LM25017
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
LM25017 48-V, 650-mA Constant On-Time Synchronous Buck/Fly-Buck™ Regulator
1 Features
3 Description
•
•
The LM25017 device is a 48-V, 650-mA synchronous
step-down regulator with integrated high-side and
low-side MOSFETs. The constant on-time (COT)
control scheme employed in the LM25017 device
requires no loop compensation, provides excellent
transient response, and enables very high step-down
ratios. The on-time varies inversely with the input
voltage resulting in nearly constant frequency over the
input voltage range. A high voltage startup regulator
provides bias power for internal operation of the IC
and for integrated gate drivers.
A peak current limit circuit protects against overload
conditions. The undervoltage lockout (UVLO) circuit
allows the input undervoltage threshold and
hysteresis to be independently programmed. Other
protection features include thermal shutdown and bias
supply undervoltage lockout (VCC UVLO).
2 Applications
•
•
•
•
The LM25017 device is available in WSON-8 and
HSOP-8 plastic packages.
Industrial equipment
Smart power meters
Telecommunication systems
Isolated bias supply (Fly-Buck™)
Device Information
PART NUMBER
LM25017
CIN
2
+
4
RUV2
BST
VIN
SW
RON
BODY SIZE (NOM)
HSOP (8)
4.89 mm x 3.90 mm
WSON (8)
4.00 mm x 4.00 mm
3
VCC
UVLO
FB
RUV1
7
+
CBST
8
L1
VOUT
CVCC
RON
SD
PACKAGE
LM25017
7.5 V - 48 V
VIN
RTN
+
•
•
•
•
•
•
•
•
•
•
•
•
•
Wide 7.5-V to 48-V input range
Integrated 650-mA high-side and
low-side switches
No schottky diode required
Constant on-time control
No loop compensation required
Ultra-fast transient response
Nearly constant operating frequency
Intelligent peak current limit
Adjustable output voltage from 1.225 V
Precision 2% feedback reference
Frequency adjustable to 1 MHz
Adjustable undervoltage lockout (UVLO)
Remote shutdown
Thermal shutdown
Create a custom design using the LM25017 with
the WEBENCH® power designer
6
RFB2
5
1
RC
+
RFB1
COUT
Typical Application Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................4
6 Specifications.................................................................. 5
6.1 Absolute Maximum Ratings........................................ 5
6.2 ESD Ratings............................................................... 5
6.3 Recommended Operating Conditions.........................5
6.4 Thermal Information....................................................5
6.5 Electrical Characteristics.............................................6
6.6 Switching Characteristics............................................6
6.7 Typical Characteristics................................................ 7
7 Detailed Description........................................................9
7.1 Overview..................................................................... 9
7.2 Functional Block Diagram........................................... 9
7.3 Feature Description.....................................................9
7.4 Device Functional Modes..........................................14
8 Application and Implementation.................................. 15
8.1 Application Information............................................. 15
8.2 Typical Applications.................................................. 15
9 Power Supply Recommendations................................26
10 Layout...........................................................................27
10.1 Layout Guidelines................................................... 27
10.2 Layout Example...................................................... 27
11 Device and Documentation Support..........................28
11.1 Device Support........................................................28
11.2 Documentation Support.......................................... 28
11.3 Receiving Notification of Documentation Updates.. 28
11.4 Support Resources................................................. 28
11.5 Trademarks............................................................. 28
11.6 Electrostatic Discharge Caution.............................. 28
11.7 Glossary.................................................................. 29
12 Mechanical, Packaging, and Orderable
Information.................................................................... 29
4 Revision History
Changes from Revision E (November 2017) to Revision F (May 2021)
Page
• Added "Synchronous Fly-Buck" to the title......................................................................................................... 1
• Hyperlinked Applications bullets......................................................................................................................... 1
• Updated the numbering format for tables, figures, and cross-references throughout the document. ................1
Changes from Revision D (December 2014) to Revision E (November 2017)
Page
• Added links for WEBENCH and top nav icon for TI Designs..............................................................................1
• Deleted lead temperature and related footnote from Abs Max table.................................................................. 5
• Changed 14 V to 13 V in VCC Regulator section.............................................................................................. 10
• Changed 8 to 4 on equation in Input Capacitor section....................................................................................17
• Changed 0.34 μF to 0.68 μF in Input Capacitor section................................................................................... 17
Changes from Revision C (December 2013) to Revision D (October 2014)
Page
• Added Pin Configuration and Functions section, ESD Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ............................................................................................................................................................... 1
• Changed VIN voltage in Typical Application ...................................................................................................... 1
• Changed max operating junction temperature in Recommended Operating Conditions table. .........................5
• Updated Thermal Information table with package designators. .........................................................................5
• Changed Soft-Start Circuit graphic................................................................................................................... 13
• Changed Frequency Selection section, Inductor Selection section, Output Capacitor section, Input Capacitor
section, and UVLO Resistors section............................................................................................................... 16
Changes from Revision B (December 2013) to Revision C (December 2013)
Page
• Added Thermal Parameters................................................................................................................................5
2
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
Changes from Revision A (September 2013) to Revision B (December 2013)
Page
• Changed formatting throughout document to TI standard.................................................................................. 1
• Changed minimum input voltage from 9 V to 7.5 V in Typical Application diagram............................................1
• Changed minimum input voltage from 9 V to 7.5 V in Pin Descriptions ............................................................ 4
• Added Maximum Junction Temperature............................................................................................................. 5
• Changed minimum input voltage from 9 V to 7.5 V in Recommended Operating Conditions ........................... 5
Changes from Revision * (December 2012) to Revision A (September 2013)
Page
• Added SW to RTN (100-ns transient) to Absolute Maximum Ratings ............................................................... 5
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
3
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
5 Pin Configuration and Functions
RTN
1
VIN
2
UVLO
3
RON
4
SO
PowePAD-8
Exp Pad
8
SW
7
BST
6
VCC
5
FB
Figure 5-1. 8-Pin HSOP DDA Package Top View
RTN
1
VIN
2
UVLO
3
RON
4
8 SW
WSON-8
Exp Pad
7 BST
6 VCC
5 FB
Figure 5-2. 8-Pin WSON NGU Package Top View
Table 5-1. Pin Functions
PIN
NO.
4
NAME
I/O
1
RTN
—
2
VIN
I
DESCRIPTION
APPLICATION INFORMATION
Ground
Ground connection of the integrated circuit.
Input Voltage
Operating input range is 7.5 V to 48 V.
3
UVLO
I
Input Pin of Undervoltage Comparator
Resistor divider from VIN to UVLO to GND programs
the undervoltage detection threshold. An internal current
source is enabled when UVLO is above 1.225 V to
provide hysteresis. When UVLO pin is pulled below 0.66
V externally, the regulator is in shutdown mode.
4
RON
I
On-Time Control
A resistor between this pin and VIN sets the buck switch
on-time as a function of VIN. Minimum recommended
on-time is 100 ns at max input voltage.
5
FB
I
Feedback
This pin is connected to the inverting input of the internal
regulation comparator. The regulation level is 1.225 V.
6
VCC
O
Output from the Internal High Voltage
Series Pass Regulator. Regulated at 7.6 V
The internal VCC regulator provides bias supply for
the gate drivers and other internal circuitry. A 1.0-μF
decoupling capacitor is recommended.
7
BST
I
Bootstrap Capacitor
An external capacitor is required between the BST and
SW pins (0.01-μF ceramic). The BST pin capacitor is
charged by the VCC regulator through an internal diode
when the SW pin is low.
8
SW
O
Switching Node
Power switching node. Connect to the output inductor
and bootstrap capacitor.
—
EP
—
Exposed Pad
Exposed pad must be connected to the RTN pin. Solder
to the system ground plane on application board for
reduced thermal resistance.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
6 Specifications
6.1 Absolute Maximum Ratings
MIN(1) (2)
MAX
UNIT
VIN, UVLO to RTN
–0.3
53
V
SW to RTN
–1.5
VIN +0.3
V
–5
VIN +0.3
V
BST to VCC
53
V
BST to SW
13
V
SW to RTN (100-ns transient)
RON to RTN
–0.3
53
V
VCC to RTN
–0.3
13
V
FB to RTN
–0.3
Maximum junction temperature(3)
Storage temperature, Tstg
(1)
(2)
(3)
–55
5
V
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
High junction temperatures degrade operating lifetimes. Operating lifetime is de-rated for junction temperatures greater than 125°C.
The RTN pin is the GND reference electrically connected to the substrate.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC
V(ESD)
(1)
(2)
Electrostatic discharge
JS-001(1)
UNIT
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101(2)
V
±750
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
UNIT
VIN voltage
7.5
48
V
Operating junction temperature(2)
–40
125
°C
(1)
(2)
Recommended Operating Conditions are conditions under the device is intended to be functional. For specifications and test
conditions, see Section 6.5 .
High junction temperatures degrade operating lifetimes. Operating lifetime is de-rated for junction temperatures greater than 125°C.
6.4 Thermal Information
LM25017
THERMAL
METRICS(1)
NGU
DDA
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
41.3
41.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
34.7
37.3
°C/W
RθJB
Junction-to-board thermal resistance
19.1
30.6
°C/W
ψJT
Junction-to-top thermal characteristic parameter
0.3
6.7
°C/W
ψJB
Junction-to-board thermal characteristic parameter
19.2
24.4
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
3.2
2.4
°C/W
(1)
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953).
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
5
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
6.5 Electrical Characteristics
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over –40°C to 125°C junction temperature
range, unless otherwise stated. VIN = 48 V unless otherwise stated. VIN = 48 V unless otherwise stated. See (1).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
6.25
7.6
8.55
UNIT
VCC SUPPLY
VCC Reg
VCC Regulator Output
VIN = 48 V, ICC = 20 mA
VCC Current Limit
VIN = 48 V(2)
26
VCC Undervoltage Lockout Voltage
(VCC increasing)
4.15
4.5
VCC Undervoltage Hysteresis
VCC Drop Out Voltage
V
mA
VIN = 9 V, ICC = 20 mA
4.9
V
300
mV
2.3
V
IIN Operating Current
Non-Switching, FB = 3 V
IIN Shutdown Current
UVLO = 0 V
1.75
50
225
mA
µA
ITEST = 200 mA, BST-SW = 7 V
0.8
1.8
Ω
0.45
1
Ω
3
3.6
V
SWITCH CHARACTERISTICS
Buck Switch RDS(ON)
Synchronous RDS(ON)
ITEST = 200 mA
Gate Drive UVLO
VBST – VSW Rising
2.4
Gate Drive UVLO Hysteresis
260
mV
CURRENT LIMIT
Current Limit Threshold
0.7
Current Limit Response Time
Time to Switch Off
OFF-Time Generator (Test 1)
OFF-Time Generator (Test 2)
1.02
1.3
A
150
ns
FB = 0.1 V, VIN = 48 V
12
µs
FB = 1.0 V, VIN = 48 V
2.5
µs
REGULATION AND OVERVOLTAGE COMPARATORS
FB Regulation Level
Internal Reference Trip Point for
Switch ON
FB Overvoltage Threshold
Trip Point for Switch OFF
1.2
1.225
FB Bias Current
1.25
V
1.62
V
60
nA
UNDERVOLTAGE SENSING FUNCTION
UV Threshold
UV Rising
UV Hysteresis Input Current
UV = 2.5 V
Remote Shutdown Threshold
Voltage at UVLO Falling
1.19
1.225
1.26
V
–10
–20
–29
µA
0.32
0.66
V
110
mV
165
°C
20
°C
Remote Shutdown Hysteresis
THERMAL SHUTDOWN
Tsd
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
(1)
(2)
All hot and cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying
statistical process control.
VCC provides self bias for the internal gate drive and control circuits. Device thermal limitations limit external loading.
6.6 Switching Characteristics
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over –40°C to 125°C junction temperature range
unless otherwise stated. VIN = 48 V unless otherwise stated.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ON-TIME GENERATOR
TON Test 1
VIN = 32 V, RON = 100 k
270
350
460
ns
TON Test 2
VIN = 48 V, RON = 100 k
188
250
336
ns
TON Test 4
VIN = 10 V, RON = 250 k
1880
3200
4425
ns
MINIMUM OFF-TIME
6
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over –40°C to 125°C junction temperature range
unless otherwise stated. VIN = 48 V unless otherwise stated.
PARAMETER
TEST CONDITIONS
Minimum Off-Timer
MIN
TYP
FB = 0 V
MAX
UNIT
144
ns
6.7 Typical Characteristics
8
100
7
95
5
VCC (V)
Efficiency (%)
6
90
85
4
3
80
2
VIN=13V
75
1
VIN=24V
Vout=10V, fsw=240 kHz
VIN=36V
VCCvsVIN
0
70
0
50
150
250
350
450
550
2
6
Load Current (mA)
8
10
12
14
VIN (V)
C010
C011
Figure 6-1. Efficiency at 200 kHz, 10 V
Figure 6-2. VCC vs VIN
8
8
7
VIN=48V
VIN=24V
VIN=48V
VIN=24V
7
6
6
ICC (mA)
5
VCC (V)
4
650
4
3
1 MHz
5
4
450 kHz
2
3
1
VIN=15V
0
2
0
10
20
30
40
50
60
8
9
10
ICC (mA)
11
12
13
14
VCC (V)
C012
C013
Figure 6-3. VCC vs ICC
Figure 6-4. ICC vs External VCC
20
Current Limit Off-Time (µs)
On-Time (ns)
10,000
1,000
100
RON=499KOhms
16
VIN=48V
VIN=36V
VIN=24V
VIN=14V
12
8
4
RON=250kOhms
RON=100kOhms
10
10
20
30
40
0
0.00
50
VIN (V)
0.25
0.50
0.75
1.00
1.25
VFB (V)
C014
Figure 6-5. TON vs VIN and RON
C015
Figure 6-6. TOFF (ILIM) vs VFB and VIN
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
7
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
1.84
120
UVLO=VIN, FB=3V
UVLO=0
100
Shutdown Current (µA)
Operating Current (mA)
1.80
1.76
1.72
1.68
80
60
40
1.64
20
1.60
0
0
10
20
30
40
50
0
10
VIN (V)
20
30
40
50
VIN (V)
C016
C017
Figure 6-7. IIN vs VIN (Operating, Non-Switching)
Figure 6-8. IIN vs VIN (Shutdown)
300
Frequency (kHz)
250
200
150
100
RON=499kOhms,
VOUT=10V
50
10
15
20
25
30
35
40
45
50
VIN (V)
C010
Figure 6-9. Switching Frequency vs VIN
8
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
7 Detailed Description
7.1 Overview
The LM25017 step-down switching regulator features all the functions needed to implement a low cost, efficient,
buck converter capable of supplying up to 650 mA to the load. This high voltage regulator contains 48-V,
N-channel buck and synchronous switches, is easy to implement, and is provided in thermally enhanced SO
PowerPAD-8 and WSON-8 packages. The regulator operation is based on a constant on-time control scheme
using an on-time inversely proportional to VIN. This control scheme does not require loop compensation. The
current limit is implemented with a forced off-time inversely proportional to VOUT. This scheme ensures short
circuit protection while providing minimum fold-back.
The LM25017 device can be applied in numerous applications to efficiently regulate down higher voltages. This
regulator is well suited for 12-V and 24-V rails. Protection features include: thermal shutdown, Undervoltage
Lockout (UVLO), minimum forced off-time, and an intelligent current limit.
7.2 Functional Block Diagram
LM25017
START-UP
REGULATOR
VIN
VCC
V UVLO
20 µA
4.5V
UVLO
THERMAL
SHUTDOWN
UVLO
1.225V
SD
VDD REG
BST
0.66V
SHUTDOWN
BG REF
VIN
DISABLE
ON/OFF
TIMERS
RON
1.225V
SW
COT CONTROL
LOGIC
FEEDBACK
FB
OVER-VOLTAGE
1.62V
CURRENT
LIMIT
ONE-SHOT
ILIM
COMPARATOR
+
VILIM
RTN
7.3 Feature Description
7.3.1 Control Overview
The LM25017 buck regulator employs a control principle based on a comparator and a one-shot on-timer, with
the output voltage feedback (FB) compared to an internal reference (1.225 V). If the FB voltage is below the
reference the internal buck switch is turned on for the one-shot timer period, which is a function of the input
voltage and the programming resistor (RON). Following the on-time the switch remains off until the FB voltage
falls below the reference, but never before the minimum off-time forced by the minimum off-time one-shot timer.
When the FB pin voltage falls below the reference and the minimum off-time one-shot period expires, the buck
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
9
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
switch is turned on for another on-time one-shot period. This will continue until regulation is achieved and the FB
voltage is approximately equal to 1.225 V (typ).
In a synchronous buck converter, the low side (sync) FET is ‘on’ when the high side (buck) FET is ‘off’. The
inductor current ramps up when the high side switch is ‘on’ and ramps down when the high side switch is ‘off’.
There is no diode emulation feature in this IC, and therefore, the inductor current may ramp in the negative
direction at light load. This causes the converter to operate in continuous conduction mode (CCM) regardless
of the output loading. The operating frequency remains relatively constant with load and line variations. The
operating frequency can be calculated as shown in Equation 1.
¦SW
VOUT
K u RON
(1)
where
•
K = 9 x 10–11
The output voltage (VOUT) is set by two external resistors (RFB1, RFB2). The regulated output voltage is
calculated as shown in Equation 2.
VOUT
1.225 V u
RFB2 RFB1
RFB1
(2)
This regulator regulates the output voltage based on ripple voltage at the feedback input, requiring a minimum
amount of ESR for the output capacitor (COUT). A minimum of 25-mV ripple voltage at the feedback pin (FB) is
required for the LM25017 device. In cases where the capacitor ESR is too small, additional series resistance
may be required (RC in Figure 7-1).
For applications where lower output voltage ripple is required, the output can be taken directly from a low ESR
output capacitor, as shown in Figure 7-1. However, RC slightly degrades the load regulation.
L1
VOUT
SW
LM25017
RFB2
FB
RC
+
RFB1
COUT
VOUT
(low ripple)
Figure 7-1. Low Ripple Output Configuration
7.3.2 VCC Regulator
The LM25017 device contains an internal high-voltage linear regulator with a nominal output of 7.6 V. The input
pin (VIN) can be connected directly to the line voltages up to 48 V. The VCC regulator is internally current limited
to 30 mA. The regulator sources current into the external capacitor at VCC. This regulator supplies current to
internal circuit blocks including the synchronous MOSFET driver and the logic circuits. When the voltage on the
VCC pin reaches the undervoltage lockout (VCC UVLO) threshold of 4.5 V, the IC is enabled.
An internal diode connected from VCC to the BST pin replenishes the charge in the gate drive bootstrap
capacitor when SW pin is low.
At high-input voltages, the power dissipated in the high voltage regulator is significant and can limit the overall
achievable output power. As an example, with the input at 48 V and switching at high frequency, the VCC
regulator may supply up to 7 mA of current resulting in 48 V × 7 mA = 336 mW of power dissipation. If the VCC
voltage is driven externally by an alternate voltage source between 8.55 V and 13 V, the internal regulator is
disabled. This reduces the power dissipation in the IC.
7.3.3 Regulation Comparator
The feedback voltage at FB is compared to an internal 1.225-V reference. In normal operation, when the output
voltage is in regulation, an on-time period is initiated when the voltage at FB falls below 1.225 V. The high side
10
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
switch will stay on for the on-time, causing the FB voltage to rise above 1.225 V. After the on-time period, the
high side switch will stay off until the FB voltage again falls below 1.225 V. During start up, the FB voltage will be
below 1.225 V at the end of each on-time, causing the high side switch to turn on immediately after the minimum
forced off-time of 144 ns. The high side switch can be turned off before the on-time is over if the peak current in
the inductor reaches the current limit threshold.
7.3.4 Overvoltage Comparator
The feedback voltage at FB is compared to an internal 1.62-V reference. If the voltage at FB rises above 1.62 V
the on-time pulse is immediately terminated. This condition can occur if the input voltage and/or the output load
changes suddenly. The high side switch will not turn on again until the voltage at FB falls below 1.225 V.
7.3.5 On-Time Generator
The on-time for the LM25017 device is determined by the RON resistor and is inversely proportional to the input
voltage (VIN), resulting in a nearly constant frequency as VIN is varied over the operating range. The on-time for
the LM25017 can be calculated using Equation 3.
TON =
10-10 x RON
VIN
(3)
See Figure 6-5. RON should be selected for a minimum on-time (at maximum VIN) greater than 100 ns for proper
operation. This requirement limits the maximum switching frequency for high VIN.
7.3.6 Current Limit
The LM25017 device contains an intelligent current limit off-timer. If the current in the buck switch exceeds
1.02 A, the present cycle is immediately terminated, and a non-resetable off-timer is initiated. The length of the
off-time is controlled by the FB voltage and the input voltage VIN. As an example, when FB = 0 V and VIN = 48 V,
the maximum off-time is set to 16 μs. This condition occurs when the output is shorted and during the initial part
of start-up. This VIN dependent off-time ensures safe short circuit operation up to the maximum input voltage of
48 V.
In cases of overload where the FB voltage is above zero volts (not a short circuit) the current limit off-time is
reduced. Reducing the off-time during less severe overloads reduces the amount of fold-back, recovery time,
and start-up time. The off-time is calculated as shown in Equation 4.
TOFF(ILIM) =
0.07 x VIN
Ps
VFB + 0.2V
(4)
The current limit protection feature is peak limited. The maximum average output current will be less than the
peak.
7.3.7 N-Channel Buck Switch and Driver
The LM25017 device integrates an N-Channel Buck switch and associated floating high-voltage gate driver. The
gate driver circuit works in conjunction with an external bootstrap capacitor and an internal high-voltage diode.
A 0.01-uF ceramic capacitor connected between the BST pin and the SW pin provides the voltage to the driver
during the on-time. During each off-time, the SW pin is at approximately 0 V, and the bootstrap capacitor charges
from VCC through the internal diode. The minimum off-timer, set to 144 ns, ensures a minimum time each cycle
to recharge the bootstrap capacitor.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
11
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
7.3.8 Synchronous Rectifier
The LM25017 device provides an internal synchronous N-Channel MOSFET rectifier. This MOSFET provides a
path for the inductor current to flow when the high-side MOSFET is turned off.
The synchronous rectifier has no diode emulation mode, and is designed to keep the regulator in continuous
conduction mode even with light loads which would otherwise result in discontinuous operation.
7.3.9 Undervoltage Detector
The LM25017 device contains a dual-level undervoltage lockout (UVLO) circuit. A summary of threshold
voltages and operational states is provided in Section 7.4. When the UVLO pin voltage is below 0.66 V, the
regulator is in a low current shutdown mode. When the UVLO pin voltage is greater than 0.66 V but less than
1.225 V, the regulator is in standby mode. In standby mode the VCC bias regulator is active while the regulator
output is disabled. When the VCC pin exceeds the VCC undervoltage threshold and the UVLO pin voltage is
greater than 1.225 V, normal operation begins. An external set-point voltage divider from VIN to GND can be
used to set the minimum operating voltage of the regulator.
UVLO hysteresis is accomplished with an internal 20-μA current source that is switched on or off into the
impedance of the set-point divider. When the UVLO threshold is exceeded, the current source is activated to
quickly raise the voltage at the UVLO pin. The hysteresis is equal to the value of this current times the resistance
RUV2.
If the UVLO pin is connected directly to the VIN pin, the regulator will begin operation once the VCC undervoltage
is satisfied.
VIN
2
VIN
+
CIN
RUV2
LM25017
3
UVLO
RUV1
Figure 7-2. UVLO Resistor Setting
7.3.10 Thermal Protection
The LM25017 device should be operated so the junction temperature does not exceed 150°C during normal
operation. An internal Thermal Shutdown circuit is provided to protect the LM25017 in the event of a higher
than normal junction temperature. When activated, typically at 165°C, the regulator is forced into a low power
reset state, disabling the buck switch and the VCC regulator. This feature prevents catastrophic failures from
accidental device overheating. When the junction temperature falls below 145°C (typical hysteresis = 20°C), the
VCC regulator is enabled, and normal operation is resumed.
7.3.11 Ripple Configuration
LM25017 uses Constant-On-Time (COT) control in which the on-time is terminated by an on-timer and the
off-time is terminated by the feedback voltage (VFB) falling below the reference voltage (VREF). Therefore, for
stable operation, the feedback voltage must decrease monotonically, in phase with the inductor current during
the off-time. Furthermore, this change in feedback voltage (VFB) during off-time must be larger than any noise
component present at the feedback node.
Table 7-1 shows three different methods for generating appropriate voltage ripple at the feedback node. Type 1
and Type 2 ripple circuits couple the ripple at the output of the converter to the feedback node (FB). The output
voltage ripple has two components:
1. Capacitive ripple caused by the inductor current ripple charging/discharging the output capacitor.
2. Resistive ripple caused by the inductor current ripple flowing through the ESR of the output capacitor.
The capacitive ripple is not in phase with the inductor current. As a result, the capacitive ripple does not
decrease monotonically during the off-time. The resistive ripple is in phase with the inductor current and
12
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
decreases monotonically during the off-time. The resistive ripple must exceed the capacitive ripple at the output
node (VOUT) for stable operation. If this condition is not satisfied unstable switching behavior is observed in COT
converters, with multiple on-time bursts in close succession followed by a long off-time.
Type 3 ripple method uses Rr and Cr and the switch node (SW) voltage to generate a triangular ramp. This
triangular ramp is ac coupled using Cac to the feedback node (FB). Since this circuit does not use the output
voltage ripple, it is ideally suited for applications where low output voltage ripple is required. See AN-1481
Controlling Output Ripple and Achieving ESR Independence in Constant On-Time (COT) Regulator Designs
(SNVA166) for more details for each ripple generation method.
Ripple Configuration
TYPE 1
LOWEST COST CONFIGURATION
TYPE 2
REDUCED RIPPLE CONFIGURATION
TYPE 3
MINIMUM RIPPLE CONFIGURATION
VOUT
VOUT
L1
VOUT
L1
L1
R FB2
Cac
R FB2
RC
To FB
Rr
RC
R FB2
Cac
To FB
GND
C OUT
C OUT
R FB1
R FB1
GND
25 mV VOUT
x
RC >
ûIL(MIN) VREF
COUT
Cr
To FB
R FB1
GND
C>
5
gsw (RFB2||RFB1)
25 mV
RC >
ûIL(MIN)
Cr = 3300 pF
Cac = 100 nF
(VIN(MIN) - VOUT) x TON
RrCr <
25 mV
7.3.12 Soft-Start
A soft-start feature can be implemented with the LM25017 device using an external circuit. As shown in Figure
7-3, the soft-start circuit consists of one capacitor, C1, two resistors, R1 and R2, and a diode, D. During the initial
start-up, the VCC voltage is established prior to the VOUT voltage. Capacitor C1 is discharged and diode D is
thereby forward biased to pull up the FB pin voltage. The FB voltage exceeds the reference voltage (1.225 V)
and switching is therefore disabled. As capacitor C1 charges, the voltage at node B gradually decreases and
switching commences. VOUT will gradually rise to maintain the FB voltage at the reference voltage. Once the
voltage at node B is less than a diode drop above the FB voltage, the soft-start sequence is finished and D is
reverse biased.
During the initial part of the start-up, the FB voltage can be approximated as shown in Equation 5.
VFB
(VCC VD ) u
RFB1 u RFB2
R2 u (RFB1 RFB2 ) RFB1 u RFB2
(8)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
13
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
C1 is charged after the first start up. Diode D1 is optional and can be added to discharge C1 when the input
voltage experiences a momentary drop to initialize the soft-start sequence.
To achieve the desired soft start, the following design guidance is recommended:
•
•
R2 is selected so that VFB is higher than 1.225 V for a VCC of 4.5 V, but is lower than 5 V when VCC is 8.55 V.
If an external VCC is used, VFB should not exceed 5 V at maximum VCC.
C1 is selected to achieve the desired start-up time which can be determined from Equation 6.
tS
•
§
C1 u ¨ R2
©
RFB1 u RFB2 ·
¸
RFB1 RFB2 ¹
(9)
R1 is used to maintain the node B voltage at zero after the soft start is finished. A value larger than the
feedback resistor divider is preferred. Note that the effect of resistor R1 is ignored in Equation 5.
Based on the schematic shown in Figure 7-3, selecting C1 = 1 uF, R2 = 1 kΩ, R1 = 30 kΩ results in a soft-start
time of about 2 ms.
VOUT
VCC
C1
RFB2
R2
To FB
D
D1
B
RFB1
R1
Figure 7-3. Soft-Start Circuit
7.4 Device Functional Modes
The UVLO pin controls the operating mode of the LM25017 device (see Table 7-1 for the detailed functional
states).
Table 7-1. UVLO Mode
UVLO
VCC
MODE
< 0.66 V
Disabled
Shutdown
VCC regulator disabled.
Switching disabled.
0.66 V – 1.225 V
Enabled
Standby
VCC regulator enabled
Switching disabled.
VCC < 4.5 V
Standby
VCC regulator enabled.
Switching disabled.
VCC > 4.5 V
Operating
> 1.225 V
14
Submit Document Feedback
DESCRIPTION
VCC enabled.
Switching enabled.
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
8.1 Application Information
The LM25017 device is step-down dc-to-dc converter. The device is typically used to convert a higher dc voltage
to a lower dc voltage with a maximum available output current of 650 mA. Use the following design procedure
to select component values for the LM25017 device. Alternately, use the WEBENCH® software to generate a
complete design. The WEBENCH™ software uses an iterative design procedure and accesses a comprehensive
database of components when generating a design. This section presents a simplified discussion of the design
process.
8.2 Typical Applications
8.2.1 Application Circuit: 12.5-V to 48-V Input and 10-V, 650-mA Output Buck Converter
The application schematic of a buck supply is shown in Figure 8-1. For output voltage (VOUT) above the
maximum regulation threshold of VCC (8.55 V, see Section 6.5), the VCC pin can be connected to VOUT through a
diode (D2), for higher efficiency and lower power dissipation in the IC.
The design example shown in Figure 8-1 uses equations from the Section 7.3 section with component names
provided in the Typical Application . Corresponding component designators from Typical Application Schematic
are also provided for each selected value.
Figure 8-1. Final Schematic for 12.5-V to 48-V Input, and 10-V, 650-mA Output Buck Converter
8.2.1.1 Design Requirements
Selection of external components is illustrated through a design example. The design example specifications are
shown in Table 8-1.
Table 8-1. Buck Converter Design Specifications
DESIGN PARAMETERS
VALUE
Input Range
12.5 V to 48 V
Output Voltage
10 V
Maximum Output Current
650 mA
Nominal Switching Frequency
≈ 480 kHz
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
15
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LM25017 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
8.2.1.2.2 RFB1, RFB2
VOUT = VFB x (RFB2 / RFB1 + 1), and because VFB = 1.225 V, the ratio of RFB2 to RFB1 calculates as 7:1. Standard
values are chosen with RFB2 = R1 = 6.98 kΩ and RFB1 = R6 = 1.00 kΩ are chosen. Other values could be used
as long as the 7:1 ratio is maintained.
8.2.1.2.3 Frequency Selection
At the minimum input voltage, the maximum switching frequency of LM25017 is restricted by the forced minimum
off-time (TOFF(MIN)) as shown in Equation 7.
gSW(MAX) =
1 - DMAX
1 - 10/12.5
=
= 1 MHz
200 ns
TOFF(MIN)
(10)
Similarly, at maximum input voltage, the maximum switching frequency of LM25017 is restricted by the minimum
TON as shown in Equation 8.
gSW(MAX) =
DMIN
10/48
=
= 2.1 MHz
TON(MIN) 100 ns
(11)
Resistor RON sets the nominal switching frequency based on Equation 9.
¦SW
VOUT
K u RON
(12)
where
•
K = 9 x 10–11
Operation at high switching frequency results in lower efficiency while providing the smallest solution. For this
example, 480 kHz was selected, resulting in RON = 231.5 kΩ. Selecting a standard value for RON = R3 = 237 kΩ.
8.2.1.2.4 Inductor Selection
The minimum inductance is selected to limit the output ripple to 15 to 40 percent of the maximum load current. In
addition, the peak inductor current at maximum load should be smaller than the minimum current limit as given in
Section 6.5. The inductor current ripple is shown in Equation 10.
ûIL =
16
VIN - VOUT VOUT
x
VIN
L1 x gSW
(13)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
The maximum ripple is observed at maximum input voltage. To achieve the required output current of 650 mA
without exceeding the peak current limit threshold, low ripple current is required. Substituting VIN = 48 V and
ΔIL = 15 percent x IOUT (max) results in L1 = 169 μH. The higher value of 220 μH is chosen. The peak-to-peak
minimum and maximum inductor current ripples of 19 mA and 75 mA at the minimum and maximum input
voltages respectively. The peak inductor and switch current is shown in Equation 11.
ILI(peak)
IOUT
'IL (max)
2
688 mA
(14)
688 mA is smaller than the minimum current limit threshold, which is 700 mA. The selected inductor should be
able to operate at the maximum current limit of 1.3 A, during startup and overload conditions without saturating.
8.2.1.2.5 Output Capacitor
The output capacitor is selected to minimize the capacitive ripple across it. The maximum ripple is observed at
maximum input voltage and is shown in Equation 12.
COUT =
ûIL
8 x gsw x ûVripple
(15)
where
•
ΔVripple is the voltage ripple across the capacitor.
Substituting ΔVripple = 5 mV gives COUT = 3.9 μF. A 10-μF standard value is selected for COUT = C9. An X5R or
X7R type capacitor with a voltage rating 16 V or higher should be selected.
8.2.1.2.6 Type III Ripple Circuit
Type III ripple circuit as described in Section 7.3.11 is chosen for this example. For a constant on time converter
to be stable, the injected in-phase ripple should be larger than the capacitive ripple on COUT.
Using type III ripple circuit equations, the target ripple should be greater than the capacitive ripple generated at
the primary output.
Cr = C6 = 3300 pF
Cac = C8 = 100 nF
Rr d
(VIN(MIN) VOUT ) u TON(VINMIN)
(25mV u Cr )
(16)
For TON, refer to Equation 3.
Ripple resistor Rr is calculated to be 57.6 kΩ. This value provides the minimum ripple for stable operation. A
smaller resistance should be selected to allow for variations in TON, COUT, and other components. Rr = R4 = 46.4
kΩ is selected for this example application.
8.2.1.2.7 VCC and Bootstrap Capacitor
The VCC capacitor provides charge to bootstrap capacitor as well as internal circuitry and low side gate driver.
The bootstrap capacitor provides charge to high side gate driver. The recommended value for CVCC = C7 is 1
μF. A good value for CBST = C1 is 0.01 μF.
8.2.1.2.8 Input Capacitor
The input capacitor should be large enough to limit the input voltage ripple and can be calculated using Equation
14.
CIN >
IOUT(MAX)
4 x gSW x ûVIN
(17)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
17
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
Choosing a ΔVIN = 0.5 V gives a minimum CIN = 0.68 μF. A standard value of 2.2 μF is selected for CIN = C4.
The input capacitor should be rated for the maximum input voltage under all conditions. A 50-V, X7R dielectric
should be selected for this design.
The input capacitor should be placed directly across VIN and RTN (pin 2 and 1) of the IC. If it is not possible to
place all of the input capacitor close to the IC, a 0.47-μF capacitor should be placed near the IC to provide a
bypass path for the high-frequency component of the switching current. This helps limit the switching noise.
8.2.1.2.9 UVLO Resistors
The UVLO resistors RFB1 and RFB2 set the UVLO threshold and hysteresis according to the following relationship
between Equation 15 and Equation 16.
VIN(HYS) = IHYS x RUV2
VIN (UVLO,rising) = 1.225V x (
(18)
RUV2
+ 1)
RUV1
(19)
where
•
IHYS = 20 μA
Setting UVLO hysteresis of 2.5 V and UVLO rising threshold of 12 V results in RUV1 = 14.53 kΩ and RUV2 = 125
kΩ. Selecting a standard value of RUV1 = R7 = 14 kΩ and RUV2 = R5 = 127 kΩ results in UVLO thresholds and
hysteresis of 12.5 V to 2.5 V respectively.
18
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.1.3 Application Curves
Figure 8-2. Efficiency vs Load Current
Figure 8-3. Frequency vs Input Voltage
Figure 8-4. Typical Switching Waveform (VIN = 24 V, IOUT = 200 mA
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
19
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.2 Typical Isolated DC-DC Converter Using LM25017
An isolated supply using LM25017 is shown in Figure 8-5. Inductor (L) in a typical buck circuit is replaced with a
coupled inductor (X1). A diode (D1) is used to rectify the voltage on a secondary output. The nominal voltage at
the secondary output (VOUT2) is given by Equation 17.
VOUT2
VOUT1 u
NS
NP
VF
(20)
where
•
•
VF is the forward voltage drop of D1
NP and NS are the number of turns on the primary and secondary of coupled inductor X1.
For output voltage (VOUT1) more than one diode drop above the maximum VCC (8.55 V), the VCC pin can be
diode connected to VOUT1 for higher efficiency and low dissipation in the IC. See AN-2292 Designing an Isolated
Buck (Flybuck) Converter (SNVA674) for a complete isolated bias design using the Fly-Buck topology.
VOUT2
D1
+ COUT2
N2
1:1
LM25017
BST
VIN
15V-48V
CIN +
2.2 µF
VIN
CBYP
0.47 µF
+
RUV2
127 kΩ
RON
124 kΩ
SW
N1
100 µH
VOUT1
46.4 kΩ 1 nF
Rr
Cr
+ COUT1
Cac
RON
0.1 µF
4.7 µF
RFB2
VCC
UVLO
RUV1
RTN
11.8 kΩ
0.01 µF
+ CBST
2.2 µF
X1
D2
10 kΩ
+ CVCC
RFB1
1 µF
3.4 kΩ
FB
Figure 8-5. Typical Isolated Application Schematic
8.2.2.1 Design Requirements
Selection of external components is illustrated through a design example. The design example specifications are
shown in Table 8-2.
Table 8-2. Buck Converter Design Specifications
DESIGN PARAMETERS
VALUE
Input Range
15 V to 48 V
Primary Output Voltage
5V
Secondary (Isolated) Output Voltage
4.5 V
Maximum Output Current (Primary + Secondary)
600 mA
Maximum Power Output
3W
Nominal Switching Frequency
500 kHz
8.2.2.2 Detailed Design Procedure
8.2.2.2.1 Transformer Turns Ratio
The transformer turns ratio is selected based on the ratio of the primary output voltage to the secondary
(isolated) output voltage. In this design example, the two outputs are nearly equal and a 1:1 turns ratio
transformer is selected. Therefore, N2 / N1 = 1. If the secondary (isolated) output voltage is significantly higher
or lower than the primary output voltage, a turns ratio less than or greater than 1 is recommended. The primary
output voltage is normally selected based on the input voltage range such that the duty cycle of the converter
does not exceed 50% at the minimum input voltage. This condition is satisfied if VOUT1 < VIN_MIN / 2.
20
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.2.2.2 Total IOUT
The total primary referred load current is calculated by multiplying the isolated output load(s) by the turns ratio of
the transformer as shown in Equation 18.
IOUT(MAX)
IOUT1 IOUT2 u
N2
N1
0.6 A
(21)
8.2.2.2.3 RFB1, RFB2
The feedback resistors are selected to set the primary output voltage. The selected value for RFB1 is 3.4 kΩ.
RFB2 can be calculated using the following equations to set VOUT1 to the specified value of 5 V. A standard
resistor value of 10.0 kΩ is selected for RFB2.
VOUT1 = 1.225V x (1 +
RFB2
)
RFB1
§ VOUT1 ·
1¸ u RFB1
¨
© 1.225
¹
o RFB2
(22)
10.4 k:
(23)
8.2.2.2.4 Frequency Selection
Equation 21 is used to calculate the value of RON required to achieve the desired switching frequency.
¦SW
VOUT1
K u RON
(24)
Where K = 9 × 10–11For VOUT1 of 5 V and fSW of 500 kHz, the calculated value of RON is 111 kΩ. A standard
value of 124 kΩ is selected for this design to allow for second order effects at high switching frequency that are
not included in Equation 21.
8.2.2.2.5 Transformer Selection
A coupled inductor or a flyback-type transformer is required for this topology. Energy is transferred from primary
to secondary when the low-side synchronous switch of the buck converter is conducting.
The maximum inductor primary ripple current that can be tolerated without exceeding the buck switch peak
current limit threshold (0.7 A minimum) is given by Equation 22.
'IL1
N2 ·
§
¨ 0.7 IOUT1 IOUT2 u N1 ¸ u 2
©
¹
0.2 A
(25)
Using the maximum peak-to-peak inductor ripple current ΔIL1 from Equation 22, the minimum inductor value is
given by Equation 23.
L1
VIN(MAX)
VOUT
'IL1 u ¦SW
u
VOUT
VIN(MAX)
44.4 PH
(26)
A higher value of 100 µH is selected to insure the high-side switch current does not exceed the minimum peak
current limit threshold. With this inductance, the inductor current ripple is ΔIL1= 90 mA at the maximum VIN.
8.2.2.2.6 Primary Output Capacitor
In a conventional buck converter the output ripple voltage is calculated as shown in Equation 24.
f
'VOUT =
'IL1
x f x COUT1
(27)
To limit the primary output ripple voltage ΔVOUT1 to approximately 25 mV, an output capacitor COUT1 of 0.9 µF
would be required for a conventional buck.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
21
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
Figure 8-6 shows the primary winding current waveform (IL1) of a Fly-Buck™ converter. The reflected secondary
winding current adds to the primary winding current during the buck switch off-time. Because of this increased
current, the output voltage ripple is not the same as in conventional buck converter. The output capacitor value
calculated in Equation 24 should be used as the starting point. Optimization of output capacitance over the entire
line and load range must be done experimentally. If the majority of the load current is drawn from the secondary
isolated output, a better approximation of the primary output voltage ripple is given by Equation 25.
'VOUT1
N2 ·
§
¨ IOUT2 u N1 ¸ u TON(MAX)
©
¹
COUT1
(28)
TON(MAX) x IOUT2 x N2/N1
IL1
IOUT2
IL2
TON(MAX) x IOUT2
Figure 8-6. Current Waveforms for COUT1 Ripple Calculation
To limit the primary output ripple voltage to approximately 100 mV, an output capacitor of 4 μF is required. A
standard 4.7-µF, 16 V capacitor is selected for this design. If lower output voltage ripple is required, a higher
value should be selected for COUT1 and/or COUT2.
8.2.2.2.7 Secondary Output Capacitor
A simplified waveform for secondary output current (IOUT2) is shown in Figure 8-7.
IOUT2
IL2
TON(MAX) x IOUT2
Figure 8-7. Secondary Current Waveforms for COUT2 Ripple Calculation
The secondary output current (IOUT2) is sourced by COUT2 during on-time of the buck switch, TON. Ignoring
the current transition times in the secondary winding, the secondary output capacitor ripple voltage can be
calculated using Equation 26.
'VOUT2 =
IOUT2 x TON (MAX)
COUT2
(29)
For a 1:1 transformer turns ratio, the primary and secondary voltage ripple equations are identical. A COUT2
value of 2.2 µF is chosen for this design.
If lower output voltage ripple is required, a higher value should be selected for COUT1 and/or COUT2.
22
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.2.2.8 Type III Feedback Ripple Circuit
Type III ripple circuit as described in Section 7.3.11 is required for the Fly-Buck topology. Type I and Type II
ripple circuits use series resistance and the triangular inductor ripple current to generate ripple at VOUT and the
FB pin. The primary ripple current of a Fly-Buck is the combination or primary and reflected secondary currents
as illustrated in Figure 8-6. In the Fly-Buck topology, Type I and Type II ripple circuits suffer from large jitter as
the reflected load current affects the feedback ripple.
VOUT
L1
Rr
Cac
C OUT
Cr
R FB2
GND
To FB
R FB1
Figure 8-8. Type III Ripple Circuit
Selecting the Type III ripple components using the equations from Table 7-1 will ensure that the FB pin ripple
is greater than the capacitive ripple from the primary output capacitor COUT1. The feedback ripple component
values are chosen as shown in Equation 27.
Rr Cr d
(VIN(MIN)
VOUT ) u TON
(30)
100 mV
The calculated value for Rr is 66 kΩ. This value provides the minimum ripple for stable operation. A smaller
resistance should be selected to allow for variations in TON, COUT1 and other components. For this design, Rr
value of 46.4 kΩ is selected.
8.2.2.2.9 Secondary Diode
The reverse voltage across secondary-rectifier diode D1 when the high-side buck switch is off can be calculated
using Equation 28.
VD1 =
N2
VIN
N1
(31)
For a VIN_MAX of 48 V and the 1:1 turns ratio of this design, a 60 V Schottky is selected.
8.2.2.2.10 VCC and Bootstrap Capacitor
A 1-µF capacitor of 16 V or higher rating is recommended for the VCC regulator bypass capacitor.
A good value for the BST pin bootstrap capacitor is 0.01-µF with a 16 V or higher rating.
8.2.2.2.11 Input Capacitor
The input capacitor is typically a combination of a smaller bypass capacitor located near the regulator IC and
a larger bulk capacitor. The total input capacitance should be large enough to limit the input voltage ripple to a
desired amplitude. For input ripple voltage ΔVIN, CIN can be calculated using Equation 29.
CIN t
IOUT(MAX)
4 u f u 'VIN
(32)
Choosing a ΔVIN of 0.5 V gives a minimum CIN of 0.6 μF. A standard value of 0.47 μF is selected for CBYP in this
design. A bulk capacitor of higher value reduces voltage spikes due to parasitic inductance between the power
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
23
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
source to the converter. A standard value of 2.2 μF is selected for CIN in this design. The voltage ratings of the
two input capacitors should be greater than the maximum input voltage under all conditions.
8.2.2.2.12 UVLO Resistors
UVLO resistors RUV1 and RUV2 set the undervoltage lockout threshold and hysteresis according to Equation 30
and Equation 31.
VIN (HYS) = IHYS x RUV2
§R
VIN (UVLO, rising) 1.225 V u ¨ UV2
© RUV1
(33)
·
1¸
¹
(34)
where
•
IHYS = 20 μA, typical.
For a UVLO hysteresis of 2.5 V and UVLO rising threshold of 15 V, Equation 30 and Equation 31 require RUV1 of
11.8 kΩ and RUV2 of 127 kΩ and these values are selected for this design example.
8.2.2.2.13 VCC Diode
Diode D2 is an optional diode connected between VOUT1 and the VCC regulator output pin. When VOUT1 is more
than one diode drop greater than the VCC voltage, the VCC bias current is supplied from VOUT1. This results in
reduced power losses in the internal VCC regulator which improves converter efficiency. VOUT1 must be set to
a voltage at least one diode drop higher than 8.55 V (the maximum VCC voltage) if D2 is used to supply bias
current.
24
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
8.2.2.3 Application Curves
Figure 8-9. Steady State Waveform (VIN = 24 V,
IOUT1 = 100 mA, IOUT2 = 200 mA)
Figure 8-10. Step Load Response (VIN = 24 V, IOUT1
= 0, Step Load on IOUT2 = 100 mA to 200 mA)
Figure 8-11. Efficiency at 500 kHz, VOUT1 = 5 V, VOUT2 = 4.5 V
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
25
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
9 Power Supply Recommendations
LM25017 is a power management device. The power supply for the device is any dc voltage source within the
specified input range.
26
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
10 Layout
10.1 Layout Guidelines
A proper layout is essential for optimum performance of the circuit. In particular, the following guidelines should
be observed:
•
•
•
•
CIN: The loop consisting of input capacitor (CIN), VIN pin, and RTN pin carries switching currents. Therefore,
the input capacitor should be placed close to the IC, directly across VIN and RTN pins and the connections to
these two pins should be direct to minimize the loop area. In general it is not possible to accommodate all of
input capacitance near the IC. A good practice is to use a 0.1-μF or 0.47-μF capacitor directly across the VIN
and RTN pins close to the IC, and the remaining bulk capacitor as close as possible (see Figure 10-1).
CVCC and CBST: The VCC and bootstrap (BST) bypass capacitors supply switching currents to the high and
low side gate drivers. These two capacitors should also be placed as close to the IC as possible, and the
connecting trace length and loop area should be minimized (see Figure 10-1).
The Feedback trace carries the output voltage information and a small ripple component that is necessary
for proper operation of LM25017 device. Therefore, care should be taken while routing the feedback trace
to avoid coupling any noise to this pin. In particular, feedback trace should not run close to magnetic
components, or parallel to any other switching trace.
SW trace: The SW node switches rapidly between VIN and GND every cycle and is therefore a possible
source of noise. The SW node area should be minimized. In particular, the SW node should not be
inadvertently connected to a copper plane or pour.
10.2 Layout Example
RTN
1
VIN
2
UVLO
3
RON
4
8
SW
7
BST
6
VCC
5
FB
CIN
SO
Power
PAD-8
CVCC
Figure 10-1. Placement of Bypass Capacitors
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
27
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
11 Device and Documentation Support
11.1 Device Support
11.1.1 Development Support
11.1.1.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LM25017 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.2 Documentation Support
11.2.1 Related Documentation
•
•
•
•
AN-1481Controlling Output Ripple and Achieving ESR Independence in Constant On-Time (COT) Regulator
Designs
AN-2292 Designing an Isolated Buck (Flybuck) Converter
LM25017 Evaluation Board
LM25017 Isolated Buck (FlyBuck) User's Guide
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.5 Trademarks
Fly-Buck™ and TI E2E™ are trademarks of Texas Instruments.
is a trademark of Texas Instruments.
WEBENCH® are registered trademarks of Texas Instruments.
All trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
28
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
LM25017
www.ti.com
SNVS951F – DECEMBER 2012 – REVISED MAY 2021
11.7 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: LM25017
29
PACKAGE OPTION ADDENDUM
www.ti.com
2-Jun-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
LM25017MR/NOPB
ACTIVE SO PowerPAD
DDA
8
95
RoHS & Green
NIPDAU | SN
Level-3-260C-168 HR
-40 to 125
L25017
MR
Samples
LM25017MRE/NOPB
ACTIVE SO PowerPAD
DDA
8
250
RoHS & Green
NIPDAU | SN
Level-3-260C-168 HR
-40 to 125
L25017
MR
Samples
LM25017MRX/NOPB
ACTIVE SO PowerPAD
DDA
8
2500
RoHS & Green
NIPDAU | SN
Level-3-260C-168 HR
-40 to 125
L25017
MR
Samples
LM25017SD/NOPB
ACTIVE
WSON
NGU
8
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
L25017
Samples
LM25017SDE/NOPB
ACTIVE
WSON
NGU
8
250
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
L25017
Samples
LM25017SDX/NOPB
ACTIVE
WSON
NGU
8
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
L25017
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
