Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
ISO7840x High-Performance, 8000-VPK Reinforced Quad-Channel Digital Isolator
1 Features
3 Description
•
•
•
•
•
The ISO7840x device is a high-performance, quadchannel digital isolator with a 8000-VPK isolation
voltage. This device has reinforced isolation
certifications according to VDE, CSA, CQC, and TUV.
The isolator provides high electromagnetic immunity
and low emissions at low-power consumption, while
isolating CMOS or LVCMOS digital I/Os. Each
isolation channel has a logic input and output buffer
separated by a silicon-dioxide (SiO2) insulation
barrier.
1
•
•
•
•
•
•
•
•
Signaling Rate: Up to 100 Mbps
Wide Supply Range: 2.25 V to 5.5 V
2.25-V to 5.5-V Level Translation
Wide Temperature Range: –55°C to +125°C
Low-Power Consumption, Typical 1.7 mA per
Channel at 1 Mbps
Low Propagation Delay: 11 ns Typical
(5-V Supplies)
Industry leading CMTI (Min): ±100 kV/μs
Robust Electromagnetic Compatibility (EMC)
System-Level ESD, EFT, and Surge Immunity
Low Emissions
Isolation Barrier Life: >40 Years
Wide Body SOIC-16 Package and Extra-Wide
Body SOIC-16 Package Options
Safety and Regulatory Approvals:
– 8000-VPK Reinforced Isolation per DIN V VDE
V 0884-10 (VDE V 0884-10):2006-12
– 5.7-kVRMS Isolation for 1 Minute per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 60601-1 End Equipment
Standards
– CQC Certification per GB4943.1-2011
– TUV Certification per EN 61010-1 and EN
60950-1
– All DW Package Certifications Complete;
DWW Package Certifications Complete per
UL, VDE, TUV and Planned for CSA and CQC
2 Applications
•
•
•
•
•
•
Industrial Automation
Motor Control
Power Supplies
Solar Inverters
Medical Equipment
Hybrid Electric Vehicles
This device comes with enable pins that can be used
to put the respective outputs in high impedance for
multi-master driving applications and to reduce power
consumption. The ISO7840 device has four forward
and zero reverse-direction channels. If the input
power or signal is lost, the default output is high for
the ISO7840 device and low for the ISO7840F
device. See the Device Functional Modes section for
further details.
Used in conjunction with isolated power supplies, this
device helps prevent noise currents on a data bus or
other circuits from entering the local ground and
interfering with or damaging sensitive circuitry.
Through innovative chip design and layout
techniques, electromagnetic compatibility of the
ISO7840 device has been significantly enhanced to
ease system-level ESD, EFT, surge, and emissions
compliance.
The ISO7840 device is available in 16-pin SOIC
wide-body (DW) and extra-wide body (DWW)
packages.
Device Information(1)
PART NUMBER
ISO7840
ISO7840F
PACKAGE
BODY SIZE (NOM)
DW (16)
10.30 mm × 7.50 mm
DWW (16)
10.30 mm × 14.0 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
VCCI
Isolation
Capacitor
VCCO
INx
OUTx
ENx
GNDI
GNDO
VCCI and GNDI are supply and ground
connections respectively for the input
channels.
VCCO and GNDO are supply and ground
connections respectively for the output
channels.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
1
1
1
2
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings.............................................................. 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 6
Power Ratings........................................................... 6
Insulation Specifications............................................ 7
Safety-Related Certifications..................................... 8
Safety Limiting Values .............................................. 8
Electrical Characteristics—5-V Supply ..................... 9
Supply Characteristics—5-V Supply ....................... 9
Electrical Characteristics—3.3-V Supply .............. 10
Supply Current Characteristics—3.3-V Supply ..... 10
Electrical Characteristics—2.5-V Supply .............. 11
Supply Current Characteristics—2.5-V Supply ..... 11
Switching Characteristics—5-V Supply................. 12
Switching Characteristics—3.3-V Supply.............. 12
Switching Characteristics—2.5-V Supply.............. 13
Insulation Characteristics Curves ......................... 14
6.19 Typical Characteristics .......................................... 15
7
8
Parameter Measurement Information ................ 16
Detailed Description ............................................ 18
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
18
18
19
20
Application and Implementation ........................ 21
9.1 Application Information............................................ 21
9.2 Typical Application .................................................. 21
10 Power Supply Recommendations ..................... 23
11 Layout................................................................... 24
11.1 Layout Guidelines ................................................. 24
11.2 Layout Example .................................................... 24
12 Device and Documentation Support ................. 25
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
25
13 Mechanical, Packaging, and Orderable
Information ........................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (March 2016) to Revision B
Page
•
Added Features 2.25 V to 5.5 V Level Translation ................................................................................................................ 1
•
Changed the number of years for the isolation barrier life in the Features section .............................................................. 1
•
VDE certification is now complete ......................................................................................................................................... 1
•
Changed the input-to-output test voltage parameter to apparent charge in the Insulation Specifications ............................ 7
•
Changed VCCO to VCCI for the minimum value of the input threshold voltage hysteresis parameter in all electrical
characteristics tables .............................................................................................................................................................. 9
•
Added VCM to the test condition of the common-mode transient immunity parameter in all electrical characteristics tables 9
•
Added the lifetime projection graphs for DW and DWW packages to the Safety Limiting Values section ......................... 14
Changes from Original (July 2015) to Revision A
Page
•
Changed Features From: Industry leading CMTI To: Industry leading CMTI (MIN) ............................................................. 1
•
Changed the Safety and Regulatory Approvals list of Features ............................................................................................ 1
•
Added Features "TUV Certification per EN 61010-1 and EN 60950-1" ................................................................................. 1
•
Changed text in the first paragraph of the Description From: "certifications according to VDE, CSA, and CQC". To:
"certifications according to VDE, CSA, CQC, and TUV." ...................................................................................................... 1
•
Added the DWW pinout image ............................................................................................................................................... 4
•
Added the DWW package to the Thermal Information .......................................................................................................... 6
•
Changed Package Insulation and Safety-Related Specifications, added the 16-DWW Package information....................... 7
•
Added the DWW package information, added "Climatic category", and deleted Note 1 in Insulation Characteristics ......... 7
•
Added Note 1 to Insulation Characteristics ........................................................................................................................... 7
2
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
•
Changed IEC 60664-1 Ratings Table ................................................................................................................................... 7
•
Added the TUV and DWW package information to the Regulatory Information section and Regulatory Information.
Deleted Note 1 in Regulatory Information .............................................................................................................................. 8
•
Changed the Supply Current section of Supply Characteristics—5-V Supply ....................................................................... 9
•
Changed the Supply Current section of Supply Current Characteristics—3.3-V Supply ..................................................... 10
•
Changed the Supply Current section ofSupply Current Characteristics—2.5-V Supply ..................................................... 11
•
Changed Device I/O Schematics ......................................................................................................................................... 20
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
3
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
5 Pin Configuration and Functions
DW and DWW Packages
16-Pin SOIC
Top View
1
16 VCC2
GND1 2
15 GND2
VCC1
3
14 OUTA
INB
4
INC
5
IND
6
11 OUTD
NC
7
10
ISOLATION
INA
GND1 8
13 OUTB
12 OUTC
EN2
9 GND2
Pin Functions
PIN
NAME
EN2
GND1
GND2
NO.
10
2
8
9
15
I/O
I
DESCRIPTION
Output enable 2. Output pins on side 2 are enabled when EN2 is high or open and in highimpedance state when EN2 is low.
—
Ground connection for VCC1
—
Ground connection for VCC2
INA
3
I
Input, channel A
INB
4
I
Input, channel B
INC
5
I
Input, channel C
IND
6
I
Input, channel D
NC
7
—
Not connected
OUTA
14
O
Output, channel A
OUTB
13
O
Output, channel B
OUTC
12
O
Output, channel C
OUTD
11
O
Output, channel D
VCC1
1
—
Power supply, VCC1
VCC2
16
—
Power supply, VCC2
4
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
6 Specifications
6.1 Absolute Maximum Ratings
See
(1)
VCC1,
VCC2
Supply voltage (2)
Voltage
MAX
–0.5
6
–0.5
VCCX + 0.5
–0.5
VCCX + 0.5 (3)
–0.5
(3)
VCCX + 0.5
–15
Surge immunity
(1)
(2)
(3)
V
(3)
OUTx
Output current
Tstg
UNIT
INx
EN2
IO
MIN
Storage temperature
–65
V
15
mA
12.8
kV
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to the local ground terminal (GND1 or GND2) and are peak
voltage values.
Maximum voltage must not exceed 6 V
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
±6000
Charged device model (CDM), per JEDEC specification JESD22-C101, all
pins (2)
±1500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
VCC1,
VCC2
Supply voltage
2.25
VCCO
IOH
High-level output current
Low-level output current
(1)
=5V
(1)
MAX
5.5
= 2.5 V
mA
–1
4
VCCO (1) = 3.3 V
2
VCCO
V
–2
VCCO (1) = 5 V
(1)
UNIT
–4
VCCO (1) = 3.3 V
VCCO
IOL
NOM
= 2.5 V
mA
1
VCCI
(1)
High-level input voltage
VIL
Low-level input voltage
0
0.3 × VCCI (1)
DR
Signaling rate
0
100
Mbps
TJ
Junction temperature (2)
–55
150
°C
TA
Ambient temperature
–55
125
°C
(1)
(2)
0.7 × VCCI
(1)
VIH
25
V
V
VCCI = Input-side VCC; VCCO = Output-side VCC.
To maintain the recommended operating conditions for TJ, see Thermal Information.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
5
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
6.4 Thermal Information
ISO7840
THERMAL METRIC (1)
DW (SOIC)
DWW (SOIC)
16 Pins
16 Pins
UNIT
RθJA
Junction-to-ambient thermal resistance
78.9
78.9
°C/W
RθJC(top)
Junction-to-case(top) thermal resistance
41.6
41.1
°C/W
RθJB
Junction-to-board thermal resistance
43.6
49.5
°C/W
ψJT
Junction-to-top characterization parameter
15.5
15.2
°C/W
ψJB
Junction-to-board characterization parameter
43.1
48.8
°C/W
N/A
N/A
°C/W
RθJC(bottom) Junction-to-case(bottom) thermal resistance
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Power Ratings
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF, input a 50 MHz 50% duty cycle square wave
MAX
UNIT
PD
Maximum power dissipation by ISO7840x
PARAMETER
200
mW
PD1
Maximum power dissipation by side-1 of
ISO7840x
40
mW
PD2
Maximum power dissipation by side-2 of
ISO7840x
160
mW
6
Submit Documentation Feedback
TEST CONDITIONS
MIN
TYP
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
6.6 Insulation Specifications
PARAMETER
TEST CONDITIONS
External clearance (1)
CPG
SPECIFICATION
UNIT
DW
DWW
Shortest pin-to-pin distance through air
>8
>14.5
mm
External creepage (1)
Shortest pin-to-pin distance across the package
surfaceHigh Voltage Feature Description
>8
>14.5
mm
DTI
Distance through the insulation
Minimum internal gap (internal clearance)
>21
>21
μm
CTI
Comparative tracking index
DIN EN 60112 (VDE 0303-11); IEC 60112; UL 746A
>600
>600
V
I
I
Rated mains voltage ≤ 600 VRMS
I–IV
I–IV
Rated mains voltage ≤ 1000 VRMS
I–III
I–IV
2121
2828
VPK
1500
2000
VRMS
GENERAL
CLR
Material group
Overvoltage category per IEC
60664-1
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 (2)
VIORM
Maximum repetitive peak isolation
voltage
VIOWM
AC voltage (sine wave); Time dependent dielectric
Maximum isolation working voltage breakdown (TDDB) Test, see Figure 1 and Figure 2
DC voltage
2121
2828
VDC
8000
8000
VPK
8000
8000
VPK
Method a: After I/O safety test subgroup 2/3,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.2 × VIORM = 2545 VPK (DW) and 3394 VPK
(DWW), tm = 10 s
≤5
≤5
Method a: After environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.6 × VIORM = 3394 VPK (DW) and 4525 VPK
(DWW), tm = 10 s
≤5
≤5
Method b1: At routine test (100% production) and
preconditioning (type test)
Vini = VIOTM, tini = 1 s;
Vpd(m) = 1.875 × VIORM = 3977 VPK (DW) and 5303 VPK
(DWW), tm = 1 s
≤5
≤5
VIO = 0.4 × sin (2πft), f = 1 MHz
2
2
VIOTM
Maximum transient isolation
voltage
VTEST = VIOTM
t = 60 s (qualification)
t= 1 s (100% production)
VIOSM
Maximum surge isolation voltage (3)
Test method per IEC 60065, 1.2/50 µs waveform,
VTEST = 1.6 × VIOSM = 12800 VPK (qualification)
qpd
Apparent charge
(4)
CIO
Barrier capacitance, input to
output (5)
RIO
Isolation resistance, input to
output (5)
>1012
>1012
11
>1011
9
>10
>109
Pollution degree
2
2
Climatic category
55/125/21
55/125/21
5700
5700
VIO = 500 V, TA = 25°C
VIO = 500 V, 100°C ≤ TA ≤ 125°C
VIO = 500 V at TS = 150°C
>10
pC
pF
Ω
UL 1577
VISO
(1)
(2)
(3)
(4)
(5)
Withstand isolation voltage
VTEST = VISO = 5700 VRMS, t = 60 s (qualification),
VTEST = 1.2 × VISO = 6840 VRMS, t = 1 s (100%
production)
VRMS
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care
should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on
the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves, ribs, or both on a printed circuit board are used to help increase these specifications.
This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by
means of suitable protective circuits.
Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-pin device.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
7
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
6.7 Safety-Related Certifications
Certifications for the DW package are complete. DWW package certifications are complete for UL, VDE and TUV and
planned for CSA and CQC.
VDE
Certified according to DIN
V VDE V 0884-10 (VDE V
0884-10):2006-12 and DIN
EN 60950-1 (VDE 0805
Teil 1):2011-01
CSA
UL
Approved under CSA
Component Acceptance
Notice 5A, IEC 60950-1 and
IEC 60601-1
CQC
TUV
Certified according to GB
4943.1-2011
Certified according to
EN 61010-1:2010 (3rd Ed) and
EN 60950-1:2006/A11:2009/A1:2010/
A12:2011/A2:2013
Reinforced insulation per CSA
60950-1-07+A1+A2 and IEC
60950-1 2nd Ed., 800 VRMS
Reinforced insulation
(DW package) and 1450 VRMS
Maximum transient
isolation voltage, 8000 VPK; (DWW package) max working
voltage (pollution degree 2,
Maximum repetitive peak
Single protection, 5700
isolation voltage, 2121 VPK material group I);
VRMS
(DW), 2828 VPK (DWW);
2 MOPP (Means of Patient
Maximum surge isolation
Protection) per CSA 60601voltage, 8000 VPK
1:14 and IEC 60601-1 Ed. 3.1,
250 VRMS (354 VPK) max
working voltage (DW package)
Reinforced Insulation,
Altitude ≤ 5000 m, Tropical
Climate, 250 VRMS
maximum working voltage
5700 VRMS Reinforced insulation per
EN 61010-1:2010 (3rd Ed) up to
working voltage of 600 VRMS (DW
package) and 1000 VRMS (DWW
package)
5700 VRMS Reinforced insulation per
EN 60950-1:2006/A11:2009/A1:2010/
A12:2011/A2:2013 up to working
voltage of 800 VRMS (DW package) and
1450 VRMS (DWW package)
Certificate number:
40040142
Certificate number:
CQC15001121716
Client ID number: 77311
Master contract number:
220991
Certified according to UL
1577 Component
Recognition Program
File number: E181974
6.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A failure of
the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to overheat
the die and damage the isolation barrier potentially leading to secondary system failures.
PARAMETER
IS
Safety input, output, or supply
current
PS
Safety input, output, or total
power
TS
Maximum safety temperature
TEST CONDITIONS
MIN
TYP
MAX
RθJA = 78.9°C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C
288
RθJA = 78.9°C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C
440
RθJA = 78.9°C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C
576
RθJA = 78.9°C/W, TJ = 150°C, TA = 25°C
UNIT
mA
1584
mW
150
°C
The maximum safety temperature is the maximum junction temperature specified for the device. The power
dissipation and junction-to-air thermal impedance of the device installed in the application hardware determines
the junction temperature. The assumed junction-to-air thermal resistance in the Thermal Information is that of a
device installed on a high-K test board for leaded surface-mount packages. The power is the recommended
maximum input voltage times the current. The junction temperature is then the ambient temperature plus the
power times the junction-to-air thermal resistance.
8
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
6.9 Electrical Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO – 0.4
VCCO – 0.2
MAX
UNIT
VOH
High-level output voltage
IOH = –4 mA; see Figure 11
VOL
Low-level output voltage
IOL = 4 mA; see Figure 11
V
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI at INx or EN2
IIL
Low-level input current
VIL = 0 V at INx or EN2
–10
μA
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1500 V; see
Figure 14
100
kV/μs
CI
Input capacitance
VI = VCC/2 + 0.4 × sin (2πft), f = 1 MHz, VCC =
5V
0.2
0.4
0.1 × VCCI
V
V
10
2
μA
pF
6.10 Supply Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
MAX
ICC1
1.3
2
ICC2
0.4
0.6
EN2 = 0 V, VI = VCCI (ISO7840F), VI = 0
V (ISO7840) EN2 = 0 V
ICC1
6
8.5
ICC2
0.4
0.6
VI = 0 V (ISO7840F), VI = VCCI
(ISO7840)
ICC1
1.3
2
ICC2
2.2
3.1
VI = VCCI (ISO7840F), VI = 0 V
(ISO7840)
ICC1
5.9
8.6
ICC2
2.5
3.3
ICC1
3.6
5.3
ICC2
2.6
3.7
ICC1
3.8
5.4
ICC2
4.5
5.9
DC signal
Supply current
1 Mbps
10 Mbps
DW package
100 Mbps
DWW package
(1)
TYP
EN2 = 0 V, VI = 0 V (ISO7840F), VI =
VCCI (1) (ISO7840)
Disable
All channels switching with
square wave clock input;
CL = 15 pF
MIN
ICC1
5.1
5.9
ICC2
23.8
27.4
ICC1
5.1
5.9
ICC2
23.8
28.5
UNIT
mA
mA
mA
mA
mA
mA
mA
mA
VCCI = Input-side VCC; VCCO = Output-side VCC.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
9
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
6.11 Electrical Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO – 0.4
VCCO – 0.2
MAX
UNIT
VOH
High-level output voltage
IOH = –2 mA; see Figure 11
VOL
Low-level output voltage
IOL = 2 mA; see Figure 11
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI at INx or EN2
IIL
Low-level input current
VIL = 0 V at INx or EN2
–10
μA
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1500 V; see Figure 14
100
kV/μs
0.2
V
0.4
0.1 × VCCI
V
V
10
μA
6.12 Supply Current Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
Disable
DC signal
Supply current
SUPPLY
CURRENT
10
MAX
ICC1
1.3
2
ICC2
0.4
0.6
EN2 = 0 V, VI = VCCI (1) (ISO7840F), VI
= 0 V (ISO7840)
ICC1
6
8.5
ICC2
0.4
0.6
VI = 0 V (ISO7840F), VI = VCCI (1)
(ISO7840)
ICC1
1.3
2
ICC2
2.2
3
VI = VCCI (1) (ISO7840F), VI = 0 V
(ISO7840)
ICC1
5.9
8.6
ICC2
2.4
3.3
ICC1
3.6
5.3
ICC2
2.5
3.6
ICC1
3.7
5.3
ICC2
3.9
5.1
ICC1
4.5
5.8
ICC2
17.7
20.6
10 Mbps
100 Mbps
(1)
TYP
EN2 = 0 V, VI = 0 V (ISO7840F), VI =
VCCI (1) (ISO7840)
1 Mbps
All channels switching with
square wave clock input;
CL = 15 pF
MIN
UNIT
mA
mA
mA
mA
mA
mA
mA
VCCI = Input-side VCC; VCCO = Output-side VCC.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
6.13 Electrical Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO – 0.4
VCCO – 0.2
MAX
UNIT
VOH
High-level output voltage
IOH = –1 mA; see Figure 11
VOL
Low-level output voltage
IOL = 1 mA; see Figure 11
VI(HYS)
Input threshold voltage
hysteresis
IIH
High-level input current
VIH = VCCI at INx or EN2
IIL
Low-level input current
VIL = 0 V at INx or EN2
–10
μA
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1500 V; see Figure 14
100
kV/μs
0.2
V
0.4
V
0.1 × VCCI
V
10
μA
6.14 Supply Current Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
Disable
DC signal
Supply current
SUPPLY
CURRENT
MAX
ICC1
1.3
2
ICC2
0.4
0.6
EN2 = 0 V, VI = VCCI (1) (Devices with
suffix F), VI = 0 V (Devices without suffix
F)
ICC1
6
8.5
ICC2
0.4
0.6
VI = 0 V (Devices with suffix F), VI =
VCCI (1) (Devices without suffix F)
ICC1
1.3
2
ICC2
2.2
3
VI = VCCI (1) (Devices with suffix F), VI =
0 V (Devices without suffix F)
ICC1
5.9
8.6
ICC2
2.4
3.3
ICC1
3.6
5.3
ICC2
2.5
3.5
ICC1
3.7
5.3
ICC2
3.5
4.7
ICC1
4.4
5.7
ICC2
13.9
16.4
10 Mbps
100 Mbps
(1)
TYP
EN2 = 0 V, VI = 0 V (Devices with suffix
F), VI = VCCI (1) (Devices without suffix F)
1 Mbps
All channels switching
with square wave clock
input;
CL = 15 pF
MIN
UNIT
mA
mA
mA
mA
mA
mA
mA
VCCI = Input-side VCC; VCCO = Output-side VCC.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
11
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
6.15 Switching Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
MIN
TYP
MAX
6
11
16
ns
0.55
4.1
ns
2.5
ns
4.5
ns
1.7
3.9
ns
1.9
3.9
ns
tPHZ
Disable propagation delay, high-to-high impedance
output
12
20
ns
tPLZ
Disable propagation delay, low-to-high impedance
output
12
20
ns
10
20
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840F
10
20
ns
0.2
9
μs
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
Same-direction channels
See Figure 11
Enable propagation delay, high impedance-to-high
output for ISO7840F
tPZL
tfs
Default output delay time from input power loss
tie
(3)
See Figure 11
Enable propagation delay, high impedance-to-high
output for ISO7840
tPZH
(1)
(2)
TEST CONDITIONS
See Figure 12
Measured from the time VCC goes below 1.7 V. See
Figure 13
16
Time interval error
UNIT
2
0.90
– 1 PRBS data at 100 Mbps
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
6.16 Switching Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
MIN
TYP
MAX
6
10.8
16
ns
0.7
4.2
ns
2.2
ns
4.5
ns
0.8
3
ns
0.8
3
ns
tPHZ
Disable propagation delay, high-to-high impedance
output
17
32
ns
tPLZ
Disable propagation delay, low-to-high impedance
output
17
32
ns
17
32
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840F
17
32
ns
0.2
9
μs
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
tPZH
tPZL
tfs
tie
(1)
(2)
(3)
12
TEST CONDITIONS
See Figure 11
Same-direction channels
See Figure 11
Enable propagation delay, high impedance-to-high
output for ISO7840
Enable propagation delay, high impedance-to-high
output for ISO7840F
Default output delay time from input power loss
Time interval error
UNIT
See Figure 12
Measured from the time VCC goes below 1.7 V.
See Figure 13
16
2
0.91
– 1 PRBS data at 100 Mbps
ns
Also known as Pulse Skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
ISO7840, ISO7840F
www.ti.com
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
6.17 Switching Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ±10% (over recommended operating conditions unless otherwise noted)
PARAMETER
MIN
TYP
MAX
UNIT
7.5
11.7
17.5
ns
0.66
4.2
ns
2.2
ns
4.5
ns
1
3.5
ns
1.2
3.5
ns
tPHZ
Disable propagation delay, high-to-high impedance
output
22
45
ns
tPLZ
Disable propagation delay, low-to-high impedance
output
22
45
ns
18
45
ns
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840
2
2.5
μs
Enable propagation delay, high impedance-to-low
output for ISO7840F
18
45
ns
0.2
9
μs
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
tPZH
tPZL
tfs
tie
(1)
(2)
(3)
TEST CONDITIONS
See Figure 11
Same-direction Channels
See Figure 11
Enable propagation delay, high impedance-to-high
output for ISO7840
Enable propagation delay, high impedance-to-high
output for ISO7840F
Default output delay time from input power loss
See Figure 12
Measured from the time VCC goes below 1.7 V.
See Figure 13
16
Time interval error
2
– 1 PRBS data at 100 Mbps
0.91
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: ISO7840 ISO7840F
Submit Documentation Feedback
13
ISO7840, ISO7840F
SLLSEN2B – JULY 2015 – REVISED APRIL 2016
www.ti.com
6.18 Insulation Characteristics Curves
1.E+11
87.5%
1.E+9
1.E+9
1.E+8
1.E+8
1.E+7
1.E+6
1.E+5
Safety Margin Zone: 2400 VRMS, 63 Years
Operating Zone: 2000 VRMS, 34 Years
TDDB Line (