ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
ISOW774x Quad-Channel Digital Isolator with Integrated Low-Emissions, Low-Noise
DC-DC Converter
1 Features
2 Applications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
100 Mbps data rate
Integrated DC-DC converter with low-emissions,
low-noise
– Emission optimized to meet CISPR 32 and EN
55032 Class B with >5 dB margin on 2 layer
board
– Low frequency power converter at 25 MHz
enabling low noise performance
– Low output ripple: 24 mV
High efficiency output power
– Efficiency at max load: 46%
– Up to 0.55-W output power
– VISOOUT accuracy of 5%
– 5 V to 5 V: Max available load current = 110 mA
– 5 V to 3.3 V: Max available load current = 140
mA
– 3.3 V to 3.3 V: Max available load current = 60
mA
Independent power supply for channel isolator &
power converter
– Logic supply (VIO): 1.71-V to 5.5-V
– Power converter supply (VDD): 3-V to 5.5-V
Robust electromagnetic compatibility (EMC)
– System-level ESD, EFT, and surge immunity
– ±8 kV IEC 61000-4-2 contact discharge
protection across isolation barrier
Reinforced and Basic isolation options
High CMTI: 100-kV/µs (typical)
Safety Related Certifications:
– VDE reinforced and basic insulation per DIN
VDE V 0884-11:2017-01
– UL 1577 component recognition program
– IEC 62368-1, IEC 61010-1, IEC 60601-1 and
GB 4943.1-2011 certifications
– ISOW774xB devices are planned
Extended temperature range: –40°C to +125°C
20-pin wide body SOIC package
Factory automation
Motor control
Grid infrastructure
Medical equipment
Test and measurement
3 Description
The ISOW77xx family of devices are galvanicallyisolated quad-channel digital isolator with an
integrated high-efficiency power converter with low
emissions. The integrated DC-DC converter provides
up to 550 mW of isolated power, eliminating the
need for a separate isolated power supply in spaceconstrained isolated designs.
Device Information
FEATURE
ISOW774x
ISOW774xF
ISOW774xB
ISOW774xFB
Protection Level
Reinforced
Basic
Surge Test Voltage
10 kVPK
7.8 kVPK
Isolation Rating
5000 VRMS
5000 VRMS
Working Voltage
1000 VRMS/
1500VPK
1000 VRMS/
1500VPK
Package
DFM (20)
DFM (20)
Body Size (Nom)
12.83 mm × 7.5
mm
12.83 mm × 7.5
mm
VISOIN
VIO
INA
Tx
Rx
EN_IO2
OUTA
INB
Tx
Rx
OUTB
INC
Tx
Rx
OUTC
OUTD
Rx
Tx
IND
EN_IO1
GISOIN
GNDIO
GND1
GN
D2
VSEL
VDD
EN/FLT
DC-DC
Primary
DC-DC
Secondary
GND1
VISOOUT
GND2
ISOW7741 Simplified Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Description (continued).................................................. 3
6 Pin Configuration and Functions...................................4
7 Specifications.................................................................. 8
7.1 Absolute Maximum Ratings........................................ 8
7.2 ESD Ratings............................................................... 8
7.3 Recommended Operating Conditions.........................9
7.4 Thermal Information..................................................10
7.5 Power Ratings...........................................................10
7.6 Insulation Specifications............................................11
7.7 Safety-Related Certifications.................................... 12
7.8 Safety Limiting Values...............................................12
7.9 Electrical Characteristics - Power Converter............ 13
7.10 Supply Current Characteristics - Power
Converter.....................................................................14
7.11 Electrical Characteristics Channel Isolator VIO, VISOIN = 5-V..........................................................15
7.12 Supply Current Characteristics Channel
Isolator - VIO, VISOIN = 5-V...........................................15
7.13 Electrical Characteristics Channel Isolator VIO, VISOIN = 3.3-V.......................................................18
7.14 Supply Current Characteristics Channel
Isolator - VIO, VISOIN = 3.3-V........................................18
7.15 Electrical Characteristics Channel Isolator VIO, VISOIN = 2.5-V.......................................................21
7.16 Supply Current Characteristics Channel
Isolator - VIO, VISOIN = 2.5-V........................................21
7.17 Electrical Characteristics Channel Isolator VIO, VISOIN = 1.8-V.......................................................24
7.18 Supply Current Characteristics Channel
Isolator - VIO, VISOIN = 1.8-V........................................24
7.19 Switching Characteristics - 5-V Supply................... 27
7.20 Switching Characteristics - 3.3-V Supply................ 28
7.21 Switching Characteristics - 2.5-V Supply................ 29
7.22 Switching Characteristics - 1.8-V Supply................ 30
7.23 Insulation Characteristics Curves........................... 31
7.24 Typical Characteristics............................................ 32
8 Parameter Measurement Information.......................... 38
9 Detailed Description......................................................40
9.1 Overview................................................................... 40
9.2 Functional Block Diagram......................................... 41
9.3 Feature Description...................................................42
9.4 Device Functional Modes..........................................45
10 Application and Implementation................................ 47
10.1 Application Information........................................... 47
10.2 Typical Application.................................................. 47
11 Power Supply Recommendations..............................51
12 Layout...........................................................................52
12.1 Layout Guidelines................................................... 52
12.2 Layout Example...................................................... 53
13 Device and Documentation Support..........................54
13.1 Device Support....................................................... 54
13.2 Documentation Support.......................................... 54
13.3 Receiving Notification of Documentation Updates..54
13.4 Support Resources................................................. 54
13.5 Trademarks............................................................. 54
13.6 Electrostatic Discharge Caution..............................54
13.7 Glossary..................................................................54
14 Mechanical, Packaging, and Orderable
Information.................................................................... 55
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (January 2022) to Revision C (April 2022)
Page
• Added ISOW7740, ISOW7742, ISOW7743 and ISOW7744 Typical Characteristics....................................... 32
Changes from Revision A (October 2021) to Revision B (January 2022)
Page
• Added ISOW7740, ISOW7742, ISOW7743, and ISOW7744 to data sheet....................................................... 1
Changes from Revision * (September 2021) to Revision A (October 2021)
Page
• Updated device status to Production Data......................................................................................................... 1
2
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
5 Description (continued)
The high-efficiency of the power converter allows for operation at a wide operating ambient temperature range
of –40°C to +125°C. This device provides improved emissions performance, allowing for simplified board design
and has provisions for ferrite beads to further attenuate emissions. The ISOW774x has been designed with
enhanced protection features in mind, including soft-start to limit inrush current, over-voltage and under-voltage
lock out, fault detection on the EN/FLT pin, overload and short-circuit protection, and thermal shutdown.
The ISOW77xx family of devices provide high electromagnetic immunity while isolating CMOS or LVCMOS
digital I/Os. The signal-isolation channel has a logic input and output buffer separated by a double capacitive
silicon dioxide (SiO2) insulation barrier, whereas, power isolation uses on-chip transformers separated by thin
film polymer as insulating material. There are five orderable configurations of four channel ISOW77xx flavor
using the last part number digit to note the number of reverse channels. For example, the ISOW7740 has 4
forward channels and 0 reverse channels, while the ISOW7743 would have 1 forward channel and 3 reverse
channels. If the input signal is lost, the default output is high for the ISOW77xx devices without the F suffix and
low for the ISOW77xx devices with the F suffix. The ISOW774x can operate from a single supply voltage of 3 V
to 5.5 V by connecting VIO and VDD together on PCB. If lower logic levels are required, these devices support
1.71 V to 5.5 V logic supply (VIO) that can be independent from the power converter supply (VDD) of 3 V to 5.5 V.
VISOIN and VISOOUT needs to be connected on board with either a ferrite bead or fed through a LDO.
These devices help prevent noise currents on data buses, such as UART, SPI, RS-485, RS-232, and CAN,
or other circuits from entering the local ground and interfering with or damaging sensitive circuitry. Through
innovative chip design and layout techniques, electromagnetic compatibility of the device has been significantly
enhanced to ease system-level ESD, EFT, surge and emissions compliance. The device is available in a 20-pin
SOIC wide-body (SOIC-WB) DFM package.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
3
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
6 Pin Configuration and Functions
1
20
VISOIN
INA
2
19
OUTA
INB
3
18
OUTB
INC
4
17
OUTC
IND
5
16
OUTD
GNDIO
6
15
GISOIN
EN_IO1
7
14
EN_IO2
EN/FLT
8
13
VSEL
VDD
9
12
VISOOUT
GND1
10
11
GND2
I S O LAT I O N
VIO
Figure 6-1. ISOW7740 DFM Package 20-Pin SOIC-WB Top View
1
20
VISOIN
INA
2
19
OUTA
INB
3
18
OUTB
INC
4
17
OUTC
OUTD
5
16
IND
GNDIO
6
15
GISOIN
EN_IO1
7
14
EN_IO2
EN/FLT
8
13
VSEL
VDD
9
12
VISOOUT
GND1
10
11
GND2
I S O LAT I O N
VIO
Figure 6-2. ISOW7741 DFM Package 20-Pin SOIC-WB Top View
4
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
1
20
VISOIN
INA
2
19
OUTA
INB
3
18
OUTB
OUTC
4
17
INC
OUTD
5
16
IND
GNDIO
6
15
GISOIN
EN_IO1
7
14
EN_IO2
EN/FLT
8
13
VSEL
VDD
9
12
VISOOUT
GND1
10
11
GND2
I S O LAT I O N
VIO
Figure 6-3. ISOW7742 DFM Package 20-Pin SOIC-WB Top View
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
5
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
1
20
VISOIN
INA
2
19
OUTA
OUTB
3
18
INB
OUTC
4
17
INC
OUTD
5
16
IND
GNDIO
6
15
GISOIN
EN_IO1
7
14
EN_IO2
EN/FLT
8
13
VSEL
VDD
9
12
VISOOUT
GND1
10
11
GND2
I S O LAT I O N
VIO
Figure 6-4. ISOW7743 DFM Package 20-Pin SOIC-WB Top View
1
20
VISOIN
OUTA
2
19
INA
OUTB
3
18
INB
OUTC
4
17
INC
OUTD
5
16
IND
GNDIO
6
15
GISOIN
EN_IO1
7
14
EN_IO2
EN/FLT
8
13
VSEL
VDD
9
12
VISOOUT
GND1
10
11
GND2
I S O LAT I O N
VIO
Figure 6-5. ISOW7744 DFM Package 20-Pin SOIC-WB Top View
PIN
NAME
6
NO.
I/O
DESCRIPTION
ISOW7740
ISOW7741
ISOW7742
ISOW7743
ISOW7744
GNDIO
6
6
6
6
6
—
Ground connection for VIO. GND1 and GNDIO needs to
be shorted on board.
GND1
10
10
10
10
10
—
Ground connection for VDD. GND1 and GNDIO needs to
be shorted on board.
GND2
11
11
11
11
11
—
Ground connection for VISOOUT. GND2 and GISOIN pins
can be shorted on board or connected through a ferrite
bead. See the Layout Section for more information.
GISOIN
15
15
15
15
15
—
Ground connection for VISOIN. GND2 and GISOIN pins
can be shorted on board or connected through a ferrite
bead. See the Layout Section for more information.
INA
2
2
2
2
19
I
Submit Document Feedback
Input channel A
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
PIN
NAME
NO.
I/O
DESCRIPTION
ISOW7740
ISOW7741
ISOW7742
ISOW7743
ISOW7744
INB
3
3
3
18
18
I
Input channel B
INC
4
4
17
17
17
I
Input channel C
IND
5
16
16
16
16
I
Input channel D
OUTA
19
19
19
19
2
O
Output channel A
OUTB
18
18
18
3
3
O
Output channel B
OUTC
17
17
4
4
4
O
Output channel C
OUTD
16
5
5
5
5
O
Output channel D
I
Output Enable 1: When EN_IO1 is high or open then the
channel output pins on side 1 are enabled. When EN_IO1
is low then the channel output pins on side 1 are in a high
impedance state and the transmitter of the channel input
pins on side 1 are disabled.
I
Output Enable 2: When EN_IO2 is high or open then the
channel output pins on side 2 are enabled. When EN_IO2
is low then the channel output pins on side 2 are in a high
impedance state and the transmitter of the channel input
pins on side 2 are disabled.
EN_IO1
EN_IO2
7
14
7
14
7
14
7
14
7
14
Multi-function power converter enable input pin or fault
output pin. Can only be used as either an input pin or an
output pin.
Power converter enable input pin: enables and disables
the integrated DC-DC power converter. Connect directly
to microcontroller or through a series current limiting
resistor to use as an enable input pin. DC-DC power
EN/FLT
8
8
8
8
8
I/O
converted is enabled when EN/FLT is high to the VIO
voltage level and disabled when low at GND1 voltage
level.
Fault output pin: Alert signal if power converter is not
operating properly. This pin is active low. Connect to
microcontroller through a 5 kΩ or greater pull-up resistor
in order to use as a fault outpin pin.
See Section 9.3.3 for more information
VISOOUT selection pin. VISOOUT = 5 V when VSEL shorted
to VISOOUT. VISOOUT = 3.3 V, when VSEL shorted to
GND2. For more information see the Device Functional
Modes.
VSEL
13
13
13
13
13
I
VIO
1
1
1
1
1
—
Side 1 logic supply.
VDD
9
9
9
9
9
—
Side 1 DC-DC converter power supply.
VISOIN
20
20
20
20
20
—
Side 2 supply voltage for isolation channels. VISOIN
and VISOOUT pins can be shorted on board or
connected through a ferrite bead. See Application and
Implementation for more information.
VISOOUT
12
12
12
12
12
—
Isolated power converter output voltage. VISOIN
and VISOOUT pins can be shorted on board or
connected through a ferrite bead. See Application and
Implementation for more information.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
7
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1) (2)
MIN
MAX
UNIT
VDD
Power converter supply voltage
–0.5
6
V
VISOIN
Isolated supply voltage, input supply for secondary side isolation channels
–0.5
6
V
VISOOUT
Isolated supply voltage, Power converter output
VSEL shorted to GND2
–0.5
4
V
VISOOUT
Isolated supply voltage, Power converter output
VSEL shorted to VISOOUT
–0.5
6
V
VIO
Primary side logic supply voltage
–0.5
6
V
Voltage at INx, OUTx, EN_IOx(3)
–0.5
VSI + 0.5
V
Voltage at EN/FLT
–0.5
VSI + 0.5
V
Voltage at VSEL
–0.5
VISOOUT + 0.5
V
IO
Maximum output current through data channels
–15
15
mA
TJ
Junction temperature
–40
150
°C
Tstg
Storage temperature
–65
150
°C
V
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated
under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
VDD, VISOIN VISOOUT, and VIO are with respect to the local ground pin (GND1 or GND2). All voltage values except differential I/O bus
voltages are peak voltage values.
VSI = input side supply; Cannot exceed 6 V.
7.2 ESD Ratings
VALUE
V(ESD)
Electrostatic
discharge
Human-body model (HBM), per AEC Q100-002(1)
HBM ESD Classification Level 2
±3000
Charged-device model (CDM), per AEC Q100-011
CDM ESD Classification Level C6
±1500
61000-4-2(2)
Contact discharge per IEC
Isolation barrier withstand test
(1)
(2)
8
UNIT
V
±8000
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
IEC ESD strike is applied across the barrier with all pins on each side tied together creating a two-terminal device.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.3 Recommended Operating Conditions
Over recommended operating conditions, typical values are at VDD = VIO = 3.3 V and TA =25°C, GND1 = GNDIO, GND2 =
GISOIN (unless otherwise noted)
MIN
NOM
MAX
UNIT
2.97
3.3
3.63
V
4.5
5
5.5
V
2.7
2.95
V
Power Converter
3.3 V operation
VDD
Power converter supply
voltage
VDD(UVLO+)
Positive threshold when
power converter supply is
rising
Positive threshold when power
converter supply is rising
VDD(UVLO-)
Positive threshold when
power converter supply is
falling
Positive threshold when power
converter supply is falling
2.40
VDD(HYS)
Power converter supply
voltage hysteresis
Power converter supply voltage
hysteresis
0.15
1.8 V operation
1.71
2.5 V, 3.3 V, and 5 V operation
2.25
5 V operation
2.55
V
V
Channel Isolation
VIO, VISOIN
(3)
Channel logic supply voltage
V
5.5
V
1.7
V
VIO(UVLO+)
Rising threshold of logic supply voltage
VIO(UVLO-)
Falling threshold of logic supply voltage
1.0
VIO(HYS)
Logic supply voltage hysteresis
75
mV
VISOIN = 5 V
–4
mA
VISOIN = 3.3 V
–2
mA
VISOIN = 2.5 V
–1
mA
VISOIN = 1.8 V
–1
mA
High level output current(1)
IOH
Low level output current(1)
IOL
High-level input
VIL
Low-level input voltage
DR
Data rate
tPWRUP
Channel isolator ready after
power up or EN/FLT high
TA
Ambient temperature
(1)
(2)
(3)
1.41
V
VISOIN = 5 V
4
mA
VISOIN = 3.3 V
2
mA
VISOIN = 2.5 V
1
mA
VISOIN = 1.8 V
1
mA
voltage(2)
VIH
1.55
1.89
0.7 × VSI
VSI
V
0
0.3 × VSI
V
100
VISOIN > VIO(UVLO+)
5
–40
Mbps
ms
125
°C
This current is for data output channel.
VSI = input side supply; VSO = output side supply
The channel outputs are in undetermined state when 1.89 V < VSI < 2.25 V and 1.05 V < VSI < 1.71 V
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
9
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.4 Thermal Information
ISOW774x
THERMAL
METRIC(1)
UNIT
DFM (SOIC)
20 PINS
RθJA
Junction-to-ambient thermal resistance
68.5
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
24.6
°C/W
RθJB
Junction-to-board thermal resistance
53.7
°C/W
ΨJT
Junction-to-top characterization parameter
17.1
°C/W
ΨJB
Junction-to-board characterization parameter
50.9
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
—
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.5 Power Ratings
VDD = VIO = 5.5 V, IISO = 110 mA, TJ = 150°C, TA ≤ 80°C, CL = 15 pF, input a 50-MHz 50% duty-cycle square wave
PARAMETER
PD
PD1
PD2
10
TEST CONDITIONS
MIN
TYP
Maximum power dissipation (both sides) VDD = 5.5 V, VIO = 5.5 V, VISOOUT =
VISOIN, IISOOUT = 100 mA, TJ = 150°C,
Maximum power dissipation (side-1)
TA ≤ 80°C, CL = 15 pF, input a 50-MHz
Maximum power dissipation (side-2)
50% duty-cycle square wave
Submit Document Feedback
MAX
UNIT
1.48
W
0.74
W
0.74
W
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.6 Insulation Specifications
PARAMETER
TEST CONDITIONS
VALUE
UNIT
GENERAL
CLR
External clearance(1)
Shortest terminal-to-terminal distance through air
>8
mm
CPG
External creepage(1)
Shortest terminal-to-terminal distance across the
package surface
>8
mm
DTI
Minimum internal gap (internal clearance – capacitive
signal isolation)
> 17
Minimum internal gap (internal clearance –
transformer power isolation)
>120
Comparative tracking index
DIN EN 60112 (VDE 0303-11); IEC 60112
> 600
Material group
According to IEC 60664-1
Distance through the insulation
CTI
Overvoltage category per IEC 60664-1
DIN VDE V
µm
V
I
Rated mains voltage ≤ 300 VRMS
I-IV
Rated mains voltage ≤ 600 VRMS
I-IV
Rated mains voltage ≤ 1000 VRMS
I-III
0884-11:2017-01(2)
VIORM
Maximum repetitive peak isolation
voltage
VIOWM
Maximum working isolation voltage
AC voltage (bipolar)
1500
VPK
AC voltage; Time dependent dielectric breakdown
(TDDB) Test
1000
VRMS
DC voltage
1500
VDC
7071
VPK
VIOTM
Maximum transient isolation voltage
VTEST = VIOTM; t = 60 s (qualification);
VTEST = 1.2 × VIOTM; t = 1 s (100% production)
VIOSM
Maximum surge isolation voltage
ISOW774x(3)
Test method per IEC 62368-1, 1.2/50 µs waveform,
VTEST = 1.6 × VIOSM = 10000 VPK(qualification)
6250
VPK
VIOSM
Maximum surge isolation voltage
ISOW774xB(3)
Test method per IEC 62368-1, 1.2/50 µs waveform,
VTEST = 1.3 × VIOSM = 7800 VPK(qualification)
6000
VPK
Apparent charge(4)
qpd
Barrier capacitance, input to output(5)
CIO
Insulation resistance(5)
RIO
Method a, after input/output safety test subgroup 2/3,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.2 × VIORM, tm = 10 s
≤5
Method a, after environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s; ISOW774x: Vpd(m) = 1.6 ×
VIORM, tm = 10 s, ISOW774xB: Vpd(m) = 1.2 × VIORM, tm
= 10 s
≤5
Method b1, at routine test (100% production) and
preconditioning (type test),
Vini = 1.2 × VIOTM, tini = 1 s;
ISOW774x: Vpd(m) = 1.875 × VIORM, tm = 1
s, ISOW774xB: Vpd(m) = 1.5 × VIORM, tm = 1 s
≤5
VIO = 0.4 × sin (2πft), f = 1 MHz
~3.5
pC
VIO = 500 V, TA = 25°C
>
VIO = 500 V, 100°C ≤ TA ≤ 125°C
> 1011
VIO = 500 V, TS = 150°C
>
pF
1012
Ω
109
Pollution degree
2
Climatic category
40/125/21
UL 1577
VISO(UL)
(1)
Withstand isolation voltage
VTEST = VISO(UL)= 5000 VRMS, t = 60 s (qualification),
VTEST = 1.2 × VISO(UL) = 6000 VRMS, t = 1 s (100%
production)
5000
VRMS
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application.
Care should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the
isolator on the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal
in certain cases. Techniques such as inserting grooves, ribs, or both on a printed circuit board are used to help increase these
specifications.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
11
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
(2)
(3)
(4)
(5)
ISOW77xx is suitable for safe electrical insulation and ISOW77xxB is suitable for basic electrical insulation only within the safety
ratings.. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.
Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-terminal device.
7.7 Safety-Related Certifications
VDE
CSA
UL
Certified according to DIN Certified according to IEC
VDE V 0884-11:2017-01
62368-1, and IEC 60601-1
Recognized under
UL 1577 Component
Recognition Program
CQC
TUV
Certified according to
GB 4943.1-2011
Certified according to
EN 61010-1:2010/A1:2019
and EN 62368-1:2014
Reinforced insulation;
Maximum transient
isolation voltage, 7071
VPK;
Maximum repetitive peak
isolation voltage, 1500
VPK;
Maximum surge
isolation voltage, 6250
VPK for ISOW774x
(Reinforced), 6000
VPK for ISOW774xB
(Basic).
CSA 62368-1-19 and IEC
62368-1:2018 Ed. 3 and EN
62368-1:2020. (pollution degree
2, material group I) 600
VRMS (ISOW774x Reinforced),
1000VRMS (ISOW774xB Basic)
maximum working voltage;
Single protection, 5000
2 MOPP (Means of Patient
VRMS
Protection) per CSA 60601-1:14
and IEC 60601-1 Ed. 3+A1,
250 VRMS maximum working
voltage. Temperature rating is
90°C for reinforced insulation
and 125°C for basic insulation;
see certificate for details.
5000 VRMS Reinforced
insulation per EN 610101:2010 up to working
Reinforced Insulation,
voltage of 600 VRMS;
Altitude ≤ 5000 m,
5000 VRMS Reinforced
insulation per EN
Tropical Climate, 700
VRMS maximum working 62368-1:2014 up to
voltage;
working voltage of
600 VRMS (ISOW774x
Reinforced), 1000
VRMS (ISOW774xB Basic)
Certificate #: Reinforced:
40040142
Basic: 40047657
Master Contract#: 220991
Certificate #:
CQC21001297517
File #: E181974
Client ID: 77311
7.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry.
PARAMETER
IS
Safety input, output, or supply
TEST CONDITIONS
current(1)
PS
Safety input, output, or total power(1)
TS
Maximum safety temperature(1)
(1)
12
MIN
TYP
MAX
UNIT
RθJA = 68.5°C/W, VI = 5.5 V, TJ = 150°C,
TA = 25°C
332
RθJA = 68.5°C/W, VI = 3.6 V, TJ = 150°C,
TA = 25°C
507
RθJA = 68.5°C/W, TJ = 150°C, TA = 25°C
1825
mW
150
°C
mA
The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The
IS and PS parameters represent the safety current and safety power respectively. The maximum limits of IS and PS should not be
exceeded. These limits vary with the ambient temperature, TA.
The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for
leaded surface-mount packages. Use the following equations to calculate the value for each parameter:
TJ = TA + RθJA × P, where P is the power dissipated in the device.
TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum allowed junction temperature.
PS = IS × VI, where VI is the maximum input voltage.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.9 Electrical Characteristics - Power Converter
VDD = 5 V ±10% or 3.3 V ±10% and VISOIN power externally, GND1 = GNDIO, GND2 = GISOIN (over recommended
operating conditions, unless otherwise specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VDD = 5 V, VISOOUT = 5 V, VSEL = VISOOUT
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 55 mA
4.75
5
5.25
V
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 110 mA
4.5
5
5.25
V
VISOOUT(LINE
DC line regulation
IISOOUT = 55 mA, VDD = 4.5 V to 5.5 V
DC load regulation
IISOOUT = 0 to 110 mA
EFF
Efficiency at maximum load
current (1)
IISOOUT = 110 mA, CLOAD = 0.01 µF || 10 µF;
VI = VDD (ISOW774x); VI =0 V (ISOW774x
with F suffix).
VISOOUT(RIP)
Output ripple on isolated supply
(pk-pk)
20-MHz bandwidth, CLOAD = 0.01 µF || 20 µF,
IISOOUT = 110 mA
IISOOUT_SC
DC current from VDD supply
under short circuit on VISOOUT
VISOOUT shorted to GND2
)
VISOOUT(LOA
D)
2
mV/V
1%
46%
24
mV
250
mA
VDD = 5 V, VISOOUT = 3.3 V, VSEL = GND2
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 70 mA
3.135
3.3
3.465
V
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 140 mA
3.135
3.3
3.465
V
VISOOUT(LINE
DC line regulation
IISOOUT = 70 mA, VDD = 4.5 V to 5.5 V
DC load regulation
IISOOUT = 0 to 140 mA
EFF
Efficiency at maximum load
current (1)
IISOOUT = 140 mA, CLOAD = 0.01 µF || 10 µF;
VI = VDD (ISOW774x); VI =0 V (ISOW774x
with F suffix).
VISOOUT(RIP)
Output ripple on isolated supply
(pk-pk)
20-MHz bandwidth , CLOAD = 0.01 µF || 20 µF,
IISOOUT = 110 mA
IISOOUT_SC
DC current from VDD supply
under short circuit on VISOOUT
VISOOUT shorted to GND2
)
VISOOUT(LOA
D)
2
mV/V
1%
36%
30
mV
250
mA
VDD = 3.3 V, VISOOUT = 3.3 V, VSEL = GND2
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 30 mA
3.135
3.3
3.465
V
VISOOUT
Isolated supply voltage
External IISOOUT = 0 to 60 mA
3.135
3.3
3.465
V
VISOOUT(LINE
DC line regulation
IISOOUT = 30 mA, VDD = 3.0 V to 3.6 V
DC load regulation
IISOOUT = 0 to 60 mA
EFF
Efficiency at maximum load
current (1)
IISOOUT = 60 mA, CLOAD = 0.01 µF || 10 µF;
VI = VDD (ISOW774x); VI =0 V (ISOW774x
with F suffix).
VISOOUT(RIP)
Output ripple on isolated supply
(pk-pk)
20-MHz bandwidth, CLOAD = 0.01 µF || 20 µF,
IISOOUT = 60 mA
IISOOUT_SC
DC current from VDD supply
under short circuit on VISOOUT
VISOOUT shorted to GND2
)
VISOOUT(LOA
D)
(1)
2
mV/V
1%
43%
14
mV
185
mA
Power converter ILOAD = current required to power the secondary side. ILOAD does not take into account the channel isolator current.
See Supply Current Characteristics Channel Isolator section for details.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
13
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.10 Supply Current Characteristics - Power Converter
VDD = 5 V ±10% or 3.3 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions unless otherwise
noted).
PARAMETER
TEST CONDITIONS
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
Power Converter Disabled
Power converter supply
current
EN/FLT = GND1, VISOOUT = No ILOAD
IDD
0.28
0.45
mA
Logic supply current
EN/FLT = GND1
IIO
0.27
0.57
mA
Power Converter Enabled
Power converter supply
current input
Power converter output
current (1)
(1)
14
VDD = 5 V, VSEL = VISOOUT
ILOAD = 55 mA
115
171
mA
VDD = 5 V, VSEL = VISOOUT
ILOAD = 110 mA
225
316
mA
VDD = 5 V, VSEL = GND2
ILOAD = 70 mA
127
169
mA
VDD = 5 V, VSEL = GND2
ILOAD = 140 mA
250
310
mA
VDD = 3.3 V, VSEL = GND2
ILOAD = 30 mA
74
112
mA
VDD = 3.3 V, VSEL = GND2
ILOAD = 60 mA
143
216
mA
VDD = 5 V
VSEL = VISOOUT
VDD = 5 V
VSEL = GND2
VDD = 3.3 V
VSEL = GND2
IDD
IISOOUT
110
mA
140
mA
60
mA
ILOAD does not take into account the channel isolator current. See Supply Current Characteristics Channel Isolator section for details.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.11 Electrical Characteristics Channel Isolator - VIO, VISOIN = 5-V
VIO, VISOIN = 5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Channel Isolation
VITH
Input pin rising threshold
VITL
Input pin falling threshold
0.3 x VSI
V
VI(HYS)
Input pin threshold hysteresis
(INx)
0.1 x VSI
V
IIL
Low level input current
–25
µA
IIH
0.7 x VSI
VIL = 0 at INx
(1)
High level input current
VIH = VSI
VOH
High level output voltage
IO = –4 mA, see Switching Characteristics
Test Circuit and Voltage Waveforms
VOL
Low level output voltage
IO = 4 mA, see Switching Characteristics Test
Circuit and Voltage Waveforms
CMTI
Common mode transient
immunity
VI = VSI or 0 V, VCM = 1000 V; see CommonMode Transient Immunity Test Circuit
(1)
at INx
V
25
µA
VSO (1) –
0.4
V
0.4
85
V
100
kV/us
VSI = input side supply; VSO = output side supply
7.12 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 5-V
VIO, VISOIN = 5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
ISOW7740 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.5
3.6
mA
IISOIN
4.6
6.9
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
2.5
3.6
mA
IISOIN
4.6
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.5
3.6
mA
IISOIN
4.6
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
6.9
9.2
mA
IISOIN
4.8
7.2
mA
IDD_IO
4.7
6.4
mA
IISOIN
4.8
7
mA
IDD_IO
4.9
6.7
mA
IISOIN
7.3
9.7
mA
IDD_IO
6.5
8.4
mA
IISOIN
31
35
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.8
4.1
mA
IISOIN
4.3
6.3
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
2.8
4.1
mA
IISOIN
4.3
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.8
4.1
mA
IISOIN
4.3
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
6.1
8.4
mA
IISOIN
5.5
7.9
mA
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7741 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
15
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
IDD_IO
4.4
6.3
mA
IISOIN
4.9
7.1
mA
IDD_IO
5
7
mA
IISOIN
6.3
8.9
mA
IDD_IO
12.2
14.2
mA
IISOIN
25
32
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.7
mA
IISOIN
3.9
5.6
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
3.1
4.7
mA
IISOIN
3.9
5.6
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.7
mA
IISOIN
3.9
5.6
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
5.4
7.7
mA
IISOIN
6.2
8.5
mA
IDD_IO
4.2
6.3
mA
IISOIN
5.1
7.2
mA
IDD_IO
5.5
7.6
mA
IISOIN
6.3
8.3
mA
IDD_IO
16.7
20
mA
IISOIN
17.33
22
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.5
5.2
mA
IISOIN
3.6
5.1
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
3.5
5.2
mA
IISOIN
3.6
5.1
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.5
5.2
mA
IISOIN
3.6
5.1
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
4.7
6.9
mA
IISOIN
7
9.4
mA
IDD_IO
4
6.2
mA
IISOIN
5.3
7.2
mA
IDD_IO
6
8.2
mA
IISOIN
6.2
8
mA
IDD_IO
24
27
mA
IISOIN
14
17
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
IDD_IO
3.8
5.8
mA
IISOIN
3.3
4.6
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.8
5.8
mA
IISOIN
3.3
4.6
mA
100 Mbps
ISOW7742 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7743 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7744 Channel Supply Current
Supply current - Disable
16
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
Channel Supply current DC signal
TEST CONDITIONS
TYP
MAX
UNIT
IDD_IO
3.8
5.8
mA
IISOIN
3.3
4.6
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
4
6.2
mA
IISOIN
7.7
10.2
mA
IDD_IO
3.8
6.1
mA
IISOIN
5.5
7.3
mA
IDD_IO
6.4
8.6
mA
IISOIN
5.6
7.3
mA
IDD_IO
30
34
mA
IISOIN
7.4
9
mA
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
(1)
MIN
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
VCCI = VIO or VISOIN
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
17
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.13 Electrical Characteristics Channel Isolator - VIO, VISOIN = 3.3-V
VIO, VISOIN = 3.3 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Channel Isolation
VITH
Input pin rising threshold
VITL
Input pin falling threshold
0.3 x VSI
V
VI(HYS)
Input pin threshold hysteresis
(INx)
0.1 x VSI
V
IIL
Low level input current
-25
µA
IIH
0.7 x VSI
VIL = 0 at INx
(1)
High level input current
VIH = VSI
VOH
High level output voltage
IO = –2 mA, see Switching Characteristics
Test Circuit and Voltage Waveforms
VOL
Low level output voltage
IO = 2 mA, see Switching Characteristics Test
Circuit and Voltage Waveforms
CMTI
Common mode transient
immunity
VI = VSI or 0 V, VCM = 1000 V; see CommonMode Transient Immunity Test Circuit
(1)
at INx
V
25
µA
VSO (1) –
0.3
V
0.3
85
V
100
kV/us
VSI = input side supply; VSO = output side supply
7.14 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 3.3-V
VIO, VISOIN = 3.3 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
ISOW7740 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.4
3.5
mA
IISOIN
4.6
6.9
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
2.4
3.5
mA
IISOIN
4.5
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.4
3.5
mA
IISOIN
4.5
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
6.8
9.1
mA
IISOIN
4.8
7.2
mA
IDD_IO
4.6
6.4
mA
IISOIN
4.7
7
mA
IDD_IO
4.7
6.4
mA
IISOIN
6
8.6
mA
IDD_IO
5.5
7.8
mA
IISOIN
22
30
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.8
4
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
2.8
4
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.8
4
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
6.1
8.3
mA
IISOIN
5.5
7.9
mA
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7741 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
18
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 3.3 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
TYP
MAX
IDD_IO
4.4
6.3
mA
IISOIN
4.9
7.1
mA
IDD_IO
4.8
6.7
mA
IISOIN
5.9
8.3
mA
IDD_IO
9.4
12
mA
IISOIN
17.5
25
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.9
5.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.9
5.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.9
5.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
5.4
7.6
mA
IISOIN
6.2
8.5
mA
IDD_IO
4.2
6.3
mA
IISOIN
5.1
7.2
mA
IDD_IO
4.9
7
mA
IISOIN
5.7
7.9
mA
IDD_IO
13
16.6
mA
IISOIN
13.7
17.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.6
5
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.6
5
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.6
5
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
4.7
6.8
mA
IISOIN
6.9
9.3
mA
IDD_IO
4
6.2
mA
IISOIN
5.3
7.2
mA
IDD_IO
5
7.4
mA
IISOIN
5.6
7.6
mA
IDD_IO
17
23
mA
IISOIN
10.5
14
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
IDD_IO
3.7
5.7
mA
IISOIN
3.2
4.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.7
5.7
mA
IISOIN
3.2
4.5
mA
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
MIN
UNIT
ISOW7742 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7743 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7744 Channel Supply Current
Supply current - Disable
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
19
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 3.3 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
Channel Supply current DC signal
TEST CONDITIONS
20
TYP
MAX
UNIT
IDD_IO
3.7
5.7
mA
IISOIN
3.2
4.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
4
6.1
mA
IISOIN
7.6
10.1
mA
IDD_IO
3.8
6.1
mA
IISOIN
5.5
7.3
mA
IDD_IO
5.5
7.8
mA
IISOIN
5.5
7.3
mA
IDD_IO
21
29
mA
IISOIN
6.3
8.3
mA
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
(1)
MIN
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
VCCI = VIO or VISOIN
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.15 Electrical Characteristics Channel Isolator - VIO, VISOIN = 2.5-V
VIO, VISOIN = 2.5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Channel Isolation
VITH
Input pin rising threshold
VITL
Input pin falling threshold
0.3 x VSI
V
VI(HYS)
Input pin threshold hysteresis
(INx)
0.1 x VSI
V
IIL
Low level input current
-25
µA
IIH
0.7 x VSI
VIL = 0 at INx
(1)
High level input current
VIH = VSI
VOH
High level output voltage
IO = –1 mA, see Switching Characteristics
Test Circuit and Voltage Waveforms
VOL
Low level output voltage
IO = 1 mA, see Switching Characteristics Test
Circuit and Voltage Waveforms
CMTI
Common mode transient
immunity
VI = VSI or 0 V, VCM = 1000 V; see CommonMode Transient Immunity Test Circuit
(1)
at INx
V
25
µA
VSO (1) –
0.1
V
0.1
85
V
100
kV/us
VSI = input side supply; VSO = output side supply
7.16 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 2.5-V
VIO, VISOIN = 2.5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
ISOW7740 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.4
3.8
mA
IISOIN
4.5
6.9
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
2.4
3.8
mA
IISOIN
4.5
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
2.4
3.8
mA
IISOIN
4.5
6.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
6.8
9
mA
IISOIN
4.7
7.2
mA
IDD_IO
4.6
6.4
mA
IISOIN
4.7
7
mA
IDD_IO
4.7
6.4
mA
IISOIN
5.7
8.1
mA
IDD_IO
5.3
7.2
mA
IISOIN
18
24
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.7
4.3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
2.7
4.3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.7
4.3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
6.1
8.3
mA
IISOIN
5.4
7.9
mA
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7741 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
21
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 2.5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
TYP
MAX
IDD_IO
4.4
6.3
mA
IISOIN
4.9
7.1
mA
IDD_IO
4.7
8.3
mA
IISOIN
5.6
7.9
mA
IDD_IO
8.2
11.2
mA
IISOIN
14.6
18.8
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.8
5.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.8
5.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
3.1
4.6
mA
IISOIN
3.8
5.4
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
5.3
7.5
mA
IISOIN
6.1
8.4
mA
IDD_IO
4.2
6.3
mA
IISOIN
5.1
7.2
mA
IDD_IO
4.7
6.8
mA
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
MIN
UNIT
ISOW7742 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
IISOIN
5.6
7.7
mA
IDD_IO
10.9
14.5
mA
IISOIN
11.7
15.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.5
4.9
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.5
4.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.4
5.1
mA
IISOIN
3.5
4.9
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
4.6
6.7
mA
IISOIN
6.8
9.3
mA
IDD_IO
4
6.2
mA
IISOIN
5.3
7.2
mA
IDD_IO
4.8
7
mA
IISOIN
5.6
7.5
mA
IDD_IO
13.8
17
mA
IISOIN
8.3
13
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
IDD_IO
3.7
5.9
mA
IISOIN
3.2
4.4
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.7
5.7
mA
IISOIN
3.2
4.4
mA
100 Mbps
ISOW7743 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7744 Channel Supply Current
Supply current - Disable
22
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 2.5 V ±10% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
Channel Supply current DC signal
TEST CONDITIONS
TYP
MAX
UNIT
IDD_IO
3.7
5.7
mA
IISOIN
3.2
4.4
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.9
6.2
mA
IISOIN
7.5
10
mA
IDD_IO
3.8
6.1
mA
IISOIN
5.5
7.3
mA
IDD_IO
4.8
7.2
mA
IISOIN
5.5
7.3
mA
IDD_IO
16.5
22
mA
IISOIN
6
8.1
mA
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
(1)
MIN
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
VCCI = VIO or VISOIN
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
23
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.17 Electrical Characteristics Channel Isolator - VIO, VISOIN = 1.8-V
VIO, VISOIN = 1.8 V ±5% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Channel Isolation
VITH
Input pin rising threshold
VITL
Input pin falling threshold
0.3 x VSI
V
VI(HYS)
Input pin threshold hysteresis
(INx)
0.1 x VSI
V
IIL
Low level input current
-25
µA
IIH
0.7 x VSI
VIL = 0 at INx
(1)
High level input current
VIH = VSI
VOH
High level output voltage
IO = –1 mA, see Switching Characteristics
Test Circuit and Voltage Waveforms
VOL
Low level output voltage
IO = 1 mA, see Switching Characteristics Test
Circuit and Voltage Waveforms
CMTI
Common mode transient
immunity
VI = VSI or 0 V, VCM = 1000 V; see CommonMode Transient Immunity Test Circuit
(1)
at INx
V
25
µA
VSO (1) –
0.1
V
0.1
85
V
100
kV/us
VSI = input side supply; VSO = output side supply
7.18 Supply Current Characteristics Channel Isolator - VIO, VISOIN = 1.8-V
VIO, VISOIN = 1.8 V ±5% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
SUPPLY
CURRENT
MIN
TYP
MAX
UNIT
ISOW7740 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
1.9
3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
1.9
3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7740);
VI = 0 V (ISOW7740 with F suffix)
IDD_IO
1.9
3
mA
IISOIN
4.2
6.3
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7740);
VI = VCCI (ISOW7740 with F suffix)
IDD_IO
6.1
8.7
mA
IISOIN
4.4
6.7
mA
IDD_IO
4.0
6.4
mA
IISOIN
4.7
7
mA
IDD_IO
4.0
6.4
mA
IISOIN
5.4
7.7
mA
IDD_IO
4.6
9.5
mA
IISOIN
14.6
19
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.4
3.6
mA
IISOIN
3.8
5.6
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
2.4
3.6
mA
IISOIN
3.8
5.6
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7741);
VI = 0 V (ISOW7741 with F suffix)
IDD_IO
2.4
3.6
mA
IISOIN
3.8
5.6
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7741);
VI = VCCI (ISOW7741 with F suffix)
IDD_IO
5.5
7.8
mA
IISOIN
4.9
7.3
mA
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7741 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
24
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 1.8 V ±5% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
TEST CONDITIONS
TYP
MAX
IDD_IO
4
5.7
mA
IISOIN
4.4
6.5
mA
IDD_IO
4.2
6
mA
IISOIN
5.2
7.3
mA
IDD_IO
6.9
9.6
mA
IISOIN
12
15.8
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
2.8
4.3
mA
IISOIN
3.4
5.1
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
2.8
4.3
mA
IISOIN
3.4
5.1
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7742);
VI = 0 V (ISOW7742 with F suffix)
IDD_IO
2.8
4.3
mA
IISOIN
3.4
5.1
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7742);
VI = VCCI (ISOW7742 with F suffix)
IDD_IO
5
7.4
mA
IISOIN
5.6
8.1
mA
IDD_IO
4.2
6.3
mA
IISOIN
4.5
7.2
mA
IDD_IO
4.3
6.6
mA
IISOIN
5.0
7.5
mA
IDD_IO
9.1
12.5
mA
IISOIN
9.7
13.3
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.2
5
mA
IISOIN
3
4.5
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
3.2
5
mA
IISOIN
3
4.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7743);
VI = 0 V (ISOW7743 with F suffix)
IDD_IO
3.2
5
mA
IISOIN
3
4.5
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7743);
VI = VCCI (ISOW7743 with F suffix)
IDD_IO
4.4
6.6
mA
IISOIN
6.2
8.9
mA
IDD_IO
4
6.2
mA
IISOIN
4.6
7.2
mA
IDD_IO
4.6
6.7
mA
IISOIN
4.9
7.4
mA
IDD_IO
11.4
15
mA
IISOIN
7.8
9.8
mA
EN_IO1 = EN_IO2 = 0 V; VI = VCCI (1) (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
IDD_IO
3.6
5.7
mA
IISOIN
2.6
3.8
mA
EN_IO1 = EN_IO2 = 0 V; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.6
5.7
mA
IISOIN
2.6
3.8
mA
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
MIN
UNIT
ISOW7742 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7743 Channel Supply Current
Supply current - Disable
Channel Supply current DC signal
1 Mbps
Channel Supply current AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
ISOW7744 Channel Supply Current
Supply current - Disable
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
25
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VIO, VISOIN = 1.8 V ±5% GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions, unless otherwise
specified)
PARAMETER
Channel Supply current DC signal
TEST CONDITIONS
26
TYP
MAX
UNIT
IDD_IO
3.6
5.7
mA
IISOIN
2.6
3.8
mA
EN_IO1 = EN_IO2 = VCCI; VI = 0 V (ISOW7744);
VI = VCCI (ISOW7744 with F suffix)
IDD_IO
3.8
6.1
mA
IISOIN
6.7
9.6
mA
IDD_IO
3.8
6.1
mA
IISOIN
4.7
7.3
mA
IDD_IO
4.5
7
mA
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
(1)
MIN
EN_IO1 = EN_IO2 = VCCI; VI = VCCI (ISOW7744);
VI = 0 V (ISOW7744 with F suffix)
1 Mbps
Channel Supply current AC signal
SUPPLY
CURRENT
IISOIN
4.7
7.3
mA
IDD_IO
13.8
16.9
mA
IISOIN
5.2
7.7
mA
VCCI = VIO or VISOIN
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.19 Switching Characteristics - 5-V Supply
VISOIN = 5 V ±10%, VIO = 5 V ±10%, GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions unless
otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion(1) |tPHL – tPLH|
TEST CONDITIONS
See Switching Characteristics Test
Circuit and Voltage Waveforms
ENIO_tPLH,
ENIO_tPHL
ENIO propagation delay time (opposite side)
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tsk(o)
Channel-to-channel output skew time(2)
Same-direction channels
tsk(pp)
Part-to-part skew time(3)
tr
Output signal rise time
tf
Output signal fall time
MIN
TYP
MAX
UNIT
7.6
10.7
15.7
ns
0.9
5
ns
210
473.8
ns
4
ns
5.5
ns
2.5
3.6
ns
2.4
3.5
ns
tPHZ
Channel disable propagation delay, high-to-high impedance
output
217
286
ns
tPLZ
Channel disable propagation delay, low-to-high impedance
output
217
286
ns
237
333
ns
237
333
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x
237
333
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x with F suffix
237
333
ns
0.3
μs
tPZH
tPZL
Channel enable propagation delay, high impedance-to-high
output for ISOW774x
Channel enable propagation delay, high impedance-to-high
output for ISOW774x with F suffix
See Switching Characteristics Test
Circuit and Voltage Waveforms
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tDO
Default output delay time from input power loss
Measured from the time VIO or VISOIN
goes below 1.6 V at 10 mV/ns.
See Default Output Delay Time Test
Circuit and Voltage Waveforms
0.1
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
0.7
(1)
(2)
(3)
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
27
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.20 Switching Characteristics - 3.3-V Supply
VISOIN = 3.3 V ±10%, VIO = 3.3 V ±10%, GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions unless
otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion(1) |tPHL – tPLH|
TEST CONDITIONS
MIN
6
See Switching Characteristics Test
Circuit and Voltage Waveforms
ENIO_tPLH,
ENIO_tPHL
ENIO propagation delay time (opposite side)
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tsk(o)
Channel-to-channel output skew time(2)
Same-direction channels
tsk(pp)
Part-to-part skew time(3)
tr
Output signal rise time
tf
Output signal fall time
TYP
MAX
UNIT
11
16.2
ns
0.6
4.7
ns
220
474
ns
4.1
ns
4.5
ns
1.8
2.7
ns
1.6
2.4
ns
tPHZ
Channel disable propagation delay, high-to-high impedance
output
230
300.4
ns
tPLZ
Channel disable propagation delay, low-to-high impedance
output
230
299.6
ns
226
318.9
ns
226
319.1
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x
225
317.9
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x with F suffix
225
317.6
ns
0.1
0.3
μs
tPZH
tPZL
Channel enable propagation delay, high impedance-to-high
output for ISOW774x
Channel enable propagation delay, high impedance-to-high
output for ISOW774x with F suffix
See Switching Characteristics Test
Circuit and Voltage Waveforms
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tDO
Default output delay time from input power loss
Measured from the time VIO or VISOIN
goes below 1.6 V at 10 mV/ns.
See Default Output Delay Time Test
Circuit and Voltage Waveforms
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
(1)
(2)
(3)
28
0.65
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.21 Switching Characteristics - 2.5-V Supply
VISOIN = 2.5 V ±10%, VIO = 2.5 V ±10%, GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions unless
otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion(1) |tPHL – tPLH|
TEST CONDITIONS
See Switching Characteristics Test
Circuit and Voltage Waveforms
ENIO_tPLH,
ENIO_tPHL
ENIO propagation delay time (opposite side)
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tsk(o)
Channel-to-channel output skew time(2)
Same-direction channels
tsk(pp)
Part-to-part skew time(3)
tr
Output signal rise time
tf
Output signal fall time
MIN
7.5
TYP
MAX
UNIT
12
18
ns
0.36
5.1
ns
225
478
ns
4.1
ns
6
ns
2
3.26
ns
1.8
3.2
ns
tPHZ
Channel disable propagation delay, high-to-high impedance
output
237
326
ns
tPLZ
Channel disable propagation delay, low-to-high impedance
output
236
325
ns
228
360
ns
228
360
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x
227
350
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x with F suffix
227
350
ns
0.3
μs
tPZH
tPZL
Channel enable propagation delay, high impedance-to-high
output for ISOW774x
Channel enable propagation delay, high impedance-to-high
output for ISOW774x with F suffix
See Switching Characteristics Test
Circuit and Voltage Waveforms
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tDO
Default output delay time from input power loss
Measured from the time VIO or VISOIN
goes below 1.6 V at 10 mV/ns.
See Default Output Delay Time Test
Circuit and Voltage Waveforms
0.1
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
0.7
(1)
(2)
(3)
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
29
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.22 Switching Characteristics - 1.8-V Supply
VISOIN = 1.8 V ±5%, VIO = 1.8 V ±5%, GND1 = GNDIO, GND2 = GISOIN (over recommended operating conditions unless
otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion(1) |tPHL – tPLH|
TEST CONDITIONS
See Switching Characteristics Test
Circuit and Voltage Waveforms
ENIO_tPLH,
ENIO_tPHL
ENIO propagation delay time (opposite side)
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tsk(o)
Channel-to-channel output skew time(2)
Same-direction channels
tsk(pp)
Part-to-part skew time(3)
tr
Output signal rise time
tf
Output signal fall time
MIN
TYP
MAX
UNIT
7.5
15
21.5
ns
0
5.8
ns
243
475
ns
4.1
ns
8.6
ns
1.9
3
ns
1.8
3
ns
tPHZ
Channel disable propagation delay, high-to-high impedance
output
260
410
ns
tPLZ
Channel disable propagation delay, low-to-high impedance
output
260
406
ns
240
444
ns
240
444
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x
237
439
ns
Channel enable propagation delay, high impedance-to-low
output for ISOW774x with F suffix
237
439
ns
0.3
μs
tPZH
tPZL
Channel enable propagation delay, high impedance-to-high
output for ISOW774x
Channel enable propagation delay, high impedance-to-high
output for ISOW774x with F suffix
See Switching Characteristics Test
Circuit and Voltage Waveforms
See Enable/Disable Propagation Delay
Time Test Circuit and Waveform
tDO
Default output delay time from input power loss
Measured from the time VIO or VISOIN
goes below 1.6 V at 10 mV/ns.
See Default Output Delay Time Test
Circuit and Voltage Waveforms
0.1
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
0.7
(1)
(2)
(3)
30
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.23 Insulation Characteristics Curves
550
VDD = VIO = VISOIN = 3.6 V
VDD = VIO = VISOIN = 5.5 V
Safety Limiting Current (mA)
500
450
400
350
300
250
200
150
100
50
0
0
20
40
60
80
100
120
Ambient Temperature (C)
140
160
Figure 7-1. Thermal Derating Curve for Safety
Limiting Current for DFM-20 Package
Copyright © 2022 Texas Instruments Incorporated
Figure 7-2. Thermal Derating Curve for Safety
Limiting Power for DFM-20 Package
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
31
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
7.24 Typical Characteristics
3.4
5.1
VDD = 5 V
VDD = 3.3 V
5.08
3.36
5.06
3.34
5.04
Output Voltage (V)
Output Voltage (V)
3.38
3.32
3.3
3.28
3.26
5
4.98
4.96
3.24
4.94
3.22
4.92
3.2
4.9
0
20
40
60
80
100
Load Current (mA)
VSEL = GND2
TA = 25°C
120
140
0
VISOOUT = 3.3 V
Figure 7-3. Isolated Supply Voltage (VISOOUT) vs
Load Current (IISOOUT)
48
240
45
210
42
180
39
120
90
VDD = 5 V, VISOOUT = 5 V
VDD = 3.3 V, VISOOUT = 3.3 V
VDD = 5 V, VISOOUT = 3.3 V
60
30
20
40
60
80
100
Load Current (mA)
120
VISOOUT = 5 V
30
VDD = 5 V, VISOOUT = 5 V
VDD = 3.3 V, VISOOUT = 3.3 V
VDD = 5 V, VISOOUT = 3.3 V
21
0
20
40
60
80
100
Load Current (mA)
120
140
600
500
400
300
VDD = 5 V, VISOOUT = 5 V
VDD = 3.3 V, VISOOUT = 3.3 V
VDD = 5 V, VISOOUT = 3.3 V
200
100
0
40
60
80
100
Output Load Current (mA)
120
140
Figure 7-6. Efficiency vs Load Current (IVISOOUT)
Output Power Supply Voltage, VISOOUT (V)
700
Power Dissipation (mW)
TA = 25°C
TA = 25°C
800
3.35
3.34
3.33
3.32
3.31
3.3
3.29
3.28
3.27
3.26
3.25
-40
-25
-10
5
VSEL = GND2
TA = 25°C
Figure 7-7. Power Dissipation vs Load Current
(IISOOUT)
32
90 100 110 120
33
24
140
Figure 7-5. Supply Current (IDD) vs Load Current
(IISOOUT)
20
40 50 60 70 80
Load Current (mA)
36
TA = 25°C
0
30
27
0
0
20
Figure 7-4. Isolated Supply Voltage (VISOOUT) vs
Load Current (IISOOUT)
270
150
10
VSEL = VISOOUT
Efficiency (%)
Input Supply Current (mA)
5.02
Submit Document Feedback
20
35
50
65
Temperature (C)
VDD = 5 V
80
95
110 125
No VISOOUT Load
Figure 7-8. 3.3-V Isolated Supply Voltage (VISOOUT)
vs Free-Air Temperature
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
5.05
340
5.04
320
Short-Circuit Supply Current (mA)
Output Power Supply Voltage, VISOOUT (V)
www.ti.com
5.03
5.02
5.01
5
4.99
4.98
4.97
4.96
4.95
-40
-25
-10
5
20
35
50
65
Temperature (C)
VSEL = VISOOUT
80
VDD = 5 V
95
300
280
260
240
220
200
180
160
110 125
3
No VISOOUT Load
Figure 7-9. 5-V Isolated Supply Voltage (VISOOUT) vs
Free-Air Temperature
11.5
18
15
12
9
6
5.25
5.5
VISOOUT = GND2 TA = 25°C = GND1
9.5
8.5
7.5
6.5
5.5
4.5
3
3.5
0
0
10
20
30
40
50
60
70
Data Rate (Mbps)
CL = 15 pF
80
90
0
100
10
20
30
40
50
60
70
Data Rate (Mbps)
CL = 0 pF
TA = 25°C
Figure 7-11. ISOW7740 Channel Supply Currents
vs Data Rate For CL = 15 pF
80
90
100
TA = 25°C
Figure 7-12. ISOW7740 Channel Supply Currents
vs Data Rate For CL = 0 pF
24
20
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
20
18
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
18
16
Supply Current (mA)
22
Supply Current (mA)
5
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
10.5
Supply Current (mA)
Supply Current (mA)
21
3.75
4
4.25 4.5 4.75
Input Supply Voltage, VDD (mA)
Figure 7-10. Short-Circuit Supply Current (ICC) vs
Supply Voltage (VCC)
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
24
3.5
VSEL = VISOOUT
30
27
3.25
16
14
12
10
8
14
12
10
8
6
6
4
4
2
2
0
10
20
30
CL = 15 pF
40
50
60
Data Rate (Mbps)
70
80
90
100
TA = 25°C
Figure 7-13. ISOW7741 Channel Supply Currents
vs Data Rate For CL = 15 pF
Copyright © 2022 Texas Instruments Incorporated
0
10
20
30
CL = 0 pF
40
50
60
Data Rate (Mbps)
70
80
90
100
TA = 25°C
Figure 7-14. ISOW7741 Channel Supply Currents
vs Data Rate For CL = 0 pF
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
33
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
18
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
Supply Current (mA)
16
14
12
10
8
6
4
2
0
10
20
30
40
50
60
70
Data Rate (Mbps)
CL = 15 pF
TA = 25°C
80
90
100
CL = 0 pF
Figure 7-15. ISOW7742 Channel Supply Currents
vs Data Rate For CL = 15 pF
TA = 25°C
Figure 7-16. ISOW7742 Channel Supply Currents
vs Data Rate For CL = 0 pF
24
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
22
Supply Current (mA)
20
18
16
14
12
10
8
6
4
2
0
10
20
30
40
50
60
70
Data Rate (Mbps)
CL = 15 pF
TA = 25°C
80
90
100
CL = 0 pF
Figure 7-17. ISOW7743 Channel Supply Currents
vs Data Rate For CL = 15 pF
Figure 7-18. ISOW7743 Channel Supply Currents
vs Data Rate For CL = 0 pF
24
12.5
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
Supply Current (mA)
20
18
IIO, VIO = 5 V
IISOIN, VISOIN = 5 V
IIO, VIO = 3.3 V
IISOIN, VISOIN = 3.3 V
11.5
10.5
Supply Current (mA)
22
16
14
12
10
8
9.5
8.5
7.5
6.5
5.5
6
4.5
4
3.5
2
0
10
20
30
40
50
60
70
Data Rate (Mbps)
CL = 15 pF
TA = 25°C
80
90
100
Figure 7-19. ISOW7744 Channel Supply Currents
vs Data Rate For CL = 15 pF
34
TA = 25°C
Submit Document Feedback
0
10
20
30
CL = 0 pF
40
50
60
70
Data Rate (Mbps)
80
90
100
TA = 25°C
Figure 7-20. ISOW7744 Channel Supply Currents
vs Data Rate For CL = 0 pF
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
3
17
2.75
16
Propogation Delay Time (ns)
Power Supply UVLO Threshold (V)
www.ti.com
2.5
VIO UVLO+
VIO UVLOVISOIN UVLO+
VISOIN UVLOVDD UVLO+
VDD UVLO-
2.25
2
1.75
1.5
15
14
VIO
VIO
VIO
VIO
VIO
VIO
=
=
=
=
=
=
5 V, VISOIN = 5 V
5 V, VISOIN = 5 V
5 V, VISOIN = 3.3 V
5 V, VISOIN = 3.3 V
3.3 V, VISOIN = 3.3 V
3.3 V, VISOIN = 3.3 V
13
12
11
10
1.25
-40
-25
-10
5
20
35
50
65
Temperature (C)
80
95
9
-40
110 125
-25
-10
5
20
35
50
65
Temperature (C)
80
95
110 125
Figure 7-22. Propagation Delay Time vs Free-Air
Temperature
Figure 7-21. Power-Supply Undervoltage
Threshold vs Free Air Temperature
5
0.8
Low-Level Output Voltage (V)
High-Level Output Voltage (V)
tPHL,
tPLH,
tPHL,
tPLH,
tPHL,
tPLH,
4.5
VSO = 3.3 V
VSO = 5 V
4
3.5
3
2.5
-15
0.6
0.4
0.2
VSO = 3.3 V
VSO = 5 V
0
-12
-9
-6
-3
High-Level Output Current (mA)
0
0
3
6
9
12
Low-Level Output Current (mA)
15
TA = 25°C
TA = 25°C
Figure 7-23. High-Level Output Voltage vs HighLevel Output Current
VDD = 5 V VISOOUT = 3.3
V
TA = 25°C
Figure 7-25. 10-mA to 110-mA Load Transient
Response
Copyright © 2022 Texas Instruments Incorporated
Figure 7-24. Low-Level Output Voltage vs LowLevel Output Current
VDD = 5 V VISOOUT = 3.3
V
10 uF
Capacitor on
VISOOUT
Figure 7-26. Soft Start at 10-mA Load For VISOOUT =
3.3 V
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
35
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VDD = 5 V VISOOUT = 3.3
V
10 uF
Capacitor on
VISOOUT
VDD = 5 V VISOOUT = 3.3
V
10 uF
Capacitor on
VISOOUT
Figure 7-27. Soft Start at 50-mA Load For VISOOUT = Figure 7-28. Soft Start at 110-mA Load For VISOOUT
= 3.3 V
3.3 V
VDD = 5 V VISOOUT = 5 V
10 uF
Capacitor on
VISOOUT
VDD = 5 V VISOOUT = 5 V
10 uF
Capacitor on
VISOOUT
Figure 7-29. Soft Start at 10-mA Load For VISOOUT = Figure 7-30. Soft Start at 50-mA Load For VISOOUT =
5V
5V
VDD = 5 V VISOOUT = 5 V
10 uF
Capacitor on
VISOOUT
Figure 7-31. Soft Start at 110-mA Load For VISOOUT
=5V
36
Submit Document Feedback
VDD = 3.3 V VISOOUT = 3.3
V
10 uF
Capacitor on
VISOOUT
Figure 7-32. VISOOUT Ripple Voltage at 3.3 V with 10
uF Capacitor and 60 mA load
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
VDD = 5 V VISOOUT = 5 V
10 uF
Capacitor on
VISOOUT
Figure 7-33. VISOOUT Ripple Voltage at 5 V with 10
uF Capacitor and 110 mA load
VDD = 5 V VISOOUT = 5 V
100 uF
Capacitor on
VISOOUT
Figure 7-35. VISOOUT Ripple Voltage at 5 V with 100
uF Capacitor and 110 mA load
Copyright © 2022 Texas Instruments Incorporated
VDD = 3.3 V VISOOUT = 3.3
V
100 uF
Capacitor on
VISOOUT
Figure 7-34. VISOOUT Ripple Voltage at 3.3 V with
100 uF Capacitor and 60 mA load
TA = 25°C
Figure 7-36. VISOOUT Ripple Voltage vs Load
Capacitor
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
37
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
8 Parameter Measurement Information
In the below images, VCCI and VCCO refers to the power supplies VIO and VISOIN, respectively.
Isolation Barrier
IN
Input Generator
(See Note A)
VI
VCCI
VI
OUT
50%
50%
0V
tPLH
VO
50
tPHL
CL
See Note B
VOH
90%
50%
VO
50%
10%
VOL
tf
tr
Copyright © 2016, Texas Instruments Incorporated
A.
B.
CL = 15 pF and The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3 ns,
tf ≤ 3ns, ZO = 50 Ω. At the input, 50 Ω resistor is required to terminate Input Generator signal. It is not needed in actual application.
B. CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 8-1. Switching Characteristics Test Circuit and Voltage Waveforms
VCC1
Isolation Barrier
0 V or 3 V
IN
0V
OUT
tPZH
VO
VOH
50%
VO
EN
RL = 1 k
Input
Generator
(See Note A)
VCC / 2
VCC / 2
VI
±1%
0.5 V
0V
tPHZ
CL
See Note B
tPZL
tPLZ
VOH
VI
50
VO
0.5 V
50%
VOL
A.
B.
A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3 ns, tf ≤ 3ns, ZO
= 50 Ω. At the input, 50 Ω resistor is required to terminate Input Generator signal. It is not needed in actual application.
B. CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 8-2. Enable/Disable Propagation Delay Time Test Circuit and Waveform
VCCI
See Note B
IN = 0 V (Devices without suffix F)
IN = VCC (Devices with suffix F)
IN
Isolation Barrier
VCCI
VI
OUT
1.4 V
0V
VO
CL
See Note A
tDO
VO
default high
VOH
50%
VOL
default low
Note
A. CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
38
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
Note
B. Power Supply Ramp Rate = 10 mV/ns.
Figure 8-3. Default Output Delay Time Test Circuit and Voltage Waveforms
5V
Connected to Visoout on PCB
VISOIN
VIO
10uF
1uF
0.01uF
0.01uF
1uF
10uF
VIO
GND1
OUT
IN
5V
GND1
VDD
CL
10uF
1uF
0.01uF
GND2
GND1
+
–
VCM
Note
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Note
Pass-fail criteria: Outputs must remain stable.
Figure 8-4. Common-Mode Transient Immunity Test Circuit
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
39
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
9 Detailed Description
9.1 Overview
The ISOW774x family of devices have low-noise, low-emissions isolated DC-DC converter, and four high- speed
isolated data channels. Section 9.2 shows the functional block diagram of the ISOW774x device.
9.1.1 Power Isolation
The integrated isolated DC-DC converter uses advanced circuit and on-chip layout techniques to reduce
radiated emissions and achieve upto 46% typical efficiency. The integrated transformer uses thin film polymer
as the insulation barrier. Output voltage of power converter can be controlled to 3.3 V or 5 V using VSEL
pin. The DC-DC converter can be switched off using the EN/FLT pin to save power. The output voltage,
VISOOUT , is monitored and feedback information is conveyed to the primary side through a dedicated isolation
channel. VISOOUT needs to be connected to VISOIN to ensure the feedback channel is properly powered to
regulate the DC-DC converter. This can be achieved by connecting the pins directly or through an LDO that
remains powered up at all times. A ferrite bead is recommended between Visoout and Visoin to further reduce
emissions. See the Section 10.2 section. The duty cycle of the primary switching stage is adjusted accordingly.
The fast feedback control loop of the power converter ensures low overshoots and undershoots during load
transients. Undervoltage lockout (UVLO) with hysteresis is integrated on the VIO, VDD and VISOIN supplies
which ensures robust fails-safe system performance under noisy conditions. An integrated soft-start mechanism
ensures controlled inrush current and avoids any overshoot on the output during power up.
9.1.2 Signal Isolation
The integrated signal isolation channels employ an ON-OFF keying (OOK) modulation scheme to transmit the
digital data across a silicon-dioxide based isolation barrier. The transmitter sends a high frequency carrier
across the barrier to represent one state and sends no signal to represent the other state. The receiver
demodulates the signal after signal conditioning and produces the output through a buffer stage. The signalisolation channels incorporate advanced circuit techniques to maximize the CMTI performance and minimize the
radiated emissions from the high frequency carrier and IO buffer switching. Figure 9-1 shows a functional block
diagram of a typical signal isolation channel. In order to keep any noise coupling from power converter away
from signal path, power supplies on side 1 for power converter (VDD) and signal path(VIO) are kept separate.
Similarly on side 2, power converter output (VISOOUT) needs to be connected to VISOIN externally on PCB.
Emissions can be further improved by placing a ferrite bead between VISOOUT and VISOIN as well as between the
GND2 pins. For more details, refer to the Layout Guidelines section.
40
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
9.2 Functional Block Diagram
VISOIN
VIO
Isolation Barrier
I/O Channels
Data Channels
(4)
Data Channels
(4)
FB Channel (Rx)
FB Channel (Tx)
VISOOUT and
VISOIN needs to
be directly
connected or
through an
LDO on board
that is always
powered.
I/O Channels
FB Controller
Vref
Thermal
Shutdown,
UVLO, Soft-start
UVLO, Soft-start
Transformer
Driver
Power
Controller
Rectifier
VISOOUT
VDD
Transformer
Figure 9-1. Block Diagram
Receiver
Transmitter
TX IN
OOK
Modulation
TX Signal
Conditioning
Oscillator
SiO2 based
Capacitive
Isolation
Barrier
RX Signal
Conditioning
Envelope
Detection
RX OUT
Emissions
Reduction
Techniques
Figure 9-2. Conceptual Block Diagram of a Capacitive Data Channel
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
41
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
Figure 9-3 shows a conceptual detail of how the OOK scheme works.
TX IN
Carrier signal through
isolation barrier
RX OUT
Figure 9-3. On-Off Keying (OOK) Based Modulation Scheme
9.3 Feature Description
Table 9-1 shows an overview of the device features.
Table 9-1. Device Features
PART NUMBER1
ISOW7740
ISOW7740F
ISOW7741
ISOW7741F
ISOW7742
ISOW7742F
ISOW7743
ISOW7743F
ISOW7744
ISOW7744F
CHANNEL DIRECTION
MAXIMUM DATA RATE
RATED ISOLATION2
High
4 forward, 0 reverse
Low
High
3 forward, 1 reverse
2 forward, 2 reverse
DEFAULT OUTPUT
STATE
Low
100 Mbps
1 forward, 3 reverse
0 forward, 4 reverse
High
Low
5 kVRMS / 7071 VPK
High
Low
High
Low
1. The F suffix is part of the orderable part number. See the Section 14 section for the full orderable part
number.
2. For detailed isolation ratings, see the Section 7.7 table.
9.3.1 Electromagnetic Compatibility (EMC) Considerations
The ISOW774x devices use emissions reduction schemes for the internal oscillator and advanced internal layout
scheme to minimize radiated emissions at the system level.
Many applications in harsh industrial environment are sensitive to disturbances such as electrostatic discharge
(ESD), electrical fast transient (EFT), surge and electromagnetic emissions. These electromagnetic disturbances
are regulated by international standards such as IEC 61000-4-x and CISPR 32. Although system-level
performance and reliability depends, to a large extent, on the application board design and layout, the
ISOW774x devices incorporate many chip-level design improvements for overall system robustness. Some of
these improvements include:
• Robust ESD protection cells for input and output signal pins and inter-chip bond pads.
• Low-resistance connectivity of ESD cells to supply and ground pins.
• Enhanced performance of high voltage isolation capacitor for better tolerance of ESD, EFT and surge events.
• Bigger on-chip decoupling capacitors to bypass undesirable high energy signals through a low impedance
path.
42
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
•
•
•
•
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
PMOS and NMOS devices isolated from each other by using guard rings to avoid triggering of parasitic
SCRs.
Reduced common mode currents across the isolation barrier by ensuring purely differential internal operation.
Power path and signal path separated to minimize internal high frequency coupling and allowing for an
external filtering knob using ferrite beads available to further reduce emissions
Reduced power converter switching frequency to 25 Mhz to reduce strength of high frequency components in
emissions spectrum
9.3.2 Power-Up and Power-Down Behavior
The ISOW774x device has built-in UVLO on the VIO, VDD, and VISOIN supplies with positive-going and negativegoing thresholds and hysteresis. Both the power converter supply (VDD) and logic supply (VIO) need to be
present for the device to work. If either of them is below its UVLO, both the signal path and the power converter
are disabled.
When the VDD voltage crosses the positive-going UVLO threshold during power-up, the DC-DC converter
initializes and the power converter duty cycle is increased in a controlled manner. This soft-start scheme limits
primary peak currents drawn from the VDD supply and charges the VISOOUT output in a controlled manner,
avoiding overshoots. Outputs of the isolated data channels are in an indeterminate state until the VIO or VDD
voltage crosses the positive-going UVLO threshold. When the UVLO positive-going threshold is crossed on the
secondary side VISOOUT pin, the feedback data channel starts providing feedback to the primary controller. The
regulation loop takes over and the isolated data channels go to the normal state defined by the respective input
channels or their default states. Design should consider a sufficient time margin (typically 10 ms with 10-µF load
capacitance) to allow this power up sequence before valid data channels are accounted for system functionality.
When either VIO or VDD power is lost, the primary side DC-DC controller turns off when the UVLO lower
threshold is reached. The VISOOUT capacitor then discharges depending on the external load. The isolated data
outputs on the VISOIN side are returned to the default state for the brief time that the VISOIN voltage takes to
discharge to zero.
9.3.3 Protection Features
The ISOW774x devices have multiple protection features to create a robust system level solution.
•
The Enable DC-DC / FAULT protection feature (EN/FLT) can be used as either an input pin, to enable or
disable the integrated DC-DC power converter, or as an output pin, which works as an alert signal if the
power converter is not operating properly. In the /FAULT use case, an alert is reported if VDD > 7 V, VDD < 2.5
V, or if the junction temperature >170°C. When a fault is detected, this pin will go low, disabling the DC-DC
converter to prevent any damage.
MCU OUTPUT
5 kΩ
EN/FLT
Powers Down Isolator Channels
and DC-DC Converter.
IQ < 1 mA Typical
MCU INPUT
Fault Reported If
VDD < 2.5 V
VDD > 7 V
Junction Temp > 170° C
Figure 9-4. EN/FLT Fault Pin Diagram
•
•
•
An over-voltage clamp feature is present on VISOOUT which will clamp the voltage at 6 V, when VSEL =
VISOOUT, or 4 V, when VSEL = GND2, if there is an increase in voltage seen on VISOOUT. It is recommended
that the VISOOUT stays lower than the over-clamp voltage for device reliability.
Over-voltage lock out on VDD will occur when a voltage higher than 7 V is seen. The device will go into a low
power state and the EN/FLT pin will go low.
The device is protected against output overload and short circuit. Output voltage starts dropping when the
power converter is not able to deliver the current demanded during overload conditions. For a VISOOUT
short-circuit to ground, the duty cycle of the converter is limited to help protect against any damage.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
43
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
•
•
•
44
The device is protected against output overload and short circuit. Output voltage starts dropping when the
power converter is not able to deliver the current demanded during overload conditions. For a VISOOUT
short-circuit to ground, the duty cycle of the converter is limited to help protect against any damage.
The device is protected against output overload and short circuit. Output voltage starts dropping when the
power converter is not able to deliver the current demanded during overload conditions. For a VISOOUT
short-circuit to ground, the duty cycle of the converter is limited to help protect against any damage.
Thermal protection is also integrated to help prevent the device from getting damaged during overload
and short-circuit conditions on the isolated output. Under these conditions, the device temperature starts to
increase. When the temperature goes above 165°C, thermal shutdown activates and the primary controller
turns off which removes the energy supplied to the VISOOUT load, which causes the device to cool off.
When the junction temperature goes below 150°C, the device starts to function normally. If an overload or
output short-circuit condition prevails, this protection cycle is repeated. Care should be taken in the design to
prevent the device junction temperatures from reaching such high values.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
9.4 Device Functional Modes
Table 9-2 lists the supply configurations for these devices.
Table 9-2. Supply Configuration Function Table
VDD
(1)
< VDD(UVLO+)
(3)
VSEL
VISOOUT(3)
>VIO(UVLO+)
X
OFF
OFF
>VDD(UVLO+)
1.7 V, VISOIN > 1.7 V); PD = Powered down
(VIO < 1 V, VISOIN < 1 V); X = Irrelevant; H = High level; L = Low level.
In the default condition, the output is high for the ISOW774x device and low with the F suffix.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
45
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
9.4.1 Device I/O Schematics
INx (Devices without F suffix)
VCC I
VCC I
VCC I
INx (Devices with F suffix)
VCC I
VCC I
VCC I
VCC I
1.5 M
INx
INx
1.5 M
VSEL
OUTx
VCC O
VISOOU T
VISOOU T
VISOOU T
a
OUTx
SEL
2M
EN_IOx
VCC I
VCC I
EN/FLT
VCC I
VCC I
VIO
VIO
550 k
INx
VIO
VIO
550 k
INx
Fault
1mA
Figure 9-5. Device I/O Schematics
46
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
10 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and
TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
10.1 Application Information
The device is a high-performance, quad channel digital isolator with integrated DC-DC converter. Typically digital
isolators require two power supplies isolated from each other to power up both sides of device. Due to the
integrated DC-DC converter in the device, the isolated supply is generated inside the device that can be used
to power isolated side of the device and peripherals on isolated side, thus saving board space. The device uses
single-ended CMOS-logic switching technology. When designing with digital isolators, keep in mind that because
of the single-ended design structure, digital isolators do not conform to any specific interface standard and are
only intended for isolating single-ended CMOS or TTL digital signal lines. The isolator is typically placed between
the data controller (that is Microcontroller or UART), and a data converter or a line transceiver, regardless of the
interface type or standard.
The device is suitable for applications that have limited board space and desire more integration. The device
is also suitable for very high voltage applications, where power transformers meeting the required isolation
specifications are bulky and expensive.
10.2 Typical Application
For step-by-step design procedure, circuit schematics, bill of materials, printed circuit board (PCB) files,
simulation results, and test results, refer to TI Design TIDA-01333, Eight-Channel, Isolated, High-Voltage
Analog Input Module With ISOW7841 Reference Design.
Figure 10-1 shows the typical schematic for SPI isolation.
Reference
10 F
1 F
10 nF
3.3 VIN
10 nF
1 F
10 F
VIO
VISOIN
CS
INA
OUTA
CS
SCLK
INB
OUTB
SCLK
SDO
INC
OUTC
SDI
3.3VOUT
DVCC
MCU
OUTD
SDI
DVSS
GNDIO
IND
VDD
1 F
10 nF
GND1
330 at 100 MHz
(BLM15EX331SN
1D)
VISOOUT
GND2
REF
ADC
SDO AGND
ISOW7741
GISOIN
VSEL
10 F
DVDD
AVDD
10 nF
1 F
10 F
HV+ to
Chassis
HV- to
Chassis
DGND
IN OUT
GND
330 at 100 MHz
(BLM15EX331SN
1D)
Optional LDO
Figure 10-1. Isolated Power and SPI for ADC Sensing Application with ISOW7741
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
47
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
10.2.1 Design Requirements
To design with this device, use the parameters listed in Table 10-1.
Table 10-1. Design Parameters
PARAMETER
VALUE
VDD input voltage
3 V to 5.5 V
VIO input voltage
1.71 V to 5.5 V
VISOIN input voltage
1.71 V to 5.5 V
VDD decoupling capacitors
10 µF + 1 µF + 0.01 µF + optional additional capacitance
VIO decoupling capacitors
0.1 µF + optional additional capacitance
VISOIN decoupling capacitors
0.1 µF + optional additional capacitance
VISOOUT decoupling capacitors
10 µF + 1 µF + 0.01 µF + optional additional capacitance
VISOOUT to VISOIN series inductor
BLM15ELX9331SN1D
GND2 to GISOIN series inductor
BLM15ELX9331SN1D
VIO series inductor
BLM15ELX9331SN1D
VDD series inductor
BLM15ELX9331SN1D
GND1 to GNDIO series inductor
BLM15ELX9331SN1D
Because of very-high current flowing through the ISOW7741 device device VDD and VISOOUT supplies, higher
decoupling capacitors typically provide better noise and ripple performance. Although a 10-µF capacitor is
adequate, higher decoupling capacitors (such as 47 µF) on both the VDD and VISOOUT pins to the respective
grounds are strongly recommended to achieve the best performance.
10.2.2 Detailed Design Procedure
The devices requires specific placement of external bypass capacitors and ferrite beads to operate at high
performance. These low-ESR ceramic bypass capacitors must be placed as close to the chip pads as possible.
48
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
10 F
10 F
VIO
330 at 100 MHz
(BLM15EX331SN1D)
1 F
1 F
10 nF
10 nF
VISOIN
1
20
INA
2
19
OUTA
INB
3
18
OUTB
INC
4
17
OUTC
OUTD
5
16
IND
6
15
7
14
8
13
9
12
10
11
GNDIO
EN_IO1
VIO
EN/FLT
FAULT OUT
EN_IO2
330
at 100 MHz
(BLM15EX331SN1D)
VDD
10 F
1 F
10 nF
GND1
330 at 100 MHz
(BLM15EX331SN1D)
GISOIN
VISOIN
VSEL
VISOOUT
330 at 100 MHz
(BLM15EX331SN1D)
VISOOUT
GND2 10 nF
VISOIN
1 F 10 F
330 at 100 MHz
(BLM15EX331SN1D)
Figure 10-2. Typical ISOW7741 Circuit Hook-Up
10.2.3 Application Curve
VDD = 5 V
VISOOUT = 5 V
IISOOUT = 100 mA
Figure 10-3. ISOW7741 Radiated Emissions versus CISPR32B line (Blue)
10.2.4 Insulation Lifetime
Insulation lifetime projection data is collected by using industry-standard Time Dependent Dielectric Breakdown
(TDDB) test method. In this test, all pins on each side of the barrier are tied together creating a two-terminal
device and high voltage applied between the two sides; See Figure 10-4 for TDDB test setup. The insulation
breakdown data is collected at various high voltages switching at 60 Hz over temperature. For reinforced
insulation, VDE standard requires the use of TDDB projection line with failure rate of less than 1 part per million
(ppm). Even though the expected minimum insulation lifetime is 20 years at the specified working isolation
voltage, VDE reinforced certification requires additional safety margin of 20% for working voltage and 87.5% for
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
49
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
lifetime which translates into minimum required insulation lifetime of 37.5 years at a working voltage that's 20%
higher than the specified value.
Figure 10-5 shows the intrinsic capability of the isolation barrier to withstand high voltage stress over its lifetime.
Based on the TDDB data, the intrinsic capability of the insulation is 1000 VRMS with a lifetime of 1184 years.
A
Vcc 1
Vcc 2
Time Counter
> 1 mA
DUT
GND 1
GND 2
VS
Oven at 150 °C
Figure 10-4. Test Setup for Insulation Lifetime Measurement
Figure 10-5. Insulation Lifetime Projection Data
50
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
11 Power Supply Recommendations
To help make sure that operation is reliable at data rates and supply voltages, adequate decoupling capacitors
must be located as close to supply pins as possible. VISOOUT needs to be connected to VISOIN to ensure the
feedback channel is properly powered to regulate the DC-DC converter. If VISOOUT and VISOIN are not connected,
the DC-DC converter will run open loop and the VISOOUT voltage will drift until the over-voltage clamp clamps at 6
V. There are two ways to connect VISOOUTand VISOIN:
1) connect VISOOUT and VISOIN directly with a ferrite bead. A ferrite bead is recommended between VISOOUTand
VISOIN to further reduce emissions.
2) connect VISOOUT and VISOIN with a ferrite bead through an LDO that remains powered up at all times. If the
LDO has an EN pin then keep the EN high at all times.
The input supply (VIO and VDD) must have an appropriate current rating to support output load and switching at
the maximum data rate required by the end application. For more information, refer to the Section 10.2 section.
For an output load current of 110 mA, it is recommended to have >600 mA of input current limit and for lower
output load currents, the input current limit can be proportionally lower.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
51
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
12 Layout
12.1 Layout Guidelines
A low cost two layer PCB should be sufficient to achieve good EMC performance:
•
•
•
•
Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/in2.
Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
If an additional supply voltage plane or signal layer is needed, add a second power or ground plane system
to the stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping.
Also the power and ground plane of each power system can be placed closer together, thus increasing the
high-frequency bypass capacitance significantly.
Because the device has no thermal pad to dissipate heat, the device dissipates heat through the respective GND
pins. Ensure that enough copper is present on both GND pins to prevent the internal junction temperature of the
device from rising to unacceptable levels.
Figure 12-1 shows the recommended placement and routing of device bypass capacitors. Below guidelines must
be followed to meet application EMC requirements:
•
•
•
•
•
•
High frequency bypass capacitors 10 nF must be placed close to VDD and VISOOUT pins, less than 1 mm
distance away from device pins. This is very essential for optimised radiated emissions performance. Ensure
that these capacitors are 0402 size so that they offer least inductance (ESL).
Bulk capacitors of atleast 10 μF must be placed on power converter input (VDD) and output (VISOOUT) supply
pins.
Traces on VDD and GND1 must be symmetric till bypass capacitors. Similarly traces on VISOOUT and GND2
must be symmetric.
Place two 0402 size Ferrite beads (Part number: BLM15EX331SN1) on VISOOUT and GND2 path so that any
high frequency noise from power converter output sees a high impedance before it goes to other components
on PCB.
Do not have any metal traces or ground pour within 4 mm of power converter output terminals VISOOUT pin12
and GND2 pin11. VSEL pin is also in VISOOUT domain and should be shorted to either pin 11 or pin 12 for
output voltage selection.
Following the layout guidelines of EVM as much as possible is highly recommended for a low radiated
emissions design.
12.1.1 PCB Material
For digital circuit boards operating at less than 150 Mbps, (or rise and fall times greater than 1 ns), and trace
lengths of up to 10 inches, use standard FR-4 UL94V-0 printed circuit board. This PCB is preferred over cheaper
alternatives because of lower dielectric losses at high frequencies, less moisture absorption, greater strength
and stiffness, and the self-extinguishing flammability-characteristics.
52
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: ISOW7740 ISOW7741 ISOW7742 ISOW7743 ISOW7744
ISOW7740, ISOW7741, ISOW7742, ISOW7743, ISOW7744
www.ti.com
SLLSFK1C – SEPTEMBER 2021 – REVISED APRIL 2022
12.2 Layout Example
FB
5
Input supply 1
C
C
C
10 F
1 F
10 nF
Ground plane on side 1
Ground plane on
side 2
工商网监
湘ICP备2023018690号
