User's Guide
SLUUBA8 – May 2015
120 VAC Valley Fill Buck Triac Dimmable LED Driver
This user's guide describes the characteristics, use, performance data and typical characteristic curves of
the LM3445 valley fill evaluation module. This evaluation module (EVM) implements a dimming solution
using the LM3445 integrated circuit from TI. A complete circuit description, schematic diagram, printedcircuit-board (PCB) layout, and bill of materials (BOM) are also included.
1
2
3
4
5
6
7
Contents
Introduction ................................................................................................................... 2
Description .................................................................................................................... 2
2.1
Typical Applications ................................................................................................ 2
2.2
LM3445 Features ................................................................................................... 2
Electrical Performance Specifications ..................................................................................... 3
Schematic ..................................................................................................................... 4
4.1
Suggested Dimming Connection (Remove Dimmer for Non-Dimming!)..................................... 5
Performance Data and Typical Characteristic Curves .................................................................. 6
5.1
Power Factor ........................................................................................................ 6
5.2
Line Regulation ..................................................................................................... 6
5.3
Load Regulation..................................................................................................... 7
5.4
Efficiency ............................................................................................................. 7
5.5
Input Current ........................................................................................................ 8
5.6
Output Current ...................................................................................................... 8
5.7
Turn On Waveform ................................................................................................. 9
5.8
Turn Off Waveform ................................................................................................. 9
5.9
Dimming – Lutron DVELV-303P Dimmer ...................................................................... 10
5.10 Dimming – Lutron DVLV-6006 Dimmer ........................................................................ 10
5.11 EMI Scan – 6 LEDs ............................................................................................... 11
5.12 Dimmer Testing .................................................................................................... 11
PCB Layout ................................................................................................................. 12
Bill of Materials ............................................................................................................. 13
List of Figures
1
LM3445EVM-695 Schematic ............................................................................................... 4
2
Suggested Dimming Connection
3
4
5
6
7
8
9
10
11
12
13
14
.......................................................................................... 5
LM3445EVM-695 Power Factor ........................................................................................... 6
LM3445EVM-695 Line Regulation ......................................................................................... 6
LM3445EVM-695 Load Regulation ........................................................................................ 7
LM3445EVM-695 Efficiency ................................................................................................ 7
LM3445EVM-695 Off-Line Valley Fill Buck EVM Input Current ....................................................... 8
LM3445EVM-695 Off-Line Valley Fill Buck EVM Output Current ..................................................... 8
LM3445EVM-695 Off-Line Valley Fill Buck EVM Start-Up ............................................................. 9
LM3445EVM-695 Off-Line Valley Fill Buck EVM Turn Off ............................................................. 9
Lutron Trailing Edge DVELV-303P, Output = 150 mA, VLED = 22 V ................................................. 10
Lutron Leading Edge DVLV-6006, Output = 20 mA, VLED = 22 V .................................................... 10
EMI Scan .................................................................................................................... 11
LM3445EVM-695 Top Layer Assembly Drawing (Top View) ......................................................... 12
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
1
Introduction
15
www.ti.com
LM3445EVM-695 Bottom Assembly Drawing (Bottom View)
........................................................
12
List of Tables
1
1
LM3445EVM-695 Electrical Performance Specifications ............................................................... 3
2
Dimmer Testing ............................................................................................................. 11
3
LM3445EVM-695 Bill of Materials........................................................................................ 13
Introduction
The LM3445 Valley Fill EVM is a 120-VAC non-isolated dimmable LED driver whose form factor is intended
for A-15, A-19, A-21, A-23, R-20, R-25, R-27, R-30, R-40, PS-25, PS-30, PS-35, BR-30, BR-38, BR-40,
PAR-20, PAR-30, PAR-30L, G-25, G-30, G-40, and other LED bulbs.
2
Description
The LM3445 Valley Fill EVM implements a dimming solution using the LM3445 integrated circuit from TI.
The LM3445 is an adaptive constant off-time AC/DC buck constant current controller with built-in phasedimming decoder. Line cycles are analyzed continuously by an internal low-power digital controller for
shape and symmetry. An analog current reference is then generated and used by the power converter
stage to regulate the output current. The analog reference is manipulated using control algorithms
developed to optimize dimmer compatibility, power factor, and THD. Using constant off-time control, the
solution achieves low part count, high efficiency, and inherently provides variation in the switching
frequency. This variation creates an emulated spread spectrum effect easing the converters' EMI
signature and allowing a smaller input filter.
2.1
Typical Applications
Triac compatible LED lighting, including forward- and reverse-phase compatibility.
2.2
LM3445 Features
•
•
•
•
•
•
•
•
•
•
2
Triac dim decoder circuit for LED dimming
Integrated phase-angle decoder
Adjustable switching frequency
Low quiescent current
Adaptive programmable off-time allows for constant ripple current
Leading- and trailing-edge dimmer compatibility
Dimming implemented via an analog reference
Smooth dimming transitions
Low BOM cost and small PCB footprint
Low profile 10-pin MSOP Package or 14-pin SOIC
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
SLUUBA8 – May 2015
Submit Documentation Feedback
Electrical Performance Specifications
www.ti.com
3
Electrical Performance Specifications
Table 1 lists the LM3445EVM-695 electrical performance specifications.
Table 1. LM3445EVM-695 Electrical Performance Specifications
Parameter
Test Conditions
MIN
TYP
90
120
MAX
UNITS
Input Characteristics
Voltage range
Maximum input
current
135
V
0.150
A
530
mA
Output Characteristics
Output current
Output voltage = 20 V
Output current
regulation
Line regulation: Input voltage = 90 to 135
470
±1
Load regulation: 15-V to 25-V change
±1
%
80
mApp
100
kHz
LED Ripple
500
%
Systems Characteristics
Switching
frequency
Power efficiency
120-V, 60-Hz input, 20-V LED stack
82
Operating
temperature
SLUUBA8 – May 2015
Submit Documentation Feedback
25
%
125
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
ºC
3
Schematic
4
www.ti.com
Schematic
Figure 1 illustrates the LM3445EVM-695 schematic.
TP2
R17
22
2W
AC INPUT
90VAC - 135VAC
135mA MAX.
LED+
1mH
0.27A
L2
R3
332k
3.9mH
0.18A
R1
866
1W
J1
TP4
L1
D2
V+
LINE
RV1
C4
0.01µF
C6
22µF
C12
0.1µF
D7
R12
1.00Meg
C13
1µF
R14
499k
D6
C5
0.022µF
VF
D8
Q5
Q1
C1
0.22µF
D1
15V
+
R13
1.00Meg
C10
22µF
D5
~
DANGER HIGH VOLTAGE
TP3
NEUTRAL
~
J2
DC OUTPUT
24VDC MAX.
470mA - 530mA
-
BR1
R11
200k
R10
R5
49.9k
124
V+
L3
VCC
C3
1000pF
Q8
1mH
0.6A
Q4
LEDTP5
2
R4
100k
Q2
C9
R23
150
R6
100k
4.7µF
R8
10.0k
3
1
D4
C2
0.01µF
R7
7.50k
R9
100
Q3
D9
R18
301
D3
BLDR
R2
2.2M
R16
VCC
LM3445MM/NOPB
R15
1
280k
Q6
2
49.9k
3
C16
0.22µF
5
R19
36.5
C14
0.47µF
6
C15
0.1µF
ASNS
BLDR
FLTR1
VCC
DIM
GATE
FLTR2
ISNS
GND
COFF
10
9
C7
22µF
C8
0.1µF
R20
Q7
100
8
7
4
U1
R21
1.2
0.25W
R22
C11
330pF
TP1
Figure 1. LM3445EVM-695 Schematic
4
120 VAC Valley Fill Buck Triac Dimmable LED Driver
SLUUBA8 – May 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Schematic
www.ti.com
4.1
Suggested Dimming Connection (Remove Dimmer for Non-Dimming!)
Figure 2 displays a dimming connection scenario.
Triac Dimmer
LM3445-120VSMEVM
L
LEDí
AC Source
N
J1
LED+
LED Load
AMP
Meter
Figure 2. Suggested Dimming Connection
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
5
Performance Data and Typical Characteristic Curves
5
www.ti.com
Performance Data and Typical Characteristic Curves
(Unless otherwise stated, the input voltage is 120 V, 60 Hz and the LED stack voltage is 22 V.)
5.1
Power Factor
The LM3445EVM-695 power factor is displayed in Figure 3.
1
0.975
Power Factor
0.95
0.925
0.9
0.875
0.85
0.825
0.8
90
95
100
105
110
115
Input Voltage (VAC)
120
125
130
135
D001
Figure 3. LM3445EVM-695 Power Factor
5.2
Line Regulation
Figure 4 illustrates the LM3445EVM-695 line regulation.
600
580
560
LED Current (mA)
540
520
500
480
460
440
420
400
90
95
100
105
110
115
LED Voltage (V)
120
125
130
135
D002
Figure 4. LM3445EVM-695 Line Regulation
6
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
SLUUBA8 – May 2015
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
5.3
Load Regulation
Figure 5 contains the LM3445EVM-695 load regulation data.
600
580
560
LED Current (mA)
540
520
500
480
460
440
420
400
15
16
17
18
19
20
Input Voltage (V)
21
22
23
24
25
D003
Figure 5. LM3445EVM-695 Load Regulation
5.4
Efficiency
Figure 6 illustrates the LM3445EVM-695 efficiency for 5, 6, and 7 LEDs.
85
84
83
Efficiency (%)
82
81
80
79
78
77
5 LEDs
6 LEDs
7 LEDs
76
75
90
95
100
105
110
115
Input Voltage (V AC)
120
125
130
135
D004
Figure 6. LM3445EVM-695 Efficiency
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
7
Performance Data and Typical Characteristic Curves
5.5
www.ti.com
Input Current
Figure 7 displays the LM3445EVM-695 off-line valley fill Buck EVM input current.
Figure 7. LM3445EVM-695 Off-Line Valley Fill Buck EVM Input Current
5.6
Output Current
Figure 8 displays the LM3445EVM-695 off-line valley fill Buck EVM output current.
Figure 8. LM3445EVM-695 Off-Line Valley Fill Buck EVM Output Current
8
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
SLUUBA8 – May 2015
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
5.7
Turn On Waveform
The LM3445EVM-695 off-line valley fill Buck EVM start-up is displayed in Figure 9.
Figure 9. LM3445EVM-695 Off-Line Valley Fill Buck EVM Start-Up
5.8
Turn Off Waveform
Figure 10 displays the LM3445EVM-695 off-line valley fill Buck EVM turn off.
Figure 10. LM3445EVM-695 Off-Line Valley Fill Buck EVM Turn Off
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
9
Performance Data and Typical Characteristic Curves
5.9
www.ti.com
Dimming – Lutron DVELV-303P Dimmer
Figure 11 illustrates the Lutron trailing edge DVELV-303P, output = 150 mA, VLED = 22 V.
Figure 11. Lutron Trailing Edge DVELV-303P, Output = 150 mA, VLED = 22 V
5.10 Dimming – Lutron DVLV-6006 Dimmer
Figure 12 displays the Lutron leading edge DVLV-6006, output = 20 mA, VLED = 22 V.
Figure 12. Lutron Leading Edge DVLV-6006, Output = 20 mA, VLED = 22 V
10
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
SLUUBA8 – May 2015
Submit Documentation Feedback
Performance Data and Typical Characteristic Curves
www.ti.com
5.11 EMI Scan – 6 LEDs
Figure 13 illustrates the EMI scan data.
Figure 13. EMI Scan
5.12 Dimmer Testing
Table 2 lists the dimmer testing results.
Table 2. Dimmer Testing
Make
Model
Flicker-Free
Lutron
DVELV-303P
Y
Lutron
DVLV-6006
Y
Lutron
MACL-153M
Y
Lutron
D-600P
Y
Lutron
SCL153P
Y
Leviton
IP106-1LZ
Y
Lutron
DVNCL-153PLH
Y
Lutron
AY-600P
Y
Lutron
NTLV-600
Y
Lutron
TG-600PH
Y
Lutron
S-600P
Y
Lutron
DV600P-IV
Y
Lutron
DVPDC-203P-IV
Y
Lutron
6684
Y
Lutron
NLV-600-IV
Y
Lutron
Q600P
Y
Lutron
SLV-600P
Y
Lutron
AYCL-153P
Y
Lutron
VZM10-1LZ
Y
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
11
PCB Layout
6
www.ti.com
PCB Layout
Figure 14 and Figure 15 show the design of the LM3445EVM-695 printed circuit board
Figure 14. LM3445EVM-695 Top Layer Assembly Drawing (Top View)
Figure 15. LM3445EVM-695 Bottom Assembly Drawing (Bottom View)
12
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
SLUUBA8 – May 2015
Submit Documentation Feedback
Bill of Materials
www.ti.com
7
Bill of Materials
Table 3 lists the LM3445EVM-695 components list according to the schematic shown in Figure 1.
Table 3. LM3445EVM-695 Bill of Materials
Designator
Qty
Value
Description
Size
PartNumber
Manufacturer
BR1
1
400V
Diode, Switching-Bridge, 400 V, 0.8 A
MiniDIP
HD04-T
Diodes Inc.
C1
1
0.22uF
CAP, CERM, 0.22 µF, 250 V, +/- 10%, X7R
1210
GRM32DR72E224KW01L
Murata
C2
1
0.01uF
CAP, CERM, 0.01 µF, 25 V, +/- 10%, X7R
0603
GRM188R71E103KA01D
Murata
C3
1
1000pF
CAP, CERM, 1000 pF, 500 V, +/- 10%, X7R
1206
C1206C102KCRACTU
Kemet
C4
1
0.01uF
CAP, CERM, 0.01 µF, 250 V, +/- 10%, X7R
1206
C1206C103KARACTU
Kemet
C5
1
0.022uF
CAP, Film, 0.022 µF, 630 V
12.5x5.5x11
B32921C3223M289
EPCOS
C6, C10
2
22uF
CAP, AL, 22 µF, 100 V, +/- 20%, 0.8 ohm, TH
10x12.5mm
UBT2A220MPD1TD
Nichicon
C7
1
22uF
CAP, CERM, 22 µF, 25 V, +/- 10%, X5R
1210
GRM32ER61E226KE15L
Murata
C8, C15
2
0.1uF
CAP, CERM, 0.1 µF, 16 V, +/- 10%, X7R
0603
GRM188R71C104KA01D
Murata
C9
1
4.7uF
CAP, CERM, 4.7 µF, 25 V, +/- 10%, X7R
1206
GRM31CR71E475KA88L
Murata
C11
1
330pF
CAP, CERM, 330 pF, 100 V, +/- 5%, C0G/NP0
0603
GRM1885C2A331JA01D
MuRata
C12
1
0.1uF
CAP, Film, 0.1 µF, 250 V, +/- 5%,
7.2x4.5x9.5mm
R82IC3100DQ60J
Kemet
C13
1
1uF
CAP, CERM, 1 µF, 100 V, +/- 10%, X7R
1206
GRM31CR72A105KA01L
MuRata
C14
1
0.47uF
CAP, CERM, 0.47 µF, 16 V, +/- 10%, X7R
0603
GRM188R71C474KA88D
MuRata
C16
1
0.22uF
CAP, CERM, 0.22 µF, 25 V, +/- 10%
0603
GRM188R71E224KA88D
MuRata
D1
1
15V
Diode, Zener, 15 V, 225 mW
SOT-23
BZX84C15LT1G
ON Semiconductor
D2, D3, D5,
D6, D7
5
200V
Diode, Schottky, 200 V, 1 A
PowerDI123
DFLS1200-7
Diodes Inc.
D4
1
70V
Diode, P-N, 70 V, 0.2 A, SOT-323
SOT-323
BAV99WT1G
Fairchild
D8
1
200V
Diode, Superfast Rectifier, 200 V, 1 A
SMB
MURS120-13-F
Diodes Inc.
D9
1
30V
Diode, Schottky, 30 V, 0.2 A
SOD-323
BAT54HT1G
ON Semiconductor
L1
1
1mH
Inductor, Shielded, 1 mH, 0.27 A, 4.9 ohm, SMD
SMD, 7.3x7.3mm
46105C
MuRata
L2
1
3.9mH
Inductor, Wirewound, Ferrite, 3.9 mH, 0.18 A, 9.5 ohm, TH
7.8xL7.5mm
744730392
Wurth Elektronik
L3
1
1mH
Inductor, Shielded Drum Core, Ferrite, 1 mH, 0.6 A, 1.82
ohm, SMD
WE-PD-XL
74477030
Wurth Elektronik
Q1, Q7
2
250V
MOSFET, N-CH, 250 V, 4.4 A
DPAK
FDD6N25TM
Fairchild
Q2, Q3
2
40 V
Transistor, NPN, 40 V, 0.15 A
SOT-23
MMBT4401-7-F
Diodes Inc.
Q4
1
-50V
MOSFET, P-CH, -50 V, -0.13 A
SOT-323
BSS84W-7-F
Diodes Inc.
Q5
1
300 V
Transistor, PNP, 300 V, 0.2 A
SOT-23
MMBTA92
Fairchild
Q6
1
100V
MOSFET, N-CH, 100 V, 0.17 A
SOT-323
BSS123W-7-F
Diodes Inc.
Q8
1
30 V
Transistor, PNP, 30 V, 0.1 A
SOT-23
BC858CLT1G
ON Semiconductor
R1
1
866
RES, 866, 1%, 1 W
2512
CRCW2512866RFKEG
Vishay-Dale
R2
1
2.2M
RES, 2.2 M, 1%, 0.125 W
0805
RC0805FR-072M2L
Yageo America
R3
1
332k
RES, 332 k, 1%, 0.25 W
1206
CRCW1206332KFKEA
Vishay-Dale
R5, R16
2
49.9k
RES, 49.9 k, 1%, 0.1 W
0603
CRCW060349K9FKEA
Vishay-Dale
R6
1
100k
RES, 100 k, 1%, 0.25 W
1206
CRCW1206100KFKEA
Vishay-Dale
R7
1
7.50k
RES, 7.50 k, 1%, 0.1 W
0603
CRCW06037K50FKEA
Vishay-Dale
R8
1
10.0k
RES, 10.0 k, 1%, 0.1 W
0603
CRCW060310K0FKEA
Vishay-Dale
R9, R20
2
100
RES, 100, 1%, 0.125 W
0805
CRCW0805100RFKEA
Vishay-Dale
R10
1
124
RES, 124, 1%, 0.125 W
0805
CRCW0805124RFKEA
Vishay-Dale
R11
1
200k
RES, 200 k, 1%, 0.125 W
0805
CRCW0805200KFKEA
Vishay-Dale
R12, R13
2
1.00M
RES, 1.00 M, 1%, 0.125 W
0805
CRCW08051M00FKEA
Vishay-Dale
R14
1
499k
RES, 499 k, 1%, 0.1 W
0603
CRCW0603499KFKEA
Vishay-Dale
R15
1
280k
RES, 280 k, 1%, 0.1 W
0603
CRCW0603280KFKEA
Vishay-Dale
R17
1
22
RES, 22, 10%, 2 W, Fusible
Axial
EMC2-22RKI
TT Electronics
R18
1
301
RES, 301, 1%, 0.25 W
1206
CRCW1206301RFKEA
Vishay-Dale
R19
1
36.5
RES, 36.5, 1%, 0.125 W
0805
CRCW080536R5FKEA
Vishay-Dale
R21
1
1.20
RES, 1.20, 1%, 0.25 W
1206
CRCW12061R20FKEA
Vishay-Dale
R23
1
150
RES, 150, 1%, 0.125 W
0805
CRCW0805150RFKEA
Vishay-Dale
RV1
1
300Vac
SIOV Metal Oxide Leaded Varistor, 300VAC, 3500A, TH
12 x 5.6 x 14.5 mm
B72210S2301K101
EPCOS Inc
U1
1
Triac Dimmable Offline LED Driver, 10-pin MSOP, Pb-Free
MUB10A
LM3445MM/NOPB
Texas Instruments
R4
0
R22
0
SLUUBA8 – May 2015
Submit Documentation Feedback
120 VAC Valley Fill Buck Triac Dimmable LED Driver
Copyright © 2015, Texas Instruments Incorporated
13
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
