LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
LM10502 Dual Buck + LDO Power Management Unit
Check for Samples: LM10502
FEATURES
DESCRIPTION
•
The LM10502 are advanced PMUs each containing
two configurable, high-efficiency buck regulators for
supplying variable voltages. The device is ideal for
supporting ASIC and SOC designs for Solid-State
and Flash drives.
1
2
•
•
Two Highly Efficient Programmable Buck
Regulators
– Integrated FETs with Low RDSON
– Bucks Operate with Their Phases Shifted to
Reduce the Input Current Ripple and
Capacitor Size
– Programmable Output Voltage via the SPI
interface
– Overvoltage and Undervoltage Lockout
– Automatic Internal Soft Start with Power-on
Reset
– Current Overload and Thermal Shutdown
Protection
– PFM Mode for Low-Load, High-Efficiency
Operation
Low-Dropout LDO 3.0V, 250 mA
SPI-Programmable Interrupt Comparator (2.0V
to 4.0V) to Monitor VIN
The LM10502 operate cooperatively with the
application ASIC to optimize the supply voltage for
low-power conditions and Power Saving modes via
the SPI interface. It also supports a 250 mA LDO and
a programmable Interrupt Comparator to monitor VIN.
APPLICATIONS
•
Solid-State Drives
KEY SPECIFICATIONS
•
•
•
•
•
LM10502 - Programmable Buck Regulators:
– Buck 1: 1.1V to 3.6V; 1A
– Buck 2: 0.7V to 1.335V; 1A
±3% Feedback Voltage Accuracy
Up to 95% Efficient Buck Regulators
2MHz Switching Frequency for Smaller
Inductor Size
2.5 x 2.5 mm, 0.5 mm Pitch DSBGA Package
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
Figure 1. Typical Application Diagram
LM 10502
IO input
supply
SPI_CS
3V
C1
a n d R E GI S T E R S
LDO_VOUT
LDO
4.7 uF
LDO_VIN
VIN
C6
Power Supply
C O N T R O L L O GI C
2.2 uF
3.0 / 5.5V
VIN_B1
C2
4.7 uF
GND
GND
GND
VIN_B2
C4
4.7 uF
2
RESET
VIN_IO
System
SPI_DI
SPI
SPI_DO
Control
SPI_CLK
VCOMP
COMP
VIN
IRQ
L1
1.8V
SW_B1
BUCK 1
2.2 uH
C3
22 uF
FLASH _I/O
1.8V /1A
FB_B1
L2
1.2 V
SW_B2
BUCK 2
FB_B2
Submit Documentation Feedback
2.2 uH
C5
22 uF
Host
Domain
Vccq
1.2V/1A
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Overview
The LM10502 contain two buck converters and one LDO. The table below list the output characteristics of the
power regulators.
SUPPLY SPECIFICATION
Table 1. Output Voltage Configurations for LM10502
(1)
Regulator
Start-Up
VOUT
Maximum Output
Current Iout-max
Typical
Application
Comments
Buck 1 (1)
1.8V
1.1V to 3.6V;
50 mV steps
1A
VCCQ
Flash
Buck 2 (1)
1.2V
0.7V to 1.335V;
5 mV steps
1A
VCore
Interface
LDO
3.0V
3.0V
250 mA
VHOST controller
Can be used to provide VVIN_IO
Default voltage values are determined when working in PWM mode. Voltage may be 0.8-1.6% higher when in PFM mode.
Connection Diagram and Package Marking
SPI _
CLK
RESET
VCOMP
VIN
5
SPI_CS
SPI_DO
4
VIN_IO
LDO_
OUT
LDO_
VIN
3
GND_B2
GND_B2
GND
GND_B1
GND_B1
2
SW_B2
NC
GND
NC
SW_B1
1
VIN_B2
FB_B2
IRQ
FB_B1
VIN_B1
A
B
SPI_DI
C
D
E
TOP VIEW
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
3
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
PIN DESCRIPTIONS
Pin #
Pin Name
I/O
Type Functional Description
E1
VIN_B1
I
P
Buck Switcher Regulator 1 - Power supply voltage input for power stage PFET.
E2
SW_B1
O
P
Buck Switcher Regulator 1 - Power Switching node, connect to inductor
D1
FB_B1
I
A
Buck Switcher Regulator 1 - Voltage output feedback for Buck Regulator 1
D3/E3
GND_B1
G
P
Buck Switcher Regulator 1 - Power ground for Buck Regulator
A1
VIN_B2
I
P
Buck Switcher Regulator 2 - Power supply voltage input for power stage PFET.
A2
SW_B2
O
P
Buck Switcher Regulator 2 - Power Switching node, connect to inductor
B1
FB_B2
I
A
Buck Switcher Regulator 2 - Voltage output feedback for Buck Regulator 2
A3/B3
GND_B2
G
P
Buck Switcher Regulator 2 - Power ground for Buck Regulator
E4
VIN
I
P
Power supply Input Voltage, must be present for device to work
C4
LDO_VIN
I
P
LDO Regulator - LDO input voltage can be only come from bump D4/E4 -VIN or if not used has to
be connected to C3-GND
B4
LDO_OUT
O
P
LDO Regulator - LDO output voltage can only be connected to bump A4 to provide VIN_IO or is not
used
A4
VIN_IO
P
A
Supply Voltage for Digital Interface can be supplied from any external supply or bump B4 LDO_OUT
A5
SPI_CS
I
D
SPI Interface – chip select
C5
SPI_DI
I
D
SPI Interface – serial data input
B5
SPI_DO
O
D
SPI Interface – serial data output
D5
SPI_CLK
I
D
SPI Interface – serial clock input
E5
RESET
I
D
Digital Input Control Signal to abort SPI transactions and resets the PMIC to default Voltages
D4
VCOMP
I
A
Analog Input for Comparator. Can only be connected to monitor E4-VIN
C1
IRQ
O
D
Digital Output of Comparator to signal Interrupt condition from Comparator input VIN
C3
GND
G
G
Ground. Connect to system Ground.
C2
GND
G
G
Ground. Connect to system Ground.
B2
NC
Do not connect
D2
NC
Do not connect
Absolute Maximum Ratings (1)
(2)
−0.3V to +6.0V
VIN, VCOMP
VIN_IO, VIN_B1, VIN_B2, SPI_CS, SPI_DI, SPI_CLK, SPI_DO, RESET, IRQ
Junction Temperature (TJ-MAX)
150°C
−65°C to 150°C
Storage Temperature
ESD Rating
(1)
(2)
4
−0.3V to VVIN
Human Body Model (HBM)
2.0kV
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is ensured. Operating Ratings do not imply ensured performance limits. For ensured performance limits and
associated test conditions, see the General Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Operating Ratings (1)
(2) (3)
VIN_B1, VIN_B2_VIN_B3, VIN
3.0V to 5.5V
VIN_IO
1.72V to 3.63V and < VVIN
All pins except VIN_IO
0V to VVIN
−30°C to 125°C
Junction Temperature (TJ)
−30°C to 85°C
Ambient Temperature (TA)
Junction-to-Ambient Thermal Resistance (θJA)
(1)
Maximum Continuous Power Dissipation (PD-MAX)
(1)
(2)
(3)
42.1°C/W
(1)
0.95W
In applications where high power dissipation and/or poor thermal resistance is present the maximum ambient temperature may have to
be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = +125°C),
the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the
part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX).
The amount of Absolute Maximum power dissipation allowed for the device depends on the ambient temperature and can be calculated
using the formula: P = (TJ–TA)/θJA, where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-toambient thermal resistance. θJA is highly application and board-layout dependent. Internal thermal shutdown circuitry protects the device
from permanent damage. (See General Electrical Characteristics.)
Internal thermal shutdown protects device from permanent damage. Thermal shutdown engages at TJ = +140°C and disengages at TJ =
+120°C (typ.). Thermal shutdown is ensured by design.
General Electrical Characteristics (1)
(2)
Unless otherwise noted, VVIN = 5.0V, VVIN_IO = 3.0V.
The application circuit used is the one shown in "Typical Application Circuit."
Limits in standard typeface are for T,= 25°C.
Limits appearing in boldface type apply over the entire operating junction temperature range of −30°C ≤ TA = TJ ≤ +85°C.
Symbol
Parameter
Quiescent Supply
Current
IQ
Conditions
Min
Typ
Max
Units
60
130
µA
2.75
2.9
3.05
2.45
2.6
2.75
BUCK1 OFF, BUCK2 PFM
no load,LDO SLEEP
UNDER/OVERVOLTAGE LOCK OUT
VUVLO_RISING
VUVLO_FALLING
VOVLO_RISING
VOVLO_FALLING
Under Voltage Lock
Out
5.7
Over Voltage Lock
Out
V
5.6
DIGITAL INTERFACE
VVIN_IO
Input Supply for digital
VVIN_IO ≤ V VIN
interface
VIL
Logic input low
VIH
Logic input high
VOL
Logic output low
VOH
Logic output high
IIL
Input current, pin
driven low
SPI_CS, SPI_DI, SPI_CLK,
−2
RESET
−5
IIH
Input current, pin
driven high
SPI_CS, SPI_DI, SPI_CLK,
RESET
fSPI_MAX
SPI max frequency
tRESET
Minimum high-pulse
width (3)
(1)
(2)
(3)
SPI_CS, SPI_DI, SPI_CLK,
RESET,
SPI_DO
1.72
3.63
0.3*VVIN_IO
V
0.7*VVIV_IO
0.2*VVIN_IO
0.8*VVIN_IO
µA
2
µA
10
MHz
2
µsec
All limits are ensured by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested
during production with TJ = 25°C. All hot and cold limits are ensured by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Capacitors: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) are used in setting electrical characteristics.
Specification ensured by design. Not tested during production.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
5
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
Buck 1 Electrical Characteristics (1)
(2) (3)
Unless otherwise noted, VIN = 5.0V where: VIN=VVIN_B1 = VVIN_B2. L1 = 2.2µH,C3=C5=22µF,C2=C4=4.7µF.
The application circuit used is the one shown in "Typical Application Circuit."
Limits in standard typeface are for TJ = 25°C.
Limits appearing in boldface type apply over the entire operating junction temperature range of −30°C ≤ TA = TJ ≤ +85°C.
Symbol
Parameter
Conditions
IQ
DC Bias Current in VIN
No Load, PFM Mode
IOUT-MAX
Continuous load current( (4)
(5) (6) (7)
)
Buck 1 enabled switching in PWM
1.0
IPEAK
Peak switching current limit
Buck 1 enabled, switching in PWM
1.3
η
Efficiency peak, Buck 1 (5)
IOUT = 0.3A, VIN = 5.0V
FSW
Switching Frequency
CIN
Input Capacitor
Output Capacitor ESR (5)
Typ
Max
Units
15
50
µA
1.575
1.85
90
1.75
(5)
Output Filter Capacitor (5)
COUT
Min
2
2.3
4.7
10
0mA ≤ IOUT ≤ -IOUT-MAX
22
A
%
100
20
MHz
µF
mΩ
L
Output Filter Inductance (5)
VFB
Feedback Voltage
VOUT = 1.8V (Default) PWM Mode,No Load
DC Line regulation (5)
3.3V ≤ VIN ≤ 5.0V, IOUT-MAX
0.5
%/V
DC Load regulation (5)
100mA ≤ IOUT-MAX
0.3
%/A
IFB
Feedback pin input bias
current
VFB = 1.8V
2.4
RDS-ON-HS
High Side Switch On
Resistance
VIN = 5.0V
140
VIN = 2.6V
220
RDS-ON-LS
Low Side Switch On
Resistance
VIN = 5.0V
70
Internal soft-start (turn on
time) (5)
Startup from shutdown, VOUT = 0V, no load, LC =
recommended circuit, using software enable, to
VOUT = 95% of final value
0.1
ΔVOUT
2.2
-3
µH
3
5
%
µA
mΩ
150
mΩ
STARTUP
TSTART
(1)
(2)
(3)
(4)
(5)
(6)
(7)
6
ms
All limits are ensured by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested
during production with TJ = 25°C. All hot and cold limits are ensured by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Capacitors: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) are used in setting electrical characteristics.
BUCK normal operation is ensured if VIN ≥ VOUT+1.0V.
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is ensured. Operating Ratings do not imply ensured performance limits. For ensured performance limits and
associated test conditions, see the General Electrical Characteristics.
Specification ensured by design. Not tested during production.
In applications where high power dissipation and/or poor thermal resistance is present the maximum ambient temperature may have to
be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = +125°C),
the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the
part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX).
The amount of Absolute Maximum power dissipation allowed for the device depends on the ambient temperature and can be calculated
using the formula: P = (TJ–TA)/θJA, where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-toambient thermal resistance. θJA is highly application and board-layout dependent. Internal thermal shutdown circuitry protects the device
from permanent damage. (See General Electrical Characteristics.)
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Buck 2 Electrical Characteristics (1)
(2) (3)
Unless otherwise noted, VIN = 5.0V where: VIN=VVIN_B1 = VVIN_B2. L1 = 2.2µH,C3=C5=22µF,C2=C4=4.7µF.
The application circuit used is the one shown in "Typical Application Circuit."
Limits in standard typeface are for TJ = 25°C.
Limits appearing in boldface type apply over the entire operating junction temperature range of −30°C ≤ TA = TJ ≤ +85°C.
Symbol
Parameter
Conditions
Min
IQ
DC Bias Current in VIN
No Load, PFM Mode
IOUT-MAX
Continuous load current( (4)
(5) (6) (7)
)
Buck 1 enabled switching in PWM
1.0
IPEAK
Peak switching current limit
Buck 1 enabled, switching in PWM
1.3
η
Efficiency peak, Buck 2 (5)
IOUT = 0.3A,VIN = 5.0V
FSW
Switching Frequency
CIN
Input Capacitor
COUT
Output Capacitor ESR (5)
Max
Units
15
50
µA
1.575
1.85
90
1.75
(5)
Output Filter Capacitor (5)
Typ
2
2.3
4.7
0mA ≤ IOUT ≤ -IOUT-MAX
10
22
A
%
100
20
MHz
µF
mΩ
L
Output Filter Inductance (5)
VFB
Feedback Voltage
VOUT = 1.2V (Default) PWM Mode,No Load
DC Line regulation (5)
3.3V ≤ VIN ≤ 5.0V, IOUT = IOUT-MAX
0.5
%/V
DC Load regulation (5)
100 mA ≤ IOUT ≤ IOUT-MAX
0.3
%/A
IFB
Feedback pin input bias
current
VFB = 1.2V
1.6
RDS-ON-HS
High Side Switch On
Resistance
VIN = 5.0V
140
VIN = 2.6V
220
RDS-ON-LS
Low Side Switch On
Resistance
VIN = 5.0V
70
Internal soft-start (turn on
time) (5)
Startup from shutdown, VOUT = 0V, no load, LC =
recommended circuit, using software enable, to
VOUT = 95% of final value
0.1
ΔVOUT
2.2
-3
µH
3
4
%
µA
mΩ
150
STARTUP
TSTART
(1)
(2)
(3)
(4)
(5)
(6)
(7)
ms
All limits are ensured by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested
during production with TJ = 25°C. All hot and cold limits are ensured by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Capacitors: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) are used in setting electrical characteristics.
BUCK normal operation is ensured if VIN ≥ VOUT+1.0V.
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is ensured. Operating Ratings do not imply ensured performance limits. For ensured performance limits and
associated test conditions, see the General Electrical Characteristics.
Specification ensured by design. Not tested during production.
In applications where high power dissipation and/or poor thermal resistance is present the maximum ambient temperature may have to
be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = +125°C),
the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the
part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX).
The amount of Absolute Maximum power dissipation allowed for the device depends on the ambient temperature and can be calculated
using the formula: P = (TJ–TA)/θJA, where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-toambient thermal resistance. θJA is highly application and board-layout dependent. Internal thermal shutdown circuitry protects the device
from permanent damage. (See General Electrical Characteristics.)
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
7
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
LDO Electrical Characteristics (1)
www.ti.com
(2)
Unless otherwise noted, VIN = 5.0V where: VIN=VVIN = VVIN_LDO. C1 = 4.7µF,C6 = 2.2µF.
The application circuit used is the one shown in "Typical Application Circuit."
Limits in standard typeface are for TJ = 25°C.
Limits appearing in boldface type apply over the entire operating junction temperature range of −30°C ≤ TA = TJ ≤ +85°C.
Symbol
Parameter
VOUT
Output Voltage Accuracy
IOUT
Maximum Output Current
ISC
Short Circuit Current Limit
VDO
Dropout Voltage
ΔVOUT
Conditions
Ma
x
Uni
ts
+3
%
250
(4)
mA
Vout = 0V (3), VIN =3.3V
0.5
5
IOUT = 250mA
175 240
Line Regulation
3.3V ≤ VIN ≤ 5.5V, IOUT = 1mA
Load Regulation
1mA ≤ IOUT ≤ 250 mA, VIN = 3.3V, 5.0V
Output Noise Voltage (3)
PSRR
Power Supply Rejection Ratio (3)
F = 10 kHz,
IOUT = 20 mA
tSTARTUP
Startup Time from Shutdown (3)
IOUT = 250 mA
TTRANSIENT
Startup Transient Overshoot (3)
IOUT = 250 mA
(2)
(3)
(4)
−3
IOUT = 1mA,VOUT = 3V
eN
(1)
Min Typ
A
5
mV
5
10 Hz ≤ f ≤ 100 kHz
VIN = 5.0V
10
µVR
VIN = 3.3V
35
MS
VIN = 5.0V
65
dB
VIN = 3.3V
40
VIN = 5.0V
45
VIN = 3.3V
60
µs
30
mV
All limits are ensured by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested
during production with TJ = 25°C. All hot and cold limits are ensured by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Capacitors: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) are used in setting electrical characteristics.
Specification ensured by design. Not tested during production.
Dropout voltage is the difference between the input and output at which the output voltage drops to 100mV below its nominal value.
Comparators Electrical Characteristics (1)
(2)
Unless otherwise noted, VIN = 5.0V where: VIN=VVIN = VVIN_LDO.
The application circuit used is the one shown in "Typical Application Circuit."
Limits in standard typeface are for TJ = 25°C.
Limits appearing in boldface type apply over the entire operating junction temperature range of −30°C ≤ TA = TJ ≤ +85°C.
Symbol
Parameter
Conditions
VCOMP = 0.0V
Min
Typ
-2
0.1
IVCOMP
VCOMP pin bias current
VVCOMP_RISE
VCOMP input rising
edge trigger level
2.826
VVCOMP_FALL
VCOMP input falling
edge trigger level
2.768
VCOMP = 5.0V
30
VOH
IRQ Output voltage high
@2mA
VOL
IRQ Output voltage low
@2mA
tCOMP
Transition time of
Interrupt to IRQ pin
output
(2)
8
2
Units
µA
V
Hysteresis
(1)
0.1
Max
60
80
0.8*VIN_IO
0.2*VIN_IO
6
15
mV
V
µsec
All limits are ensured by design, test and/or statistical analysis. All electrical characteristics having room-temperature limits are tested
during production with TJ = 25°C. All hot and cold limits are ensured by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Capacitors: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) are used in setting electrical characteristics.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Typical Performance Characteristics
Efficiency of Buck 2: VIN=3.3V, VOUT=1.8V and 2.0V
100
90
90
80
80
70
70
EFFICIENCY %
EFFICIENCY %
Efficiency of Buck 1: VIN=3.3V, VOUT=1.8V
100
60
50
40
30
60
50
40
30
20
20
10
10
0
0
10m
100m
IOUT(A)
Figure 2.
1
10m
Startup of Buck 1: VIN=3.3V
(VOUT=1.8V, IOUT=1.0A)
1 1.00V/
200 Ps/
100m
IOUT(A)
Figure 3.
1
LDO VOUT
vs.
LDO VVIN
3.05
VIN=3.3V
3.04
3.03
VIN = 3.3V
1A load
VOUT ( V)
3.02
3.01
3.00
2.99
2.98
1
BUCK1
2.97
2.96
2.95
0 25 50 75 100125150175200225250
IOUT (mA)
Figure 5.
Figure 4.
3.036
LDO VIN
vs.
VOUT
Buck 1 VOUT vs. IOUT
VIN=3.3V, VOUT=1.8V
1.840
Current Load = 1mA
1.835
3.034
1.830
VOUT (V)
VOUT(V)
1.825
3.032
3.030
1.820
1.815
1.810
1.805
3.028
1.800
1.795
3.026
1.790
3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5
VIN (V)
Figure 6.
0
200
400
600
IOUT (mA)
Figure 7.
800
1000
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
9
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Buck 2 VOUT vs. IOUT
VIN=3.3V, VOUT=1.2V
1.24
Buck 1LOAD TRANSIENT
VIN=3.3V, VOUT=1.8V
1.23
Load 0-400-0 mA
VOUT (v)
1.22
1.21
1.20
1.19
50mV/div
Output Voltage
1.18
0
200
400
600
IOUT (mA)
Figure 8.
800
1000
Figure 9.
Buck 2 LOAD TRANSIENT
VIN=3.3V, VOUT=1.2V
Buck 1 LOAD TRANSIENT 1A
VIN=3.3V, VOUT=1.8V COUT=70µF
Load 0-600-0mA
Load 0-1Amp-0
50mV/div
50mV/div
Output Voltage
Output Voltage
Figure 10.
Figure 11.
Buck 2 LOAD TRANSIENT 1A
VIN=3.3V, VOUT=1.2V COUT=70µF
1.95
Buck 1 VOUT vs. VIN
VOUT=1.8V, IOUT=400mA
1.90
Load 0-1Amp-0
VOUT (V)
1.85
1.80
1.75
1.70
50 s/div
50mV/div
Output Voltage
1.65
3.5
Figure 12.
10
Submit Documentation Feedback
4.0
4.5
VIN(V)
Figure 13.
5.0
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Typical Performance Characteristics (continued)
1.45
Buck 2 VOUT vs. VIN
VOUT=1.2V, IOUT=600mA
LDO Startup Time from VIN Rise
1 1.00V/ 2 1.00V/
5.00 ms/
1.40
1.35
VOUT (V)
1.30
1.25
1.20
1.15
1.10
1.05
1.00
0.95
3.5
4.0
4.5
1
VIN
2
LDO
5.0
VIN (V)
Figure 14.
Figure 15.
From LDO Startup to Buck 1 Startup
1 1.00V/ 2 1.00V/
From Buck 1 Startup to Buck 2 Startup
1.00 ms/
1 1.00V/ 2 1.00V/
1
LDO
1
BUCK1
2
BUCK1
2
BUCK2
Figure 16.
1.00 ms/
Figure 17.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
11
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
GENERAL DESCRIPTION
LM10502 is a highly efficient and integrated Power Management Unit for Systems-on-a-Chip (SoCs), ASICs, and
processors. It operates cooperatively and communicates with processors over an SPI interface with output
Voltage programmability.
GND
GND
GND
VIN
LDO_OUT
LDO_VIN
SPI
SPI_CLK
SPI_DO
SPI_DI
SPI_CS
VIN_IO
The device incorporates two high-efficiency synchronous buck regulators and one LDO that deliver four output
voltages from a single power source. The device also includes a SPI-programmable Comparator Block that
provides an interrupt output signal.
LDO
RESET
CONTROL REGISTERS
STANDBY LOGIC
EN
VIN_B2
SW2
FB_B2
EN
BUCK2
SW_B2
GND_B2
VIN_B1
SW_B1
GND_B1
EN
SW1
BUCK1
SEQUENCER
TSD
FB_B1
UVLO
OVLO
EN
VCOMP
COMPARATOR
IRQ
Figure 18. Internal Block Diagram of the LM10502 PMIC
12
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
SPI DATA INTERFACE
The device is programmable via 4-wire SPI Interface. The signals associated with this interface are CS, DI, DO
and CLK. Through this interface, the user can enable/disable the device, program the output voltages of the
individual Bucks and of course read the status of Flag registers.
By accessing the registers in the device through this interface, the user can get access and control the operation
of the buck controllers and program the reference voltage of the comparator in the device.
CS
CLK
DI
1
1
2
0
3
A4
Write
Command
DO
7
A3
A2
A1
A0
9
0
D7
16
D6
D5
D4
D3
D2
D1
D0
Write Data
Register Address
0
Figure 19. SPI Interface Write
•
•
Data In (DI)
– 1 to 0 Write Command
– A4to A0 Register address to be written
– D7 to D0 Data to be written
Data Out (DO)
– All Os
CS
CLK
DI
1
1
2
1
Read
Command
3
A4
7
A3
A2
A1
A0
9
16
0
Register Address
DO
D7
D6
D5
D4
D3
D2
D1
D0
Read Data
Figure 20. SPI Interface Read
•
•
Data In (DI)
– 1 to 1 Read Command
– A4to A0 Register address to be read
Data Out (DO)
– D7 to D0 Data Read
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
13
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
Registers Configurable Via The SPI Interface
Addr
0x00
0x07
Reg Name
Buck 2 Voltage
Bit
0x09
Reserved
0x0A
Buck Control
Description
—
6
R/W
Buck 2 Voltage Code[6]
5
R/W
Buck 2 Voltage Code[5]
4
R/W
3
R/W
2
R/W
Buck 2 Voltage Code[2]
1
R/W
Buck 2 Voltage Code[1]
0
R/W
Buck 2 Voltage Code[0]
Reserved
Buck 1 Voltage
Default
7
0x64
0x0B
0x0C
(1)
14
Interrupt Enable
0x64 (1.2V)
Buck 2 Voltage Code[4]
Buck 2 Voltage Code[3]
Range: 0.7V to 1.335V
Do Not use
—
(1)
Reset default:
6
—
5
R/W
0x0E (1.8V)
4
R/W
3
R/W
2
R/W
Buck 1 Voltage Code[2]
1
R/W
Buck 1 Voltage Code[1]
0
R/W
Buck 1 Voltage Code[0]
Buck 1 Voltage Code[5]
0x0E
Buck 1 Voltage Code[4]
Buck 1 Voltage Code[3]
Range: 1.1V to 3.6V
Do not use. (1)
7
—
6
—
5
—
Do not use. (1)
Do not use. (1)
4
Comparator
Control
Notes
Reset default:
——
7
0x08
R/W
3
R/W
0
BK1FPWM
Buck 1 forced PWM mode when high
2
R/W
0
BK2FPWM
Buck 2 forced PWM mode when high
1
R/W
-
0
R/W
1
BK1EN
Enables Buck 1 0-disabled, 1-enabled
7
R/W
0
Comp_hyst[0]
Doubles Comparator hysteresis
6
R/W
0
Comp_thres[5]
Programmable range of 2.0V to 4.0V, step
size = 31.75 mV;
5
R/W
1
Comp_thres[4]
4
R/W
1
Comp_thres[3]
Comparator Threshold reset default:
3
R/W
0
Comp_thres[2]
0x19;
2
R/W
0
Comp_thres[1]
Comp_hyst=1 → min 80 mV hysteresis
1
R/W
1
Comp_thres[0]
Comp_hyst=0 → min 40 mV hysteresis
0
R/W
1
COMPEN
Comparator enable
7
—
6
—
Do not use. (1)
5
—
4
R/W
0
LDO OK
3
R/W
0
Buck 2 OK
2
R/W
0
Buck 1 OK
1
R/W
0
-
Do not use. (1)
0
R/W
1
Comparator
Interrupt comp event
RESERVED FOR FIRMWARE COMPATIBILITY WITH LM10506
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
Addr
0x0D
0x0E
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Reg Name
Interrupt Status
MISC Control
Bit
R/W
7
—
Default
Description
6
—
5
—
4
R
LDO OK
LDO is greater than 90% of target
3
R
Buck 2 OK
Buck 2 is greater than 90% of target
2
R
Buck 1 OK
Buck 1 is greater than 90% of target
1
R
-
Do not use. (1)
0
R
Comparator
Comparator output is high
7
—
6
—
5
—
4
—
3
—
LDO goes into extra power save mode
2
—
1
R/W
0
LDO Sleep Mode
0
R/W
0
Interrupt Polarity
Notes
Interrupt_polarity= 0→ Active low
Interrupt_polarity= 1→ Active high
ADDR 0x07& 0x08: Buck 1 Voltage Code and VOUT Level Mapping
Voltage code
Voltage
Voltage code
Voltage
0x00
1.10
0x20
2.70
0x01
1.15
0x21
2.75
0x02
1.20
0x22
2.80
0x03
1.25
0x23
2.85
0x04
1.30
0x24
2.90
0x05
1.35
0x25
2.95
0x06
1.40
0x26
3.00
0x07
1.45
0x27
3.05
0x08
1.50
0x28
3.10
0x09
1.55
0x29
3.15
0x0A
1.60
0x2A
3.20
0x0B
1.65
0x2B
3.25
0x0C
1.70
0x2C
3.30
0x0D
1.75
0x2D
3.35
0x0E
1.80
0x2E
3.40
0x0F
1.85
0x2F
3.45
0x10
1.90
0x30
3.50
0x11
1.95
0x31
3.55
0x12
2.00
0x32
3.60
0x13
2.05
0x33
3.60
0x14
2.10
0x34
3.60
0x15
2.15
0x35
3.60
0x16
2.20
0x36
3.60
0x17
2.25
0x37
3.60
0x18
2.30
0x38
3.60
0x19
2.35
0x39
3.60
0x1A
2.40
0x3A
3.60
0x1B
2.45
0x3B
3.60
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
15
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
Voltage code
Voltage
Voltage code
Voltage
0x1C
2.50
0x3C
3.60
0x1D
2.55
0x3D
3.60
0x1E
2.60
0x3E
3.60
0x1F
2.65
0x3F
3.60
ADDR 0x00: Buck 2 Voltage Code and VOUT Level Mapping
16
Voltage Code
Voltage
Voltage Code
Voltage
Voltage Code
Voltage
Voltage Code
Voltage
0x00
0.700
0x20
0.860
0x40
1.020
0x60
1.180
0x01
0.705
0x21
0.865
0x41
1.025
0x61
1.185
0x02
0.710
0x22
0.870
0x42
1.030
0x62
1.190
0x03
0.715
0x23
0.875
0x43
1.035
0x63
1.195
0x04
0.720
0x24
0.880
0x44
1.040
0x64
1.200
0x05
0.725
0x25
0.885
0x45
1.045
0x65
1.205
0x06
0.730
0x26
0.890
0x46
1.050
0x66
1.210
0x07
0.735
0x27
0.895
0x47
1.055
0x67
1.215
0x08
0.740
0x28
0.900
0x48
1.060
0x68
1.220
0x09
0.745
0x29
0.905
0x49
1.065
0x69
1.225
0x0A
0.750
0x2A
0.910
0x4A
1.070
0x6A
1.230
0x0B
0.755
0x2B
0.915
0x4B
1.075
0x6B
1.235
0x0C
0.760
0x2C
0.920
0x4C
1.080
0x6C
1.240
0x0D
0.765
0x2D
0.925
0x4D
1.085
0x6D
1.245
0x0E
0.770
0x2E
0.930
0x4E
1.090
0x6E
1.250
0x0F
0.775
0x2F
0.935
0x4F
1.095
0x6F
1.255
0x10
0.780
0x30
0.940
0x50
1.100
0x70
1.260
0x11
0.785
0x31
0.945
0x51
1.105
0x71
1.265
0x12
0.790
0x32
0.950
0x52
1.110
0x72
1.270
0x13
0.795
0x33
0.955
0x53
1.115
0x73
1.275
0x14
0.800
0x34
0.960
0x54
1.120
0x74
1.280
0x15
0.805
0x35
0.965
0x55
1.125
0x75
1.285
0x16
0.810
0x36
0.970
0x56
1.130
0x76
1.290
0x17
0.815
0x37
0.975
0x57
1.135
0x77
1.295
0x18
0.820
0x38
0.980
0x58
1.140
0x78
1.300
0x19
0.825
0x39
0.985
0x59
1.145
0x79
1.305
0x1A
0.830
0x3A
0.990
0x5A
1.150
0x7A
1.310
0x1B
0.835
0x3B
0.995
0x5B
1.155
0x7B
1.315
0x1C
0.840
0x3C
1.000
0x5C
1.160
0x7C
1.320
0x1D
0.845
0x3D
1.005
0x5D
1.165
0x7D
1.325
0x1E
0.850
0x3E
1.010
0x5E
1.170
0x7E
1.330
0x1F
0.855
0x3F
1.015
0x5F
1.175
0x7F
1.335
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
ADDR 0x0B: Comparator Threshold Mapping
Voltage code
Voltage
Voltage code
Voltage
0x00
2.000
0x20
3.016
0x01
2.032
0x21
3.048
0x02
2.064
0x22
3.080
0x03
2.095
0x23
3.111
0x04
2.127
0x24
3.143
0x05
2.159
0x25
3.175
0x06
2.191
0x26
3.207
0x07
2.222
0x27
3.238
0x08
2.254
0x28
3.270
0x09
2.286
0x29
3.302
0x0A
2.318
0x2A
3.334
0x0B
2.349
0x2B
3.365
0x0C
2.381
0x2C
3.397
0x0D
2.413
0x2D
3.429
0x0E
2.445
0x2E
3.461
0x0F
2.476
0x2F
3.492
0x10
2.508
0x30
3.524
0x11
2.540
0x31
3.556
0x12
2.572
0x32
3.588
0x13
2.603
0x33
3.619
0x14
2.635
0x34
3.651
0x15
2.667
0x35
3.683
0x16
2.699
0x36
3.715
0x17
2.730
0x37
3.746
0x18
2.762
0x38
3.778
0x19
2.794
0x39
3.810
0x1A
2.826
0x3A
3.842
0x1B
2.857
0x3B
3.873
0x1C
2.889
0x3C
3.905
0x1D
2.921
0x3D
3.937
0x1E
2.953
0x3E
3.969
0x1F
2.984
0x3F
4.000
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
17
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
BUCK REGULATORS OPERATION
A buck converter contains a control block, a switching PFET connected between input and output, a synchronous
rectifying NFET connected between the output and ground and a feedback path. The following figure shows the
block diagram of each of the two buck regulators integrated in the device.
CONTROL
G
CIN
P
D
D
SW
N
S
L
VOUT
G
FB
S
VIN
PVIN
U1
LM10502
COUT
PGND
GND
Figure 21. Buck Functional Diagram
During the first portion of each switching cycle, the control block turns on the internal PFET switch. This allows
current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the
current to a ramp with a slope of (VIN – VOUT)/L by storing energy in a magnetic field. During the second portion
of each cycle, the control block turns the PFET switch off, blocking current flow from the input, and then turns the
NFET synchronous rectifier on. The inductor draws current from ground through the NFET to the output filter
capacitor and load, which ramps the inductor current down with a slope of (–VOUT)/L.
The output filter stores charge when the inductor current is high, and releases it when low, smoothing the voltage
across the load. The output voltage is regulated by modulating the PFET switch on time to control the average
current sent to the load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the
switch and synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter
capacitor. The output voltage is equal to the average voltage at the SW pin.
Buck Regulators Description
The LM10502 incorporates two high-efficiency synchronous switching buck regulators that deliver various
voltages from a single DC input voltage. They include many advanced features to achieve excellent voltage
regulation, high efficiency and fast transient response time. The bucks feature voltage mode architecture with
synchronous rectification.
Each of the switching regulators is specially designed for high-efficiency operation throughout the load range.
With a 2MHz typical switching frequency, the external L- C filter can be small and still provide very low output
voltage ripple. The bucks are internally compensated to be stable with the recommended external inductors and
capacitors as detailed in the application diagram. Synchronous rectification yields high efficiency for low voltage
and high output currents.
All bucks can operate up to a 100% duty cycle allowing for the lowest possible input voltage that still maintains
the regulation of the output. The lowest input to output dropout voltage is achieved by keeping the PMOS switch
on.
Additional features include soft-start, undervoltage lockout, bypass, and current and thermal overload protection.
To reduce the input current ripple, the device employs a control circuit that operates the two bucks at 180°
phase. These bucks are nearly identical in performance and mode of operation. They can operate in FPWM
(forced PWM) or automatic mode (PWM/PFM).
18
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
PWM Operation
During PWM operation the converter operates as a voltage-mode controller with input voltage feed forward. This
allows the converter to achieve excellent load and line regulation. The DC gain of the power stage is proportional
to the input voltage. To eliminate this dependence, a feed forward voltage inversely proportional to the input
voltage is introduced.
In Forced PWM Mode the bucks always operate in PWM mode regardless of the output current.
In Automatic Mode, if the output current is less than 70 mA (typ.), the bucks automatically transition into PFM
(Pulse Frequency Modulation) operation to reduce the current consumption, while at higher than 70mA (typ) they
operate in PWM mode. This increases the efficiency at lower output currents.
PWM Mode at
Moderate to
Heavy Loads
VOUT
PFM Mode at Light Load
Load current
increases, draws
Vout towards Low 2
PFM Threshold
High PFM
Threshold
~1.016*VOUT
Low1 PFM
Threshold
~1.008*VOUT
PFET on
until
LPFM
limit
reached
NFET on
drains
inductor
current
until
I inductor=0
High PFM
Voltage
Threshold
reached,
go into
idle mode
Low PFM
Threshold,
turn on
PFET
Load
current
increases
Low 2 PFM
Threshold,
switch back to
PWM mode
Low2 PFM
Threshold
VOUT
Time
Figure 22. PFM vs PWM Operation
PFM Operation (Bucks 1 & 2)
At very light loads, Buck 1, and Buck 2 enter PFM mode and operate with reduced switching frequency and
supply current to maintain high efficiency.
Buck 1, and 2 will automatically transition into PFM mode when either of two conditions occurs for a duration of
32 or more clock cycles:
1. The inductor current becomes discontinuous, or
2. The peak PMOS switch current drops below the IMODE level.
During PFM operation, the converter positions the output voltage slightly higher than the nominal output voltage
during PWM operation, allowing additional headroom for voltage drop during a load transient from light to heavy
load. The PFM comparators sense the output voltage via the feedback pin and control the switching of the output
FETs such that the output voltage ramps between 0.8% and 1.6% (typical) above the nominal PWM output
voltage. If the output voltage is below the ‘high’ PFM comparator threshold, the PMOS power switch is turned on.
It remains on until the output voltage exceeds the ‘high’ PFM threshold or the peak current exceeds the IPFM level
set for PFM mode.
Once the PMOS power switch is turned off, the NMOS power switch is turned on until the inductor current ramps
to zero. When the NMOS zero-current condition is detected, the NMOS power switch is turned off. If the output
voltage is below the ‘high’ PFM comparator threshold (see Figure 22), the PMOS switch is again turned on and
the cycle is repeated until the output reaches the desired level. Once the output reaches the ‘high’ PFM
threshold, the NMOS switch is turned on briefly to ramp the inductor current to zero and then both output
switches are turned off and the part enters an extremely low power mode. Quiescent supply current during this
‘idle’ mode is less than 100 µA, which allows the part to achieve high efficiencies under extremely light load
conditions. When the output drops below the ‘low’ PFM threshold, the cycle repeats to restore the output voltage
to ~1.6% above the nominal PWM output voltage.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
19
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
If the load current should increase during PFM mode causing the output voltage to fall below the ‘low2’ PFM
threshold, the part will automatically transition into fixed-frequency PWM mode.
Soft Start
Each of the buck converters has an internal soft-start circuit that limits the in-rush current during startup. This
allows the converters to gradually reach the steady-state operating point, thus reducing startup stresses and
surges. During startup, the switch current limit is increased in steps.
For Buck 1 and 2 the soft start is implemented by increasing the switch current limit in steps that are gradually
set higher. The startup time depends on the output capacitor size, load current and output voltage. Typical
startup time with the recommended output capacitor of 22 µF is 0.2 to 1ms. It is expected that in the final
application the load current condition will be more likely in the lower load current range during the start up.
Current Limiting
A current limit feature protects the device and any external components during overload conditions. In PWM
mode the current limiting is implemented by using an internal comparator that trips at current levels according to
the buck capability. If the output is shorted to ground the device enters a timed current limit mode where the
NFET is turned on for a longer duration until the inductor current falls below a low threshold, ensuring inductor
current has more time to decay, thereby preventing runaway.
Internal Synchronous Rectification
While in PWM mode, the bucks use an internal NFET as a synchronous rectifier to reduce the rectifier forward
voltage drop and the associated power loss. Synchronous rectification provides a significant improvement in
efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier
diode.
Low Dropout Operation
The device can operate at 100% duty cycle (no switching; PMOS switch completely on) for low dropout support.
In this way the output voltage will be controlled down to the lowest possible input voltage. When the device
operates near 100% duty cycle, output voltage ripple is approximately 25 mV.
The minimum input voltage needed to support the output voltage:
VIN_MIN=VOUT+ILOAD*(RDSON_PFET+RIND)
Where,
•
•
•
ILOAD = Load Current
RDSON_PFET = Drain to source resistance of PFET (high side) .
RIND = Inductor resistance
(1)
Out Of Regulation
When any of the Buck outputs are taken out of regulation (below 85% of the output level) the device will start a
shutdown sequence and all other ouputs will switch off normally. The device will restart when the forced out-ofregulation condition is removed.
20
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Device Operating Modes
STARTUP SEQUENCE
The startup mode of the LM10502 will depend on the input voltage. Once VIN reaches the UVLO threshold, there
is a 15 msec delay before the LM10502 determines how to set up the buck regulators. If VIN is greater than 3.6V,
the bucks will start up as the standard regulators. The 2 buck regulators are staggered during startup to avoid
large inrush currents. There is a fixed delay of 2 msec between the startup of each regulator.
The Startup Sequence will be:
1. 15 msec (±30%) delay after VIN above UVLO
2. LDO → 3V
3. 2 msec delay
4. Buck 1 → 1.8V
5. 2 msec delay
6. Buck 2 → 1.2V
5.75V
5.65V
~3.2V
VCOMP_ FALL
2.6V
~2.25V
2.9V
VIN
0V
BG/BIAS
UVLO internal status
15 ms
15 ms
3.0V
3.0V
LDO Vout
1.8V
1.8V
2ms
2 ms
Buck1 Vout
1.2V
1.2V
2 ms
2ms
Buck2 Vout
IRQ (LDO
driving VIN_IO)
OVLO
internal status
UVLO
STARTUP
OVLO
STARTUP
UVLO
Figure 23. Operating Modes
POWER-ON DEFAULT AND DEVICE ENABLE
The device is always enabled and the LDO is always on, unless outside of operating voltage range. There is no
LM10502 Enable Pin. Once VIN reaches a minimum required input Voltage the power-up sequence will be
started automatically and the startup sequence will be initiated. Once the device is started, the output voltage of
the Bucks can be individually disabled by accessing their corresponding BKEN register bits (BUCK CONTROL).
RESET: PIN FUNCTION
The RESET pin is internally pulled high. If the reset pin is pulled low, the device will perform a complete reset of
all the registers to their default states. This means that all of the voltage settings on the regulators will go back to
their default states.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
21
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
UNDERVOLTAGE LOCKOUT (UVLO)
The VIN voltage is monitored for a supply under voltage condition, for which the operation of the device can not
be ensured. The part will automatically disable the bucks. To prevent unstable operation, the undervoltage
lockout (UVLO) has a hysteresis window of about 300 mV. An under voltage lock out (UVLO) will force the
device into the reset state, all internal registers are reset. Once the supply voltage is above the UVLO hysteresis,
the device will initiate a power-up sequence and then enter the active state.
The LDO and the Comparator will remain functional past the UVLO threshold until VIN reaches approximately
2.25V.
OVERVOLTAGE LOCKOUT (OVLO)
The VIN voltage is monitored for a supply over voltage condition, for which the operation of the device cannot be
ensured. The purpose of overvoltage lockout (OVLO) is to protect the part and all other consumers connected to
the PMU outputs from any damage and malfunction. Once VIN rises over 5.7V all the Bucks, and LDO will be
disabled automatically. To prevent unstable operation, the OVLO has a hysteresis window of about 100 mV. An
OVLO will force the device into the reset state; all internal registers are reset. Once the supply voltage is below
the OVLO hysteresis, the device will initiate a power-up sequence, and then enter the active state. Operating
maximum input voltage at which parameters are ensured is 5.5V. Absolute maximum of the device is 6.0V.
DEVICE STATUS, INTERRUPT ENABLE
The LM10502 family of parts has 2 interrupt registers, INTERRUPT ENABLE and INTERRUPT STATUS. These
registers can be read via the serial interface. The interrupts are not latched to the register and will always
represent the current state and will not be cleared on a read.
If interrupt condition is detected, then corresponding bit in the INTERRUPT STATUS register (0x0D) is set to '1',
and Interrupt output is asserted. There are 4 interrupt generating conditions:
• Buck 2 output is over flag level (90% when rising, 85% when falling)
• Buck 1 output is over flag level (90% when rising, 85% when falling)
• LDO is over flag level (90% when rising, 85% when falling
• Comparator input voltage crosses over selected threshold
Reading the interrupt register will not release IRQ output. Interrupt generation conditions can be individually
enabled or disabled by writing respective bits in INTERRUPT ENABLE register (0x0C) to '1' or '0'.
THERMAL SHUTDOWN (TSD)
The temperature of the silicon die is monitored for an over-temperature condition, for which the operation of the
device can not be ensured. The part will automatically be disabled if the temperature is too high. The thermal
shutdown (TSD) will force the device into the reset state. In reset, all circuitry is disabled. To prevent unstable
operation, the TSD has a hysteresis window of about 20°C. Once the temperature has decreased below the TSD
hysteresis, the device will initiate a POWERUP sequence and then enter the active state. In the active state, the
part will start up as if for the first time, all registers will be in their default state.
COMPARATOR
The general-purpose comparator on the LM10502 takes its inputs from the VCOMP pin, which may be
connected according to user preferences and an internal threshold level is programmed by the user. The
threshold level is programmable between 2.0 and 4.0V with a step of 31mV and a default value of 2.794V. The
output of the comparator is the IRQ pin which polarity can be changed using Register 0x0E bit 0. If
Interrupt_polarity = 0 → Active low (default) is selected, then the output is low if VCOMP value is greater than the
threshold level. The output is high if the VCOMP value is less than the threshold level. If Interrupt_polarity=1→
Active high is selected then the output is high if VCOMP value is greater than the threshold level. The output is low
if the VCOMP value is less than the threshold level. There is some hysteresis when VCOMP transitions from high to
low, typically 60 mV. There is a control bit in register 0x0B, comparator control, that can double the hysteresis
value.
22
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
VTHRES
VCOMP
IRQ
+
IRQ
-
VCOMP
Delay due to
hysteresis
VTHRES
LDO
For stability the LDO needs to have an external capacitor connected to its output with a recommended minimum
value of 1µF. It is important to select the type of capacitor whose capacitance in no case (voltage
temperature,etc) will be outside the limits specified in the LDO electrical characteristics.
RECOMMENDATIONS FOR UNUSED FUNCTIONS AND PINS
If any function is not used in the end application, then the following recommendations for tying off the associated
pins on the circuit boards should be used.
FUNCTION
PIN
IF UNUSED
BUCK 1
VIN_B1
CONNECT TO VIN
SW_B1
CONNECT TO VIN
FB_B1
CONNECT TO GND
VIN_B2
CONNECT TO VIN
SW_B2
CONNECT TO VIN
FB_B2
CONNECT TO GND
SPI_CS
CONNECT TO VIN_IO
SPI_DI
CONNECT TO GND
SPI_DO
CONNECT TO GND
SPI_CLK
CONNECT TO GND
BUCK 2
SPI
LDO_VIN
CONNECT TO GND
RESET
CONNECT TO VIN_IO
COMPARATOR
VCOMP
CONNECT TO VIN
IRQ
LEAVE OPEN
External Components Selection
All two switchers require an input capacitor and an output inductor-capacitor filter. These components are critical
to the performance of the device. All two switchers are internally compensated and do not require external
components to achieve stable operation. The output voltages of the bucks can be programmed through the SPI
pins.
OUTPUT INDUCTORS & CAPACITORS SELECTION
There are several design considerations related to the selection of output inductors and capacitors:
• Load transient response
• Stability
• Efficiency
• Output ripple voltage
• Over current ruggedness
The device has been optimized for use with nominal LC values as shown in the Typical Application Circuit .
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
23
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
INDUCTOR SELECTION
The recommended inductor values are shown in Application Diagram Typical Application Diagram. It is important
to ensure the inductor core does not saturate during any foreseeable operational situation. The inductor should
be rated to handle the peak load current plus the ripple current:
Care should be taken when reviewing the different saturation current ratings that are specified by different
manufacturers. Saturation current ratings are typically specified at 25°C, so ratings at maximum ambient
temperature of the application should be requested from the manufacturer.
IL(MAX) = ILOAD(MAX) + 'IRIPPLE
= ILOAD(MAX) +
D x (VIN - VOUT)
2 x L x FS
D x (VIN - VOUT)
~ ILOAD(MAX) +
(A typ.),
~
2 x 2.2 x 2.0
D = VOUT , FS = 2 MHz, L = 2.2 PH
VIN
(2)
There are two methods to choose the inductor saturation current rating:
Recommended Method for Inductor Selection:
The best way to ensure the inductor does not saturate is to choose an inductor that has saturation current rating
greater than the maximum device current limit, as specified in the Electrical Characteristics tables. In this case
the device will prevent inductor saturation by going into current limit before the saturation level is reached.
Alternate Method for Inductor Selection:
If the recommended approach cannot be used care must be taken to ensure that the saturation current is greater
than the peak inductor current:
ISAT > ILPEAK
IRIPPLE
ILPEAK = IOUTMAX +
2
D x (VIN ± VOUT)
IRIPPLE =
L x FS
VOUT
D=
VIN x EFF
•
•
•
•
•
•
•
•
•
•
ISAT: Inductor saturation current at operating temperature
ILPEAK: Peak inductor current during worst case conditions
IOUTMAX: Maximum average inductor current
IRIPPLE: Peak-to-Peak inductor current
VOUT: Output voltage
VIN: Input voltage
L: Inductor value in Henries at IOUTMAX
F: Switching frequency, Hertz
D: Estimated duty factor
EFF: Estimated power supply efficiency
(3)
ISAT may not be exceeded during any operation, including transients, startup, high temperature, worst-case
conditions, etc.
Suggested Inductors and Their Suppliers
The designer should choose the inductors that best match the system requirements. A very wide range of
inductors are available as regarding physical size, height, maximum current (thermally limited, and inductance
loss limited), series resistance, maximum operating frequency, losses, etc. In general, smaller physical size
inductors will have higher series resistance (DCR) and implicitly lower overall efficiency is achieved. Very lowprofile inductors may have even higher series resistance. The designer should try to find the best compromise
between system performance and cost.
24
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Table 2. Recommended Inductors
Value
Manufacturer
Part Number
DCR
Current
Package
2.2 µH
Murata
LQH55PN2R2NR0L
31 mΩ
2.5A
2220
2.2 µH
TDK
NLC565050T-2R2K-PF
60 mΩ
1.3A
2220
2.2 µH
Murata
LQM2MPN2R2NG0
110 mΩ
1.2A
806
OUTPUT AND INPUT CAPACITORS CHARACTERISTICS
CAP VALUE (% of NOMINAL 1 PF)
Special attention should be paid when selecting these components. As shown in the following figure, the DC bias
of these capacitors can result in a capacitance value that falls below the minimum value given in the
recommended capacitor specifications table. Note that the graph shows the capacitance out of spec for the 0402
case size capacitor at higher bias voltages. It is therefore recommended that the capacitor manufacturers’
specifications for the nominal value capacitor are consulted for all conditions, as some capacitor sizes (e.g.,
0402) may not be suitable in the actual application.
0603, 10V, X5R
100
80
60
0402, 6.3V, X5R
40
20
0
1.0
2.0
3.0
4.0
5.0
DC BIAS (V)
Figure 24. Typical Variation in Capacitance vs.
DC Bias
The ceramic capacitor’s capacitance can vary with temperature. The capacitor type X7R, which operates over a
temperature range of −55°C to +125°C, will only vary the capacitance to within ±15%. The capacitor type X5R
has a similar tolerance over a reduced temperature range of −55°C to +85°C. Many large value ceramic
capacitors, larger than 1µF are manufactured with Z5U or Y5V temperature characteristics. Their capacitance
can drop by more than 50% as the temperature varies from 25°C to 85°C. Therefore X7R is recommended over
Z5U and Y5V in applications where the ambient temperature will change significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 0.47 µF to 44 µF range. Another
important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum capacitor with an ESR value within the stable range, it
would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the
same ESR value. It should also be noted that the ESR of a typical tantalum will increase about 2:1 as the
temperature goes from 25°C down to −40°C, so some guard band must be allowed.
Output Capacitor Selection
The output capacitor of a switching converter absorbs the AC ripple current from the inductor and provides the
initial response to a load transient. The ripple voltage at the output of the converter is the product of the ripple
current flowing through the output capacitor and the impedance of the capacitor. The impedance of the capacitor
can be dominated by capacitive, resistive, or inductive elements within the capacitor, depending on the frequency
of the ripple current. Ceramic capacitors have very low ESR and remain capacitive up to high frequencies. Their
inductive component can usually be neglected at the frequency ranges at which the switcher operates.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
25
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
COUT
L
ESR
SW1&2
VOUT1&2
OUTPUT
CAPACITOR
The output-filter capacitor smooths out the current flow from the inductor to the load and helps maintain a steady
output voltage during transient load changes. It also reduces output voltage ripple. These capacitors must be
selected with sufficient capacitance and low enough ESR to perform these functions.
Note that the output voltage ripple increases with the inductor current ripple and the Equivalent Series
Resistance of the output capacitor (ESRCOUT). Also note that the actual value of the capacitor’s ESRCOUT is
frequency and temperature dependent, as specified by its manufacturer. The ESR should be calculated at the
applicable switching frequency and ambient temperature.
D x (VIN - VOUT)
V
üIRIPPLE
and D = OUT
where üIRIPPLE =
2 x L x FS
8 x FS x COUT
VIN
VOUT-RIPPLE-PP =
Output ripple can be estimated from the vector sum of the reactive (capacitance) voltage component and the real
(ESR) voltage component of the output capacitor where:
VOUT-RIPPLE-PP =
2
V
2
ROUT
+V
(4)
COUT
where:
VROUT = IRIPPLE x ESRCOUT and VCOUT =
•
•
•
IRIPPLE
8 x FS x COUT
VOUT-RIPPLE-PP: estimated output ripple,
VROUT: estimated real output ripple,
VCOUT: estimated reactive output ripple.
(5)
The device is designed to be used with ceramic capacitors on the outputs of the buck regulators. The
recommended dielectric type of these capacitors is X5R, X7R, or of comparable material to maintain proper
tolerances over voltage and temperature. The recommended value for the output capacitors is 22 μF, 6.3V with
an ESR of 2mΩ or less. The output capacitors need to be mounted as close as possible to the output/ground
pins of the device.
Table 3. Recommended Output Capacitors
26
Model
Type
Vendor
Vendor
Voltage Rating
Case Size
08056D226MAT2A
Ceramic, X5R
AVX Corporation
6.3V
0805, (2012)
C0805L226M9PACTU
Ceramic, X5R
Kemet
6.3V
0805, (2012)
ECJ-2FB0J226M
Ceramic, X5R
Panasonic - ECG
6.3V
0805, (2012)
JMK212BJ226MG-T
Ceramic, X5R
Taiyo Yuden
6.3V
0603, (1608)
C2012X5R0J226M
Ceramic, X5R
TDK Corporation
6.3V
0603, (1608)
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
Input Capacitor Selection
There are 2 buck regulators in the LM10502 device. Each of these buck regulators has its own input capacitor
which should be located as close as possible to their corresponding VIN_Bx and GND_Bx pins, where x
designates buck 1or 2. The 2 buck regulators operate at 120° out of phase, which means that they switch on at
equally spaced intervals, in order to reduce the input power rail ripple. It is recommended to connect all the
supply/ground pins of the buck regulators, VIN_Bx to two solid internal planes located under the device. In this
way, the 2 input capacitors work together and further reduce the input current ripple. A larger tantalum capacitor
can also be located in the proximity of the device.
The input capacitor supplies the AC switching current drawn from the switching action of the internal power
FETs. The input current of a buck converter is discontinuous, so the ripple current supplied by the input capacitor
is large. The input capacitor must be rated to handle both the RMS current and the dissipated power.
The input capacitor must be rated to handle this current:
VOUT (VIN - VOUT)
VIN
IRMS_CIN = IOUT
(6)
The power dissipated in the input capacitor is given by:
PD_CIN = I2RMS_CIN x RESR_CIN
(7)
The device is designed to be used with ceramic capacitors on the inputs of the buck regulators. The
recommended dielectric type of these capacitors is X5R, X7R, or of comparable material to maintain proper
tolerances over voltage and temperature. The minimum recommended value for the input capacitor is 10 µF with
an ESR of 10 mΩ or less. The input capacitors need to be mounted as close as possible to the power/ground
input pins of the device.
The input power source supplies the average current continuously. During the PFET switch on-time, however,
the demanded di/dt is higher than can be typically supplied by the input power source. This delta is supplied by
the input capacitor.
A simplified “worst case” assumption is that all of the PFET current is supplied by the input capacitor. This will
result in conservative estimates of input ripple voltage and capacitor RMS current.
Input ripple voltage is estimated as follows:
VPPIN =
IOUT x D
+ IOUT x ESRCIN
CIN x FS
where:
•
•
•
•
VPPIN: estimated peak-to-peak input ripple voltage,
IOUT: Output Current
CIN: Input capacitor value
ESRCIN: input capacitor ESR.
(8)
This capacitor is exposed to significant RMS current, so it is important to select a capacitor with an adequate
RMS current rating. Capacitor RMS current estimated as follows:
©
•
I2RIPPLE
12
§
©
IRMSCIN = D x §I2OUT +
IRMSCIN: estimated input capacitor RMS current.
(9)
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
27
LM10502
SNVS884B – AUGUST 2012 – REVISED MAY 2013
www.ti.com
PCB Layout Considerations
PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance
of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss
in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability.
Good layout can be implemented by following a few simple design rules.
S
CIN
L
D
N
COUT
GND
LOOP2
G
VIN
CONTROL
LOOP1
VOUT
P
D
SW VIN
G
S
LM10502
Figure 25. Schematic of LM10502 Highlighting Layout Sensitive Nodes
1. Minimize area of switched current loops. In a buck regulator there are two loops where currents are switched
rapidly. The first loop starts from the CIN input capacitor, to the regulator VIN pin, to the regulator SW pin, to
the inductor then out to the output capacitor COUT and load. The second loop starts from the output capacitor
ground, to the regulator GND pins, to the inductor and then out to COUT and the load (see figure above). To
minimize both loop areas the input capacitor should be placed as close as possible to the VIN pin. Grounding
for both the input and output capacitors should consist of a small localized top side plane that connects to
GND. The inductor should be placed as close as possible to the SW pin and output capacitor.
2. Minimize the copper area of the switch node. The SW pins should be directly connected with a trace that
runs on top side directly to the inductor. To minimize IR losses this trace should be as short as possible and
with a sufficient width. However, a trace that is wider than 100 mils will increase the copper area and cause
too much capacitive loading on the SW pin. The inductors should be placed as close as possible to the SW
pins to further minimize the copper area of the switch node.
3. Have a single point ground for all device analog grounds. The ground connections for the feedback
components should be connected together then routed to the GND pin of the device. This prevents any
switched or load currents from flowing in the analog ground plane. If not properly handled, poor grounding
can result in degraded load regulation or erratic switching behavior.
4. Minimize trace length to the FB pin. The feedback trace should be routed away from the SW pin and inductor
to avoid contaminating the feedback signal with switch noise.
5. Make input and output bus connections as wide as possible. This reduces any voltage drops on the input or
output of the converter and can improve efficiency. If voltage accuracy at the load is important make sure
feedback voltage sense is made at the load. Doing so will correct for voltage drops at the load and provide
the best output accuracy.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
28
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
LM10502
www.ti.com
SNVS884B – AUGUST 2012 – REVISED MAY 2013
REVISION HISTORY
Changes from Original (March 2013) to Revision A
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 28
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: LM10502
29
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM10502TLE/NOPB
ACTIVE
DSBGA
YZR
25
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
0 to 0
V076
LM10502TLX/NOPB
ACTIVE
DSBGA
YZR
25
3000
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-30 to 125
V076
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of