User's Guide
SBAU220 – February 2014
INA300EVM User's Guide
This user’s guide describes the INA300 evaluation module (EVM). This document discusses the set-up
and operating instructions, schematic, printed circuit board (PCB) design, and bill of materials. Throughout
this document, the abbreviation EVM and the term evaluation module are synonymous with the
INA300EVM.
Contents
1
Overview
.....................................................................................................................
2
List of Figures
1
INA300EVM Overview......................................................................................................
3
2
Connecting the INA300EVM with Voltage Sources ....................................................................
4
3
Connecting the INA300EVM as a High-Side Current Comparator ...................................................
5
4
Enable/Disable Jumper Location..........................................................................................
7
5
Enable/Disable Schematic Connections .................................................................................
7
6
Transparent/Latch Jumper .................................................................................................
8
7
Transparent/Latch Schematic Connections
.............................................................................
Delay Jumper Location .....................................................................................................
Delay Schematic Connections ............................................................................................
Hysteresis Jumper Location..............................................................................................
Hysteresis Schematic Connections .....................................................................................
Limit Jumper Location ....................................................................................................
Limit Schematic Connections ............................................................................................
Low-Pass, Passive Input Filter ..........................................................................................
INA300EVM Schematic ...................................................................................................
INA300EVM Top Overlay.................................................................................................
INA300EVM Top Solder Mask ...........................................................................................
INA300EVM Top Layer ...................................................................................................
INA300EVM Bottom Layer ...............................................................................................
INA300EVM Bottom Solder Mask .......................................................................................
INA300EVM Drill Drawing ................................................................................................
INA300EVM Board Dimensions .........................................................................................
8
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
9
9
10
10
11
11
12
13
14
14
14
14
15
15
15
All trademarks are the property of their respective owners.
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
1
Overview
1
www.ti.com
Overview
The INA300 is a high common-mode, precision, bidirectional, current-sensing comparator that can be
configured to detect overcurrent conditions through the voltage developed across a shunt resistor.
Operating from a single power supply from 2.7 V to 5.5 V, the INA300 can be configured to detect shunt
voltages from 0 V to 250 mV in the presence of common-mode voltages from 0 V to 36 V. The
INA300EVM allows for easy user configuration of the INA300 device by using jumpers. The following
features can be programmed in this manner:
• Enable and disable,
• Latch mode and transparent mode,
• Delay (10 µs, 50 µs, and 100 µs),
• Hysteresis (2 mV, 5 mV, and 10 mV), and
• Threshold set by a single resistor or an external voltage source.
The comparator threshold comes factory programmed at 200 mV and can be easily customized anywhere
within its operating range by replacing a single, pin-socketed resistor. On-board connectors allow for user
control of all inputs and outputs with a microprocessor, pattern generator, or digital-to-analog converter
(DAC). Test points are available for all signals, thus making design verification fast and easy.
For a more detailed description of the INA300, refer to the product data sheet (SBOS613) available from
the Texas Instruments web site at www.ti.com. Support documents are listed in the Related
Documentation from Texas Instruments section.
1.1
Information About Cautions and Warnings
This document contains caution and warning statements.
CAUTION
Applying more than 40 V to the IN+ or IN– pins may result in damage to the
INA300EVM.
Applying more than 6 V to VDD may result in damage to the INA300EVM.
Applying more than VDD + 0.3 V or less than GND – 0.3 V to any other
terminal connection may result in damage to the INA300EVM.
WARNING
This equipment is intended for use in a laboratory test environment
only. To prevent personal injury, the use of safety glasses is
recommended.
Use of this equipment must be performed by qualified personnel
trained in electronics theory and understand the risks and hazards
of the assembly to be tested.
A caution statement describes a situation that could potentially damage your software or equipment. A
warning statement describes a situation that could potentially cause injury. The information in a caution or
a warning is provided for your protection. Please read each caution and warning carefully.
2
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
1.2
Related Documentation from Texas Instruments
The following document provides information regarding Texas Instruments integrated circuits used in the
assembly of the INA300EVM. This document is available from the TI web site under literature number
SBOS613. Any letter appended to the literature number corresponds to the document revision that is
current at the time of the writing of this document. Newer revisions may be available from the TI web site
at http://www.ti.com, or call the Texas Instruments Literature Response Center at (800) 477-8924 or the
Product Information Center at (972) 644-5580. When ordering, identify the document by both title and
literature number.
1.3
Document
Literature Number
INA300 Product Data Sheet
SBOS613
If You Need Assistance
If you have questions about the INA300 evaluation module, post a question in the amplifiers forum at
http://e2e.ti.com Include INA300EVM in the subject heading.
Hardware Description
The INA300EVM consists of a double-sided printed circuit board (PCB) populated with an INA300 device,
connectors for power, ground, signal input and output terminals, test points, jumpers, a light-emitting diode
(LED) to monitor the Alert pin status, and power-supply bypass capacitors. A footprint for a passive input
filter is also provided. Figure 1 shows an overview of the INA300EVM.
Test Pad
Jumper
Connector
INA300
Limit Setting Resistor
Figure 1. INA300EVM Overview
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
3
Overview
www.ti.com
Configuring and Using the INA300EVM
The INA300EVM is fully assembled, factory tested, and ready to use. For fast evaluation of the INA300
device, the INA300EVM can be configured as shown in Figure 2.
VS = +2.7 V to 5.5 V
VCM = 0.3 V to 36 V
VSHUNT
Figure 2. Connecting the INA300EVM with Voltage Sources
Power-Supply Connections
Connect a power supply (see Figure 2) to connector T2 to supply power to the INA300EVM. This power
supply must be within the range of +2.7 V to +5.5 V and must be connected to the VDD terminal of
connector T2. Connect the GND terminal of connector T2 to ground.
Differential Input Voltage Connections Using a Shunt Resistor
These connections are established by using a voltage source to create the shunt voltage at the input.
Connect a voltage source between the IN+ and IN– inputs at connector T1 as shown in Figure 2. This
shunt voltage source provides the differential input to the INA300. The INA300 compares the value of this
differential input to the value set by the limit resistor or external voltage source. The INA300 alerts if the
limit setting is exceeded. The alert is monitored by a red LED on the INA300EVM.
Common-Mode Input Voltage Connections
Connect a voltage source between the +IN connection at connector T1 and ground as shown in Figure 2.
This common-mode voltage source must be within the range of –0.3 V to +36 V.
4
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
Differential Input Voltage Connections
These connections are established by using a shunt resistor to create the shunt voltage at the input.
Configuring the differential input to the INA300EVM as a shunt resistor in series with a load may be more
suitable in some evaluations than configuring the differential input to the INA300EVM as a voltage source;
see Figure 2. Figure 3 shows the connections for a high-side current comparator using the INA300EVM.
VS = +2.7 V to 5.5 V
VCM = 0.3 V to 36 V
RSHUNT
Load
Figure 3. Connecting the INA300EVM as a High-Side Current Comparator
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
5
Overview
www.ti.com
Setting the Input Threshold Voltage
The INA300 is a voltage comparator. The comparator threshold voltage is set by the value of the voltage
applied to the Limit pin on the INA300. On the INA300EVM, a resistor is connected to the output of the
Limit pin and ground. The output of the Limit pin is a constant current sourced from an internal, precision,
band-gap voltage reference. The typical value of this current source is 20 µA. The INA300EVM comes
configured from the factory with a 10-kΩ resistor connected to the Limit pin. The voltage developed across
this resistor is given by Equation 1.
VLIMIT = 20 µA × RLIMIT
where:
•
•
RLIMIT = 10 kΩ and
VLIMIT = 200 mV.
(1)
Configuring the INA300EVM Jumpers
The INA300EVM includes five jumpers to quickly configure the INA300. These jumpers are the
enable/disable jumper, transparent/latch jumper, delay jumper, hysteresis jumper, and limit jumper.
Table 1 describes the jumper operation on the INA300EVM.
Table 1. Jumper Functionality
Jumper Name
6
Function When Connected To:
VDD
(1)
FLOAT
Limit Resistor
External VLIMIT
ENABLE
Disabled
Enabled
—
—
J2
LATCH
Latch
Transparent (1)
Transparent
—
—
J3
DELAY
100 µs (1)
50 µs
10 µs
—
—
J4
HYS
10 mV
5 mV (1)
2 mV
—
—
—
Threshold
voltage
determined by
RLIMIT × 20 µA (1)
Threshold
voltage input
from external
DAC or voltage
source
LIMIT
Enabled
GND
J1
J5
(1)
Middle Pin
Connection
—
—
EVM default configuration.
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
Enable/Disable Jumper
The INA300EVM uses a jumper-configurable connection that enables or disables the INA300. Figure 4
shows the location of the enable/disable jumper (J1). The INA300EVM PCB is clearly marked for easy
configuration. Connecting the jumper to ground disables the INA300; connecting the jumper to VDD
enables the INA300. The INA300EVM comes enabled from the factory by default. If the jumper is left
floating or removed, the INA300 defaults to the enabled state. Refer to Figure 5 for detailed operation of
the enable/disable jumper.
Enabled
Disabled
Figure 4. Enable/Disable Jumper Location
GND
VDD
J1
INA300 Enable Pin
Figure 5. Enable/Disable Schematic Connections
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
7
Overview
www.ti.com
Transparent/Latch Jumper
The INA300EVM uses a jumper-configurable connection that enables either transparent or latched mode
operation in the INA300. Figure 6 shows the location of the transparent/latch jumper (J2). The
INA300EVM PCB is clearly marked for easy configuration. Connecting the jumper to ground configures
the INA300 in transparent mode; connecting the jumper to VDD configures the INA300 in latch mode. The
INA300EVM comes configured in transparent mode from the factory by default. If the jumper is left floating
or removed, the INA300 defaults to the transparent state. Refer to Figure 7 for detailed operation of the
transparent/latch jumper.
Latch
Transparent
Figure 6. Transparent/Latch Jumper
GND
VDD
J2
INA300 Latch Pin
Figure 7. Transparent/Latch Schematic Connections
8
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
Delay Jumper
The INA300EVM uses a jumper-configurable connection that allows for programming a delay into the
INA300 response. Figure 8 shows the location of the delay jumper (J3). The INA300EVM PCB is clearly
marked for easy configuration. Connecting the jumper to ground configures the INA300 for a 50-µs delay;
connecting the jumper to VDD configures the INA300 for a 100-µs delay. If the jumper is left floating or
removed, the INA300 defaults to a 10-µs delay. The INA300EVM comes configured for a 100-µs delay
from the factory by default. Refer to Figure 9 for detailed operation of the delay jumper.
100-µs Delay
10-µs Delay if
Jumper is Removed
50-µs Delay
Figure 8. Delay Jumper Location
GND
VDD
J3
INA300 Delay Pin
Figure 9. Delay Schematic Connections
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
9
Overview
www.ti.com
Hysteresis Jumper
The INA300EVM uses a jumper-configurable connection that allows for programming hysteresis into the
INA300 response. Figure 10 shows the location of the hysteresis jumper (J4). The INA300EVM PCB is
clearly marked for easy configuration. Connecting the jumper to ground configures the INA300 for a 5-mV
hysteresis; connecting the jumper to VDD configures the INA300 for a 10-mV hysteresis. If the jumper is
left floating or removed, the INA300 defaults to a 2-mV hysteresis. The INA300EVM comes configured for
a 5-mV hysteresis from the factory by default. Refer to Figure 11 for detailed operation of the hysteresis
jumper.
5-mV Hysteresis
2-mV Hysteresis if
Jumper is Removed
10-mV Hysteresis
Figure 10. Hysteresis Jumper Location
VDD
GND
J4
INA300 Hysteresis Pin
Figure 11. Hysteresis Schematic Connections
10
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
Limit Jumper
The INA300EVM uses a jumper-configurable connection that uses either a resistor or an external voltage
source, such as a DAC (not included on the INA300EVM), as the input to the limit pin. Figure 12 shows
the location of the limit jumper (J5). The INA300EVM PCB is clearly marked for easy configuration. The
middle pin of the limit jumper is connected directly to the INA300 limit pin. The jumper connects the limit
pin to either RLIMIT on the INA300EVM PCB or to connector T3, which can be connected to an external
voltage source. If the limit jumper is left floating or removed, the INA300 limit pin saturates to an internal
power rail of approximately 1.3 V, which is outside the 0-V to 250-mV normal operating range of the limit
pin. Leaving the limit pin floating during operation does not damage the INA300, but is not recommended.
The INA300EVM comes configured from the factory for use with the RLIMIT resistor by default. Refer to
Figure 13 for detailed operation of the limit jumper.
Figure 12. Limit Jumper Location
This terminal cannot be left floating, it must be connected to
either the limit resistor or the EXT VLIMIT for proper functionality.
EXT VLIMIT Terminal on
Connector T3
Limit Resistor
J5
INA300 Limit
Terminal
Figure 13. Limit Schematic Connections
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
11
Overview
www.ti.com
Optional Input Filter
The INA300EVM is designed to accommodate a user-configurable, first-order, low-pass, passive input
filter. Figure 14 shows the location and construction of the filter. The INA300EVM comes populated with
two 0-Ω resistors (R4 and R5). However, the filter capacitor is not installed.
R4
IN+
0:
IN+
C3
0:
INA300
IN
IN
R5
Figure 14. Low-Pass, Passive Input Filter
To implement an input filter, replace the two 0-Ω resistors (R4 and R5) with equal value resistors of up to
10 Ω. Select capacitor C3 according to Equation 2.
1
C3 =
2 ´ p ´ (R4 + R5) ´ f3dB
where:
•
12
f3dB is the desired cutoff frequency
INA300EVM User's Guide
(2)
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
INA300EVM Schematic, PCB, and BOM
This section includes the INA300EVM schematic, printed circuit board, and bill of materials.
INA300EVM Schematic Diagram
Figure 15 shows a schematic of the INA300EVM.
trans
J1
disabled
T2
LATCH
latch
ENABLE
VDD
enabled
GND
J2
C1
1µF
C2
0.1µF
R3
470O
T1
R4
0O
9
4
C3
DNP
D1
6
1
IN+
IN-
T3
R1
10kO
INA300
R5
0O
5
3
2
8
7
10
DELAY
J5
10mV
2mV
J4
5mV
100µS
10µS
J3
50µS
R2
5kO
ENABLE
LATCH
HYS
ALERT
VLIMIT
DELAY
HYS
Figure 15. INA300EVM Schematic
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
13
Overview
www.ti.com
INA300EVM Printed Circuit Board (PCB)
Figure 16 to Figure 22 show different views of the INA300EVM PCB.
Figure 16. INA300EVM Top Overlay
Figure 17. INA300EVM Top Solder Mask
14
Figure 18. INA300EVM Top Layer
Figure 19. INA300EVM Bottom Layer
INA300EVM User's Guide
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Overview
www.ti.com
Figure 20. INA300EVM Bottom Solder Mask
Figure 21. INA300EVM Drill Drawing
Figure 22. INA300EVM Board Dimensions
SBAU220 – February 2014
Submit Documentation Feedback
INA300EVM User's Guide
Copyright © 2014, Texas Instruments Incorporated
15
Overview
www.ti.com
INA300EVM Bill of Materials (BOM)
The INA300EVM bill of materials is listed in Table 2.
Table 2. Bill of Materials
Qty
13
SMT
1
1 µF
Ref Des
Description
ALERT, DELAY, ENABLE,
GND, HYS, IN+, IN–,
Test point, compact, SMT
LATCH, LIMIT, VDD, VLIMIT
C1
C2, C3
Package Reference
Vendor
Part Number
5016
Testpoint, Keystone, Compact
Keystone
Capacitor, ceramic, 1 µF, 25 V, ±10%, X5R, 0805
0805
AVX
Capacitor, ceramic, 0.1 µF, 25 V, ±10%, X5R,
0603
0603
AVX
08053D105KAT2A
06033D104KAT2A
2
0.1 µF
1
Red
D1
LED, red, SMD
LED_0805
Lite-On
LTST-C170KRKT
4
—
H1-H4
Bumpon, hemisphere, 0.44 × 0.20, black
Black bumpon
3M
SJ-5003 (BLACK)
1
—
INA300
High or low side, bidirectional, zero-drift series,
current sense comparator, DSQ0010A
QFN-10, 2 mm × 2 mm
Texas Instruments
5
—
J1-J5
Header, TH, 100 mil, 3 × 1, gold plated, 230 mil
above insulator
TSW-103-07-G-S
Samtec, Inc
5
—
J1-J5
Strip, female socket, 1 × 2, open top, 0.100
Strip
TE Connectivity
—
LBL1
Thermal transfer printable labels, 0.650" W ×
0.200" H, 10000 per roll
PCB label, 0.650" H × 0.200"
W
Brady
1
—
R1
Resistor, 10 kΩ, 5%, 0.1 W, [0603]
0603
Stackpole
RMCF0603JT10K0
1
10 kΩ
R2
Resistor, 10 kΩ, 0.1%, 0.25 W, axial
Axial
Yageo
MFP-25BRD52-10K
1
10 kΩ
R3
Resistor, 470 Ω, 5%, 0.1 W, [0603]
0603
Vishay-Dale
1
16
Value
INA300AIDSQ
TSW-103-07-G-S
2-382811-1
THT-14-423-10
CRCW0603470RJNEA
2
470 Ω
R4, R5
Resistor, 0 Ω, x%, x W, [PackageReference]
0603
Panasonic Electronic
Components
2
0Ω
T1, T2
Terminal block, 6 A, 3.5 mm pitch, 2-pos, TH
7.0 × 8.2 × 6.5 mm
On-Shore Technology, Inc
ED555/2DS
1
—
T3
Terminal block, 6 A, 3.5 mm pitch, 6-pos, TH
20.5 × 8.2 × 6.5 mm
On-Shore Technology, Inc
ED555/6DS
INA300EVM User's Guide
ERJ-3GEY0R00V
SBAU220 – February 2014
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of EVMs for RF Products in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,
CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine
and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable
safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to
perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
