Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
LM26LV and LM26LV-Q1 1.6-V, WSON-6 Factory Preset Temperature Switch and
Temperature Sensor
1 Features
3 Description
•
•
•
The LM26LV and LM26LV-Q1 are low-voltage,
precision, dual-output, low-power temperature
switches and temperature sensors. The temperature
trip point (TTRIP) can be preset at the factory to any
temperature in the range of 0°C to 150°C in 1°C
increments. Built-in temperature hysteresis (THYST)
keeps the output stable in an environment of
temperature instability.
1
•
•
•
•
•
•
•
Low 1.6-V Operation
Low Quiescent Current
Latching Function: Device Can Latch the Over
Temperature Condition
Push-Pull and Open-Drain Temperature Switch
Outputs
Wide Trip Point Range of 0°C to 150°C
Very Linear Analog VTEMP Temperature Sensor
Output
VTEMP Output Short-Circuit Protected
Accurate Over –50°C to 150°C Temperature
Range
Excellent Power Supply Noise Rejection
LM26LVQISD-130 and LM26LVQISD-135 are
AEC-Q100 Qualified and are Manufactured on an
Automotive Grade Flow:
– Device Temperature Grade 0: –40°C to 150°C
Ambient Operating Temperature Range
– Device HBM ESD Classification Level 3 A
– Device CDM ESD Classification Level C6
– Device MM ESD Classification Level M3
2 Applications
•
•
•
•
•
•
Cell Phones and Wireless Transceivers
Digital Cameras
Battery Management Systems
Automotive Applications
Disk Drives
Games and Appliances
In normal operation the LM26LV or LM26LV-Q1
temperature switch outputs assert when the die
temperature exceeds TTRIP. The temperature switch
outputs will reset when the temperature falls below a
temperature equal to (TTRIP – THYST). The
OVERTEMP digital output, is active-high with a pushpull structure, while the OVERTEMP digital output, is
active-low with an open-drain structure.
The analog output, VTEMP, delivers an analog output
voltage with Negative Temperature Coefficient (NTC).
Driving the TRIP_TEST input high causes the digital
outputs to be asserted for in-situ verification and
causes the threshold voltage to appear at the VTEMP
output pin, which could be used to verify the
temperature trip point.
The LM26LV's and LM26LV-Q1's low minimum
supply voltage makes them ideal for 1.8-V system
designs. The wide operating range, low supply
current, and excellent accuracy provide a
temperature switch solution for a wide range of
commercial and industrial applications.
Device Information(1)
PART NUMBER
LM26LV, LM26LV-Q1
PACKAGE
WSON (6)
BODY SIZE (NOM)
2.20 mm × 2.50 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Redundant Protection and Monitoring
VDD Supply
(+1.6V to +5.5V)
Example: 2 to 3
Battery Cells
VDD
VTEMP
LM26LV
Analog
Typical Transfer Characteristic
ADC Input
Microcontroller
OVERTEMP
OVERTEMP
TRIP TEST
GND
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
4
4
4
4
5
5
6
7
9
Absolute Maximum Ratings ......................................
ESD Ratings: LM26LV ..............................................
ESD Ratings: LM26LV-Q1 ........................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Accuracy Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
7.1 Overview ................................................................. 12
7.2 Functional Block Diagram ....................................... 12
7.3 Feature Description................................................. 13
7.4 Device Functional Modes........................................ 21
8
Application and Implementation ........................ 23
8.1 Application Information............................................ 23
8.2 Typical Application .................................................. 23
9
Power Supply Recommendations...................... 25
9.1 Power Supply Noise Immunity ................................ 25
10 Layout................................................................... 25
10.1 Layout Guidelines ................................................. 25
10.2 Layout Example .................................................... 26
11 Device and Documentation Support ................. 27
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
27
27
27
27
27
27
27
12 Mechanical, Packaging, and Orderable
Information ........................................................... 27
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (February 2013) to Revision G
Page
•
Added Device Information table, Pin Configuration and Functions section, Specifications section, ESD Ratings table,
Thermal Information table, Switching Characteristics table, Detailed Description section, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section................................................................ 1
•
Updated values in the Thermal Information table to align with JEDEC standards................................................................. 5
Changes from Revision E (February 2013) to Revision F
•
2
Page
Changed layout of National Semiconductor Data Sheet to TI format .................................................................................... 1
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
5 Pin Configuration and Functions
NGF Package
6-Pin WSON
Top View
TRIP_TEST
1
GND
2
OVERTEMP
3
Thermal
Pad
6
VTEMP
5
OVERTEMP
4
VDD
Not to scale
Pin Functions
PIN
NAME
GND
NO.
2
TYPE
GND
EQUIVALENT
CIRCUIT
DESCRIPTION
Power supply ground
—
VDD
OVERTEMP
5
O
Overtemperature switch output. Active high, push-pull.
Asserted when the measured temperature exceeds the trip point temperature or
if TRIP_TEST = 1. This pin may be left open if not used.
GND
OVERTEMP
3
O
Overtemperature switch output. Active low, open-drain (See Determining the
Pullup Resistor Value).
Asserted when the measured temperature exceeds the trip point temperature or
if TRIP_TEST = 1. This pin may be left open if not used.
GND
VDD
TRIP_TEST
1
I
TRIP_TEST pin. Active high input.
If TRIP_TEST = 0 (Default) then: VTEMP = VTS, temperature sensor output
voltage.
If TRIP_TEST = 1 then: OVERTEMP and OVERTEMP outputs are asserted and
VTEMP = VTRIP, temperature trip voltage.
This pin may be left open if not used.
1 PA
GND
VDD
4
PWR
Positive supply voltage
—
VDD
VSENSE
VTEMP
6
O
VTEMP analog voltage output.
If TRIP_TEST = 0 then: VTEMP = VTS, temperature sensor output voltage.
If TRIP_TEST = 1 then: VTEMP = VTRIP, temperature trip voltage.
This pin may be left open if not used.
GND
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
3
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Pin Functions (continued)
PIN
NAME
NO.
Thermal Pad
—
TYPE
—
EQUIVALENT
CIRCUIT
DESCRIPTION
The best thermal conductivity between the device and the PCB is achieved by
soldering the DAP of the package to the thermal pad on the PCB. The thermal
pad can be a floating node. However, for improved noise immunity the thermal
pad must be connected to the circuit GND node, preferably directly to pin 2
(GND) of the device.
—
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
UNIT
Supply voltage
–0.3
6
V
Voltage at OVERTEMP pin
–0.3
6
V
Voltage at OVERTEMP and VTEMP pins
–0.3
VDD + 0.5
V
TRIP_TEST input voltage
–0.3
VDD + 0.5
V
–7
7
mA
Output current, any output pin
Input current at any pin (3)
Maximum junction temperature, TJ(MAX)
Storage temperature, Tstg
(1)
(2)
(3)
–65
5
mA
155
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
For soldering specifications, see Absolute Maximum Ratings for Soldering.
When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > VDD), the current at that pin must be limited to 5 mA.
6.2 ESD Ratings: LM26LV
VALUE
V(ESD)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±4500
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±1000
Machine model (MM)
(1)
(2)
(3)
(3)
UNIT
V
±300
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
The machine model (MM) is a 200-pF capacitor charged to the specified voltage then discharged directly into each pin.
6.3 ESD Ratings: LM26LV-Q1
VALUE
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002 (1)
±4500
Charged-device model (CDM), per AEC Q100-011
±1000
Machine model (MM)
±300
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.4 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VDD
Supply voltage
1.6
Supply current
TA
4
MAX
5.5
8
Specified ambient temperature
Submit Documentation Feedback
NOM
–50
UNIT
V
µA
150
°C
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
6.5 Thermal Information
THERMAL METRIC
(1)
LM26LV and
LM26LV-Q1
UNIT
NGF (WSON)
6 PINS
RθJA
Junction-to-ambient thermal resistance
100.7
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
121.7
°C/W
RθJB
Junction-to-board thermal resistance
70
°C/W
ψJT
Junction-to-top characterization parameter
7.1
°C/W
ψJB
Junction-to-board characterization parameter
70.3
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
15.9
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.6 Electrical Characteristics
Typical values apply for TA = TJ = 25°C; minimum and maximum limits apply for TA = TJ = –50°C to 150°C,
VDD = 1.6 V to 5.5 V (unless otherwise noted). (1) (2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GENERAL SPECIFICATIONS
IS
Quiescent power supply current
Hysteresis
4.5
8
16
µA
5
5.5
°C
OVERTEMP DIGITAL OUTPUT—ACTIVE HIGH, PUSH-PULL
VOH
Logic High output voltage
VDD ≥ 1.6 V, Source ≤ 340 µA
VDD – 0.2
VDD ≥ 2 V, Source ≤ 498 µA
VDD – 0.2
VDD ≥ 3.3 V, Source ≤ 780 µA
VDD – 0.2
VDD ≥ 1.6 V, Source ≤ 600 µA
VDD – 0.45
VDD ≥ 2 V, Source ≤ 980 µA
VDD – 0.45
VDD ≥ 3.3 V, Source ≤ 1.6 mA
VDD – 0.45
V
BOTH OVERTEMP AND OVERTEMP DIGITAL OUTPUTS
VOL
Logic Low output voltage
VDD ≥ 1.6 V, Source ≤ 385 µA
0.2
VDD ≥ 2 V, Source ≤ 500 µA
0.2
VDD ≥ 3.3 V, Source ≤ 730 µA
0.2
VDD ≥ 1.6 V, Source ≤ 690 µA
0.45
VDD ≥ 2 V, Source ≤ 1.05 mA
0.45
VDD ≥ 3.3 V, Source ≤ 1.62 mA
0.45
V
OVERTEMP DIGITAL OUTPUT—ACTIVE LOW, OPEN DRAIN
IOH
(1)
(2)
(3)
Logic High output leakage
current (3)
TA = 30°C
0.001
1
TA = 150°C
0.025
1
µA
Limits are specified to TI's AOQL (Average Outgoing Quality Level).
Typical values apply for TJ = TA = 25°C and represent most likely parametric norm.
The 1-µA limit is based on a testing limitation and does not reflect the actual performance of the part. Expect to see a doubling of the
current for every 15°C increase in temperature. For example, the 1-nA typical current at 25°C would increase to 16 nA at 85°C.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
5
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Electrical Characteristics (continued)
Typical values apply for TA = TJ = 25°C; minimum and maximum limits apply for TA = TJ = –50°C to 150°C,
VDD = 1.6 V to 5.5 V (unless otherwise noted).(1)(2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VTEMP ANALOG TEMPERATURE SENSOR OUTPUT
Gain 1 (trip point = 0°C to 69°C)
VTEMP sensor gain
–5.1
Gain 2 (trip point = 70°C to 109°C)
–7.7
Gain 3 (trip point = 110°C to 129°C)
–10.3
Gain 4 (trip point = 130°C to 150°C)
–12.8
1.6 V ≤ VDD < 1.8 V
Source ≤ 90 µA,
VDD – VTEMP ≥ 200 mV
–1
Sink ≤ 100 µA, VTEMP ≥ 260 mV
VTEMP load regulation
(4)
VDD ≥ 1.8 V
–0.1
0.1
Source ≤ 120 µA,
VDD – VTEMP ≥ 200 mV
–1
Sink ≤ 200 µA, VTEMP ≥ 260 mV
mV/°C
1
0.1
Source or sink = 100 µA
1
1
Ω
0.29
Supply to VTEMP DC line
regulation (5)
CL
VTEMP output load capacitance
VDD = 1.6 V to 5.5 V
Without series resistor. See Capacitive Loads.
mV
–0.1
mV
74
µV/V
–82
dB
1100
pF
TRIP_TEST DIGITAL INPUT
VIH
Logic High threshold voltage
VIL
Logic Low threshold voltage
IIH
Logic High input current
IIL
Logic Low input current (3)
(4)
(5)
VDD – 0.5
V
0.5
1.5
2.5
µA
0.001
1
µA
Source currents are flowing out of the LM26LV or LM26LV-Q1. Sink currents are flowing into the LM26LV or LM26LV-Q1.
Line regulation (DC) is calculated by subtracting the output voltage at the highest supply voltage from the output voltage at the lowest
supply voltage. The typical DC line regulation specification does not include the output voltage shift discussed in Voltage Shift.
6.7 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
tEN
Time from power ON to digital output enabled (1)
tVTEMP
Time from power ON to analog temperature valid (1)
(1)
6
CL = 0 pF to 1100 pF
MIN
TYP
MAX
1.1
2.3
UNIT
ms
1
2.9
ms
Figure 1 and Figure 2 show the definitions of tEN and tVTEMP.
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
6.8 Accuracy Characteristics
See
(1)
PARAMETER
TEST CONDITIONS
MIN
MAX
–2.2
2.2
–1.8
1.8
UNIT
TRIP POINT ACCURACY
Trip point accuracy (2)
TA = 0°C to 150°C, VDD = 5 V
°C
VTEMP ANALOG TEMPERATURE SENSOR OUTPUT ACCURACY (3)
TA = 20°C to 40°C, VDD = 1.6 V to 5.5 V
Gain 1
trip point = 0°C to 69°C
Gain 2
trip point = 70°C to 109°C
VTEMP temperature accuracy (2)
Gain 3
trip point = 110°C to 129°C
Gain 4
trip point = 130°C to 150°C
(1)
(2)
(3)
TA = 0°C to 70°C, VDD = 1.6 V to 5.5 V
–2
2
TA = 0°C to 90°C, VDD = 1.6 V to 5.5 V
–2.1
2.1
TA = 0°C to 120°C, VDD = 1.6 V to 5.5 V
–2.2
2.2
TA = 0°C to 150°C, VDD = 1.6 V to 5.5 V
–2.3
2.3
TA = –50°C to 0°C, VDD = 1.7 V to 5.5 V
–1.7
1.7
TA = 20°C to 40°C, VDD = 1.8 V to 5.5 V
–1.8
1.8
TA = 0°C to 70°C, VDD = 1.9 V to 5.5 V
–2
2
TA = 0°C to 90°C, VDD = 1.9 V to 5.5 V
–2.1
2.1
TA = 0°C to 120°C, VDD = 1.9 V to 5.5 V
–2.2
2.2
TA = 0°C to 150°C, VDD = 1.9 V to 5.5 V
–2.3
2.3
TA = –50°C to 0°C, VDD = 2.3 V to 5.5 V
–1.7
1.7
TA = 20°C to 40°C, VDD = 2.3 V to 5.5 V
–1.8
1.8
TA = 0°C to 70°C, VDD = 2.5 V to 5.5 V
–2
2
TA = 0°C to 90°C, VDD = 2.5 V to 5.5 V
–2.1
2.1
TA = 0°C to 120°C, VDD = 2.5 V to 5.5 V
–2.2
2.2
TA = 0°C to 150°C, VDD = 2.5 V to 5.5 V
–2.3
2.3
TA = –50°C to 0°C, VDD = 3 V to 5.5 V
–1.7
1.7
TA = 20°C to 40°C, VDD = 2.7 V to 5.5 V
–1.8
1.8
TA = 0°C to 70°C, VDD = 3 V to 5.5 V
–2
2
TA = 0°C to 90°C, VDD = 3 V to 5.5 V
–2.1
2.1
TA = 0°C to 120°C, VDD = 3 V to 5.5 V
–2.2
2.2
TA = 0°C to 150°C, VDD = 3 V to 5.5 V
–2.3
2.3
TA = –50°C to 0°C, VDD = 3.6 V to 5.5 V
–1.7
1.7
°C
Limits are specified to TI's AOQL (Average Outgoing Quality Level).
Accuracy is defined as the error between the measured and reference output voltages, tabulated in Table 1 at the specified conditions of
supply gain setting, voltage, and temperature (°C). Accuracy limits include line regulation within the specified conditions. Accuracy limits
do not include load regulation; they assume no DC load.
Changes in output due to self heating can be computed by multiplying the internal dissipation by the temperature thermal resistance.
VDD
1.3V
tEN
OVERTEMP
OVERTEMP
Enabled
Enabled
Figure 1. Definition of tEN
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
7
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
VDD
tVTEMP
Valid
VTEMP
Figure 2. Definition of tVTEMP
8
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
6.9 Typical Characteristics
Figure 3. VTEMP Output Temperature Error vs Temperature
Figure 4. Minimum Operating Temperature
vs Supply Voltage
Figure 5. Supply Current vs Temperature
Figure 6. Supply Current vs Supply Voltage
100-mV overhead
TA = 80°C
Sourcing current
Figure 7. Load Regulation
(1)
200-mV overhead
(1)
TA = 80°C
Figure 8. Load Regulation
Sourcing Current
(1)
The curves shown represent typical performance under worst-case conditions. Performance improves with larger VTEMP, larger VDD, and
lower temperatures.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
9
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
400-mV overhead
TA = 80°C
Sourcing current
Figure 9. Load Regulation
VDD = 1.6 V
Sinking Current
10
VDD = 2.4 V
Figure 10. Load Regulation
(1)
Sourcing current
(1)
Sinking Current
Figure 12. Load Regulation(1)
Sinking Current
Figure 13. Load Regulation(1)
(1)
TA = 150°C
VDD = 1.8 V
Figure 11. Load Regulation
VDD = 2.4 V
1.72-V overhead
(1)
Figure 14. Change in VTEMP vs Overhead Voltage
The curves shown represent typical performance under worst-case conditions. Performance improves with larger VTEMP, larger VDD, and
lower temperatures.
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
Typical Characteristics (continued)
Gain 1 (Trip Points = 0°C tp 69°C)
Figure 15. VTEMP Supply-Noise Rejection vs Frequency
Gain 2 (Trip Points = 70°C to 109°C)
Figure 16. Line Regulation VTEMP vs Supply Voltage
Gain 3 (Trip Points = 110°C to 129°C)
Figure 17. Line Regulation VTEMP vs Supply Voltage
Figure 18. Line Regulation VTEMP vs Supply Voltage
Gain 4 (Trip Points = 130°C to 150°C)
Figure 19. Line Regulation VTEMP vs Supply Voltage
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
11
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
7 Detailed Description
7.1 Overview
The LM26LV and LM26LV-Q1 are precision, dual-output, temperature switches with analog temperature sensor
output. The trip temperature (TTRIP) is factory selected by the order number. The VTEMP class AB analog output
provides a voltage that is proportional to temperature. The LM26LV and LM26LV-Q1 include an internal
reference DAC (TEMP THRESHOLD), analog temperature sensor and analog comparator. The reference DAC is
connected to one of the comparator inputs. The reference DAC output voltage (VTRIP) is preprogrammed by TI.
The result of the reference DAC voltage and the temperature sensor output comparison is provided on two
output pins OVERTEMP and OVERTEMP.
The VTEMP output has a programmable gain. The output gain has 4 possible settings as described in Table 1.
The gain setting is dependent on the temperature trip point selected.
Built-in temperature hysteresis (THYST) prevents the digital outputs from oscillating. The OVERTEMP and
OVERTEMP activates when the die temperature exceeds TTRIP and releases when the temperature falls below a
temperature equal to TTRIP minus THYST. OVERTEMP is active-high with a push-pull structure. OVERTEMP, is
active-low with an open-drain structure. The comparator hysteresis is fixed at 5°C.
Driving the TRIP-TEST high activates the digital outputs. A processor can check the logic level of the
OVERTEMP or OVERTEMP, confirming that they changed to their active state. This allows for system
production testing verification that the comparator and output circuitry are functional after system assembly.
When the TRIP-TEST pin is high, the trip-level reference voltage appears at the VTEMP pin. Tying OVERTEMP to
TRIP-TEST latches the output after it trips. It can be cleared by forcing TRIP-TEST low or powering off the
LM26LV or LM26LV-Q1.
7.2 Functional Block Diagram
VDD
4
TRIP TEST = 0
(Default)
LM26LV
6
TRIP TEST = 1
VTS
3
VTEMP
OVERTEMP
VTRIP
VDD
TEMP
SENSOR
TEMP
THRESHOLD
5
2
GND
OVERTEMP
1
TRIP
TEST
Copyright © 2016, Texas Instruments Incorporated
12
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
7.3 Feature Description
7.3.1 LM26LV and LM26LV-Q1 VTEMP vs Die Temperature Conversion Table
The LM26LV and LM26LV-Q1 have one out of four possible factory-set gains, Gain 1 through Gain 4, depending
on the range of the Temperature Trip Point. The VTEMP temperature sensor voltage, in millivolts, at each discrete
die temperature over the complete operating temperature range, and for each of the four Temperature Trip Point
ranges, is shown in Table 1. This table is the reference from which the LM26LV and LM26LV-Q1 accuracy
specifications (listed in Accuracy Characteristics) are determined. This table can be used, for example, in a host
processor look-up table. See The Second-Order Equation (Parabolic) for the parabolic equation used in the
Conversion Table.
Table 1. VTEMP Temperature Sensor Output Voltage vs Die Temperature Conversion Table
DIE TEMPERATURE (°C)
(1)
ANALOG OUTPUT VOLTAGE, VTEMP (mV) (1)
GAIN 1
GAIN 2
GAIN 3
GAIN 4
–50
1312
1967
2623
3278
–49
1307
1960
2613
3266
–48
1302
1952
2603
3253
–47
1297
1945
2593
3241
–46
1292
1937
2583
3229
–45
1287
1930
2573
3216
–44
1282
1922
2563
3204
–43
1277
1915
2553
3191
–42
1272
1908
2543
3179
–41
1267
1900
2533
3166
–40
1262
1893
2523
3154
–39
1257
1885
2513
3141
–38
1252
1878
2503
3129
–37
1247
1870
2493
3116
–36
1242
1863
2483
3104
–35
1237
1855
2473
3091
–34
1232
1848
2463
3079
–33
1227
1840
2453
3066
–32
1222
1833
2443
3054
–31
1217
1825
2433
3041
–30
1212
1818
2423
3029
–29
1207
1810
2413
3016
–28
1202
1803
2403
3004
–27
1197
1795
2393
2991
–26
1192
1788
2383
2979
–25
1187
1780
2373
2966
–24
1182
1773
2363
2954
–23
1177
1765
2353
2941
–22
1172
1757
2343
2929
–21
1167
1750
2333
2916
–20
1162
1742
2323
2903
–19
1157
1735
2313
2891
–18
1152
1727
2303
2878
–17
1147
1720
2293
2866
–16
1142
1712
2283
2853
–15
1137
1705
2272
2841
–14
1132
1697
2262
2828
–13
1127
1690
2252
2815
–12
1122
1682
2242
2803
VDD = 5 V. Values are bold for each gain's respective trip point range.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
13
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Feature Description (continued)
Table 1. VTEMP Temperature Sensor Output Voltage vs Die Temperature Conversion Table (continued)
DIE TEMPERATURE (°C)
14
ANALOG OUTPUT VOLTAGE, VTEMP (mV) (1)
GAIN 1
GAIN 2
GAIN 3
GAIN 4
–11
1116
1674
2232
2790
–10
1111
1667
2222
2777
–9
1106
1659
2212
2765
–8
1101
1652
2202
2752
–7
1096
1644
2192
2740
–6
1091
1637
2182
2727
–5
1086
1629
2171
2714
–4
1081
1621
2161
2702
–3
1076
1614
2151
2689
–2
1071
1606
2141
2676
–1
1066
1599
2131
2664
0
1061
1591
2121
2651
1
1056
1583
2111
2638
2
1051
1576
2101
2626
3
1046
1568
2090
2613
4
1041
1561
2080
2600
5
1035
1553
2070
2587
6
1030
1545
2060
2575
7
1025
1538
2050
2562
8
1020
1530
2040
2549
9
1015
1522
2029
2537
10
1010
1515
2019
2524
11
1005
1507
2009
2511
12
1000
1499
1999
2498
13
995
1492
1989
2486
14
990
1484
1978
2473
15
985
1477
1968
2460
16
980
1469
1958
2447
17
974
1461
1948
2435
18
969
1454
1938
2422
19
964
1446
1927
2409
20
959
1438
1917
2396
21
954
1431
1907
2383
22
949
1423
1897
2371
23
944
1415
1886
2358
24
939
1407
1876
2345
25
934
1400
1866
2332
26
928
1392
1856
2319
27
923
1384
1845
2307
28
918
1377
1835
2294
29
913
1369
1825
2281
30
908
1361
1815
2268
31
903
1354
1804
2255
32
898
1346
1794
2242
33
892
1338
1784
2230
34
887
1331
1774
2217
35
882
1323
1763
2204
36
877
1315
1753
2191
37
872
1307
1743
2178
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
Feature Description (continued)
Table 1. VTEMP Temperature Sensor Output Voltage vs Die Temperature Conversion Table (continued)
DIE TEMPERATURE (°C)
ANALOG OUTPUT VOLTAGE, VTEMP (mV) (1)
GAIN 1
GAIN 2
GAIN 3
GAIN 4
38
867
1300
1732
2165
39
862
1292
1722
2152
40
856
1284
1712
2139
41
851
1276
1701
2127
42
846
1269
1691
2114
43
841
1261
1681
2101
44
836
1253
1670
2088
45
831
1245
1660
2075
46
825
1238
1650
2062
47
820
1230
1639
2049
48
815
1222
1629
2036
49
810
1214
1619
2023
50
805
1207
1608
2010
51
800
1199
1598
1997
52
794
1191
1588
1984
53
789
1183
1577
1971
54
784
1176
1567
1958
55
779
1168
1557
1946
56
774
1160
1546
1933
57
769
1152
1536
1920
58
763
1144
1525
1907
59
758
1137
1515
1894
60
753
1129
1505
1881
61
748
1121
1494
1868
62
743
1113
1484
1855
63
737
1105
1473
1842
64
732
1098
1463
1829
65
727
1090
1453
1816
66
722
1082
1442
1803
67
717
1074
1432
1790
68
711
1066
1421
1776
69
706
1059
1411
1763
70
701
1051
1400
1750
71
696
1043
1390
1737
72
690
1035
1380
1724
73
685
1027
1369
1711
74
680
1019
1359
1698
75
675
1012
1348
1685
76
670
1004
1338
1672
77
664
996
1327
1659
78
659
988
1317
1646
79
654
980
1306
1633
80
649
972
1296
1620
81
643
964
1285
1607
82
638
957
1275
1593
83
633
949
1264
1580
84
628
941
1254
1567
85
622
933
1243
1554
86
617
925
1233
1541
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
15
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Feature Description (continued)
Table 1. VTEMP Temperature Sensor Output Voltage vs Die Temperature Conversion Table (continued)
DIE TEMPERATURE (°C)
16
ANALOG OUTPUT VOLTAGE, VTEMP (mV) (1)
GAIN 1
GAIN 2
GAIN 3
GAIN 4
87
612
917
1222
1528
88
607
909
1212
1515
89
601
901
1201
1501
90
596
894
1191
1488
91
591
886
1180
1475
92
586
878
1170
1462
93
580
870
1159
1449
94
575
862
1149
1436
95
570
854
1138
1422
96
564
846
1128
1409
97
559
838
1117
1396
98
554
830
1106
1383
99
549
822
1096
1370
100
543
814
1085
1357
101
538
807
1075
1343
102
533
799
1064
1330
103
527
791
1054
1317
104
522
783
1043
1304
105
517
775
1032
1290
106
512
767
1022
1277
107
506
759
1011
1264
108
501
751
1001
1251
109
496
743
990
1237
110
490
735
979
1224
111
485
727
969
1211
112
480
719
958
1198
113
474
711
948
1184
114
469
703
937
1171
115
464
695
926
1158
116
459
687
916
1145
117
453
679
905
1131
118
448
671
894
1118
119
443
663
884
1105
120
437
655
873
1091
121
432
647
862
1078
122
427
639
852
1065
123
421
631
841
1051
124
416
623
831
1038
125
411
615
820
1025
126
405
607
809
1011
127
400
599
798
998
128
395
591
788
985
129
389
583
777
971
130
384
575
766
958
131
379
567
756
945
132
373
559
745
931
133
368
551
734
918
134
362
543
724
904
135
357
535
713
891
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
Feature Description (continued)
Table 1. VTEMP Temperature Sensor Output Voltage vs Die Temperature Conversion Table (continued)
DIE TEMPERATURE (°C)
ANALOG OUTPUT VOLTAGE, VTEMP (mV) (1)
GAIN 1
GAIN 2
GAIN 3
GAIN 4
136
352
527
702
878
137
346
519
691
864
138
341
511
681
851
139
336
503
670
837
140
330
495
659
824
141
325
487
649
811
142
320
479
638
797
143
314
471
627
784
144
309
463
616
770
145
303
455
606
757
146
298
447
595
743
147
293
438
584
730
148
287
430
573
716
149
282
422
562
703
150
277
414
552
690
7.3.2 VTEMP vs Die Temperature Approximations
The LM26LV's and LM26LV-Q1's VTEMP analog temperature output is very linear. Table 1 and the equation in
The Second-Order Equation (Parabolic) represent the most accurate typical performance of the VTEMP voltage
output versus temperature.
7.3.2.1 The Second-Order Equation (Parabolic)
The data from Table 1, or Equation 1, when plotted, has an umbrella-shaped parabolic curve. VTEMP is in mV.
GAIN1: VTEMP = 907.9 - 5.132 ´ (TDIE - 30°C) - 1.08 -3 ´ (TDIE - 30°C)
GAIN2 : VTEMP = 1361.4 - 7.701´ (TDIE - 30°C) - 1.6 -3 ´ (TDIE - 30°C)
GAIN3 : VTEMP = 1814.6 - 10.27 ´ (TDIE - 30°C) - 2.12 -3 ´ (TDIE - 30°C)
GAIN4 : VTEMP = 2268.1 - 12.838 ´ (TDIE - 30°C) - 2.64 -3 ´ (TDIE - 30°C)
(1)
7.3.2.2 The First-Order Approximation (Linear)
For a quicker approximation, although less accurate than the second-order, over the full operating temperature
range the linear formula below can be used. Using Equation 2, with the constant and slope in the following set of
equations, the best-fit VTEMP versus die temperature performance can be calculated with an approximation error
less than 18 mV. VTEMP is in mV.
GAIN1: VTEMP = 1060 - 5.18 ´ TDIE
GAIN2 : VTEMP = 1590 - 7.77 ´ TDIE
GAIN3 : VTEMP = 2119 - 10.36 ´ TDIE
GAIN4 : VTEMP = 2649 - 12.94 ´ TDIE
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
(2)
Submit Documentation Feedback
17
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
7.3.2.3 First-Order Approximation (Linear) Over Small Temperature Range
For a linear approximation, a line can easily be calculated over the desired temperature range from Table 1 using
the two-point equation:
æ V - V1 ö
V - V1 = ç 2
÷ ´ (T - T1 )
è T2 - T1 ø
where
•
•
•
•
V is in mV
T is in °C
T1 and V1 are the coordinates of the lowest temperature
T2 and V2 are the coordinates of the highest temperature
(3)
For example, to determine the equation of a line with GAIN4, with a temperature from 20°C to 50°C, proceed
using Equation 4, Equation 5, and Equation 6:
æ 2010 mV - 2396 mV ö
V - 2396 mV = ç
÷ ´ (T - 20°C)
50°C - 20°C
è
ø
(4)
V – 2396 mV = –12.8 mV/°C × (T – 20°C)
V = –12.8 mV/°C × (T – 20°C) + 2396 mV
(5)
(6)
Using this method of linear approximation, the transfer function can be approximated for one or more
temperature ranges of interest.
7.3.3 OVERTEMP and OVERTEMP Digital Outputs
The OVERTEMP active high, push-pull output and the OVERTEMP active low, open-drain output both assert at
the same time whenever the die temperature reaches the factory preset temperature trip point. They also assert
simultaneously whenever the TRIP_TEST pin is set high. Both outputs deassert when the die temperature goes
below the temperature trip point hysteresis. These two types of digital outputs enable the user the flexibility to
choose the type of output that is most suitable for his design.
Either the OVERTEMP or the OVERTEMP digital output pins can be left open if not used.
7.3.3.1 OVERTEMP Open-Drain Digital Output
The OVERTEMP active low, open-drain digital output, if used, requires a pullup resistor between this pin and
VDD. The following section shows how to determine the pullup resistor value.
7.3.3.1.1 Determining the Pullup Resistor Value
VDD
iT
RPull-Up
VOUT
OVERTEMP
Digital Input
iL
isink
18
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
The pullup resistor value is calculated at the condition of maximum total current, IT, through the resistor. The total
current is:
IT = IL + ISINK
where
•
•
IT is the maximum total current through the pullup resistor at VOL.
IL is the load current, which is very low for typical digital inputs.
(7)
The pullup resistor maximum value can be found by using Equation 8.
VDD(MAX) - VOL
R PULLUP =
IT
where
•
•
VDD(MAX) is the maximum power supply voltage to be used in the customer's system.
VOUT is the Voltage at the OVERTEMP pin. Use VOL for calculating the pullup resistor.
(8)
7.3.3.1.1.1 Example Calculation
Suppose, for this example, a VDD of 3.3 V ± 0.3 V, a CMOS digital input as a load, a VOL of 0.2 V.
•
•
•
•
For VOL of 0.2 V the electrical specification for OVERTEMP shows a maximum ISINK of 385 µA.
Let IL = 1 µA, then IT is about 386 µA maximum. If 35 µA is selected as the current limit then IT for the
calculation becomes 35 µA.
VDD(MAX) is 3.3 V + 0.3 V = 3.6 V, then calculate the pullup resistor as RPULLUP = (3.6 – 0.2) / 35 µA = 97 kΩ.
Based on this calculated value, select the closest resistor value in the tolerance family used.
In this example, if 5% resistor values are used, then the next closest value is 100 kΩ.
7.3.4 TRIP_TEST Digital Input
The TRIP_TEST pin simply provides a means to test the OVERTEMP and OVERTEMP digital outputs
electronically by causing them to assert, at any operating temperature, as a result of forcing the TRIP_TEST pin
high.
When the TRIP_TEST pin is pulled high the VTEMP pin is at the VTRIP voltage.
If not used, the TRIP_TEST pin may either be left open or grounded.
7.3.5 VTEMP Analog Temperature Sensor Output
The VTEMP push-pull output provides the ability to sink and source significant current. This is beneficial when, for
example, driving dynamic loads like an input stage on an analog-to-digital converter (ADC). In these applications
the source current is required to quickly charge the input capacitor of the ADC. See Application and
Implementation for more discussion of this topic. The LM26LV and LM26LV-Q1 are ideal for applications which
require strong source or sink current.
7.3.5.1 Noise Considerations
The LM26LV's and LM26LV-Q1's supply-noise rejection (the ratio of the AC signal on VTEMP to the AC signal on
VDD) was measured during bench tests. The device's typical attenuation is shown in Typical Characteristics. A
load capacitor on the output can help to filter noise.
For operation in very noisy environments, some bypass capacitance must be present on the supply within
approximately 2 inches of the LM26LV or LM26LV-Q1.
7.3.5.2 Capacitive Loads
The VTEMP Output handles capacitive loading well. In an extremely noisy environment, or when driving a switched
sampling input on an ADC, it may be necessary to add some filtering to minimize noise coupling. Without any
precautions, the VTEMP can drive a capacitive load less than or equal to 1100 pF as shown in Figure 20. For
capacitive loads greater than 1100 pF, a series resistor is required on the output, as shown in Figure 21, to
maintain stable conditions.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
19
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
VDD
LM26LV
OPTIONAL
BYPASS
CAPACITANCE
VTEMP
GND
CLOAD d 1100 pF
Figure 20. LM26LV or LM26LV-Q1 No Decoupling Required for Capacitive Loads Less Than 1100 pF.
VDD
LM26LV
OPTIONAL
BYPASS
CAPACITANCE
GND
VTEMP
RS
CLOAD >
1100 pF
Figure 21. LM26LV or LM26LV-Q1 With Series Resistor for Capacitive Loading Greater Than 1100 pF
Table 2. Minimum Series Resistence for Capacitive
Loads
CLOAD
MINIMUM RS
1.1 nF to 99 nF
3 kΩ
100 nF to 999 nF
1.5 kΩ
1 µF
800 Ω
7.3.5.3 Voltage Shift
The LM26LV and LM26LV-Q1 are very linear over temperature and supply voltage range. Due to the intrinsic
behavior of an NMOS/PMOS rail-to-rail buffer, a slight shift in the output can occur when the supply voltage is
ramped over the operating range of the device. The location of the shift is determined by the relative levels of
VDD and VTEMP. The shift typically occurs when VDD – VTEMP = 1 V.
This slight shift (a few millivolts) takes place over a wide change (approximately 200 mV) in VDD or VTEMP.
Because the shift takes place over a wide temperature change of 5°C to 20°C, VTEMP is always monotonic. The
accuracy specifications Accuracy Characteristics already includes this possible shift.
20
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
7.4 Device Functional Modes
The LM26LV and LM26LV-Q1 have several modes of operation as detailed in the following drawings.
VDD
VDD
4
NC
1
4
5
OVERTEMP
1
NC
LM26LV
6
3
100k
Asserts when TDIE > TTRIP
NC
LM26LV
See text.
3
OVERTEMP
6
Asserts when TDIE > TTRIP
NC
See text.
5
NC
2
NC
2
GND
GND
Copyright © 2016, Texas Instruments Incorporated
Copyright © 2016, Texas Instruments Incorporated
Figure 22. Temperature Switch Using Push-Pull
Output
Figure 23. Temperature Switch Using Open-Drain
Output
VDD
100k
4
TRIP TEST
3
1
LM26LV
6
5
OVERTEMP
NC
OVERTEMP
2
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 24. TRIP_TEST Digital Output Test Circuit
The TRIP_TEST pin, normally used to check the operation of the OVERTEMP and OVERTEMP pins, may be
used to latch the outputs whenever the temperature exceeds the programmed limit and causes the digital outputs
to assert. As shown in Figure 25, when OVERTEMP goes high the TRIP_TEST input is also pulled high and
causes OVERTEMP output to latch high and the OVERTEMP output to latch low. The latch can be released by
either momentarily pulling the TRIP_TEST pin low (GND), or by toggling the power supply to the device. The
resistor limits the current out of the OVERTEMP output pin.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
21
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Device Functional Modes (continued)
VDD
100k
4
TRIP TEST 1
RESET
Momentary
5
LM26LV
6
OVERTEMP
NC
3 OVERTEMP
2
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 25. Latch Circuit Using OVERTEMP Output
Alternately, the circuit in Figure 25 the 100 kΩ can be replaced with a short and the momentary reset switch may
be removed. In this configuration, when OVERTEMP goes active high, it drives TRIP_TEST high. THRIP TEST
high causes OVERTEMP to stay high. It is therefore latched. To release the latch, power down, then power up
the LM26LV or LM26LV-Q1. The LM26LV and LM26LV-Q1 always come up in a released condition.
22
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 ADC Input Considerations
The LM26LV and LM26LV-Q1 have an analog temperature sensor output VTEMP that can be directly connected to
an ADC (Analog-to-Digital Converter) input. Most CMOS ADCs found in microcontrollers and ASICs have a
sampled data comparator input structure. When the ADC charges the sampling cap, it requires instantaneous
charge from the output of the analog source such as the LM26LV or LM26LV-Q1 temperature sensor. This
requirement is easily accommodated by the addition of a capacitor (CFILTER). The size of CFILTER depends on the
size of the sampling capacitor and the sampling frequency. Because not all ADCs have identical input stages, the
charge requirements vary. This general ADC application is shown as an example only.
SAR Analog-to-Digital Converter
Reset
+1.6V to +5.5V
LM26LV
6
4
VDD
Input
Pin
RIN
CBP
1
2
Sample
VTEMP
TRIP
TEST
OT
GND
OT
5
CFILTER
CPIN
CSAMPLE
3
Copyright © 2016, Texas Instruments Incorporated
Figure 26. Suggested Connection to a Sampling Analog-to-Digital Converter Input Stage
8.2 Typical Application
VDD Supply
(+1.6V to +5.5V)
Example: 2 to 3
Battery Cells
VDD
VTEMP
LM26LV
Analog
ADC Input
Microcontroller
OVERTEMP
OVERTEMP
TRIP TEST
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 27. Typical Application Schematic
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
23
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
Typical Application (continued)
8.2.1 Design Requirements
For this design example, use the parameters listed in Table 3 as the input parameters.
Table 3. Design Parameters
PARAMETER
EXAMPLE VALUE
Temperature
0°C to 150°C (LM26LV), –40°C to 85°C for microcontroller
Accuracy
±2.3°C (Gain1, TA = 0°C to 150°C)
VDD
3.3 V
IDD
8 µA
8.2.2 Detailed Design Procedure
The LM26LV and LM26LV-Q1 come with a factory preset trip point. See Mechanical, Packaging, and Orderable
Information for available trip point options. Figure 27 shows the device's OVERTEMP output driving a
microcontroller interrupt input to indicate an overtemperature event. In addition to the OVERTEMP output, a
OVERTEMP output is available for use depending on the interrupt polarity of the microcontroller's interrupt pin. A
VTEMP analog output is available to drive the microcontroller ADC input allowing the microcontroller to
determine the sensing temperature of the LM26LV or LM26LV-Q1. The TRIP_TEST input is connected to a
microcontroller output pin allowing the microcontroller to run on the fly electrical conductivity testing. For normal
operation TRIP_TEST must be driven low by the microcontroller output. If no testing is required, the TRIP_TEST
pin may be continuously grounded.
8.2.3 Application Curves
VTEMP Output
(Temp. of Leads)
Trip Point
Trip Point - Hysteresis
OVERTEMP
OVERTEMP
Figure 28. VTEMP Analog Output Temperature Error
24
Submit Documentation Feedback
Figure 29. Switch Output Function
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
9 Power Supply Recommendations
Bypass capacitors are optional, and maybe required if the supply line is extremely noisy at high frequencies. TI
recommends that a local supply decoupling capacitor be used to reduce noise. For noisy environments, TI
recommends a 100-nF supply decoupling capacitor placed closed across the VDD and GND pins of the LM26LV
or LM26LV-Q1.
9.1 Power Supply Noise Immunity
The LM26LV and LM26LV-Q1 are virtually immune from false triggers on the OVERTEMP and OVERTEMP
digital outputs due to noise on the power supply. Test have been conducted showing that, with the die
temperature within 0.5°C of the temperature trip point, and the severe test of a 3 V***pp square wave "***noise"
signal injected on the VDD line, with VDD from 2 V to 5 V, there were no false triggers.
10 Layout
10.1 Layout Guidelines
10.1.1 Mounting and Temperature Conductivity
The LM26LV or LM26LV-Q1 can be applied easily in the same way as other integrated-circuit temperature
sensors. The devices can be glued or cemented to a surface.
The best thermal conductivity between the device and the PCB is achieved by soldering the DAP of the package
to the thermal pad on the PCB. The temperatures of the lands and traces to the other leads of the LM26LV and
LM26LV-Q1 also affect the temperature reading.
Alternatively, the LM26LV or LM26LV-Q1 can be mounted inside a sealed-end metal tube, and can then be
dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM26LV or LM26LV-Q1 and
accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is
especially true if the circuit may operate at cold temperatures where condensation can occur. If moisture creates
a short circuit from the VTEMP output to ground or VDD, the VTEMP output from the LM26LV or LM26LV-Q1 is not
correct. Printed-circuit coatings are often used to ensure that moisture cannot corrode the leads or circuit traces.
The thermal resistance junction-to-ambient (RθJA) is the parameter used to calculate the rise of a device junction
temperature due to its power dissipation. The equation used to calculate the rise in the LM26LV's and LM26LVQ1's die temperature is
TJ = TA + R qJA ´ ((VDD ´ IQ ) + (VDD - VTEMP ) ´ IL )
where
•
•
•
•
TA is the ambient temperature
IQ is the quiescent current
IL is the load current on the output
VO is the output voltage
(9)
For example, in an application where TA = 30°C, VDD = 5 V, IDD = 9 µA, Gain 4, VTEMP = 2231 mV, and IL = 2 µA,
the junction temperature would be 30.021°C, showing a self-heating error of only 0.021°C. Because the
LM26LV's and LM26LV-Q1's junction temperature is the actual temperature being measured, minimize the load
current that the VTEMP output is required to drive. If OVERTEMP is used with a 100‑k pullup resistor, and is
asserted (low), then for this example the additional contribution is (152°C/W) × (5 V)2 / 100 kΩ = 0.038°C for a
total self-heating error of 0.059°C. Thermal Information shows the thermal resistance of the LM26LV and
LM26LV-Q1.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
25
LM26LV, LM26LV-Q1
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
www.ti.com
10.2 Layout Example
VIA to power plane
Optional thermal VIA to ground plane
and back side of board for thermal
conductivity path
VIA to ground plane
R is optional maybe directly
connected to GND if TRIP TEST not used
TRIP TEST
VTEMP
GND
OVERTEMP
VDD
OVERTEMP
0.1 µ F
Figure 30. Typical Layout Example
VIA to power plane
Optional thermal VIA to ground plane
and back side of board for thermal
conductivity path
VIA to ground plane
TRIP TEST
GND
OVERTEMP
VTEMP
OVERTEMP
VDD
0.1 µ F
Figure 31. Latching Layout Example
26
Submit Documentation Feedback
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
LM26LV, LM26LV-Q1
www.ti.com
SNIS144G – JULY 2007 – REVISED SEPTEMBER 2016
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
Absolute Maximum Ratings for Soldering (SNOA549)
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM26LV
Click here
Click here
Click here
Click here
Click here
LM26LV-Q1
Click here
Click here
Click here
Click here
Click here
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2007–2016, Texas Instruments Incorporated
Product Folder Links: LM26LV LM26LV-Q1
Submit Documentation Feedback
27
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM26LVCISD-050/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
050
LM26LVCISD-060/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
060
LM26LVCISD-065/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
065
LM26LVCISD-070/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
070
LM26LVCISD-075/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
075
LM26LVCISD-080/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
080
LM26LVCISD-085/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
085
LM26LVCISD-090/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
090
LM26LVCISD-095/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
095
LM26LVCISD-100/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
100
LM26LVCISD-105/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
105
LM26LVCISD-110/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
110
LM26LVCISD-115/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
115
LM26LVCISD-120/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
120
LM26LVCISD-125/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
125
LM26LVCISD-135/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
135
LM26LVCISD-140/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
140
LM26LVCISD-145/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
145
LM26LVCISD-150/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
150
LM26LVCISDX-060/NOPB
ACTIVE
WSON
NGF
6
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
060
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Dec-2020
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM26LVCISDX-120/NOPB
ACTIVE
WSON
NGF
6
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
120
LM26LVQISD-130/NOPB
ACTIVE
WSON
NGF
6
1000
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
Q30
LM26LVQISDX-130/NOPB
ACTIVE
WSON
NGF
6
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
Q30
LM26LVQISDX-135/NOPB
ACTIVE
WSON
NGF
6
4500
RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 150
Q35
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of