LM1875
www.ti.com
SNAS524A – MAY 2004 – REVISED MAY 2004
LM1875 20W Audio Power Amplifier
Check for Samples: LM1875
FEATURES
DESCRIPTION
•
•
•
•
•
The LM1875 is a monolithic power amplifier offering
very low distortion and high quality performance for
consumer audio applications.
1
2
•
•
•
•
•
•
Up to 30 Watts Output Power
AVO Typically 90 dB
Low Distortion: 0.015%, 1 kHz, 20 W
Wide Power Bandwidth: 70 kHz
Protection for AC and DC Short Circuits to
Ground
Thermal Protection with Parole Circuit
High Current Capability: 4A
Wide Supply Range 16V-60V
Internal Output Protection Diodes
94 dB Ripple Rejection
Plastic Power Package TO-220
APPLICATIONS
•
•
•
•
•
High Performance Audio Systems
Bridge Amplifiers
Stereo Phonographs
Servo Amplifiers
Instrument Systems
The LM1875 delivers 20 watts into a 4Ω or 8Ω load
on ±25V supplies. Using an 8Ω load and ±30V
supplies, over 30 watts of power may be delivered.
The amplifier is designed to operate with a minimum
of external components. Device overload protection
consists of both internal current limit and thermal
shutdown.
The LM1875 design takes advantage of advanced
circuit techniques and processing to achieve
extremely low distortion levels even at high output
power levels. Other outstanding features include high
gain, fast slew rate and a wide power bandwidth,
large output voltage swing, high current capability,
and a very wide supply range. The amplifier is
internally compensated and stable for gains of 10 or
greater.
Connection Diagram
Figure 1. NDH0005D, KC0005A,
NEB0005E, NEB0005B,
Front View
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004, Texas Instruments Incorporated
LM1875
SNAS524A – MAY 2004 – REVISED MAY 2004
www.ti.com
Typical Applications
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)
Supply Voltage
60V
−VEE to VCC
Input Voltage
−65°C to + 150°C
Storage Temperature
Junction Temperature
150°C
(Soldering, 10 seconds)
Lead Temperature
(1)
2
260°C
θJC
3°C
θJA
73°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
LM1875
www.ti.com
SNAS524A – MAY 2004 – REVISED MAY 2004
Electrical Characteristics
VCC=+25V, −VEE=−25V, TAMBIENT=25°C, RL=8Ω, AV=20 (26 dB), fo=1 kHz, unless otherwise specified.
Parameter
Conditions
Typical
Tested Limits
Units
100
mA
Supply Current
POUT=0W
70
Output Power (1)
THD=1%
25
THD (1)
POUT=20W, fo=1 kHz
0.015
POUT=20W, fo=20 kHz
0.05
POUT=20W, RL=4Ω, fo=1 kHz
0.022
POUT=20W, RL=4Ω, fo=20 kHz
0.07
0.6
%
±1
±15
mV
±0.2
±2
μA
0
±0.5
Offset Voltage
Input Bias Current
Input Offset Current
W
%
0.4
%
Gain-Bandwidth Product
fo=20 kHz
5.5
Open Loop Gain
DC
90
PSRR
VCC, 1 kHz, 1 Vrms
95
52
VEE, 1 kHz, 1 Vrms
83
52
Max Slew Rate
20W, 8Ω, 70 kHz BW
8
Current Limit
VOUT = VSUPPLY −10V
4
Equivalent Input Noise Voltage
RS=600Ω, CCIR
3
(1)
%
μA
MHz
dB
dB
dB
V/μs
3
A
μVrms
Assumes the use of a heat sink having a thermal resistance of 1°C/W and no insulator with an ambient temperature of 25°C. Because
the output limiting circuitry has a negative temperature coefficient, the maximum output power delivered to a 4Ω load may be slightly
reduced when the tab temperature exceeds 55°C.
Typical Applications For Single Supply Operation
Figure 2.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
3
LM1875
SNAS524A – MAY 2004 – REVISED MAY 2004
www.ti.com
Typical Performance Characteristics
THD vs Power Output
THD vs Frequency
Figure 3.
Figure 4.
Power Output vs Supply
Voltage
Supply Current vs Supply
Voltage
Figure 5.
Figure 6.
PSRR vs Frequency
Device Dissipation vs Ambient Temperature†
†φINTERFACE = 1°C/W.
See Application Hints.
Figure 7.
4
Figure 8.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
LM1875
www.ti.com
SNAS524A – MAY 2004 – REVISED MAY 2004
Typical Performance Characteristics (continued)
Power Dissipation vs Power Output
Power Dissipation vs Power Output
Figure 9.
Figure 10.
IOUT vs VOUT-Current Limit/
Safe Operating Area Boundary
Open Loop Gain and Phase vs Frequency
Figure 11.
Thermal shutdown with infinite heat sink
Thermal shutdown with 1°C/W heat sink
Figure 12.
Input Bias Current vs Supply Voltage
Figure 13.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
5
LM1875
SNAS524A – MAY 2004 – REVISED MAY 2004
www.ti.com
Schematic Diagram
6
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
LM1875
www.ti.com
SNAS524A – MAY 2004 – REVISED MAY 2004
APPLICATION HINTS
STABILITY
The LM1875 is designed to be stable when operated at a closed-loop gain of 10 or greater, but, as with any
other high-current amplifier, the LM1875 can be made to oscillate under certain conditions. These usually involve
printed circuit board layout or output/input coupling.
Proper layout of the printed circuit board is very important. While the LM1875 will be stable when installed in a
board similar to the ones shown in this data sheet, it is sometimes necessary to modify the layout somewhat to
suit the physical requirements of a particular application. When designing a different layout, it is important to
return the load ground, the output compensation ground, and the low level (feedback and input) grounds to the
circuit board ground point through separate paths. Otherwise, large currents flowing along a ground conductor
will generate voltages on the conductor which can effectively act as signals at the input, resulting in high
frequency oscillation or excessive distortion. It is advisable to keep the output compensation components and the
0.1 μF supply decoupling capacitors as close as possible to the LM1875 to reduce the effects of PCB trace
resistance and inductance. For the same reason, the ground return paths for these components should be as
short as possible.
Occasionally, current in the output leads (which function as antennas) can be coupled through the air to the
amplifier input, resulting in high-frequency oscillation. This normally happens when the source impedance is high
or the input leads are long. The problem can be eliminated by placing a small capacitor (on the order of 50 pF to
500 pF) across the circuit input.
Most power amplifiers do not drive highly capacitive loads well, and the LM1875 is no exception. If the output of
the LM1875 is connected directly to a capacitor with no series resistance, the square wave response will exhibit
ringing if the capacitance is greater than about 0.1 μF. The amplifier can typically drive load capacitances up to 2
μF or so without oscillating, but this is not recommended. If highly capacitive loads are expected, a resistor (at
least 1Ω) should be placed in series with the output of the LM1875. A method commonly employed to protect
amplifiers from low impedances at high frequencies is to couple to the load through a 10Ω resistor in parallel with
a 5 μH inductor.
DISTORTION
The preceding suggestions regarding circuit board grounding techniques will also help to prevent excessive
distortion levels in audio applications. For low THD, it is also necessary to keep the power supply traces and
wires separated from the traces and wires connected to the inputs of the LM1875. This prevents the power
supply currents, which are large and nonlinear, from inductively coupling to the LM1875 inputs. Power supply
wires should be twisted together and separated from the circuit board. Where these wires are soldered to the
board, they should be perpendicular to the plane of the board at least to a distance of a couple of inches. With a
proper physical layout, THD levels at 20 kHz with 10W output to an 8Ω load should be less than 0.05%, and less
than 0.02% at 1 kHz.
CURRENT LIMIT AND SAFE OPERATING AREA (SOA) PROTECTION
A power amplifier's output transistors can be damaged by excessive applied voltage, current flow, or power
dissipation. The voltage applied to the amplifier is limited by the design of the external power supply, while the
maximum current passed by the output devices is usually limited by internal circuitry to some fixed value. Shortterm power dissipation is usually not limited in monolithic audio power amplifiers, and this can be a problem
when driving reactive loads, which may draw large currents while high voltages appear on the output transistors.
The LM1875 not only limits current to around 4A, but also reduces the value of the limit current when an output
transistor has a high voltage across it.
When driving nonlinear reactive loads such as motors or loudspeakers with built-in protection relays, there is a
possibility that an amplifier output will be connected to a load whose terminal voltage may attempt to swing
beyond the power supply voltages applied to the amplifier. This can cause degradation of the output transistors
or catastrophic failure of the whole circuit. The standard protection for this type of failure mechanism is a pair of
diodes connected between the output of the amplifier and the supply rails. These are part of the internal circuitry
of the LM1875, and needn't be added externally when standard reactive loads are driven.
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
7
LM1875
SNAS524A – MAY 2004 – REVISED MAY 2004
www.ti.com
THERMAL PROTECTION
The LM1875 has a sophisticated thermal protection scheme to prevent long-term thermal stress to the device.
When the temperature on the die reaches 170°C, the LM1875 shuts down. It starts operating again when the die
temperature drops to about 145°C, but if the temperature again begins to rise, shutdown will occur at only 150°C.
Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but
a sustained fault will limit the maximum die temperature to a lower value. This greatly reduces the stresses
imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions.
Since the die temperature is directly dependent upon the heat sink, the heat sink should be chosen for thermal
resistance low enough that thermal shutdown will not be reached during normal operation. Using the best heat
sink possible within the cost and space constraints of the system will improve the long-term reliability of any
power semiconductor device.
POWER DISSIPATION AND HEAT SINKING
The LM1875 must always be operated with a heat sink, even when it is not required to drive a load. The
maximum idling current of the device is 100 mA, so that on a 60V power supply an unloaded LM1875 must
dissipate 6W of power. The 54°C/W junction-to-ambient thermal resistance of a TO-220 package would cause
the die temperature to rise 324°C above ambient, so the thermal protection circuitry will shut the amplifier down if
operation without a heat sink is attempted.
In order to determine the appropriate heat sink for a given application, the power dissipation of the LM1875 in
that application must be known. When the load is resistive, the maximum average power that the IC will be
required to dissipate is approximately:
where
•
•
•
VS is the total power supply voltage across the LM1875
RL is the load resistance
PQ is the quiescent power dissipation of the amplifier
The above equation is only an approximation which assumes an “ideal” class B output stage and constant power
dissipation in all other parts of the circuit. The curves of “Power Dissipation vs Power Output” give a better
representation of the behavior of the LM1875 with various power supply voltages and resistive loads. As an
example, if the LM1875 is operated on a 50V power supply with a resistive load of 8Ω, it can develop up to 19W
of internal power dissipation. If the die temperature is to remain below 150°C for ambient temperatures up to
70°C, the total junction-to-ambient thermal resistance must be less than
Using θJC=2°C/W, the sum of the case-to-heat-sink interface thermal resistance and the heat-sink-to-ambient
thermal resistance must be less than 2.2°C/W. The case-to-heat-sink thermal resistance of the TO-220 package
varies with the mounting method used. A metal-to-metal interface will be about 1°C/W if lubricated, and about
1.2°C/W if dry.
If a mica insulator is used, the thermal resistance will be about 1.6°C/W lubricated and 3.4°C/W dry. For this
example, we assume a lubricated mica insulator between the LM1875 and the heat sink. The heat sink thermal
resistance must then be less than
4.2°C/W−2°C/W−1.6°C/W=0.6°C/W.
This is a rather large heat sink and may not be practical in some applications. If a smaller heat sink is required
for reasons of size or cost, there are two alternatives. [EM00001]The maximum ambient operating temperature
can be reduced to 50°C (122°F), resulting in a 1.6°C/W heat sink, or the heat sink can be isolated from the
chassis so the mica washer is not needed. This will change the required heat sink to a 1.2°C/W unit if the caseto-heat-sink interface is lubricated.
8
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
LM1875
www.ti.com
SNAS524A – MAY 2004 – REVISED MAY 2004
NOTE
When using a single supply, maximum transfer of heat away from the LM1875 can be
achieved by mounting the device directly to the heat sink (tab is at ground potential); this
avoids the use of a mica or other type insulator.
The thermal requirements can become more difficult when an amplifier is driving a reactive load. For a given
magnitude of load impedance, a higher degree of reactance will cause a higher level of power dissipation within
the amplifier. As a general rule, the power dissipation of an amplifier driving a 60° reactive load (usually
considered to be a worst-case loudspeaker load) will be roughly that of the same amplifier driving the resistive
part of that load. For example, a loudspeaker may at some frequency have an impedance with a magnitude of
8Ω and a phase angle of 60°. The real part of this load will then be 4Ω, and the amplifier power dissipation will
roughly follow the curve of power dissipation with a 4Ω load.
Component Layouts
Figure 14. Split Supply
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
9
LM1875
SNAS524A – MAY 2004 – REVISED MAY 2004
www.ti.com
Figure 15. Single Supply
10
Submit Documentation Feedback
Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM1875
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM1875T
ACTIVE
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LB02
ACTIVE
TO-220
NEB
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LB03
ACTIVE
TO-220
NDH
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LB05
ACTIVE
TO-220
NEB
5
45
Non-RoHS
& Green
Call TI
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LF02
ACTIVE
TO-220
NEB
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LF03
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/LF05
ACTIVE
TO-220
NEB
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
0 to 70
LM1875T
LM1875T/NOPB
ACTIVE
TO-220
NDH
5
45
RoHS & Green
SN
Level-1-NA-UNLIM
0 to 70
LM1875T
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of