Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
LM3263 High-Current Step-Down DC-DC Converter With MIPI® RF Front-End
Control Interface for RF Power Amplifiers
1 Features
•
•
•
1
•
•
•
•
•
•
•
3 Description
The LM3263 is a DC-DC converter optimized for
powering multi-mode multi-band RF power amplifiers
(PAs) from a single lithium-ion cell. The LM3263
steps down an input voltage from 2.7 V to 5.5 V to a
dynamically adjustable output voltage of 0.4 V to
3.6 V. The output voltage is externally programmed
through the RFFE Digital Control Interface and is set
to ensure efficient operation at all power levels of the
RF PA.
®
MIPI RFFE Digital Control Interface
Operates from a Single Li-Ion Cell: 2.7 V to 5.5 V
Dynamically Adjustable Output Voltage: 0.4 V to
3.6 V (Typical) in PFM and PWM Modes
High-Efficiency PFM and PWM Modes With
Internal Seamless Transition
2.5-A Maximum Load Current in PWM Mode
2.7 MHz (Typical) Switching Frequency
ACB (Reduces Inductor Requirements and Size)
Internal Compensation
Current and Thermal Overload Protection
Very Small Solution Size: Approximately 9.1 mm2
When operating in pulse width modulated (PWM)
mode, the LM3263 produces a small and predictable
amount of output voltage ripple thus meeting the
power and stringent spectral-compliance needs of RF
PAs with minimal filtering and minimal excess
headroom. When operating in PFM mode, the
LM3263 enables the lowest current consumption
across PA output power level settings and therefore
maximizes system efficiency.
2 Applications
•
•
•
•
•
Smartphones
RF PC Cards
Tablets, eBook Readers
Handheld Radios
Battery-Powered RF Devices
The LM3263 has a unique Active Current assist and
analog Bypass (ACB) feature to minimize inductor
size without any loss of output regulation for the
entire battery voltage and RF output power range,
until dropout. ACB provides a parallel current path,
when needed, to limit the maximum inductor current
to 1.45 A (typical) while still driving a 2.5-A load. The
ACB feature also enables operation with minimal
dropout voltage.
Device Information(1)
PART NUMBER
LM3263
PACKAGE
DSBGA (16)
BODY SIZE (MAX)
2.049 mm × 2.049 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application
VBATT
2.7 V to 5.5 V
PVIN
PACB
SVDD
FB
1.8 V
RFFE
Master
VIO
ACB
Output Voltage
0.4 V to 3.6 V
SCLK
LM3263
SW
SDATA
2G
VCC_PA
GPO1
PA
BGND
SGND
PGND
3G/4G
VCC_PA
PA(s)
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
6
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
System Characteristics ............................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
7.1
7.2
7.3
7.4
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
12
13
13
17
7.5 Programming........................................................... 19
7.6 Register Map........................................................... 22
8
Application Information....................................... 24
8.1 Application Information............................................ 24
8.2 Typical Application ................................................. 24
9 Power Supply Recommendations...................... 26
10 Layout Considerations ....................................... 27
10.1 Layout Guidelines ................................................. 27
10.2 4. Layout Examples .............................................. 28
10.3 DSBGA Package Assembly and Use ................... 36
11 Device and Documentation Support ................. 37
11.1
11.2
11.3
11.4
11.5
11.6
Device Support......................................................
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
37
37
37
37
37
37
12 Mechanical, Packaging, and Orderable
Information ........................................................... 37
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (August 2013) to Revision B
Page
•
Added Device Information and Pin Configuration and Functions sections, ESD Ratings and Feature Description,
Device Functional Modes, Application and Implementation, Power Supply Recommendations, Layout, Device and
Documentation Support, and Mechanical, Packaging, and Orderable Information sections ................................................. 1
•
Added Thermal Information table with revised RθJA value (from 50°C/W to 77.1°C/W) and additional thermal values. ....... 4
Changes from Original (June 2013) to Revision A
•
2
Page
Added new inductor to recommended table......................................................................................................................... 36
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
5 Pin Configuration and Functions
YFQ Package
16-Pin DSBGA
Top View
YFQ Package
16-Pin DSBGA
Bottom View
PVIN
SW
PGND
ACB
A
A
ACB
PGND
SW
PVIN
PVIN
SW
BGND
PACB
B
B
PACB
BGND
SW
PVIN
VIO
SDATA
FB
ACB
C
C
ACB
FB
SDATA
VIO
SCLK
GPO1
SGND
SVDD
D
D
SVDD
SGND
GPO1
SCLK
1
2
3
4
4
3
2
1
Pin Functions
PIN
NAME
ACB
NUMBER
A4
C4
TYPE
DESCRIPTION
Output
ACB and analog bypass output. Connect to the output at the output filter capacitor.
ACB, analog bypass ground, and digital ground.
BGND
B3
Ground
FB
C3
Input
GPO1
D2
Output
General purpose output. Also used to reconfigure USID.
PACB
B4
Power
ACB power supply input
PGND
A3
Ground
Power ground to the internal NFET switch
Power
Power supply voltage input to the internal PFET switch
PVIN
A1
B1
Feedback analog input. Connect to the output at the output filter capacitor.
SCLK
D1
Digital/Input
Digital control interface RFFE Bus clock input. Typically connected to RFFE master on
RF or baseband IC. SCLK must be held low when VIO is not applied.
SDATA
C2
Digital
Input/Output
Digital control interface RFFE bus data input/output. Typically connected to RFFE
master on RF or baseband IC. SDATA must be held low when VIO is not applied.
SGND
D3
Ground
Signal analog ground (low current)
SVDD
D4
Power
Analog power supply voltage
Analog
Switching node connection to the internal PFET switch and NFET synchronous
rectifier.
SW
VIO
A2
B2
C1
Input
VIO functions as the RFFE interface reference voltage. VIO also functions as reset and
enable input to the LM3263. Typically connected to voltage regulator controlled by RF
or baseband IC.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
3
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
VBATT pins to GND (PVIN, SVDD, PACB to PGND, SGND, BGND)
FB, SW, GPO1, ACB, VIO, SDATA, SCLK
MIN
MAX
UNIT
–0.2
6
V
GND – 0.2 V
Continuous power dissipation (4)
See
Maximum lead temperature (soldering 10 seconds)
−65
Storage temperature, Tstg
(2)
(3)
(4)
V
Internally limited
Maximum operating junction temperature, TJ-MAX
(1)
(3)
150
°C
260
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the potential at the GND pins.
Abs Max for FB, SW, GPO1, ACB, VIO, SDATA, SCLK is the lessor of VIN + 0.2 V, or 6 V.
Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150°C (typical) and
disengages at TJ = 125°C (typical).
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±1000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±250
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
Input voltage range PVIN, SVDD, PACB
MAX
UNIT
2.7
5.5
V
1.65
1.95
V
0
2.5
A
Junction temperature, TJ
–30
125
°C
Ambient temperature, TA (1)
–30
90
°C
Input voltage range VIO
Recommended current load
(1)
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be de-rated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX). At higher power levels
duty cycle usage is assumed to drop (that is, maximum power 12.5% usage is assumed) for GSM/GPRS mode.
6.4 Thermal Information
LM3263
THERMAL METRIC (1)
YFQ (DSBGA)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
77.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
0.4
°C/W
RθJB
Junction-to-board thermal resistance
15.4
°C/W
ψJT
Junction-to-top characterization parameter
2.0
°C/W
ψJB
Junction-to-board characterization parameter
15.1
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
6.5 Electrical Characteristics
Unless otherwise noted, all limits apply to the Typical Application with VBATT = 3.8 V (= PVIN = SVDD = PACB), VIO = 1.8 V,
TJ = 25°C. (1) (2) (3)
PARAMETER
VFB,MIN
VFB,MAX
Feedback voltage at
minimum setting
Feedback voltage at
maximum setting
TEST CONDITIONS
MIN
VSET[7:0] = 1Bh, SMPS_CFG[5] = 1b
VSET[7:0] = 1Bh, SMPS_CFG[5] = 1b
−30°C ≤ TJ = TA ≤ 90°C
0.35
Shutdown supply current
IL-PWR
Low-power mode supply
current
IQ-PFM
PFM mode supply current
into SVDD
IQ PWM
PWM mode supply current
ILIM, PFET Transient
Positive transient peak
current limit
ILIM, PFET Steady-
Positive steady-state peak
current limit
ILIM, P-ACB
Positive active current assist
peak current limit
ILIM,NFET
NFET current limit
0.45
3.708
0.02
(4)
SW = 0 V, VIO = 0 V
−30°C ≤ TJ = TA ≤ 90°C
4
VSET[7:0] = 00h
No switching (5), SMPS_CFG[5] = 1b
360
No switching (5), SMPS_CFG[5] = 1b
−30°C ≤ TJ = TA ≤ 90°C
425
µA
1240
No switching (5), SMPS_CFG[5] = 0b
−30°C ≤ TJ = TA ≤ 90°C
1400
VSET[7:0] = 64h (6)
µA
1.9
VSET[7:0] = 64h (6)
−30°C ≤ TJ = TA ≤ 90°C
2.1
VSET[7:0] = 64h (6)
A
1.45
(6)
1.35
VSET[7:0] = 64h (6)
1.65
A
1.7
(6)
VSET[7:0] = 64h
−30°C ≤ TJ = TA ≤ 90°C
µA
µA
0.225
VSET[7:0] = 64h
−30°C ≤ TJ = TA ≤ 90°C
V
V
3.492
No switching (5), SMPS_CFG[5] = 0b
State
UNIT
3.6
SW = 0 V, VIO = 0 V (4)
ISHDN
MAX
0.4
VSET[7:0] = F0h, VBATT = 3.9 V,
SMPS_CFG[5] = 0b
VSET[7:0] = F0h, VBATT = 3.9 V,
SMPS_CFG[5] = 0b
−30°C ≤ TJ = TA ≤ 90°C
TYP
1.4
VSET[7:0] = A7h (6)
2
−1.5
VSET[7:0] = A7h
A
A
2.7
ƒOSC
Average Internal oscillator
frequency
IVIO-IN
VIO voltage average input
current
Average during a 26-MHz write
1.25
mA
VIORST
RFFE I/O voltage reset
voltage
VIO toggled low
0.45
V
IINVIO
VIO reset current
VIO = 0.45 V
−1
1
µA
IIN
SDATA, SCLK input current
VIO = 1.95 V
−1
1
µA
VIH
Input high-level threshold
SDATA, SCLK
0.4 × VIO
0.7 ×
VIO
V
VIL
Input low-level threshold
SDATA, SCLK
0.3 × VIO
0.6 ×
VIO
V
VIH-GPO
Input high-level threshold
GPO1
−30°C ≤ TJ = TA ≤ 90°C
VIL-GPO
Input low-level threshold
GPO1
−30°C ≤ TJ = TA ≤ 90°C
(1)
(2)
(3)
(4)
(5)
(6)
VSET[7:0] = A7h
−30°C ≤ TJ = TA ≤ 90°C
2.43
2.97
1.35
MHz
V
0.67
V
All voltages are with respect to the potential at the GND pins.
Minimum and Maximum limits are specified by design, test, or statistical analysis.
The parameters in Electrical Characteristics are tested under open loop conditions at PVIN = SVDD = PACB = 3.8 V.
Shutdown current includes leakage current of PFET.
IQ specified here is when the part is not switching.
Current limit is built-in, fixed, and not adjustable.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
5
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Electrical Characteristics (continued)
Unless otherwise noted, all limits apply to the Typical Application with VBATT = 3.8 V (= PVIN = SVDD = PACB), VIO = 1.8 V,
TJ = 25°C.(1)(2)(3)
PARAMETER
TEST CONDITIONS
VOH
Output high-level threshold
SDATA
ISDATA = 2 mA
VOL
Output low-level threshold
SDATA
ISDATA = –2 mA
VOH-GPO
Output high-level threshold
GPO
VOL-GPO
Output low-level threshold
GPO
VSET-LSB
Output voltage LSB
MIN
TYP
MAX
UNIT
VIO +
0.01
V
VIO ×
0.2
V
VIO – 0.15
VIO +
0.1
V
–0.4
0.3
V
VIO × 0.8
IOUT = ±200 µA
VSET[7:0] = A7h to A8h
15
mV
6.6 System Characteristics
The following spec table entries are specified by design and verifications providing the component values in the Typical
Application are used (L = 1.5 µH, DCR = 120 mΩ, TOKO DFE201610MT-1R5N, CIN = 10 µF, 6.3 V, 0402, Samsung
CL05A106MP5NUN, COUT = 10 µF + 4.7 µF + 3 × 1 µF; 10 V, 0402, Samsung CL05A106MP5NUN, CL05A475MPNRN;
6.3 V, 0201, TDK, C0603X5R0J105M). These parameters are not verified by production testing. Minimum and maximum
values are specified over the ambient temperature range TA = –30°C to +90°C. Typical values are specified at VBATT = 3.8 V
(= PVIN = SVDD = PACB), VIO = 1.8 V, SMPS_CFG = 20h, and TA = 25°C, unless otherwise stated.
PARAMETER
TON
TRESPONSE
TEST CONDITIONS
MIN
MAX
VBATT = 4.2 V, VSET[7:0] =00h to E3h,
VSET = 3.4 V, IOUT ≤ 1 mA
50
Time for VOUT to rise from 0.09 V to
3.4 V (3.07 V, 90% of delta VOUT
from the end of SCLK pulse)
VBATT = 3.8 V, RLOAD = 68 Ω
VSET[7:0] = 06h to E3h
SMPS_CFG[5] = 0b/1b
15
Time for VOUT to fall from 3.4 V to
0.09 V (0.42 V, 10% of delta VOUT
from the end of SCLK pulse)
VBATT = 3.8 V, RLOAD = 68 Ω
VSET[7:0] = E3h to 06h
SMPS_CFG[5] = 0b/1b
Time for VOUT to rise from 0.8 V to
3.3 V (3.05V, 90% of delta VOUT from
the end of SCLK pulse)
VBATT = 3.8 V, RLOAD = 20 Ω
VSET[7:0] =36h to DCh
7.4
12
Time for VOUT to fall from 3.3 V to 0.8
VBATT = 3.8 V, RLOAD = 20 Ω
V (1.05 V, 10% of delta VOUT from
VSET[7:0] = DCh to 36h
the end of SCLK pulse)
6.8
12
Time for VOUT to rise from 1.4 V to
3.4 V (3.2 V, 90% of delta VOUT from
the end of SCLK pulse)
µs
µs
10
Time for VOUT to fall from 3.4 V to 1.4
VBATT = 3.8 V, RLOAD = 6.8 Ω
V (1.6 V, 10% of delta VOUT from the
VSET[7:0] = E3h to 5Eh
end of SCLK pulse)
10
VBATT = 3.8 V, RLOAD = 2.2 Ω
VSET[7:0] = 78h to BBh
SMPS_CFG[5] = 0b
15
Time for VOUT to fall from 2.8 V to 1.8 VBATT = 3.8 V, RLOAD = 2.2 Ω
V (1.9 V, 10% of delta VOUT from the VSET[7:0] = BBh to 78h
end of SCLK pulse)
SMPS_CFG[5] = 0b
15
TBypass
Time for VSET to rise from 0.09V to
PVIN after BYPASS transition (90%)
VBATT = 3.6 V, IOUT ≤ 1 mA,
VSET[7:0] = 06h to FFh
Rtot-drop
Total dropout resistance in bypass
mode
VSET[7:0] = FAh, Max value at VBATT
= 3.1 V, Inductor DCR ≤ 151 mΩ
Submit Documentation Feedback
UNIT
15
VBATT = 3.8 V, RLOAD = 6.8 Ω
VSET[7:0] = 5Eh to E3h
Time for VOUT to rise from 1.8 V to
2.8 V (2.7 V, 90% of delta VOUT from
the end of SCLK pulse)
6
TYP
Turnon time (time for output to reach
95% of 3.4-V value from the end of
the SCLK pulse)
45
20
µs
55
mΩ
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
System Characteristics (continued)
The following spec table entries are specified by design and verifications providing the component values in the Typical
Application are used (L = 1.5 µH, DCR = 120 mΩ, TOKO DFE201610MT-1R5N, CIN = 10 µF, 6.3 V, 0402, Samsung
CL05A106MP5NUN, COUT = 10 µF + 4.7 µF + 3 × 1 µF; 10 V, 0402, Samsung CL05A106MP5NUN, CL05A475MPNRN;
6.3 V, 0201, TDK, C0603X5R0J105M). These parameters are not verified by production testing. Minimum and maximum
values are specified over the ambient temperature range TA = –30°C to +90°C. Typical values are specified at VBATT = 3.8 V
(= PVIN = SVDD = PACB), VIO = 1.8 V, SMPS_CFG = 20h, and TA = 25°C, unless otherwise stated.
PARAMETER
IOUT
IOUT,
PU
IOUT, PD,
PWM
IOUT,
MAX_PFM
Linearity
η
TEST CONDITIONS
Maximum load current in PWM mode
Switcher + ACB
Maximum output transient pullup
current limit
Switcher + ACB (1)
PWM maximum output transient
pulldown current limit
Switcher + ACB (1)
Maximum output load current in PFM
mode
VBATT = 3.8 V, VSET = 3.2 V
Linearity in control range of VSET =
0.4 V to 3.6 V
VBATT = 3.9 V (2), Monotonic in nature;
VSET[7:0] = 1Bh to F0h,
SMPS_CFG[5] = 0b
Efficiency
MIN
TYP
MAX
3
A
−3
60
mA
–3%
3%
–50
50
VBATT = 3.8 V, VSET= 0.5 V,
IOUT = 5mA
52%
56%
VBATT = 3.8 V, VSET= 1.8 V,
IOUT = 10 mA
78%
82%
VBATT = 3.8 V, VSET= 1.6 V,
IOUT = 130 mA
83%
89%
VBATT = 3.8 V, VSET = 2.5 V,
IOUT = 250 mA
90%
94%
VBATT = 3.8 V, VSET = 3.4 V,
IOUT = 550 mA
93%
95%
VBATT = 3.8 V, VSET = 1 V,
IOUT = 400 mA, SMPS_CFG[5] = 0b
81%
85%
VBATT = 3.8 V, VSET = 3.5 V,
IOUT = 1900 mA, SMPS_CFG[5] = 0b
89%
92%
2.7-MHz PWM normal operation
ripple
VBATT = 3.2 V to 4.3 V, VSET = 0.4 V
to 3.6 V, RLOAD = 1.9 Ω (3)
SMPS_CFG[5]= 0b
Ripple voltage at pulse skipping
condition
VBATT = 3.2 V, VSET = 3 V,
RLOAD = 1.9 Ω (3)
SMPS_CFG[5]= 0b
8
VBATT = 3.2 V, VSET = 3 V,
IOUT = 40 mA
50
VBATT = 3.2 V, VSET = 2.5 V,
IOUT = 10 mA
50
VBATT = 3.2 V, VSET< 0.5 V,
IOUT = 5 mA
50
VRIPPLE
PFM ripple voltage
UNIT
2.5
1
mV
3
mVpp
Line transient response
VBATT = 3.6 V to 4.2 V,
TR = TF = 10 µs,
VSET = 3.2 V,
IOUT = 500 mA
50
mVpk
Load_tr
Load transient response
VSET = 3 V,
TR = TF = 10 µs,
IOUT = 0 A to 1.2 A,
SMPS_CFG[5] = 0b
60
mVpk
Max Duty
Cycle
Maximum duty cycle
Line_tr
(1)
(2)
(3)
100%
Current limit is built-in, fixed, and not adjustable.
Linearity limits are ±3% or ±50 mV whichever is larger.
Ripple voltage must be measured at COUT electrode on a well-designed PC board using suggested inductor and capacitors.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
7
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
System Characteristics (continued)
The following spec table entries are specified by design and verifications providing the component values in the Typical
Application are used (L = 1.5 µH, DCR = 120 mΩ, TOKO DFE201610MT-1R5N, CIN = 10 µF, 6.3 V, 0402, Samsung
CL05A106MP5NUN, COUT = 10 µF + 4.7 µF + 3 × 1 µF; 10 V, 0402, Samsung CL05A106MP5NUN, CL05A475MPNRN;
6.3 V, 0201, TDK, C0603X5R0J105M). These parameters are not verified by production testing. Minimum and maximum
values are specified over the ambient temperature range TA = –30°C to +90°C. Typical values are specified at VBATT = 3.8 V
(= PVIN = SVDD = PACB), VIO = 1.8 V, SMPS_CFG = 20h, and TA = 25°C, unless otherwise stated.
PARAMETER
PFM_Freq
Minimum PFM frequency
TEST CONDITIONS
VBATT = 3.2 V, VSET = 1 V,
IOUT = 10 mA
VBATT = 3.2 V, VSET = 0.5 V,
IOUT = 5 mA
NSET
VSET DAC number of bits
Monotonic
TSETUP
Power-up time (time for RFFE bus
active after VIO applied)
VIO = Low to 1.65 V
TVIO-RST
VIO supply reset timing
VIO = 0.45 V
8
Submit Documentation Feedback
MIN
TYP
100
160
34
55
MAX
UNIT
KHz
8
Bits
50
10
ns
µs
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
6.7 Typical Characteristics
VBATT = 3.8 V, TA = 25°C, unless otherwise noted
10
450
VOUT = 1.0V @ PFM mode
INPUT CURRENT ( mA )
INPUT CURRENT (µA)
425
400
375
350
325
VOUT = 2.0V @ PWM Mode
8
6
4
2
0
300
2.5
3.0
3.5
4.0
4.5
INPUT VOLTAGE (V)
5.0
2.5
5.5
3.5
4.5
5.0
5.5
C002
No load
Figure 1. Input Current (PFM) vs Input Voltage
Figure 2. Input Current (PWM) vs Input Voltage
3.00
4.0
2.95
OUTPUT VOLTAGE ( V )
VOUT = 2.0V, IOUT = 500mA
2.90
2.85
2.80
2.75
2.70
2.65
2.60
3.5
VBATT = 4.2V
RLOAD = 6.8
3.0
2.5
2.0
1.5
1.0
0.5
0.0
2.55
0.0
0.5
1.0
2.50
2.5
3.0
3.5
4.0
4.5
5.0
INPUT VOLTAGE ( V )
5.5
22
43
C003
Figure 3. Average Switching Frequency vs Input Voltage
1.5
2.0
2.5
3.0
3.5
C8
EA
VSET VOLTAGE ( V )
64
86
A7
VSET_CTRL (hex)
4.0
C004
Figure 4. Output Voltage vs VSET_CTRL Setting
3.6
100
IOUT = 500mA
95
3.4
EFFICIENCY ( % )
OUTPUT VOLTAGE ( V )
4.0
INPUT VOLTAGE ( V )
No load
SWITCHING FREQUENCY ( MHz )
3.0
C001
3.2
3.0
IOUT = 1.5A
2.8
90
85
80
75
VOUT = 0.8V
VOUT = 1.0V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.0V
VOUT = 0.4V
70
65
2.6
60
2.5
3.0
3.5
4.0
4.5
5.0
INPUT VOLTAGE ( V )
5.5
0
25
VOUT = 3.4 V
50
75
100
125
OUTPUT CURRENT ( mA )
C005
Auto-PFM Mode
Figure 5. Output Voltage vs Input Voltage
Product Folder Links: LM3263
C006
IOUT = 10 mA to 150 mA
Figure 6. Efficiency vs Load Current
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
150
9
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Typical Characteristics (continued)
100
100
95
95
EFFICIENCY ( % )
EFFICIENCY ( % )
VBATT = 3.8 V, TA = 25°C, unless otherwise noted
90
85
VOUT = 1.6V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
80
75
90
85
VOUT = 1.6V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
80
75
70
70
100
200
300
400
500
600
700
800
OUTPUT CURRENT ( mA )
Auto-PFM Mode
100
200
IOUT = 150 mA to 750 mA
300
400
500
600
700
800
900 1,000
OUTPUT CURRENT ( mA )
C007
Forced PWM Mode
Figure 7. Efficiency vs Load Current
C008
IOUT = 100 mA to 1000 mA
Figure 8. Efficiency vs Load Current
100
VOUT (2V/DIV)
EFFICIENCY ( % )
95
90
85
SDATA (2V/DIV)
80
75
65
60
1.00
IOUT (500mA/DIV)
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.0V
VOUT = 3.5V
70
1.25
1.50
1.75
2.00
2.25
Forced PWM Mode
TIME ( 20µs/DIV )
2.50
OUTPUT CURRENT ( A )
C010
C009
IOUT = 1 A to 2.5 A
Auto PFM
RLOAD = 6.8 Ω
VOUT = 0.4 V to 3.4 V
Figure 9. Efficiency vs Load Current
Figure 10. VOUT Transient
VOUT (2V/DIV)
SDATA (2V/DIV)
VOUT
5mVac/DIV
IOUT
50mA/DIV
IOUT (1A/DIV)
TIME ( 20µs/DIV )
100 s/DIV
C011
Forced PWM
VOUT = 1.4 V to 3.4 V
RLOAD = 1.9 Ω
PFM Mode
IOUT= 0 mA to 60 mA
Figure 12. Load Transient
Figure 11. VOUT Transient
10
VOUT = 1 V
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
Typical Characteristics (continued)
VBATT = 3.8 V, TA = 25°C, unless otherwise noted
VOUT
50mVac/DIV VOUT
50mVac/DIV
IOUT
200mA/DIV IOUT
500mA/DIV
100 s/DIV
VOUT = 2.5 V
100 s/DIV
IOUT= 0 mA to 300 mA
VOUT = 3 V
Figure 13. Load Transient
IOUT= 0 mA to 700 mA
Figure 14. Load Transient
VOUT
100mVac/DIV VOUT
50mVac/DIV
IOUT
500mA/DIV VBATT
500mV/DIV
100 s/DIV
VBATT = 4.2 V
VOUT = 3 V
100 s/DIV
IOUT= 0 mA to 1.2 A
VBATT = 3.6 V to 4.2 V
Figure 15. Load Transient
VOUT = 2.5 V
RLOAD = 6.8 Ω
Figure 16. Line Transient
VOUT
1V/DIV
SW
2V/DIV
IIND
1A/DIV
50mVac/DIV
VOUT
500mV/DIV
VBATT
100 s/DIV
VBATT = 3.6 V to 4.2 V
VOUT = 1 V
20 s/DIV
RLOAD = 6.8 Ω
VBATT = 4.2 V
Figure 17. Line Transient
VOUT = 2.5 V
RLOAD = 6.8 Ω to 0 Ω
Figure 18. Timed-Current Limit
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
11
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
7 Detailed Description
7.1 Overview
The LM3263 is a high-efficiency step-down DC-DC converter optimized to power the RF power amplifier (PA) in
cell phones, portable communication devices, or battery-powered RF devices with a single litium-Ion battery. It
operates in modulated-frequency pulsed width modulation (PWM) mode for 2G transmissions (with MODE =
Forced PWM (PWM only), register 01h SMPS_CFG [5] set to 0b), automatic mode transition between pulse
frequency modulation (PFM) and PWM for 3G/4G RF PA operation (with MODE = Auto-PFM (PFM/PWM),
SMPS_CFG bit 5 set to 1b), or forced-bypass mode (with SMPS_CFG [4] set to 1b or REGISTER_0 [6:0] set to
7Fh or register 03h VSET_CTRL [7:0] set to FEh-FFh). Power states are also in provided shutdown, low power,
standby, and active modes. The DC-DC converter operates at active mode. Please see Figure 21 and Register
Map.
PWM mode provides high efficiency and very low output-voltage ripple. In PWM-mode operation, the modulated
switching frequency helps to reduce RF transmit noise. In PFM mode, the converter operates with reduced
switching frequencies and lower supply current to maintain high efficiencies. The forced-bypass mode allows the
user to drive the output directly from the input supply through a bypass FET. The shutdown mode turns the
LM3263 off and reduces current consumption to 0.02 µA (typical).
In the PWM and PFM modes of operation, the output voltage of the LM3263 can be dynamically programmed
from 0.4 V to 3.6 V (typical) by setting the VSET register. Current overload protection and thermal overload
protection are also provided.
The LM3263 was engineered with Active Current assist and analog Bypass (ACB). This unique feature allows
the converter to support maximum load currents of 2.5 A (minimum) while keeping a small footprint inductor and
meeting all of the transient behaviors required for operation of a multi-mode RF PA. The ACB circuit provides an
additional current path when the load current exceeds 1.45 A (typical) or as the switcher approaches dropout.
Similarly, the ACB circuit allows the converter to respond with faster VSET output voltage transition times by
providing extra output current on rising and falling output edges. The ACB circuit also performs the function of
analog bypass. Depending upon the input voltage, output voltage, and load current, the ACB circuit automatically
and seamlessly transitions the converter into analog bypass, while maintaining output voltage regulation and low
output voltage ripple. Full bypass (100% duty cycle operation) occurs if the total dropout resistance in bypass
mode (Rtot_drop = 45 mΩ) is insufficient to regulate the output voltage.
The device 16-pin DSBGA package is the best solution for space-constrained applications such as cell phones
and other hand-held devices. The high switching frequency, 2.7 MHz (typical) in PWM mode, reduces the size of
input capacitors, output capacitor, and of the inductor. Use of a DSBGA package is best suited for opaque case
applications and requires special design considerations for implementation (see Layout Considerations).
12
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
7.2 Functional Block Diagram
GPO1
SDATA SCLK
VIO
Q-MIPI Compliant
RFFE
VSET
DAC
Error
Amplifier
SVDD
PVIN
PACB
Active Current
Assist and
Analog
Bypass (ACB)
ACB
+
FB
Internal Loop
Compensation
-
SW
1.9 A
Gate Drive Circuits
ENABLE
Control Logic
CLK PWM
RAMP
SW
+
-
Current Limit
Protection
Thermal Protection
PGND
SGND
BGND
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 PWM Operation
The LM3263 operates in PWM mode when forced-PWM mode operation is selected (SMPS_CFG [5] set to 0b).
The switching frequency is modulated, and the switcher regulates the output voltage by changing the energy per
cycle to support the load required. During the first portion of each switching cycle, the control block in the
LM3263 turns on the internal PFET switch. This allows current to flow from the input through the inductor and to
the output filter capacitor and load. The inductor limits the current to a ramp with a slope of (VBATT – VSET)/L, by
storing energy in its magnetic field.
During the second portion of each cycle, the control block turns the PFET switch off, blocking current flow from
the input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the
NFET and to the output filter capacitor and load, which ramps the inductor current down with a slope of –VSET/L.
The output filter capacitor stores charge when the inductor current is greater than the load current and releases it
when the inductor current is less than the load current, smoothing the voltage across the load.
At the next rising edge of the clock, the cycle repeats. An increase of load pulls the output voltage down,
increasing the error signal. As the error signal increases, the peak inductor current becomes higher therefore
increasing the average inductor current. The output voltage is therefore regulated by modulating the PFET switch
on time to control the average current sent to the load. The circuit generates a duty-cycle modulated rectangular
signal that is averaged using a low pass filter formed by the inductor and output capacitor. The output voltage is
equal to the average of the duty-cycle modulated rectangular signal.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
13
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Feature Description (continued)
7.3.2 PFM Operation
When auto-PFM mode operation is selected (SMPS_CFG [5] set to 1b), the LM3263 automatically transitions
from PWM operation into PFM operation if the average inductor current is less than 60 mA (minimum) and the
difference between VBATT – VSET ≥ 0.6 V. The switcher regulates the fixed output voltage by transferring a fixed
amount of energy during each cycle and modulating the frequency to control the total power delivered to the
output. The converter switches only as needed to support the demand of the load current, therefore maximizing
efficiency. If there is an increase in load current during PFM mode to more than 120 mA (typical), the part
automatically transitions into PWM mode. A 20 mA (typical) hysteresis window exists between PFM and PWM
transitions. After a transient event, the part temporarily operates in PWM mode to quickly charge or discharge the
output. This is true for start-up conditions or if the mode operation is changed from forced-PWM to auto-PFM
mode (SMPS_CFG [5] toggled from 0b to 1b). Once the output reaches its target output voltage, and the load is
less than 60 mA (minimum), then the device seamlessly transitions into PFM mode (assuming the device is not
in forced-bypass condition).
7.3.3 Active Current Assist and Analog Bypass (ACB)
The 3GPP time mask requirement for 2G requires high current to be sourced by the LM3263. These high
currents are required for a small time during transients or under a heavy load. Overrating the switching inductor
for these higher currents increases the solution size and is not an optimum solution. Thus, to allow an optimal
inductor size for such a load, an alternate current path is provided from the input supply through the ACB pin.
Once the switcher current limit ILIM,PFET,SteadyState is reached, the ACB circuit starts providing the additional current
required to support the load. The ACB circuit also minimizes the dropout voltage by having the analog bypass
FET in parallel with VSET. The LM3263 can provide up to 2.5 A (minimum) of current in bypass mode.
7.3.4 Bypass Operation
The bypass circuit provides an analog bypass function with very low dropout resistance (Rtot_drop = 45 mΩ
typical). When SMPS_CFG [4] is set to 0b, the part is in automatic bypass mode which automatically determines
the amount of bypass needed to maintain voltage regulation. When the input supply voltage to the LM3263 is
lowered to a level where the commanded duty cycle is higher than what the converter is capable of providing, the
part goes into pulse-skipping mode. The switching frequency is reduced to maintain a low and well behaved
output voltage ripple. The analog bypass circuit allows the converter to stay in regulation until full bypass is
reached (100% duty cycle operation). The converter comes out of full bypass and back into analog bypass
regulation mode with a similar reverse process.
To operate the device at the Forced-Bypass mode, set REGISTER_0 to 7Fh or VSET_CTRL to FEh-FFh.
7.3.5 Dynamic Adjustment of Output Voltage
The LM3263 can be dynamically programmed to an output voltage from 0.4 V to 3.6 V with 30 mV or 15 mV
steps. REGISTER_0 [6:0] is set to 0Dh to 78h with 30-mV output voltage steps, and VSET_CTRL [7:0] is set to
1Bh to F0h with 15-mV steps. Although the output voltage can be programmed lower than 0.4 V and higher than
3.6 V by setting the registers, the device might suffer from larger output ripple voltage, higher current limit
operation, and decreased linearity.
7.3.6 DC-DC Operating Mode Selection
Programming SMPS_CFG [5] changes the state of the converter to one of the two allowed modes of operation.
SMPS_CFG [5] default is 0b, and the device operates in forced-PWM mode (PWM only). Setting the register bit
to 1b sets the device for automatic transition between PFM/PWM mode operation. In this mode, the converter
operates in PFM mode to maintain the output voltage regulation at very light loads and transitions into PWM
mode at loads exceeding 120 mA (typical). Setting the register bit to 0b sets the device for PWM mode
operation. The switching operation is in PWM mode only, and the switching frequency is also 2.7 MHz (typical).
The device operates in forced-bypass mode when SMPS_CFG [4] is set to 1b.
For typical operation mode is set to auto-PFM and auto-bypass modes by setting SMPS_CFG = 20h.
Table 1 shows the LM3263 parameters for the given modes.
14
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
Feature Description (continued)
Table 1. Parameters Under Different Modes Of Operation
(1)
SMPS_CFG [5] MODE
SMPS_CFG [4] BYPS
IOUT CONDITIONS
0
0
X
OPERATION MODE
Forced PWM
X (1)
1
X
Forced bypass
1
0
IOUT ≤ 60 mA
PFM
1
0
60 mA < IOUT ≤ 120 mA
PFM or PWM
1
0
IOUT > 120 mA
PWM
don't care
7.3.7 Internal Synchronous Rectification
The LM3263 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop, thus
increasing efficiency. The reduced forward voltage drop in the internal NFET synchronous rectifier significantly
improves efficiency for low output voltage operation. The NFET is designed to conduct through its intrinsic body
diode during the transient intervals, eliminating the need of an external diode.
7.3.8 Current Limit
The LM3263 current limit feature protects the converter during current overload conditions. Both SW and ACB
pins have positive and negative current limits. The positive and negative current limits bound the SW and ACB
currents in both directions. The SW pin has two positive current limits. The ILIM,PFET,SteadyState current limit triggers
the ACB circuit. Once the peak inductor current exceeds ILIM,PFET,SteadyState, the ACB circuit starts assisting the
switcher and provides just enough current to keep the inductor current from exceeding ILIM,PFET,SteadyState allowing
the switcher to operate at maximum efficiency. Transiently a second current limit (ILIM,PFET,Transient) of 1.9 A
(typical, 2.1 A maximum) limits the maximum peak inductor current possible. The output voltage falls out of
regulation only after both SW and ACB output pin currents reach their respective current limits of ILIM,PFET,Transient
and ILIM,P-ACB.
7.3.9 Timed Current Limit
If the load or output short-circuit pulls the output voltage to 0.3 V or lower, and the peak inductor current sustains
ILIM,PFET,SteadyState more than 10 µs, the LM3263 switches to a timed current limit mode. In this mode, the internal
PFET switch is turned off. After approximately 30 µs, the device returns to the normal operation.
7.3.10 Thermal Overload Protection
The LM3263 device has a thermal overload protection that protects itself from short-term misuse and overload
conditions. If the junction temperature exceeds 150°C, the LM3263 shuts down. Normal operation resumes after
the temperature drops below 125°C. Prolonged operation in thermal overload condition may damage the device
and is therefore not recommended.
7.3.11 Start-Up
The waveform in Figure 19 shows the start-up sequence and sample conditions. First, VBATT
(=PVIN=SVDD=PACB) must take on a value from 2.7 V to 5.5 V. After VBATT is ensured to be beyond 2.7 V,
VIO can be set 1.8 V. Next, setting PM_TRIG [7:6] to 38h enables active mode. Finally, VSET can be
programmed to a value that corresponds to the desired output voltage. The LM3263 output voltage then goes to
the programmed VSET value. To optimize the start-up time and behavior of the output voltage, the LM3263
starts up in PWM mode even when the operating mode selected is auto-PFM mode (SMPS_CFG [5] set to 1b) if
the output load current is ≤ 60 mA (minimum), the LM3263 then seamlessly transitions into PFM mode.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
15
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
Shutdown
www.ti.com
Low Power
Initialization
Active
APT
150 ns (min)
50 Ps max
5 Ps (min)
25 Ps max
VBATT
t0
VBATT applied, VIO = 0V.
LM3263 in Shutdown.
t1
VIO applied.150 ns later LM3263 is in
Low Power and RFFE configuration
writes may occur. Trigger Mask Bits
are set.
t2
VSET is programmed and takes effect
immediately. LM3263 initializes and
powers up internal circuit blocks.
t3
DC-DC is active in normal mode.
t4
Transmit Slot Boundary. DC-DC
output settled (95%).
VIO
SDATA
3.4V
0V
VOUT
SW
t0
t1
t3
t2
RFFE write
PM_TRIG
(Reg 1Ch = 38h)
t4
RFFE write
VSET = DC-DC VOUT
(Reg 03h = E3h)
RFFE write
SMPS_CFG= auto PFM
(Reg 01h = 20h)
Figure 19. Non-Triggered Start-Up Sequence
Shutdown
Low Power
Initialization
Active
APT
5 Ps (min)
150 ns (min)
50 Ps max
25 Ps max
VBATT
t0
VBATT applied, VIO = 0V.
LM3263 in Shutdown.
t1
VIO applied.150ns later
LM3263 is in Low Power, and
RFFE configuration writes may
occur.
t2
Trigger is programmed. VSET and
SMPS_CFG loaded from shadow
registers. LM3263 initializes and
powers up internal circuit blocks.
t3
DC-DC is active in normal mode.
t4
Transmit Slot Boundary. DC-DC
output settled (95%).
VIO
SDATA
3.4V
VOUT
0V
SW
t0
t1
t2
RFFE write
SMPS_CFG= auto PFM
(Reg 01h = 20h)
RFFE write
VSET = DC-DC VOUT
(Reg 03h = E3h)
t3
t4
RFFE write
PM_TRIG
(Reg 1Ch = 02h)
Figure 20. Triggered Start-Up Sequence
16
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
7.4 Device Functional Modes
7.4.1 Shutdown Mode
Shutdown mode is entered whenever the voltage on the VIO pin is 0 V. The communications and the controls
are not powered. In this mode, the current consumption is 0.02 µA (typical).
7.4.2 Low-Power Mode
Low-power mode is the initial default state when VIO is applied. In this mode, the DC-DC is disabled, and its SW
is tri-state. The current consumption is minimized 0.225 µA (typical). This mode can be entered by programming
any one of three registers below:
• Register 00h REGISTER_0 [6:0] to 00h;
• Register 03h VSET_CTRL[7:0] to 00h or 01h;
• Register 1Ch PM_TRIG [7:6] to 10b.
7.4.3 Standby Mode
In standby mode, switching is stopped, and the output power FETs are placed are tri-state. The standby mode
can be entered by setting PM_TRIG [7:6] and REGISTER_0 or VSET_CTRL registers.
• Register 00h REGISTER_0 [6:0] to 02h;
• Register 03h VSET_CTRL [7:0] to 04h or 05h;
• Register 1Ch PM_TRIG [7:6] to 00b.
7.4.4 Active Mode
The active mode is a DC-DC converter operating mode that allows the device to function, process RFFE
commands, and respond to RFFE commands. This mode can be entered by setting register 1Ch PM_TRIG [7:6]
to 00b. Once the device is the active Mode, the DC-DC converter operating mode and the output voltage can be
programmed by using REGISTER_0 [6:0] and VSET_CTRL[7:0] registers.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
17
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Device Functional Modes (continued)
7.4.5 User States
VIO = Low
VIO = Low
Shutdown
O
VI
VIO = High
=
Lo
w
PM_T= 38h
and
VC= 04h or 05h
PM_T= 40h
Low Power
Standby
PM_T= 80h or 40h
or
VC= 00h or 01h
PM_T= 80h or 40h
or
VC= 00h or 01h
VC= 04h or 05h
PM_T= 38h
and
VC { 06h
VC{ 06h
Active
VIO = Low
PM_T = PM_TRIG [7:0]
VC = VSET_CTRL [7:0]
SMPS_CFG[5]= 0b
and
VC= 1Bh to F0h
SMPS_CFG[5]= 1b
and
VC= 1Bh to F0h
Forced PWM mode
SMPS_CFG[4]= 1b
or
VC= FEh or FFh
Auto-PFM mode
Forced Bypass
mode
Specified output voltage range is 0.4 V to 3.6 V.
Writing to and reading back from REGISTER_0 and VSET_CTRL access the same internal VSET register. Writing to
VSET_CTRL programs the full 8 bits VSET value. Writing to REGISTER_0 programs 7 MSB of VSET with LSB set to
zero. When REGISTER_0 is written, the internal VSET register LSB bit[0] always takes a value of 0 and subsequent
read of VSET_CTRL bit[0] is read back as 0.
Figure 21. LM3263 User State Diagram
18
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
7.5 Programming
7.5.1 RFFE Interface
The digital control serial bus interface provides MIPI RF front-end control Interface compatible access to the
programmable functions and registers on the device. The LM3263 uses a three-pin digital interface: two for
bidirectional communications between the IC’s connected to the bus, along with an interface voltage reference
VIO that also acts as asynchronous enable and reset. When VIO voltage supply is applied to the bus, it enables
the Slave interface and resets the user-defined Slave registers to the default settings. The LM3263 can be set to
shutdown mode via the asynchronous VIO signal or low-power mode by setting the appropriate register via the
serial bus interface. The two communication lines are serial data (SDATA), and clock (SCLK). SCLK and SDATA
must be held low until VIO is present. The LM3263 connects as slave on a single-master serial bus interface.
The SDATA signal is bidirectional, driven by the Master or a Slave. Data is written on the rising edge (transition
from logical level zero to logical level one) of the SCLK signal by both Master and Slaves. Master and Slave both
read the data on the falling edge (transition from logical level one to logical level zero) of the SCLK signal. A
logic-low level applied to VIO signal powers off the digital interface.
7.5.2 Supported Command Sequences
SCLK
SA3
SDATA
SA2
SSC
SA1
SA0
1
D6
D5
D4
D3
Slave Address
D2
D1
P
D0
0
Parity
Data
Bus
Park
Signal driven by Master.
Signal not driven; pull-down only.
For reference only.
Figure 22. Register 0 Write
SCLK
A
SDATA
SA3
SA2
SA1
SA0
0
SSC
1
0
A4
A3
A2
A1
A0
P
Register Write Command Frame
SCLK
A
SDATA
P
D7
D6
D5
D4
D3
D2
Data Frame
D1
D0
P
0
Bus
Park
Signal driven by Master.
Signal not driven; pull-down only.
For reference only.
Figure 23. Register Write
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
19
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Programming (continued)
SCLK
A
SDATA
SA3
SA2
SA1
SA0
0
SSC
1
1
A4
A3
A2
A1
A0
P
Register Read Command Frame
SCLK
A
SDATA
P
0
D7
D6
D5
D4
D3
D2
D1
Data Frame (from Slave)
Bus
Park
D0
P
0
Bus
Park
Signal driven by Master.
Signal driven by Slave.
Signal not driven; pulldown only.
For reference only.
Figure 24. Register Read
7.5.3 Device Enumeration
The interface component recognizes broadcast Slave Address (SID) of 0000b and is configured, via internal
interface signals, with a unique SID address (USID) and a group SID address (GSID). The USID is set to 0100b
and GSID set to 0000b. The register-set component typically sets the USID to a fixed value; however, it is also
possible to select a second pre-set USID if a second LM3263 device is needed on the board. This second User
ID can be set by forcing a voltage > 1.36 V at the GPO1 pin for USID = 0101b. Refer to GPO1 for detailed usage
and programmability of the USID. The USID can also be re-programmed via the standard protocol for
programming the RFFE as defined in the RFFE spec. The USID must not be programmed to the reserved
broadcast slave id of 0000b. A value of 0000b is ignored by the device.
7.5.4 GPO1
GPO1 has two functions. The first function is an input to select the default USID, and the second function is to be
a general purpose output.
The state of the GPO1 pin at start-up determines the default USID. If the GPO1 pin is low or left floating at startup, the USID is 0100b. If the GPO1 pin is high at start-up, the USID is 0101b. One method to set the GPO1 pin
high is to place a pullup resistor (39 KΩ) on the GPO1 pin.
When the GPO1 pin is used as the general purpose output, GPO_CTRL [6] must be set to 1b. Once it has been
enabled as the general purpose output, GPO_CTRL [7] determines the state driven to the GPO1 pin. The pullup
resistor must be placed either as an external pullup on the board or through an internal pullup on the general
purpose input which is tied to the GPO1 pin.
The GPO1 pin can be left floating if unused.
7.5.5 Trigger Registers
Trigger registers are indicated in the RFFE register map by the Trigger column. All trigger registers are tied to
each of the TRIG_0-2 register bits. When a trigger register is written directly across the RFFE interface, the new
value is not loaded into the register until one of the TRIG0-2 register bits is written with a 1 and the associated
TRIG_MSK_x bit for that TRIG_x is not set. (Triggers are ignored when their associated masking bit is set.)
When all 3 TRIG_MSK_0-2 bits are set (all triggers are masked) the trigger feature is disabled, and any trigger
registers are loaded directly at the time of the write operation to that register rather than waiting for a trigger
event to update.
20
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
Programming (continued)
7.5.6 Control Interface Timing Parameters
TSCLKOTR
TSCLKOTR
TSCLKOH
TSCLKOL
VOHmin
SCLK
VOLmax
Figure 25. Clock Timing
VTPmax
SCLK
VTNmin
TD
TSDATAOTR
TD
TS
TH
TSDATAOTR
TS
TH
VTPmax
SDATA
VTNmin
Figure 26. Setup and Hold Timing
PARAMETER
TCLK
Clock time period
TSCLKOH
MIN
TYP
MAX
UNIT
38.5
ns
Clock high time
11.25
ns
TSCLKOL
Clock low time
11.25
ns
TS
Data setup time
1
ns
TH
Data hold time
5
ns
TD-Forward
Time for data output valid from SCLK rising edge
10.25
ns
TD-Reverse
Time for data output valid from SCLK rising edge
22
ns
TSDATAOTR
SDATA output transition (rise/fall) time
6.5
ns
2.1
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
21
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
7.6 Register Map
Addr
Register Contents
00h
REGISTER _0
Bits
Function
Default
Trigger*
R/W
7
RSVD
0
N/A
N/A
Reserved
R/W
Register 00h interacts with Register 03h.
DC-DC converter mode and output voltage control bits
00h : Low-power mode
01h : Reserved
02h : Standby mode
03h to 7Eh : active mode, setting output voltage is
enabled. Output voltage can be set 0.4 V to 3.6 V by
0Dh to 78h with 30-mV steps
7Fh : Forced-bypass mode
VSET[7:1] (dec) = Desired VOUT / 0.03 (round up
decimals), then converts a decimal number to
hexadecimal.
6:0
VSET[7:1]
00h
Yes
Bits
Function
Default
Trigger*
R/W
7:6
RSVD
0
N/A
N/A
Reserved
5
MODE
0
Yes
R/W
Switching mode select bit
0: Forced-PWM mode (PWM only)
1: Auto-PFM mode (PFM/PWM)
4
BYPS
0
Yes
R/W
Forced bypass bit
0: Auto-bypass mode
1: Forced-bypass mode
3:0
RSVD
0h
N/A
N/A
Reserved
Bits
Function
Default
Trigger*
01h
SMPS_CFG
02h
Description
GPO_CTRL
R/W
Description
7
GPO1_OUT
0
Yes
R/W
GPO1 output control
0: Low state
1: High state
6
GPO1_MODE
0
Yes
R/W
GPO1 Mode Selection
0 : General Purpose Output disabled
1 : General Purpose output driven by GPO1_OUT
5:0
RSVD
00h
N/A
N/A
Reserved
03h
VSET_CTRL
Bits
Function
Default
Trigger*
7:0
VSET[7:0]
00h
Yes
Bits
Function
Default
Trigger*
1Ah
R/W
Description
R/W
DC-DC converter mode and output voltage fine control
bits
00h-01h : Low-power mode
02h-03h : Reserved
04h-05h : Standby mode
06h to FDh : Active mode, setting output voltage is
enabled. Output voltage can be set 0.4 V to 3.6 V by
1Bh to F0h with 15-mV steps
FEh-FFh : Forced bypass mode
VSET[7:0] (dec) = Desired VOUT / 0.015 (round up
decimals), then converts a decimal number to
hexadecimal.
RFFE_STATUS
7
6
5
4
22
Description
R/W
Description
SWRESET
0
No
Software Reset. A write to 1 causes all registers except
for USID to be reset. Always reads back 0.
CMD_FRAME_PERR
0
No
Set if parity error detected in command frame. Cleared
on read. Write has no effect on this bit.
CMD_LENGTH_ERR
0
No
Error when transaction interrupted by new SSC.
Cleared on read. Write has no effect on this bit.
RSVD
0
No
Reserved
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
Register Map (continued)
Addr
Register Contents
3
DATA_FRAME_PERR
0
No
Write data frame parity error. Cleared on read. Write
has no effect on this bit.
RD_UNUSED_REG
0
No
Read command to an invalid register. Cleared on read.
Write has no effect on this bit.
WR_UNUSED_REG
0
No
Write command to an invalid register. Cleared on read.
Write has no effect on this bit.
BID_GID_ERR
0
No
Read command with a broadcast ID or Group ID.
Cleared on read. Write has no effect on this bit.
Bits
Function
Default
Trigger*
R/W
7:4
RSVD
0h
N/A
N/A
3:0
GSID
0h
No
2
1
0
1Bh
GROUP_ID
Description
Reserved
Group slave ID
1Ch
PM_TRIG
Bits
Function
Default
Trigger*
R/W
7:6
PWR_MODE
10b
No
5
TRIG_MSK_2
0
No
Mask bit for Trigger 2. Broadcast write to this bit is
ignored.
4
TRIG_MSK_1
0
No
Mask bit for Trigger 1. Broadcast write to this bit is
ignored.
3
TRIG_MSK_0
0
No
Mask bit for Trigger 0. Broadcast write to this bit is
ignored.
2
TRIG_2
0
No
Write to a 1 loads trigger registers with last written
value TRIG_MSK_2 is cleared. Write to 0 has no affect.
1
TRIG_1
0
No
Write to a 1 loads trigger registers with last written
value TRIG_MSK_1 is cleared. Write to 0 has no effect.
0
TRIG_0
0
No
Write to a 1 loads trigger registers with last written
value TRIG_MSK_0 is cleared. Write to 0 has no effect.
Bits
Function
Default
Trigger*
1Dh
R/W
Description
Power Mode Bits.
00b = Active mode
01b = Restore default settings
10b = Low-power mode
11b = Reserved
PRODUCT ID
7:0
PRODUCT_ID
82h
No
Bits
Function
Default
Trigger*
1Eh
R/W
R
Description
Product Identification Bits. Product ID default value
cannot be overwritten.
MANUFACTURER ID, LSB
R/W
7:0
MANID[7:0]
02h
No
Bits
Function
Default
Trigger*
R/W
7:6
RSVD
00b
N/A
N/A
5:4
MANID[5:4]
01b
No
R
1Fh
R
Description
Manufacturer Identification, bits 7:0. Manufacturer ID
default value cannot be overwritten.
MANUFACTURER ID, MSB
3:0
USID
010xb
No
Description
Reserved
Manufacturer Identification, bits 5:4. Manufacturer ID
default value cannot be overwritten.
Unique Slave Identifier. Bit 0 (x) of USID is tied to the
state of the GPO1 pin.
0100b: GPO1= Low state or floating
0101b: GPO1= High state
* Trigger = Yes: When all PM_TRIG.TRIG_MSK_* bits are set 1, REGISTER_0 is written immediately during a
write operation. If any PM_TRIG.TRIG_MSK_* bits are cleared (0), REGISTER_0 is not updated to the new
value after a write operation only after an unmasked PM_TRIG.TRIG_* bit is subsequently written to a 1.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
23
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
8 Application Information
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM3262 DC-DC converter steps down an input voltage from 2.7 V to 5.5 V to a dynamically adjustable
output voltage of 0.4 V to 3.6 V.
8.2 Typical Application
VBATT
2.7 V to 5.5 V
10 µF
0.1 µF
PVIN
PACB
SVDD
FB
VIO
1.8 V
RFFE
Master
ACB
Output Voltage
0.4 V to 3.6 V
1.5 µH
SCLK
LM3263
SW
SDATA
10 µF
3.3 nF
2G
VCC_PA
GPO1
4.7 µF
PA
BGND
SGND
PGND
3 x 1 µF
3G/4G
VCC_PA
PA(s)
Copyright © 2016, Texas Instruments Incorporated
Figure 27. LM3263 Typical Application
8.2.1 Design Requirements
For typical DC-DC converter applications use the parameters listed in Table 2.
Table 2. Design Parameters
24
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
2.7 V to 5.5 V
Output voltage range
0.4 V to 3.6 V
Output current
1A
Minimum effective output capacitance (including effects of AC bias, DC bias,
temperature)
10 µF
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
8.2.2 Detailed Design Procedure
8.2.2.1 Recommended External Components
8.2.2.1.1 Inductor Selection
A 1.5-µH inductor is needed for optimum performance and functionality of the LM3263. In the case of 2G
transmission current bursts, the effective overall RMS current requirements are reduced. Therefore, consult with
the inductor manufacturers to determine if some of their smaller components are suitable even if the inductor
specification does not appear to meet the LM3263 RMS current specifications.
The LM3263 automatically manages the inductor peak and RMS current (or steady-state current peak) through
the SW pin. The SW pin has two positive current limits. The first is the 1.45-A typical (or 1.65-A maximum)
overcurrent protection. It sets the upper steady-state inductor peak current (as detailed in Electrical
Characteristics ILIM,PFET,SteadyState). It is the dominant factor limiting the inductors ISAT requirement. The second is
an over-limit current protection. It limits the maximum peak inductor current during large signal transients (for
example, < 20 µs) to 1.9 A typical (or 2.1 A maximum). A minimum inductance of 0.3 µH must be maintained at
the second current limit.
The ACB circuit automatically adjusts its output current to keep the steady-state inductor current below the
steady-state peak current limit. Thus, the inductor RMS current is always effectively than the ILIM,PFET,SteadyState
during the transmit burst. In addition, as in the case with 2G where the output current comes in bursts, the
effective overall RMS current would be much lower.
For good efficiency, resistance of the inductor must be less than 0.2 Ω; TI recommends low-DCR inductors (< 0.2
Ω). Table 3 suggests some inductors and their suppliers.
Table 3. Suggested Inductors And Their Suppliers
MODEL
DFE201610C1R5N
(1285AS-H-1R5M)
LQM2MPN1R5MGH
MAKK2016T1R5M
VLS201610MT-1R5N
LQM21PN1R5MGH
VENDOR
DIMENSIONS
ISAT
(30% DROP IN
INDUCTANCE)
DCR
TOKO
2 mm × 1.6 mm × 1 mm
2.2 A
120 mΩ
Murata
2 mm × 1.6 mm × 1 mm
2A
104 mΩ
Taiyo-Yuden
2 mm × 1.6 mm × 1 mm
1.9 A
115 mΩ
TDK
2 mm × 1.6 mm × 1 mm
1.4 A
151 mΩ
Murata
2 mm × 1.25 mm × 1 mm
1.2 A
110 mΩ
8.2.2.1.2 Capacitor Selection
The LM3263 is designed to use ceramic capacitors for its input and output filters. Use a 10-µF capacitor for the
input and approximately 10 µF actual total output capacitance. Capacitor types such as X5R, X7R are
recommended for both filters. These provide an optimal balance between small size, cost, reliability, and
performance for cell phones and similar applications. Table 4 lists suggested part numbers and suppliers. DC
bias characteristics of the capacitors must be considered while selecting the voltage rating and case size of the
capacitor. Smaller case sizes for the output capacitor mitigate piezo-electric vibrations of the capacitor when the
output voltage is stepped up and down at fast rates. However, they have a bigger percentage drop in value with
dc bias. For even smaller total solution size, 0402 (1005) case size capacitors are recommended for filtering. Use
of multiple 2.2-µF or 1-µF capacitors can also be considered. For RF PA applications, split the output capacitor
between DC-DC converter and RF PAs; TI recomments 10 µF (COUT1) + 4.7 µF (COUT2) + 3 × 1 µF
(COUT3)(assuming one 2G PA and three 3G/4G PAs — COUT2 is for 2G PA, and COUT3 is for 3G/4G PA). The
optimum capacitance split is application dependent, and for stability the actual total capacitance (taking into
account effects of capacitor DC bias, temperature de-rating, aging and other capacitor tolerances) must target 10
µF with 2.5-V DC bias (measured at 0.5 VRMS). Place all the output capacitors very close to the respective
device. TI highly recommends placing a high-frequency capacitor (3300 pF) next to COUT1.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
25
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Table 4. Suggested Capacitors And Their Suppliers
CAPACITANCE
MODEL
SIZE (W × L)
VENDOR
10 µF
GRM185R60J106M
1.6 mm × 0.8 mm
Murata
10 µF
CL05A106MP5NUN
1 mm × 0.5 mm
Samsung
4.7 µF
CL05A475MP5NRN
1 mm × 0.5 mm
Samsung
1 µF
CL03A105MP3CSN
0.6 mm × 0.3 mm
Samsung
1 µF
C0603X5R0J105M
0.6 mm × 0.3 mm
TDK
3300 pF
GRM022R60J332K
0.4 mm × 0.2 mm
Murata
8.2.3 Application Curves
SW
2V/DIV
SW
2V/DIV
VOUT
1V/DIV
VOUT
1V/DIV
2V/DIV SDATA
2V/DIV
SDATA
10 s/DIV
10µs/DIV
VBATT = 4.2 V
VOUT = 3.4 V
No load
VBATT = 4.2 V
Figure 28. Start-up From Low-Power Mode
VOUT = 3.4 V
No load
Figure 29. Start-Up From Standby Mode
9 Power Supply Recommendations
The LM3263 device is designed to operate from an input voltage supply range from 2.7 V to 5.5 V. This input
supply should be well-regulated and able to withstand maximum input current and maintain stable voltage
without voltage drop even under largest load transition conditions.
26
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
10 Layout Considerations
10.1 Layout Guidelines
10.1.1 1. Overview
PC board layout is critical to successfully designing a DC-DC converter into a product. A properly planned board
layout optimizes the performance of a DC-DC converter and minimizes effects on surrounding circuitry while also
addressing manufacturing issues that can have adverse impacts on board quality and final product yield.
10.1.2 2. PCB
Poor board layout can disrupt the performance of a DC-DC converter and surrounding circuitry by contributing to
EMI, ground bounce, and resistive voltage loss in the traces. Erroneous signals could be sent to the DC-DC
converter device, resulting in poor regulation or instability. Poor layout can also result in re-flow problems leading
to poor solder joints between the DSBGA package and board pads. Poor solder joints can result in erratic or
degraded performance of the converter.
10.1.2.1 Energy Efficiency
Minimize resistive losses by using wide traces between the power components and doubling up traces on
multiple layers when possible.
10.1.2.2 EMI
By its very nature, any switching converter generates electrical noise. The circuit board designer’s challenge is to
minimize, contain, or attenuate such switcher-generated noise. A high-frequency switching converter, such as the
LM3263, switches Ampere level currents within nanoseconds, and the traces interconnecting the associated
components can act as radiating antennas. The following guidelines are offered to help to ensure that EMI is
maintained within tolerable levels.
To help minimize radiated noise:
• Place the LM3263 DC-DC converter, its input capacitor, and output filter inductor and capacitor close
together, and make the interconnecting traces as short as possible.
• Arrange the components so that the switching current loops curl in the same direction. During the first half of
each cycle, current flows from the input filter capacitor, through the internal PFET of the LM3263 and the
inductor, to the output filter capacitor, then back through ground, forming a current loop. In the second half of
each cycle, current is pulled up from ground, through the internal synchronous NFET of the LM3263 by the
inductor, to the output filter capacitor and then back through ground, forming a second current loop. Routing
these loops so the current curls in the same direction prevents magnetic field reversal between the two halfcycles and reduces radiated noise.
• Make the current loop area(s) as small as possible. Interleave doubled traces with ground planes or return
paths, where possible, to further minimize trace inductances.
• The Active Current Assist and Bypass (ACB) trace must be kept short and routed directly from ACB pads to
the VOUT pad at the inductor.
To help minimize conducted noise in the ground-plane:
• Reduce the amount of switching current that circulates through the ground plane — connect PGND bump of
the LM3263 and its input filter capacitor together using generous component-side copper fill as a pseudoground plane. Then connect this copper fill to the system ground-plane (if one is used) by multiple vias
located at the input filter capacitor ground terminal. The multiple vias help to minimize ground bounce at the
LM3263 by giving it a low-impedance ground connection. Do not route the PGND pad directly to the RF
ground plane.
• An additional high frequency capacitor in 01005 (0402 mm) case size is also recommended between PVIN
and the RF ground plane. Do not connect to PGND directly.
• For optimum RF performance connect the output capacitor ground to the RF ground or system ground plane.
Do not connect to PGND directly.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
27
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
Layout Guidelines (continued)
To help minimize coupling to the voltage feedback trace of the DC-DC converter:
• Route noise sensitive traces, such as the voltage feedback path (FB), as directly as possible from the DC-DC
converter FB pad to the VOUT pad of the output capacitor, but keep them away from noisy traces between
the power components.
To
•
•
•
•
•
help minimize noise coupled back into power supplies:
Use a star connection to route from the VBATT power input to DC-DC converter PVIN and to VBATT_PA.
Route traces for minimum inductance between PVIN pads and the input capacitor(s).
Route traces to minimize inductance between the input capacitors and the ground plane.
Maximize power supply trace inductance(s) to reduce coupling among function blocks.
Inserting a ferrite bead in line with power supply traces can offer a favorable tradeoff in terms of board area,
by attenuating noise that might otherwise propagate through the supply connections, allowing the use of
fewer bypass capacitors.
10.1.3 3. Manufacturing Considerations
The LM3263 device is packaged in a 16-pin (4 × 4) array of 0.24-mm solder balls, with a 0.4-mm pad pitch. A
few simple design rules go a long way to ensuring a good layout.
• Pad size must be 0.225 ± 0.02 mm. Solder mask opening must be 0.325 ± 0.02 mm.
• As a thermal relief, connect to each pad with 9-mil wide, 6-mil long traces and incrementally increase each
trace to its optimal width. Symmetry is important to ensure the solder bumps re-flow evenly. Refer toAN-1112
DSBGA Wafer Level Chip Scale Package (SNVA009).
10.2 4. Layout Examples
VBATT
2.7 V to 5.5 V
0.1 µF
10 µF
PVIN
PACB
SVDD
FB
VIO
1.8 V
RFFE
Master
ACB
Output Voltage
0.4 V to 3.6 V
1.5 µH
SCLK
SW
LM3263
SDATA
10 µF
3.3 nF
4.7 µF
VBATT_PA
GPO1
BGND
SGND
MMMB
VCC_PA
PGND
1 µF
3G/4G
VCC_PA
PA
PA
Copyright © 2016, Texas Instruments Incorporated
Figure 30. Simplified LM3263 RF Evaluation Board Schematic
28
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
4. Layout Examples (continued)
LM3263 DC-DC Converter
3G/4G PA
Multi-Mode Multi-Band PA
Figure 31. Top View of RF Evaluation Board With PAs
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
29
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
4. Layout Examples (continued)
10.2.1 DC-DC Converter
VBATT Input
from board edge
RF bypass to
RF GND Plane
Inductor
Input Cap
(RF)
Output Cap
(RF)
RF bypass to
RF GND Plane
Output Cap
(Main)
Input Cap
(Main)
LM3263
Inductance
Minimized
Input Cap ground side is connected to
PGND pin. PGND island should be isolated
on the top layer andconnected to system
ground plane directly with multi vias.
Figure 32. Top Layer
30
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
4. Layout Examples (continued)
Inductor
Input Cap
(RF)
Output Cap
(RF)
Output Cap
(Main)
PVIN can be connected to CIN
with multi-vias if Power plane is in
an innner plane.
LM3263
FB trace
(low current)
Input Cap
(Main)
S VDD
Connection
to CIN
PACB
Connection
to CIN
Figure 33. Board Layer 2 – FB, SVDD, PACB, PVIN
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
31
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
4. Layout Examples (continued)
Control Traces Routed
Away From PowerTraces
Same net, but should be
kept isolated on this layer
Inductor
Input Cap
(RF)
Output Cap
(RF)
Output Cap
(Main)
SW : Short,
20 mil min width
LM3263
ACB : 20 mil min width.
ACB trace can be placedin
other layer if more layers
are available.
Input Cap
(Main)
Figure 34. Board Layer 3 – SW, ACB
32
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
4. Layout Examples (continued)
VCC_PA:
Connects Directly To
Cout at This Point
Input Cap
(RF)
Inductor
Output Cap
(RF)
Output Cap
(Main)
Input Cap
(Main)
LM3263
VCC_PA:
Wide, High-Current Trace
Figure 35. Board Layer 4 – VCC_PA, System GND Plane
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
33
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
4. Layout Examples (continued)
VBATT:
Wide, High -Current
Trace
Inductor
Input Cap
(RF)
Output Cap
(RF)
Output Cap
(Main)
Input Cap
(Main)
LM3263
Figure 36. Board Layer 5 – VBATT Connection
34
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
4. Layout Examples (continued)
VBATT Star
Connection
VBATT Connection for
DC -DC Converter
VBATT BUS
Connection for PA(s)
Figure 37. Multiple Board Layers – VBATT Supply Star Connection
10.2.1.1 Star Connection Between VBATT, DC-DC Converter, and PA
10.2.1.1.1 VBATT Star Connection
It is critically important to use a star connection from VBATT supply to the LM3263 PVIN and from VBATT to PA
modules as implementing a daisy-chain supply connection may add noise to the PA output.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
35
LM3263
SNVS837B – JUNE 2013 – REVISED APRIL 2016
www.ti.com
4. Layout Examples (continued)
Star Connection at VBATT
VBATT_PA
VIN DC-DC
VBATT_PA
*
*
VIN
VBATT
PA
PA
+
LM3263
_
* Proper decoupling on VBATT_PA is strongly recommended.
Copyright © 2016, Texas Instruments Incorporated
Figure 38. VBATT Star Connection on PCIN and VBATT_PA
10.3 DSBGA Package Assembly and Use
Use of the DSBGA package requires specialized board layout, precision mounting, and careful re-flow
techniques, as detailed in AN-1112 DSBGA Wafer Level Chip Scale Package (SNVA009). Refer to the section
Surface Mount Technology (SMD) Assembly Considerations. For best results in assembly, alignment ordinals on
the PC board must be used to facilitate placement of the device. The pad style used with DSBGA package must
be the NSMD (non-solder mask defined) type. This means that the solder-mask opening is larger than the pad
size. This prevents a lip that otherwise forms if the solder-mask and pad overlap from holding the device off the
surface of the board and interfering with mounting. See SNVA009 for specific instructions how to do this.
The 16-pin package used for the LM3263 has 265 micron (nominal) solder balls and requires 0.225-mm pads for
mounting the circuit board. The trace to each pad must enter the pad with a 90° entry angle to prevent debris
from being caught in deep corners. Initially, the trace to each pad must be about 0.142-mm wide, for a section
approximately 0.127-mm long, as a thermal relief. Then each trace must neck up or down to its optimal width.
An important criterion is symmetry to insure the solder bumps on the LM3263 re-flow evenly and that the device
solders level to the board. In particular, special attention must be paid to the pads for bumps A1, A3, B1, and B3
because PGND, PVIN and BGND are typically connected to large copper planes; inadequate thermal relief can
result in inadequate re-flow of these bumps.
The DSBGA package is optimized for the smallest possible size in applications with red-opaque or infraredopaque cases. Because the DSBGA package lacks the plastic encapsulation characteristic of larger devices, it is
vulnerable to light. Backside metallization and/or epoxy coating, along with front-side shading by the printed
circuit board, reduce this sensitivity. However, the package has exposed die edges that are sensitive to light in
the red and infrared range shining on the exposed die edges of the package.
36
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
LM3263
www.ti.com
SNVS837B – JUNE 2013 – REVISED APRIL 2016
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Documentation Support
11.2.1 Related Documentation
For additional information, see the following:
AN-1112 DSBGA Wafer Level Chip Scale Package (SNVA009)
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
MIPI is a registered trademark of Mobile Industry Processor Interface Alliance.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2013–2016, Texas Instruments Incorporated
Product Folder Links: LM3263
37
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM3263TME/NOPB
ACTIVE
DSBGA
YFQ
16
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-30 to 90
S61
LM3263TMX/NOPB
ACTIVE
DSBGA
YFQ
16
3000
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-30 to 90
S61
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of