LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
LM27213 Single Phase Hysteretic Buck Controller
Check for Samples: LM27213
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
•
•
The LM27213 is a single-phase synchronous buck
regulator controller designed to fully support a
portable microprocessor. On-chip gate drive makes
for a compact, single chip solution. Output currents in
excess of 25 Amps are possible.
1
2
Ideal Load and Line Transient Responses
5V to 30V Input Range
On-Chip Gate Drive
Convenient CLK_EN# Signal
Input Under-Voltage Lockout
High Light-Load Efficiency
Adjustable Analog Soft Start
Peak Current Limit
Over-Voltage Protection
Error Correction for Good Static Accuracy
±1% DAC Accuracy Over Temperature
Interfaces with the LM2647 System Supply
Available in TSSOP or WQFN Packages
APPLICATIONS
•
•
•
•
•
Core Voltage Supply for Low Power
Processors
Low Voltage High Current Buck Regulators
Benefits
Single Chip Core Power Solution
Minimum Output Capacitance Required
Low Cost, Compact Design
The IC employs a current mode hysteretic control
mechanism. Inductor current is sensed through a low
value sense resistor.
The LM27213 will operate over an input voltage
range of 5V to 30V. The output voltage is
programmed through 6 Voltage Identification (VID)
pins and ranges from 0.700V to 1.708V in 64 steps.
Since the error in the output voltage directly sets the
inductor current, the dynamic response to a large,
fast load transient is close to a square wave. This is
optimal for mode transition requirements. Also, due to
the intrinsic input voltage feedforward characteristic of
hysteretic control, the line transient response is
excellent as well.
The IC provides cycle-by-cycle peak current limit,
over-voltage protection, and a power good signal.
The LM27213 fully supports the Stop CPU and Sleep
modes offered by some processors. When enabled,
the IC enters a power-saving “diode emulator” mode
which helps prolong battery runtime for portable
systems.
The LM27213 also has a soft start feature for the
external adjustment of soft start speed.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Application
VCC5
VDC
U1
DVDD
VDD
CBOOT
V1R7
VOVP
VBOOT
HG
SW
VSLP
SS
VCORE
LG
LM27213
DE_EN#
VID0
VID1
VID2
VID3
VID4
VID5
CLK_EN#
STP_CPU#
XPOK
STP
SLP
PGOOD
VDAC
VSTP
SGND
SRCK
+
PGND
DGND
ILIMREF
ILIM
SENS
CM
VREF
CMPREF
PVDD
LG
NC
PGND
NC
NC
VRON
VID0
VID1
VID2
VID3
VID4
VID5
DE_EN#
STP_CPU#
SLP
VSTP
VDAC
NC
NC
VSLP
VBOOT
V1R7
SS
36
35
34
33
32
31
30
29
28
27
26
25
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
VID4
VID3
VID2
VID1
VID0
VRON
NC
NC
PGND
NC
LG
PVDD
Figure 1. Top View
48-Lead TSSOP
See DGG Package
2
37
38
39
40
41
42
43
44
45
46
47
48
24
23
22
21
20
19
18
17
16
15
14
13
VDD
SGND
P_Z0
NC
NC
P_Z1
P_Z2
VOVP
SENSE
XPOK
PGOOD
DGND
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CBOOT
HG
SW
NC
SRCK
NC
ILIM
ILIMREF
CMP
CMPREF
VREF
CLK_EN#
CBOOT
HG
SW
NC
SRCK
NC
ILIM
ILIMREF
CMP
CMPREF
VREF
CLK_EN#
DGND
PGOOD
XPOK
SENSE
VOVP
P_Z2
P_Z1
NC
NC
P_Z0
SGND
VDD
VID5
DE_EN#
STP_CPU#
SLP
VSTP
VDAC
NC
NC
VSLP
VBOOT
V1R7
SS
Connection Diagram
Figure 2. Top View
48-Lead WQFN
See RHS0048A Package
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
PIN DESCRIPTIONS (TSSOP/LLP)
Pin
Name
Description
1
CBOOT
2
HG
High-side FET gate drive output
3
SW
Connect to switch node (drain of bottom power FET) to detect inductor current reversal. Also
serves as the return path for the high-side FET gate drive currents
4
NC
No connect
5
SRCK
6
NC
No connect
7
ILIM
Over-current sense. Voltage between this pin and the regulator output is the voltage across
the current sense resistor
8
ILIMREF
Current limit reference. Voltage between this pin and the regulator output sets the inductor
current limit level
9
CMP
10
CMPREF
11
VREF
12
CLK_EN#
13
DGND
14
PGOOD
15
XPOK
16
SENSE
17
VOVP
Over-voltage protection level. Connect this pin to the desired reference voltage to set the
trigger level for over-voltage protection
18
P_Z2
Factory reference trim, do not connect. This pin must float
19
P_Z1
Factory reference trim, do not connect. This pin must float
20
NC
No connect
21
NC
No connect
22
P_Z0
Factory reference trim, do not connect. This pin must float
23
SGND
Signal Ground
24
VDD
25
SS
26
VIR7
27
VBOOT
28
VSLP
29
NC
No connect
30
NC
No connect
31
VDAC
Buffered Digital-to-Analog converter output
32
VSTP
Desired output voltage in Stop CPU mode. Connect this pin to the desired reference level
33
SLP
When this pin is logic high, VREF voltage is equal to that on the VSLP pin
34
STP_CPU#
When this pin is logic low, VREF voltage is equal to that on the VSTP pin
35
DE_EN#
36
VID5
6th and most significant bit to program the output voltage
37
VID4
5th bit to program the output voltage
38
VID3
4th bit to program the output voltage
39
VID2
3rd bit to program the output voltage
Connection for the high-side drive bootstrap capacitor
Source Kelvin. Connect directly to source of low-side FET to detect negative inductor current
Current sense. Voltage between this pin and the regulator output sets the cycle by cycle
inductor current
Inductor current reference. Voltage between this pin and the regulator output programs the
inductor current
Desired regulator output voltage under no load
Signal to start clock chip PLL locking. A low level indicates that the core supply is now stable
and the CPU can begin clocking
Digital ground
Power good flag. Open-drain output. Logic high when output voltage enters the power good
window and XPOK is asserted. Masked during transitions
Input that tells the LM27213 that the supply voltage for the Memory Controller Hub is up. The
LM27213 will regulate the output voltage to VBOOT until XPOK transitions to a high state.
PGOOD is forced low as long as this pin is low
Regulator output voltage sense. Connect directly to output
Chip power supply
Soft start, soft shutdown and slew rate control. Connect a capacitor between this pin and
ground to control the soft start and soft shutdown speed. The value of the capacitor will also
define the slew rate of the dynamic VID transitions
1.7V reference voltage
Initial output voltage desired after soft start completes. Connect this pin to the desired
reference level
Desired Voltage in Sleep Mode. Connect this pin to the desired reference level
Power saving mode trigger signal. Enables diode emulation
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
3
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
PIN DESCRIPTIONS (TSSOP/LLP) (continued)
Pin
Name
Description
40
VID1
2nd bit to program the output voltage
41
VID0
First and least significant bit to program the output voltage
42
VR_ON
43
NC
No connect
44
NC
No connect
45
PGND
46
NC
Power ground connection
47
LG
Low-side FET gate drive output
48
PVDD
Power input for the gate drives
Chip enable input
Power Ground. Connect to ground plane
VID
4
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
Voltage
(V)
VID
Voltage
(V)
5
4
3
2
1
0
1.708
1
0
0
0
0
0
1.196
1.692
1
0
0
0
0
1
1.180
0
1.676
1
0
0
0
1
0
1.164
1
1
1.660
1
0
0
0
1
1
1.148
0
0
1.644
1
0
0
1
0
0
1.132
1
0
1
1.628
1
0
0
1
0
1
1.116
0
1
1
0
1.612
1
0
0
1
1
0
1.100
0
1
1
1
1.596
1
0
0
1
1
1
1.084
0
1
0
0
0
1.580
1
0
1
0
0
0
1.068
0
0
1
0
0
1
1.564
1
0
1
0
0
1
1.052
0
0
1
0
1
0
1.548
1
0
1
0
1
0
1.036
0
0
1
0
1
1
1.532
1
0
1
0
1
1
1.020
0
0
1
1
0
0
1.516
1
0
1
1
0
0
1.004
0
0
1
1
0
1
1.500
1
0
1
1
0
1
0.988
0
0
1
1
1
0
1.484
1
0
1
1
1
0
0.972
0
0
1
1
1
1
1.468
1
0
1
1
1
1
0.956
0
1
0
0
0
0
1.452
1
1
0
0
0
0
0.940
0
1
0
0
0
1
1.436
1
1
0
0
0
1
0.924
0
1
0
0
1
0
1.420
1
1
0
0
1
0
0.908
0
1
0
0
1
1
1.404
1
1
0
0
1
1
0.892
0
1
0
1
0
0
1.388
1
1
0
1
0
0
0.876
0
1
0
1
0
1
1.372
1
1
0
1
0
1
0.860
0
1
0
1
1
0
1.356
1
1
0
1
1
0
0.844
0
1
0
1
1
1
1.340
1
1
0
1
1
1
0.828
0
1
1
0
0
0
1.324
1
1
1
0
0
0
0.812
0
1
1
0
0
1
1.308
1
1
1
0
0
1
0.796
0
1
1
0
1
0
1.292
1
1
1
0
1
0
0.780
0
1
1
0
1
1
1.276
1
1
1
0
1
1
0.764
0
1
1
1
0
0
1.260
1
1
1
1
0
0
0.748
0
1
1
1
0
1
1.244
1
1
1
1
0
1
0.732
0
1
1
1
1
0
1.228
1
1
1
1
1
0
0.716
0
1
1
1
1
1
1.212
1
1
1
1
1
1
0.700
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1) (2)
VDD, DVDD XPOK, VR_ON, DE_EN#, VOVP, VBOOT, VID0 to VID5,
STP_CPU#, SLP, VSLP, VSTP, SENSE, CMP1, CMP2, CMPREF,
ILIM1, ILIM2, ILIMREF
-0.3V to 7V
PGOOD
-0.3V to 6V
(3)
-2V to 30V
CBOOT to SW
-0.3V to 8V
SW to GND
Power Dissipation
TSSOP, TA = 25°C,
(4)
1.56W
(4)
4.9W
Junction Temperature
+150°C
WQFN, TA = 25°C,
Functional Temp. Range
ESD Rating
-20°C to +110°C
(5)
2kV
Storage Temp Range
-65°C to +150°C
Soldering Dwell Time, Temperature
Wave
Infrared
Vapor Phase
(1)
(2)
(3)
(4)
(5)
4sec, 260°C
10sec, 240°C
75sec, 219°C
Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is ensured. For ensured performance limits and associated test conditions, see the Electrical Characteristics
table. Functional temperature range is the range within which the device performs its intended functions, but not necessarily meeting the
limits specified in the Electrical Characteristic table.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
The SW pin can have -2V to -0.5 volts applied for a maximum duty cycle of 10% with a minimum frequency of 1Hz. There is no duty
cycle or maximum period limitation for a SW pin voltage range of -0.5V to 30 Volts.
The maximum allowable power dissipation is calculated by using PDmax = (TJMAX - TA) /θJA , where TJMAX is the maximum junction
temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance of the specified package. The TSSOP
rating of 1.56W results from using 150°C, 25°C, and 80°C/W for TJMAX, TA, and θJA respectively. The θJA of 90°C/W represents the
worst-case condition with no heat sinking of the 48-Pin TSSOP. Heat sinking allows the safe dissipation of more power. The Absolute
Maximum power dissipation should be de-rated by 12.5mW per °C above 25°C ambient. The SQA rating of 5.2W results from using
150°C, 25°C, and 24.2°C/W for TJMAX, TA, and θJA respectively. The Absolute Maximum power dissipation should be de-rated by 41mW
per °C above 25°C ambient. The LM27213 actively limits its junction temperature to about 150°C.
For testing purposes, ESD was applied using the human-body model, a 100pF capacitor discharged through a 1.5kΩ resistor.
Operating Ratings
(1)
VDD
4.75V to 6V
Junction Temperature
-5°C to +110°C
Ambient Temperature
-5°C to +105°C
(1)
Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is ensured. For ensured performance limits and associated test conditions, see the Electrical Characteristics
table. Functional temperature range is the range within which the device performs its intended functions, but not necessarily meeting the
limits specified in the Electrical Characteristic table.
Electrical Characteristics
Specifications with standard typeface are for TJ = 25°C, and those in bold face type apply over a junction temperature range
of -5°C to +110°C. Unless otherwise specified, VDD = 5V, SGND = DGND = PGND = SRCK = 0V, unless otherwise stated.
(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Chip Supply
(1)
Isd
VDD Shutdown Current
VR_ON = 0V, VDD = 6V
1
10
µA
Iq
VDD Normal Operating Current
VR_ON = 3.3V
3
4.2
mA
All limits are specified at room temperature (standard face type) and at temperature extremes (bold face type). All room temperature
limits are 100% production tested. All limits at temperature extremes are ensured via correlation using Statistical Quality Control (SQC)
methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
5
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Electrical Characteristics (continued)
Specifications with standard typeface are for TJ = 25°C, and those in bold face type apply over a junction temperature range
of -5°C to +110°C. Unless otherwise specified, VDD = 5V, SGND = DGND = PGND = SRCK = 0V, unless otherwise stated.
(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
4
4.3
4.5
V
VDD = V5A = V5B falling from UVLO
Threshold
0.2
0.66
V
VR_ON, STP_CPU#, XPOK and SLP
Input Logic High
VR_ON, STP_CPU#, XPOK or SLP rising
from 0V
2.31
1.9
V
VR_ON, STP_CPU#, XPOK and SLP
Input Logic Low
VR_ON, STP_CPU#, XPOK or SLP
falling from 3.3V
CLK_EN# Sink Current
CLK_EN# = 0.1V and asserted
2.5
7
VPGH
Power Good Upper Threshold As A
Percentage of VREF
SENSE voltage rising from 0V
108
114
119
%
VPGL
Power Good Lower Threshold As A
Percentage of VREF
SENSE voltage falling from above VREF
85
88
91
%
UVLO Threshold
VDD = V5A = V5B, rising from 0V
UVLO Hysteresis
VLH
VLL
Logic
1.43
0.99
V
mA
Power Good
Hysteresis
5
%
tdpgood
Power Good Delay
3
µs
Ipgood
PGOOD Sink Current
mA
PGOOD = 0.1V and asserted
2.5
7
SS = 0V
Output Voltage Slew Rate Control
Iss(on)
Soft Start Current
16
22
32
µA
Iss(off)
Soft Shutdown Current
33
45
57
µA
VID and Mode Change Slew Rate Control
Current
255
337
415
µA
0.63
0.56
Iss(slew)
DAC and References
VIDLH
VID Pins Input Logic High
VIDLL
VID Pins Input Logic Low
Vdac
V1R7
IVREF
IVDAC
IV1R7
0.48
DAC Accuracy
V
0.315
Measured at VREF pin
V
%
DAC codes from 0.7V to 0.828V
-1.3
1.3
DAC codes from 0.844V to 1.004V
-1.1
1.1
DAC codes from 1.020V to 1.196V
-0.9
0.9
DAC codes from 1.212V to 1.356V
-1
1
DAC codes from 1.372V to 1.500V
-1.1
1.1
DAC codes from 1.516V to 1.708V
-1.3
17kΩ from V1R7 to GND
VSTP Offset
VSTP = 1.398V, Measured at VREF pin
VBOOT Offset
VBOOT = 1.00V, Measured at VREF pin
VSLP Offset
VSLP = 0.748V, Measured at VREF pin
VREF Driving Capability
source
1.3
mA
sink
12.6
mA
source
1.3
mA
sink
13.4
mA
µA
VDAC Driving Capability
V1R7 Driving Capability
-1.674
1.3
V1R7 Accuracy
1.708
1.742
V
-5
5
mV
-5
5
mV
-5
5
mV
source
90
549
Error Comparator Input Bias Current
(Sourcing)
CMP = 1.436V.
12
21
33
µA
VOSEC
Error Comparator Input Offset Voltage
CMPREF = 1.436V.
-3
3
mV
IHYST
Hysteresis Current (bi-directional)
Rhys = 17kW
38
50
68
µA
Error Comparator
IBEC
Rhys = 170kW
6
Submit Documentation Feedback
5
µA
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
Electrical Characteristics (continued)
Specifications with standard typeface are for TJ = 25°C, and those in bold face type apply over a junction temperature range
of -5°C to +110°C. Unless otherwise specified, VDD = 5V, SGND = DGND = PGND = SRCK = 0V, unless otherwise stated.
(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
9
21
35
µA
2
mV
395
µA
Current Limit
IBCLC
VOSCLC
Current Limit Comparator Input Bias
Current
Current Limit Comparator Input Offset
Voltage
ILIMREF = 1.436V.
Current Limit Setting Current
Rhys = 17kW, ILIMREF < ILIMx
-2
280
337
Rhys = 17kW, ILIMREF > ILIMx
250
µA
Rhys = 170kW, ILIMREF < ILIMx
30
µA
Time Delays
tBOOT
tCPU_PWRGD
tMASK
tdPG
VBOOT Voltage Holdup Time
From assertion of XPOK to assertion of
CLK_EN#.
10
17
30
µs
Power Good Mask For Initial VID Voltage
Settling
From assertion of CLK_EN# to assertion
of PGOOD.
3
5
9
ms
100
129
179
µs
Power Good Mask For VID Changes
Power Good De-assertion Delay Upon
Shutdown
Delay From VR_ON de-assertion to
PGOOD de-assertion
60
ns
Over-voltage Protection
VTRIP
SENSE Voltage As A Percentage of
VOVP
VOVP = V1R7
109
125
0.63
0.56
139
%
System
DE_EN#LH
DE_EN# Input Logic High
DE_EN#LL
DE_EN# Input Logic Low
IDE_EN#
VSDT
V
0.47
0.315
V
6
100
µA
DE_EN# Pin Leakage Current
DE_EN# = 7.5V
Soft Shutdown Finish Threshold
Low-side driver enabled after shutdown
0.3
Driver Quiescent current
High drive = low, Low drive = high
VCBOOT = VDVDD = 5V
14
Top Driver pull-up current
VDVdd = 5V, Load = 0.1Ω
3
A
Top Drive pull-up Rds_on
ICBOOT = IHG = 0.7A
1.2
Ω
Top Drive pull-down current
VDVdd = 5V, Load = 0.1Ω
-3.2
A
V
Drivers
Iqdriver
100
µA
Top Drive pull-down Rds_on
Isw = IHG = 0.7A
0.6
Ω
TRISEHG
Top drive rise time
Cload = 3.3nF, (10% to 90%)
17
ns
tFALLHG
Top drive fall time
Cload = 3.3nF, (10% to 90%)
12
ns
Bottom driver pull-up current
VDVdd = 5V, Load = 0.1Ω
3.2
A
Bottom Drive pull-up Rds_on
ICBOOT = IlG = 0.7A
2.9
Ω
Bottom Drive pull-down currrent
VDVdd = 5V, Load = 0.1Ω
3.2
A
Bottom Drive pull-down Rds_on
Isw = IlG = 0.7A
0.6
Ω
TRISELG
Bottom Drive rise time
Cload = 3.3nF, (10% to 90%)
17
ns
TFALLLG
Bottom Drive fall time
Cload = 3.3nF, (10% to 90%)
14
ns
Prop delay, CMP to top driver
CMP rising above CMPREF (20mV
overdrive) to HG dropping to VSW + 0.9
VDVdd, Cload = 3.3nF
89
ns
TDLY
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
7
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Application
VCC5
R2
2.2
R1
10
C1
1.0 PF
D1
CMDSH-3
C2
1.0 PF
C3
0.22 PF
VDC
C8
4.7 PF
x4
U1
DVDD
VDD
R3
0
HG
VID0
VID1
VID2
VID3
VID4
VID5
CLK_EN#
VR_ON
XPOK
STP_CPU#
SLP
PGOOD
R5
4.53k
R6
7.50k
R7
1.21k
SS
R8
100k
C5
0.022 PF
VCORE
Q1
Si7336
x2
LG
LM27213
DE_EN#
VID0
VID1
VID2
VID3
VID4
VID5
CLK_EN#
STP_CPU#
XPOK
STP
SLP
PGOOD
VDAC
VSTP
SGND
L1
0.56 PH
SW
VSLP
DE_EN#
R4
5.11k
Q1
Si7392
CBOOT
V1R7
VOVP
VBOOT
SRCK
R11
.003
PGND
C9
22 PF
x 22
+
C10
330 PF
x2
DGND
R9 182
ILIMREF
C4
1200 pF
ILIM
SENS
CM
VREF
CMPREF
R10 100
C6
0.1 PF
C7
1200 pF
C8, TDK C3216X5R1E475K
C9, AVX 12066D226MAT
C10, Panasonic EEFSD0D330R
L1, Panasonic ETQP4LR56WFC
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
Block Diagram
1.255V
POR
VDD
1.255V
STP_ CPU#
Mode
Logic
async.
P_Z2
Logic
SRCK
BG
soft_ start
Cboot
P_Z1
mode
HG
+
-
VDAC
zero cross detect
Bias
SLP
VID0
DE_EN#
vid_ change
1. 255V
+
-
uvlo
+
-
1. 708V
+
por
P_Z0
Anti shoot
thru logic
1. 708V
SW
current_ lim #
DVDD
VID1
VID2
LG
+
6-Bit
DAC
PGND
VID3
5V
VREF
VID4
ILIM
VID5
0. 5 x ih
enable #
current_ lim
+
-
mode
VSTP
ILIMREF
ih
3 x ih
VBOOT
5V
VSLP
CMP
+
-
+
-
+
CMPREF
VID0-5
SS
0.2V
5V
+
mode
XOR
Edge
Circuit
100 Ps
Delay
PGOOD
5V
DGND
ih
SENSE
soft_off
S>R
R Q
20 Ps
Delay
enable
por
1.708V
+
soft_off
V1R7
VOVP
+
-
0.88
+
-
0.80
OV
+
S Q
VRON
SGND
enable#
6 ms
Delay
Q R
ovp
CLK _EN#
por
soft_off
20Ps
Delay
20 PA
Q S
XPOK
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
9
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Turn-On Waveforms
Transient Response
Ch1: VOUT
Ch3: VRON, VIN = 13V, IOUT = 0
3.5A to 12A load step
Cursor lines are spec limits
Ch1: VOUT
Ch4: IOUT, 8A/div
Figure 3.
Turn-Off Waveforms
VID Change, VID 5 from 1 to 0
Ch1: VOUT
Ch 3: VRON
Ch 4: PGOOD
Ch1: VOUT
Ch 3: VID5
Ch 4: PGOOD
Figure 5.
Figure 6.
Start-Up, VBOOT to VID Transition
VID Change, VID 5 from 0 to 1
Ch1: VOUT
Ch2: VID5
Ch 3: PGOOD
Ch1: VOUT
Ch2: CLK_EN#
Ch 3: XPOK
Ch 4: PGOOD
Figure 7.
10
Figure 4.
Figure 8.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Light Load, Diode Emulator Mode
LM29213 Typical Efficiency
90
EFFICIENCY (%)
85
8V
80
12V
20V
75
70
65
10
Figure 9.
Figure 10.
ILIMREF Bias
vs
VIN at 25°C
Hysteresis Current
vs
VIN at 25°C
HYSTERESIS CURRENT (PA)
150
337
336
335
140
130
120
110
100
4.5
5
5.5
6
6.5
4.5
5
5.5
VIN (V)
ILIM
vs
Temperature
Hysteresis Current
vs
Temperature
334.8
140
HYSTERESIS CURRENT (PA)
150
334.4
334.2
334
333.8
333.6
40
6.5
VIN (V)
Figure 12.
335
-10
6
Figure 11.
334.6
ILIM (PA)
15
LOAD CURRENT (A)
338
ILIMREF (PA)
5
0
Ch1: Switch Node
Ch2: VID5
Ch 3: VOUT
90
140
130
120
110
100
90
80
70
-10
40
90
140
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
11
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
DAC 100100 (1.32V)
vs
Temperature
UVLO Rising Threshold
vs
Temperature
1.134
4.27
UVLO THRESHOLD (V)
DAC 100100 (V)
1.133
1.132
1.131
1.130
4.265
4.26
4.255
4.25
-10
40
90
140
-10
TEMPERATURE (°C)
Figure 16.
DAC 100100
vs
VIN
UVLO Falling Threshold
vs
Temperature
140
UVLO FAALING THRESHOLD (V)
3.62
1.1325
DAC 100100 (V)
90
Figure 15.
1.1326
1.1324
1.1323
1.1322
1.1321
4.5
5
5.5
6
6.5
3.61
3.6
3.59
3.58
-10
40
90
140
TEMPERATURE (oC)
VIN (V)
Figure 17.
12
40
TEMPERATURE (°C)
Figure 18.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
APPLICATIONS INFORMATION
The LM27213 is a single phase current-mode hysteretic controller intended for controlling a power supply for a
low voltage CPU core. It is capable of currents up to approximately 25A with conventional surface mount power
devices. Hysteretic control assures the fastest possible transient response and a nearly ideal voltage positioning
droop response.
THEORY OF OPERATION
The LM27213 controls the inductor ripple current on a cycle by cycle basis. Several reference voltages are
available depending on the mode of operation selected. There is an internal DAC that gets programmed via 6
VID (Voltage Identification) bits. In addition, there are several inputs that allow separate references to be
selected in various “sleep modes”. An internal MUX selects the reference to be used by the control loop. A
softstart function controls the rate at which the selected reference is allowed to ramp up at turn on. There is a
cycle by cycle current limit loop as well as over voltage protection.
CONTROL LOOP OPERATION
The main regulator loop is a current mode hysteretic design that maintains control over the buck inductor’s peakpeak ripple current. A small hysteresis current is forced to flow through resistor RH which is connected between
the CMP pin and the left side of the current sense resistor. When the high-side switch is on, this current flows
into the pin forcing CMP below CMPREF. As the inductor current increases, the voltage at CMP rises. The error
comparator turns off the high-side switch and turns on the low-side switch when the inductor current exceeds the
demand. When the high-side switch turns off the hysteresis current is reversed and current is sourced from the
CMP pin. The error comparator now allows the inductor current to decay until the new threshold is crossed.
Refer to Figure 19 below. The hysteresis current actually consists of four components. The main hysteresis
source is programmed by the current out of the V1R7 reference pin. The total divider resistance on this pin
controls the magnitude of this current which is mirrored and sent to the CMP pin. This source will only be active
when the high-side switch is on. In addition, there’s a small correction current that varies as a function of duty
factor. Its magnitude is approximately 74µA*DF, where DF is the duty factor. At typical operating duty factors, it
will be around 7µA and in the same direction as the main hysteresis current. This current will flow at all times.
The tail current from the current sense comparator also needs to be accounted for. This 16µA flows from the
CMP pin when PWM is high, and from the CMPREF pin when PWM is low. Its direction is opposite that of the
hysteresis current source and so subtracts from the total hysteresis current. The final contribution to the
hysteresis current is the 50uA that is sourced continuously and serves as the “off” hysteresis. It is recommended
that approximately 100µA be programmed through the V1R7 pin. At this level the “on” and “off” currents are
approximately symmetrical around zero.
5V
Current Mirror
1. 708V
50 PA
Ihyst
+
CMP
DF
74 PA * DF
Current Mirror
V1R7
Enable
Vdd
Req
+
-
PWM
16 PA
CMPREF
Vdd
CMP
Figure 19.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
13
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
The current through the V1R7 pin is simply 1.708V divided by Req. Therefore the effective divider resistance
should be approximately 17kΩ. The hysteresis current when the high-side switch is on (assuming a roughly 10%
duty factor) is 100µA +7µA -16µA - 50µA = 41µA. When the high-side switch is off Ihyst is only 7µA -50µA = 43µA. It is the difference between these two levels that controls the pk-pk inductor current or:
ΔIhyst = IV1R7 -16µA
(1)
Note that the correction current (74µA *DF) does not appear in this equation. It serves only to move the output
voltage slightly as a function of duty factor to correct for offsets that are inherent in the topology.
Figure 20 shows a higher level picture of the control loop. The reference that the CMP voltage is compared to is
the voltage at the CMPREF pin. Assume that the CMPREF pin is simply tied to a fixed reference voltage (R2
open). The control loop would force the peak voltage at point A minus the hysteresis voltage to equal the
reference level. Since the on and off hysteresis currents are symmetrical around zero, the average voltage at
point A is therefore equal to the reference voltage. There will be a voltage droop as a function of load (load line)
equal to the value of Rsense, the current sense resistor. Adding resistors R1 and R2 allows this load line slope
to be increased without raising the value of the sense resistor. The voltage across R2 will equal the voltage
across the sense resistor, Rs. So, if R1 = R2 the load line will be twice Rs. Algebraically,
LL = Rs x (1+R1/R2)
(2)
When the high-side switch has been turned off, the 16µA comparator input bias current now flows out of the
CMPREF pin through the parallel combination of R1 and R2. This results in a small increase in the reference
voltage (about 1mV with typical values) and will reduce the size of the hysteresis band by an equal amount.
Vin
A R sense
+
LM27213
RH
IH
+
CMP
CMPREF
Vref
R1
R2
Figure 20.
Figure 21 below shows the theoretical waveform that is to be expected at the CMP pin. Zero output ripple voltage
is assumed. In reality these signals ride on top of the regulator’s output ripple and may be very hard to discern.
There’s a small delay time from the instant the voltage on the CMP pin crosses the voltage on CMPREF. This
delay will result in the inductor peak current overshooting the hysteresis setting. For high step-down ratios the
inductor current down-slope will be much more shallow than the up-slope. Therefore, the undershoot magnitude
will be less than the overshoot magnitude. As a result of these delays the actual hysteresis will be somewhat
greater than programmed.
The actual wave shapes will be very dependant on the type of output capacitor selected. The resistive
component of electrolytic type capacitors (ESR) will serve to provide a significant amount of instantaneous
feedforward due to the current flow through the capacitors. By contrast, if an all ceramic output capacitor
decoupling network is employed, the current flow through the capacitor is integrated over time, and current
information is phase shifted. This tends to alter the regulator’s behavior somewhat. In particular, the operating
frequency will be very hard to predict since decoupling parasitics play a significant part in shaping the waveforms
at the CMP pin. As such, it is generally simplest to choose the final value for the hysteresis resistor empirically.
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
Vhyst =
RH*Ihyst(off)
CMPREF
Vhyst =
RH*Ihyst (on)
VCMP
Delay time
Figure 21.
The approximate operating frequency is:
FSW = RS x (VO -VIN)
VO
>'Ihys x Rhys x L x (2 x VO ± VIN)]
where
•
•
•
•
Rs is the value of the current sense resistor in Ohms
L is the inductor value in µH
ΔIhyst is the hysteresis current in Amps
Rhys is the value of the hysteresis resistor in Ohms
(3)
This equation is greatly simplified and fails to account for the effects of output ripple, comparator delay times etc.
There are far too many subtle variables involved in this topology to be able to make very accurate operating
frequency estimates. This equation should provide a ballpark starting point with the final value of the hysteresis
resistor arrived at empirically. At high frequency the delays through the comparator and driver will be the
dominant factor in determining the operating frequency.
CURRENT LIMITING
Current limit is achieved by comparing the instantaneous voltage across the current sense resistor with the
voltage developed across the current limit threshold resistor, R13 in the typical application circuit. If the controller
sees this threshold exceeded, the current switching cycle is terminated and the hysteresis current dropped in
half. The voltage across the current limit set point resistor is determined by the value of the resistor and the
magnitude of the current through the ILIMREF pin. This current is nominally three times the current drawn
through the V1R7 reference pin. When current limit is reached, this current is reduced to 250% of the V1R7
current. Be sure to use the full load DC current plus ½ the pk-pk inductor ripple current when determining the
required current sense threshold.
POWER GOOD
The output voltage is sensed at the Sense pin (16) and monitored by a window comparator with thresholds set to
nominally 88% and 112% of the selected output voltage set point. As long as Vcore remains within the window,
the power good signal will be logic high. This output is an open drain device and requires an external pull up. At
power up, the LM27213 will wait approximately 5ms after XPOK is asserted before releasing PGOOD. If the
output voltage is then within the ±12% window, the flag will be asserted.
OVER-VOLTAGE PROTECTION
The sense pin is also used to provide the input to the over-voltage protection circuitry. If at any time the output is
determined to be more than a nominal 120% of the voltage set on the VOVP pin (17), the high-side FET is
turned off and the low-side FET is turned on. The soft start capacitor will also be discharged. This state is
latched. In order to initiate a restart, remove and restore power to the controller or toggle the VRON pin.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
15
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
SOFT START
When VRON is enabled the regulator begins a normal start sequence that actively controls the rise of output
voltage. An internal 20µA current source supplies current through the Soft Start pin (25) that charges the soft
start capacitor. The output voltage is forced to track this voltage up. The result is a linear output voltage rise. The
capacitor value required is simply 20µA divided by the desired slew rate. For an output voltage rate of rise of
1V/ms, the capacitor should be about 20nF.
SOFT STOP
When VRON is deasserted, the LM27213 starts to discharge the soft start capacitor with an internal 45µA current
sink. Vcore is forced to follow the resulting linear ramp voltage on the soft start capacitor downward. When Vcore
reaches approximately 300mV the high-side FET is disabled and the low-side FET is turned on to quickly
discharge the output to zero and hold it there. This forces a controlled turn off slew rate that eliminates the
possibility of the output voltage ringing significantly below ground. It can also be helpful in the sequencing of
multiple supply rails.
STARTUP SEQUENCING
At initial power up the LM27213 targets a voltage equal to Vboot. This is the voltage level set at the VBOOT pin
(27) by a resistor divider that is powered by the V1R7 reference output (pin 26). This divider also has taps for the
OVP threshold and deeper sleep voltage set point. The regulator’s output will remain at Vboot until a time Tboot
after the XPOK flag clears. Tboot is nominally 20µs. After the Tboot time expires CLK_EN# will be asserted and the
output will transition to the voltage selected by the VID bits. Power good will be enabled nominally 5ms after
CLK_EN# is asserted.
DYNAMIC VID TRANSITIONS
Upon detecting a VID or mode change the LM27213 masks the power good comparator for a period of
approximately 130µs. During the blanking interval the power good output is forced high while the output voltage
is in slew to the newly selected level. The slew rate is determined by the soft start capacitor value. The
charge/discharge current driving the soft start capacitor will be 350µA typically. The programmed slew rate is
therefore 350µA divided by the soft start pin capacitance.
STOP CPU MODE
If the STP_CPU# pin (34) is asserted with SLP de-asserted the VREF pin voltage will be forced to the voltage on
the VSTP pin (32). The output will slew at a rate determined as above to the new value. The PGOOD mask is in
effect for 130µs.
SLEEP MODE
To enable sleep mode both STP_CPU# and SLP need to be asserted. The VREF pin voltage will transition to the
voltage on the VSLP pin with a slew rate as discussed under ynamic VID transitions and the PGOOD mask is
activated for 130µs.
POWER SAVING MODE
The LM27213 allows for high efficiency operation at very low power levels by employing a diode emulator mode.
This can be activated in either deep sleep or deeper sleep modes only. Assert the DE_EN# pin while in a sleep
mode to activate this function. When operating at low power the LM27213 detects inductor current reversal with a
zero cross detector connected to the drain of the low-side FET. The voltage at this node is normally below
ground when the low side FET is on but will become positive when the inductor current reverses. When the
inductor current reversal is detected the low side switch is turned off and essentially becomes a nearly ideal
diode. Due to the hysteretic control mode, the regulator operating frequency will be greatly reduced at light loads.
High-side switch on-time will not change significantly compared to normal operation, but the off times will extend
greatly. Care must be taken to connect the SRCK (Source Kelvin, pin 5) close to the low-side switch source
connection, as this is the reference input to the zero cross detector.
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
Component Selection
There are numerous tradeoffs to be made in settling on a final set of component choices and as a result the
process tends to be somewhat iterative. There’s always more than one combination of parts that will work in a
given application.
We will start with a few rule of thumb assumptions and then adjust as required to find a combination that meets
the specification requirements and is cost effective. Some of the choices can be thought of as somewhat
philosophical.
Let’s start the design by choosing an inductor and then develop the remainder of the design around that choice.
INDUCTOR SELECTION
A good place to start is by choosing an appropriate buck inductor. A decent rule of thumb is to allow the worst
case, peak to peak ripple current to be on the order of 40% to 50% of the full load output current. So, for a
design of 12A at full load, the ripple current should be in the range of 4.8A to 6A. Larger or smaller ripple
currents may well be acceptable but there are tradeoffs associated with these choices. As inductor value
increases, there is a corresponding need to increase the amount of output capacitance to handle load transients.
Conversely, as inductance is reduced, the RMS switch currents tend to rise and therefore efficiency suffers
slightly while dynamic performance is improved.
The worst case ripple current will occur at the combination of maximum input and output voltage. Let’s assume
an output voltage of 1.180V and a maximum input of 16V. This will assume operation on a wall adapter while
battery voltage may be only 12V maximum. Another assumption that must be made is the intended operating
frequency. Again there exists a tradeoff between dynamic performance and efficiency. The “sweet spot” at the
time of this writing is roughly in the range of 300kHz to 400kHz. That will in all likelihood shift positive in time as
FET technology improves. The hysteretic architecture also varies the operating frequency as a function of input
voltage with the regulator tending to run a bit slower at high input voltages. Let’s assume a 300kHz frequency at
high input line. Also, since the efficiency is of somewhat less of a concern when operating from a wall adapter
we’ll design for the high end of the ripple current range under this condition. The ripple current will be lower when
operating from a battery since the input voltage will be lower and the switching frequency will be somewhat
higher. With all that settled let’s calculate a value for L.
L = (VIN-VO)VO/(ΔI x VIN x fSW)
where
•
•
•
•
•
L is the inductor value
Vin is the input voltage
Vo is the output voltage
ΔI is the ripple current
fsw is the switching frequency
(4)
So,
L = (16V-1.18V)1.18V/(6A x 16V x 300kHz)
where
•
L = 0.60 µH
(5)
If the switching frequency is pushed up a bit the inductor value may be reduced accordingly. In general for a
12A, low voltage CPU, a value between 0.56 µH and 0.7 µH works out well. The inductor chosen should be
capable of handling the full load current continuously. It must not hard saturate under fault conditions. The
saturation specifications for most inductors indicate when the inductance has fallen off by a given percentage.
This percentage will vary by manufacturer and is not standardized. As such, it’s best to look at the published
curves of inductance vs. DC current. If the inductor maintains more than 1/3 of it’s specified no load inductance
under short circuit conditions, it will probably work just fine. There will also most likely be an RMS current rating
for the inductor as well. This relates to the heating to be expected at the rated DC current. In most processor
applications it’s safe to assume the average DC current for thermal analysis purposes will be approximately 80%
of the specified maximum load current. The inductor should be specified for at least this value of continuous
current.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
17
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
OUTPUT CAPACITOR SELECTION
Once an inductor value is chosen it’s time to look at the output capacitors. There are several possible basic
approaches to take with regards to output de-coupling. It’s possible to use ceramic capacitors exclusively. This
will require a rather large number of small case size capacitors. It is also possible to use primarily aluminumpolymer type devices for the bulk decoupling with a relatively small number of ceramic capacitors for high
frequency bypassing. The third approach is something that’s more a combination of the two approaches, using a
moderate number of ceramic capacitor and a couple of large bulk caps. The design criteria will be slightly
different with the various approaches.
The controlling factor in a CPU core voltage regulator is generally the load-off transient. When the processor load
drops dramatically, all the energy stored in the inductor will get transferred into the output capacitors. The energy
stored in an inductor is L x I2/2 while the energy stored in a capacitor is C x V2/2. So:
Cmin = L(Imax2 - Imin2)/(Vmax2-Vinit2)
where
•
•
•
•
•
•
Cmin is the minimum capacitance required to meet the specified voltage limits
L is the inductor value
Imax is the peak inductor current at the time the load step occurs
Imin is the load current after the transient has settled
Vmax is the maximum allowed output voltage at the low load condition
Vinit is the initial output voltage at the time of the load step
(6)
It’s recommended that the current used for Imax be equal to the full load output current plus ½ the estimated pkpk ripple current
From the example being examined earlier, if we assume a 12A full load, a 0.56µH inductor, an initial voltage of
1.144V, a minimum current of 3.5A and a maximum voltage of 1.197V, the minimum allowable output
capacitance is calculated as:
Since ripple current is approximately 6A,
Imax = 12A + 3A = 15A
Cmin = 0.56µH(15A2 - 3.5A2)/1.197V2-1.144V2) = 960µF
(7)
(8)
This calculation assumes perfect capacitors (ESR = 0) and is a reasonable assumption for an all ceramic
solution only. More capacitance will be required if aluminum-poly type capacitors are used due to their higher
ESR. However, that will generally not be a problem since they tend to have large capacitance values. If using 22
µF, 1206 case ceramic capacitors, this design would require approximately 44 capacitors distributed around the
processor. Only capacitors with either X5R or X7R dielectrics should be considered. Lower cost devices have
voltage and temperature coefficients that make them unusable in these applications. Using a small number of
physically large ceramic capacitors is not recommended since the lead inductance will be excessive. They tend
not to provide adequate high frequency bypassing.
A reasonable way to reduce the capacitor count is through the addition of several aluminum-poly type capacitors.
A typical example may be the Panasonic SP series. A 330µF, 2.5V device is available with an ESR of only 5mΩ.
Adding a pair of these will permit reducing the number of ceramic capacitors considerably.
A reasonable estimate of the soar voltage when the load is suddenly reduced when using primarily alminum-poly
type capacitors can be obtained from the following equation:
§
1 x m x T2
+ (I) ± m x T) x ESR
¨I0 x T 2
©
ª
«
¬
§
¨
©
ª1
V(T) = «
¬C
where
•
•
•
•
•
18
V(T) is the instantaneous capacitor voltage increase above the initial DC voltage at the instant the load is
reduced
C is output capacitance in µF
I0 is the inductor current at the instant the load is decreased
ESR is the output capacitor ESR
m is the inductor current down slope equal to Vout/L
Submit Documentation Feedback
(9)
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
The maxima occurs at :
I0 - m x ESR x C
Tmax =
m
(10)
Simply solve for Tmax and substitute into the equation for V(T) to calculate the maximum output voltage rise.
This equation accounts for the decrease in voltage across the ESR as the capacitors are being charged by the
decreasing inductor current.
Using numbers from the previous example:
Tmax = (12A-2.043A/µs*0.0025Ω*660µF)/2.043A/µs = 4.22µs
and
•
Vmax = 0.058V
(11)
This is just a bit higher than the specification allows but does not account for improvements expected as a result
of having a number of ceramic output capacitors on the board. The performance of combinations of capacitors is
best examined using a circuit simulator as the mathematics gets unwieldy. A simple model would be an inductor
connected in parallel with the output capacitors. Set the initial conditions for the peak inductor current at full load
and the capacitor voltage to the lowest point on the load line. A current source in parallel with the output that is
set for the minimum load current will allow the simulation of load steps that are less than 100% of full load.
A simulation of the above conditions with the addition of 10 pieces of a 22µF ceramic capacitor yields a peak
excursion of 1.180V, which is well within the specified limit.
MOSFET SELECTION
The choice of power FETs is driven primarily by efficiency or thermal considerations. There are two main loss
components to consider, conduction losses and switching losses. The switching losses are primarily due to
parasitics in the FETs and are very hard to estimate with any degree of accuracy. The conduction losses are
much easier to characterize. The switching losses in the synchronous FET are very low since it’s essentially a
zero voltage switched device. However, the high-side device’s switching losses are usually comparable to its
conduction losses. The primary contributor to high-side FET switching losses is related to the reverse recovery
characteristics of the synchronous FET’s body diode. During the small dead band where both FETs are off every
cycle, the synchronous FET’s body diode will carry the inductor current. Problems arise because the body diode
exhibits a significant reverse recovery time, trr. During this time, the FET looks like a short circuit. When the highside FET is subsequently turned on, there is a shoot through path from the input supply to ground. A larger highside FET will tend to exhibit a larger shoot through current. Therefore, it is undesirable to oversize the high-side
device. Since the synchronous FET looks like a short, the entire supply voltage is impressed across the high-side
device, along with a simultaneous high current. The result is very high momentary power dissipation. The total
power lost is a direct function of the switching frequency.
For a single-phase design something on the order of 1W of dissipation in the power switches is a reasonable
place to start. Assume further that this will be split equally between the high and low side FETs. Since the lowside FET switches at nearly zero volts the transition losses will be very low. The high-side switch will, however,
sustain large switching losses. In all likelihood they will be comparable to, or exceed, the conduction losses.
With 500mΩ allocated to the synchronous switch dissipation we can calculate the required on-resistance.
Assume the hot on-resistance will be about 140% of the room temp Rds(on). Therefore:
Rds(on) = Pdiss/(I2 x 1.4 x (1-DF))
where
•
•
•
DF = duty factor or Vout/Vin
Pdiss = allowed dissipation
I is the design thermal current
(12)
As a general rule of thumb, assume the design thermal current is approximately 80% of full load current unless
the specification indicates otherwise. In this case, assume a current of 9.6A. Also, duty factor should be
calculated at high input line voltage. Assume 16V for our example. So the maximum on-resistance for the
synchronous switch will be:
Rds(on) = 0.5W/(9.6A2 x 1.4 x (1-1.15V/16V))
• Rds(on) = 4.2mΩ
(13)
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
19
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
In a similar fashion the high-side switch can be sized. Allot ½ of the total dissipation to switching losses. The on
interval is now DF rather than 1-DF and low input line is assumed:
Rds(on) = Pdiss/(I2 x 1.4 x (DF))
Rds(on) = 0.25W/(9.6A2 x 1.4 x 1.15V/8V)
• Rds(on) = 13.4mΩ
(14)
(15)
An Si7390 high-side switch and an Si7336 low-side switch meet this requirement
If the same analysis is done assuming a 12A continuous load current the results suggest a low-side FET with an
on-resistance of 2.7mΩ and a high-side FET on-resistance of 8.6mΩ.
GATE DRIVE REQUIREMENTS
The bootstrap capacitor choice is based largely on the gate charge requirements of the high-side FET. The
charge stored on the bootstrap cap should be about 20X the high-side FET’s gate charge. For the Si7390 the
specified gate charge is 15nC max. So the bootstrap capacitor should store a minimum of 300nC at 5V. This
translates to a capacitance of 0.06µF or larger. A 0.10µF or larger X5R dielectric capacitor would be a good
choice. Under sizing the bootstrap capacitor will result in inadequate gate drive to the high-side switch.
INPUT CAPACITOR SELECTION
The input capacitor selection is based largely on ripple current capability. The instantaneous pulse currents
drawn by the power supply must be deliv-ered by the input capacitors. This is related to the fact that the input
power source, be it a battery pack or a wall adapter, will place a substantial impedance in series with the input
path. As such, their ability to deliver large, fast rise time current pulses is limited. The input capacitors need to
average these pulse currents and smooth the current demand placed on the source.
Ceramic capacitors offer a good combination of ripple current capability and voltage rating, however they tend to
do so with relatively low capacitance values. It’s also not uncommon to find wall adapters and batteries with
impedances on the order of several hundred milliohms. The result is that while cycle-by-cycle current demand
may be met, the input capacitor network cannot deliver enough energy to prevent significant amounts of voltage
ripple when the load current is varied at a low rate. In particular, if the load varies at a frequency in the 2kHz to
4kHz range, the resulting large variation in voltage observed at the power supply input will result in noticeable
audio noise being produced by the piezo electric effects that are characteristic of ceramic capacitors. There are
several ways to mitigate this problem. The first is to use physically small ceramic capacitors since they tend to be
less efficient noise generators. That, however, would tend to limit the amount of capacitance to an unacceptably
low value. The use of aluminum-poly type capacitors such as Sanyo’s Poscap series is a viable option as well.
They can provide adequate levels of capacitance with very good ripple current capability. The down side of this
solution is cost. Another possible approach is to use relatively large ceramic capacitors and add a relatively large
aluminum electrolytic capacitor to hold up the supply voltage. The ceramics deliver the high frequency pulse
currents while the bulk caps smooth the longer term variation. In general a few hundred microfarads is adequate
for this purpose. As long as the AC ripple voltage impressed on the ceramic capacitors is small, on the order of a
few tenths of a volt, the ceramic capacitors are not going to be excessively noisy.
For purposes of sizing the high frequency input decoupling, the RMS input ripple current must be estimated. The
input ripple current will be approximately 50% of the output current at a 50% duty factor and decrease as duty
factor drops. Figure 22 shows this relationship.
20
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
RIPPLE CURRENT, IOUT (%)
60
50
40
30
20
10
0
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
Figure 22. RMS Input Ripple Current as a Percentage of DC Output Current
So for a design that must operate at a steady state load current of 12A, with 1.4V out and 8V in, the RMS input
ripple current would be about 37% of 12A or 4.4A RMS. A sufficient number of capacitors must be connected in
parallel to handle this current. For capacitors rated at 1.5A each, a minimum of 3 would be required. If it’s
desired to add enough bulk capacitance to control the input’s low frequency ripple voltage, the characteristic
impedance of the input power source must be well understood.
Bypassing Considerations
The LM27213 should have its supply pin (24) well bypassed. Generally a 1µF capacitor connected between the
Vdd pin and the SGND pin (23), should be adequate. It’s a good idea to add a resistor of about 10Ω in series
with the input source to provide some decoupling from noise on the 5V rail. The LM27213’s own gate drive pulse
currents can corrupt the 5V rail enough to cause problems without this filter. There also needs to be a 1µF or
larger ceramic capacitor connected between the driver supply pin PVDD (48) and PGND (45). The bypass
capacitors should be located very close to the pins to provide a low inductance path. This is particularly important
for the PVDD bypass. This capacitor must supply all of the low-side gate drive pulse currents as well as the
charging current for the high-side bootstrap capacitor. It’s also a good idea to install a 0.1µF capacitor between
the VREF pin (11) and SGND. In addition, there should be small filter capacitors connected between the ILIM
and ILIMREF pins and the CMP and CMPREF pins. Typically, a 1200pF capacitor will prove adequate for this
purpose.
Current Sense Resistor
The maximum value allowed for the current sense resistor is a value equal to the desired load line slope.
Increasing beyond this value will make the load line excessively steep with no way to reduce the slope. Lower
values are permissible and values as low as 1mΩ have been used successfully. The regulator will have a
tendency to exhibit excessive amounts of pulse jitter if the sense resistor is too small since the current sense
signal is reduced as well. One way to mitigate this problem is to add a little filtering to the load line setting
resistor R2 in Figure 21. A typical time constant to shoot for is approximately 500ns. So for R2 = 100Ω,
something around a 4700pF capacitor should prove helpful. If this capacitor is made too large the result will be
large overshoot and undershoot in the response to load transients. See the section below on load line setting for
more information about choosing these resistors.
Load Line Setting Resistors
Resistors R1, R2, and the current sense resistor (see Figure 20) are used to control the slope of the load line. In
the simplest configuration R1 = 0 ohms and R2 is omitted. In this case the load line is nominally equal to the
current sense resistor value. For relatively low current designs this configuration can work acceptably well. At
higher current levels the DC drop across the power planes may well contribute an excessive error since the
distribution path between the sense resistor and the load is effectively in series with the current sense resistor,
and therefore, will steepen the load line. For designs with relatively steep load lines (3 mΩ) the power dissipation
is also excessive at high currents. The solution is to lower the sense resistor value and add the R1, R2 divider to
synthesize a steeper slope. The load line is calculated from:
LL = Rs x (1+R1/R2)
(16)
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
21
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
www.ti.com
Since the power plane resistance will increase the load line by an amount that’s nearly impossible to estimate
accurately, the simplest approach is to install the values calculated for the ideal, lossless power path, and run the
circuit. Record the no load and full load output voltage and calculate the load line impedance.
LL = (V0 – Vfull)/Ifull
where
•
•
•
V0 is the no load output voltage
Vfull is the full load output voltage
And Ifull is the full load current
(17)
Use this information along with the installed values of R1 and R2 to calculate the effective sense resistor value:
Rse = LL/(1+R1/R2)
(18)
Now using this value of sense resistor, recalculate a new value for R1:
R1 = R2(LL/Rse –1)
(19)
Installing these values for R1 and R2 should yield a nearly perfect load line.
Layout Guidelines
As is true for any high-current power supply design, care needs to be taken when doing an LM27213 layout. As
a general rule, it makes the most sense to start the layout by placing the power path components to connect in a
logical power flow. The input ceramic capacitors should be connected as close as physically possible to the
source of the low side FET and the drain of the high-side FET. The loop area enclosed by the input capacitors
and FETs needs to be minimized to control ringing and optimize the switch rise and fall times. A good practice is
to connect the FETs on the top side of the board with the bypass capacitors located immediately below on the
back side. The capacitors’ ground pads should be located directly beneath the low-side FET’s source pad and a
collection of vias used to hook the two together and at the same time tie to the internal ground plane. Figure on
allowing one amp of load current per via if the hole diameter is less than 15 mils and two Amps per via if greater
than 20 mils. More vias are almost always better than fewer.
Keep the switch node connection between the two FETs and the inductor as short and wide as possible. The
inductor should be located very close to the FETs. The inductor should then flow in to the sense resistor that
needs to be immediately adjacent to the processor decoupling capacitors.
The LM27213 needs to be located relatively close to the FETs to minimize the gate drive lengths. Also, route the
high-side gate signal (pin 2) and the SW pin (3) parallel to and very close to each other to minimize the
inductance of the loop enclosed. These traces should be at least 15 mils wide. The connections to the current
sense resistor must be made as Kelvin connections. Again, route these two traces in parallel if possible to
minimize noise susceptibility. The sense pin (16) is best connected to the core voltage near the center of the
CPU socket, but will in all likelihood work correctly if connected at the bypass capacitors located around the
periphery of the CPU socket. This line is the source of output voltage information for the over voltage protection
circuit and power good comparators.
Probably the most critical consideration for the controller is grounding. There are several ground-referenced pins
that need to be treated quite differently. A good practice is to tie the power ground pin (45) to the main power
plane with a single via. This pin is the ground connection for the gate drive and as such will carry very large
pulse currents. The bypass capacitor for DVDD should connect very close to this ground connection if at all
possible. DGND (13) is not particularly critical and should tie to the main ground plane as well. It only carries the
return currents for the digital portions of the controller, which are not very large. The SGND pin (23) is the most
critical and should also tie to the plane with a separate via close to PGND or directly to the PGND pin with a very
short trace. One grounding option is to define a signal ground plane that connects to ground through this point
only and resides under and around the IC. An alternative is to daisy chain a ground trace around the controller to
pick up all the signal ground referenced components while maintaining only a single connection to the ground
plane at the SGND pin. If doing the later and not defining signal ground as a separate net, it will not be possible
to use vias to connect to other layers unless your board layout package has the ability to isolate these vias from
the ground plane. Keeping the signal ground separate from the system ground plane ensures that signal ground
is “quiet” relative to all internal signals in the controller. The main ground plane is usually a very noisy
22
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
environment and not the absolute zero volt reference it tends to be thought of. Pains should be taken at every
opportunity to ensure that sources of large pulse currents into the ground plane are bypassed as well as possible
to minimize the disturbances to the ground plane. Under no circumstances should the controller be grounded at a
point between the low-side FET source connection and the input capacitor ground connection point. This is a
very noisy area.
Pin 5, SRCK, is the low-side FET source Kelvin connection and as the name implies needs to be connected
directly to the low side FET source pads. This pin is used as the reference potential for the diode emulator
circuit. If not connected correctly, the supply will behave erratically at light loads. The correct connection for
SRCK is to tie the pin to one of the vias connecting the low-side FET source to the internal ground plane on an
internal layer or the back side of the board. The trace need not be wide. A 10mil trace is adequate, as this line
carries essentially no current.
VCC5
R2
2.2
R1
10
D1
CMDSH-3
C2
4.7 PF
C1
1.0 PF
C3
0.22 PF
VDC
R9
2.2
U1
CBOOT
V1R7
VOVP
VBOOT
VSLP
DE_EN#
R4
VID0
VID1
VID2
VID3
VID4
VID5
CLK_EN#
VR_ON
XPOK
STP_CPU#
SLP
PGOOD
R5
4.53k
R6
7.5k
R7
1.21k
R8
100k
C11
15 PF
x6
L1
0.44 PH
HG
DE_EN#
VID0
VID1
VID2
VID3
VID4
VID5
CLK_EN#
VR_ON
XPOK
STP_CPU#
SLP
PGOOD
VDAC
VSTP
SGND
SS
C5
0.022 PF
+
SW
VCORE
R10 1
LG
LM27213
R3
0
C10
4.7 PF
x4
Q1
IRF660
8x2
DVDD
VDD
C9
1200 pF
Q2
IRF6618
x2
SRCK
PGND
R15
0.001
+
C12
22 PF
x 31
DGND
R11
ILIMREF
C13
330 PF
x3
100
C4
1200 pF
ILIM
SENSE
CM
VREF
CMPREF
R12
R13
C6
0.1 PF
C7
1200 pF
R14
150
100
C8
4700 pF
27A Core Supply
100
C10, TDK C3216X5R1E475K
C11, Sanyo 25 TQC15
C12, AVX 12066D226MAT
C13, Panasonic EEFSD0D330R
L1, Pulse Eng. PA0513
The circuit above is an example of a single phase supply at much higher current. The FETs chosen lend
themselves well to the use of a heatsink if desired. The transient response is quite good for a single phase
below, high current design as seen from the scope photo below.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
23
LM27213
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
24
www.ti.com
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
LM27213
www.ti.com
SNVS377A – FEBRUARY 2006 – REVISED MARCH 2013
REVISION HISTORY
Changes from Original (March 2013) to Revision A
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 23
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM27213
25
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM27213MTD/NOPB
ACTIVE
TSSOP
DGG
48
38
RoHS & Green
SN
Level-2-260C-1 YEAR
-5 to 110
27213MTD
LM27213MTDX/NOPB
ACTIVE
TSSOP
DGG
48
1000
RoHS & Green
SN
Level-2-260C-1 YEAR
-5 to 110
27213MTD
LM27213SQ/NOPB
ACTIVE
WQFN
RHS
48
250
RoHS & Green
SN
Level-2-260C-1 YEAR
-5 to 110
27213SQ
LM27213SQX/NOPB
ACTIVE
WQFN
RHS
48
2500
RoHS & Green
SN
Level-2-260C-1 YEAR
-5 to 110
27213SQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of