LM2674
SIMPLE SWITCHER® Power Converter High Efficiency
500 mA Step-Down Voltage Regulator
General Description
Features
The LM2674 series of regulators are monolithic integrated
circuits built with a LMDMOS process. These regulators provide all the active functions for a step-down (buck) switching
regulator, capable of driving a 500 mA load current with excellent line and load regulation. These devices are available
in fixed output voltages of 3.3V, 5.0V, 12V, and an adjustable
output version.
Requiring a minimum number of external components, these
regulators are simple to use and include patented internal
frequency compensation (Patent Nos. 5,382,918 and
5,514,947) and a fixed frequency oscillator.
The LM2674 series operates at a switching frequency of
260 kHz, thus allowing smaller sized filter components than
what would be needed with lower frequency switching regulators. Because of its very high efficiency (>90%), the copper
traces on the printed circuit board are the only heat sinking
needed.
A family of standard inductors for use with the LM2674 are
available from several different manufacturers. This feature
greatly simplifies the design of switch-mode power supplies
using these advanced ICs. Also included in the datasheet are
selector guides for diodes and capacitors designed to work in
switch-mode power supplies.
Other features include a guaranteed ±1.5% tolerance on output voltage within specified input voltages and output load
conditions, and ±10% on the oscillator frequency. External
shutdown is included, featuring typically 50 μA stand-by current. The output switch includes current limiting, as well as
thermal shutdown for full protection under fault conditions.
To simplify the LM2674 buck regulator design procedure,
there exists computer design software, LM267X Made Simple (version 6.0).
■ Efficiency up to 96%
■ Available in SO-8, 8-pin DIP and LLP packages
■ Computer Design Software LM267X Made Simple
(version 6.0)
Simple and easy to design with
Requires only 5 external components
Uses readily available standard inductors
3.3V, 5.0V, 12V, and adjustable output versions
Adjustable version output voltage range: 1.21V to 37V
±1.5% max output voltage tolerance over line and load
conditions
■ Guaranteed 500mA output load current
■ 0.25Ω DMOS Output Switch
■ Wide input voltage range: 8V to 40V
■ 260 kHz fixed frequency internal oscillator
■ TTL shutdown capability, low power standby mode
■ Thermal shutdown and current limit protection
■
■
■
■
■
■
Typical Applications
■ Simple High Efficiency (>90%) Step-Down (Buck)
Regulator
■ Efficient Pre-Regulator for Linear Regulators
■ Positive-to-Negative Converter
Typical Application
10004101
SIMPLE SWITCHER® is a registered trademark of National Semiconductor Corporation
Windows® is a registered trademark of Microsoft Corporation.
© 2012 Texas Instruments Incorporated
100041 SNVS007E
www.ti.com
LM2674 SIMPLE SWITCHER Power Converter High Efficiency 500 mA Step-Down Voltage
Regulator
February 15, 2012
LM2674
Connection Diagrams
16-Lead LLP Surface Mount Package
Top View
8-Lead Package
Top View
10004102
SO-8/DIP Package
See NSC Package Drawing Number MO8A/N08E
10004138
LLP Package
See NSC Package Drawing Number LDA16A
TABLE 1. Package Marking and Ordering Information
Output Voltage
Order Information
Package Marking
Supplied as:
3.3
LM2674LD-3.3
S000AB
1000 Units on Tape and Reel
5.0
LM2674LDX-5.0
S000BB
4500 Units on Tape and Reel
ADJ
LM2674LD-ADJ
S000CB
1000 Units on Tape and Reel
12
LM2674M-12
2674M-12
Shipped in Anti-Static Rails
12
LM2674MX-12
2674M-12
2500 Units on Tape and Reel
3.3
LM2674M-3.3
2674M-3.3
Shipped in Anti-Static Rails
3.3
LM2674MX-3.3
2674M-3.3
2500 Units on Tape and Reel
5.0
LM2674M-5.0
2674M-5.0
Shipped in Anti-Static Rails
16 Lead LLP
SO-8
5.0
LM2674MX-5.0
2674M-5.0
2500 Units on Tape and Reel
ADJ
LM2674M-ADJ
2674M-ADJ
Shipped in Anti-Static Rails
ADJ
LM2674MX-ADJ
2674M-ADJ
2500 Units on Tape and Reel
DIP
www.ti.com
12
LM2674N-12
LM2674N-12
Shipped in Anti-Static Rails
3.3
LM2674N-3.3
LM2674N-3.3
Shipped in Anti-Static Rails
5.0
LM2674N-5.0
LM2674N-5.0
Shipped in Anti-Static Rails
ADJ
LM2674N-ADJ
LM2674N-ADJ
Shipped in Anti-Static Rails
2
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for
availability and specifications.
Storage Temperature Range
−65°C to +150°C
Supply Voltage
45V
Lead Temperature
ON/OFF Pin Voltage
−0.1V ≤ VSH ≤ 6V
M Package
Switch Voltage to Ground
−1V
Vapor Phase (60s)
+215°C
Boost Pin Voltage
VSW + 8V
Infrared
(15s)
+220°C
Feedback Pin Voltage
−0.3V ≤ VFB ≤ 14V
N Package (Soldering, 10s)
+260°C
ESD Susceptibility
LLP Package (See AN-1187)
Human Body Model (Note 2)
2 kV
Maximum Junction Temperature
+150°C
Power Dissipation
Internally Limited
Operating Ratings
Supply Voltage
Junction Temperature Range
6.5V to 40V
−40°C ≤ TJ ≤ +125°C
Electrical Characteristics
LM2674-3.3 Specifications with standard type face are for TJ = 25°C, and those with bold type face apply over full
Operating Temperature Range.
Symbol
Parameter
Conditions
Typical
(Note 4)
Min
(Note 5)
Max
(Note 5)
Units
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 8V to 40V, ILOAD = 20 mA to 500 mA
3.3
3.251/3.201
3.350/3.399
V
VOUT
Output Voltage
VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA
3.3
3.251/3.201
3.350/3.399
V
η
Efficiency
VIN = 12V, ILOAD = 500 mA
86
%
LM2674-5.0
Symbol
Parameter
Conditions
Typical
(Note 4)
Min
(Note 5)
Max
(Note 5)
Units
V
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 8V to 40V, ILOAD = 20 mA to 500 mA
5.0
4.925/4.850
5.075/5.150
VOUT
Output Voltage
VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA
5.0
4.925/4.850
5.075/5.150
η
Efficiency
VIN = 12V, ILOAD = 500 mA
90
V
%
LM2674-12
Symbol
Parameter
Conditions
Typical
(Note 4)
Min
(Note 5)
Max
(Note 5)
11.82/11.64
12.18/12.36
Units
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT
Output Voltage
VIN = 15V to 40V, ILOAD = 20 mA to 500 mA
12
η
Efficiency
VIN = 24V, ILOAD = 500 mA
94
3
V
%
www.ti.com
LM2674
Absolute Maximum Ratings (Note 1)
LM2674
LM2674-ADJ
Symbol
Typ
(Note 4)
Min
(Note 5)
Max
(Note 5)
Units
Feedback Voltage VIN = 8V to 40V, ILOAD = 20 mA to 500 mA
VOUT Programmed for 5V
(see Circuit of Figure 3)
1.210
1.192/1.174
1.228/1.246
V
Feedback Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA
VOUT Programmed for 5V
(see Circuit of Figure 3)
1.210
1.192/1.174
1.228/1.246
V
Parameter
Conditions
SYSTEM PARAMETERS Test Circuit Figure 3 (Note 3)
VFB
VFB
η
Efficiency
VIN = 12V, ILOAD = 500 mA
90
%
All Output Voltage Versions
Specifications with standard type face are for TJ = 25°C, and those with bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable versions and VIN = 24V for the 12V version, and
ILOAD = 100 mA.
Symbol
Parameters
Conditions
Typ
Min
Max
Units
3.6
mA
DEVICE PARAMETERS
IQ
Quiescent Current
VFEEDBACK = 8V
2.5
For 3.3V, 5.0V, and ADJ Versions
VFEEDBACK = 15V
2.5
mA
For 12V Versions
100/150
μA
1.2/1.25
A
25
μA
6
15
mA
0.25
0.40/0.60
Ω
275
kHz
ISTBY
Standby Quiescent Current ON/OFF Pin = 0V
50
ICL
Current Limit
0.8
IL
Output Leakage Current
RDS(ON)
Switch On-Resistance
ISWITCH = 500 mA
fO
Oscillator Frequency
Measured at Switch Pin
260
D
Maximum Duty Cycle
VIN = 40V, ON/OFF Pin = 0V
VSWITCH = 0V
VSWITCH = −1V, ON/OFF Pin = 0V
Minimum Duty Cycle
0.62/0.575
1
225
95
%
0
%
IBIAS
Feedback Bias
Current
VFEEDBACK = 1.3V
ADJ Version Only
85
nA
VS/D
ON/OFF Pin
Voltage Theshold
Turn-On Threshold, Rising (Note 7)
1.4
0.8
2.0
IS/D
ON/OFF Pin Current
ON/OFF Pin = 0V
20
7
37
θJA
Thermal Resistance
N Package, Junction to Ambient (Note 6)
95
M Package, Junction to Ambient (Note 6)
105
V
μA
°C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions,
see the Electrical Characteristics.
Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
Note 3: External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator
performance. When the LM2674 is used as shown in Figures 2, 3 test circuits, system performance will be as specified by the system parameters section of the
Electrical Characteristics.
Note 4: Typical numbers are at 25°C and represent the most likely norm.
Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used
to calculate Average Outgoing Quality Level (AOQL).
Note 6: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area
will lower thermal resistance further. See Application Information section in the application note accompanying this datasheet and the thermal model in LM267X
Made Simple (version 6.0) software. The value θJ−A for the LLP (LD) package is specifically dependent on PCB trace area, trace material, and the number of
layers and thermal vias. For improved thermal resistance and power dissipation for the LLP package, refer to Application Note AN-1187.
Note 7: The ON/OFF pin is internally pulled up to 7V and can be left floating for always-on operation.
www.ti.com
4
LM2674
Typical Performance Characteristics
Normalized
Output Voltage
Line Regulation
10004104
10004103
Efficiency
Drain-to-Source
Resistance
10004105
10004106
Switch Current Limit
Operating
Quiescent Current
10004107
10004108
5
www.ti.com
LM2674
Standby
Quiescent Current
ON/OFF Threshold
Voltage
10004109
10004110
ON/OFF Pin
Current (Sourcing)
Switching Frequency
10004112
10004111
Peak Switch Current
Feedback Pin
Bias Current
10004113
www.ti.com
10004114
6
LM2674
Dropout Voltage—3.3V Option
Dropout Voltage—5.0V Option
10004115
10004116
Typical Performance Characteristics
(Circuit of Figure 2)
Continuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 500 mA
L = 100 μH, COUT = 100 μF, COUTESR = 0.1Ω
Discontinuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 300 mA
L = 15 μH, COUT = 68 μF (2×), COUTESR = 25 mΩ
10004118
A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 0.2 A/div
C: Output Ripple Voltage, 50 mV/div AC-Coupled
10004119
A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 0.5 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled
Horizontal Time Base: 1 μs/div
Horizontal Time Base: 1 μs/div
Load Transient Response for Continuous Mode
VIN = 20V, VOUT = 5V,
L = 100 μH, COUT = 100 μF, COUTESR = 0.1Ω
Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V,
L = 47 μH, COUT = 68 μF, COUTESR = 50 mΩ
10004120
A: Output Voltage, 100 mV/div, AC-Coupled.
B: Load Current: 100 mA to 500 mA Load Pulse
10004121
A: Output Voltage, 100 mV/div, AC-Coupled.
B: Load Current: 100 mA to 400 mA Load Pulse
Horizontal Time Base: 50 μs/div
Horizontal Time Base: 200 μs/div
7
www.ti.com
LM2674
Block Diagram
10004117
* Active Inductor Patent Number 5,514,947
† Active Capacitor Patent Number 5,382,918
FIGURE 1.
Test Circuit and Layout Guidelines
10004122
CIN - 22 μF, 50V Tantalum, Sprague “199D Series”
COUT - 47 μF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 μH Sumida #RCR110D-680L
CB - 0.01 μF, 50V Ceramic
FIGURE 2. Standard Test Circuits and Layout Guides
Fixed Output Voltage Versions
www.ti.com
8
LM2674
10004123
CIN - 22 μF, 50V Tantalum, Sprague “199D Series”
COUT - 47 μF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 μH Sumida #RCR110D-680L
R1 - 1.5 kΩ, 1%
CB - 0.01 μF, 50V Ceramic
For a 5V output, select R2 to be 4.75 kΩ, 1%
where VREF = 1.21V
Use a 1% resistor for best stability.
FIGURE 3. Standard Test Circuits and Layout Guides
Adjustable Output Voltage Versions
9
www.ti.com
LM2674
LM2674 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to be
used with the SIMPLE SWITCHER line of switching regulators.
LM267X Made Simple (version 6.0)is available on Windows® 3.1,
NT, or 95 operating systems.
Given:
Given:
VOUT = Regulated Output Voltage (3.3V, 5V, or 12V)
VOUT = 5V
VIN(max) = Maximum DC Input Voltage
VIN(max) = 12V
ILOAD(max) = Maximum Load Current
ILOAD(max) = 500 mA
1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from Figure
4, Figure 5 or Figure 6 (output voltages of 3.3V, 5V, or 12V
respectively). For all other voltages, see the design procedure for
the adjustable version.
B. From the inductor value selection guide, identify the inductance
region intersected by the Maximum Input Voltage line and the
Maximum Load Current line. Each region is identified by an
inductance value and an inductor code (LXX).
C. Select an appropriate inductor from the four manufacturer's part
numbers listed in Figure 8. Each manufacturer makes a different
style of inductor to allow flexibility in meeting various design
requirements. Listed below are some of the differentiating
characteristics of each manufacturer's inductors:
Schott: ferrite EP core inductors; these have very low leakage
magnetic fields to reduce electro-magnetic interference (EMI) and
are the lowest power loss inductors
Renco: ferrite stick core inductors; benefits are typically lowest cost
inductors and can withstand E•T and transient peak currents above
rated value. Be aware that these inductors have an external
magnetic field which may generate more EMI than other types of
inductors.
Pulse: powered iron toroid core inductors; these can also be low
cost and can withstand larger than normal E•T and transient peak
currents. Toroid inductors have low EMI.
Coilcraft: ferrite drum core inductors; these are the smallest
physical size inductors, available only as SMT components. Be
aware that these inductors also generate EMI—but less than stick
inductors.
Complete specifications for these inductors are available from the
respective manufacturers. A table listing the manufacturers' phone
numbers is located in Figure 9.
2. Output Capacitor Selection (COUT)
1. Inductor Selection (L1)
A. Use the inductor selection guide for the 5V version shown in
Figure 5.
A. Select an output capacitor from the output capacitor table in
Figure 10. Using the output voltage and the inductance value found
in the inductor selection guide, step 1, locate the appropriate
capacitor value and voltage rating.
A. Use the 5.0V section in the output capacitor table in Figure 10.
Choose a capacitor value and voltage rating from the line that
contains the inductance value of 47 μH. The capacitance and
voltage rating values corresponding to the 47 μH inductor are the:
www.ti.com
B. From the inductor value selection guide shown in Figure 5, the
inductance region intersected by the 12V horizontal line and the
500mA vertical line is 47 μH, and the inductor code is L13.
C. The inductance value required is 47 μH. From the table in Figure
8, go to the L13 line and choose an inductor part number from any
of the four manufacturers shown. (In most instances, both through
hole and surface mount inductors are available.)
2. Output Capacitor Selection (COUT)
10
EXAMPLE (Fixed Output Voltage Version)
The capacitor list contains through-hole electrolytic capacitors from
four different capacitor manufacturers and surface mount tantalum
capacitors from two different capacitor manufacturers. It is
recommended that both the manufacturers and the manufacturer's
series that are listed in the table be used. A table listing the
manufacturers' phone numbers is located in Figure 11.
Surface Mount:
68 μF/10V Sprague 594D Series.
100 μF/10V AVX TPS Series.
Through Hole:
68 μF/10V Sanyo OS-CON SA Series.
150 μF/35V Sanyo MV-GX Series.
150 μF/35V Nichicon PL Series.
150 μF/35V Panasonic HFQ Series.
3. Catch Diode Selection (D1)
3. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. In this example, a 1A,
the load current times the catch diode duty cycle, 1-D (D is the
20V Schottky diode will provide the best performance. If the circuit
switch duty cycle, which is approximately the output voltage divided must withstand a continuous shorted output, a higher current
by the input voltage). The largest value of the catch diode average Schottky diode is recommended.
current occurs at the maximum load current and maximum input
voltage (minimum D). For normal operation, the catch diode current
rating must be at least 1.3 times greater than its maximum average
current. However, if the power supply design must withstand a
continuous output short, the diode should have a current rating
equal to the maximum current limit of the LM2674. The most
stressful condition for this diode is a shorted output condition.
B. The reverse voltage rating of the diode should be at least 1.25
times the maximum input voltage.
C. Because of their fast switching speed and low forward voltage
drop, Schottky diodes provide the best performance and efficiency.
This Schottky diode must be located close to the LM2674 using
short leads and short printed circuit traces.
4. Input Capacitor (CIN)
4. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. This capacitor should be
located close to the IC using short leads. In addition, the RMS
current rating of the input capacitor should be selected to be at least
½ the DC load current. The capacitor manufacturer data sheet must
be checked to assure that this current rating is not exceeded. The
curves shown in Figure 14 show typical RMS current ratings for
several different aluminum electrolytic capacitor values. A parallel
connection of two or more capacitors may be required to increase
the total minimum RMS current rating to suit the application
requirements.
For an aluminum electrolytic capacitor, the voltage rating should be
at least 1.25 times the maximum input voltage. Caution must be
exercised if solid tantalum capacitors are used. The tantalum
capacitor voltage rating should be twice the maximum input
voltage. The tables in Figure 15 show the recommended
application voltage for AVX TPS and Sprague 594D tantalum
capacitors. It is also recommended that they be surge current
tested by the manufacturer. The TPS series available from AVX,
and the 593D and 594D series from Sprague are all surge current
tested. Another approach to minimize the surge current stresses
on the input capacitor is to add a small inductor in series with the
input supply line.
Use caution when using only ceramic capacitors for input
bypassing, because it may cause severe ringing at the VIN pin.
The important parameters for the input capacitor are the input
voltage rating and the RMS current rating. With a maximum input
voltage of 12V, an aluminum electrolytic capacitor with a voltage
rating greater than 15V (1.25 × VIN) would be needed. The next
higher capacitor voltage rating is 16V.
The RMS current rating requirement for the input capacitor in a
buck regulator is approximately ½ the DC load current. In this
example, with a 500mA load, a capacitor with an RMS current rating
of at least 250 mA is needed. The curves shown in Figure 14 can
be used to select an appropriate input capacitor. From the curves,
locate the 16V line and note which capacitor values have RMS
current ratings greater than 250 mA.
For a through hole design, a 100 μF/16V electrolytic capacitor
(Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
equivalent) would be adequate. Other types or other
manufacturers' capacitors can be used provided the RMS ripple
current ratings are adequate. Additionally, for a complete surface
mount design, electrolytic capacitors such as the Sanyo CV-C or
CV-BS and the Nichicon WF or UR and the NIC Components NACZ
series could be considered.
For surface mount designs, solid tantalum capacitors can be used,
but caution must be exercised with regard to the capacitor surge
current rating and voltage rating. In this example, checking Figure
15, and the Sprague 594D series datasheet, a Sprague 594D 15
μF, 25V capacitor is adequate.
11
www.ti.com
LM2674
PROCEDURE (Fixed Output Voltage Version)
LM2674
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
5. Boost Capacitor (CB)
5. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch
gate on fully. All applications should use a 0.01 μF, 50V ceramic
capacitor.
For this application, and all applications, use a 0.01 μF, 50V
ceramic capacitor.
www.ti.com
12
LM2674
Inductor Value Selection Guides
(For Continuous Mode Operation)
10004128
10004126
FIGURE 6. LM2674-12
FIGURE 4. LM2674-3.3
10004129
10004127
FIGURE 7. LM2674-ADJ
FIGURE 5. LM2674-5.0
Ind. Inducta
nce
Ref.
Desg.
(μH)
Current
(A)
Schott
Through
Hole
Surface
Mount
Renco
Through
Hole
Pulse Engineering
Surface
Mount
Through
Hole
Surface
Mount
Coilcraft
Surface
Mount
L2
150
0.21
67143920 67144290 RL-5470-4
RL1500-150 PE-53802 PE-53802-S DO1608-154
L3
100
0.26
67143930 67144300 RL-5470-5
RL1500-100 PE-53803 PE-53803-S DO1608-104
L4
68
0.32
67143940 67144310
RL-1284-68-43
RL1500-68
PE-53804 PE-53804-S DO1608-683
L5
47
0.37
67148310 67148420
RL-1284-47-43
RL1500-47
PE-53805 PE-53805-S DO1608-473
L6
33
0.44
67148320 67148430
RL-1284-33-43
RL1500-33
PE-53806 PE-53806-S DO1608-333
L7
22
0.52
67148330 67148440
RL-1284-22-43
RL1500-22
PE-53807 PE-53807-S DO1608-223
L9
220
0.32
67143960 67144330
RL-5470-3
RL1500-220 PE-53809 PE-53809-S DO3308-224
L10
150
0.39
67143970 67144340
RL-5470-4
RL1500-150 PE-53810 PE-53810-S DO3308-154
L11
100
0.48
67143980 67144350
RL-5470-5
RL1500-100 PE-53811 PE-53811-S DO3308-104
L12
68
0.58
67143990 67144360
RL-5470-6
RL1500-68
PE-53812 PE-53812-S DO3308-683
L13
47
0.70
67144000 67144380
RL-5470-7
RL1500-47
PE-53813 PE-53813-S DO3308-473
L14
33
0.83
67148340 67148450
RL-1284-33-43
RL1500-33
PE-53814 PE-53814-S DO3308-333
L15
22
0.99
67148350 67148460
RL-1284-22-43
RL1500-22
PE-53815 PE-53815-S DO3308-223
L18
220
0.55
67144040 67144420
RL-5471-2
RL1500-220 PE-53818 PE-53818-S DO3316-224
L19
150
0.66
67144050 67144430
RL-5471-3
RL1500-150 PE-53819 PE-53819-S DO3316-154
L20
100
0.82
67144060 67144440
RL-5471-4
RL1500-100 PE-53820 PE-53820-S DO3316-104
L21
68
0.99
67144070 67144450
RL-5471-5
RL1500-68
13
PE-53821 PE-53821-S DO3316-683
www.ti.com
LM2674
FIGURE 8. Inductor Manufacturers' Part Numbers
Coilcraft Inc.
Coilcraft Inc., Europe
Pulse Engineering Inc.
Phone
(800) 322-2645
FAX
(708) 639-1469
Phone
+44 1236 730 595
FAX
+44 1236 730 627
Phone
(619) 674-8100
FAX
(619) 674-8262
Pulse Engineering Inc.,
Phone
+353 93 24 107
Europe
FAX
+353 93 24 459
Renco Electronics Inc.
Phone
(800) 645-5828
FAX
(516) 586-5562
Phone
(612) 475-1173
FAX
(612) 475-1786
Schott Corp.
FIGURE 9. Inductor Manufacturers' Phone Numbers
Output Capacitor
Output
Voltage
(V)
3.3
5.0
12
Inductance
(μH)
Surface Mount
Sprague
594D Series
Through Hole
AVX TPS
Series
Sanyo OS-CON
SA Series
Sanyo MV-GX
Series
Panasonic
HFQ Series
(μF/V)
(μF/V)
(μF/V)
(μF/V)
(μF/V)
(μF/V)
22
120/6.3
100/10
100/10
330/35
330/35
330/35
33
120/6.3
100/10
68/10
220/35
220/35
220/35
47
68/10
100/10
68/10
150/35
150/35
150/35
68
120/6.3
100/10
100/10
120/35
120/35
120/35
100
120/6.3
100/10
100/10
120/35
120/35
120/35
150
120/6.3
100/10
100/10
120/35
120/35
120/35
22
100/16
100/10
100/10
330/35
330/35
330/35
33
68/10
10010
68/10
220/35
220/35
220/35
47
68/10
100/10
68/10
150/35
150/35
150/35
68
100/16
100/10
100/10
120/35
120/35
120/35
100
100/16
100/10
100/10
120/35
120/35
120/35
150
100/16
100/10
100/10
120/35
120/35
120/35
22
120/20
(2×) 68/20
68/20
330/35
330/35
330/35
33
68/25
68/20
68/20
220/35
220/35
220/35
47
47/20
68/20
47/20
150/35
150/35
150/35
68
47/20
68/20
47/20
120/35
120/35
120/35
100
47/20
68/20
47/20
120/35
120/35
120/35
150
47/20
68/20
47/20
120/35
120/35
120/35
220
47/20
68/20
47/20
120/35
120/35
120/35
FIGURE 10. Output Capacitor Table
Nichicon Corp.
Panasonic
AVX Corp.
www.ti.com
Nichicon
PL Series
Phone
(847) 843-7500
FAX
(847) 843-2798
Phone
(714) 373-7857
FAX
(714) 373-7102
Phone
(845) 448-9411
14
Sanyo Corp.
(845) 448-1943
Phone
(207) 324-4140
FAX
(207) 324-7223
Phone
(619) 661-6322
FAX
(619) 661-1055
LM2674
Sprague/Vishay
FAX
FIGURE 11. Capacitor Manufacturers' Phone Numbers
500mA Diodes
3A Diodes
VR
Surface
Mount
Through
Hole
Surface
Mount
Through
Hole
20V
SK12
1N5817
SK32
1N5820
B120
SR102
SK13
1N5818
SK33
1N5821
30WQ03F
31DQ03
SK34
1N5822
30V
40V
SR302
B130
11DQ03
MBRS130
SR103
SK14
1N5819
B140
11DQ04
30BQ040
MBR340
MBRS140
SR104
30WQ04F
31DQ04
10BQ040
MBRS340
SR304
10MQ040
MBRD340
15MQ040
50V
SK15
MBR150
SK35
MBR350
B150
11DQ05
30WQ05F
31DQ05
10BQ050
SR105
SR305
FIGURE 12. Schottky Diode Selection Table
International Rectifier
Corp.
Motorola, Inc.
General Instruments
Corp.
Diodes, Inc.
Phone
(310) 322-3331
FAX
(310) 322-3332
Phone
(800) 521-6274
FAX
(602) 244-6609
Phone
(516) 847-3000
FAX
(516) 847-3236
Phone
(805) 446-4800
FAX
(805) 446-4850
FIGURE 13. Diode Manufacturers' Phone Numbers
15
www.ti.com
LM2674
10004130
FIGURE 14. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical)
AVX TPS
Recommended
Application Voltage
Voltage
Rating
+85°C Rating
3.3
6.3
5
10
10
20
12
25
15
35
Sprague 594D
Recommended
Application Voltage
Voltage
Rating
+85°C Rating
2.5
4
3.3
6.3
5
10
8
16
12
20
18
25
24
35
29
50
FIGURE 15. Recommended Application Voltage for AVX TPS and
Sprague 594D Tantalum Chip Capacitors Derated for 85°C.
www.ti.com
16
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to be
used with the SIMPLE SWITCHER line of switching regulators.
LM267X Made Simple (version 6.0) is available for use on
Windows 3.1, NT, or 95 operating systems.
Given:
Given:
VOUT = Regulated Output Voltage
VOUT = 20V
VIN(max) = Maximum Input Voltage
VIN(max) = 28V
ILOAD(max) = Maximum Load Current
ILOAD(max) = 500 mA
F = Switching Frequency (Fixed at a nominal 260 kHz).
F = Switching Frequency (Fixed at a nominal 260 kHz).
1. Programming Output Voltage (Selecting R1 and R2, as shown 1. Programming Output Voltage (Selecting R1 and R2, as shown
in Figure 3)
in Figure 3)
Use the following formula to select the appropriate resistor values. Select R1 to be 1 kΩ, 1%. Solve for R2.
where VREF = 1.21V
Select a value for R1 between 240Ω and 1.5 kΩ. The lower resistor R2 = 1k (16.53 − 1) = 15.53 kΩ, closest 1% value is 15.4 kΩ.
values minimize noise pickup in the sensitive feedback pin. (For the R2 = 15.4 kΩ.
lowest temperature coefficient and the best stability with time, use
1% metal film resistors.)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant E • T (V •
μs), from the following formula:
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant (E • T),
where VSAT=internal switch saturation voltage=0.25V and VD =
diode forward voltage drop = 0.5V
B. Use the E • T value from the previous formula and match it with B. E • T = 21.6 (V • μs)
the E • T number on the vertical axis of the Inductor Value Selection
Guide shown in Figure 7.
C. On the horizontal axis, select the maximum load current.
C. ILOAD(max) = 500 mA
D. Identify the inductance region intersected by the E • T value and D. From the inductor value selection guide shown in Figure 7, the
the Maximum Load Current value. Each region is identified by an inductance region intersected by the 21.6 (V • μs) horizontal line
inductance value and an inductor code (LXX).
and the 500mA vertical line is 100 μH, and the inductor code is L20.
E. Select an appropriate inductor from the four manufacturer's part E. From the table in Figure 8, locate line L20, and select an inductor
numbers listed in Figure 8. For information on the different types of part number from the list of manufacturers part numbers.
inductors, see the inductor selection in the fixed output voltage
design procedure.
3. Output Capacitor Selection (COUT)
3. Output Capacitor SeIection (COUT)
A. Select an output capacitor from the capacitor code selection
A. Use the appropriate row of the capacitor code selection guide,
guide in Figure 16. Using the inductance value found in the inductor in Figure 16. For this example, use the 15–20V row. The capacitor
selection guide, step 1, locate the appropriate capacitor code
code corresponding to an inductance of 100 μH is C20.
corresponding to the desired output voltage.
17
www.ti.com
LM2674
LM2674 Series Buck Regulator Design Procedure (Adjustable Output)
LM2674
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
B. Select an appropriate capacitor value and voltage rating, using
the capacitor code, from the output capacitor selection table in
Figure 17. There are two solid tantalum (surface mount) capacitor
manufacturers and four electrolytic (through hole) capacitor
manufacturers to choose from. It is recommended that both the
manufacturers and the manufacturer's series that are listed in the
table be used. A table listing the manufacturers' phone numbers is
located in Figure 11.
B. From the output capacitor selection table in Figure 17, choose
a capacitor value (and voltage rating) that intersects the capacitor
code(s) selected in section A, C20.
The capacitance and voltage rating values corresponding to the
capacitor code C20 are the:
Surface Mount:
33 μF/25V Sprague 594D Series.
33 μF/25V AVX TPS Series.
Through Hole:
33 μF/25V Sanyo OS-CON SC Series.
120 μF/35V Sanyo MV-GX Series.
120 μF/35V Nichicon PL Series.
120 μF/35V Panasonic HFQ Series.
Other manufacturers or other types of capacitors may also be used,
provided the capacitor specifications (especially the 100 kHz ESR)
closely match the characteristics of the capacitors listed in the
output capacitor table. Refer to the capacitor manufacturers' data
sheet for this information.
4. Catch Diode Selection (D1)
4. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. Schottky diodes provide
the load current times the catch diode duty cycle, 1-D (D is the
the best performance, and in this example a 500mA, 40V Schottky
switch duty cycle, which is approximately VOUT/VIN). The largest diode would be a good choice. If the circuit must withstand a
value of the catch diode average current occurs at the maximum continuous shorted output, a higher current (at least 1.2A) Schottky
input voltage (minimum D). For normal operation, the catch diode diode is recommended.
current rating must be at least 1.3 times greater than its maximum
average current. However, if the power supply design must
withstand a continuous output short, the diode should have a
current rating greater than the maximum current limit of the
LM2674. The most stressful condition for this diode is a shorted
output condition.
B. The reverse voltage rating of the diode should be at least 1.25
times the maximum input voltage.
C. Because of their fast switching speed and low forward voltage
drop, Schottky diodes provide the best performance and efficiency.
The Schottky diode must be located close to the LM2674 using
short leads and short printed circuit traces.
www.ti.com
18
EXAMPLE (Adjustable Output Voltage Version)
5. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. This capacitor should be
located close to the IC using short leads. In addition, the RMS
current rating of the input capacitor should be selected to be at least
½ the DC load current. The capacitor manufacturer data sheet must
be checked to assure that this current rating is not exceeded. The
curves shown in Figure 14 show typical RMS current ratings for
several different aluminum electrolytic capacitor values. A parallel
connection of two or more capacitors may be required to increase
the total minimum RMS current rating to suit the application
requirements.
For an aluminum electrolytic capacitor, the voltage rating should be
at least 1.25 times the maximum input voltage. Caution must be
exercised if solid tantalum capacitors are used. The tantalum
capacitor voltage rating should be twice the maximum input
voltage. The tables in Figure 15 show the recommended
application voltage for AVX TPS and Sprague 594D tantalum
capacitors. It is also recommended that they be surge current
tested by the manufacturer. The TPS series available from AVX,
and the 593D and 594D series from Sprague are all surge current
tested. Another approach to minimize the surge current stresses
on the input capacitor is to add a small inductor in series with the
input supply line.
Use caution when using only ceramic capacitors for input
bypassing, because it may cause severe ringing at the VIN pin.
5. Input Capacitor (CIN)
The important parameters for the input capacitor are the input
voltage rating and the RMS current rating. With a maximum input
voltage of 28V, an aluminum electrolytic capacitor with a voltage
rating of at least 35V (1.25 × VIN) would be needed.
The RMS current rating requirement for the input capacitor in a
buck regulator is approximately ½ the DC load current. In this
example, with a 500mA load, a capacitor with an RMS current rating
of at least 250 mA is needed. The curves shown in Figure 14 can
be used to select an appropriate input capacitor. From the curves,
locate the 35V line and note which capacitor values have RMS
current ratings greater than 250 mA.
For a through hole design, a 68 μF/35V electrolytic capacitor
(Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
equivalent) would be adequate. Other types or other
manufacturers' capacitors can be used provided the RMS ripple
current ratings are adequate. Additionally, for a complete surface
mount design, electrolytic capacitors such as the Sanyo CV-C or
CV-BS, and the Nichicon WF or UR and the NIC Components
NACZ series could be considered.
For surface mount designs, solid tantalum capacitors can be used,
but caution must be exercised with regard to the capacitor surge
current rating and voltage rating. In this example, checking Figure
15, and the Sprague 594D series datasheet, a Sprague 594D 15
μF, 50V capacitor is adequate.
6. Boost Capacitor (CB)
6. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch
gate on fully. All applications should use a 0.01 μF, 50V ceramic
capacitor.
For this application, and all applications, use a 0.01 μF, 50V
ceramic capacitor.
Inductance (μH)
Case
Style (Note 8)
Output
Voltage (V)
22
33
47
68
100
150
220
SM and TH
1.21–2.50
—
—
—
—
C1
C2
C3
SM and TH
2.50–3.75
—
—
—
C1
C2
C3
C3
SM and TH
3.75–5.0
—
—
C4
C5
C6
C6
C6
SM and TH
5.0–6.25
—
C4
C7
C6
C6
C6
C6
SM and TH
6.25–7.5
C8
C4
C7
C6
C6
C6
C6
SM and TH
7.5–10.0
C9
C10
C11
C12
C13
C13
C13
SM and TH
10.0–12.5
C14
C11
C12
C12
C13
C13
C13
SM and TH
12.5–15.0
C15
C16
C17
C17
C17
C17
C17
SM and TH
15.0–20.0
C18
C19
C20
C20
C20
C20
C20
SM and TH
20.0–30.0
C21
C22
C22
C22
C22
C22
C22
TH
30.0–37.0
C23
C24
C24
C25
C25
C25
C25
Note 8: SM - Surface Mount, TH - Through Hole
FIGURE 16. Capacitor Code Selection Guide
19
www.ti.com
LM2674
PROCEDURE (Adjustable Output Voltage Version)
LM2674
Output Capacitor
Surface Mount
Through Hole
Cap.
Ref.
Desg.
#
Sprague
594D Series
AVX TPS
Series
Sanyo OS-CON
SA Series
Sanyo MV-GX
Series
Nichicon
PL Series
Panasonic
HFQ Series
(μF/V)
(μF/V)
(μF/V)
(μF/V)
(μF/V)
(μF/V)
C1
120/6.3
100/10
100/10
220/35
220/35
220/35
C2
120/6.3
100/10
100/10
150/35
150/35
150/35
C3
120/6.3
100/10
100/35
120/35
120/35
120/35
C4
68/10
100/10
68/10
220/35
220/35
220/35
C5
100/16
100/10
100/10
150/35
150/35
150/35
C6
100/16
100/10
100/10
120/35
120/35
120/35
C7
68/10
100/10
68/10
150/35
150/35
150/35
C8
100/16
100/10
100/10
330/35
330/35
330/35
C9
100/16
100/16
100/16
330/35
330/35
330/35
C10
100/16
100/16
68/16
220/35
220/35
220/35
C11
100/16
100/16
68/16
150/35
150/35
150/35
C12
100/16
100/16
68/16
120/35
120/35
120/35
C13
100/16
100/16
100/16
120/35
120/35
120/35
C14
100/16
100/16
100/16
220/35
220/35
220/35
C15
47/20
68/20
47/20
220/35
220/35
220/35
C16
47/20
68/20
47/20
150/35
150/35
150/35
C17
47/20
68/20
47/20
120/35
120/35
120/35
C18
68/25
(2×) 33/25
47/25 (Note 9)
220/35
220/35
220/35
C19
33/25
33/25
33/25 (Note 9)
150/35
150/35
150/35
C20
33/25
33/25
33/25 (Note 9)
120/35
120/35
120/35
C21
33/35
(2×) 22/25
(Note 10)
150/35
150/35
150/35
C22
33/35
22/35
(Note 10)
120/35
120/35
120/35
C23
(Note 10)
(Note 10)
(Note 10)
220/50
100/50
120/50
C24
(Note 10)
(Note 10)
(Note 10)
150/50
100/50
120/50
C25
(Note 10)
(Note 10)
(Note 10)
150/50
82/50
82/50
Note 9: The SC series of Os-Con capacitors (others are SA series)
Note 10: The voltage ratings of the surface mount tantalum chip and Os-Con capacitors are too low to work at these voltages.
FIGURE 17. Output Capacitor Selection Table
www.ti.com
20
LM2674
Application Information
TYPICAL SURFACE MOUNT PC BOARD LAYOUT, FIXED
OUTPUT (4X SIZE)
10004136
CIN - 15 μF, 25V, Solid Tantalum Sprague, “594D series”
COUT - 68 μF, 10V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 47 μH, L13, Coilcraft DO3308
CB - 0.01 μF, 50V, Ceramic
TYPICAL SURFACE MOUNT PC BOARD LAYOUT,
ADJUSTABLE OUTPUT (4X SIZE)
10004137
CIN - 15 μF, 50V, Solid Tantalum Sprague, “594D series”
COUT - 33 μF, 25V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 100 μH, L20, Coilcraft DO3316
CB - 0.01 μF, 50V, Ceramic
R1 - 1k, 1%
R2 - Use formula in Design Procedure
FIGURE 18. PC Board Layout
21
www.ti.com
LM2674
Layout is very important in switching regulator designs.
Rapidly switching currents associated with wiring inductance
can generate voltage transients which can cause problems.
For minimal inductance and ground loops, the wires indicated
by heavy lines (in Figure 2 and Figure 3) should be wide
printed circuit traces and should be kept as short as possible. For best results, external components should be located as close to the switcher IC as possible using ground plane
construction or single point grounding.
If open core inductors are used, special care must be taken
as to the location and positioning of this type of inductor. Allowing the inductor flux to intersect sensitive feedback, IC
ground path, and COUT wiring can cause problems.
When using the adjustable version, special care must be taken as to the location of the feedback resistors and the asso-
www.ti.com
ciated wiring. Physically locate both resistors near the IC, and
route the wiring away from the inductor, especially an open
core type of inductor.
LLP Package Devices
The LM2674 is offered in the 16 lead LLP surface mount
package to allow for increased power dissipation compared
to the SO-8 and DIP.
The Die Attach Pad (DAP) can and should be connected to
PCB Ground plane/island. For CAD and assembly guidelines
refer
to
Application
Note
AN-1187
at
http://
power.national.com.
22
LM2674
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead (0.150″ Wide) Molded Small Outline Package, JEDEC
Order Number LM2674M-3.3, LM2674M-5.0,
LM2674M-12 or LM2674M-ADJ
NS Package Number M08A
23
www.ti.com
LM2674
8-Lead (0.300″ Wide) Molded Dual-In-Line Package
Order Number LM2674N-3.3, LM2674N-5.0,
LM2674N-12 or LM2674N-ADJ
NS Package Number N08E
16-Lead LLP Surface Mount Package
NS Package Number LDA16A
www.ti.com
24
LM2674
25
www.ti.com
LM2674 SIMPLE SWITCHER Power Converter High Efficiency 500 mA Step-Down Voltage
Regulator
Notes
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated