LM3445-EDSNEV/NOPB

User's Guide SNVA442C – June 2010 – Revised May 2013 AN-2061 LM3445 A19 Edison Retrofit Evaluation Board 1 Introduction The evaluation board included in this shipment converts 85VAC to 135VAC input and drives five to thirteen series connected LED’s at the currents listed in the Evaluation Board Operating Conditions section. This is a two-layer board using the bottom and top layer for component placement. The board is surrounded by a larger area allowing for extra test points and connectors for ease of evaluation. The actual board size is contained inside the larger outer area and can be cut out for the smallest size possible. The evaluation board can be modified to adjust the LED forward current and the number of series connected LEDs. The topology used for this evaluation board eliminates the need for passive power factor correction and results in high efficiency and power factor with minimal component count which results in a size that can fit in a standard A19 Edison socket. This board also operates correctly and dims smoothly using most standard triac dimmers. Output current is regulated within ±15% of nominal from circuit to circuit and over line voltage variation. For details on the LM3445 IC, see the LM3445 Triac Dimmable Offline LED Driver Data Sheet (SNVS570). A bill of materials shown in Table 2 describes the parts used on this demonstration board. A schematic and layout have also been included along with measured performance characteristics including EMI/EMC data. The above restrictions for the input voltage are valid only for the demonstration board as shipped with the schematic below. for detailed information regarding the LM3445 device, see the LM3445 Triac Dimmable Offline LED Driver Data Sheet (SNVS570). The board is currently set up to drive five to thirteen series connected LEDs, but the evaluation board may be modified to accept more series LEDs. Refer to the tables in this document to modify the board to accept more LEDs and/or adjust for different current levels. 2 Evalution Board Operating Conditions VIN = 85VAC to 135VAC 5 • • • • • • to 13 series connected LEDs as configured with the currents listed below: Can drive up to 18 series LEDs (see table) ILED = 340 mA (5 LEDs) ILED = 300 mA (7 LEDs) ILED = 260 mA (9 LEDs) ILED = 230 mA (11 LEDs) ILED = 205 mA (13 LEDs) All trademarks are the property of their respective owners. SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated 1 Simplified LM3445 Schematic 3 www.ti.com Simplified LM3445 Schematic V+ V+ R2 D1 R1 C1 D2 R7 R4 C10 R3 Q1 C5 VLED+ D8 R22 D7 C6 R8 R6 L1 VCC R24 L2 + C4 D4 C3 VLED± L3 C2 R9 C8 1 RT1 C9 ASNS 2 FLTR1 R5 VCC 9 GATE 8 R16 F1 C13 3 DIM LINE VCC BLDR 10 NEUTRAL LINE EMI FILTER COFF 4 COFF ISNS 7 5 FLTR2 GND 6 FLTR2 C14 R15 C15 Q4 R12 DIM COFF R14 C12 LM3445 COFF Current Source WARNING The LM3445 evaluation boards have no isolation or any type of protection from shock. Caution must be taken when handling evaluation board. Avoid touching evaluation board, and removing any cables while evaluation board is operating. Isolating the evaluation board rather than the oscilloscope is highly recommended. WARNING This LM3445 evaluation PCB is a non-isolated design. The ground connection on the evaluation board is NOT referenced to earth ground. If an oscilloscope ground lead is connected to the evaluation board ground test point for analysis, and AC power is applied, the fuse (F1) will fail open. The oscilloscope should be powered via an isolation transformer before an oscilloscope ground lead is connected to the evaluation board. 2 AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback Pin-Out www.ti.com 4 Pin-Out ASNS 1 10 BLDR FLTR1 2 9 VCC DIM 3 8 GATE COFF 4 7 ISNS FLTR2 5 6 GND Figure 1. 10-Pin VSSOP Table 1. Pin Description 10 Pin VSSOP Pin No Name Description 1 ASNS PWM output of the triac dim decoder circuit. Outputs a 0 to 4V PWM signal with a duty cycle proportional to the triac dimmer on-time. 2 FLTR1 First filter input. The 120Hz PWM signal from ASNS is filtered to a DC signal and compared to a 1 to 3V, 5.85 kHz ramp to generate a higher frequency PWM signal with a duty cycle proportional to the triac dimmer firing angle. Pull above 4.9V (typical) to tri-state DIM. 3 DIM 4 COFF OFF time setting pin. A user set current and capacitor connected from the output to this pin sets the constant OFF time of the switching controller. 5 FLTR2 Second filter input. A capacitor tied to this pin filters the PWM dimming signal to supply a DC voltage to control the LED current. Could also be used as an analog dimming input. 6 GND Circuit ground connection. 7 ISNS LED current sense pin. Connect a resistor from main switching MOSFET source, ISNS to GND to set the maximum LED current. 8 GATE Power MOSFET driver pin. This output provides the gate drive for the power switching MOSFET of the buck controller. 9 VCC 10 BLDR Input/output dual function dim pin. This pin can be driven with an external PWM signal to dim the LEDs. It may also be used as an output signal and connected to the DIM pin of other LM3445 or LED drivers to dim multiple LED circuits simultaneously. Input voltage pin. This pin provides the power for the internal control circuitry and gate driver. Bleeder pin. Provides the input signal to the angle detect circuitry as well as a current path through a switched 230Ω resistor to ensure proper firing of the triac dimmer. SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated 3 LM3445 Evaluation Board Schematic www.ti.com 5 LM3445 Evaluation Board Schematic 4 AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback Bill of Materials (BOM) LM3445 Evaluation Board www.ti.com 6 Bill of Materials (BOM) LM3445 Evaluation Board Table 2. Bill of Materials (BOM) REF DES Description MFG U1 IC DRIVER LED W/TRIAC DIM 10VSSOP Texas Instruments LM3445 C1, C10 Ceramic, 47000pF, 500V, X7R, 1210 Johanson Dielectrics 501S41W473KV4E C2 CAP FILM MKP .0047µF 310VAC X2 Vishay/BC Components BFC233820472 C3 CAP 470µF 50V ELECT PW RADIAL Nichicon UPW1H471MHD C4532X7R2E334K C4/RBLDR (1) (1) MFG Part Number DNP C5 Ceramic, .33µF, 250V, X7R, 1812 TDK Corporation C6 CAP .10µF 305VAC EMI SUPPRESSION EPCOS B32921C3104M C8 Ceramic, 47µF, X5R, 16V, 1210 MuRata GRM32ER61C476ME15L C9 Ceramic, .1µF, 250V, X7R, 1210 Taiyo Yuden QMK325B7104KN-T C12 Ceramic, 470pF, 50V, X7R, 0603 MuRata GRM188R71H471KA01D C13, C15 Ceramic, 0.1µF, 16V, X7R, 0603 MuRata GRM188R71C104KA01D C14 Ceramic, 0.47µF, 16V, X7R, 0603 MuRata GRM188R71C474KA88D D1 DIODE SCHOTTKY 1A 200V PWRDI 123 Diodes Inc. DFLS1200-7 D2 Bridge Rectifier, Vr = 400V, Io = 0.8A, Vf = 1V Diodes Inc. HD04-T D4 DIODE FAST 1A 300V SMA Fairchild Semi conductor ES1F D7 DIODE ZENER 15V 500MW SOD-123 Fairchild Semi conductor MMSZ5245B D8 DIODE SCHOTTKY 1A 200V PWRDI 123 Diodes Inc. DFLS1200-7 F1 FUSE 1A 125V FAST Cooper/Bussman 6125FA1A J5, J10 CONN HEADER .312 VERT 2POS TIN Tyco Electronics 1-1318301-2 L1, L2 INDUCTOR 3900µH .12A RADIAL J.W. Miller/Bourns RL875S-392K-RC L3 820µH, Shielded Drum Core Coilcraft Inc. MSS1038-824KL M1 JUMPER WIRE 0.3" J6 TO J1 3M 923345-03-C M2 JUMPER WIRE 0.3" J7 to J4 3M 923345-03-C M3 JUMPER WIRE 0.3" J2 TO J8 3M 923345-03-C M4 JUMPER WIRE 0.3" J3 TO J9 3M 923345-03-C Q1 MOSFET N-CH 240V 260MA SOT-89 Infineon Technologies BSS87 L6327 Q2 MOSFET N-CH 250V 4.4A DPAK Fairchild Semi conductor FDD6N25TM R1, R3 RES 200kΩ, 0.25W, 1%, 1206 Vishay-Dale CRCW1206200kFKEA R2, R7 RES 274kΩ, 0.25W, 1%, 1206 Vishay-Dale CRCW1206274kFKEA R4 RES 430Ω, 1/2W, 5%, 2010 Vishay-Dale CRCW2010430RJNEF R5 RES 430Ω, 1/3W, 5%, 1210 Vishay-Dale CRCW1210430RJNEA R6, R24 RES 30.1kΩ, 0.25W, 1%, 1206 Vishay-Dale CRCW120630k1FKEA R8 RES 49.9kΩ, 0.1W, 1%, 0603 Vishay-Dale CRCW060349K9FKEA R9 RES 48.7kΩ, 0.1W, 1%, 0603 Vishay-Dale CRCW060348K7FKEA R10 DNP R12 RES 4.7Ω, 0.1W, 5%, 0603 Vishay-Dale CRCW06034R70JNEA R14 RES 1.54Ω, 1/4W, 1%, 1206 Vishay-Dale CRCW12061R54FNEA R15 RES 3.16kΩ, 0.1w, 1%, 0603 Vishay-Dale CRCW06033K16FKEA R16 RES 255kΩ, 0.1W, 1%, 0603 Vishay-Dale CRCW0603255KFKEA R22 RES 40.2Ω, 0.125W, 1%, 0805 Vishay-Dale CRCW080540R2FKEA RT1 CURRENT LIMITOR INRUSH 60Ω 20% Cantherm MF72-060D5 TP1, TP2, TP3, TP4 Terminal, Turret, TH, Double Keystone Electronics 1502-2 C4/RBLDR is a dual purpose pad which is unpopulated by default. A ceramic capacitor (C4) may be used here if extra high frequency bypassing is desired across the LED load. Alternatively a bleeder resistor (RBLDR) in the range of 10kΩ to 100kΩ may be placed here to quickly discharge C3 and prevent prolonged LED glow due to the energy stored in C3. SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated 5 Output Current versus Number of LEDs for Various Modifications 7 Output Current versus Number of LEDs for Various Modifications # of LEDs (1) (2) (3) (4) 6 www.ti.com Output Current (mA) Original Circuit Output Current (mA) Modification A (1) Output Current (mA) Modification B (2) Output Current (mA) Modification C (3) 2 520 3 500 4 475 5 340 248 265 455 6 315 235 250 432 7 300 222 237 412 8 275 210 224 9 260 200 212 10 245 190 200 11 230 180 190 12 215 170 180 13 205 164 170 14 (4) 196 156 162 15 (4) 190 150 155 16 (4) 183 142 148 17 (4) 175 135 142 18 (4) 170 130 137 Modification A: R14 = 2.37Ω, R16 = 150kΩ, C3 = 330µF, 63V. Modification B: R14 = 2.2Ω, R16 = 165kΩ. Modification C: R14 = 1.2Ω, R16 = 137kΩ, L3 = 470µH, C3 = 1000µF, 25V. For all applications using greater than 13 LEDs a 330µF, 63V output capacitor (C3) was used. AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback Typical Performance Characteristics www.ti.com 8 Typical Performance Characteristics 90 0.95 9 LEDs @ 260 mA 9 LEDs @ 260 mA 0.90 POWER FACTOR EFFICIENCY (%) 85 80 75 0.85 0.80 70 80 90 100 110 120 130 0.75 80 140 90 110 120 130 140 LINE VOLTAGE (VAC) LINE VOLTAGE (VAC) Figure 2. Efficiency vs. Line Voltage Original Circuit Figure 3. Power Factor vs. Line Voltage Original Circuit 0.95 90 18 LEDs @ 130 mA 18 LEDs @ 130 mA 0.90 POWER FACTOR 85 EFFICIENCY (%) 100 80 0.85 0.80 75 70 80 0.75 80 90 100 110 120 130 90 100 110 120 130 140 140 LINE VOLTAGE (VAC) LINE VOLTAGE (VAC) Figure 4. Efficiency vs. Line Voltage Modification A SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback Figure 5. Power Factor vs. Line Voltage Modification A AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated 7 Typical Performance Characteristics www.ti.com 90 0.95 13 LEDs @ 170 mA 13 LEDs @ 170 mA 0.90 POWER FACTOR EFFICIENCY (%) 85 80 75 0.85 0.80 70 80 90 100 110 120 130 140 0.75 80 90 LINE VOLTAGE (VAC) Figure 6. Efficiency vs. Line Voltage Modification B 8 100 110 120 130 140 LINE VOLTAGE (VAC) Figure 7. Power Factor vs. Line Voltage Modification B AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback PCB Layout www.ti.com 9 PCB Layout Figure 8. Top Layer Figure 9. Bottom Layer WARNING The LM3445 evaluation boards have no isolation or any type of protection from shock. Caution must be taken when handling evaluation board. Avoid touching evaluation board, and removing any cables while evaluation board is operating. Isolating the evaluation board rather than the oscilloscope is highly recommended. SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated 9 EMI/EMC Information 10 www.ti.com EMI/EMC Information Figure 10. Radiated EMI Figure 11. Conducted EMC. Line = Blue, Neutral = Black 10 Frequency Quasi-Peak Amplitude Quasi-Peak Limit Quasi-Peak Delta Average Amplitude Average Limit Neutral 154 kHz 57 66 -9 47 56 -9 Line 1.1 MHz 31 46 -15 AN-2061 LM3445 A19 Edison Retrofit Evaluation Board Copyright © 2010–2013, Texas Instruments Incorporated Average Delta SNVA442C – June 2010 – Revised May 2013 Submit Documentation Feedback IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated