Documentation Feedback
7
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
7 Detailed Description
7.1 Overview
The INA139-Q1 and INA169-Q1 devices (INA1x9-Q1) are comprised of a high voltage, precision operational
amplifier, precision thin film resistors trimmed in production to an absolute tolerance and a low noise output
transistor. The INA1x9-Q1 are powered from a single power supply, and the input voltages can exceed the
power-supply voltage. The INA1x9-Q1 are ideal for measuring small differential voltages, such as those
generated across a shunt resistor in the presence of large, common-mode voltages. The Functional Block
Diagram illustrates the functional components within both the INA139-Q1 and INA169-Q1 devices.
7.2 Functional Block Diagram
VIN+
VIN±
V+
+
OUT
GND
8
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
7.3 Feature Description
7.3.1 Output Voltage Range
The output of the INA1x9-Q1 is a current that is converted to a voltage by the load resistor, RL. The output
current remains accurate within the compliance voltage range of the output circuitry. The shunt voltage and the
input common-mode and power-supply voltages limit the maximum possible output swing. The maximum output
voltage (VOUT MAX) compliance is limited by either Equation 1 and Equation 2, whichever is lower:
VOUT MAX = (V+) − 0.7 V − (VIN+ − VIN−)
(1)
VOUT MAX = VIN− − 0.5 V
(2)
or
7.3.2 Bandwidth
Measurement bandwidth is affected by the value of the load resistor, RL. High gain produced by high values of
RL yields a narrower measurement bandwidth (see the Typical Characteristics section). For the widest possible
bandwidth, keep the capacitive load on the output to a minimum. Reduction in bandwidth due to capacitive load
is shown in the Typical Characteristics.
If bandwidth limiting (filtering) is desired, add a capacitor can be added to the output (see Figure 12). This
capacitor does not cause instability.
7.4 Device Functional Modes
For proper operation, the INA1x9-Q1 must operate within the specified limits. Operating either device outside of
their specified power supply voltage range, or their specified common-mode range, results in unexpected
behavior, and is not recommended. Additionally, operating the output beyond the specified limits, with respect to
power supply voltage and input common-mode voltage, also produces unexpected results. See the Electrical
Characteristics for the device specifications.
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Operation
Figure 9 illustrates the basic circuit diagram for both the INA139-Q1 and INA169-Q1. Load current IS is drawn
from supply VP through shunt resistor RS. The voltage drop in shunt resistor RS is forced across RG1 by the
internal op amp, causing current to flow into the collector of Q1. External resistor RL converts the output current,
IO, to a voltage, VOUT, at the OUT pin. The transfer function for the INA1x9-Q1 is given by Equation 3:
IO = gm (VIN+ − VIN−)
where
•
where gm = 1000 μA/V.
(3)
In the circuit of Figure 9, the input voltage (VIN+ − VIN−) is equal to IS × RS and the output voltage (VOUT) is equal
to IO × RL. The transconductance (gm) of the INA1x9-Q1 is 1000 μA/V. The complete transfer function for the
current measurement amplifier in this application is given by Equation 4:
VOUT = (IS) (RS) (1000 μA/V) (RL)
(4)
The maximum differential input voltage for accurate measurements is 0.5 V, producing a 500-μA output current.
A differential input voltage of up to 2 V does not cause damage. Differential measurements (VIN+ and VIN− pins)
must be unipolar, with a more-positive voltage applied to the VIN+ pin. If a more-negative voltage is applied to
VIN+ pin, IO goes to zero, but no damage occurs.
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
9
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
Application Information (continued)
VP
Load Power Supply
2.7 V to 40 V(1)
V+ power can be common or
V+
independent of load supply.
2.7 V ≤ (V+) ≤ 40 V
(1)
Shunt
RS
VIN+
IS
VIN–
R G1
1 kΩ
Load
R G1
1 kΩ
Q1
OUT
INA139-Q1
+
IO
GND
RL
VO
–
Copyright © 2016, Texas Instruments Incorporated
(1)
Maximum VP and V+ voltage is 60 V with INA169-Q1.
Figure 9. Basic Circuit Connections
Table 1. Voltage Gains and Corresponding Load-Resistor Values
10
VOLTAGE GAIN
EXACT RL (kΩ)
NEAREST 1% RL (kΩ)
1
1
1
2
2
2
5
5
4.99
10
10
10
20
20
20
50
50
49
100
100
100
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
8.2 Typical Applications
The INA1x9-Q1 are designed for current-shunt measurement circuits, as shown in Figure 9, but the basic
function is useful in a wide range of circuitry. With a little creativity, many unforeseen uses are found in
measurement and level shifting circuits. A few ideas are illustrated in the following subsections.
8.2.1 Buffering Output to Drive an ADC
Digitize the output of the INA139-Q1 or INA169-Q1 devices using a 1-MSPS analog-to-digital converter (ADC).
IS
RS
VIN+
VIN±
R
+
OUT
ADC
OPA340
INA139-Q1
or
INA169-Q1
RL
GND
Buffer amplifier
drives ADC without
affecting gain
C
Figure 10. Buffering Output to Drive an ADC
8.2.1.1 Design Requirements
For this design example, use the input parameters shown in Table 2.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Supply voltage, V+
Common-mode voltage, VCM
5V
INA139-Q1: 2.7 V to 40 V
INA169-Q1: 2.7 V to 60 V
Full-scale shunt voltage, VSENSE
50 mV to 100 mV
Load resistor, RL
1 kΩ to 100 kΩ
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Selecting RS and RL
In Figure 10, the value chosen for the shunt resistor, RS, depends on the application and is a compromise
between small-signal accuracy and maximum permissible voltage loss in the measurement line. High values of
RS provide better accuracy at lower currents by minimizing the effects of offset, while low values of RS minimize
voltage loss in the supply line. For most applications, best performance is attained with an RS value that provides
a full-scale shunt voltage range of 50 mV to 100 mV. Maximum input voltage for accurate measurements is 500
mV.
Choose an RL that provides the desired full-scale output voltage. The output impedance of the INA1x9-Q1 OUT
pin is very high, permitting the use of RL values up to 100 kΩ with excellent accuracy. The input impedance of
any additional circuitry at the output must be much higher than the value of RL to avoid degrading accuracy.
Some ADCs have input impedances that significantly affect measurement gain. The input impedance of the A/D
converter can be included as part of the effective RL if its input can be modeled as a resistor to ground.
Alternatively, an op amp can be used to buffer the ADC input, as shown in Figure 10. The INA1x9-Q1 are current
output devices, and as such have an inherently large output impedance. The output currents from the amplifier
are converted to an output voltage using the load resistor, RL, connected from the amplifier output to ground. The
ratio of the load resistor value to that of the internal resistor value determines the voltage gain of the system.
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
11
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
In many applications, digitizing the output of the INA1x9-Q1 is required. Digitizing is accomplished by connecting
the output of the amplifier to an ADC. It is very common for an ADC to have a dynamic input impedance. If the
INA1x9-Q1 output is connected directly to an ADC input, the input impedance of the ADC is effectively connected
in parallel with gain setting resistor RL. This parallel impedance combination affects the gain of the system and
the impact on the gain is difficult to estimate accurately. A simple solution that eliminates the paralleling of
impedances, and simplifies the gain of the circuit is to place a buffer amplifier, such as the OPA340, between the
output of the INA1x9-Q1 and the input to the ADC.
Figure 10 illustrates this concept. Notice that a low-pass filter is placed between the OPA340 output and the
input to the ADC. The filter capacitor is required to provide any instantaneous demand for current required by the
input stage of the ADC. The filter resistor is required to isolate the OPA340 output from the filter capacitor in
order to maintain circuit stability. The values for the filter components vary according to the operational amplifier
used for the buffer and the particular ADC selected. More information regarding the design of the low-pass filter
is found in the TI Precision Design, 16 bit 1MSPS Data Acquisition Reference Design for Single-Ended
Multiplexed Applications, TIPD173.
Figure 11 shows the expected results when driving an ADC at 1 MSPS with and without buffering the INA1x9-Q1
output. Without the buffer, the high impedance of the INA1x9-Q1 reacts with the input capacitance and sampleand-hold capacitance of the ADC, and does not allow the sampled value to reach the correct final value before
the ADC is reset, and the next conversion starts. Adding the buffer amplifier significantly reduces the output
impedance driving the sample-and-hold circuitry, and allows for higher conversion rates.
8.2.1.3 Application Curve
Input to ADC (0.25 V/div)
with buffer
without Buffer
Time
Figure 11. Driving an ADC With and Without a Buffer
12
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
8.2.2 Output Filter
Filter the output of the INA139-Q1 or INA169-Q1 devices.
VIN–
VIN+
INA139-Q1
p RLCL
VO
OUT
GND
RL
CL
Figure 12. Output Filter
8.2.2.1 Design Requirements
For this design example, use the input parameters shown in Table 3.
Table 3. Design Parameters
DESIGN PARAMETER
Supply voltage, V+
Common-mode voltage, VCM
EXAMPLE VALUE
INA139-Q1: 0 V to 40 V
INA169-Q1: 0 V to 60 V
INA139-Q1: 0 V to 40 V
INA169-Q1: 0 V to 60 V
Full-scale shunt voltage, VSENSE
50 mV to 100 mV
Load resistor, RL
1 kΩ to 100 kΩ
8.2.2.2 Detailed Design Procedure
A low-pass filter can be formed at the output of the INA1x9-Q1 simply by placing a capacitor of the desired value
in parallel with the load resistor. First, determine the value of the load resistor needed to achieve the desired gain
by using Table 1. Next, determine the capacitor value that results in the desired cutoff frequency according to the
equation shown in Figure 12. Figure 13 shows the frequency response with different RL values and a fixed filter
capacitor.
8.2.2.3 Application Curve
= 100 kW
Gain (dB)
= 10 kW
= 1 kW
Figure 13. Gain vs Frequency
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
13
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
8.2.3 Offsetting the Output Voltage
For many applications using only a single power supply, the output voltage may have to be level shifted away
from ground when there is no load current flowing in the shunt resistor. Level shifting the output of the INA1x9Q1 is easily accomplished by one of two simple methods shown in Figure 14. Method (a) on the left-hand side of
Figure 14 illustrates a simple voltage divider method. This method is useful for applications that require the
output of the INA1x9-Q1 to remain centered with respect to the power supply at a zero load current through the
shunt resistor. Using this method, the gain is determined by the parallel combination of R1 and R2, while the
output offset is determined by the voltage divider ratio of R1 and R2, as shown in Figure 14(a). For applications
that require a fixed value of output offset independent of the power supply voltage, use current-source method
(b), shown on the right-hand side of Figure 14. With this method, a REF200 constant current source is used to
generate a constant output offset. Using his method, the gain is determined by RL, and the offset is determined
by the product of the value of the current source and RL.
VR
VIN+
VIN–
VIN+
R1
INA139-Q1
INA139-Q1
VO
OUT
VIN–
100 μA
RL
R2
Gain Set by R1 || R2
(VR)R2
R1 + R2
VO
OUT
Gain Set by RL
Output Offset = (100 μA)(RL)
(independent of V+)
Output Offset =
b) Using current source.
a) Using resistor divider.
Copyright © 2016, Texas Instruments Incorporated
Figure 14. Offsetting the Output Voltage
8.2.4 Bipolar Current Measurement
Configure the INA1x9-Q1 as shown in Figure 15 for applications where bidirectional current measurement is
required. Two INA1x9-Q1 devices are required; connect the inputs across the shunt resistor as shown in
Figure 15. A comparator, such as the TLV3201, is used to detect the polarity of the load current. The magnitude
of the load current is monitored across the resistor connected between ground and the connection labeled
Output. In this example, the 20-kΩ resistor results in a gain of 20 V/V. The 10-kΩ resistors connected in series
with the INA1x9-Q1 output current are used to develop a voltage across the comparator inputs. Two diodes are
required to prevent current flow into the INA1x9-Q1 output because only one device at a time provides current to
the Output connection of the circuit. The circuit functionality is illustrated in Figure 16.
14
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
±1-A
Load Curent
RS
100 m
VIN+
VIN±
VIN±
VIN+
Bus
Voltage
1k
5V
1k
1k
Load
Current
1k
V+
5V
V+
+
INA139-Q1
or
INA169-Q1
+
OUT
OUT
GND
GND
1N4148
INA139-Q1
or
INA169-Q1
1N4148
+
Sign
TLV3201
10 k
10 k
Output
20 k
Figure 15. Bipolar Current Measurement
8.2.4.1 Application Curve
Voltage
Load Current
Output
Sign
Time
Figure 16. Bipolar Current Measurement Results (Arbitrary Scale)
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
15
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
8.2.5 Bipolar Current Measurement Using Differential Input of the ADC
Use the INA1x9-Q1 with an ADC, such as the ADS7870, programmed for differential-mode operation; Figure 17
illustrates this configuration. In this configuration, the use of two INA138-Q1s or INA168-Q1s allows for
bidirectional current measurement. Depending on the polarity of the current, one of the INA devices provides an
output voltage, while the other INA device output is zero. In this way, the ADC reads the polarity of current
directly, without the need for additional circuitry.
RS
V+
VIN–
VIN+
VIN+
VIN–
5V
5V
5V
REFOUT BUFIN
REF
Digital
I/O
INA139-Q1
OUT
BUFOUT
BUF
INA139-Q1
GND
RL
25 kΩ
GND
OUT
RL
25 kΩ
PGIA
Mux
Clock
Divider
Oscillator
12-Bit
ADC
Serial
I/O
ADS7870
The ADC is programmed for differential input.
Depending on the polarity of the current, one INA139-Q1
provides an output voltage whereas the output of the other is zero.
Figure 17. Bipolar Current Measurement Using Differential Input of the ADC
16
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
8.2.6 Multiplexed Measurement Using Logic Signal for Power
Measure multiple loads as shown in Figure 18. In this configuration, each INA1x9-Q1 device is powered by the
digital I/O from the ADS7870. Multiplexing is achieved by switching on or off each desired I/O.
Other INA169-Q1s
Digital I/O on the ADS7870 provides power to
select the desired INA169-Q1. Diodes prevent
output current of an on INA169-Q1 from flowing
into an off INA169-Q1.
INA169-Q1
V+
5V
BUFOUT
REFOUT BUFIN
Digital
I/O
REF
BUF
INA169-Q1
V+
Mux
PGIA
12-Bit
ADC
1N4148
RL
Clock
Divider
Oscillator
Serial
I/O
ADS7870
Figure 18. Multiplexed Measurement Using Logic Signal for Power
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
17
INA139-Q1, INA169-Q1
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
www.ti.com
9 Power Supply Recommendations
The input circuitry of the INA1x9-Q1 can accurately measure beyond its power-supply voltage, V+. For example,
the V+ power supply can be 5 V, whereas the load power-supply voltage goes up to 36 V with the INA138-Q1, or
60 V with the INA168-Q1. However, the output voltage range of the OUT pin is limited by the lesser of the two
voltages (see the Output Voltage Range section). Place a 0.1-µF capacitor near the V+ pin on the INA1x9-Q1.
Additional capacitance may be required for applications with noisy supply voltages.
10 Layout
10.1 Layout Guidelines
Figure 9 shows the basic connection of the INA1x9-Q1. Connect input pins VIN+ and VIN− as closely as possible
to the shunt resistor to minimize any resistance in series with the shunt resistance. Output resistor RL is shown
connected between the OUT pin and ground. Best accuracy is achieved with the output voltage measured
directly across RL. Measuring directly across RL is especially important in high-current systems where load
current could flow in the ground connections and affect measurement accuracy.
No power-supply bypass capacitors are required for stability of the INA1x9-Q1. However, applications with noisy
or high-impedance power supplies may require decoupling capacitors to reject power-supply noise. Connect
bypass capacitors close to the device pins.
10.2 Layout Example
To Load
VIN-
Sense/Shunt
Resistor
INA139-Q1
INA169-Q1
V+
VIN+
NC
NC
OUT
GND
NC
Supply
Bypass
Capacitor
RL
To Bus Voltage
Via to Ground Plane
Via to Power Plane
Figure 19. Typical Layout Example
18
Submit Documentation Feedback
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
INA139-Q1, INA169-Q1
www.ti.com
SGLS185F – SEPTEMBER 2003 – REVISED MAY 2016
11 Device and Documentation Support
11.1 Related Documentation
•
TI Precision Design, 16 bit 1MSPS Data Acquisition Reference Design for Single-Ended Multiplexed
Applications, TIPD173.
11.2 Related Links
Table 4 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
INA139-Q1
Click here
Click here
Click here
Click here
Click here
INA169-Q1
Click here
Click here
Click here
Click here
Click here
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2003–2016, Texas Instruments Incorporated
Product Folder Links: INA139-Q1 INA169-Q1
Submit Documentation Feedback
19
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
INA139QPWRQ1
ACTIVE
TSSOP
PW
8
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
INA139
INA169QPWRQ1
ACTIVE
TSSOP
PW
8
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
INA169
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
