LM3S600-IQN50-C2T

TE X AS I NS TRUM E NTS - P RO DUCTION D ATA ® Stellaris LM3S600 Microcontroller D ATA SHE E T D S -LM3S 600- 1 5 8 5 2 . 2 7 4 3 S P M S 099I C o p yri g h t © 2 0 07-2014 Te xa s In stru me n ts In co rporated Copyright Copyright © 2007-2014 Texas Instruments Incorporated All rights reserved. Stellaris and StellarisWare® are registered trademarks of Texas Instruments Incorporated. ARM and Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Other names and brands may be claimed as the property of others. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Texas Instruments Incorporated 108 Wild Basin, Suite 350 Austin, TX 78746 http://www.ti.com/stellaris http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm 2 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table of Contents Revision History ............................................................................................................................. 19 About This Document .................................................................................................................... 23 Audience .............................................................................................................................................. About This Manual ................................................................................................................................ Related Documents ............................................................................................................................... Documentation Conventions .................................................................................................................. 23 23 23 24 1 Architectural Overview .......................................................................................... 26 1.1 1.2 1.3 1.4 1.4.1 1.4.2 1.4.3 1.4.4 1.4.5 1.4.6 1.4.7 1.4.8 Product Features .......................................................................................................... Target Applications ........................................................................................................ High-Level Block Diagram ............................................................................................. Functional Overview ...................................................................................................... ARM Cortex™-M3 ......................................................................................................... Motor Control Peripherals .............................................................................................. Analog Peripherals ........................................................................................................ Serial Communications Peripherals ................................................................................ System Peripherals ....................................................................................................... Memory Peripherals ...................................................................................................... Additional Features ....................................................................................................... Hardware Details .......................................................................................................... 26 31 32 34 34 35 35 35 37 37 38 38 2 The Cortex-M3 Processor ...................................................................................... 40 2.1 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.4 2.4.1 2.4.2 2.4.3 2.4.4 2.4.5 2.4.6 2.4.7 2.5 2.5.1 2.5.2 2.5.3 Block Diagram .............................................................................................................. 41 Overview ...................................................................................................................... 42 System-Level Interface .................................................................................................. 42 Integrated Configurable Debug ...................................................................................... 42 Trace Port Interface Unit (TPIU) ..................................................................................... 43 Cortex-M3 System Component Details ........................................................................... 43 Programming Model ...................................................................................................... 44 Processor Mode and Privilege Levels for Software Execution ........................................... 44 Stacks .......................................................................................................................... 44 Register Map ................................................................................................................ 45 Register Descriptions .................................................................................................... 46 Exceptions and Interrupts .............................................................................................. 59 Data Types ................................................................................................................... 59 Memory Model .............................................................................................................. 59 Memory Regions, Types and Attributes ........................................................................... 60 Memory System Ordering of Memory Accesses .............................................................. 61 Behavior of Memory Accesses ....................................................................................... 61 Software Ordering of Memory Accesses ......................................................................... 62 Bit-Banding ................................................................................................................... 63 Data Storage ................................................................................................................ 65 Synchronization Primitives ............................................................................................. 66 Exception Model ........................................................................................................... 67 Exception States ........................................................................................................... 68 Exception Types ............................................................................................................ 68 Exception Handlers ....................................................................................................... 70 July 14, 2014 3 Texas Instruments-Production Data Table of Contents 2.5.4 2.5.5 2.5.6 2.5.7 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.7 2.7.1 2.7.2 2.8 Vector Table .................................................................................................................. 71 Exception Priorities ....................................................................................................... 71 Interrupt Priority Grouping .............................................................................................. 72 Exception Entry and Return ........................................................................................... 72 Fault Handling .............................................................................................................. 74 Fault Types ................................................................................................................... 75 Fault Escalation and Hard Faults .................................................................................... 75 Fault Status Registers and Fault Address Registers ........................................................ 76 Lockup ......................................................................................................................... 76 Power Management ...................................................................................................... 76 Entering Sleep Modes ................................................................................................... 77 Wake Up from Sleep Mode ............................................................................................ 77 Instruction Set Summary ............................................................................................... 78 3 Cortex-M3 Peripherals ........................................................................................... 82 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.2 3.3 3.4 3.5 3.6 Functional Description ................................................................................................... 82 System Timer (SysTick) ................................................................................................. 82 Nested Vectored Interrupt Controller (NVIC) .................................................................... 83 System Control Block (SCB) .......................................................................................... 85 Memory Protection Unit (MPU) ....................................................................................... 85 Register Map ................................................................................................................ 90 System Timer (SysTick) Register Descriptions ................................................................ 91 NVIC Register Descriptions ........................................................................................... 95 System Control Block (SCB) Register Descriptions ........................................................ 103 Memory Protection Unit (MPU) Register Descriptions .................................................... 130 4 JTAG Interface ...................................................................................................... 140 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.4 4.5 4.5.1 4.5.2 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. JTAG Interface Pins ..................................................................................................... JTAG TAP Controller ................................................................................................... Shift Registers ............................................................................................................ Operational Considerations .......................................................................................... Initialization and Configuration ..................................................................................... Register Descriptions .................................................................................................. Instruction Register (IR) ............................................................................................... Data Registers ............................................................................................................ 141 141 142 142 143 144 144 146 146 146 148 5 System Control ..................................................................................................... 150 5.1 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.3 5.4 5.5 Signal Description ....................................................................................................... Functional Description ................................................................................................. Device Identification .................................................................................................... Reset Control .............................................................................................................. Power Control ............................................................................................................. Clock Control .............................................................................................................. System Control ........................................................................................................... Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 4 150 150 150 150 155 155 158 159 160 161 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 6 Internal Memory ................................................................................................... 205 6.1 6.2 6.2.1 6.2.2 6.3 6.3.1 6.3.2 6.4 6.5 6.6 Block Diagram ............................................................................................................ 205 Functional Description ................................................................................................. 205 SRAM Memory ............................................................................................................ 205 Flash Memory ............................................................................................................. 206 Flash Memory Initialization and Configuration ............................................................... 209 Changing Flash Protection Bits .................................................................................... 209 Flash Programming ..................................................................................................... 210 Register Map .............................................................................................................. 211 Flash Register Descriptions (Flash Control Offset) ......................................................... 211 Flash Register Descriptions (System Control Offset) ...................................................... 219 7 General-Purpose Input/Outputs (GPIOs) ........................................................... 223 7.1 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.3 7.4 7.5 Signal Description ....................................................................................................... 223 Functional Description ................................................................................................. 226 Data Control ............................................................................................................... 227 Interrupt Control .......................................................................................................... 228 Mode Control .............................................................................................................. 228 Pad Control ................................................................................................................. 228 Identification ............................................................................................................... 228 Initialization and Configuration ..................................................................................... 228 Register Map .............................................................................................................. 230 Register Descriptions .................................................................................................. 231 8 General-Purpose Timers ...................................................................................... 263 8.1 8.2 8.3 8.3.1 8.3.2 8.3.3 8.4 8.4.1 8.4.2 8.4.3 8.4.4 8.4.5 8.4.6 8.5 8.6 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. GPTM Reset Conditions .............................................................................................. 32-Bit Timer Operating Modes ...................................................................................... 16-Bit Timer Operating Modes ...................................................................................... Initialization and Configuration ..................................................................................... 32-Bit One-Shot/Periodic Timer Mode ........................................................................... 32-Bit Real-Time Clock (RTC) Mode ............................................................................. 16-Bit One-Shot/Periodic Timer Mode ........................................................................... 16-Bit Input Edge Count Mode ..................................................................................... 16-Bit Input Edge Timing Mode .................................................................................... 16-Bit PWM Mode ....................................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 263 264 265 265 265 266 270 270 271 271 272 272 273 273 274 9 Watchdog Timer ................................................................................................... 299 9.1 9.2 9.3 9.4 9.5 Block Diagram ............................................................................................................ Functional Description ................................................................................................. Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 300 300 301 301 302 10 Universal Asynchronous Receivers/Transmitters (UARTs) ............................. 323 10.1 10.2 Block Diagram ............................................................................................................ 324 Signal Description ....................................................................................................... 324 July 14, 2014 5 Texas Instruments-Production Data Table of Contents 10.3 10.3.1 10.3.2 10.3.3 10.3.4 10.3.5 10.3.6 10.4 10.5 10.6 Functional Description ................................................................................................. Transmit/Receive Logic ............................................................................................... Baud-Rate Generation ................................................................................................. Data Transmission ...................................................................................................... FIFO Operation ........................................................................................................... Interrupts .................................................................................................................... Loopback Operation .................................................................................................... Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 325 325 325 326 326 327 328 328 329 330 11 Synchronous Serial Interface (SSI) .................................................................... 363 11.1 11.2 11.3 11.3.1 11.3.2 11.3.3 11.3.4 11.4 11.5 11.6 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. Bit Rate Generation ..................................................................................................... FIFO Operation ........................................................................................................... Interrupts .................................................................................................................... Frame Formats ........................................................................................................... Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 12 Inter-Integrated Circuit (I2C) Interface ................................................................ 401 12.1 12.2 12.3 12.3.1 12.3.2 12.3.3 12.3.4 12.3.5 12.4 12.5 12.6 12.7 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. I2C Bus Functional Overview ........................................................................................ Available Speed Modes ............................................................................................... Interrupts .................................................................................................................... Loopback Operation .................................................................................................... Command Sequence Flow Charts ................................................................................ Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions (I2C Master) ............................................................................... Register Descriptions (I2C Slave) ................................................................................. 363 363 364 364 364 365 365 373 374 375 402 402 402 403 405 406 406 406 414 415 416 429 13 Analog Comparators ............................................................................................ 438 13.1 13.2 13.3 13.3.1 13.4 13.5 13.6 Block Diagram ............................................................................................................ Signal Description ....................................................................................................... Functional Description ................................................................................................. Internal Reference Programming .................................................................................. Initialization and Configuration ..................................................................................... Register Map .............................................................................................................. Register Descriptions .................................................................................................. 14 Pin Diagram .......................................................................................................... 451 439 439 440 441 442 443 443 15 Signal Tables ........................................................................................................ 452 15.1 15.2 15.3 Signals by Pin Number ................................................................................................ 452 Signals by Signal Name ............................................................................................... 454 Signals by Function, Except for GPIO ........................................................................... 456 6 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 15.4 15.5 GPIO Pins and Alternate Functions .............................................................................. 458 Connections for Unused Signals ................................................................................... 459 16 Operating Characteristics ................................................................................... 460 17 Electrical Characteristics .................................................................................... 461 17.1 17.1.1 17.1.2 17.1.3 17.1.4 17.1.5 17.1.6 17.2 17.2.1 17.2.2 17.2.3 17.2.4 17.2.5 17.2.6 17.2.7 17.2.8 17.2.9 DC Characteristics ...................................................................................................... 461 Maximum Ratings ....................................................................................................... 461 Recommended DC Operating Conditions ...................................................................... 461 On-Chip Low Drop-Out (LDO) Regulator Characteristics ................................................ 462 GPIO Module Characteristics ....................................................................................... 462 Power Specifications ................................................................................................... 462 Flash Memory Characteristics ...................................................................................... 463 AC Characteristics ....................................................................................................... 463 Load Conditions .......................................................................................................... 463 Clocks ........................................................................................................................ 464 JTAG and Boundary Scan ............................................................................................ 464 Reset ......................................................................................................................... 466 Sleep Modes ............................................................................................................... 468 General-Purpose I/O (GPIO) ........................................................................................ 468 Synchronous Serial Interface (SSI) ............................................................................... 469 Inter-Integrated Circuit (I2C) Interface ........................................................................... 470 Analog Comparator ..................................................................................................... 471 A Serial Flash Loader .............................................................................................. 472 A.1 A.2 A.2.1 A.2.2 A.3 A.3.1 A.3.2 A.3.3 A.4 A.4.1 A.4.2 A.4.3 A.4.4 A.4.5 A.4.6 Serial Flash Loader ..................................................................................................... Interfaces ................................................................................................................... UART ......................................................................................................................... SSI ............................................................................................................................. Packet Handling .......................................................................................................... Packet Format ............................................................................................................ Sending Packets ......................................................................................................... Receiving Packets ....................................................................................................... Commands ................................................................................................................. COMMAND_PING (0X20) ............................................................................................ COMMAND_GET_STATUS (0x23) ............................................................................... COMMAND_DOWNLOAD (0x21) ................................................................................. COMMAND_SEND_DATA (0x24) ................................................................................. COMMAND_RUN (0x22) ............................................................................................. COMMAND_RESET (0x25) ......................................................................................... B Register Quick Reference ................................................................................... 477 472 472 472 472 473 473 473 473 474 474 474 474 475 475 475 C Ordering and Contact Information ..................................................................... 493 C.1 C.2 C.3 C.4 Ordering Information .................................................................................................... 493 Part Markings .............................................................................................................. 493 Kits ............................................................................................................................. 493 Support Information ..................................................................................................... 494 D Package Information ............................................................................................ 495 D.1 D.1.1 D.1.2 48-Pin LQFP Package ................................................................................................. 495 Package Dimensions ................................................................................................... 495 Tray Dimensions ......................................................................................................... 497 July 14, 2014 7 Texas Instruments-Production Data Table of Contents D.1.3 Tape and Reel Dimensions .......................................................................................... 499 8 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller List of Figures Figure 1-1. Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-7. Figure 3-1. Figure 4-1. Figure 4-2. Figure 4-3. Figure 4-4. Figure 4-5. Figure 5-1. Figure 5-2. Figure 5-3. Figure 5-4. Figure 6-1. Figure 7-1. Figure 7-2. Figure 7-3. Figure 8-1. Figure 8-2. Figure 8-3. Figure 8-4. Figure 9-1. Figure 10-1. Figure 10-2. Figure 11-1. Figure 11-2. Figure 11-3. Figure 11-4. Figure 11-5. Figure 11-6. Figure 11-7. Figure 11-8. Figure 11-9. Figure 11-10. Figure 11-11. Figure 11-12. Figure 12-1. Figure 12-2. Figure 12-3. Figure 12-4. Figure 12-5. Stellaris LM3S600 Microcontroller High-Level Block Diagram ................................. 33 CPU Block Diagram ............................................................................................. 42 TPIU Block Diagram ............................................................................................ 43 Cortex-M3 Register Set ........................................................................................ 45 Bit-Band Mapping ................................................................................................ 65 Data Storage ....................................................................................................... 66 Vector Table ........................................................................................................ 71 Exception Stack Frame ........................................................................................ 73 SRD Use Example ............................................................................................... 88 JTAG Module Block Diagram .............................................................................. 141 Test Access Port State Machine ......................................................................... 144 IDCODE Register Format ................................................................................... 148 BYPASS Register Format ................................................................................... 149 Boundary Scan Register Format ......................................................................... 149 Basic RST Configuration .................................................................................... 152 External Circuitry to Extend Power-On Reset ....................................................... 152 Reset Circuit Controlled by Switch ...................................................................... 153 Main Clock Tree ................................................................................................ 156 Flash Block Diagram .......................................................................................... 205 GPIO Port Block Diagram ................................................................................... 226 GPIODATA Write Example ................................................................................. 227 GPIODATA Read Example ................................................................................. 227 GPTM Module Block Diagram ............................................................................ 264 16-Bit Input Edge Count Mode Example .............................................................. 268 16-Bit Input Edge Time Mode Example ............................................................... 269 16-Bit PWM Mode Example ................................................................................ 270 WDT Module Block Diagram .............................................................................. 300 UART Module Block Diagram ............................................................................. 324 UART Character Frame ..................................................................................... 325 SSI Module Block Diagram ................................................................................. 363 TI Synchronous Serial Frame Format (Single Transfer) ........................................ 366 TI Synchronous Serial Frame Format (Continuous Transfer) ................................ 367 Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 .......................... 367 Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 .................. 368 Freescale SPI Frame Format with SPO=0 and SPH=1 ......................................... 369 Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 ............... 369 Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 ........ 370 Freescale SPI Frame Format with SPO=1 and SPH=1 ......................................... 371 MICROWIRE Frame Format (Single Frame) ........................................................ 371 MICROWIRE Frame Format (Continuous Transfer) ............................................. 372 MICROWIRE Frame Format, SSIFss Input Setup and Hold Requirements ............ 373 I2C Block Diagram ............................................................................................. 402 I2C Bus Configuration ........................................................................................ 403 START and STOP Conditions ............................................................................. 403 Complete Data Transfer with a 7-Bit Address ....................................................... 404 R/S Bit in First Byte ............................................................................................ 404 July 14, 2014 9 Texas Instruments-Production Data Table of Contents Data Validity During Bit Transfer on the I2C Bus ................................................... 404 Master Single SEND .......................................................................................... 408 Master Single RECEIVE ..................................................................................... 409 Master Burst SEND ........................................................................................... 410 Master Burst RECEIVE ...................................................................................... 411 Master Burst RECEIVE after Burst SEND ............................................................ 412 Master Burst SEND after Burst RECEIVE ............................................................ 413 Slave Command Sequence ................................................................................ 414 Analog Comparator Module Block Diagram ......................................................... 439 Structure of Comparator Unit .............................................................................. 440 Comparator Internal Reference Structure ............................................................ 442 48-Pin QFP Package Pin Diagram ...................................................................... 451 Load Conditions ................................................................................................ 464 JTAG Test Clock Input Timing ............................................................................. 465 JTAG Test Access Port (TAP) Timing .................................................................. 465 JTAG TRST Timing ............................................................................................ 466 External Reset Timing (RST) .............................................................................. 466 Power-On Reset Timing ..................................................................................... 467 Brown-Out Reset Timing .................................................................................... 467 Software Reset Timing ....................................................................................... 467 Watchdog Reset Timing ..................................................................................... 468 LDO Reset Timing ............................................................................................. 468 SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing Measurement .................................................................................................... 469 Figure 17-12. SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer ................. 470 Figure 17-13. SSI Timing for SPI Frame Format (FRF=00), with SPH=1 ..................................... 470 Figure 17-14. I2C Timing ......................................................................................................... 471 Figure D-1. Stellaris LM3S600 48-Pin LQFP Package ........................................................... 495 Figure D-2. 48-Pin LQFP Tray Dimensions ........................................................................... 497 Figure D-3. 48-Pin LQFP Tape and Reel Dimensions ............................................................. 499 Figure 12-6. Figure 12-7. Figure 12-8. Figure 12-9. Figure 12-10. Figure 12-11. Figure 12-12. Figure 12-13. Figure 13-1. Figure 13-2. Figure 13-3. Figure 14-1. Figure 17-1. Figure 17-2. Figure 17-3. Figure 17-4. Figure 17-5. Figure 17-6. Figure 17-7. Figure 17-8. Figure 17-9. Figure 17-10. Figure 17-11. 10 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller List of Tables Table 1. Table 2. Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 2-5. Table 2-6. Table 2-7. Table 2-8. Table 2-9. Table 2-10. Table 2-11. Table 2-12. Table 2-13. Table 3-1. Table 3-2. Table 3-3. Table 3-4. Table 3-5. Table 3-6. Table 3-7. Table 3-8. Table 3-9. Table 4-1. Table 4-2. Table 4-3. Table 5-1. Table 5-2. Table 5-3. Table 5-4. Table 5-5. Table 5-6. Table 6-1. Table 6-2. Table 7-1. Table 7-2. Table 7-3. Table 7-4. Table 7-5. Table 7-6. Table 8-1. Table 8-2. Table 8-3. Table 8-4. Table 9-1. Revision History .................................................................................................. 19 Documentation Conventions ................................................................................ 24 Summary of Processor Mode, Privilege Level, and Stack Use ................................ 45 Processor Register Map ....................................................................................... 46 PSR Register Combinations ................................................................................. 51 Memory Map ....................................................................................................... 59 Memory Access Behavior ..................................................................................... 61 SRAM Memory Bit-Banding Regions .................................................................... 63 Peripheral Memory Bit-Banding Regions ............................................................... 63 Exception Types .................................................................................................. 69 Interrupts ............................................................................................................ 70 Exception Return Behavior ................................................................................... 74 Faults ................................................................................................................. 75 Fault Status and Fault Address Registers .............................................................. 76 Cortex-M3 Instruction Summary ........................................................................... 78 Core Peripheral Register Regions ......................................................................... 82 Memory Attributes Summary ................................................................................ 85 TEX, S, C, and B Bit Field Encoding ..................................................................... 88 Cache Policy for Memory Attribute Encoding ......................................................... 89 AP Bit Field Encoding .......................................................................................... 89 Memory Region Attributes for Stellaris Microcontrollers .......................................... 89 Peripherals Register Map ..................................................................................... 90 Interrupt Priority Levels ...................................................................................... 109 Example SIZE Field Values ................................................................................ 137 JTAG_SWD_SWO Signals (48QFP) ................................................................... 141 JTAG Port Pins Reset State ............................................................................... 142 JTAG Instruction Register Commands ................................................................. 146 System Control & Clocks Signals (48QFP) .......................................................... 150 Reset Sources ................................................................................................... 151 Clock Source Options ........................................................................................ 155 Possible System Clock Frequencies Using the SYSDIV Field ............................... 156 System Control Register Map ............................................................................. 160 PLL Mode Control .............................................................................................. 172 Flash Protection Policy Combinations ................................................................. 206 Flash Register Map ............................................................................................ 211 GPIO Pins With Non-Zero Reset Values .............................................................. 224 GPIO Pins and Alternate Functions (48QFP) ....................................................... 224 GPIO Signals (48QFP) ....................................................................................... 225 GPIO Pad Configuration Examples ..................................................................... 229 GPIO Interrupt Configuration Example ................................................................ 229 GPIO Register Map ........................................................................................... 230 Available CCP Pins ............................................................................................ 264 General-Purpose Timers Signals (48QFP) ........................................................... 264 16-Bit Timer With Prescaler Configurations ......................................................... 267 Timers Register Map .......................................................................................... 273 Watchdog Timer Register Map ............................................................................ 301 July 14, 2014 11 Texas Instruments-Production Data Table of Contents Table 10-1. Table 10-2. Table 11-1. Table 11-2. Table 12-1. Table 12-2. Table 12-3. Table 12-4. Table 13-1. Table 13-2. Table 13-3. Table 13-4. Table 13-5. Table 13-6. Table 15-1. Table 15-2. Table 15-3. Table 15-4. Table 15-5. Table 16-1. Table 16-2. Table 16-3. Table 17-1. Table 17-2. Table 17-3. Table 17-4. Table 17-5. Table 17-6. Table 17-7. Table 17-8. Table 17-9. Table 17-10. Table 17-11. Table 17-12. Table 17-13. Table 17-14. Table 17-15. Table 17-16. UART Signals (48QFP) ...................................................................................... 324 UART Register Map ........................................................................................... 329 SSI Signals (48QFP) .......................................................................................... 364 SSI Register Map .............................................................................................. 374 I2C Signals (48QFP) .......................................................................................... 402 Examples of I2C Master Timer Period versus Speed Mode ................................... 405 Inter-Integrated Circuit (I2C) Interface Register Map ............................................. 415 Write Field Decoding for I2CMCS[3:0] Field (Sheet 1 of 3) .................................... 420 Analog Comparators Signals (48QFP) ................................................................ 439 Comparator 0 Operating Modes ......................................................................... 441 Comparator 1 Operating Modes .......................................................................... 441 Comparator 2 Operating Modes .......................................................................... 441 Internal Reference Voltage and ACREFCTL Field Values ..................................... 442 Analog Comparators Register Map ..................................................................... 443 Signals by Pin Number ....................................................................................... 452 Signals by Signal Name ..................................................................................... 454 Signals by Function, Except for GPIO ................................................................. 456 GPIO Pins and Alternate Functions ..................................................................... 458 Connections for Unused Signals ......................................................................... 459 Temperature Characteristics ............................................................................... 460 Thermal Characteristics ..................................................................................... 460 ESD Absolute Maximum Ratings ........................................................................ 460 Maximum Ratings .............................................................................................. 461 Recommended DC Operating Conditions ............................................................ 461 LDO Regulator Characteristics ........................................................................... 462 GPIO Module DC Characteristics ........................................................................ 462 Detailed Power Specifications ............................................................................ 463 Flash Memory Characteristics ............................................................................ 463 Phase Locked Loop (PLL) Characteristics ........................................................... 464 Clock Characteristics ......................................................................................... 464 JTAG Characteristics ......................................................................................... 464 Reset Characteristics ......................................................................................... 466 Sleep Modes AC Characteristics ......................................................................... 468 GPIO Characteristics ......................................................................................... 468 SSI Characteristics ............................................................................................ 469 I2C Characteristics ............................................................................................. 470 Analog Comparator Characteristics ..................................................................... 471 Analog Comparator Voltage Reference Characteristics ........................................ 471 12 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller List of Registers The Cortex-M3 Processor ............................................................................................................. 40 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Cortex General-Purpose Register 0 (R0) ........................................................................... 47 Cortex General-Purpose Register 1 (R1) ........................................................................... 47 Cortex General-Purpose Register 2 (R2) ........................................................................... 47 Cortex General-Purpose Register 3 (R3) ........................................................................... 47 Cortex General-Purpose Register 4 (R4) ........................................................................... 47 Cortex General-Purpose Register 5 (R5) ........................................................................... 47 Cortex General-Purpose Register 6 (R6) ........................................................................... 47 Cortex General-Purpose Register 7 (R7) ........................................................................... 47 Cortex General-Purpose Register 8 (R8) ........................................................................... 47 Cortex General-Purpose Register 9 (R9) ........................................................................... 47 Cortex General-Purpose Register 10 (R10) ....................................................................... 47 Cortex General-Purpose Register 11 (R11) ........................................................................ 47 Cortex General-Purpose Register 12 (R12) ....................................................................... 47 Stack Pointer (SP) ........................................................................................................... 48 Link Register (LR) ............................................................................................................ 49 Program Counter (PC) ..................................................................................................... 50 Program Status Register (PSR) ........................................................................................ 51 Priority Mask Register (PRIMASK) .................................................................................... 55 Fault Mask Register (FAULTMASK) .................................................................................. 56 Base Priority Mask Register (BASEPRI) ............................................................................ 57 Control Register (CONTROL) ........................................................................................... 58 Cortex-M3 Peripherals ................................................................................................................... 82 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: SysTick Control and Status Register (STCTRL), offset 0x010 ............................................. 92 SysTick Reload Value Register (STRELOAD), offset 0x014 ................................................ 94 SysTick Current Value Register (STCURRENT), offset 0x018 ............................................. 95 Interrupt 0-29 Set Enable (EN0), offset 0x100 .................................................................... 96 Interrupt 0-29 Clear Enable (DIS0), offset 0x180 ................................................................ 97 Interrupt 0-29 Set Pending (PEND0), offset 0x200 ............................................................. 98 Interrupt 0-29 Clear Pending (UNPEND0), offset 0x280 ..................................................... 99 Interrupt 0-29 Active Bit (ACTIVE0), offset 0x300 ............................................................. 100 Interrupt 0-3 Priority (PRI0), offset 0x400 ......................................................................... 101 Interrupt 4-7 Priority (PRI1), offset 0x404 ......................................................................... 101 Interrupt 8-11 Priority (PRI2), offset 0x408 ....................................................................... 101 Interrupt 12-15 Priority (PRI3), offset 0x40C .................................................................... 101 Interrupt 16-19 Priority (PRI4), offset 0x410 ..................................................................... 101 Interrupt 20-23 Priority (PRI5), offset 0x414 ..................................................................... 101 Interrupt 24-27 Priority (PRI6), offset 0x418 ..................................................................... 101 Interrupt 28-29 Priority (PRI7), offset 0x41C .................................................................... 101 Software Trigger Interrupt (SWTRIG), offset 0xF00 .......................................................... 103 CPU ID Base (CPUID), offset 0xD00 ............................................................................... 104 Interrupt Control and State (INTCTRL), offset 0xD04 ........................................................ 105 Vector Table Offset (VTABLE), offset 0xD08 .................................................................... 108 Application Interrupt and Reset Control (APINT), offset 0xD0C ......................................... 109 System Control (SYSCTRL), offset 0xD10 ....................................................................... 111 July 14, 2014 13 Texas Instruments-Production Data Table of Contents Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: Register 31: Register 32: Register 33: Register 34: Register 35: Register 36: Register 37: Register 38: Register 39: Register 40: Register 41: Register 42: Configuration and Control (CFGCTRL), offset 0xD14 ....................................................... 113 System Handler Priority 1 (SYSPRI1), offset 0xD18 ......................................................... 115 System Handler Priority 2 (SYSPRI2), offset 0xD1C ........................................................ 116 System Handler Priority 3 (SYSPRI3), offset 0xD20 ......................................................... 117 System Handler Control and State (SYSHNDCTRL), offset 0xD24 .................................... 118 Configurable Fault Status (FAULTSTAT), offset 0xD28 ..................................................... 122 Hard Fault Status (HFAULTSTAT), offset 0xD2C .............................................................. 128 Memory Management Fault Address (MMADDR), offset 0xD34 ........................................ 129 Bus Fault Address (FAULTADDR), offset 0xD38 .............................................................. 130 MPU Type (MPUTYPE), offset 0xD90 ............................................................................. 131 MPU Control (MPUCTRL), offset 0xD94 .......................................................................... 132 MPU Region Number (MPUNUMBER), offset 0xD98 ....................................................... 134 MPU Region Base Address (MPUBASE), offset 0xD9C ................................................... 135 MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4 ....................................... 135 MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC ...................................... 135 MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4 ....................................... 135 MPU Region Attribute and Size (MPUATTR), offset 0xDA0 ............................................... 137 MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8 .................................. 137 MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0 .................................. 137 MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8 .................................. 137 System Control ............................................................................................................................ 150 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Device Identification 0 (DID0), offset 0x000 ..................................................................... 162 Power-On and Brown-Out Reset Control (PBORCTL), offset 0x030 .................................. 164 LDO Power Control (LDOPCTL), offset 0x034 ................................................................. 165 Raw Interrupt Status (RIS), offset 0x050 .......................................................................... 166 Interrupt Mask Control (IMC), offset 0x054 ...................................................................... 167 Masked Interrupt Status and Clear (MISC), offset 0x058 .................................................. 168 Reset Cause (RESC), offset 0x05C ................................................................................ 169 Run-Mode Clock Configuration (RCC), offset 0x060 ......................................................... 170 XTAL to PLL Translation (PLLCFG), offset 0x064 ............................................................. 173 Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144 ........................................ 174 Clock Verification Clear (CLKVCLR), offset 0x150 ............................................................ 175 Allow Unregulated LDO to Reset the Part (LDOARST), offset 0x160 ................................. 176 Device Identification 1 (DID1), offset 0x004 ..................................................................... 177 Device Capabilities 0 (DC0), offset 0x008 ........................................................................ 179 Device Capabilities 1 (DC1), offset 0x010 ........................................................................ 180 Device Capabilities 2 (DC2), offset 0x014 ........................................................................ 182 Device Capabilities 3 (DC3), offset 0x018 ........................................................................ 184 Device Capabilities 4 (DC4), offset 0x01C ....................................................................... 186 Run Mode Clock Gating Control Register 0 (RCGC0), offset 0x100 ................................... 187 Sleep Mode Clock Gating Control Register 0 (SCGC0), offset 0x110 ................................. 188 Deep Sleep Mode Clock Gating Control Register 0 (DCGC0), offset 0x120 ....................... 189 Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104 ................................... 190 Sleep Mode Clock Gating Control Register 1 (SCGC1), offset 0x114 ................................. 192 Deep Sleep Mode Clock Gating Control Register 1 (DCGC1), offset 0x124 ....................... 194 Run Mode Clock Gating Control Register 2 (RCGC2), offset 0x108 ................................... 196 Sleep Mode Clock Gating Control Register 2 (SCGC2), offset 0x118 ................................. 197 Deep Sleep Mode Clock Gating Control Register 2 (DCGC2), offset 0x128 ....................... 199 14 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 28: Register 29: Register 30: Software Reset Control 0 (SRCR0), offset 0x040 ............................................................. 201 Software Reset Control 1 (SRCR1), offset 0x044 ............................................................. 202 Software Reset Control 2 (SRCR2), offset 0x048 ............................................................. 204 Internal Memory ........................................................................................................................... 205 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Flash Memory Address (FMA), offset 0x000 .................................................................... 212 Flash Memory Data (FMD), offset 0x004 ......................................................................... 213 Flash Memory Control (FMC), offset 0x008 ..................................................................... 214 Flash Controller Raw Interrupt Status (FCRIS), offset 0x00C ............................................ 216 Flash Controller Interrupt Mask (FCIM), offset 0x010 ........................................................ 217 Flash Controller Masked Interrupt Status and Clear (FCMISC), offset 0x014 ..................... 218 USec Reload (USECRL), offset 0x140 ............................................................................ 220 Flash Memory Protection Read Enable (FMPRE), offset 0x130 ......................................... 221 Flash Memory Protection Program Enable (FMPPE), offset 0x134 .................................... 222 General-Purpose Input/Outputs (GPIOs) ................................................................................... 223 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: Register 25: Register 26: Register 27: Register 28: Register 29: Register 30: GPIO Data (GPIODATA), offset 0x000 ............................................................................ 232 GPIO Direction (GPIODIR), offset 0x400 ......................................................................... 233 GPIO Interrupt Sense (GPIOIS), offset 0x404 .................................................................. 234 GPIO Interrupt Both Edges (GPIOIBE), offset 0x408 ........................................................ 235 GPIO Interrupt Event (GPIOIEV), offset 0x40C ................................................................ 236 GPIO Interrupt Mask (GPIOIM), offset 0x410 ................................................................... 237 GPIO Raw Interrupt Status (GPIORIS), offset 0x414 ........................................................ 238 GPIO Masked Interrupt Status (GPIOMIS), offset 0x418 ................................................... 239 GPIO Interrupt Clear (GPIOICR), offset 0x41C ................................................................ 240 GPIO Alternate Function Select (GPIOAFSEL), offset 0x420 ............................................ 241 GPIO 2-mA Drive Select (GPIODR2R), offset 0x500 ........................................................ 243 GPIO 4-mA Drive Select (GPIODR4R), offset 0x504 ........................................................ 244 GPIO 8-mA Drive Select (GPIODR8R), offset 0x508 ........................................................ 245 GPIO Open Drain Select (GPIOODR), offset 0x50C ......................................................... 246 GPIO Pull-Up Select (GPIOPUR), offset 0x510 ................................................................ 247 GPIO Pull-Down Select (GPIOPDR), offset 0x514 ........................................................... 248 GPIO Slew Rate Control Select (GPIOSLR), offset 0x518 ................................................ 249 GPIO Digital Enable (GPIODEN), offset 0x51C ................................................................ 250 GPIO Peripheral Identification 4 (GPIOPeriphID4), offset 0xFD0 ....................................... 251 GPIO Peripheral Identification 5 (GPIOPeriphID5), offset 0xFD4 ....................................... 252 GPIO Peripheral Identification 6 (GPIOPeriphID6), offset 0xFD8 ....................................... 253 GPIO Peripheral Identification 7 (GPIOPeriphID7), offset 0xFDC ...................................... 254 GPIO Peripheral Identification 0 (GPIOPeriphID0), offset 0xFE0 ....................................... 255 GPIO Peripheral Identification 1 (GPIOPeriphID1), offset 0xFE4 ....................................... 256 GPIO Peripheral Identification 2 (GPIOPeriphID2), offset 0xFE8 ....................................... 257 GPIO Peripheral Identification 3 (GPIOPeriphID3), offset 0xFEC ...................................... 258 GPIO PrimeCell Identification 0 (GPIOPCellID0), offset 0xFF0 .......................................... 259 GPIO PrimeCell Identification 1 (GPIOPCellID1), offset 0xFF4 .......................................... 260 GPIO PrimeCell Identification 2 (GPIOPCellID2), offset 0xFF8 .......................................... 261 GPIO PrimeCell Identification 3 (GPIOPCellID3), offset 0xFFC ......................................... 262 General-Purpose Timers ............................................................................................................. 263 Register 1: Register 2: Register 3: GPTM Configuration (GPTMCFG), offset 0x000 .............................................................. 275 GPTM TimerA Mode (GPTMTAMR), offset 0x004 ............................................................ 276 GPTM TimerB Mode (GPTMTBMR), offset 0x008 ............................................................ 278 July 14, 2014 15 Texas Instruments-Production Data Table of Contents Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: GPTM Control (GPTMCTL), offset 0x00C ........................................................................ 280 GPTM Interrupt Mask (GPTMIMR), offset 0x018 .............................................................. 283 GPTM Raw Interrupt Status (GPTMRIS), offset 0x01C ..................................................... 285 GPTM Masked Interrupt Status (GPTMMIS), offset 0x020 ................................................ 286 GPTM Interrupt Clear (GPTMICR), offset 0x024 .............................................................. 287 GPTM TimerA Interval Load (GPTMTAILR), offset 0x028 ................................................. 289 GPTM TimerB Interval Load (GPTMTBILR), offset 0x02C ................................................ 290 GPTM TimerA Match (GPTMTAMATCHR), offset 0x030 ................................................... 291 GPTM TimerB Match (GPTMTBMATCHR), offset 0x034 .................................................. 292 GPTM TimerA Prescale (GPTMTAPR), offset 0x038 ........................................................ 293 GPTM TimerB Prescale (GPTMTBPR), offset 0x03C ....................................................... 294 GPTM TimerA Prescale Match (GPTMTAPMR), offset 0x040 ........................................... 295 GPTM TimerB Prescale Match (GPTMTBPMR), offset 0x044 ........................................... 296 GPTM TimerA (GPTMTAR), offset 0x048 ........................................................................ 297 GPTM TimerB (GPTMTBR), offset 0x04C ....................................................................... 298 Watchdog Timer ........................................................................................................................... 299 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Watchdog Load (WDTLOAD), offset 0x000 ...................................................................... 303 Watchdog Value (WDTVALUE), offset 0x004 ................................................................... 304 Watchdog Control (WDTCTL), offset 0x008 ..................................................................... 305 Watchdog Interrupt Clear (WDTICR), offset 0x00C .......................................................... 306 Watchdog Raw Interrupt Status (WDTRIS), offset 0x010 .................................................. 307 Watchdog Masked Interrupt Status (WDTMIS), offset 0x014 ............................................. 308 Watchdog Test (WDTTEST), offset 0x418 ....................................................................... 309 Watchdog Lock (WDTLOCK), offset 0xC00 ..................................................................... 310 Watchdog Peripheral Identification 4 (WDTPeriphID4), offset 0xFD0 ................................. 311 Watchdog Peripheral Identification 5 (WDTPeriphID5), offset 0xFD4 ................................. 312 Watchdog Peripheral Identification 6 (WDTPeriphID6), offset 0xFD8 ................................. 313 Watchdog Peripheral Identification 7 (WDTPeriphID7), offset 0xFDC ................................ 314 Watchdog Peripheral Identification 0 (WDTPeriphID0), offset 0xFE0 ................................. 315 Watchdog Peripheral Identification 1 (WDTPeriphID1), offset 0xFE4 ................................. 316 Watchdog Peripheral Identification 2 (WDTPeriphID2), offset 0xFE8 ................................. 317 Watchdog Peripheral Identification 3 (WDTPeriphID3), offset 0xFEC ................................. 318 Watchdog PrimeCell Identification 0 (WDTPCellID0), offset 0xFF0 .................................... 319 Watchdog PrimeCell Identification 1 (WDTPCellID1), offset 0xFF4 .................................... 320 Watchdog PrimeCell Identification 2 (WDTPCellID2), offset 0xFF8 .................................... 321 Watchdog PrimeCell Identification 3 (WDTPCellID3 ), offset 0xFFC .................................. 322 Universal Asynchronous Receivers/Transmitters (UARTs) ..................................................... 323 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: UART Data (UARTDR), offset 0x000 ............................................................................... 331 UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 ........................... 333 UART Flag (UARTFR), offset 0x018 ................................................................................ 335 UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 ............................................ 337 UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 ....................................... 338 UART Line Control (UARTLCRH), offset 0x02C ............................................................... 339 UART Control (UARTCTL), offset 0x030 ......................................................................... 341 UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 ........................................... 343 UART Interrupt Mask (UARTIM), offset 0x038 ................................................................. 345 UART Raw Interrupt Status (UARTRIS), offset 0x03C ...................................................... 347 UART Masked Interrupt Status (UARTMIS), offset 0x040 ................................................. 348 16 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: Register 22: Register 23: Register 24: UART Interrupt Clear (UARTICR), offset 0x044 ............................................................... 349 UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 ..................................... 351 UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 ..................................... 352 UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 ..................................... 353 UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC ..................................... 354 UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 ...................................... 355 UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 ...................................... 356 UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 ...................................... 357 UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC ..................................... 358 UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 ........................................ 359 UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 ........................................ 360 UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 ........................................ 361 UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC ........................................ 362 Synchronous Serial Interface (SSI) ............................................................................................ 363 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: Register 12: Register 13: Register 14: Register 15: Register 16: Register 17: Register 18: Register 19: Register 20: Register 21: SSI Control 0 (SSICR0), offset 0x000 .............................................................................. 376 SSI Control 1 (SSICR1), offset 0x004 .............................................................................. 378 SSI Data (SSIDR), offset 0x008 ...................................................................................... 380 SSI Status (SSISR), offset 0x00C ................................................................................... 381 SSI Clock Prescale (SSICPSR), offset 0x010 .................................................................. 383 SSI Interrupt Mask (SSIIM), offset 0x014 ......................................................................... 384 SSI Raw Interrupt Status (SSIRIS), offset 0x018 .............................................................. 386 SSI Masked Interrupt Status (SSIMIS), offset 0x01C ........................................................ 387 SSI Interrupt Clear (SSIICR), offset 0x020 ....................................................................... 388 SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 ............................................. 389 SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 ............................................. 390 SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 ............................................. 391 SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC ............................................ 392 SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 ............................................. 393 SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 ............................................. 394 SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 ............................................. 395 SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC ............................................ 396 SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 ............................................... 397 SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 ............................................... 398 SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 ............................................... 399 SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC ............................................... 400 Inter-Integrated Circuit (I2C) Interface ........................................................................................ 401 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Register 11: I2C Master Slave Address (I2CMSA), offset 0x000 ........................................................... 417 I2C Master Control/Status (I2CMCS), offset 0x004 ........................................................... 418 I2C Master Data (I2CMDR), offset 0x008 ......................................................................... 422 I2C Master Timer Period (I2CMTPR), offset 0x00C ........................................................... 423 I2C Master Interrupt Mask (I2CMIMR), offset 0x010 ......................................................... 424 I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 ................................................. 425 I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 ........................................... 426 I2C Master Interrupt Clear (I2CMICR), offset 0x01C ......................................................... 427 I2C Master Configuration (I2CMCR), offset 0x020 ............................................................ 428 I2C Slave Own Address (I2CSOAR), offset 0x800 ............................................................ 430 I2C Slave Control/Status (I2CSCSR), offset 0x804 ........................................................... 431 July 14, 2014 17 Texas Instruments-Production Data Table of Contents Register 12: Register 13: Register 14: Register 15: Register 16: I2C Slave Data (I2CSDR), offset 0x808 ........................................................................... I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C ........................................................... I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 ................................................... I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 .............................................. I2C Slave Interrupt Clear (I2CSICR), offset 0x818 ............................................................ 433 434 435 436 437 Analog Comparators ................................................................................................................... 438 Register 1: Register 2: Register 3: Register 4: Register 5: Register 6: Register 7: Register 8: Register 9: Register 10: Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 .................................. Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 ....................................... Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 ......................................... Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 ....................... Analog Comparator Status 0 (ACSTAT0), offset 0x020 ..................................................... Analog Comparator Status 1 (ACSTAT1), offset 0x040 ..................................................... Analog Comparator Status 2 (ACSTAT2), offset 0x060 ..................................................... Analog Comparator Control 0 (ACCTL0), offset 0x024 ..................................................... Analog Comparator Control 1 (ACCTL1), offset 0x044 ..................................................... Analog Comparator Control 2 (ACCTL2), offset 0x064 .................................................... 18 444 445 446 447 448 448 448 449 449 449 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Revision History The revision history table notes changes made between the indicated revisions of the LM3S600 data sheet. Table 1. Revision History Date July 2014 June 2012 November 2011 Revision Description 15852.2743 ■ ■ In UART chapter: – Clarified that the transmit interrupt is based on a transition through level. – Corrected reset for UART Raw Interrupt Status (UARTRIS) register. ■ In Ordering and Contact Information appendix, moved orderable part numbers table to addendum. ■ Additional minor data sheet clarifications and corrections. 12739.2515 ■ 11107 In Internal Memory chapter, added sections on Execute-Only Protection, Read-Only Protection, and Permanently Disabling Debug. In Reset Characteristics table, changed values and units for Internal reset timeout after hardware reset (R7). ■ Removed 48QFN package. ■ Minor data sheet clarifications and corrections. ■ Added module-specific pin tables to each chapter in the new Signal Description sections. ■ In Timer chapter, clarified that in 16-Bit Input Edge Time Mode, the timer is capable of capturing three types of events: rising edge, falling edge, or both. ■ In UART chapter, clarified interrupt behavior. ■ In SSI chapter, corrected SSIClk in the figure "Synchronous Serial Frame Format (Single Transfer)". ■ In Signal Tables chapter: – ■ ■ Corrected pin numbers in table "Connections for Unused Signals" (other pin tables were correct). In Electrical Characteristics chapter: – Added parameter "Input voltage for a GPIO configured as an analog input" to the "Maximum Ratings" table. – Corrected Nom values for parameters "TCK clock Low time" and "TCK clock High time" in "JTAG Characteristics" table. Additional minor data sheet clarifications and corrections. July 14, 2014 19 Texas Instruments-Production Data Revision History Table 1. Revision History (continued) Date Revision January 2011 9102 September 2010 June 2010 7783 7393 Description ■ In Application Interrupt and Reset Control (APINT) register, changed bit name from SYSRESETREQ to SYSRESREQ. ■ Added DEBUG (Debug Priority) bit field to System Handler Priority 3 (SYSPRI3) register. ■ Added "Reset Sources" table to System Control chapter. ■ Removed mention of false-start bit detection in the UART chapter. This feature is not supported. ■ Added note that specific module clocks must be enabled before that module's registers can be programmed. There must be a delay of 3 system clocks after the module clock is enabled before any of that module's registers are accessed. ■ Changed I2C slave register base addresses and offsets to be relative to the I2C module base address of 0x4002.0000 , so register bases and offsets were changed for all I2C slave registers. Note that ® the hw_i2c.h file in the StellarisWare Driver Library uses a base address of 0x4002.0800 for the 2 I C slave registers. Be aware when using registers with offsets between 0x800 and 0x818 that StellarisWare uses the old slave base address for these offsets. ■ Added specification for maximum input voltage on a non-power pin when the microcontroller is unpowered (VNON parameter in Maximum Ratings table). ■ Additional minor data sheet clarifications and corrections. ■ Reorganized ARM Cortex-M3 Processor Core, Memory Map and Interrupts chapters, creating two new chapters, The Cortex-M3 Processor and Cortex-M3 Peripherals. Much additional content was added, including all the Cortex-M3 registers. ■ Changed register names to be consistent with StellarisWare names: the Cortex-M3 Interrupt Control and Status (ICSR) register to the Interrupt Control and State (INTCTRL) register, and the Cortex-M3 Interrupt Set Enable (SETNA) register to the Interrupt 0-31 Set Enable (EN0) register. ■ Added clarification of instruction execution during Flash operations. ■ Modified Figure 7-1 on page 226 to clarify operation of the GPIO inputs when used as an alternate function. ■ Added caution not to apply a Low value to PB7 when debugging; a Low value on the pin causes the JTAG controller to be reset, resulting in a loss of JTAG communication. ■ In General-Purpose Timers chapter, clarified operation of the 32-bit RTC mode. ■ Added missing table "Connections for Unused Signals" (Table 15-5 on page 459). ■ In Electrical Characteristics chapter: – Added ILKG parameter (GPIO input leakage current) to Table 17-4 on page 462. – Corrected values for tCLKRF parameter (SSIClk rise/fall time) in Table 17-13 on page 469. ■ Added dimensions for Tray and Tape and Reel shipping mediums. ■ Corrected base address for SRAM in architectural overview chapter. ■ Clarified system clock operation, adding content to “Clock Control” on page 155. ■ In Signal Tables chapter, added table "Connections for Unused Signals." ■ In "Reset Characteristics" table, corrected value for supply voltage (VDD) rise time. ■ Additional minor data sheet clarifications and corrections. 20 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 1. Revision History (continued) Date Revision April 2010 7004 January 2010 6712 Description ■ Added caution note to the I2C Master Timer Period (I2CMTPR) register description and changed field width to 7 bits. ■ Added note about RST signal routing. ■ Clarified the function of the TnSTALL bit in the GPTMCTL register. ■ Additional minor data sheet clarifications and corrections. ■ In "System Control" section, clarified Debug Access Port operation after Sleep modes. ■ Clarified wording on Flash memory access errors. ■ Added section on Flash interrupts. ■ Clarified operation of SSI transmit FIFO. ■ Made these changes to the Operating Characteristics chapter: ■ October 2009 July 2009 April 2009 6438 5953 5369 – Added storage temperature ratings to "Temperature Characteristics" table – Added "ESD Absolute Maximum Ratings" table Made these changes to the Electrical Characteristics chapter: – In "Flash Memory Characteristics" table, corrected Mass erase time – Added sleep and deep-sleep wake-up times ("Sleep Modes AC Characteristics" table) – In "Reset Characteristics" table, corrected supply voltage (VDD) rise time ■ The reset value for the DID1 register may change, depending on the package. ■ Deleted reset value for 16-bit mode from GPTMTAILR, GPTMTAMATCHR, and GPTMTAR registers because the module resets in 32-bit mode. ■ Made these changes to the Electrical Characteristics chapter: – Removed VSIH and VSIL parameters from Operating Conditions table. – Changed SSI set up and hold times to be expressed in system clocks, not ns. ■ Added 48QFN package. ■ Additional minor data sheet clarifications and corrections. ■ Clarified Power-on reset and RST pin operation; added new diagrams. ■ Added DBG bits missing from FMPRE register. This changes register reset value. ■ In ADC characteristics table, changed Max value for GAIN parameter from ±1 to ±3 and added EIR (Internal voltage reference error) parameter. ■ Corrected ordering numbers. ■ Additional minor data sheet clarifications and corrections. ■ Added JTAG/SWD clarification (see “Communication with JTAG/SWD” on page 145). ■ Added "GPIO Module DC Characteristics" table (see Table 17-4 on page 462). ■ Additional minor data sheet clarifications and corrections. July 14, 2014 21 Texas Instruments-Production Data Revision History Table 1. Revision History (continued) Date Revision January 2009 4644 November 2008 October 2008 4283 4149 Description ■ Incorrect bit type for RELOAD bit field in SysTick Reload Value register; changed to R/W. ■ Clarification added as to what happens when the SSI in slave mode is required to transmit but there is no data in the TX FIFO. ■ Minor corrections to comparator operating mode tables. ■ Additional minor data sheet clarifications and corrections. ■ Revised High-Level Block Diagram. ■ Corrected descriptions for UART1 signals. ■ Additional minor data sheet clarifications and corrections were made. ■ Added note on clearing interrupts to the Interrupts chapter: Note: June 2008 2972 It may take several processor cycles after a write to clear an interrupt source in order for NVIC to see the interrupt source de-assert. This means if the interrupt clear is done as the last action in an interrupt handler, it is possible for the interrupt handler to complete while NVIC sees the interrupt as still asserted, causing the interrupt handler to be re-entered errantly. This can be avoided by either clearing the interrupt source at the beginning of the interrupt handler or by performing a read or write after the write to clear the interrupt source (and flush the write buffer) ■ Bit 13 and bit 5 of the GPTM Control (GPTMCTL) register should have been marked as reserved ® for Stellaris devices without an ADC module. ■ Additional minor data sheet clarifications and corrections were made. Started tracking revision history. 22 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller About This Document This data sheet provides reference information for the LM3S600 microcontroller, describing the functional blocks of the system-on-chip (SoC) device designed around the ARM® Cortex™-M3 core. Audience This manual is intended for system software developers, hardware designers, and application developers. About This Manual This document is organized into sections that correspond to each major feature. Related Documents ® The following related documents are available on the Stellaris web site at www.ti.com/stellaris: ■ Stellaris® Errata ■ ARM® Cortex™-M3 Errata ■ Cortex™-M3/M4 Instruction Set Technical User's Manual ■ Stellaris® Graphics Library User's Guide ■ Stellaris® Peripheral Driver Library User's Guide The following related documents are also referenced: ■ ARM® Debug Interface V5 Architecture Specification ■ ARM® Embedded Trace Macrocell Architecture Specification ■ IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture This documentation list was current as of publication date. Please check the web site for additional documentation, including application notes and white papers. July 14, 2014 23 Texas Instruments-Production Data About This Document Documentation Conventions This document uses the conventions shown in Table 2 on page 24. Table 2. Documentation Conventions Notation Meaning General Register Notation REGISTER APB registers are indicated in uppercase bold. For example, PBORCTL is the Power-On and Brown-Out Reset Control register. If a register name contains a lowercase n, it represents more than one register. For example, SRCRn represents any (or all) of the three Software Reset Control registers: SRCR0, SRCR1 , and SRCR2. bit A single bit in a register. bit field Two or more consecutive and related bits. offset 0xnnn A hexadecimal increment to a register's address, relative to that module's base address as specified in Table 2-4 on page 59. Register N Registers are numbered consecutively throughout the document to aid in referencing them. The register number has no meaning to software. reserved Register bits marked reserved are reserved for future use. In most cases, reserved bits are set to 0; however, user software should not rely on the value of a reserved bit. To provide software compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. yy:xx The range of register bits inclusive from xx to yy. For example, 31:15 means bits 15 through 31 in that register. Register Bit/Field Types This value in the register bit diagram indicates whether software running on the controller can change the value of the bit field. RC Software can read this field. The bit or field is cleared by hardware after reading the bit/field. RO Software can read this field. Always write the chip reset value. R/W Software can read or write this field. R/WC Software can read or write this field. Writing to it with any value clears the register. R/W1C Software can read or write this field. A write of a 0 to a W1C bit does not affect the bit value in the register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. This register type is primarily used for clearing interrupt status bits where the read operation provides the interrupt status and the write of the read value clears only the interrupts being reported at the time the register was read. R/W1S Software can read or write a 1 to this field. A write of a 0 to a R/W1S bit does not affect the bit value in the register. W1C Software can write this field. A write of a 0 to a W1C bit does not affect the bit value in the register. A write of a 1 clears the value of the bit in the register; the remaining bits remain unchanged. A read of the register returns no meaningful data. This register is typically used to clear the corresponding bit in an interrupt register. WO Only a write by software is valid; a read of the register returns no meaningful data. Register Bit/Field Reset Value This value in the register bit diagram shows the bit/field value after any reset, unless noted. 0 Bit cleared to 0 on chip reset. 1 Bit set to 1 on chip reset. - Nondeterministic. Pin/Signal Notation [] Pin alternate function; a pin defaults to the signal without the brackets. pin Refers to the physical connection on the package. signal Refers to the electrical signal encoding of a pin. 24 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 2. Documentation Conventions (continued) Notation Meaning assert a signal Change the value of the signal from the logically False state to the logically True state. For active High signals, the asserted signal value is 1 (High); for active Low signals, the asserted signal value is 0 (Low). The active polarity (High or Low) is defined by the signal name (see SIGNAL and SIGNAL below). deassert a signal Change the value of the signal from the logically True state to the logically False state. SIGNAL Signal names are in uppercase and in the Courier font. An overbar on a signal name indicates that it is active Low. To assert SIGNAL is to drive it Low; to deassert SIGNAL is to drive it High. SIGNAL Signal names are in uppercase and in the Courier font. An active High signal has no overbar. To assert SIGNAL is to drive it High; to deassert SIGNAL is to drive it Low. Numbers X An uppercase X indicates any of several values is allowed, where X can be any legal pattern. For example, a binary value of 0X00 can be either 0100 or 0000, a hex value of 0xX is 0x0 or 0x1, and so on. 0x Hexadecimal numbers have a prefix of 0x. For example, 0x00FF is the hexadecimal number FF. All other numbers within register tables are assumed to be binary. Within conceptual information, binary numbers are indicated with a b suffix, for example, 1011b, and decimal numbers are written without a prefix or suffix. July 14, 2014 25 Texas Instruments-Production Data Architectural Overview 1 Architectural Overview ® The Stellaris family of microcontrollers—the first ARM® Cortex™-M3 based controllers—brings high-performance 32-bit computing to cost-sensitive embedded microcontroller applications. These pioneering parts deliver customers 32-bit performance at a cost equivalent to legacy 8- and 16-bit devices, all in a package with a small footprint. The LM3S600 microcontroller is targeted for industrial applications, including test and measurement equipment, factory automation, HVAC and building control, motion control, medical instrumentation, fire and security, and power/energy. In addition, the LM3S600 microcontroller offers the advantages of ARM's widely available development tools, System-on-Chip (SoC) infrastructure IP applications, and a large user community. Additionally, the microcontroller uses ARM's Thumb®-compatible Thumb-2 instruction set to reduce memory requirements and, thereby, cost. Finally, the LM3S600 microcontroller is code-compatible to all members of the extensive Stellaris family; providing flexibility to fit our customers' precise needs. Texas Instruments offers a complete solution to get to market quickly, with evaluation and development boards, white papers and application notes, an easy-to-use peripheral driver library, and a strong support, sales, and distributor network. See “Ordering and Contact Information” on page 493 for ordering information for Stellaris family devices. 1.1 Product Features The LM3S600 microcontroller includes the following product features: ■ 32-Bit RISC Performance – 32-bit ARM® Cortex™-M3 v7M architecture optimized for small-footprint embedded applications – System timer (SysTick), providing a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism – Thumb®-compatible Thumb-2-only instruction set processor core for high code density – 50-MHz operation – Hardware-division and single-cycle-multiplication – Integrated Nested Vectored Interrupt Controller (NVIC) providing deterministic interrupt handling – 21 interrupts with eight priority levels – Memory protection unit (MPU), providing a privileged mode for protected operating system functionality – Unaligned data access, enabling data to be efficiently packed into memory – Atomic bit manipulation (bit-banding), delivering maximum memory utilization and streamlined peripheral control ■ ARM® Cortex™-M3 Processor Core 26 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller – Compact core. – Thumb-2 instruction set, delivering the high-performance expected of an ARM core in the memory size usually associated with 8- and 16-bit devices; typically in the range of a few kilobytes of memory for microcontroller class applications. – Rapid application execution through Harvard architecture characterized by separate buses for instruction and data. – Exceptional interrupt handling, by implementing the register manipulations required for handling an interrupt in hardware. – Deterministic, fast interrupt processing: always 12 cycles, or just 6 cycles with tail-chaining – Memory protection unit (MPU) to provide a privileged mode of operation for complex applications. – Migration from the ARM7™ processor family for better performance and power efficiency. – Full-featured debug solution • Serial Wire JTAG Debug Port (SWJ-DP) • Flash Patch and Breakpoint (FPB) unit for implementing breakpoints • Data Watchpoint and Trigger (DWT) unit for implementing watchpoints, trigger resources, and system profiling • Instrumentation Trace Macrocell (ITM) for support of printf style debugging • Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer – Optimized for single-cycle flash usage – Three sleep modes with clock gating for low power – Single-cycle multiply instruction and hardware divide – Atomic operations – ARM Thumb2 mixed 16-/32-bit instruction set – 1.25 DMIPS/MHz ■ JTAG – IEEE 1149.1-1990 compatible Test Access Port (TAP) controller – Four-bit Instruction Register (IR) chain for storing JTAG instructions – IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, EXTEST and INTEST – ARM additional instructions: APACC, DPACC and ABORT – Integrated ARM Serial Wire Debug (SWD) July 14, 2014 27 Texas Instruments-Production Data Architectural Overview ■ Internal Memory – 32 KB single-cycle flash • User-managed flash block protection on a 2-KB block basis • User-managed flash data programming • User-defined and managed flash-protection block – 8 KB single-cycle SRAM ■ GPIOs – 8-36 GPIOs, depending on configuration – 5-V-tolerant in input configuration – Fast toggle capable of a change every two clock cycles – Programmable control for GPIO interrupts • Interrupt generation masking • Edge-triggered on rising, falling, or both • Level-sensitive on High or Low values – Bit masking in both read and write operations through address lines – Pins configured as digital inputs are Schmitt-triggered. – Programmable control for GPIO pad configuration • Weak pull-up or pull-down resistors • 2-mA, 4-mA, and 8-mA pad drive for digital communication • Slew rate control for the 8-mA drive • Open drain enables • Digital input enables ■ General-Purpose Timers – Three General-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/counters. Each GPTM can be configured to operate independently: • As a single 32-bit timer • As one 32-bit Real-Time Clock (RTC) to event capture • For Pulse Width Modulation (PWM) – 32-bit Timer modes 28 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller • Programmable one-shot timer • Programmable periodic timer • Real-Time Clock when using an external 32.768-KHz clock as the input • User-enabled stalling when the controller asserts CPU Halt flag during debug – 16-bit Timer modes • General-purpose timer function with an 8-bit prescaler (for one-shot and periodic modes only) • Programmable one-shot timer • Programmable periodic timer • User-enabled stalling when the controller asserts CPU Halt flag during debug – 16-bit Input Capture modes • Input edge count capture • Input edge time capture – 16-bit PWM mode • Simple PWM mode with software-programmable output inversion of the PWM signal ■ ARM FiRM-compliant Watchdog Timer – 32-bit down counter with a programmable load register – Separate watchdog clock with an enable – Programmable interrupt generation logic with interrupt masking – Lock register protection from runaway software – Reset generation logic with an enable/disable – User-enabled stalling when the controller asserts the CPU Halt flag during debug ■ UART – Two fully programmable 16C550-type UARTs – Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading – Programmable baud-rate generator allowing speeds up to 3.125 Mbps – Programmable FIFO length, including 1-byte deep operation providing conventional double-buffered interface – FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8 – Standard asynchronous communication bits for start, stop, and parity July 14, 2014 29 Texas Instruments-Production Data Architectural Overview – Line-break generation and detection – Fully programmable serial interface characteristics • 5, 6, 7, or 8 data bits • Even, odd, stick, or no-parity bit generation/detection • 1 or 2 stop bit generation ■ Synchronous Serial Interface (SSI) – Master or slave operation – Programmable clock bit rate and prescale – Separate transmit and receive FIFOs, 16 bits wide, 8 locations deep – Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces – Programmable data frame size from 4 to 16 bits – Internal loopback test mode for diagnostic/debug testing ■ I2C – Devices on the I2C bus can be designated as either a master or a slave • Supports both sending and receiving data as either a master or a slave • Supports simultaneous master and slave operation – Four I2C modes • Master transmit • Master receive • Slave transmit • Slave receive – Two transmission speeds: Standard (100 Kbps) and Fast (400 Kbps) – Master and slave interrupt generation • Master generates interrupts when a transmit or receive operation completes (or aborts due to an error) • Slave generates interrupts when data has been sent or requested by a master – Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode ■ Analog Comparators 30 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller – Three independent integrated analog comparators – Configurable for output to drive an output pin or generate an interrupt – Compare external pin input to external pin input or to internal programmable voltage reference – Compare a test voltage against any one of these voltages • An individual external reference voltage • A shared single external reference voltage • A shared internal reference voltage ■ Power – On-chip Low Drop-Out (LDO) voltage regulator, with programmable output user-adjustable from 2.25 V to 2.75 V – Low-power options on controller: Sleep and Deep-sleep modes – Low-power options for peripherals: software controls shutdown of individual peripherals – User-enabled LDO unregulated voltage detection and automatic reset – 3.3-V supply brown-out detection and reporting via interrupt or reset ■ Flexible Reset Sources – Power-on reset (POR) – Reset pin assertion – Brown-out (BOR) detector alerts to system power drops – Software reset – Watchdog timer reset – Internal low drop-out (LDO) regulator output goes unregulated ■ Industrial and extended temperature 48-pin RoHS-compliant LQFP package 1.2 Target Applications ■ Factory automation and control ■ Industrial control power devices ■ Building and home automation ■ Stepper motors ■ Brushless DC motors ■ AC induction motors July 14, 2014 31 Texas Instruments-Production Data Architectural Overview 1.3 High-Level Block Diagram Figure 1-1 on page 33 depicts the features on the Stellaris LM3S600 microcontroller. 32 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 1-1. Stellaris LM3S600 Microcontroller High-Level Block Diagram JTAG/SWD ARM® Cortex™-M3 (50MHz) System Control and Clocks (w/ Precis. Osc.) Flash (32KB) DCode bus NVIC MPU ICode bus System Bus LM3S600 Bus Matrix SRAM (8KB) SYSTEM PERIPHERALS I2C (1) Watchdog Timer (1) Advanced Peripheral Bus (APB) GeneralPurpose Timer (3) GPIOs (8-36) SERIAL PERIPHERALS UART (2) SSI (1) ANALOG PERIPHERALS Analog Comparator (3) July 14, 2014 33 Texas Instruments-Production Data Architectural Overview 1.4 Functional Overview The following sections provide an overview of the features of the LM3S600 microcontroller. The page number in parenthesis indicates where that feature is discussed in detail. Ordering and support information can be found in “Ordering and Contact Information” on page 493. 1.4.1 ARM Cortex™-M3 1.4.1.1 Processor Core (see page 40) All members of the Stellaris product family, including the LM3S600 microcontroller, are designed around an ARM Cortex™-M3 processor core. The ARM Cortex-M3 processor provides the core for a high-performance, low-cost platform that meets the needs of minimal memory implementation, reduced pin count, and low-power consumption, while delivering outstanding computational performance and exceptional system response to interrupts. 1.4.1.2 Memory Map (see page 59) A memory map lists the location of instructions and data in memory. The memory map for the LM3S600 controller can be found in Table 2-4 on page 59. Register addresses are given as a hexadecimal increment, relative to the module's base address as shown in the memory map. 1.4.1.3 System Timer (SysTick) (see page 82) Cortex-M3 includes an integrated system timer, SysTick. SysTick provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter can be used in several different ways, for example: ■ An RTOS tick timer which fires at a programmable rate (for example, 100 Hz) and invokes a SysTick routine. ■ A high-speed alarm timer using the system clock. ■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock used and the dynamic range of the counter. ■ A simple counter. Software can use this to measure time to completion and time used. ■ An internal clock source control based on missing/meeting durations. The COUNTFLAG bit-field in the control and status register can be used to determine if an action completed within a set duration, as part of a dynamic clock management control loop. 1.4.1.4 Nested Vectored Interrupt Controller (NVIC) (see page 83) The LM3S600 controller includes the ARM Nested Vectored Interrupt Controller (NVIC) on the ARM® Cortex™-M3 core. The NVIC and Cortex-M3 prioritize and handle all exceptions. All exceptions are handled in Handler Mode. The processor state is automatically stored to the stack on an exception, and automatically restored from the stack at the end of the Interrupt Service Routine (ISR). The vector is fetched in parallel to the state saving, which enables efficient interrupt entry. The processor supports tail-chaining, which enables back-to-back interrupts to be performed without the overhead of state saving and restoration. Software can set eight priority levels on 7 exceptions (system handlers) and 21 interrupts. 34 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 1.4.1.5 System Control Block (SCB) (see page 85) The SCB provides system implementation information and system control, including configuration, control, and reporting of system exceptions. 1.4.1.6 Memory Protection Unit (MPU) (see page 85) The MPU supports the standard ARMv7 Protected Memory System Architecture (PMSA) model. The MPU provides full support for protection regions, overlapping protection regions, access permissions, and exporting memory attributes to the system. 1.4.2 Motor Control Peripherals To enhance motor control, the LM3S600 controller features Pulse Width Modulation (PWM) outputs. 1.4.2.1 PWM Pulse width modulation (PWM) is a powerful technique for digitally encoding analog signal levels. High-resolution counters are used to generate a square wave, and the duty cycle of the square wave is modulated to encode an analog signal. Typical applications include switching power supplies and motor control. On the LM3S600, PWM motion control functionality can be achieved through: ■ The motion control features of the general-purpose timers using the CCP pins CCP Pins (see page 269) The General-Purpose Timer Module's CCP (Capture Compare PWM) pins are software programmable to support a simple PWM mode with a software-programmable output inversion of the PWM signal. 1.4.3 Analog Peripherals For support of analog signals, the LM3S600 microcontroller offers three analog comparators. 1.4.3.1 Analog Comparators (see page 438) An analog comparator is a peripheral that compares two analog voltages, and provides a logical output that signals the comparison result. The LM3S600 microcontroller provides three independent integrated analog comparators that can be configured to drive an output or generate an interrupt . A comparator can compare a test voltage against any one of these voltages: ■ An individual external reference voltage ■ A shared single external reference voltage ■ A shared internal reference voltage The comparator can provide its output to a device pin, acting as a replacement for an analog comparator on the board, or it can be used to signal the application via interrupts to cause it to start capturing a sample sequence. 1.4.4 Serial Communications Peripherals The LM3S600 controller supports both asynchronous and synchronous serial communications with: July 14, 2014 35 Texas Instruments-Production Data Architectural Overview ■ Two fully programmable 16C550-type UARTs ■ One SSI module ■ One I2C module 1.4.4.1 UART (see page 323) A Universal Asynchronous Receiver/Transmitter (UART) is an integrated circuit used for RS-232C serial communications, containing a transmitter (parallel-to-serial converter) and a receiver (serial-to-parallel converter), each clocked separately. The LM3S600 controller includes two fully programmable 16C550-type UARTs that support data transfer speeds up to 3.125 Mbps. (Although similar in functionality to a 16C550 UART, it is not register-compatible.) Separate 16x8 transmit (TX) and receive (RX) FIFOs reduce CPU interrupt service loading. The UART can generate individually masked interrupts from the RX, TX, modem status, and error conditions. The module provides a single combined interrupt when any of the interrupts are asserted and are unmasked. 1.4.4.2 SSI (see page 363) Synchronous Serial Interface (SSI) is a four-wire bi-directional full and low-speed communications interface. The LM3S600 controller includes one SSI module that provides the functionality for synchronous serial communications with peripheral devices, and can be configured to use the Freescale SPI, MICROWIRE, or TI synchronous serial interface frame formats. The size of the data frame is also configurable, and can be set between 4 and 16 bits, inclusive. The SSI module performs serial-to-parallel conversion on data received from a peripheral device, and parallel-to-serial conversion on data transmitted to a peripheral device. The TX and RX paths are buffered with internal FIFOs, allowing up to eight 16-bit values to be stored independently. The SSI module can be configured as either a master or slave device. As a slave device, the SSI module can also be configured to disable its output, which allows a master device to be coupled with multiple slave devices. The SSI module also includes a programmable bit rate clock divider and prescaler to generate the output serial clock derived from the SSI module's input clock. Bit rates are generated based on the input clock and the maximum bit rate is determined by the connected peripheral. 1.4.4.3 I2C (see page 401) The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design (a serial data line SDA and a serial clock line SCL). The I2C bus interfaces to external I2C devices such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on. The I2C bus may also be used for system testing and diagnostic purposes in product development and manufacture. The LM3S600 controller includes one I2C module that provides the ability to communicate to other IC devices over an I2C bus. The I2C bus supports devices that can both transmit and receive (write and read) data. Devices on the I2C bus can be designated as either a master or a slave. The I2C module supports both sending and receiving data as either a master or a slave, and also supports the simultaneous 36 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller operation as both a master and a slave. The four I2C modes are: Master Transmit, Master Receive, Slave Transmit, and Slave Receive. A Stellaris I2C module can operate at two speeds: Standard (100 Kbps) and Fast (400 Kbps). Both the I2C master and slave can generate interrupts. The I2C master generates interrupts when a transmit or receive operation completes (or aborts due to an error). The I2C slave generates interrupts when data has been sent or requested by a master. 1.4.5 System Peripherals 1.4.5.1 Programmable GPIOs (see page 223) General-purpose input/output (GPIO) pins offer flexibility for a variety of connections. The Stellaris GPIO module is comprised of five physical GPIO blocks, each corresponding to an individual GPIO port. The GPIO module is FiRM-compliant (compliant to the ARM Foundation IP for Real-Time Microcontrollers specification) and supports 8-36 programmable input/output pins. The number of GPIOs available depends on the peripherals being used (see “Signal Tables” on page 452 for the signals available to each GPIO pin). The GPIO module features programmable interrupt generation as either edge-triggered or level-sensitive on all pins, programmable control for GPIO pad configuration, and bit masking in both read and write operations through address lines. Pins configured as digital inputs are Schmitt-triggered. 1.4.5.2 Three Programmable Timers (see page 263) Programmable timers can be used to count or time external events that drive the Timer input pins. The Stellaris General-Purpose Timer Module (GPTM) contains three GPTM blocks. Each GPTM block provides two 16-bit timers/counters that can be configured to operate independently as timers or event counters, or configured to operate as one 32-bit timer or one 32-bit Real-Time Clock (RTC). When configured in 32-bit mode, a timer can run as a Real-Time Clock (RTC), one-shot timer or periodic timer. When in 16-bit mode, a timer can run as a one-shot timer or periodic timer, and can extend its precision by using an 8-bit prescaler. A 16-bit timer can also be configured for event capture or Pulse Width Modulation (PWM) generation. 1.4.5.3 Watchdog Timer (see page 299) A watchdog timer can generate an interrupt or a reset when a time-out value is reached. The watchdog timer is used to regain control when a system has failed due to a software error or to the failure of an external device to respond in the expected way. The Stellaris Watchdog Timer module consists of a 32-bit down counter, a programmable load register, interrupt generation logic, and a locking register. The Watchdog Timer can be configured to generate an interrupt to the controller on its first time-out, and to generate a reset signal on its second time-out. Once the Watchdog Timer has been configured, the lock register can be written to prevent the timer configuration from being inadvertently altered. 1.4.6 Memory Peripherals The LM3S600 controller offers both single-cycle SRAM and single-cycle Flash memory. July 14, 2014 37 Texas Instruments-Production Data Architectural Overview 1.4.6.1 SRAM (see page 205) The LM3S600 static random access memory (SRAM) controller supports 8 KB SRAM. The internal SRAM of the Stellaris devices starts at base address 0x2000.0000 of the device memory map. To reduce the number of time-consuming read-modify-write (RMW) operations, ARM has introduced bit-banding technology in the new Cortex-M3 processor. With a bit-band-enabled processor, certain regions in the memory map (SRAM and peripheral space) can use address aliases to access individual bits in a single, atomic operation. 1.4.6.2 Flash (see page 206) The LM3S600 Flash controller supports 32 KB of flash memory. The flash is organized as a set of 1-KB blocks that can be individually erased. Erasing a block causes the entire contents of the block to be reset to all 1s. These blocks are paired into a set of 2-KB blocks that can be individually protected. The blocks can be marked as read-only or execute-only, providing different levels of code protection. Read-only blocks cannot be erased or programmed, protecting the contents of those blocks from being modified. Execute-only blocks cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism, protecting the contents of those blocks from being read by either the controller or by a debugger. 1.4.7 Additional Features 1.4.7.1 JTAG TAP Controller (see page 140) The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR) can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing information on the components. The JTAG Port also provides a means of accessing and controlling design-for-test features such as I/O pin observation and control, scan testing, and debugging. The JTAG port is composed of the standard five pins: TRST, TCK, TMS, TDI, and TDO. Data is transmitted serially into the controller on TDI and out of the controller on TDO. The interpretation of this data is dependent on the current state of the TAP controller. For detailed information on the operation of the JTAG port and TAP controller, please refer to the IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture. The Stellaris JTAG controller works with the ARM JTAG controller built into the Cortex-M3 core. This is implemented by multiplexing the TDO outputs from both JTAG controllers. ARM JTAG instructions select the ARM TDO output while Stellaris JTAG instructions select the Stellaris TDO outputs. The multiplexer is controlled by the Stellaris JTAG controller, which has comprehensive programming for the ARM, Stellaris, and unimplemented JTAG instructions. 1.4.7.2 System Control and Clocks (see page 150) System control determines the overall operation of the device. It provides information about the device, controls the clocking of the device and individual peripherals, and handles reset detection and reporting. 1.4.8 Hardware Details Details on the pins and package can be found in the following sections: ■ “Pin Diagram” on page 451 ■ “Signal Tables” on page 452 38 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ “Operating Characteristics” on page 460 ■ “Electrical Characteristics” on page 461 ■ “Package Information” on page 495 July 14, 2014 39 Texas Instruments-Production Data The Cortex-M3 Processor 2 The Cortex-M3 Processor The ARM® Cortex™-M3 processor provides a high-performance, low-cost platform that meets the system requirements of minimal memory implementation, reduced pin count, and low power consumption, while delivering outstanding computational performance and exceptional system response to interrupts. Features include: ■ Compact core. ■ Thumb-2 instruction set, delivering the high-performance expected of an ARM core in the memory size usually associated with 8- and 16-bit devices; typically in the range of a few kilobytes of memory for microcontroller class applications. ■ Rapid application execution through Harvard architecture characterized by separate buses for instruction and data. ■ Exceptional interrupt handling, by implementing the register manipulations required for handling an interrupt in hardware. ■ Deterministic, fast interrupt processing: always 12 cycles, or just 6 cycles with tail-chaining ■ Memory protection unit (MPU) to provide a privileged mode of operation for complex applications. ■ Migration from the ARM7™ processor family for better performance and power efficiency. ■ Full-featured debug solution – Serial Wire JTAG Debug Port (SWJ-DP) – Flash Patch and Breakpoint (FPB) unit for implementing breakpoints – Data Watchpoint and Trigger (DWT) unit for implementing watchpoints, trigger resources, and system profiling – Instrumentation Trace Macrocell (ITM) for support of printf style debugging – Trace Port Interface Unit (TPIU) for bridging to a Trace Port Analyzer ■ Optimized for single-cycle flash usage ■ Three sleep modes with clock gating for low power ■ Single-cycle multiply instruction and hardware divide ■ Atomic operations ■ ARM Thumb2 mixed 16-/32-bit instruction set ■ 1.25 DMIPS/MHz ® The Stellaris family of microcontrollers builds on this core to bring high-performance 32-bit computing to cost-sensitive embedded microcontroller applications, such as factory automation and control, industrial control power devices, building and home automation, and stepper motor control. 40 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller This chapter provides information on the Stellaris implementation of the Cortex-M3 processor, including the programming model, the memory model, the exception model, fault handling, and power management. For technical details on the instruction set, see the Cortex™-M3/M4 Instruction Set Technical User's Manual. 2.1 Block Diagram The Cortex-M3 processor is built on a high-performance processor core, with a 3-stage pipeline Harvard architecture, making it ideal for demanding embedded applications. The processor delivers exceptional power efficiency through an efficient instruction set and extensively optimized design, providing high-end processing hardware including a range of single-cycle and SIMD multiplication and multiply-with-accumulate capabilities, saturating arithmetic and dedicated hardware division. To facilitate the design of cost-sensitive devices, the Cortex-M3 processor implements tightly coupled system components that reduce processor area while significantly improving interrupt handling and system debug capabilities. The Cortex-M3 processor implements a version of the Thumb® instruction set based on Thumb-2 technology, ensuring high code density and reduced program memory requirements. The Cortex-M3 instruction set provides the exceptional performance expected of a modern 32-bit architecture, with the high code density of 8-bit and 16-bit microcontrollers. The Cortex-M3 processor closely integrates a nested interrupt controller (NVIC), to deliver industry-leading interrupt performance. The Stellaris NVIC includes a non-maskable interrupt (NMI) and provides eight interrupt priority levels. The tight integration of the processor core and NVIC provides fast execution of interrupt service routines (ISRs), dramatically reducing interrupt latency. The hardware stacking of registers and the ability to suspend load-multiple and store-multiple operations further reduce interrupt latency. Interrupt handlers do not require any assembler stubs which removes code overhead from the ISRs. Tail-chaining optimization also significantly reduces the overhead when switching from one ISR to another. To optimize low-power designs, the NVIC integrates with the sleep modes, including Deep-sleep mode, which enables the entire device to be rapidly powered down. July 14, 2014 41 Texas Instruments-Production Data The Cortex-M3 Processor Figure 2-1. CPU Block Diagram Nested Vectored Interrupt Controller Interrupts Sleep ARM Cortex-M3 CM3 Core Debug Instructions Data Trace Port Interface Unit Memory Protection Unit Flash Patch and Breakpoint Instrumentation Data Watchpoint Trace Macrocell and Trace ROM Table Private Peripheral Bus (internal) Adv. Peripheral Bus Bus Matrix Serial Wire JTAG Debug Port Debug Access Port 2.2 Overview 2.2.1 System-Level Interface Serial Wire Output Trace Port (SWO) I-code bus D-code bus System bus The Cortex-M3 processor provides multiple interfaces using AMBA® technology to provide high-speed, low-latency memory accesses. The core supports unaligned data accesses and implements atomic bit manipulation that enables faster peripheral controls, system spinlocks, and thread-safe Boolean data handling. The Cortex-M3 processor has a memory protection unit (MPU) that provides fine-grain memory control, enabling applications to implement security privilege levels and separate code, data and stack on a task-by-task basis. 2.2.2 Integrated Configurable Debug The Cortex-M3 processor implements a complete hardware debug solution, providing high system visibility of the processor and memory through either a traditional JTAG port or a 2-pin Serial Wire Debug (SWD) port that is ideal for microcontrollers and other small package devices. The Stellaris implementation replaces the ARM SW-DP and JTAG-DP with the ARM CoreSight™-compliant Serial Wire JTAG Debug Port (SWJ-DP) interface. The SWJ-DP interface combines the SWD and JTAG debug ports into one module. See the ARM® Debug Interface V5 Architecture Specification for details on SWJ-DP. For system trace, the processor integrates an Instrumentation Trace Macrocell (ITM) alongside data watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system trace events, a Serial Wire Viewer (SWV) can export a stream of software-generated messages, data trace, and profiling information through a single pin. 42 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller The Flash Patch and Breakpoint Unit (FPB) provides up to eight hardware breakpoint comparators that debuggers can use. The comparators in the FPB also provide remap functions of up to eight words in the program code in the CODE memory region. This enables applications stored in a read-only area of Flash memory to be patched in another area of on-chip SRAM or Flash memory. If a patch is required, the application programs the FPB to remap a number of addresses. When those addresses are accessed, the accesses are redirected to a remap table specified in the FPB configuration. For more information on the Cortex-M3 debug capabilities, see theARM® Debug Interface V5 Architecture Specification. 2.2.3 Trace Port Interface Unit (TPIU) The TPIU acts as a bridge between the Cortex-M3 trace data from the ITM, and an off-chip Trace Port Analyzer, as shown in Figure 2-2 on page 43. Figure 2-2. TPIU Block Diagram 2.2.4 Debug ATB Slave Port ATB Interface APB Slave Port APB Interface Asynchronous FIFO Trace Out (serializer) Serial Wire Trace Port (SWO) Cortex-M3 System Component Details The Cortex-M3 includes the following system components: ■ SysTick A 24-bit count-down timer that can be used as a Real-Time Operating System (RTOS) tick timer or as a simple counter (see “System Timer (SysTick)” on page 82). ■ Nested Vectored Interrupt Controller (NVIC) An embedded interrupt controller that supports low latency interrupt processing (see “Nested Vectored Interrupt Controller (NVIC)” on page 83). ■ System Control Block (SCB) July 14, 2014 43 Texas Instruments-Production Data The Cortex-M3 Processor The programming model interface to the processor. The SCB provides system implementation information and system control, including configuration, control, and reporting of system exceptions (see “System Control Block (SCB)” on page 85). ■ Memory Protection Unit (MPU) Improves system reliability by defining the memory attributes for different memory regions. The MPU provides up to eight different regions and an optional predefined background region (see “Memory Protection Unit (MPU)” on page 85). 2.3 Programming Model This section describes the Cortex-M3 programming model. In addition to the individual core register descriptions, information about the processor modes and privilege levels for software execution and stacks is included. 2.3.1 Processor Mode and Privilege Levels for Software Execution The Cortex-M3 has two modes of operation: ■ Thread mode Used to execute application software. The processor enters Thread mode when it comes out of reset. ■ Handler mode Used to handle exceptions. When the processor has finished exception processing, it returns to Thread mode. In addition, the Cortex-M3 has two privilege levels: ■ Unprivileged In this mode, software has the following restrictions: – Limited access to the MSR and MRS instructions and no use of the CPS instruction – No access to the system timer, NVIC, or system control block – Possibly restricted access to memory or peripherals ■ Privileged In this mode, software can use all the instructions and has access to all resources. In Thread mode, the CONTROL register (see page 58) controls whether software execution is privileged or unprivileged. In Handler mode, software execution is always privileged. Only privileged software can write to the CONTROL register to change the privilege level for software execution in Thread mode. Unprivileged software can use the SVC instruction to make a supervisor call to transfer control to privileged software. 2.3.2 Stacks The processor uses a full descending stack, meaning that the stack pointer indicates the last stacked item on the memory. When the processor pushes a new item onto the stack, it decrements the stack pointer and then writes the item to the new memory location. The processor implements two stacks: 44 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller the main stack and the process stack, with a pointer for each held in independent registers (see the SP register on page 48). In Thread mode, the CONTROL register (see page 58) controls whether the processor uses the main stack or the process stack. In Handler mode, the processor always uses the main stack. The options for processor operations are shown in Table 2-1 on page 45. Table 2-1. Summary of Processor Mode, Privilege Level, and Stack Use Processor Mode Use Privilege Level Thread Applications Privileged or unprivileged Stack Used Handler Exception handlers Always privileged a Main stack or process stack a Main stack a. See CONTROL (page 58). 2.3.3 Register Map Figure 2-3 on page 45 shows the Cortex-M3 register set. Table 2-2 on page 46 lists the Core registers. The core registers are not memory mapped and are accessed by register name, so the base address is n/a (not applicable) and there is no offset. Figure 2-3. Cortex-M3 Register Set R0 R1 R2 Low registers R3 R4 R5 R6 General-purpose registers R7 R8 R9 High registers R10 R11 R12 Stack Pointer SP (R13) Link Register LR (R14) Program Counter PC (R15) PSR PSP‡ MSP‡ ‡ Banked version of SP Program status register PRIMASK FAULTMASK Exception mask registers Special registers BASEPRI CONTROL CONTROL register July 14, 2014 45 Texas Instruments-Production Data The Cortex-M3 Processor Table 2-2. Processor Register Map Offset Type Reset - R0 R/W - Cortex General-Purpose Register 0 47 - R1 R/W - Cortex General-Purpose Register 1 47 - R2 R/W - Cortex General-Purpose Register 2 47 - R3 R/W - Cortex General-Purpose Register 3 47 - R4 R/W - Cortex General-Purpose Register 4 47 - R5 R/W - Cortex General-Purpose Register 5 47 - R6 R/W - Cortex General-Purpose Register 6 47 - R7 R/W - Cortex General-Purpose Register 7 47 - R8 R/W - Cortex General-Purpose Register 8 47 - R9 R/W - Cortex General-Purpose Register 9 47 - R10 R/W - Cortex General-Purpose Register 10 47 - R11 R/W - Cortex General-Purpose Register 11 47 - R12 R/W - Cortex General-Purpose Register 12 47 - SP R/W - Stack Pointer 48 - LR R/W 0xFFFF.FFFF Link Register 49 - PC R/W - Program Counter 50 - PSR R/W 0x0100.0000 Program Status Register 51 - PRIMASK R/W 0x0000.0000 Priority Mask Register 55 - FAULTMASK R/W 0x0000.0000 Fault Mask Register 56 - BASEPRI R/W 0x0000.0000 Base Priority Mask Register 57 - CONTROL R/W 0x0000.0000 Control Register 58 2.3.4 Description See page Name Register Descriptions This section lists and describes the Cortex-M3 registers, in the order shown in Figure 2-3 on page 45. The core registers are not memory mapped and are accessed by register name rather than offset. Note: The register type shown in the register descriptions refers to type during program execution in Thread mode and Handler mode. Debug access can differ. 46 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 1: Cortex General-Purpose Register 0 (R0) Register 2: Cortex General-Purpose Register 1 (R1) Register 3: Cortex General-Purpose Register 2 (R2) Register 4: Cortex General-Purpose Register 3 (R3) Register 5: Cortex General-Purpose Register 4 (R4) Register 6: Cortex General-Purpose Register 5 (R5) Register 7: Cortex General-Purpose Register 6 (R6) Register 8: Cortex General-Purpose Register 7 (R7) Register 9: Cortex General-Purpose Register 8 (R8) Register 10: Cortex General-Purpose Register 9 (R9) Register 11: Cortex General-Purpose Register 10 (R10) Register 12: Cortex General-Purpose Register 11 (R11) Register 13: Cortex General-Purpose Register 12 (R12) The Rn registers are 32-bit general-purpose registers for data operations and can be accessed from either privileged or unprivileged mode. Cortex General-Purpose Register 0 (R0) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - DATA Type Reset DATA Type Reset Bit/Field Name Type Reset 31:0 DATA R/W - Description Register data. July 14, 2014 47 Texas Instruments-Production Data The Cortex-M3 Processor Register 14: Stack Pointer (SP) The Stack Pointer (SP) is register R13. In Thread mode, the function of this register changes depending on the ASP bit in the Control Register (CONTROL) register. When the ASP bit is clear, this register is the Main Stack Pointer (MSP). When the ASP bit is set, this register is the Process Stack Pointer (PSP). On reset, the ASP bit is clear, and the processor loads the MSP with the value from address 0x0000.0000. The MSP can only be accessed in privileged mode; the PSP can be accessed in either privileged or unprivileged mode. Stack Pointer (SP) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - SP Type Reset SP Type Reset Bit/Field Name Type Reset 31:0 SP R/W - Description This field is the address of the stack pointer. 48 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 15: Link Register (LR) The Link Register (LR) is register R14, and it stores the return information for subroutines, function calls, and exceptions. LR can be accessed from either privileged or unprivileged mode. EXC_RETURN is loaded into LR on exception entry. See Table 2-10 on page 74 for the values and description. Link Register (LR) Type R/W, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 LINK Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 15 14 13 12 11 10 9 8 LINK Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type 31:0 LINK R/W R/W 1 Reset R/W 1 Description 0xFFFF.FFFF This field is the return address. July 14, 2014 49 Texas Instruments-Production Data The Cortex-M3 Processor Register 16: Program Counter (PC) The Program Counter (PC) is register R15, and it contains the current program address. On reset, the processor loads the PC with the value of the reset vector, which is at address 0x0000.0004. Bit 0 of the reset vector is loaded into the THUMB bit of the EPSR at reset and must be 1. The PC register can be accessed in either privileged or unprivileged mode. Program Counter (PC) Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - PC Type Reset PC Type Reset Bit/Field Name Type Reset 31:0 PC R/W - Description This field is the current program address. 50 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: Program Status Register (PSR) Note: This register is also referred to as xPSR. The Program Status Register (PSR) has three functions, and the register bits are assigned to the different functions: ■ Application Program Status Register (APSR), bits 31:27, ■ Execution Program Status Register (EPSR), bits 26:24, 15:10 ■ Interrupt Program Status Register (IPSR), bits 5:0 The PSR, IPSR, and EPSR registers can only be accessed in privileged mode; the APSR register can be accessed in either privileged or unprivileged mode. APSR contains the current state of the condition flags from previous instruction executions. EPSR contains the Thumb state bit and the execution state bits for the If-Then (IT) instruction or the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction. Attempts to read the EPSR directly through application software using the MSR instruction always return zero. Attempts to write the EPSR using the MSR instruction in application software are always ignored. Fault handlers can examine the EPSR value in the stacked PSR to determine the operation that faulted (see “Exception Entry and Return” on page 72). IPSR contains the exception type number of the current Interrupt Service Routine (ISR). These registers can be accessed individually or as a combination of any two or all three registers, using the register name as an argument to the MSR or MRS instructions. For example, all of the registers can be read using PSR with the MRS instruction, or APSR only can be written to using APSR with the MSR instruction. page 51 shows the possible register combinations for the PSR. See the MRS and MSR instruction descriptions in the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information about how to access the program status registers. Table 2-3. PSR Register Combinations Register Type PSR R/W Combination APSR, EPSR, and IPSR IEPSR RO EPSR and IPSR a, b a APSR and IPSR b APSR and EPSR IAPSR R/W EAPSR R/W a. The processor ignores writes to the IPSR bits. b. Reads of the EPSR bits return zero, and the processor ignores writes to these bits. Program Status Register (PSR) Type R/W, reset 0x0100.0000 Type Reset 31 30 29 28 27 N Z C V Q 26 25 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 ICI / IT ICI / IT Type Reset RO 0 RO 0 RO 0 24 23 22 21 20 THUMB reserved RO 0 RO 0 RO 0 RO 0 RO 0 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 reserved RO 0 ISRNUM RO 0 July 14, 2014 RO 0 RO 0 RO 0 51 Texas Instruments-Production Data The Cortex-M3 Processor Bit/Field Name Type Reset 31 N R/W 0 Description APSR Negative or Less Flag Value Description 1 The previous operation result was negative or less than. 0 The previous operation result was positive, zero, greater than, or equal. The value of this bit is only meaningful when accessing PSR or APSR. 30 Z R/W 0 APSR Zero Flag Value Description 1 The previous operation result was zero. 0 The previous operation result was non-zero. The value of this bit is only meaningful when accessing PSR or APSR. 29 C R/W 0 APSR Carry or Borrow Flag Value Description 1 The previous add operation resulted in a carry bit or the previous subtract operation did not result in a borrow bit. 0 The previous add operation did not result in a carry bit or the previous subtract operation resulted in a borrow bit. The value of this bit is only meaningful when accessing PSR or APSR. 28 V R/W 0 APSR Overflow Flag Value Description 1 The previous operation resulted in an overflow. 0 The previous operation did not result in an overflow. The value of this bit is only meaningful when accessing PSR or APSR. 27 Q R/W 0 APSR DSP Overflow and Saturation Flag Value Description 1 DSP Overflow or saturation has occurred. 0 DSP overflow or saturation has not occurred since reset or since the bit was last cleared. The value of this bit is only meaningful when accessing PSR or APSR. This bit is cleared by software using an MRS instruction. 52 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 26:25 ICI / IT RO 0x0 Description EPSR ICI / IT status These bits, along with bits 15:10, contain the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction or the execution state bits of the IT instruction. When EPSR holds the ICI execution state, bits 26:25 are zero. The If-Then block contains up to four instructions following an IT instruction. Each instruction in the block is conditional. The conditions for the instructions are either all the same, or some can be the inverse of others. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. The value of this field is only meaningful when accessing PSR or EPSR. 24 THUMB RO 1 EPSR Thumb State This bit indicates the Thumb state and should always be set. The following can clear the THUMB bit: ■ The BLX, BX and POP{PC} instructions ■ Restoration from the stacked xPSR value on an exception return ■ Bit 0 of the vector value on an exception entry or reset Attempting to execute instructions when this bit is clear results in a fault or lockup. See “Lockup” on page 76 for more information. The value of this bit is only meaningful when accessing PSR or EPSR. 23:16 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:10 ICI / IT RO 0x0 EPSR ICI / IT status These bits, along with bits 26:25, contain the Interruptible-Continuable Instruction (ICI) field for an interrupted load multiple or store multiple instruction or the execution state bits of the IT instruction. When an interrupt occurs during the execution of an LDM, STM, PUSH or POP instruction, the processor stops the load multiple or store multiple instruction operation temporarily and stores the next register operand in the multiple operation to bits 15:12. After servicing the interrupt, the processor returns to the register pointed to by bits 15:12 and resumes execution of the multiple load or store instruction. When EPSR holds the ICI execution state, bits 11:10 are zero. The If-Then block contains up to four instructions following a 16-bit IT instruction. Each instruction in the block is conditional. The conditions for the instructions are either all the same, or some can be the inverse of others. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. The value of this field is only meaningful when accessing PSR or EPSR. 9:6 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 53 Texas Instruments-Production Data The Cortex-M3 Processor Bit/Field Name Type Reset Description 5:0 ISRNUM RO 0x00 IPSR ISR Number This field contains the exception type number of the current Interrupt Service Routine (ISR). Value Description 0x00 Thread mode 0x01 Reserved 0x02 NMI 0x03 Hard fault 0x04 Memory management fault 0x05 Bus fault 0x06 Usage fault 0x07-0x0A Reserved 0x0B SVCall 0x0C Reserved for Debug 0x0D Reserved 0x0E PendSV 0x0F SysTick 0x10 Interrupt Vector 0 0x11 Interrupt Vector 1 ... ... 0x2D Interrupt Vector 29 0x2E-0x3F Reserved See “Exception Types” on page 68 for more information. The value of this field is only meaningful when accessing PSR or IPSR. 54 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 18: Priority Mask Register (PRIMASK) The PRIMASK register prevents activation of all exceptions with programmable priority. Reset, non-maskable interrupt (NMI), and hard fault are the only exceptions with fixed priority. Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. The MSR and MRS instructions are used to access the PRIMASK register, and the CPS instruction may be used to change the value of the PRIMASK register. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information on these instructions. For more information on exception priority levels, see “Exception Types” on page 68. Priority Mask Register (PRIMASK) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 PRIMASK R/W 0 RO 0 PRIMASK R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Priority Mask Value Description 1 Prevents the activation of all exceptions with configurable priority. 0 No effect. July 14, 2014 55 Texas Instruments-Production Data The Cortex-M3 Processor Register 19: Fault Mask Register (FAULTMASK) The FAULTMASK register prevents activation of all exceptions except for the Non-Maskable Interrupt (NMI). Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. The MSR and MRS instructions are used to access the FAULTMASK register, and the CPS instruction may be used to change the value of the FAULTMASK register. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information on these instructions. For more information on exception priority levels, see “Exception Types” on page 68. Fault Mask Register (FAULTMASK) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0000.000 0 FAULTMASK R/W 0 RO 0 FAULTMASK R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Fault Mask Value Description 1 Prevents the activation of all exceptions except for NMI. 0 No effect. The processor clears the FAULTMASK bit on exit from any exception handler except the NMI handler. 56 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 20: Base Priority Mask Register (BASEPRI) The BASEPRI register defines the minimum priority for exception processing. When BASEPRI is set to a nonzero value, it prevents the activation of all exceptions with the same or lower priority level as the BASEPRI value. Exceptions should be disabled when they might impact the timing of critical tasks. This register is only accessible in privileged mode. For more information on exception priority levels, see “Exception Types” on page 68. Base Priority Mask Register (BASEPRI) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset BASEPRI RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0x0000.00 7:5 BASEPRI R/W 0x0 R/W 0 reserved RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Base Priority Any exception that has a programmable priority level with the same or lower priority as the value of this field is masked. The PRIMASK register can be used to mask all exceptions with programmable priority levels. Higher priority exceptions have lower priority levels. Value Description 4:0 reserved RO 0x0 0x0 All exceptions are unmasked. 0x1 All exceptions with priority level 1-7 are masked. 0x2 All exceptions with priority level 2-7 are masked. 0x3 All exceptions with priority level 3-7 are masked. 0x4 All exceptions with priority level 4-7 are masked. 0x5 All exceptions with priority level 5-7 are masked. 0x6 All exceptions with priority level 6-7 are masked. 0x7 All exceptions with priority level 7 are masked. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 57 Texas Instruments-Production Data The Cortex-M3 Processor Register 21: Control Register (CONTROL) The CONTROL register controls the stack used and the privilege level for software execution when the processor is in Thread mode. This register is only accessible in privileged mode. Handler mode always uses MSP, so the processor ignores explicit writes to the ASP bit of the CONTROL register when in Handler mode. The exception entry and return mechanisms automatically update the CONTROL register based on the EXC_RETURN value (see Table 2-10 on page 74). In an OS environment, threads running in Thread mode should use the process stack and the kernel and exception handlers should use the main stack. By default, Thread mode uses MSP. To switch the stack pointer used in Thread mode to PSP, either use the MSR instruction to set the ASP bit, as detailed in the Cortex™-M3/M4 Instruction Set Technical User's Manual, or perform an exception return to Thread mode with the appropriate EXC_RETURN value, as shown in Table 2-10 on page 74. Note: When changing the stack pointer, software must use an ISB instruction immediately after the MSR instruction, ensuring that instructions after the ISB execute use the new stack pointer. See the Cortex™-M3/M4 Instruction Set Technical User's Manual. Control Register (CONTROL) Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 ASP TMPL RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0000.000 1 ASP R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Active Stack Pointer Value Description 1 PSP is the current stack pointer. 0 MSP is the current stack pointer In Handler mode, this bit reads as zero and ignores writes. The Cortex-M3 updates this bit automatically on exception return. 0 TMPL R/W 0 Thread Mode Privilege Level Value Description 1 Unprivileged software can be executed in Thread mode. 0 Only privileged software can be executed in Thread mode. 58 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 2.3.5 Exceptions and Interrupts The Cortex-M3 processor supports interrupts and system exceptions. The processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions. An exception changes the normal flow of software control. The processor uses Handler mode to handle all exceptions except for reset. See “Exception Entry and Return” on page 72 for more information. The NVIC registers control interrupt handling. See “Nested Vectored Interrupt Controller (NVIC)” on page 83 for more information. 2.3.6 Data Types The Cortex-M3 supports 32-bit words, 16-bit halfwords, and 8-bit bytes. The processor also supports 64-bit data transfer instructions. All instruction and data memory accesses are little endian. See “Memory Regions, Types and Attributes” on page 60 for more information. 2.4 Memory Model This section describes the processor memory map, the behavior of memory accesses, and the bit-banding features. The processor has a fixed memory map that provides up to 4 GB of addressable memory. The memory map for the LM3S600 controller is provided in Table 2-4 on page 59. In this manual, register addresses are given as a hexadecimal increment, relative to the module’s base address as shown in the memory map. The regions for SRAM and peripherals include bit-band regions. Bit-banding provides atomic operations to bit data (see “Bit-Banding” on page 63). The processor reserves regions of the Private peripheral bus (PPB) address range for core peripheral registers (see “Cortex-M3 Peripherals” on page 82). Note: Within the memory map, all reserved space returns a bus fault when read or written. Table 2-4. Memory Map Start End Description For details, see page ... 0x0000.0000 0x0000.7FFF On-chip Flash 211 0x0000.8000 0x1FFF.FFFF Reserved - 0x2000.0000 0x2000.1FFF Bit-banded on-chip SRAM 205 0x2000.2000 0x21FF.FFFF Reserved - 0x2200.0000 0x2203.FFFF Bit-band alias of bit-banded on-chip SRAM starting at 0x2000.0000 205 0x2204.0000 0x3FFF.FFFF Reserved - 0x4000.0000 0x4000.0FFF Watchdog timer 0 302 0x4000.1000 0x4000.3FFF Reserved - 0x4000.4000 0x4000.4FFF GPIO Port A 231 0x4000.5000 0x4000.5FFF GPIO Port B 231 0x4000.6000 0x4000.6FFF GPIO Port C 231 0x4000.7000 0x4000.7FFF GPIO Port D 231 0x4000.8000 0x4000.8FFF SSI0 375 Memory FiRM Peripherals July 14, 2014 59 Texas Instruments-Production Data The Cortex-M3 Processor Table 2-4. Memory Map (continued) Start End Description For details, see page ... 0x4000.9000 0x4000.BFFF Reserved - 0x4000.C000 0x4000.CFFF UART0 330 0x4000.D000 0x4000.DFFF UART1 330 0x4000.E000 0x4001.FFFF Reserved - 0x4002.0000 0x4002.0FFF I2C 0 416 0x4002.1000 0x4002.3FFF Reserved - 0x4002.4000 0x4002.4FFF GPIO Port E 231 0x4002.5000 0x4002.FFFF Reserved - 0x4003.0000 0x4003.0FFF Timer 0 274 0x4003.1000 0x4003.1FFF Timer 1 274 0x4003.2000 0x4003.2FFF Timer 2 274 0x4003.3000 0x4003.BFFF Reserved - 0x4003.C000 0x4003.CFFF Analog Comparators 438 0x4003.D000 0x400F.CFFF Reserved - 0x400F.D000 0x400F.DFFF Flash memory control 211 0x400F.E000 0x400F.EFFF System control 161 0x400F.F000 0x41FF.FFFF Reserved - 0x4200.0000 0x43FF.FFFF Bit-banded alias of 0x4000.0000 through 0x400F.FFFF - 0x4400.0000 0xDFFF.FFFF Reserved - 0xE000.0000 0xE000.0FFF Instrumentation Trace Macrocell (ITM) 42 0xE000.1000 0xE000.1FFF Data Watchpoint and Trace (DWT) 42 0xE000.2000 0xE000.2FFF Flash Patch and Breakpoint (FPB) 42 0xE000.3000 0xE000.DFFF Reserved - 0xE000.E000 0xE000.EFFF Cortex-M3 Peripherals (SysTick, NVIC, MPU and SCB) 90 0xE000.F000 0xE003.FFFF Reserved - 0xE004.0000 0xE004.0FFF Trace Port Interface Unit (TPIU) 43 0xE004.1000 0xFFFF.FFFF Reserved - Peripherals Private Peripheral Bus 2.4.1 Memory Regions, Types and Attributes The memory map and the programming of the MPU split the memory map into regions. Each region has a defined memory type, and some regions have additional memory attributes. The memory type and attributes determine the behavior of accesses to the region. The memory types are: ■ Normal: The processor can re-order transactions for efficiency and perform speculative reads. ■ Device: The processor preserves transaction order relative to other transactions to Device or Strongly Ordered memory. ■ Strongly Ordered: The processor preserves transaction order relative to all other transactions. 60 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller The different ordering requirements for Device and Strongly Ordered memory mean that the memory system can buffer a write to Device memory but must not buffer a write to Strongly Ordered memory. An additional memory attribute is Execute Never (XN), which means the processor prevents instruction accesses. A fault exception is generated only on execution of an instruction executed from an XN region. 2.4.2 Memory System Ordering of Memory Accesses For most memory accesses caused by explicit memory access instructions, the memory system does not guarantee that the order in which the accesses complete matches the program order of the instructions, providing the order does not affect the behavior of the instruction sequence. Normally, if correct program execution depends on two memory accesses completing in program order, software must insert a memory barrier instruction between the memory access instructions (see “Software Ordering of Memory Accesses” on page 62). However, the memory system does guarantee ordering of accesses to Device and Strongly Ordered memory. For two memory access instructions A1 and A2, if both A1 and A2 are accesses to either Device or Strongly Ordered memory, and if A1 occurs before A2 in program order, A1 is always observed before A2. 2.4.3 Behavior of Memory Accesses Table 2-5 on page 61 shows the behavior of accesses to each region in the memory map. See “Memory Regions, Types and Attributes” on page 60 for more information on memory types and the XN attribute. Stellaris devices may have reserved memory areas within the address ranges shown below (refer to Table 2-4 on page 59 for more information). Table 2-5. Memory Access Behavior Address Range Memory Region Memory Type Execute Never (XN) Description 0x0000.0000 - 0x1FFF.FFFF Code Normal - This executable region is for program code. Data can also be stored here. 0x2000.0000 - 0x3FFF.FFFF SRAM Normal - This executable region is for data. Code can also be stored here. This region includes bit band and bit band alias areas (see Table 2-6 on page 63). 0x4000.0000 - 0x5FFF.FFFF Peripheral Device XN This region includes bit band and bit band alias areas (see Table 2-7 on page 63). 0x6000.0000 - 0x9FFF.FFFF External RAM Normal - This executable region is for data. 0xA000.0000 - 0xDFFF.FFFF External device Device XN This region is for external device memory. 0xE000.0000- 0xE00F.FFFF Private peripheral bus Strongly Ordered XN This region includes the NVIC, system timer, and system control block. 0xE010.0000- 0xFFFF.FFFF Reserved - - - The Code, SRAM, and external RAM regions can hold programs. However, it is recommended that programs always use the Code region because the Cortex-M3 has separate buses that can perform instruction fetches and data accesses simultaneously. The MPU can override the default memory access behavior described in this section. For more information, see “Memory Protection Unit (MPU)” on page 85. The Cortex-M3 prefetches instructions ahead of execution and speculatively prefetches from branch target addresses. July 14, 2014 61 Texas Instruments-Production Data The Cortex-M3 Processor 2.4.4 Software Ordering of Memory Accesses The order of instructions in the program flow does not always guarantee the order of the corresponding memory transactions for the following reasons: ■ The processor can reorder some memory accesses to improve efficiency, providing this does not affect the behavior of the instruction sequence. ■ The processor has multiple bus interfaces. ■ Memory or devices in the memory map have different wait states. ■ Some memory accesses are buffered or speculative. “Memory System Ordering of Memory Accesses” on page 61 describes the cases where the memory system guarantees the order of memory accesses. Otherwise, if the order of memory accesses is critical, software must include memory barrier instructions to force that ordering. The Cortex-M3 has the following memory barrier instructions: ■ The Data Memory Barrier (DMB) instruction ensures that outstanding memory transactions complete before subsequent memory transactions. ■ The Data Synchronization Barrier (DSB) instruction ensures that outstanding memory transactions complete before subsequent instructions execute. ■ The Instruction Synchronization Barrier (ISB) instruction ensures that the effect of all completed memory transactions is recognizable by subsequent instructions. Memory barrier instructions can be used in the following situations: ■ MPU programming – If the MPU settings are changed and the change must be effective on the very next instruction, use a DSB instruction to ensure the effect of the MPU takes place immediately at the end of context switching. – Use an ISB instruction to ensure the new MPU setting takes effect immediately after programming the MPU region or regions, if the MPU configuration code was accessed using a branch or call. If the MPU configuration code is entered using exception mechanisms, then an ISB instruction is not required. ■ Vector table If the program changes an entry in the vector table and then enables the corresponding exception, use a DMB instruction between the operations. The DMB instruction ensures that if the exception is taken immediately after being enabled, the processor uses the new exception vector. ■ Self-modifying code If a program contains self-modifying code, use an ISB instruction immediately after the code modification in the program. The ISB instruction ensures subsequent instruction execution uses the updated program. ■ Memory map switching 62 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller If the system contains a memory map switching mechanism, use a DSB instruction after switching the memory map in the program. The DSB instruction ensures subsequent instruction execution uses the updated memory map. ■ Dynamic exception priority change When an exception priority has to change when the exception is pending or active, use DSB instructions after the change. The change then takes effect on completion of the DSB instruction. Memory accesses to Strongly Ordered memory, such as the System Control Block, do not require the use of DMB instructions. For more information on the memory barrier instructions, see the Cortex™-M3/M4 Instruction Set Technical User's Manual. 2.4.5 Bit-Banding A bit-band region maps each word in a bit-band alias region to a single bit in the bit-band region. The bit-band regions occupy the lowest 1 MB of the SRAM and peripheral memory regions. Accesses to the 32-MB SRAM alias region map to the 1-MB SRAM bit-band region, as shown in Table 2-6 on page 63. Accesses to the 32-MB peripheral alias region map to the 1-MB peripheral bit-band region, as shown in Table 2-7 on page 63. For the specific address range of the bit-band regions, see Table 2-4 on page 59. Note: A word access to the SRAM or the peripheral bit-band alias region maps to a single bit in the SRAM or peripheral bit-band region. A word access to a bit band address results in a word access to the underlying memory, and similarly for halfword and byte accesses. This allows bit band accesses to match the access requirements of the underlying peripheral. Table 2-6. SRAM Memory Bit-Banding Regions Address Range Memory Region Instruction and Data Accesses Start End 0x2000.0000 0x2000.1FFF SRAM bit-band region Direct accesses to this memory range behave as SRAM memory accesses, but this region is also bit addressable through bit-band alias. 0x2200.0000 0x2203.FFFF SRAM bit-band alias Data accesses to this region are remapped to bit band region. A write operation is performed as read-modify-write. Instruction accesses are not remapped. Table 2-7. Peripheral Memory Bit-Banding Regions Address Range Memory Region Instruction and Data Accesses 0x400F.FFFF Peripheral bit-band region Direct accesses to this memory range behave as peripheral memory accesses, but this region is also bit addressable through bit-band alias. 0x43FF.FFFF Peripheral bit-band alias Data accesses to this region are remapped to bit band region. A write operation is performed as read-modify-write. Instruction accesses are not permitted. Start End 0x4000.0000 0x4200.0000 The following formula shows how the alias region maps onto the bit-band region: bit_word_offset = (byte_offset x 32) + (bit_number x 4) July 14, 2014 63 Texas Instruments-Production Data The Cortex-M3 Processor bit_word_addr = bit_band_base + bit_word_offset where: bit_word_offset The position of the target bit in the bit-band memory region. bit_word_addr The address of the word in the alias memory region that maps to the targeted bit. bit_band_base The starting address of the alias region. byte_offset The number of the byte in the bit-band region that contains the targeted bit. bit_number The bit position, 0-7, of the targeted bit. Figure 2-4 on page 65 shows examples of bit-band mapping between the SRAM bit-band alias region and the SRAM bit-band region: ■ The alias word at 0x23FF.FFE0 maps to bit 0 of the bit-band byte at 0x200F.FFFF: 0x23FF.FFE0 = 0x2200.0000 + (0x000F.FFFF*32) + (0*4) ■ The alias word at 0x23FF.FFFC maps to bit 7 of the bit-band byte at 0x200F.FFFF: 0x23FF.FFFC = 0x2200.0000 + (0x000F.FFFF*32) + (7*4) ■ The alias word at 0x2200.0000 maps to bit 0 of the bit-band byte at 0x2000.0000: 0x2200.0000 = 0x2200.0000 + (0*32) + (0*4) ■ The alias word at 0x2200.001C maps to bit 7 of the bit-band byte at 0x2000.0000: 0x2200.001C = 0x2200.0000+ (0*32) + (7*4) 64 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 2-4. Bit-Band Mapping 32-MB Alias Region 0x23FF.FFFC 0x23FF.FFF8 0x23FF.FFF4 0x23FF.FFF0 0x23FF.FFEC 0x23FF.FFE8 0x23FF.FFE4 0x23FF.FFE0 0x2200.001C 0x2200.0018 0x2200.0014 0x2200.0010 0x2200.000C 0x2200.0008 0x2200.0004 0x2200.0000 7 3 1-MB SRAM Bit-Band Region 7 6 5 4 3 2 1 0 7 6 0x200F.FFFF 7 6 5 4 3 2 0x2000.0003 2.4.5.1 5 4 3 2 1 0 7 6 0x200F.FFFE 1 0 7 6 5 4 3 2 5 4 3 2 1 0 6 0x200F.FFFD 1 0 0x2000.0002 7 6 5 4 3 2 0x2000.0001 5 4 2 1 0 1 0 0x200F.FFFC 1 0 7 6 5 4 3 2 0x2000.0000 Directly Accessing an Alias Region Writing to a word in the alias region updates a single bit in the bit-band region. Bit 0 of the value written to a word in the alias region determines the value written to the targeted bit in the bit-band region. Writing a value with bit 0 set writes a 1 to the bit-band bit, and writing a value with bit 0 clear writes a 0 to the bit-band bit. Bits 31:1 of the alias word have no effect on the bit-band bit. Writing 0x01 has the same effect as writing 0xFF. Writing 0x00 has the same effect as writing 0x0E. When reading a word in the alias region, 0x0000.0000 indicates that the targeted bit in the bit-band region is clear and 0x0000.0001 indicates that the targeted bit in the bit-band region is set. 2.4.5.2 Directly Accessing a Bit-Band Region “Behavior of Memory Accesses” on page 61 describes the behavior of direct byte, halfword, or word accesses to the bit-band regions. 2.4.6 Data Storage The processor views memory as a linear collection of bytes numbered in ascending order from zero. For example, bytes 0-3 hold the first stored word, and bytes 4-7 hold the second stored word. Data is stored in little-endian format, with the least-significant byte (lsbyte) of a word stored at the lowest-numbered byte, and the most-significant byte (msbyte) stored at the highest-numbered byte. Figure 2-5 on page 66 illustrates how data is stored. July 14, 2014 65 Texas Instruments-Production Data The Cortex-M3 Processor Figure 2-5. Data Storage Memory 7 Register 0 31 2.4.7 Address A B0 A+1 B1 A+2 B2 A+3 B3 lsbyte 24 23 B3 16 15 B2 8 7 B1 0 B0 msbyte Synchronization Primitives The Cortex-M3 instruction set includes pairs of synchronization primitives which provide a non-blocking mechanism that a thread or process can use to obtain exclusive access to a memory location. Software can use these primitives to perform a guaranteed read-modify-write memory update sequence or for a semaphore mechanism. A pair of synchronization primitives consists of: ■ A Load-Exclusive instruction, which is used to read the value of a memory location and requests exclusive access to that location. ■ A Store-Exclusive instruction, which is used to attempt to write to the same memory location and returns a status bit to a register. If this status bit is clear, it indicates that the thread or process gained exclusive access to the memory and the write succeeds; if this status bit is set, it indicates that the thread or process did not gain exclusive access to the memory and no write was performed. The pairs of Load-Exclusive and Store-Exclusive instructions are: ■ The word instructions LDREX and STREX ■ The halfword instructions LDREXH and STREXH ■ The byte instructions LDREXB and STREXB Software must use a Load-Exclusive instruction with the corresponding Store-Exclusive instruction. To perform an exclusive read-modify-write of a memory location, software must: 1. Use a Load-Exclusive instruction to read the value of the location. 2. Modify the value, as required. 3. Use a Store-Exclusive instruction to attempt to write the new value back to the memory location. 4. Test the returned status bit. If the status bit is clear, the read-modify-write completed successfully. If the status bit is set, no write was performed, which indicates that the value returned at step 1 might be out of date. The software must retry the entire read-modify-write sequence. Software can use the synchronization primitives to implement a semaphore as follows: 66 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 1. Use a Load-Exclusive instruction to read from the semaphore address to check whether the semaphore is free. 2. If the semaphore is free, use a Store-Exclusive to write the claim value to the semaphore address. 3. If the returned status bit from step 2 indicates that the Store-Exclusive succeeded, then the software has claimed the semaphore. However, if the Store-Exclusive failed, another process might have claimed the semaphore after the software performed step 1. The Cortex-M3 includes an exclusive access monitor that tags the fact that the processor has executed a Load-Exclusive instruction. The processor removes its exclusive access tag if: ■ It executes a CLREX instruction. ■ It executes a Store-Exclusive instruction, regardless of whether the write succeeds. ■ An exception occurs, which means the processor can resolve semaphore conflicts between different threads. For more information about the synchronization primitive instructions, see the Cortex™-M3/M4 Instruction Set Technical User's Manual. 2.5 Exception Model The ARM Cortex-M3 processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and handle all exceptions in Handler Mode. The processor state is automatically stored to the stack on an exception and automatically restored from the stack at the end of the Interrupt Service Routine (ISR). The vector is fetched in parallel to the state saving, enabling efficient interrupt entry. The processor supports tail-chaining, which enables back-to-back interrupts to be performed without the overhead of state saving and restoration. Table 2-8 on page 69 lists all exception types. Software can set eight priority levels on seven of these exceptions (system handlers) as well as on 21 interrupts (listed in Table 2-9 on page 70). Priorities on the system handlers are set with the NVIC System Handler Priority n (SYSPRIn) registers. Interrupts are enabled through the NVIC Interrupt Set Enable n (ENn) register and prioritized with the NVIC Interrupt Priority n (PRIn) registers. Priorities can be grouped by splitting priority levels into preemption priorities and subpriorities. All the interrupt registers are described in “Nested Vectored Interrupt Controller (NVIC)” on page 83. Internally, the highest user-programmable priority (0) is treated as fourth priority, after a Reset, Non-Maskable Interrupt (NMI), and a Hard Fault, in that order. Note that 0 is the default priority for all the programmable priorities. Important: After a write to clear an interrupt source, it may take several processor cycles for the NVIC to see the interrupt source de-assert. Thus if the interrupt clear is done as the last action in an interrupt handler, it is possible for the interrupt handler to complete while the NVIC sees the interrupt as still asserted, causing the interrupt handler to be re-entered errantly. This situation can be avoided by either clearing the interrupt source at the beginning of the interrupt handler or by performing a read or write after the write to clear the interrupt source (and flush the write buffer). See “Nested Vectored Interrupt Controller (NVIC)” on page 83 for more information on exceptions and interrupts. July 14, 2014 67 Texas Instruments-Production Data The Cortex-M3 Processor 2.5.1 Exception States Each exception is in one of the following states: ■ Inactive. The exception is not active and not pending. ■ Pending. The exception is waiting to be serviced by the processor. An interrupt request from a peripheral or from software can change the state of the corresponding interrupt to pending. ■ Active. An exception that is being serviced by the processor but has not completed. Note: An exception handler can interrupt the execution of another exception handler. In this case, both exceptions are in the active state. ■ Active and Pending. The exception is being serviced by the processor, and there is a pending exception from the same source. 2.5.2 Exception Types The exception types are: ■ Reset. Reset is invoked on power up or a warm reset. The exception model treats reset as a special form of exception. When reset is asserted, the operation of the processor stops, potentially at any point in an instruction. When reset is deasserted, execution restarts from the address provided by the reset entry in the vector table. Execution restarts as privileged execution in Thread mode. ■ NMI. A non-maskable Interrupt (NMI) can be signaled using the NMI signal or triggered by software using the Interrupt Control and State (INTCTRL) register. This exception has the highest priority other than reset. NMI is permanently enabled and has a fixed priority of -2. NMIs cannot be masked or prevented from activation by any other exception or preempted by any exception other than reset. ■ Hard Fault. A hard fault is an exception that occurs because of an error during exception processing, or because an exception cannot be managed by any other exception mechanism. Hard faults have a fixed priority of -1, meaning they have higher priority than any exception with configurable priority. ■ Memory Management Fault. A memory management fault is an exception that occurs because of a memory protection related fault, including access violation and no match. The MPU or the fixed memory protection constraints determine this fault, for both instruction and data memory transactions. This fault is used to abort instruction accesses to Execute Never (XN) memory regions, even if the MPU is disabled. ■ Bus Fault. A bus fault is an exception that occurs because of a memory-related fault for an instruction or data memory transaction such as a prefetch fault or a memory access fault. This fault can be enabled or disabled. ■ Usage Fault. A usage fault is an exception that occurs because of a fault related to instruction execution, such as: – An undefined instruction – An illegal unaligned access – Invalid state on instruction execution 68 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller – An error on exception return An unaligned address on a word or halfword memory access or division by zero can cause a usage fault when the core is properly configured. ■ SVCall. A supervisor call (SVC) is an exception that is triggered by the SVC instruction. In an OS environment, applications can use SVC instructions to access OS kernel functions and device drivers. ■ Debug Monitor. This exception is caused by the debug monitor (when not halting). This exception is only active when enabled. This exception does not activate if it is a lower priority than the current activation. ■ PendSV. PendSV is a pendable, interrupt-driven request for system-level service. In an OS environment, use PendSV for context switching when no other exception is active. PendSV is triggered using the Interrupt Control and State (INTCTRL) register. ■ SysTick. A SysTick exception is an exception that the system timer generates when it reaches zero when it is enabled to generate an interrupt. Software can also generate a SysTick exception using the Interrupt Control and State (INTCTRL) register. In an OS environment, the processor can use this exception as system tick. ■ Interrupt (IRQ). An interrupt, or IRQ, is an exception signaled by a peripheral or generated by a software request and fed through the NVIC (prioritized). All interrupts are asynchronous to instruction execution. In the system, peripherals use interrupts to communicate with the processor. Table 2-9 on page 70 lists the interrupts on the LM3S600 controller. For an asynchronous exception, other than reset, the processor can execute another instruction between when the exception is triggered and when the processor enters the exception handler. Privileged software can disable the exceptions that Table 2-8 on page 69 shows as having configurable priority (see the SYSHNDCTRL register on page 118 and the DIS0 register on page 97). For more information about hard faults, memory management faults, bus faults, and usage faults, see “Fault Handling” on page 74. Table 2-8. Exception Types Exception Type a Vector Number Priority Vector Address or b Offset - 0 - 0x0000.0000 Stack top is loaded from the first entry of the vector table on reset. Reset 1 -3 (highest) 0x0000.0004 Asynchronous Non-Maskable Interrupt (NMI) 2 -2 0x0000.0008 Asynchronous Hard Fault 3 -1 0x0000.000C - c 0x0000.0010 Synchronous c 0x0000.0014 Synchronous when precise and asynchronous when imprecise c Synchronous Memory Management 4 programmable Bus Fault 5 programmable Usage Fault 6 programmable 0x0000.0018 7-10 - - - Activation c c Reserved SVCall 11 programmable 0x0000.002C Synchronous Debug Monitor 12 programmable 0x0000.0030 Synchronous - 13 - - July 14, 2014 Reserved 69 Texas Instruments-Production Data The Cortex-M3 Processor Table 2-8. Exception Types (continued) Exception Type PendSV SysTick a Vector Number Priority 14 programmable 15 Interrupts Vector Address or b Offset c 0x0000.0038 Asynchronous c 0x0000.003C Asynchronous programmable 16 and above Activation d programmable 0x0000.0040 and above Asynchronous a. 0 is the default priority for all the programmable priorities. b. See “Vector Table” on page 71. c. See SYSPRI1 on page 115. d. See PRIn registers on page 101. Table 2-9. Interrupts 2.5.3 Vector Number Interrupt Number (Bit in Interrupt Registers) Vector Address or Offset Description 0-15 - 0x0000.0000 0x0000.003C 16 0 0x0000.0040 GPIO Port A 17 1 0x0000.0044 GPIO Port B 18 2 0x0000.0048 GPIO Port C 19 3 0x0000.004C GPIO Port D 20 4 0x0000.0050 GPIO Port E 21 5 0x0000.0054 UART0 22 6 0x0000.0058 UART1 23 7 0x0000.005C SSI0 24 8 0x0000.0060 I2C0 25-33 9-17 - 34 18 0x0000.0088 Watchdog Timer 0 35 19 0x0000.008C Timer 0A 36 20 0x0000.0090 Timer 0B 37 21 0x0000.0094 Timer 1A 38 22 0x0000.0098 Timer 1B 39 23 0x0000.009C Timer 2A 40 24 0x0000.00A0 Timer 2B 41 25 0x0000.00A4 Analog Comparator 0 42 26 0x0000.00A8 Analog Comparator 1 43 27 0x0000.00AC Analog Comparator 2 44 28 0x0000.00B0 System Control 45 29 0x0000.00B4 Flash Memory Control Processor exceptions Reserved Exception Handlers The processor handles exceptions using: ■ Interrupt Service Routines (ISRs). Interrupts (IRQx) are the exceptions handled by ISRs. ■ Fault Handlers. Hard fault, memory management fault, usage fault, and bus fault are fault exceptions handled by the fault handlers. 70 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ System Handlers. NMI, PendSV, SVCall, SysTick, and the fault exceptions are all system exceptions that are handled by system handlers. 2.5.4 Vector Table The vector table contains the reset value of the stack pointer and the start addresses, also called exception vectors, for all exception handlers. The vector table is constructed using the vector address or offset shown in Table 2-8 on page 69. Figure 2-6 on page 71 shows the order of the exception vectors in the vector table. The least-significant bit of each vector must be 1, indicating that the exception handler is Thumb code Figure 2-6. Vector Table Exception number IRQ number 45 29 . . . 18 2 17 1 16 0 15 -1 14 -2 13 Offset 0x00B4 . . . 0x004C 0x0048 0x0044 0x0040 0x003C 0x0038 12 11 Vector IRQ29 . . . IRQ2 IRQ1 IRQ0 Systick PendSV Reserved Reserved for Debug -5 10 0x002C 9 SVCall Reserved 8 7 6 -10 5 -11 4 -12 3 -13 2 -14 1 0x0018 0x0014 0x0010 0x000C 0x0008 0x0004 0x0000 Usage fault Bus fault Memory management fault Hard fault NMI Reset Initial SP value On system reset, the vector table is fixed at address 0x0000.0000. Privileged software can write to the Vector Table Offset (VTABLE) register to relocate the vector table start address to a different memory location, in the range 0x0000.0100 to 0x3FFF.FF00 (see “Vector Table” on page 71). Note that when configuring the VTABLE register, the offset must be aligned on a 256-byte boundary. 2.5.5 Exception Priorities As Table 2-8 on page 69 shows, all exceptions have an associated priority, with a lower priority value indicating a higher priority and configurable priorities for all exceptions except Reset, Hard fault, and NMI. If software does not configure any priorities, then all exceptions with a configurable July 14, 2014 71 Texas Instruments-Production Data The Cortex-M3 Processor priority have a priority of 0. For information about configuring exception priorities, see page 115 and page 101. Note: Configurable priority values for the Stellaris implementation are in the range 0-7. This means that the Reset, Hard fault, and NMI exceptions, with fixed negative priority values, always have higher priority than any other exception. For example, assigning a higher priority value to IRQ[0] and a lower priority value to IRQ[1] means that IRQ[1] has higher priority than IRQ[0]. If both IRQ[1] and IRQ[0] are asserted, IRQ[1] is processed before IRQ[0]. If multiple pending exceptions have the same priority, the pending exception with the lowest exception number takes precedence. For example, if both IRQ[0] and IRQ[1] are pending and have the same priority, then IRQ[0] is processed before IRQ[1]. When the processor is executing an exception handler, the exception handler is preempted if a higher priority exception occurs. If an exception occurs with the same priority as the exception being handled, the handler is not preempted, irrespective of the exception number. However, the status of the new interrupt changes to pending. 2.5.6 Interrupt Priority Grouping To increase priority control in systems with interrupts, the NVIC supports priority grouping. This grouping divides each interrupt priority register entry into two fields: ■ An upper field that defines the group priority ■ A lower field that defines a subpriority within the group Only the group priority determines preemption of interrupt exceptions. When the processor is executing an interrupt exception handler, another interrupt with the same group priority as the interrupt being handled does not preempt the handler. If multiple pending interrupts have the same group priority, the subpriority field determines the order in which they are processed. If multiple pending interrupts have the same group priority and subpriority, the interrupt with the lowest IRQ number is processed first. For information about splitting the interrupt priority fields into group priority and subpriority, see page 109. 2.5.7 Exception Entry and Return Descriptions of exception handling use the following terms: ■ Preemption. When the processor is executing an exception handler, an exception can preempt the exception handler if its priority is higher than the priority of the exception being handled. See “Interrupt Priority Grouping” on page 72 for more information about preemption by an interrupt. When one exception preempts another, the exceptions are called nested exceptions. See “Exception Entry” on page 73 more information. ■ Return. Return occurs when the exception handler is completed, and there is no pending exception with sufficient priority to be serviced and the completed exception handler was not handling a late-arriving exception. The processor pops the stack and restores the processor state to the state it had before the interrupt occurred. See “Exception Return” on page 74 for more information. 72 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ Tail-Chaining. This mechanism speeds up exception servicing. On completion of an exception handler, if there is a pending exception that meets the requirements for exception entry, the stack pop is skipped and control transfers to the new exception handler. ■ Late-Arriving. This mechanism speeds up preemption. If a higher priority exception occurs during state saving for a previous exception, the processor switches to handle the higher priority exception and initiates the vector fetch for that exception. State saving is not affected by late arrival because the state saved is the same for both exceptions. Therefore, the state saving continues uninterrupted. The processor can accept a late arriving exception until the first instruction of the exception handler of the original exception enters the execute stage of the processor. On return from the exception handler of the late-arriving exception, the normal tail-chaining rules apply. 2.5.7.1 Exception Entry Exception entry occurs when there is a pending exception with sufficient priority and either the processor is in Thread mode or the new exception is of higher priority than the exception being handled, in which case the new exception preempts the original exception. When one exception preempts another, the exceptions are nested. Sufficient priority means the exception has more priority than any limits set by the mask registers (see PRIMASK on page 55, FAULTMASK on page 56, and BASEPRI on page 57). An exception with less priority than this is pending but is not handled by the processor. When the processor takes an exception, unless the exception is a tail-chained or a late-arriving exception, the processor pushes information onto the current stack. This operation is referred to as stacking and the structure of eight data words is referred to as stack frame. Figure 2-7. Exception Stack Frame ... {aligner} xPSR PC LR R12 R3 R2 R1 R0 Pre-IRQ top of stack IRQ top of stack Immediately after stacking, the stack pointer indicates the lowest address in the stack frame. Unless stack alignment is disabled, the stack frame is aligned to a double-word address. If the STKALIGN bit of the Configuration Control (CCR) register is set, stack align adjustment is performed during stacking. The stack frame includes the return address, which is the address of the next instruction in the interrupted program. This value is restored to the PC at exception return so that the interrupted program resumes. In parallel to the stacking operation, the processor performs a vector fetch that reads the exception handler start address from the vector table. When stacking is complete, the processor starts executing the exception handler. At the same time, the processor writes an EXC_RETURN value to the LR, indicating which stack pointer corresponds to the stack frame and what operation mode the processor was in before the entry occurred. July 14, 2014 73 Texas Instruments-Production Data The Cortex-M3 Processor If no higher-priority exception occurs during exception entry, the processor starts executing the exception handler and automatically changes the status of the corresponding pending interrupt to active. If another higher-priority exception occurs during exception entry, known as late arrival, the processor starts executing the exception handler for this exception and does not change the pending status of the earlier exception. 2.5.7.2 Exception Return Exception return occurs when the processor is in Handler mode and executes one of the following instructions to load the EXC_RETURN value into the PC: ■ An LDM or POP instruction that loads the PC ■ A BX instruction using any register ■ An LDR instruction with the PC as the destination EXC_RETURN is the value loaded into the LR on exception entry. The exception mechanism relies on this value to detect when the processor has completed an exception handler. The lowest four bits of this value provide information on the return stack and processor mode. Table 2-10 on page 74 shows the EXC_RETURN values with a description of the exception return behavior. EXC_RETURN bits 31:4 are all set. When this value is loaded into the PC, it indicates to the processor that the exception is complete, and the processor initiates the appropriate exception return sequence. Table 2-10. Exception Return Behavior EXC_RETURN[31:0] Description 0xFFFF.FFF0 Reserved 0xFFFF.FFF1 Return to Handler mode. Exception return uses state from MSP. Execution uses MSP after return. 0xFFFF.FFF2 - 0xFFFF.FFF8 Reserved 0xFFFF.FFF9 Return to Thread mode. Exception return uses state from MSP. Execution uses MSP after return. 0xFFFF.FFFA - 0xFFFF.FFFC Reserved 0xFFFF.FFFD Return to Thread mode. Exception return uses state from PSP. Execution uses PSP after return. 0xFFFF.FFFE - 0xFFFF.FFFF 2.6 Reserved Fault Handling Faults are a subset of the exceptions (see “Exception Model” on page 67). The following conditions generate a fault: ■ A bus error on an instruction fetch or vector table load or a data access. ■ An internally detected error such as an undefined instruction or an attempt to change state with a BX instruction. 74 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ Attempting to execute an instruction from a memory region marked as Non-Executable (XN). ■ An MPU fault because of a privilege violation or an attempt to access an unmanaged region. 2.6.1 Fault Types Table 2-11 on page 75 shows the types of fault, the handler used for the fault, the corresponding fault status register, and the register bit that indicates the fault has occurred. See page 122 for more information about the fault status registers. Table 2-11. Faults Fault Handler Fault Status Register Bit Name Bus error on a vector read Hard fault Hard Fault Status (HFAULTSTAT) VECT Fault escalated to a hard fault Hard fault Hard Fault Status (HFAULTSTAT) FORCED MPU or default memory mismatch on Memory management instruction access fault Memory Management Fault Status (MFAULTSTAT) IERR MPU or default memory mismatch on Memory management data access fault Memory Management Fault Status (MFAULTSTAT) DERR MPU or default memory mismatch on Memory management exception stacking fault Memory Management Fault Status (MFAULTSTAT) MSTKE MPU or default memory mismatch on Memory management exception unstacking fault Memory Management Fault Status (MFAULTSTAT) MUSTKE Bus error during exception stacking Bus fault Bus Fault Status (BFAULTSTAT) BSTKE Bus error during exception unstacking Bus fault Bus Fault Status (BFAULTSTAT) BUSTKE Bus error during instruction prefetch Bus fault Bus Fault Status (BFAULTSTAT) IBUS Precise data bus error Bus fault Bus Fault Status (BFAULTSTAT) PRECISE Imprecise data bus error Bus fault Bus Fault Status (BFAULTSTAT) IMPRE Attempt to access a coprocessor Usage fault Usage Fault Status (UFAULTSTAT) NOCP Undefined instruction Usage fault Usage Fault Status (UFAULTSTAT) UNDEF Attempt to enter an invalid instruction Usage fault b set state Usage Fault Status (UFAULTSTAT) INVSTAT a Invalid EXC_RETURN value Usage fault Usage Fault Status (UFAULTSTAT) INVPC Illegal unaligned load or store Usage fault Usage Fault Status (UFAULTSTAT) UNALIGN Divide by 0 Usage fault Usage Fault Status (UFAULTSTAT) DIV0 a. Occurs on an access to an XN region even if the MPU is disabled. b. Attempting to use an instruction set other than the Thumb instruction set, or returning to a non load-store-multiple instruction with ICI continuation. 2.6.2 Fault Escalation and Hard Faults All fault exceptions except for hard fault have configurable exception priority (see SYSPRI1 on page 115). Software can disable execution of the handlers for these faults (see SYSHNDCTRL on page 118). Usually, the exception priority, together with the values of the exception mask registers, determines whether the processor enters the fault handler, and whether a fault handler can preempt another fault handler as described in “Exception Model” on page 67. In some situations, a fault with configurable priority is treated as a hard fault. This process is called priority escalation, and the fault is described as escalated to hard fault. Escalation to hard fault occurs when: July 14, 2014 75 Texas Instruments-Production Data The Cortex-M3 Processor ■ A fault handler causes the same kind of fault as the one it is servicing. This escalation to hard fault occurs because a fault handler cannot preempt itself because it must have the same priority as the current priority level. ■ A fault handler causes a fault with the same or lower priority as the fault it is servicing. This situation happens because the handler for the new fault cannot preempt the currently executing fault handler. ■ An exception handler causes a fault for which the priority is the same as or lower than the currently executing exception. ■ A fault occurs and the handler for that fault is not enabled. If a bus fault occurs during a stack push when entering a bus fault handler, the bus fault does not escalate to a hard fault. Thus if a corrupted stack causes a fault, the fault handler executes even though the stack push for the handler failed. The fault handler operates but the stack contents are corrupted. Note: 2.6.3 Only Reset and NMI can preempt the fixed priority hard fault. A hard fault can preempt any exception other than Reset, NMI, or another hard fault. Fault Status Registers and Fault Address Registers The fault status registers indicate the cause of a fault. For bus faults and memory management faults, the fault address register indicates the address accessed by the operation that caused the fault, as shown in Table 2-12 on page 76. Table 2-12. Fault Status and Fault Address Registers Handler Status Register Name Address Register Name Register Description Hard fault Hard Fault Status (HFAULTSTAT) - page 128 Memory management Memory Management Fault Status fault (MFAULTSTAT) Memory Management Fault Address (MMADDR) page 122 Bus fault Bus Fault Address (FAULTADDR) page 122 - page 122 Bus Fault Status (BFAULTSTAT) Usage fault 2.6.4 Usage Fault Status (UFAULTSTAT) page 129 page 130 Lockup The processor enters a lockup state if a hard fault occurs when executing the NMI or hard fault handlers. When the processor is in the lockup state, it does not execute any instructions. The processor remains in lockup state until it is reset, an NMI occurs, or it is halted by a debugger. Note: 2.7 If the lockup state occurs from the NMI handler, a subsequent NMI does not cause the processor to leave the lockup state. Power Management The Cortex-M3 processor sleep modes reduce power consumption: ■ Sleep mode stops the processor clock. ■ Deep-sleep mode stops the system clock and switches off the PLL and Flash memory. 76 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller The SLEEPDEEP bit of the System Control (SYSCTRL) register selects which sleep mode is used (see page 111). For more information about the behavior of the sleep modes, see “System Control” on page 158. This section describes the mechanisms for entering sleep mode and the conditions for waking up from sleep mode, both of which apply to Sleep mode and Deep-sleep mode. 2.7.1 Entering Sleep Modes This section describes the mechanisms software can use to put the processor into one of the sleep modes. The system can generate spurious wake-up events, for example a debug operation wakes up the processor. Therefore, software must be able to put the processor back into sleep mode after such an event. A program might have an idle loop to put the processor back to sleep mode. 2.7.1.1 Wait for Interrupt The wait for interrupt instruction, WFI, causes immediate entry to sleep mode unless the wake-up condition is true (see “Wake Up from WFI or Sleep-on-Exit” on page 77). When the processor executes a WFI instruction, it stops executing instructions and enters sleep mode. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. 2.7.1.2 Wait for Event The wait for event instruction, WFE, causes entry to sleep mode conditional on the value of a one-bit event register. When the processor executes a WFE instruction, it checks the event register. If the register is 0, the processor stops executing instructions and enters sleep mode. If the register is 1, the processor clears the register and continues executing instructions without entering sleep mode. If the event register is 1, the processor must not enter sleep mode on execution of a WFE instruction. Typically, this situation occurs if an SEV instruction has been executed. Software cannot access this register directly. See the Cortex™-M3/M4 Instruction Set Technical User's Manual for more information. 2.7.1.3 Sleep-on-Exit If the SLEEPEXIT bit of the SYSCTRL register is set, when the processor completes the execution of all exception handlers, it returns to Thread mode and immediately enters sleep mode. This mechanism can be used in applications that only require the processor to run when an exception occurs. 2.7.2 Wake Up from Sleep Mode The conditions for the processor to wake up depend on the mechanism that cause it to enter sleep mode. 2.7.2.1 Wake Up from WFI or Sleep-on-Exit Normally, the processor wakes up only when the NVIC detects an exception with sufficient priority to cause exception entry. Some embedded systems might have to execute system restore tasks after the processor wakes up and before executing an interrupt handler. Entry to the interrupt handler can be delayed by setting the PRIMASK bit and clearing the FAULTMASK bit. If an interrupt arrives that is enabled and has a higher priority than current exception priority, the processor wakes up but does not execute the interrupt handler until the processor clears PRIMASK. For more information about PRIMASK and FAULTMASK, see page 55 and page 56. July 14, 2014 77 Texas Instruments-Production Data The Cortex-M3 Processor 2.7.2.2 Wake Up from WFE The processor wakes up if it detects an exception with sufficient priority to cause exception entry. In addition, if the SEVONPEND bit in the SYSCTRL register is set, any new pending interrupt triggers an event and wakes up the processor, even if the interrupt is disabled or has insufficient priority to cause exception entry. For more information about SYSCTRL, see page 111. 2.8 Instruction Set Summary The processor implements a version of the Thumb instruction set. Table 2-13 on page 78 lists the supported instructions. Note: In Table 2-13 on page 78: ■ ■ ■ ■ ■ Angle brackets, , enclose alternative forms of the operand Braces, {}, enclose optional operands The Operands column is not exhaustive Op2 is a flexible second operand that can be either a register or a constant Most instructions can use an optional condition code suffix For more information on the instructions and operands, see the instruction descriptions in the Cortex™-M3/M4 Instruction Set Technical User's Manual. Table 2-13. Cortex-M3 Instruction Summary Mnemonic Operands Brief Description Flags ADC, ADCS {Rd,} Rn, Op2 Add with carry N,Z,C,V ADD, ADDS {Rd,} Rn, Op2 Add N,Z,C,V ADD, ADDW {Rd,} Rn , #imm12 Add N,Z,C,V ADR Rd, label Load PC-relative address - AND, ANDS {Rd,} Rn, Op2 Logical AND N,Z,C ASR, ASRS Rd, Rm, Arithmetic shift right N,Z,C B label Branch - BFC Rd, #lsb, #width Bit field clear - BFI Rd, Rn, #lsb, #width Bit field insert - BIC, BICS {Rd,} Rn, Op2 Bit clear N,Z,C BKPT #imm Breakpoint - BL label Branch with link - BLX Rm Branch indirect with link - BX Rm Branch indirect - CBNZ Rn, label Compare and branch if non-zero - CBZ Rn, label Compare and branch if zero - CLREX - Clear exclusive - CLZ Rd, Rm Count leading zeros - CMN Rn, Op2 Compare negative N,Z,C,V CMP Rn, Op2 Compare N,Z,C,V CPSID i Change processor state, disable interrupts - CPSIE i Change processor state, enable interrupts - 78 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 2-13. Cortex-M3 Instruction Summary (continued) Mnemonic Operands Brief Description Flags DMB - Data memory barrier - DSB - Data synchronization barrier - EOR, EORS {Rd,} Rn, Op2 Exclusive OR N,Z,C ISB - Instruction synchronization barrier - IT - If-Then condition block - LDM Rn{!}, reglist Load multiple registers, increment after - LDMDB, LDMEA Rn{!}, reglist Load multiple registers, decrement before LDMFD, LDMIA Rn{!}, reglist Load multiple registers, increment after - LDR Rt, [Rn, #offset] Load register with word - LDRB, LDRBT Rt, [Rn, #offset] Load register with byte - LDRD Rt, Rt2, [Rn, #offset] Load register with two bytes - LDREX Rt, [Rn, #offset] Load register exclusive - LDREXB Rt, [Rn] Load register exclusive with byte - LDREXH Rt, [Rn] Load register exclusive with halfword - LDRH, LDRHT Rt, [Rn, #offset] Load register with halfword - LDRSB, LDRSBT Rt, [Rn, #offset] Load register with signed byte - LDRSH, LDRSHT Rt, [Rn, #offset] Load register with signed halfword - LDRT Rt, [Rn, #offset] Load register with word - LSL, LSLS Rd, Rm, Logical shift left N,Z,C LSR, LSRS Rd, Rm, Logical shift right N,Z,C MLA Rd, Rn, Rm, Ra Multiply with accumulate, 32-bit result - MLS Rd, Rn, Rm, Ra Multiply and subtract, 32-bit result - MOV, MOVS Rd, Op2 Move N,Z,C MOV, MOVW Rd, #imm16 Move 16-bit constant N,Z,C MOVT Rd, #imm16 Move top - MRS Rd, spec_reg Move from special register to general register - MSR spec_reg, Rm Move from general register to special register N,Z,C,V MUL, MULS {Rd,} Rn, Rm Multiply, 32-bit result N,Z MVN, MVNS Rd, Op2 Move NOT N,Z,C NOP - No operation - ORN, ORNS {Rd,} Rn, Op2 Logical OR NOT N,Z,C ORR, ORRS {Rd,} Rn, Op2 Logical OR N,Z,C POP reglist Pop registers from stack - PUSH reglist Push registers onto stack - RBIT Rd, Rn Reverse bits - REV Rd, Rn Reverse byte order in a word - REV16 Rd, Rn Reverse byte order in each halfword - REVSH Rd, Rn Reverse byte order in bottom halfword and sign extend - July 14, 2014 - 79 Texas Instruments-Production Data The Cortex-M3 Processor Table 2-13. Cortex-M3 Instruction Summary (continued) Mnemonic Operands Brief Description Flags ROR, RORS Rd, Rm, Rotate right N,Z,C RRX, RRXS Rd, Rm Rotate right with extend N,Z,C RSB, RSBS {Rd,} Rn, Op2 Reverse subtract N,Z,C,V SBC, SBCS {Rd,} Rn, Op2 Subtract with carry N,Z,C,V SBFX Rd, Rn, #lsb, #width Signed bit field extract - SDIV {Rd,} Rn, Rm Signed divide - SEV - Send event - SMLAL RdLo, RdHi, Rn, Rm Signed multiply with accumulate (32x32+64), 64-bit result - SMULL RdLo, RdHi, Rn, Rm Signed multiply (32x32), 64-bit result - SSAT Rd, #n, Rm {,shift #s} Signed saturate Q STM Rn{!}, reglist Store multiple registers, increment after - STMDB, STMEA Rn{!}, reglist Store multiple registers, decrement before STMFD, STMIA Rn{!}, reglist Store multiple registers, increment after - STR Rt, [Rn {, #offset}] Store register word - STRB, STRBT Rt, [Rn {, #offset}] Store register byte - STRD Rt, Rt2, [Rn {, #offset}] Store register two words - STREX Rt, Rt, [Rn {, #offset}] Store register exclusive - STREXB Rd, Rt, [Rn] Store register exclusive byte - STREXH Rd, Rt, [Rn] Store register exclusive halfword - STRH, STRHT Rt, [Rn {, #offset}] Store register halfword - STRSB, STRSBT Rt, [Rn {, #offset}] Store register signed byte - STRSH, STRSHT Rt, [Rn {, #offset}] Store register signed halfword - STRT Rt, [Rn {, #offset}] Store register word - SUB, SUBS {Rd,} Rn, Op2 Subtract N,Z,C,V SUB, SUBW {Rd,} Rn, #imm12 Subtract 12-bit constant N,Z,C,V SVC #imm Supervisor call - SXTB {Rd,} Rm {,ROR #n} Sign extend a byte - SXTH {Rd,} Rm {,ROR #n} Sign extend a halfword - TBB [Rn, Rm] Table branch byte - TBH [Rn, Rm, LSL #1] Table branch halfword - TEQ Rn, Op2 Test equivalence N,Z,C TST Rn, Op2 Test N,Z,C UBFX Rd, Rn, #lsb, #width Unsigned bit field extract - UDIV {Rd,} Rn, Rm Unsigned divide - UMLAL RdLo, RdHi, Rn, Rm Unsigned multiply with accumulate (32x32+32+32), 64-bit result - UMULL RdLo, RdHi, Rn, Rm Unsigned multiply (32x 2), 64-bit result - USAT Rd, #n, Rm {,shift #s} Unsigned Saturate Q UXTB {Rd,} Rm, {,ROR #n} Zero extend a Byte - UXTH {Rd,} Rm, {,ROR #n} Zero extend a Halfword - 80 - July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 2-13. Cortex-M3 Instruction Summary (continued) Mnemonic Operands Brief Description Flags WFE - Wait for event - WFI - Wait for interrupt - July 14, 2014 81 Texas Instruments-Production Data Cortex-M3 Peripherals 3 Cortex-M3 Peripherals ® This chapter provides information on the Stellaris implementation of the Cortex-M3 processor peripherals, including: ■ SysTick (see page 82) Provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. ■ Nested Vectored Interrupt Controller (NVIC) (see page 83) – Facilitates low-latency exception and interrupt handling – Controls power management – Implements system control registers ■ System Control Block (SCB) (see page 85) Provides system implementation information and system control, including configuration, control, and reporting of system exceptions. ■ Memory Protection Unit (MPU) (see page 85) Supports the standard ARMv7 Protected Memory System Architecture (PMSA) model. The MPU provides full support for protection regions, overlapping protection regions, access permissions, and exporting memory attributes to the system. Table 3-1 on page 82 shows the address map of the Private Peripheral Bus (PPB). Some peripheral register regions are split into two address regions, as indicated by two addresses listed. Table 3-1. Core Peripheral Register Regions Address Core Peripheral Description (see page ...) 0xE000.E010-0xE000.E01F System Timer 82 0xE000.E100-0xE000.E4EF Nested Vectored Interrupt Controller 83 0xE000.ED00-0xE000.ED3F System Control Block 85 0xE000.ED90-0xE000.EDB8 Memory Protection Unit 85 0xE000.EF00-0xE000.EF03 3.1 Functional Description This chapter provides information on the Stellaris implementation of the Cortex-M3 processor peripherals: SysTick, NVIC, SCB and MPU. 3.1.1 System Timer (SysTick) Cortex-M3 includes an integrated system timer, SysTick, which provides a simple, 24-bit clear-on-write, decrementing, wrap-on-zero counter with a flexible control mechanism. The counter can be used in several different ways, for example as: ■ An RTOS tick timer that fires at a programmable rate (for example, 100 Hz) and invokes a SysTick routine. ■ A high-speed alarm timer using the system clock. 82 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ A variable rate alarm or signal timer—the duration is range-dependent on the reference clock used and the dynamic range of the counter. ■ A simple counter used to measure time to completion and time used. ■ An internal clock source control based on missing/meeting durations. The COUNT bit in the STCTRL control and status register can be used to determine if an action completed within a set duration, as part of a dynamic clock management control loop. The timer consists of three registers: ■ SysTick Control and Status (STCTRL): A control and status counter to configure its clock, enable the counter, enable the SysTick interrupt, and determine counter status. ■ SysTick Reload Value (STRELOAD): The reload value for the counter, used to provide the counter's wrap value. ■ SysTick Current Value (STCURRENT): The current value of the counter. When enabled, the timer counts down on each clock from the reload value to zero, reloads (wraps) to the value in the STRELOAD register on the next clock edge, then decrements on subsequent clocks. Clearing the STRELOAD register disables the counter on the next wrap. When the counter reaches zero, the COUNT status bit is set. The COUNT bit clears on reads. Writing to the STCURRENT register clears the register and the COUNT status bit. The write does not trigger the SysTick exception logic. On a read, the current value is the value of the register at the time the register is accessed. The SysTick counter runs on the system clock. If this clock signal is stopped for low power mode, the SysTick counter stops. Ensure software uses aligned word accesses to access the SysTick registers. Note: 3.1.2 When the processor is halted for debugging, the counter does not decrement. Nested Vectored Interrupt Controller (NVIC) This section describes the Nested Vectored Interrupt Controller (NVIC) and the registers it uses. The NVIC supports: ■ 21 interrupts. ■ A programmable priority level of 0-7 for each interrupt. A higher level corresponds to a lower priority, so level 0 is the highest interrupt priority. ■ Low-latency exception and interrupt handling. ■ Level and pulse detection of interrupt signals. ■ Dynamic reprioritization of interrupts. ■ Grouping of priority values into group priority and subpriority fields. ■ Interrupt tail-chaining. ■ An external Non-maskable interrupt (NMI). July 14, 2014 83 Texas Instruments-Production Data Cortex-M3 Peripherals The processor automatically stacks its state on exception entry and unstacks this state on exception exit, with no instruction overhead, providing low latency exception handling. 3.1.2.1 Level-Sensitive and Pulse Interrupts The processor supports both level-sensitive and pulse interrupts. Pulse interrupts are also described as edge-triggered interrupts. A level-sensitive interrupt is held asserted until the peripheral deasserts the interrupt signal. Typically this happens because the ISR accesses the peripheral, causing it to clear the interrupt request. A pulse interrupt is an interrupt signal sampled synchronously on the rising edge of the processor clock. To ensure the NVIC detects the interrupt, the peripheral must assert the interrupt signal for at least one clock cycle, during which the NVIC detects the pulse and latches the interrupt. When the processor enters the ISR, it automatically removes the pending state from the interrupt (see “Hardware and Software Control of Interrupts” on page 84 for more information). For a level-sensitive interrupt, if the signal is not deasserted before the processor returns from the ISR, the interrupt becomes pending again, and the processor must execute its ISR again. As a result, the peripheral can hold the interrupt signal asserted until it no longer needs servicing. 3.1.2.2 Hardware and Software Control of Interrupts The Cortex-M3 latches all interrupts. A peripheral interrupt becomes pending for one of the following reasons: ■ The NVIC detects that the interrupt signal is High and the interrupt is not active. ■ The NVIC detects a rising edge on the interrupt signal. ■ Software writes to the corresponding interrupt set-pending register bit, or to the Software Trigger Interrupt (SWTRIG) register to make a Software-Generated Interrupt pending. See the INT bit in the PEND0 register on page 98 or SWTRIG on page 103. A pending interrupt remains pending until one of the following: ■ The processor enters the ISR for the interrupt, changing the state of the interrupt from pending to active. Then: – For a level-sensitive interrupt, when the processor returns from the ISR, the NVIC samples the interrupt signal. If the signal is asserted, the state of the interrupt changes to pending, which might cause the processor to immediately re-enter the ISR. Otherwise, the state of the interrupt changes to inactive. – For a pulse interrupt, the NVIC continues to monitor the interrupt signal, and if this is pulsed the state of the interrupt changes to pending and active. In this case, when the processor returns from the ISR the state of the interrupt changes to pending, which might cause the processor to immediately re-enter the ISR. If the interrupt signal is not pulsed while the processor is in the ISR, when the processor returns from the ISR the state of the interrupt changes to inactive. ■ Software writes to the corresponding interrupt clear-pending register bit – For a level-sensitive interrupt, if the interrupt signal is still asserted, the state of the interrupt does not change. Otherwise, the state of the interrupt changes to inactive. 84 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller – For a pulse interrupt, the state of the interrupt changes to inactive, if the state was pending or to active, if the state was active and pending. 3.1.3 System Control Block (SCB) The System Control Block (SCB) provides system implementation information and system control, including configuration, control, and reporting of the system exceptions. 3.1.4 Memory Protection Unit (MPU) This section describes the Memory protection unit (MPU). The MPU divides the memory map into a number of regions and defines the location, size, access permissions, and memory attributes of each region. The MPU supports independent attribute settings for each region, overlapping regions, and export of memory attributes to the system. The memory attributes affect the behavior of memory accesses to the region. The Cortex-M3 MPU defines eight separate memory regions, 0-7, and a background region. When memory regions overlap, a memory access is affected by the attributes of the region with the highest number. For example, the attributes for region 7 take precedence over the attributes of any region that overlaps region 7. The background region has the same memory access attributes as the default memory map, but is accessible from privileged software only. The Cortex-M3 MPU memory map is unified, meaning that instruction accesses and data accesses have the same region settings. If a program accesses a memory location that is prohibited by the MPU, the processor generates a memory management fault, causing a fault exception and possibly causing termination of the process in an OS environment. In an OS environment, the kernel can update the MPU region setting dynamically based on the process to be executed. Typically, an embedded OS uses the MPU for memory protection. Configuration of MPU regions is based on memory types (see “Memory Regions, Types and Attributes” on page 60 for more information). Table 3-2 on page 85 shows the possible MPU region attributes. See the section called “MPU Configuration for a Stellaris Microcontroller” on page 89 for guidelines for programming a microcontroller implementation. Table 3-2. Memory Attributes Summary Memory Type Description Strongly Ordered All accesses to Strongly Ordered memory occur in program order. Device Memory-mapped peripherals Normal Normal memory To avoid unexpected behavior, disable the interrupts before updating the attributes of a region that the interrupt handlers might access. Ensure software uses aligned accesses of the correct size to access MPU registers: ■ Except for the MPU Region Attribute and Size (MPUATTR) register, all MPU registers must be accessed with aligned word accesses. ■ The MPUATTR register can be accessed with byte or aligned halfword or word accesses. July 14, 2014 85 Texas Instruments-Production Data Cortex-M3 Peripherals The processor does not support unaligned accesses to MPU registers. When setting up the MPU, and if the MPU has previously been programmed, disable unused regions to prevent any previous region settings from affecting the new MPU setup. 3.1.4.1 Updating an MPU Region To update the attributes for an MPU region, the MPU Region Number (MPUNUMBER), MPU Region Base Address (MPUBASE) and MPUATTR registers must be updated. Each register can be programmed separately or with a multiple-word write to program all of these registers. You can use the MPUBASEx and MPUATTRx aliases to program up to four regions simultaneously using an STM instruction. Updating an MPU Region Using Separate Words This example simple code configures one region: ; R1 = region number ; R2 = size/enable ; R3 = attributes ; R4 = address LDR R0,=MPUNUMBER STR R1, [R0, #0x0] STR R4, [R0, #0x4] STRH R2, [R0, #0x8] STRH R3, [R0, #0xA] ; ; ; ; ; 0xE000ED98, MPU region number register Region Number Region Base Address Region Size and Enable Region Attribute Disable a region before writing new region settings to the MPU if you have previously enabled the region being changed. For example: ; R1 = region number ; R2 = size/enable ; R3 = attributes ; R4 = address LDR R0,=MPUNUMBER STR R1, [R0, #0x0] BIC R2, R2, #1 STRH R2, [R0, #0x8] STR R4, [R0, #0x4] STRH R3, [R0, #0xA] ORR R2, #1 STRH R2, [R0, #0x8] ; ; ; ; ; ; ; ; 0xE000ED98, MPU region number register Region Number Disable Region Size and Enable Region Base Address Region Attribute Enable Region Size and Enable Software must use memory barrier instructions: ■ Before MPU setup, if there might be outstanding memory transfers, such as buffered writes, that might be affected by the change in MPU settings. ■ After MPU setup, if it includes memory transfers that must use the new MPU settings. However, memory barrier instructions are not required if the MPU setup process starts by entering an exception handler, or is followed by an exception return, because the exception entry and exception return mechanism cause memory barrier behavior. Software does not need any memory barrier instructions during MPU setup, because it accesses the MPU through the Private Peripheral Bus (PPB), which is a Strongly Ordered memory region. 86 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller For example, if all of the memory access behavior is intended to take effect immediately after the programming sequence, then a DSB instruction and an ISB instruction should be used. A DSB is required after changing MPU settings, such as at the end of context switch. An ISB is required if the code that programs the MPU region or regions is entered using a branch or call. If the programming sequence is entered using a return from exception, or by taking an exception, then an ISB is not required. Updating an MPU Region Using Multi-Word Writes The MPU can be programmed directly using multi-word writes, depending how the information is divided. Consider the following reprogramming: ; R1 = region number ; R2 = address ; R3 = size, attributes in one LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register STR R1, [R0, #0x0] ; Region Number STR R2, [R0, #0x4] ; Region Base Address STR R3, [R0, #0x8] ; Region Attribute, Size and Enable An STM instruction can be used to optimize this: ; R1 = region number ; R2 = address ; R3 = size, attributes in one LDR R0, =MPUNUMBER ; 0xE000ED98, MPU region number register STM R0, {R1-R3} ; Region number, address, attribute, size and enable This operation can be done in two words for pre-packed information, meaning that the MPU Region Base Address (MPUBASE) register (see page 135) contains the required region number and has the VALID bit set. This method can be used when the data is statically packed, for example in a boot loader: ; R1 = address and region number in one ; R2 = size and attributes in one LDR R0, =MPUBASE ; 0xE000ED9C, MPU Region Base register STR R1, [R0, #0x0] ; Region base address and region number combined ; with VALID (bit 4) set STR R2, [R0, #0x4] ; Region Attribute, Size and Enable Subregions Regions of 256 bytes or more are divided into eight equal-sized subregions. Set the corresponding bit in the SRD field of the MPU Region Attribute and Size (MPUATTR) register (see page 137) to disable a subregion. The least-significant bit of the SRD field controls the first subregion, and the most-significant bit controls the last subregion. Disabling a subregion means another region overlapping the disabled range matches instead. If no other enabled region overlaps the disabled subregion, the MPU issues a fault. Regions of 32, 64, and 128 bytes do not support subregions. With regions of these sizes, the SRD field must be configured to 0x00, otherwise the MPU behavior is unpredictable. July 14, 2014 87 Texas Instruments-Production Data Cortex-M3 Peripherals Example of SRD Use Two regions with the same base address overlap. Region one is 128 KB, and region two is 512 KB. To ensure the attributes from region one apply to the first 128 KB region, configure the SRD field for region two to 0x03 to disable the first two subregions, as Figure 3-1 on page 88 shows. Figure 3-1. SRD Use Example Region 2, with subregions Region 1 Base address of both regions 3.1.4.2 Offset from base address 512KB 448KB 384KB 320KB 256KB 192KB 128KB Disabled subregion 64KB Disabled subregion 0 MPU Access Permission Attributes The access permission bits, TEX, S, C, B, AP, and XN of the MPUATTR register, control access to the corresponding memory region. If an access is made to an area of memory without the required permissions, then the MPU generates a permission fault. Table 3-3 on page 88 shows the encodings for the TEX, C, B, and S access permission bits. All encodings are shown for completeness, however the current implementation of the Cortex-M3 does not support the concept of cacheability or shareability. Refer to the section called “MPU Configuration for a Stellaris Microcontroller” on page 89 for information on programming the MPU for Stellaris implementations. Table 3-3. TEX, S, C, and B Bit Field Encoding TEX S 000b x C B Memory Type Shareability Other Attributes a 0 0 Strongly Ordered Shareable - a - 000 x 0 1 Device Shareable 000 0 1 0 Normal Not shareable 000 1 1 0 Normal Shareable 000 0 1 1 Normal Not shareable 000 1 1 1 Normal Shareable 001 0 0 0 Normal Not shareable 001 1 0 0 Normal Shareable Outer and inner noncacheable. 001 x a 0 1 Reserved encoding - - a Outer and inner write-through. No write allocate. 001 x 1 0 Reserved encoding - - 001 0 1 1 Normal Not shareable 001 1 1 1 Normal Shareable Outer and inner write-back. Write and read allocate. 010 x a 0 0 Device Not shareable Nonshared Device. a 0 1 Reserved encoding - - a 1 x Reserved encoding - - 010 x 010 x a 88 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 3-3. TEX, S, C, and B Bit Field Encoding (continued) TEX S C B Memory Type Shareability Other Attributes 1BB 0 A A Normal Not shareable 1BB 1 A A Normal Shareable Cached memory (BB = outer policy, AA = inner policy). See Table 3-4 for the encoding of the AA and BB bits. a. The MPU ignores the value of this bit. Table 3-4 on page 89 shows the cache policy for memory attribute encodings with a TEX value in the range of 0x4-0x7. Table 3-4. Cache Policy for Memory Attribute Encoding Encoding, AA or BB Corresponding Cache Policy 00 Non-cacheable 01 Write back, write and read allocate 10 Write through, no write allocate 11 Write back, no write allocate Table 3-5 on page 89 shows the AP encodings in the MPUATTR register that define the access permissions for privileged and unprivileged software. Table 3-5. AP Bit Field Encoding AP Bit Field Privileged Permissions Unprivileged Permissions Description 000 No access No access All accesses generate a permission fault. 001 R/W No access Access from privileged software only. 010 R/W RO Writes by unprivileged software generate a permission fault. 011 R/W R/W Full access. 100 Unpredictable Unpredictable Reserved. 101 RO No access Reads by privileged software only. 110 RO RO Read-only, by privileged or unprivileged software. 111 RO RO Read-only, by privileged or unprivileged software. MPU Configuration for a Stellaris Microcontroller Stellaris microcontrollers have only a single processor and no caches. As a result, the MPU should be programmed as shown in Table 3-6 on page 89. Table 3-6. Memory Region Attributes for Stellaris Microcontrollers Memory Region TEX S C B Memory Type and Attributes Flash memory 000b 0 1 0 Normal memory, non-shareable, write-through Internal SRAM 000b 1 1 0 Normal memory, shareable, write-through External SRAM 000b 1 1 1 Normal memory, shareable, write-back, write-allocate Peripherals 000b 1 0 1 Device memory, shareable July 14, 2014 89 Texas Instruments-Production Data Cortex-M3 Peripherals In current Stellaris microcontroller implementations, the shareability and cache policy attributes do not affect the system behavior. However, using these settings for the MPU regions can make the application code more portable. The values given are for typical situations. 3.1.4.3 MPU Mismatch When an access violates the MPU permissions, the processor generates a memory management fault (see “Exceptions and Interrupts” on page 59 for more information). The MFAULTSTAT register indicates the cause of the fault. See page 122 for more information. 3.2 Register Map Table 3-7 on page 90 lists the Cortex-M3 Peripheral SysTick, NVIC, MPU and SCB registers. The offset listed is a hexadecimal increment to the register's address, relative to the Core Peripherals base address of 0xE000.E000. Note: Register spaces that are not used are reserved for future or internal use. Software should not modify any reserved memory address. Table 3-7. Peripherals Register Map Offset Name Type Reset Description See page System Timer (SysTick) Registers 0x010 STCTRL R/W 0x0000.0000 SysTick Control and Status Register 92 0x014 STRELOAD R/W 0x0000.0000 SysTick Reload Value Register 94 0x018 STCURRENT R/WC 0x0000.0000 SysTick Current Value Register 95 Nested Vectored Interrupt Controller (NVIC) Registers 0x100 EN0 R/W 0x0000.0000 Interrupt 0-29 Set Enable 96 0x180 DIS0 R/W 0x0000.0000 Interrupt 0-29 Clear Enable 97 0x200 PEND0 R/W 0x0000.0000 Interrupt 0-29 Set Pending 98 0x280 UNPEND0 R/W 0x0000.0000 Interrupt 0-29 Clear Pending 99 0x300 ACTIVE0 RO 0x0000.0000 Interrupt 0-29 Active Bit 100 0x400 PRI0 R/W 0x0000.0000 Interrupt 0-3 Priority 101 0x404 PRI1 R/W 0x0000.0000 Interrupt 4-7 Priority 101 0x408 PRI2 R/W 0x0000.0000 Interrupt 8-11 Priority 101 0x40C PRI3 R/W 0x0000.0000 Interrupt 12-15 Priority 101 0x410 PRI4 R/W 0x0000.0000 Interrupt 16-19 Priority 101 0x414 PRI5 R/W 0x0000.0000 Interrupt 20-23 Priority 101 0x418 PRI6 R/W 0x0000.0000 Interrupt 24-27 Priority 101 0x41C PRI7 R/W 0x0000.0000 Interrupt 28-29 Priority 101 0xF00 SWTRIG WO 0x0000.0000 Software Trigger Interrupt 103 90 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 3-7. Peripherals Register Map (continued) Offset Name Type Reset Description See page System Control Block (SCB) Registers 0xD00 CPUID RO 0x410F.C231 CPU ID Base 104 0xD04 INTCTRL R/W 0x0000.0000 Interrupt Control and State 105 0xD08 VTABLE R/W 0x0000.0000 Vector Table Offset 108 0xD0C APINT R/W 0xFA05.0000 Application Interrupt and Reset Control 109 0xD10 SYSCTRL R/W 0x0000.0000 System Control 111 0xD14 CFGCTRL R/W 0x0000.0000 Configuration and Control 113 0xD18 SYSPRI1 R/W 0x0000.0000 System Handler Priority 1 115 0xD1C SYSPRI2 R/W 0x0000.0000 System Handler Priority 2 116 0xD20 SYSPRI3 R/W 0x0000.0000 System Handler Priority 3 117 0xD24 SYSHNDCTRL R/W 0x0000.0000 System Handler Control and State 118 0xD28 FAULTSTAT R/W1C 0x0000.0000 Configurable Fault Status 122 0xD2C HFAULTSTAT R/W1C 0x0000.0000 Hard Fault Status 128 0xD34 MMADDR R/W - Memory Management Fault Address 129 0xD38 FAULTADDR R/W - Bus Fault Address 130 Memory Protection Unit (MPU) Registers 0xD90 MPUTYPE RO 0x0000.0800 MPU Type 131 0xD94 MPUCTRL R/W 0x0000.0000 MPU Control 132 0xD98 MPUNUMBER R/W 0x0000.0000 MPU Region Number 134 0xD9C MPUBASE R/W 0x0000.0000 MPU Region Base Address 135 0xDA0 MPUATTR R/W 0x0000.0000 MPU Region Attribute and Size 137 0xDA4 MPUBASE1 R/W 0x0000.0000 MPU Region Base Address Alias 1 135 0xDA8 MPUATTR1 R/W 0x0000.0000 MPU Region Attribute and Size Alias 1 137 0xDAC MPUBASE2 R/W 0x0000.0000 MPU Region Base Address Alias 2 135 0xDB0 MPUATTR2 R/W 0x0000.0000 MPU Region Attribute and Size Alias 2 137 0xDB4 MPUBASE3 R/W 0x0000.0000 MPU Region Base Address Alias 3 135 0xDB8 MPUATTR3 R/W 0x0000.0000 MPU Region Attribute and Size Alias 3 137 3.3 System Timer (SysTick) Register Descriptions This section lists and describes the System Timer registers, in numerical order by address offset. July 14, 2014 91 Texas Instruments-Production Data Cortex-M3 Peripherals Register 1: SysTick Control and Status Register (STCTRL), offset 0x010 Note: This register can only be accessed from privileged mode. The SysTick STCTRL register enables the SysTick features. SysTick Control and Status Register (STCTRL) Base 0xE000.E000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 16 COUNT RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 2 1 0 CLK_SRC INTEN ENABLE R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:17 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 16 COUNT RO 0 Count Flag Value Description 0 The SysTick timer has not counted to 0 since the last time this bit was read. 1 The SysTick timer has counted to 0 since the last time this bit was read. This bit is cleared by a read of the register or if the STCURRENT register is written with any value. If read by the debugger using the DAP, this bit is cleared only if the MasterType bit in the AHB-AP Control Register is clear. Otherwise, the COUNT bit is not changed by the debugger read. See the ARM® Debug Interface V5 Architecture Specification for more information on MasterType. 15:3 reserved RO 0x000 2 CLK_SRC R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Clock Source Value Description 0 External reference clock. (Not implemented for most Stellaris microcontrollers.) 1 System clock Because an external reference clock is not implemented, this bit must be set in order for SysTick to operate. 92 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 1 INTEN R/W 0 0 ENABLE R/W 0 Description Interrupt Enable Value Description 0 Interrupt generation is disabled. Software can use the COUNT bit to determine if the counter has ever reached 0. 1 An interrupt is generated to the NVIC when SysTick counts to 0. Enable Value Description 0 The counter is disabled. 1 Enables SysTick to operate in a multi-shot way. That is, the counter loads the RELOAD value and begins counting down. On reaching 0, the COUNT bit is set and an interrupt is generated if enabled by INTEN. The counter then loads the RELOAD value again and begins counting. July 14, 2014 93 Texas Instruments-Production Data Cortex-M3 Peripherals Register 2: SysTick Reload Value Register (STRELOAD), offset 0x014 Note: This register can only be accessed from privileged mode. The STRELOAD register specifies the start value to load into the SysTick Current Value (STCURRENT) register when the counter reaches 0. The start value can be between 0x1 and 0x00FF.FFFF. A start value of 0 is possible but has no effect because the SysTick interrupt and the COUNT bit are activated when counting from 1 to 0. SysTick can be configured as a multi-shot timer, repeated over and over, firing every N+1 clock pulses, where N is any value from 1 to 0x00FF.FFFF. For example, if a tick interrupt is required every 100 clock pulses, 99 must be written into the RELOAD field. SysTick Reload Value Register (STRELOAD) Base 0xE000.E000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 RO 0 RO 0 RO 0 RO 0 15 14 13 R/W 0 R/W 0 R/W 0 27 26 25 24 23 22 21 20 18 17 16 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset 19 RELOAD RELOAD Type Reset Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:0 RELOAD R/W 0x00.0000 Reload Value Value to load into the SysTick Current Value (STCURRENT) register when the counter reaches 0. 94 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 3: SysTick Current Value Register (STCURRENT), offset 0x018 Note: This register can only be accessed from privileged mode. The STCURRENT register contains the current value of the SysTick counter. SysTick Current Value Register (STCURRENT) Base 0xE000.E000 Offset 0x018 Type R/WC, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 reserved Type Reset 20 19 18 17 16 CURRENT RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 CURRENT Type Reset R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 R/WC 0 Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:0 CURRENT R/WC 0x00.0000 Current Value This field contains the current value at the time the register is accessed. No read-modify-write protection is provided, so change with care. This register is write-clear. Writing to it with any value clears the register. Clearing this register also clears the COUNT bit of the STCTRL register. 3.4 NVIC Register Descriptions This section lists and describes the NVIC registers, in numerical order by address offset. The NVIC registers can only be fully accessed from privileged mode, but interrupts can be pended while in unprivileged mode by enabling the Configuration and Control (CFGCTRL) register. Any other unprivileged mode access causes a bus fault. Ensure software uses correctly aligned register accesses. The processor does not support unaligned accesses to NVIC registers. An interrupt can enter the pending state even if it is disabled. Before programming the VTABLE register to relocate the vector table, ensure the vector table entries of the new vector table are set up for fault handlers, NMI, and all enabled exceptions such as interrupts. For more information, see page 108. July 14, 2014 95 Texas Instruments-Production Data Cortex-M3 Peripherals Register 4: Interrupt 0-29 Set Enable (EN0), offset 0x100 Note: This register can only be accessed from privileged mode. The EN0 register enables interrupts and shows which interrupts are enabled. Bit 0 corresponds to Interrupt 0; bit 29 corresponds to Interrupt 29. See Table 2-9 on page 70 for interrupt assignments. If a pending interrupt is enabled, the NVIC activates the interrupt based on its priority. If an interrupt is not enabled, asserting its interrupt signal changes the interrupt state to pending, but the NVIC never activates the interrupt, regardless of its priority. Interrupt 0-29 Set Enable (EN0) Base 0xE000.E000 Offset 0x100 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset INT RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 INT Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:30 reserved RO 0x0 29:0 INT R/W 0x000.0000 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt Enable Value Description 0 On a read, indicates the interrupt is disabled. On a write, no effect. 1 On a read, indicates the interrupt is enabled. On a write, enables the interrupt. A bit can only be cleared by setting the corresponding INT[n] bit in the DISn register. 96 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: Interrupt 0-29 Clear Enable (DIS0), offset 0x180 Note: This register can only be accessed from privileged mode. The DIS0 register disables interrupts. Bit 0 corresponds to Interrupt 0; bit 29 corresponds to Interrupt 29. See Table 2-9 on page 70 for interrupt assignments. Interrupt 0-29 Clear Enable (DIS0) Base 0xE000.E000 Offset 0x180 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 reserved Type Reset 22 21 20 19 18 17 16 INT RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 INT Type Reset Bit/Field Name Type Reset 31:30 reserved RO 0x0 29:0 INT R/W 0x000.0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt Disable Value Description 0 On a read, indicates the interrupt is disabled. On a write, no effect. 1 On a read, indicates the interrupt is enabled. On a write, clears the corresponding INT[n] bit in the EN0 register, disabling interrupt [n]. July 14, 2014 97 Texas Instruments-Production Data Cortex-M3 Peripherals Register 6: Interrupt 0-29 Set Pending (PEND0), offset 0x200 Note: This register can only be accessed from privileged mode. The PEND0 register forces interrupts into the pending state and shows which interrupts are pending. Bit 0 corresponds to Interrupt 0; bit 29 corresponds to Interrupt 29. See Table 2-9 on page 70 for interrupt assignments. Interrupt 0-29 Set Pending (PEND0) Base 0xE000.E000 Offset 0x200 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 reserved Type Reset 22 21 20 19 18 17 16 INT RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 INT Type Reset Bit/Field Name Type Reset 31:30 reserved RO 0x0 29:0 INT R/W 0x000.0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt Set Pending Value Description 0 On a read, indicates that the interrupt is not pending. On a write, no effect. 1 On a read, indicates that the interrupt is pending. On a write, the corresponding interrupt is set to pending even if it is disabled. If the corresponding interrupt is already pending, setting a bit has no effect. A bit can only be cleared by setting the corresponding INT[n] bit in the UNPEND0 register. 98 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 7: Interrupt 0-29 Clear Pending (UNPEND0), offset 0x280 Note: This register can only be accessed from privileged mode. The UNPEND0 register shows which interrupts are pending and removes the pending state from interrupts. Bit 0 corresponds to Interrupt 0; bit 29 corresponds to Interrupt 29. See Table 2-9 on page 70 for interrupt assignments. Interrupt 0-29 Clear Pending (UNPEND0) Base 0xE000.E000 Offset 0x280 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 reserved Type Reset 22 21 20 19 18 17 16 INT RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 INT Type Reset Bit/Field Name Type Reset 31:30 reserved RO 0x0 29:0 INT R/W 0x000.0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt Clear Pending Value Description 0 On a read, indicates that the interrupt is not pending. On a write, no effect. 1 On a read, indicates that the interrupt is pending. On a write, clears the corresponding INT[n] bit in the PEND0 register, so that interrupt [n] is no longer pending. Setting a bit does not affect the active state of the corresponding interrupt. July 14, 2014 99 Texas Instruments-Production Data Cortex-M3 Peripherals Register 8: Interrupt 0-29 Active Bit (ACTIVE0), offset 0x300 Note: This register can only be accessed from privileged mode. The ACTIVE0 register indicates which interrupts are active. Bit 0 corresponds to Interrupt 0; bit 29 corresponds to Interrupt 29. See Table 2-9 on page 70 for interrupt assignments. Caution – Do not manually set or clear the bits in this register. Interrupt 0-29 Active Bit (ACTIVE0) Base 0xE000.E000 Offset 0x300 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 reserved Type Reset 22 21 20 19 18 17 16 INT RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 INT Type Reset Bit/Field Name Type Reset 31:30 reserved RO 0x0 29:0 INT RO 0x000.0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt Active Value Description 0 The corresponding interrupt is not active. 1 The corresponding interrupt is active, or active and pending. 100 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 9: Interrupt 0-3 Priority (PRI0), offset 0x400 Register 10: Interrupt 4-7 Priority (PRI1), offset 0x404 Register 11: Interrupt 8-11 Priority (PRI2), offset 0x408 Register 12: Interrupt 12-15 Priority (PRI3), offset 0x40C Register 13: Interrupt 16-19 Priority (PRI4), offset 0x410 Register 14: Interrupt 20-23 Priority (PRI5), offset 0x414 Register 15: Interrupt 24-27 Priority (PRI6), offset 0x418 Register 16: Interrupt 28-29 Priority (PRI7), offset 0x41C Note: This register can only be accessed from privileged mode. The PRIn registers provide 3-bit priority fields for each interrupt. These registers are byte accessible. Each register holds four priority fields that are assigned to interrupts as follows: PRIn Register Bit Field Interrupt Bits 31:29 Interrupt [4n+3] Bits 23:21 Interrupt [4n+2] Bits 15:13 Interrupt [4n+1] Bits 7:5 Interrupt [4n] See Table 2-9 on page 70 for interrupt assignments. Each priority level can be split into separate group priority and subpriority fields. The PRIGROUP field in the Application Interrupt and Reset Control (APINT) register (see page 109) indicates the position of the binary point that splits the priority and subpriority fields. These registers can only be accessed from privileged mode. Interrupt 0-3 Priority (PRI0) Base 0xE000.E000 Offset 0x400 Type R/W, reset 0x0000.0000 31 30 29 28 27 INTD Type Reset R/W 0 R/W 0 R/W 0 RO 0 RO 0 14 13 12 11 15 INTB Type Reset R/W 0 R/W 0 26 25 24 23 reserved RO 0 RO 0 RO 0 R/W 0 10 9 8 7 reserved R/W 0 RO 0 RO 0 RO 0 22 21 20 19 INTC R/W 0 R/W 0 RO 0 RO 0 6 5 4 3 INTA RO 0 Bit/Field Name Type Reset 31:29 INTD R/W 0x0 RO 0 R/W 0 R/W 0 18 17 16 RO 0 RO 0 RO 0 2 1 0 RO 0 RO 0 reserved reserved R/W 0 RO 0 RO 0 RO 0 Description Interrupt Priority for Interrupt [4n+3] This field holds a priority value, 0-7, for the interrupt with the number [4n+3], where n is the number of the Interrupt Priority register (n=0 for PRI0, and so on). The lower the value, the greater the priority of the corresponding interrupt. July 14, 2014 101 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset Description 28:24 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:21 INTC R/W 0x0 Interrupt Priority for Interrupt [4n+2] This field holds a priority value, 0-7, for the interrupt with the number [4n+2], where n is the number of the Interrupt Priority register (n=0 for PRI0, and so on). The lower the value, the greater the priority of the corresponding interrupt. 20:16 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:13 INTB R/W 0x0 Interrupt Priority for Interrupt [4n+1] This field holds a priority value, 0-7, for the interrupt with the number [4n+1], where n is the number of the Interrupt Priority register (n=0 for PRI0, and so on). The lower the value, the greater the priority of the corresponding interrupt. 12:8 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:5 INTA R/W 0x0 Interrupt Priority for Interrupt [4n] This field holds a priority value, 0-7, for the interrupt with the number [4n], where n is the number of the Interrupt Priority register (n=0 for PRI0, and so on). The lower the value, the greater the priority of the corresponding interrupt. 4:0 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 102 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: Software Trigger Interrupt (SWTRIG), offset 0xF00 Note: Only privileged software can enable unprivileged access to the SWTRIG register. Writing an interrupt number to the SWTRIG register generates a Software Generated Interrupt (SGI). See Table 2-9 on page 70 for interrupt assignments. When the MAINPEND bit in the Configuration and Control (CFGCTRL) register (see page 113) is set, unprivileged software can access the SWTRIG register. Software Trigger Interrupt (SWTRIG) Base 0xE000.E000 Offset 0xF00 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 WO 0 WO 0 WO 0 WO 0 reserved Type Reset reserved Type Reset RO 0 INTID Bit/Field Name Type Reset 31:5 reserved RO 0x0000.00 4:0 INTID WO 0x00 WO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Interrupt ID This field holds the interrupt ID of the required SGI. For example, a value of 0x3 generates an interrupt on IRQ3. 3.5 System Control Block (SCB) Register Descriptions This section lists and describes the System Control Block (SCB) registers, in numerical order by address offset. The SCB registers can only be accessed from privileged mode. All registers must be accessed with aligned word accesses except for the FAULTSTAT and SYSPRI1-SYSPRI3 registers, which can be accessed with byte or aligned halfword or word accesses. The processor does not support unaligned accesses to system control block registers. July 14, 2014 103 Texas Instruments-Production Data Cortex-M3 Peripherals Register 18: CPU ID Base (CPUID), offset 0xD00 Note: This register can only be accessed from privileged mode. The CPUID register contains the ARM® Cortex™-M3 processor part number, version, and implementation information. CPU ID Base (CPUID) Base 0xE000.E000 Offset 0xD00 Type RO, reset 0x410F.C231 31 30 29 28 27 26 25 24 23 22 IMP Type Reset 21 20 19 18 VAR RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 PARTNO Type Reset RO 1 RO 1 RO 0 RO 0 RO 0 RO 0 RO 1 17 16 RO 1 RO 1 1 0 RO 0 RO 1 CON REV RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:24 IMP RO 0x41 Implementer Code RO 1 RO 1 RO 0 RO 0 Value Description 0x41 ARM 23:20 VAR RO 0x0 Variant Number Value Description 0x0 19:16 CON RO 0xF The rn value in the rnpn product revision identifier, for example, the 0 in r0p1. Constant Value Description 0xF 15:4 PARTNO RO 0xC23 Always reads as 0xF. Part Number Value Description 0xC23 Cortex-M3 processor. 3:0 REV RO 0x1 Revision Number Value Description 0x1 The pn value in the rnpn product revision identifier, for example, the 1 in r0p1. 104 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 19: Interrupt Control and State (INTCTRL), offset 0xD04 Note: This register can only be accessed from privileged mode. The INCTRL register provides a set-pending bit for the NMI exception, and set-pending and clear-pending bits for the PendSV and SysTick exceptions. In addition, bits in this register indicate the exception number of the exception being processed, whether there are preempted active exceptions, the exception number of the highest priority pending exception, and whether any interrupts are pending. When writing to INCTRL, the effect is unpredictable when writing a 1 to both the PENDSV and UNPENDSV bits, or writing a 1 to both the PENDSTSET and PENDSTCLR bits. Interrupt Control and State (INTCTRL) Base 0xE000.E000 Offset 0xD04 Type R/W, reset 0x0000.0000 31 30 NMISET Type Reset 29 reserved 28 26 PENDSV UNPENDSV 25 PENDSTSET PENDSTCLR 24 reserved 23 22 21 20 ISRPRE ISRPEND 19 18 17 reserved 16 VECPEND R/W 0 RO 0 RO 0 R/W 0 WO 0 R/W 0 WO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 VECPEND Type Reset 27 RO 0 RETBASE RO 0 reserved RO 0 Bit/Field Name Type Reset 31 NMISET R/W 0 RO 0 VECACT Description NMI Set Pending Value Description 0 On a read, indicates an NMI exception is not pending. On a write, no effect. 1 On a read, indicates an NMI exception is pending. On a write, changes the NMI exception state to pending. Because NMI is the highest-priority exception, normally the processor enters the NMI exception handler as soon as it registers the setting of this bit, and clears this bit on entering the interrupt handler. A read of this bit by the NMI exception handler returns 1 only if the NMI signal is reasserted while the processor is executing that handler. 30:29 reserved RO 0x0 28 PENDSV R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PendSV Set Pending Value Description 0 On a read, indicates a PendSV exception is not pending. On a write, no effect. 1 On a read, indicates a PendSV exception is pending. On a write, changes the PendSV exception state to pending. Setting this bit is the only way to set the PendSV exception state to pending. This bit is cleared by writing a 1 to the UNPENDSV bit. July 14, 2014 105 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 27 UNPENDSV WO 0 Description PendSV Clear Pending Value Description 0 On a write, no effect. 1 On a write, removes the pending state from the PendSV exception. This bit is write only; on a register read, its value is unknown. 26 PENDSTSET R/W 0 SysTick Set Pending Value Description 0 On a read, indicates a SysTick exception is not pending. On a write, no effect. 1 On a read, indicates a SysTick exception is pending. On a write, changes the SysTick exception state to pending. This bit is cleared by writing a 1 to the PENDSTCLR bit. 25 PENDSTCLR WO 0 SysTick Clear Pending Value Description 0 On a write, no effect. 1 On a write, removes the pending state from the SysTick exception. This bit is write only; on a register read, its value is unknown. 24 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23 ISRPRE RO 0 Debug Interrupt Handling Value Description 0 The release from halt does not take an interrupt. 1 The release from halt takes an interrupt. This bit is only meaningful in Debug mode and reads as zero when the processor is not in Debug mode. 22 ISRPEND RO 0 Interrupt Pending Value Description 0 No interrupt is pending. 1 An interrupt is pending. This bit provides status for all interrupts excluding NMI and Faults. 21:18 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 106 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset Description 17:12 VECPEND RO 0x00 Interrupt Pending Vector Number This field contains the exception number of the highest priority pending enabled exception. The value indicated by this field includes the effect of the BASEPRI and FAULTMASK registers, but not any effect of the PRIMASK register. Value Description 0x00 No exceptions are pending 0x01 Reserved 0x02 NMI 0x03 Hard fault 0x04 Memory management fault 0x05 Bus fault 0x06 Usage fault 0x07-0x0A Reserved 0x0B SVCall 0x0C Reserved for Debug 0x0D Reserved 0x0E PendSV 0x0F SysTick 0x10 Interrupt Vector 0 0x11 Interrupt Vector 1 ... ... 0x2D Interrupt Vector 29 0x2E-0x3F Reserved 11 RETBASE RO 0 Return to Base Value Description 0 There are preempted active exceptions to execute. 1 There are no active exceptions, or the currently executing exception is the only active exception. This bit provides status for all interrupts excluding NMI and Faults. This bit only has meaning if the processor is currently executing an ISR (the Interrupt Program Status (IPSR) register is non-zero). 10:6 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:0 VECACT RO 0x00 Interrupt Pending Vector Number This field contains the active exception number. The exception numbers can be found in the description for the VECPEND field. If this field is clear, the processor is in Thread mode. This field contains the same value as the ISRNUM field in the IPSR register. Subtract 16 from this value to obtain the IRQ number required to index into the Interrupt Set Enable (ENn), Interrupt Clear Enable (DISn), Interrupt Set Pending (PENDn), Interrupt Clear Pending (UNPENDn), and Interrupt Priority (PRIn) registers (see page 51). July 14, 2014 107 Texas Instruments-Production Data Cortex-M3 Peripherals Register 20: Vector Table Offset (VTABLE), offset 0xD08 Note: This register can only be accessed from privileged mode. The VTABLE register indicates the offset of the vector table base address from memory address 0x0000.0000. Vector Table Offset (VTABLE) Base 0xE000.E000 Offset 0xD08 Type R/W, reset 0x0000.0000 31 30 reserved Type Reset 29 28 27 26 25 24 23 BASE 22 21 20 19 18 17 16 OFFSET RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 OFFSET Type Reset R/W 0 R/W 0 R/W 0 R/W 0 reserved R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:30 reserved RO 0x0 29 BASE R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Vector Table Base Value Description 28:8 OFFSET R/W 0x000.00 0 The vector table is in the code memory region. 1 The vector table is in the SRAM memory region. Vector Table Offset When configuring the OFFSET field, the offset must be aligned to the number of exception entries in the vector table. Because there are 29 interrupts, the offset must be aligned on a 256-byte boundary. 7:0 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 108 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 21: Application Interrupt and Reset Control (APINT), offset 0xD0C Note: This register can only be accessed from privileged mode. The APINT register provides priority grouping control for the exception model, endian status for data accesses, and reset control of the system. To write to this register, 0x05FA must be written to the VECTKEY field, otherwise the write is ignored. The PRIGROUP field indicates the position of the binary point that splits the INTx fields in the Interrupt Priority (PRIx) registers into separate group priority and subpriority fields. Table 3-8 on page 109 shows how the PRIGROUP value controls this split. The bit numbers in the Group Priority Field and Subpriority Field columns in the table refer to the bits in the INTA field. For the INTB field, the corresponding bits are 15:13; for INTC, 23:21; and for INTD, 31:29. Note: Determining preemption of an exception uses only the group priority field. Table 3-8. Interrupt Priority Levels a PRIGROUP Bit Field Binary Point Group Priority Field Subpriority Field Group Priorities Subpriorities 0x0 - 0x4 bxxx. [7:5] None 8 1 0x5 bxx.y [7:6] [5] 4 2 0x6 bx.yy [7] [6:5] 2 4 0x7 b.yyy None [7:5] 1 8 a. INTx field showing the binary point. An x denotes a group priority field bit, and a y denotes a subpriority field bit. Application Interrupt and Reset Control (APINT) Base 0xE000.E000 Offset 0xD0C Type R/W, reset 0xFA05.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 1 R/W 0 R/W 1 5 4 3 2 1 0 VECTKEY Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 0 15 14 13 12 11 10 reserved ENDIANESS Type Reset RO 0 RO 0 RO 0 RO 0 R/W 1 R/W 0 R/W 0 R/W 0 9 8 7 6 PRIGROUP RO 0 R/W 0 R/W 0 Bit/Field Name Type Reset 31:16 VECTKEY R/W 0xFA05 reserved R/W 0 RO 0 RO 0 RO 0 SYSRESREQ VECTCLRACT VECTRESET RO 0 RO 0 WO 0 WO 0 WO 0 Description Register Key This field is used to guard against accidental writes to this register. 0x05FA must be written to this field in order to change the bits in this register. On a read, 0xFA05 is returned. 15 ENDIANESS RO 0 Data Endianess The Stellaris implementation uses only little-endian mode so this is cleared to 0. 14:11 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 109 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 10:8 PRIGROUP R/W 0x0 Description Interrupt Priority Grouping This field determines the split of group priority from subpriority (see Table 3-8 on page 109 for more information). 7:3 reserved RO 0x0 2 SYSRESREQ WO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. System Reset Request Value Description 0 No effect. 1 Resets the core and all on-chip peripherals except the Debug interface. This bit is automatically cleared during the reset of the core and reads as 0. 1 VECTCLRACT WO 0 Clear Active NMI / Fault This bit is reserved for Debug use and reads as 0. This bit must be written as a 0, otherwise behavior is unpredictable. 0 VECTRESET WO 0 System Reset This bit is reserved for Debug use and reads as 0. This bit must be written as a 0, otherwise behavior is unpredictable. 110 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 22: System Control (SYSCTRL), offset 0xD10 Note: This register can only be accessed from privileged mode. The SYSCTRL register controls features of entry to and exit from low-power state. System Control (SYSCTRL) Base 0xE000.E000 Offset 0xD10 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:5 reserved RO 0x0000.00 4 SEVONPEND R/W 0 RO 0 RO 0 RO 0 RO 0 4 3 SEVONPEND reserved R/W 0 RO 0 SLEEPDEEP SLEEPEXIT R/W 0 R/W 0 0 reserved RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Wake Up on Pending Value Description 0 Only enabled interrupts or events can wake up the processor; disabled interrupts are excluded. 1 Enabled events and all interrupts, including disabled interrupts, can wake up the processor. When an event or interrupt enters the pending state, the event signal wakes up the processor from WFE. If the processor is not waiting for an event, the event is registered and affects the next WFE. The processor also wakes up on execution of a SEV instruction or an external event. 3 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 SLEEPDEEP R/W 0 Deep Sleep Enable Value Description 0 Use Sleep mode as the low power mode. 1 Use Deep-sleep mode as the low power mode. July 14, 2014 111 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 1 SLEEPEXIT R/W 0 Description Sleep on ISR Exit Value Description 0 When returning from Handler mode to Thread mode, do not sleep when returning to Thread mode. 1 When returning from Handler mode to Thread mode, enter sleep or deep sleep on return from an ISR. Setting this bit enables an interrupt-driven application to avoid returning to an empty main application. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 112 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 23: Configuration and Control (CFGCTRL), offset 0xD14 Note: This register can only be accessed from privileged mode. The CFGCTRL register controls entry to Thread mode and enables: the handlers for NMI, hard fault and faults escalated by the FAULTMASK register to ignore bus faults; trapping of divide by zero and unaligned accesses; and access to the SWTRIG register by unprivileged software (see page 103). Configuration and Control (CFGCTRL) Base 0xE000.E000 Offset 0xD14 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 6 5 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 reserved STKALIGN BFHFNMIGN RO 0 RO 0 R/W 0 Bit/Field Name Type Reset 31:10 reserved RO 0x0000.00 9 STKALIGN R/W 0 R/W 0 RO 0 RO 0 RO 0 4 3 DIV0 UNALIGNED R/W 0 R/W 0 reserved MAINPEND BASETHR RO 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Stack Alignment on Exception Entry Value Description 0 The stack is 4-byte aligned. 1 The stack is 8-byte aligned. On exception entry, the processor uses bit 9 of the stacked PSR to indicate the stack alignment. On return from the exception, it uses this stacked bit to restore the correct stack alignment. 8 BFHFNMIGN R/W 0 Ignore Bus Fault in NMI and Fault This bit enables handlers with priority -1 or -2 to ignore data bus faults caused by load and store instructions. The setting of this bit applies to the hard fault, NMI, and FAULTMASK escalated handlers. Value Description 0 Data bus faults caused by load and store instructions cause a lock-up. 1 Handlers running at priority -1 and -2 ignore data bus faults caused by load and store instructions. Set this bit only when the handler and its data are in absolutely safe memory. The normal use of this bit is to probe system devices and bridges to detect control path problems and fix them. 7:5 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 113 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 4 DIV0 R/W 0 Description Trap on Divide by 0 This bit enables faulting or halting when the processor executes an SDIV or UDIV instruction with a divisor of 0. Value Description 3 UNALIGNED R/W 0 0 Do not trap on divide by 0. A divide by zero returns a quotient of 0. 1 Trap on divide by 0. Trap on Unaligned Access Value Description 0 Do not trap on unaligned halfword and word accesses. 1 Trap on unaligned halfword and word accesses. An unaligned access generates a usage fault. Unaligned LDM, STM, LDRD, and STRD instructions always fault regardless of whether UNALIGNED is set. 2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 MAINPEND R/W 0 Allow Main Interrupt Trigger Value Description 0 BASETHR R/W 0 0 Disables unprivileged software access to the SWTRIG register. 1 Enables unprivileged software access to the SWTRIG register (see page 103). Thread State Control Value Description 0 The processor can enter Thread mode only when no exception is active. 1 The processor can enter Thread mode from any level under the control of an EXC_RETURN value (see “Exception Return” on page 74 for more information). 114 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 24: System Handler Priority 1 (SYSPRI1), offset 0xD18 Note: This register can only be accessed from privileged mode. The SYSPRI1 register configures the priority level, 0 to 7 of the usage fault, bus fault, and memory management fault exception handlers. This register is byte-accessible. System Handler Priority 1 (SYSPRI1) Base 0xE000.E000 Offset 0xD18 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 14 13 12 11 15 BUS Type Reset R/W 0 R/W 0 RO 0 RO 0 RO 0 R/W 0 10 9 8 7 reserved R/W 0 RO 0 22 21 20 19 USAGE RO 0 RO 0 R/W 0 R/W 0 RO 0 RO 0 6 5 4 3 MEM RO 0 RO 0 R/W 0 R/W 0 18 17 16 RO 0 RO 0 RO 0 2 1 0 RO 0 RO 0 reserved reserved R/W 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:21 USAGE R/W 0x0 Usage Fault Priority This field configures the priority level of the usage fault. Configurable priority values are in the range 0-7, with lower values having higher priority. 20:16 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:13 BUS R/W 0x0 Bus Fault Priority This field configures the priority level of the bus fault. Configurable priority values are in the range 0-7, with lower values having higher priority. 12:8 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:5 MEM R/W 0x0 Memory Management Fault Priority This field configures the priority level of the memory management fault. Configurable priority values are in the range 0-7, with lower values having higher priority. 4:0 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 115 Texas Instruments-Production Data Cortex-M3 Peripherals Register 25: System Handler Priority 2 (SYSPRI2), offset 0xD1C Note: This register can only be accessed from privileged mode. The SYSPRI2 register configures the priority level, 0 to 7 of the SVCall handler. This register is byte-accessible. System Handler Priority 2 (SYSPRI2) Base 0xE000.E000 Offset 0xD1C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 SVC Type Reset 22 21 20 19 18 17 16 reserved R/W 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:29 SVC R/W 0x0 RO 0 Description SVCall Priority This field configures the priority level of SVCall. Configurable priority values are in the range 0-7, with lower values having higher priority. 28:0 reserved RO 0x000.0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 116 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 26: System Handler Priority 3 (SYSPRI3), offset 0xD20 Note: This register can only be accessed from privileged mode. The SYSPRI3 register configures the priority level, 0 to 7 of the SysTick exception and PendSV handlers. This register is byte-accessible. System Handler Priority 3 (SYSPRI3) Base 0xE000.E000 Offset 0xD20 Type R/W, reset 0x0000.0000 31 30 29 28 27 TICK Type Reset 26 25 24 23 reserved R/W 0 R/W 0 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 15 14 13 12 11 10 9 8 7 reserved Type Reset RO 0 RO 0 RO 0 RO 0 22 21 20 19 PENDSV R/W 0 R/W 0 RO 0 RO 0 6 5 4 3 DEBUG RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:29 TICK R/W 0x0 RO 0 R/W 0 R/W 0 18 17 16 RO 0 RO 0 RO 0 2 1 0 RO 0 RO 0 reserved reserved R/W 0 RO 0 RO 0 RO 0 Description SysTick Exception Priority This field configures the priority level of the SysTick exception. Configurable priority values are in the range 0-7, with lower values having higher priority. 28:24 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:21 PENDSV R/W 0x0 PendSV Priority This field configures the priority level of PendSV. Configurable priority values are in the range 0-7, with lower values having higher priority. 20:8 reserved RO 0x000 7:5 DEBUG R/W 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Debug Priority This field configures the priority level of Debug. Configurable priority values are in the range 0-7, with lower values having higher priority. 4:0 reserved RO 0x0.0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 117 Texas Instruments-Production Data Cortex-M3 Peripherals Register 27: System Handler Control and State (SYSHNDCTRL), offset 0xD24 Note: This register can only be accessed from privileged mode. The SYSHNDCTRL register enables the system handlers, and indicates the pending status of the usage fault, bus fault, memory management fault, and SVC exceptions as well as the active status of the system handlers. If a system handler is disabled and the corresponding fault occurs, the processor treats the fault as a hard fault. This register can be modified to change the pending or active status of system exceptions. An OS kernel can write to the active bits to perform a context switch that changes the current exception type. Caution – Software that changes the value of an active bit in this register without correct adjustment to the stacked content can cause the processor to generate a fault exception. Ensure software that writes to this register retains and subsequently restores the current active status. If the value of a bit in this register must be modified after enabling the system handlers, a read-modify-write procedure must be used to ensure that only the required bit is modified. System Handler Control and State (SYSHNDCTRL) Base 0xE000.E000 Offset 0xD24 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 SVC BUSP MEMP USAGEP R/W 0 R/W 0 R/W 0 R/W 0 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 USAGE BUS MEM R/W 0 R/W 0 R/W 0 10 9 8 7 6 5 4 3 2 1 0 TICK PNDSV reserved MON SVCA R/W 0 R/W 0 RO 0 R/W 0 R/W 0 USGA reserved BUSA MEMA R/W 0 RO 0 R/W 0 R/W 0 reserved Type Reset Type Reset reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:19 reserved RO 0x000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 18 USAGE R/W 0 Usage Fault Enable Value Description 17 BUS R/W 0 0 Disables the usage fault exception. 1 Enables the usage fault exception. Bus Fault Enable Value Description 0 Disables the bus fault exception. 1 Enables the bus fault exception. 118 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 16 MEM R/W 0 Description Memory Management Fault Enable Value Description 15 SVC R/W 0 0 Disables the memory management fault exception. 1 Enables the memory management fault exception. SVC Call Pending Value Description 0 An SVC call exception is not pending. 1 An SVC call exception is pending. This bit can be modified to change the pending status of the SVC call exception. 14 BUSP R/W 0 Bus Fault Pending Value Description 0 A bus fault exception is not pending. 1 A bus fault exception is pending. This bit can be modified to change the pending status of the bus fault exception. 13 MEMP R/W 0 Memory Management Fault Pending Value Description 0 A memory management fault exception is not pending. 1 A memory management fault exception is pending. This bit can be modified to change the pending status of the memory management fault exception. 12 USAGEP R/W 0 Usage Fault Pending Value Description 0 A usage fault exception is not pending. 1 A usage fault exception is pending. This bit can be modified to change the pending status of the usage fault exception. 11 TICK R/W 0 SysTick Exception Active Value Description 0 A SysTick exception is not active. 1 A SysTick exception is active. This bit can be modified to change the active status of the SysTick exception, however, see the Caution above before setting this bit. July 14, 2014 119 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 10 PNDSV R/W 0 Description PendSV Exception Active Value Description 0 A PendSV exception is not active. 1 A PendSV exception is active. This bit can be modified to change the active status of the PendSV exception, however, see the Caution above before setting this bit. 9 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 8 MON R/W 0 Debug Monitor Active Value Description 7 SVCA R/W 0 0 The Debug monitor is not active. 1 The Debug monitor is active. SVC Call Active Value Description 0 SVC call is not active. 1 SVC call is active. This bit can be modified to change the active status of the SVC call exception, however, see the Caution above before setting this bit. 6:4 reserved RO 0x0 3 USGA R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Usage Fault Active Value Description 0 Usage fault is not active. 1 Usage fault is active. This bit can be modified to change the active status of the usage fault exception, however, see the Caution above before setting this bit. 2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 BUSA R/W 0 Bus Fault Active Value Description 0 Bus fault is not active. 1 Bus fault is active. This bit can be modified to change the active status of the bus fault exception, however, see the Caution above before setting this bit. 120 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 0 MEMA R/W 0 Description Memory Management Fault Active Value Description 0 Memory management fault is not active. 1 Memory management fault is active. This bit can be modified to change the active status of the memory management fault exception, however, see the Caution above before setting this bit. July 14, 2014 121 Texas Instruments-Production Data Cortex-M3 Peripherals Register 28: Configurable Fault Status (FAULTSTAT), offset 0xD28 Note: This register can only be accessed from privileged mode. The FAULTSTAT register indicates the cause of a memory management fault, bus fault, or usage fault. Each of these functions is assigned to a subregister as follows: ■ Usage Fault Status (UFAULTSTAT), bits 31:16 ■ Bus Fault Status (BFAULTSTAT), bits 15:8 ■ Memory Management Fault Status (MFAULTSTAT), bits 7:0 FAULTSTAT is byte accessible. FAULTSTAT or its subregisters can be accessed as follows: ■ ■ ■ ■ ■ The complete FAULTSTAT register, with a word access to offset 0xD28 The MFAULTSTAT, with a byte access to offset 0xD28 The MFAULTSTAT and BFAULTSTAT, with a halfword access to offset 0xD28 The BFAULTSTAT, with a byte access to offset 0xD29 The UFAULTSTAT, with a halfword access to offset 0xD2A Bits are cleared by writing a 1 to them. In a fault handler, the true faulting address can be determined by: 1. Read and save the Memory Management Fault Address (MMADDR) or Bus Fault Address (FAULTADDR) value. 2. Read the MMARV bit in MFAULTSTAT, or the BFARV bit in BFAULTSTAT to determine if the MMADDR or FAULTADDR contents are valid. Software must follow this sequence because another higher priority exception might change the MMADDR or FAULTADDR value. For example, if a higher priority handler preempts the current fault handler, the other fault might change the MMADDR or FAULTADDR value. Configurable Fault Status (FAULTSTAT) Base 0xE000.E000 Offset 0xD28 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 reserved Type Reset RO 0 RO 0 RO 0 15 14 13 BFARV Type Reset R/W1C 0 reserved RO 0 RO 0 RO 0 RO 0 RO 0 25 24 DIV0 UNALIGN R/W1C 0 R/W1C 0 23 22 21 20 reserved RO 0 RO 0 RO 0 6 5 12 11 10 9 8 7 BSTKE BUSTKE IMPRE PRECISE IBUS MMARV R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved RO 0 RO 0 RO 0 4 MSTKE R/W1C 0 19 18 17 16 NOCP INVPC INVSTAT UNDEF R/W1C 0 R/W1C 0 R/W1C 0 R/W1C 0 3 2 MUSTKE reserved R/W1C 0 RO 0 1 0 DERR IERR R/W1C 0 R/W1C 0 Bit/Field Name Type Reset Description 31:26 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 122 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 25 DIV0 R/W1C 0 Description Divide-by-Zero Usage Fault Value Description 0 No divide-by-zero fault has occurred, or divide-by-zero trapping is not enabled. 1 The processor has executed an SDIV or UDIV instruction with a divisor of 0. When this bit is set, the PC value stacked for the exception return points to the instruction that performed the divide by zero. Trapping on divide-by-zero is enabled by setting the DIV0 bit in the Configuration and Control (CFGCTRL) register (see page 113). This bit is cleared by writing a 1 to it. 24 UNALIGN R/W1C 0 Unaligned Access Usage Fault Value Description 0 No unaligned access fault has occurred, or unaligned access trapping is not enabled. 1 The processor has made an unaligned memory access. Unaligned LDM, STM, LDRD, and STRD instructions always fault regardless of the configuration of this bit. Trapping on unaligned access is enabled by setting the UNALIGNED bit in the CFGCTRL register (see page 113). This bit is cleared by writing a 1 to it. 23:20 reserved RO 0x00 19 NOCP R/W1C 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. No Coprocessor Usage Fault Value Description 0 A usage fault has not been caused by attempting to access a coprocessor. 1 The processor has attempted to access a coprocessor. This bit is cleared by writing a 1 to it. 18 INVPC R/W1C 0 Invalid PC Load Usage Fault Value Description 0 A usage fault has not been caused by attempting to load an invalid PC value. 1 The processor has attempted an illegal load of EXC_RETURN to the PC as a result of an invalid context or an invalid EXC_RETURN value. When this bit is set, the PC value stacked for the exception return points to the instruction that tried to perform the illegal load of the PC. This bit is cleared by writing a 1 to it. July 14, 2014 123 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 17 INVSTAT R/W1C 0 Description Invalid State Usage Fault Value Description 0 A usage fault has not been caused by an invalid state. 1 The processor has attempted to execute an instruction that makes illegal use of the EPSR register. When this bit is set, the PC value stacked for the exception return points to the instruction that attempted the illegal use of the Execution Program Status Register (EPSR) register. This bit is not set if an undefined instruction uses the EPSR register. This bit is cleared by writing a 1 to it. 16 UNDEF R/W1C 0 Undefined Instruction Usage Fault Value Description 0 A usage fault has not been caused by an undefined instruction. 1 The processor has attempted to execute an undefined instruction. When this bit is set, the PC value stacked for the exception return points to the undefined instruction. An undefined instruction is an instruction that the processor cannot decode. This bit is cleared by writing a 1 to it. 15 BFARV R/W1C 0 Bus Fault Address Register Valid Value Description 0 The value in the Bus Fault Address (FAULTADDR) register is not a valid fault address. 1 The FAULTADDR register is holding a valid fault address. This bit is set after a bus fault, where the address is known. Other faults can clear this bit, such as a memory management fault occurring later. If a bus fault occurs and is escalated to a hard fault because of priority, the hard fault handler must clear this bit. This action prevents problems if returning to a stacked active bus fault handler whose FAULTADDR register value has been overwritten. This bit is cleared by writing a 1 to it. 14:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 124 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 12 BSTKE R/W1C 0 Description Stack Bus Fault Value Description 0 No bus fault has occurred on stacking for exception entry. 1 Stacking for an exception entry has caused one or more bus faults. When this bit is set, the SP is still adjusted but the values in the context area on the stack might be incorrect. A fault address is not written to the FAULTADDR register. This bit is cleared by writing a 1 to it. 11 BUSTKE R/W1C 0 Unstack Bus Fault Value Description 0 No bus fault has occurred on unstacking for a return from exception. 1 Unstacking for a return from exception has caused one or more bus faults. This fault is chained to the handler. Thus, when this bit is set, the original return stack is still present. The SP is not adjusted from the failing return, a new save is not performed, and a fault address is not written to the FAULTADDR register. This bit is cleared by writing a 1 to it. 10 IMPRE R/W1C 0 Imprecise Data Bus Error Value Description 0 An imprecise data bus error has not occurred. 1 A data bus error has occurred, but the return address in the stack frame is not related to the instruction that caused the error. When this bit is set, a fault address is not written to the FAULTADDR register. This fault is asynchronous. Therefore, if the fault is detected when the priority of the current process is higher than the bus fault priority, the bus fault becomes pending and becomes active only when the processor returns from all higher-priority processes. If a precise fault occurs before the processor enters the handler for the imprecise bus fault, the handler detects that both the IMPRE bit is set and one of the precise fault status bits is set. This bit is cleared by writing a 1 to it. 9 PRECISE R/W1C 0 Precise Data Bus Error Value Description 0 A precise data bus error has not occurred. 1 A data bus error has occurred, and the PC value stacked for the exception return points to the instruction that caused the fault. When this bit is set, the fault address is written to the FAULTADDR register. This bit is cleared by writing a 1 to it. July 14, 2014 125 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 8 IBUS R/W1C 0 Description Instruction Bus Error Value Description 0 An instruction bus error has not occurred. 1 An instruction bus error has occurred. The processor detects the instruction bus error on prefetching an instruction, but sets this bit only if it attempts to issue the faulting instruction. When this bit is set, a fault address is not written to the FAULTADDR register. This bit is cleared by writing a 1 to it. 7 MMARV R/W1C 0 Memory Management Fault Address Register Valid Value Description 0 The value in the Memory Management Fault Address (MMADDR) register is not a valid fault address. 1 The MMADDR register is holding a valid fault address. If a memory management fault occurs and is escalated to a hard fault because of priority, the hard fault handler must clear this bit. This action prevents problems if returning to a stacked active memory management fault handler whose MMADDR register value has been overwritten. This bit is cleared by writing a 1 to it. 6:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 MSTKE R/W1C 0 Stack Access Violation Value Description 0 No memory management fault has occurred on stacking for exception entry. 1 Stacking for an exception entry has caused one or more access violations. When this bit is set, the SP is still adjusted but the values in the context area on the stack might be incorrect. A fault address is not written to the MMADDR register. This bit is cleared by writing a 1 to it. 126 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 3 MUSTKE R/W1C 0 Description Unstack Access Violation Value Description 0 No memory management fault has occurred on unstacking for a return from exception. 1 Unstacking for a return from exception has caused one or more access violations. This fault is chained to the handler. Thus, when this bit is set, the original return stack is still present. The SP is not adjusted from the failing return, a new save is not performed, and a fault address is not written to the MMADDR register. This bit is cleared by writing a 1 to it. 2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 DERR R/W1C 0 Data Access Violation Value Description 0 A data access violation has not occurred. 1 The processor attempted a load or store at a location that does not permit the operation. When this bit is set, the PC value stacked for the exception return points to the faulting instruction and the address of the attempted access is written to the MMADDR register. This bit is cleared by writing a 1 to it. 0 IERR R/W1C 0 Instruction Access Violation Value Description 0 An instruction access violation has not occurred. 1 The processor attempted an instruction fetch from a location that does not permit execution. This fault occurs on any access to an XN region, even when the MPU is disabled or not present. When this bit is set, the PC value stacked for the exception return points to the faulting instruction and the address of the attempted access is not written to the MMADDR register. This bit is cleared by writing a 1 to it. July 14, 2014 127 Texas Instruments-Production Data Cortex-M3 Peripherals Register 29: Hard Fault Status (HFAULTSTAT), offset 0xD2C Note: This register can only be accessed from privileged mode. The HFAULTSTAT register gives information about events that activate the hard fault handler. Bits are cleared by writing a 1 to them. Hard Fault Status (HFAULTSTAT) Base 0xE000.E000 Offset 0xD2C Type R/W1C, reset 0x0000.0000 Type Reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 DBG FORCED R/W1C 0 R/W1C 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 VECT reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 RO 0 reserved Type Reset Bit/Field Name Type Reset 31 DBG R/W1C 0 Description Debug Event This bit is reserved for Debug use. This bit must be written as a 0, otherwise behavior is unpredictable. 30 FORCED R/W1C 0 Forced Hard Fault Value Description 0 No forced hard fault has occurred. 1 A forced hard fault has been generated by escalation of a fault with configurable priority that cannot be handled, either because of priority or because it is disabled. When this bit is set, the hard fault handler must read the other fault status registers to find the cause of the fault. This bit is cleared by writing a 1 to it. 29:2 reserved RO 0x00 1 VECT R/W1C 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Vector Table Read Fault Value Description 0 No bus fault has occurred on a vector table read. 1 A bus fault occurred on a vector table read. This error is always handled by the hard fault handler. When this bit is set, the PC value stacked for the exception return points to the instruction that was preempted by the exception. This bit is cleared by writing a 1 to it. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 128 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 30: Memory Management Fault Address (MMADDR), offset 0xD34 Note: This register can only be accessed from privileged mode. The MMADDR register contains the address of the location that generated a memory management fault. When an unaligned access faults, the address in the MMADDR register is the actual address that faulted. Because a single read or write instruction can be split into multiple aligned accesses, the fault address can be any address in the range of the requested access size. Bits in the Memory Management Fault Status (MFAULTSTAT) register indicate the cause of the fault and whether the value in the MMADDR register is valid (see page 122). Memory Management Fault Address (MMADDR) Base 0xE000.E000 Offset 0xD34 Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - ADDR Type Reset R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 ADDR Type Reset R/W - R/W - R/W - R/W - R/W - R/W - R/W - Bit/Field Name Type Reset 31:0 ADDR R/W - R/W - Description Fault Address When the MMARV bit of MFAULTSTAT is set, this field holds the address of the location that generated the memory management fault. July 14, 2014 129 Texas Instruments-Production Data Cortex-M3 Peripherals Register 31: Bus Fault Address (FAULTADDR), offset 0xD38 Note: This register can only be accessed from privileged mode. The FAULTADDR register contains the address of the location that generated a bus fault. When an unaligned access faults, the address in the FAULTADDR register is the one requested by the instruction, even if it is not the address of the fault. Bits in the Bus Fault Status (BFAULTSTAT) register indicate the cause of the fault and whether the value in the FAULTADDR register is valid (see page 122). Bus Fault Address (FAULTADDR) Base 0xE000.E000 Offset 0xD38 Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 7 6 5 4 3 2 1 0 R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - ADDR Type Reset R/W - R/W - R/W - R/W - R/W - R/W - R/W - R/W - 15 14 13 12 11 10 9 8 ADDR Type Reset R/W - R/W - R/W - R/W - R/W - R/W - R/W - Bit/Field Name Type Reset 31:0 ADDR R/W - R/W - Description Fault Address When the FAULTADDRV bit of BFAULTSTAT is set, this field holds the address of the location that generated the bus fault. 3.6 Memory Protection Unit (MPU) Register Descriptions This section lists and describes the Memory Protection Unit (MPU) registers, in numerical order by address offset. The MPU registers can only be accessed from privileged mode. 130 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 32: MPU Type (MPUTYPE), offset 0xD90 Note: This register can only be accessed from privileged mode. The MPUTYPE register indicates whether the MPU is present, and if so, how many regions it supports. MPU Type (MPUTYPE) Base 0xE000.E000 Offset 0xD90 Type RO, reset 0x0000.0800 31 30 29 28 27 26 25 24 23 22 21 20 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 DREGION Type Reset RO 0 RO 0 RO 0 RO 0 19 18 17 16 RO 0 IREGION RO 0 RO 0 RO 0 RO 0 4 3 2 1 reserved RO 1 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 0 SEPARATE RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:24 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 23:16 IREGION RO 0x00 Number of I Regions This field indicates the number of supported MPU instruction regions. This field always contains 0x00. The MPU memory map is unified and is described by the DREGION field. 15:8 DREGION RO 0x08 Number of D Regions Value Description 0x08 Indicates there are eight supported MPU data regions. 7:1 reserved RO 0x00 0 SEPARATE RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Separate or Unified MPU Value Description 0 Indicates the MPU is unified. July 14, 2014 131 Texas Instruments-Production Data Cortex-M3 Peripherals Register 33: MPU Control (MPUCTRL), offset 0xD94 Note: This register can only be accessed from privileged mode. The MPUCTRL register enables the MPU, enables the default memory map background region, and enables use of the MPU when in the hard fault, Non-maskable Interrupt (NMI), and Fault Mask Register (FAULTMASK) escalated handlers. When the ENABLE and PRIVDEFEN bits are both set: ■ For privileged accesses, the default memory map is as described in “Memory Model” on page 59. Any access by privileged software that does not address an enabled memory region behaves as defined by the default memory map. ■ Any access by unprivileged software that does not address an enabled memory region causes a memory management fault. Execute Never (XN) and Strongly Ordered rules always apply to the System Control Space regardless of the value of the ENABLE bit. When the ENABLE bit is set, at least one region of the memory map must be enabled for the system to function unless the PRIVDEFEN bit is set. If the PRIVDEFEN bit is set and no regions are enabled, then only privileged software can operate. When the ENABLE bit is clear, the system uses the default memory map, which has the same memory attributes as if the MPU is not implemented (see Table 2-5 on page 61 for more information). The default memory map applies to accesses from both privileged and unprivileged software. When the MPU is enabled, accesses to the System Control Space and vector table are always permitted. Other areas are accessible based on regions and whether PRIVDEFEN is set. Unless HFNMIENA is set, the MPU is not enabled when the processor is executing the handler for an exception with priority –1 or –2. These priorities are only possible when handling a hard fault or NMI exception or when FAULTMASK is enabled. Setting the HFNMIENA bit enables the MPU when operating with these two priorities. MPU Control (MPUCTRL) Base 0xE000.E000 Offset 0xD94 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 PRIVDEFEN HFNMIENA R/W 0 R/W 0 ENABLE R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 132 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 2 PRIVDEFEN R/W 0 Description MPU Default Region This bit enables privileged software access to the default memory map. Value Description 0 If the MPU is enabled, this bit disables use of the default memory map. Any memory access to a location not covered by any enabled region causes a fault. 1 If the MPU is enabled, this bit enables use of the default memory map as a background region for privileged software accesses. When this bit is set, the background region acts as if it is region number -1. Any region that is defined and enabled has priority over this default map. If the MPU is disabled, the processor ignores this bit. 1 HFNMIENA R/W 0 MPU Enabled During Faults This bit controls the operation of the MPU during hard fault, NMI, and FAULTMASK handlers. Value Description 0 The MPU is disabled during hard fault, NMI, and FAULTMASK handlers, regardless of the value of the ENABLE bit. 1 The MPU is enabled during hard fault, NMI, and FAULTMASK handlers. When the MPU is disabled and this bit is set, the resulting behavior is unpredictable. 0 ENABLE R/W 0 MPU Enable Value Description 0 The MPU is disabled. 1 The MPU is enabled. When the MPU is disabled and the HFNMIENA bit is set, the resulting behavior is unpredictable. July 14, 2014 133 Texas Instruments-Production Data Cortex-M3 Peripherals Register 34: MPU Region Number (MPUNUMBER), offset 0xD98 Note: This register can only be accessed from privileged mode. The MPUNUMBER register selects which memory region is referenced by the MPU Region Base Address (MPUBASE) and MPU Region Attribute and Size (MPUATTR) registers. Normally, the required region number should be written to this register before accessing the MPUBASE or the MPUATTR register. However, the region number can be changed by writing to the MPUBASE register with the VALID bit set (see page 135). This write updates the value of the REGION field. MPU Region Number (MPUNUMBER) Base 0xE000.E000 Offset 0xD98 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:3 reserved RO 0x0000.000 2:0 NUMBER R/W 0x0 NUMBER RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. MPU Region to Access This field indicates the MPU region referenced by the MPUBASE and MPUATTR registers. The MPU supports eight memory regions. 134 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 35: MPU Region Base Address (MPUBASE), offset 0xD9C Register 36: MPU Region Base Address Alias 1 (MPUBASE1), offset 0xDA4 Register 37: MPU Region Base Address Alias 2 (MPUBASE2), offset 0xDAC Register 38: MPU Region Base Address Alias 3 (MPUBASE3), offset 0xDB4 Note: This register can only be accessed from privileged mode. The MPUBASE register defines the base address of the MPU region selected by the MPU Region Number (MPUNUMBER) register and can update the value of the MPUNUMBER register. To change the current region number and update the MPUNUMBER register, write the MPUBASE register with the VALID bit set. The ADDR field is bits 31:N of the MPUBASE register. Bits (N-1):5 are reserved. The region size, as specified by the SIZE field in the MPU Region Attribute and Size (MPUATTR) register, defines the value of N where: N = Log2(Region size in bytes) If the region size is configured to 4 GB in the MPUATTR register, there is no valid ADDR field. In this case, the region occupies the complete memory map, and the base address is 0x0000.0000. The base address is aligned to the size of the region. For example, a 64-KB region must be aligned on a multiple of 64 KB, for example, at 0x0001.0000 or 0x0002.0000. MPU Region Base Address (MPUBASE) Base 0xE000.E000 Offset 0xD9C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 VALID reserved R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 WO 0 RO 0 ADDR Type Reset ADDR Type Reset R/W 0 Bit/Field Name Type Reset 31:5 ADDR R/W 0x0000.000 REGION R/W 0 R/W 0 R/W 0 Description Base Address Mask Bits 31:N in this field contain the region base address. The value of N depends on the region size, as shown above. The remaining bits (N-1):5 are reserved. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 135 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset 4 VALID WO 0 Description Region Number Valid Value Description 0 The MPUNUMBER register is not changed and the processor updates the base address for the region specified in the MPUNUMBER register and ignores the value of the REGION field. 1 The MPUNUMBER register is updated with the value of the REGION field and the base address is updated for the region specified in the REGION field. This bit is always read as 0. 3 reserved RO 0 2:0 REGION R/W 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Region Number On a write, contains the value to be written to the MPUNUMBER register. On a read, returns the current region number in the MPUNUMBER register. 136 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 39: MPU Region Attribute and Size (MPUATTR), offset 0xDA0 Register 40: MPU Region Attribute and Size Alias 1 (MPUATTR1), offset 0xDA8 Register 41: MPU Region Attribute and Size Alias 2 (MPUATTR2), offset 0xDB0 Register 42: MPU Region Attribute and Size Alias 3 (MPUATTR3), offset 0xDB8 Note: This register can only be accessed from privileged mode. The MPUATTR register defines the region size and memory attributes of the MPU region specified by the MPU Region Number (MPUNUMBER) register and enables that region and any subregions. The MPUATTR register is accessible using word or halfword accesses with the most-significant halfword holding the region attributes and the least-significant halfword holds the region size and the region and subregion enable bits. The MPU access permission attribute bits, XN, AP, TEX, S, C, and B, control access to the corresponding memory region. If an access is made to an area of memory without the required permissions, then the MPU generates a permission fault. The SIZE field defines the size of the MPU memory region specified by the MPUNUMBER register as follows: (Region size in bytes) = 2(SIZE+1) The smallest permitted region size is 32 bytes, corresponding to a SIZE value of 4. Table 3-9 on page 137 gives example SIZE values with the corresponding region size and value of N in the MPU Region Base Address (MPUBASE) register. Table 3-9. Example SIZE Field Values a SIZE Encoding Region Size Value of N Note 00100b (0x4) 32 B 5 Minimum permitted size 01001b (0x9) 1 KB 10 - 10011b (0x13) 1 MB 20 - 11101b (0x1D) 1 GB 30 - 11111b (0x1F) 4 GB No valid ADDR field in MPUBASE; the Maximum possible size region occupies the complete memory map. a. Refers to the N parameter in the MPUBASE register (see page 135). MPU Region Attribute and Size (MPUATTR) Base 0xE000.E000 Offset 0xDA0 Type R/W, reset 0x0000.0000 31 30 29 28 27 reserved Type Reset 26 25 24 23 AP 21 reserved 20 19 18 TEX 17 16 XN reserved S C B RO 0 RO 0 RO 0 R/W 0 RO 0 R/W 0 R/W 0 R/W 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 SRD Type Reset 22 reserved SIZE July 14, 2014 R/W 0 ENABLE R/W 0 137 Texas Instruments-Production Data Cortex-M3 Peripherals Bit/Field Name Type Reset Description 31:29 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 28 XN R/W 0 Instruction Access Disable Value Description 0 Instruction fetches are enabled. 1 Instruction fetches are disabled. 27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26:24 AP R/W 0 Access Privilege For information on using this bit field, see Table 3-5 on page 89. 23:22 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 21:19 TEX R/W 0x0 Type Extension Mask For information on using this bit field, see Table 3-3 on page 88. 18 S R/W 0 Shareable For information on using this bit, see Table 3-3 on page 88. 17 C R/W 0 Cacheable For information on using this bit, see Table 3-3 on page 88. 16 B R/W 0 Bufferable For information on using this bit, see Table 3-3 on page 88. 15:8 SRD R/W 0x00 Subregion Disable Bits Value Description 0 The corresponding subregion is enabled. 1 The corresponding subregion is disabled. Region sizes of 128 bytes and less do not support subregions. When writing the attributes for such a region, configure the SRD field as 0x00. See the section called “Subregions” on page 87 for more information. 7:6 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:1 SIZE R/W 0x0 Region Size Mask The SIZE field defines the size of the MPU memory region specified by the MPUNUMBER register. Refer to Table 3-9 on page 137 for more information. 138 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 0 ENABLE R/W 0 Description Region Enable Value Description 0 The region is disabled. 1 The region is enabled. July 14, 2014 139 Texas Instruments-Production Data JTAG Interface 4 JTAG Interface The Joint Test Action Group (JTAG) port is an IEEE standard that defines a Test Access Port and Boundary Scan Architecture for digital integrated circuits and provides a standardized serial interface for controlling the associated test logic. The TAP, Instruction Register (IR), and Data Registers (DR) can be used to test the interconnections of assembled printed circuit boards and obtain manufacturing information on the components. The JTAG Port also provides a means of accessing and controlling design-for-test features such as I/O pin observation and control, scan testing, and debugging. The JTAG port is comprised of five pins: TRST, TCK, TMS, TDI, and TDO. Data is transmitted serially into the controller on TDI and out of the controller on TDO. The interpretation of this data is dependent on the current state of the TAP controller. For detailed information on the operation of the JTAG port and TAP controller, please refer to the IEEE Standard 1149.1-Test Access Port and Boundary-Scan Architecture. ® The Stellaris JTAG controller works with the ARM JTAG controller built into the Cortex-M3 core. This is implemented by multiplexing the TDO outputs from both JTAG controllers. ARM JTAG instructions select the ARM TDO output while Stellaris JTAG instructions select the Stellaris TDO outputs. The multiplexer is controlled by the Stellaris JTAG controller, which has comprehensive programming for the ARM, Stellaris, and unimplemented JTAG instructions. The Stellaris JTAG module has the following features: ■ IEEE 1149.1-1990 compatible Test Access Port (TAP) controller ■ Four-bit Instruction Register (IR) chain for storing JTAG instructions ■ IEEE standard instructions: BYPASS, IDCODE, SAMPLE/PRELOAD, EXTEST and INTEST ■ ARM additional instructions: APACC, DPACC and ABORT ■ Integrated ARM Serial Wire Debug (SWD) See the ARM® Debug Interface V5 Architecture Specification for more information on the ARM JTAG controller. 140 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 4.1 Block Diagram Figure 4-1. JTAG Module Block Diagram TRST TCK TMS TAP Controller TDI Instruction Register (IR) BYPASS Data Register TDO Boundary Scan Data Register IDCODE Data Register ABORT Data Register DPACC Data Register APACC Data Register Cortex-M3 Debug Port 4.2 Signal Description Table 4-1 on page 141 lists the external signals of the JTAG/SWD controller and describes the function of each. The JTAG/SWD controller signals are alternate functions for some GPIO signals, however note that the reset state of the pins is for the JTAG/SWD function. The column in the table below titled "Pin Assignment" lists the GPIO pin placement for the JTAG/SWD controller signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) is set to choose the JTAG/SWD function. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 4-1. JTAG_SWD_SWO Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type SWCLK 40 I TTL Description JTAG/SWD CLK. SWDIO 39 I/O TTL JTAG TMS and SWDIO. SWO 37 O TTL JTAG TDO and SWO. TCK 40 I TTL JTAG/SWD CLK. TDI 38 I TTL JTAG TDI. TDO 37 O TTL JTAG TDO and SWO. TMS 39 I/O TTL JTAG TMS and SWDIO. TRST 41 I TTL JTAG TRST. a. The TTL designation indicates the pin has TTL-compatible voltage levels. July 14, 2014 141 Texas Instruments-Production Data JTAG Interface 4.3 Functional Description A high-level conceptual drawing of the JTAG module is shown in Figure 4-1 on page 141. The JTAG module is composed of the Test Access Port (TAP) controller and serial shift chains with parallel update registers. The TAP controller is a simple state machine controlled by the TRST, TCK and TMS inputs. The current state of the TAP controller depends on the current value of TRST and the sequence of values captured on TMS at the rising edge of TCK. The TAP controller determines when the serial shift chains capture new data, shift data from TDI towards TDO, and update the parallel load registers. The current state of the TAP controller also determines whether the Instruction Register (IR) chain or one of the Data Register (DR) chains is being accessed. The serial shift chains with parallel load registers are comprised of a single Instruction Register (IR) chain and multiple Data Register (DR) chains. The current instruction loaded in the parallel load register determines which DR chain is captured, shifted, or updated during the sequencing of the TAP controller. Some instructions, like EXTEST and INTEST, operate on data currently in a DR chain and do not capture, shift, or update any of the chains. Instructions that are not implemented decode to the BYPASS instruction to ensure that the serial path between TDI and TDO is always connected (see Table 4-3 on page 146 for a list of implemented instructions). See “JTAG and Boundary Scan” on page 464 for JTAG timing diagrams. 4.3.1 JTAG Interface Pins The JTAG interface consists of five standard pins: TRST,TCK, TMS, TDI, and TDO. These pins and their associated reset state are given in Table 4-2 on page 142. Detailed information on each pin follows. Table 4-2. JTAG Port Pins Reset State 4.3.1.1 Pin Name Data Direction Internal Pull-Up Internal Pull-Down Drive Strength Drive Value TRST Input Enabled Disabled N/A N/A TCK Input Enabled Disabled N/A N/A TMS Input Enabled Disabled N/A N/A TDI Input Enabled Disabled N/A N/A TDO Output Enabled Disabled 2-mA driver High-Z Test Reset Input (TRST) The TRST pin is an asynchronous active Low input signal for initializing and resetting the JTAG TAP controller and associated JTAG circuitry. When TRST is asserted, the TAP controller resets to the Test-Logic-Reset state and remains there while TRST is asserted. When the TAP controller enters the Test-Logic-Reset state, the JTAG Instruction Register (IR) resets to the default instruction, IDCODE. By default, the internal pull-up resistor on the TRST pin is enabled after reset. Changes to the pull-up resistor settings on GPIO Port B should ensure that the internal pull-up resistor remains enabled on PB7/TRST; otherwise JTAG communication could be lost. 4.3.1.2 Test Clock Input (TCK) The TCK pin is the clock for the JTAG module. This clock is provided so the test logic can operate independently of any other system clocks. In addition, it ensures that multiple JTAG TAP controllers that are daisy-chained together can synchronously communicate serial test data between 142 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller components. During normal operation, TCK is driven by a free-running clock with a nominal 50% duty cycle. When necessary, TCK can be stopped at 0 or 1 for extended periods of time. While TCK is stopped at 0 or 1, the state of the TAP controller does not change and data in the JTAG Instruction and Data Registers is not lost. By default, the internal pull-up resistor on the TCK pin is enabled after reset. This assures that no clocking occurs if the pin is not driven from an external source. The internal pull-up and pull-down resistors can be turned off to save internal power as long as the TCK pin is constantly being driven by an external source. 4.3.1.3 Test Mode Select (TMS) The TMS pin selects the next state of the JTAG TAP controller. TMS is sampled on the rising edge of TCK. Depending on the current TAP state and the sampled value of TMS, the next state is entered. Because the TMS pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1 expects the value on TMS to change on the falling edge of TCK. Holding TMS high for five consecutive TCK cycles drives the TAP controller state machine to the Test-Logic-Reset state. When the TAP controller enters the Test-Logic-Reset state, the JTAG Instruction Register (IR) resets to the default instruction, IDCODE. Therefore, this sequence can be used as a reset mechanism, similar to asserting TRST. The JTAG Test Access Port state machine can be seen in its entirety in Figure 4-2 on page 144. By default, the internal pull-up resistor on the TMS pin is enabled after reset. Changes to the pull-up resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled on PC1/TMS; otherwise JTAG communication could be lost. 4.3.1.4 Test Data Input (TDI) The TDI pin provides a stream of serial information to the IR chain and the DR chains. TDI is sampled on the rising edge of TCK and, depending on the current TAP state and the current instruction, presents this data to the proper shift register chain. Because the TDI pin is sampled on the rising edge of TCK, the IEEE Standard 1149.1 expects the value on TDI to change on the falling edge of TCK. By default, the internal pull-up resistor on the TDI pin is enabled after reset. Changes to the pull-up resistor settings on GPIO Port C should ensure that the internal pull-up resistor remains enabled on PC2/TDI; otherwise JTAG communication could be lost. 4.3.1.5 Test Data Output (TDO) The TDO pin provides an output stream of serial information from the IR chain or the DR chains. The value of TDO depends on the current TAP state, the current instruction, and the data in the chain being accessed. In order to save power when the JTAG port is not being used, the TDO pin is placed in an inactive drive state when not actively shifting out data. Because TDO can be connected to the TDI of another controller in a daisy-chain configuration, the IEEE Standard 1149.1 expects the value on TDO to change on the falling edge of TCK. By default, the internal pull-up resistor on the TDO pin is enabled after reset. This assures that the pin remains at a constant logic level when the JTAG port is not being used. The internal pull-up and pull-down resistors can be turned off to save internal power if a High-Z output value is acceptable during certain TAP controller states. 4.3.2 JTAG TAP Controller The JTAG TAP controller state machine is shown in Figure 4-2 on page 144. The TAP controller state machine is reset to the Test-Logic-Reset state on the assertion of a Power-On-Reset (POR) July 14, 2014 143 Texas Instruments-Production Data JTAG Interface or the assertion of TRST. Asserting the correct sequence on the TMS pin allows the JTAG module to shift in new instructions, shift in data, or idle during extended testing sequences. For detailed information on the function of the TAP controller and the operations that occur in each state, please refer to IEEE Standard 1149.1. Figure 4-2. Test Access Port State Machine Test Logic Reset 1 0 Run Test Idle 0 Select DR Scan 1 Select IR Scan 1 0 1 Capture DR 1 Capture IR 0 0 Shift DR Shift IR 0 1 Exit 1 DR Exit 1 IR 1 Pause IR 0 1 Exit 2 DR 0 1 0 Exit 2 IR 1 1 Update DR 4.3.3 1 0 Pause DR 1 0 1 0 0 1 0 0 Update IR 1 0 Shift Registers The Shift Registers consist of a serial shift register chain and a parallel load register. The serial shift register chain samples specific information during the TAP controller’s CAPTURE states and allows this information to be shifted out of TDO during the TAP controller’s SHIFT states. While the sampled data is being shifted out of the chain on TDO, new data is being shifted into the serial shift register on TDI. This new data is stored in the parallel load register during the TAP controller’s UPDATE states. Each of the shift registers is discussed in detail in “Register Descriptions” on page 146. 4.3.4 Operational Considerations There are certain operational considerations when using the JTAG module. Because the JTAG pins can be programmed to be GPIOs, board configuration and reset conditions on these pins must be 144 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller considered. In addition, because the JTAG module has integrated ARM Serial Wire Debug, the method for switching between these two operational modes is described below. 4.3.4.1 GPIO Functionality When the microcontroller is reset with either a POR or RST, the JTAG port pins default to their JTAG configurations. The default configuration includes enabling the pull-up resistors (setting GPIOPUR to 1 for PB7 and PC[3:0]) and enabling the alternate hardware function (setting GPIOAFSEL to 1 for PB7 and PC[3:0]) on the JTAG pins. It is possible for software to configure these pins as GPIOs after reset by writing 0s to PB7 and PC[3:0] in the GPIOAFSEL register. If the user does not require the JTAG port for debugging or board-level testing, this provides five more GPIOs for use in the design. Caution – If the JTAG pins are used as GPIOs in a design, PB7 and PC2 cannot have external pull-down resistors connected to both of them at the same time. If both pins are pulled Low during reset, the controller has unpredictable behavior. If this happens, remove one or both of the pull-down resistors, and apply RST or power-cycle the part. It is possible to create a software sequence that prevents the debugger from connecting to the Stellaris microcontroller. If the program code loaded into flash immediately changes the JTAG pins to their GPIO functionality, the debugger may not have enough time to connect and halt the controller before the JTAG pin functionality switches. This may lock the debugger out of the part. This can be avoided with a software routine that restores JTAG functionality based on an external or software trigger. 4.3.4.2 Communication with JTAG/SWD Because the debug clock and the system clock can be running at different frequencies, care must be taken to maintain reliable communication with the JTAG/SWD interface. In the Capture-DR state, the result of the previous transaction, if any, is returned, together with a 3-bit ACK response. Software should check the ACK response to see if the previous operation has completed before initiating a new transaction. Alternatively, if the system clock is at least 8 times faster than the debug clock (TCK or SWCLK), the previous operation has enough time to complete and the ACK bits do not have to be checked. 4.3.4.3 ARM Serial Wire Debug (SWD) In order to seamlessly integrate the ARM Serial Wire Debug (SWD) functionality, a serial-wire debugger must be able to connect to the Cortex-M3 core without having to perform, or have any knowledge of, JTAG cycles. This is accomplished with a SWD preamble that is issued before the SWD session begins. The switching preamble used to enable the SWD interface of the SWJ-DP module starts with the TAP controller in the Test-Logic-Reset state. From here, the preamble sequences the TAP controller through the following states: Run Test Idle, Select DR, Select IR, Capture IR, Exit1 IR, Update IR, Run Test Idle, Select DR, Select IR, Capture IR, Exit1 IR, Update IR, Run Test Idle, Select DR, Select IR, and Test-Logic-Reset states. Stepping through the JTAG TAP Instruction Register (IR) load sequences of the TAP state machine twice without shifting in a new instruction enables the SWD interface and disables the JTAG interface. For more information on this operation and the SWD interface, see the ARM® Debug Interface V5 Architecture Specification. Because this sequence is a valid series of JTAG operations that could be issued, the ARM JTAG TAP controller is not fully compliant to the IEEE Standard 1149.1. This is the only instance where the ARM JTAG TAP controller does not meet full compliance with the specification. Due to the low July 14, 2014 145 Texas Instruments-Production Data JTAG Interface probability of this sequence occurring during normal operation of the TAP controller, it should not affect normal performance of the JTAG interface. 4.4 Initialization and Configuration After a Power-On-Reset or an external reset (RST), the JTAG pins are automatically configured for JTAG communication. No user-defined initialization or configuration is needed. However, if the user application changes these pins to their GPIO function, they must be configured back to their JTAG functionality before JTAG communication can be restored. This is done by enabling the five JTAG pins (PB7 and PC[3:0]) for their alternate function using the GPIOAFSEL register. In addition to enabling the alternate functions, any other changes to the GPIO pad configurations on the five JTAG pins (PB7 andPC[3:0]) should be reverted to their default settings. 4.5 Register Descriptions There are no APB-accessible registers in the JTAG TAP Controller or Shift Register chains. The registers within the JTAG controller are all accessed serially through the TAP Controller. The registers can be broken down into two main categories: Instruction Registers and Data Registers. 4.5.1 Instruction Register (IR) The JTAG TAP Instruction Register (IR) is a four-bit serial scan chain connected between the JTAG TDI and TDO pins with a parallel load register. When the TAP Controller is placed in the correct states, bits can be shifted into the Instruction Register. Once these bits have been shifted into the chain and updated, they are interpreted as the current instruction. The decode of the Instruction Register bits is shown in Table 4-3 on page 146. A detailed explanation of each instruction, along with its associated Data Register, follows. Table 4-3. JTAG Instruction Register Commands 4.5.1.1 IR[3:0] Instruction Description 0000 EXTEST Drives the values preloaded into the Boundary Scan Chain by the SAMPLE/PRELOAD instruction onto the pads. 0001 INTEST Drives the values preloaded into the Boundary Scan Chain by the SAMPLE/PRELOAD instruction into the controller. 0010 SAMPLE / PRELOAD 1000 ABORT Shifts data into the ARM Debug Port Abort Register. 1010 DPACC Shifts data into and out of the ARM DP Access Register. 1011 APACC Shifts data into and out of the ARM AC Access Register. 1110 IDCODE Loads manufacturing information defined by the IEEE Standard 1149.1 into the IDCODE chain and shifts it out. Captures the current I/O values and shifts the sampled values out of the Boundary Scan Chain while new preload data is shifted in. 1111 BYPASS Connects TDI to TDO through a single Shift Register chain. All Others Reserved Defaults to the BYPASS instruction to ensure that TDI is always connected to TDO. EXTEST Instruction The EXTEST instruction is not associated with its own Data Register chain. The EXTEST instruction uses the data that has been preloaded into the Boundary Scan Data Register using the SAMPLE/PRELOAD instruction. When the EXTEST instruction is present in the Instruction Register, the preloaded data in the Boundary Scan Data Register associated with the outputs and output enables are used to drive the GPIO pads rather than the signals coming from the core. This allows 146 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller tests to be developed that drive known values out of the controller, which can be used to verify connectivity. While the EXTEST instruction is present in the Instruction Register, the Boundary Scan Data Register can be accessed to sample and shift out the current data and load new data into the Boundary Scan Data Register. 4.5.1.2 INTEST Instruction The INTEST instruction is not associated with its own Data Register chain. The INTEST instruction uses the data that has been preloaded into the Boundary Scan Data Register using the SAMPLE/PRELOAD instruction. When the INTEST instruction is present in the Instruction Register, the preloaded data in the Boundary Scan Data Register associated with the inputs are used to drive the signals going into the core rather than the signals coming from the GPIO pads. This allows tests to be developed that drive known values into the controller, which can be used for testing. It is important to note that although the RST input pin is on the Boundary Scan Data Register chain, it is only observable. While the INTEXT instruction is present in the Instruction Register, the Boundary Scan Data Register can be accessed to sample and shift out the current data and load new data into the Boundary Scan Data Register. 4.5.1.3 SAMPLE/PRELOAD Instruction The SAMPLE/PRELOAD instruction connects the Boundary Scan Data Register chain between TDI and TDO. This instruction samples the current state of the pad pins for observation and preloads new test data. Each GPIO pad has an associated input, output, and output enable signal. When the TAP controller enters the Capture DR state during this instruction, the input, output, and output-enable signals to each of the GPIO pads are captured. These samples are serially shifted out of TDO while the TAP controller is in the Shift DR state and can be used for observation or comparison in various tests. While these samples of the inputs, outputs, and output enables are being shifted out of the Boundary Scan Data Register, new data is being shifted into the Boundary Scan Data Register from TDI. Once the new data has been shifted into the Boundary Scan Data Register, the data is saved in the parallel load registers when the TAP controller enters the Update DR state. This update of the parallel load register preloads data into the Boundary Scan Data Register that is associated with each input, output, and output enable. This preloaded data can be used with the EXTEST and INTEST instructions to drive data into or out of the controller. Please see “Boundary Scan Data Register” on page 149 for more information. 4.5.1.4 ABORT Instruction The ABORT instruction connects the associated ABORT Data Register chain between TDI and TDO. This instruction provides read and write access to the ABORT Register of the ARM Debug Access Port (DAP). Shifting the proper data into this Data Register clears various error bits or initiates a DAP abort of a previous request. Please see the “ABORT Data Register” on page 149 for more information. 4.5.1.5 DPACC Instruction The DPACC instruction connects the associated DPACC Data Register chain between TDI and TDO. This instruction provides read and write access to the DPACC Register of the ARM Debug Access Port (DAP). Shifting the proper data into this register and reading the data output from this register allows read and write access to the ARM debug and status registers. Please see “DPACC Data Register” on page 149 for more information. July 14, 2014 147 Texas Instruments-Production Data JTAG Interface 4.5.1.6 APACC Instruction The APACC instruction connects the associated APACC Data Register chain between TDI and TDO. This instruction provides read and write access to the APACC Register of the ARM Debug Access Port (DAP). Shifting the proper data into this register and reading the data output from this register allows read and write access to internal components and buses through the Debug Port. Please see “APACC Data Register” on page 149 for more information. 4.5.1.7 IDCODE Instruction The IDCODE instruction connects the associated IDCODE Data Register chain between TDI and TDO. This instruction provides information on the manufacturer, part number, and version of the ARM core. This information can be used by testing equipment and debuggers to automatically configure their input and output data streams. IDCODE is the default instruction that is loaded into the JTAG Instruction Register when a Power-On-Reset (POR) is asserted, TRST is asserted, or the Test-Logic-Reset state is entered. Please see “IDCODE Data Register” on page 148 for more information. 4.5.1.8 BYPASS Instruction The BYPASS instruction connects the associated BYPASS Data Register chain between TDI and TDO. This instruction is used to create a minimum length serial path between the TDI and TDO ports. The BYPASS Data Register is a single-bit shift register. This instruction improves test efficiency by allowing components that are not needed for a specific test to be bypassed in the JTAG scan chain by loading them with the BYPASS instruction. Please see “BYPASS Data Register” on page 149 for more information. 4.5.2 Data Registers The JTAG module contains six Data Registers. These include: IDCODE, BYPASS, Boundary Scan, APACC, DPACC, and ABORT serial Data Register chains. Each of these Data Registers is discussed in the following sections. 4.5.2.1 IDCODE Data Register The format for the 32-bit IDCODE Data Register defined by the IEEE Standard 1149.1 is shown in Figure 4-3 on page 148. The standard requires that every JTAG-compliant device implement either the IDCODE instruction or the BYPASS instruction as the default instruction. The LSB of the IDCODE Data Register is defined to be a 1 to distinguish it from the BYPASS instruction, which has an LSB of 0. This allows auto configuration test tools to determine which instruction is the default instruction. The major uses of the JTAG port are for manufacturer testing of component assembly, and program development and debug. To facilitate the use of auto-configuration debug tools, the IDCODE instruction outputs a value of 0x1BA0.0477. This allows the debuggers to automatically configure themselves to work correctly with the Cortex-M3 during debug. Figure 4-3. IDCODE Register Format 31 TDI 28 27 Version 12 11 Part Number 148 1 0 Manufacturer ID 1 TDO July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 4.5.2.2 BYPASS Data Register The format for the 1-bit BYPASS Data Register defined by the IEEE Standard 1149.1 is shown in Figure 4-4 on page 149. The standard requires that every JTAG-compliant device implement either the BYPASS instruction or the IDCODE instruction as the default instruction. The LSB of the BYPASS Data Register is defined to be a 0 to distinguish it from the IDCODE instruction, which has an LSB of 1. This allows auto configuration test tools to determine which instruction is the default instruction. Figure 4-4. BYPASS Register Format 0 0 TDI 4.5.2.3 TDO Boundary Scan Data Register The format of the Boundary Scan Data Register is shown in Figure 4-5 on page 149. Each GPIO pin, starting with a GPIO pin next to the JTAG port pins, is included in the Boundary Scan Data Register. Each GPIO pin has three associated digital signals that are included in the chain. These signals are input, output, and output enable, and are arranged in that order as can be seen in the figure. When the Boundary Scan Data Register is accessed with the SAMPLE/PRELOAD instruction, the input, output, and output enable from each digital pad are sampled and then shifted out of the chain to be verified. The sampling of these values occurs on the rising edge of TCK in the Capture DR state of the TAP controller. While the sampled data is being shifted out of the Boundary Scan chain in the Shift DR state of the TAP controller, new data can be preloaded into the chain for use with the EXTEST and INTEST instructions. These instructions either force data out of the controller, with the EXTEST instruction, or into the controller, with the INTEST instruction. Figure 4-5. Boundary Scan Register Format TDI I N O U T O E ... GPIO PB6 4.5.2.4 I N O U T GPIO m O E I N RST I N O U T GPIO m+1 O E ... I N O U T O TDO E GPIO n APACC Data Register The format for the 35-bit APACC Data Register defined by ARM is described in the ARM® Debug Interface V5 Architecture Specification. 4.5.2.5 DPACC Data Register The format for the 35-bit DPACC Data Register defined by ARM is described in the ARM® Debug Interface V5 Architecture Specification. 4.5.2.6 ABORT Data Register The format for the 35-bit ABORT Data Register defined by ARM is described in the ARM® Debug Interface V5 Architecture Specification. July 14, 2014 149 Texas Instruments-Production Data System Control 5 System Control System control determines the overall operation of the device. It provides information about the device, controls the clocking to the core and individual peripherals, and handles reset detection and reporting. 5.1 Signal Description Table 5-1 on page 150 lists the external signals of the System Control module and describes the function of each. The NMI signal is the alternate function for and functions as a GPIO after reset. under commit protection and require a special process to be configured as any alternate function or to subsequently return to the GPIO function. The column in the table below titled "Pin Assignment" lists the GPIO pin placement for the NMI signal. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the NMI function. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. The remaining signals (with the word "fixed" in the Pin Assignment column) have a fixed pin assignment and function. Table 5-1. System Control & Clocks Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type Description OSC0 9 I Analog Main oscillator crystal input or an external clock reference input. OSC1 10 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. RST 5 I TTL System reset input. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 5.2 Functional Description The System Control module provides the following capabilities: ■ Device identification (see “Device Identification” on page 150) ■ Local control, such as reset (see “Reset Control” on page 150), power (see “Power Control” on page 155) and clock control (see “Clock Control” on page 155) ■ System control (Run, Sleep, and Deep-Sleep modes); see “System Control” on page 158 5.2.1 Device Identification Several read-only registers provide software with information on the microcontroller, such as version, part number, SRAM size, flash size, and other features. See the DID0, DID1, and DC0-DC4 registers. 5.2.2 Reset Control This section discusses aspects of hardware functions during reset as well as system software requirements following the reset sequence. 5.2.2.1 Reset Sources The controller has six sources of reset: 1. External reset input pin (RST) assertion; see “External RST Pin” on page 152. 150 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 2. Power-on reset (POR); see “Power-On Reset (POR)” on page 151. 3. Internal brown-out (BOR) detector; see “Brown-Out Reset (BOR)” on page 153. 4. Software-initiated reset (with the software reset registers); see “Software Reset” on page 154. 5. A watchdog timer reset condition violation; see “Watchdog Timer Reset” on page 154. 6. Internal low drop-out (LDO) regulator output. Table 5-2 provides a summary of results of the various reset operations. Table 5-2. Reset Sources Core Reset? JTAG Reset? On-Chip Peripherals Reset? Power-On Reset Reset Source Yes Yes Yes RST Yes Pin Config Only Yes Brown-Out Reset Yes No Yes Software System Request a Reset Yes No Yes Software Peripheral Reset No No Yes Watchdog Reset Yes No Yes LDO Reset Yes No Yes b a. By using the SYSRESREQ bit in the ARM Cortex-M3 Application Interrupt and Reset Control (APINT) register b. Programmable on a module-by-module basis using the Software Reset Control Registers. After a reset, the Reset Cause (RESC) register is set with the reset cause. The bits in this register are sticky and maintain their state across multiple reset sequences, except when an external reset is the cause, and then all the other bits in the RESC register are cleared. Note: 5.2.2.2 The main oscillator is used for external resets and power-on resets; the internal oscillator is used during the internal process by internal reset and clock verification circuitry. Power-On Reset (POR) Note: The power-on reset also resets the JTAG controller. An external reset does not. The internal Power-On Reset (POR) circuit monitors the power supply voltage (VDD) and generates a reset signal to all of the internal logic including JTAG when the power supply ramp reaches a threshold value (VTH). The microcontroller must be operating within the specified operating parameters when the on-chip power-on reset pulse is complete. The 3.3-V power supply to the microcontroller must reach 3.0 V within 10 msec of VDD crossing 2.0 V to guarantee proper operation. For applications that require the use of an external reset signal to hold the microcontroller in reset longer than the internal POR, the RST input may be used as discussed in “External RST Pin” on page 152. The Power-On Reset sequence is as follows: 1. The microcontroller waits for internal POR to go inactive. 2. The internal reset is released and the core loads from memory the initial stack pointer, the initial program counter, and the first instruction designated by the program counter, and then begins execution. The internal POR is only active on the initial power-up of the microcontroller. The Power-On Reset timing is shown in Figure 17-6 on page 467. July 14, 2014 151 Texas Instruments-Production Data System Control 5.2.2.3 External RST Pin Note: It is recommended that the trace for the RST signal must be kept as short as possible. Be sure to place any components connected to the RST signal as close to the microcontroller as possible. If the application only uses the internal POR circuit, the RST input must be connected to the power supply (VDD) through an optional pull-up resistor (0 to 100K Ω) as shown in Figure 5-1 on page 152. Figure 5-1. Basic RST Configuration VDD Stellaris® RPU RST RPU = 0 to 100 kΩ The external reset pin (RST) resets the microcontroller including the core and all the on-chip peripherals except the JTAG TAP controller (see “JTAG Interface” on page 140). The external reset sequence is as follows: 1. The external reset pin (RST) is asserted for the duration specified by TMIN and then de-asserted (see “Reset” on page 466). 2. The internal reset is released and the core loads from memory the initial stack pointer, the initial program counter, and the first instruction designated by the program counter, and then begins execution. To improve noise immunity and/or to delay reset at power up, the RST input may be connected to an RC network as shown in Figure 5-2 on page 152. Figure 5-2. External Circuitry to Extend Power-On Reset VDD Stellaris® RPU RST C1 RPU = 1 kΩ to 100 kΩ C1 = 1 nF to 10 µF If the application requires the use of an external reset switch, Figure 5-3 on page 153 shows the proper circuitry to use. 152 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 5-3. Reset Circuit Controlled by Switch VDD Stellaris® RPU RST C1 RS Typical RPU = 10 kΩ Typical RS = 470 Ω C1 = 10 nF The RPU and C1 components define the power-on delay. The external reset timing is shown in Figure 17-5 on page 466. 5.2.2.4 Brown-Out Reset (BOR) A drop in the input voltage resulting in the assertion of the internal brown-out detector can be used to reset the controller. This is initially disabled and may be enabled by software. The system provides a brown-out detection circuit that triggers if the power supply (VDD) drops below a brown-out threshold voltage (VBTH). The circuit is provided to guard against improper operation of logic and peripherals that operate off the power supply voltage (VDD) and not the LDO voltage. If a brown-out condition is detected, the system may generate a controller interrupt or a system reset. The BOR circuit has a digital filter that protects against noise-related detection for the interrupt condition. This feature may be optionally enabled. Brown-out resets are controlled with the Power-On and Brown-Out Reset Control (PBORCTL) register. The BORIOR bit in the PBORCTL register must be set for a brown-out condition to trigger a reset. The brown-out reset sequence is as follows: 1. When VDD drops below VBTH, an internal BOR condition is set. 2. If the BORWT bit in the PBORCTL register is set and BORIOR is not set, the BOR condition is resampled, after a delay specified by BORTIM, to determine if the original condition was caused by noise. If the BOR condition is not met the second time, then no further action is taken. 3. If the BOR condition exists, an internal reset is asserted. 4. The internal reset is released and the controller fetches and loads the initial stack pointer, the initial program counter, the first instruction designated by the program counter, and begins execution. 5. The internal BOR condition is reset after 500 µs to prevent another BOR condition from being set before software has a chance to investigate the original cause. The internal Brown-Out Reset timing is shown in Figure 17-7 on page 467. July 14, 2014 153 Texas Instruments-Production Data System Control 5.2.2.5 Software Reset Software can reset a specific peripheral or generate a reset to the entire system . Peripherals can be individually reset by software via three registers that control reset signals to each peripheral (see the SRCRn registers). If the bit position corresponding to a peripheral is set and subsequently cleared, the peripheral is reset. The encoding of the reset registers is consistent with the encoding of the clock gating control for peripherals and on-chip functions (see “System Control” on page 158). Note that all reset signals for all clocks of the specified unit are asserted as a result of a software-initiated reset. The entire system can be reset by software by setting the SYSRESETREQ bit in the Cortex-M3 Application Interrupt and Reset Control register resets the entire system including the core. The software-initiated system reset sequence is as follows: 1. A software system reset is initiated by writing the SYSRESETREQ bit in the ARM Cortex-M3 Application Interrupt and Reset Control register. 2. An internal reset is asserted. 3. The internal reset is deasserted and the controller loads from memory the initial stack pointer, the initial program counter, and the first instruction designated by the program counter, and then begins execution. The software-initiated system reset timing is shown in Figure 17-8 on page 467. 5.2.2.6 Watchdog Timer Reset The watchdog timer module's function is to prevent system hangs. The watchdog timer can be configured to generate an interrupt to the controller on its first time-out, and to generate a reset signal on its second time-out. After the first time-out event, the 32-bit counter is reloaded with the value of the Watchdog Timer Load (WDTLOAD) register, and the timer resumes counting down from that value. If the timer counts down to its zero state again before the first time-out interrupt is cleared, and the reset signal has been enabled, the watchdog timer asserts its reset signal to the system. The watchdog timer reset sequence is as follows: 1. The watchdog timer times out for the second time without being serviced. 2. An internal reset is asserted. 3. The internal reset is released and the controller loads from memory the initial stack pointer, the initial program counter, the first instruction designated by the program counter, and begins execution. The watchdog reset timing is shown in Figure 17-9 on page 468. 5.2.2.7 Low Drop-Out (LDO) A reset can be initiated when the internal low drop-out (LDO) regulator output goes unregulated. This is initially disabled and may be enabled by software. LDO is controlled with the LDO Power Control (LDOPCTL) register. The LDO reset sequence is as follows: 1. LDO goes unregulated and the LDOARST bit in the LDOARST register is set. 2. An internal reset is asserted. 154 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 3. The internal reset is released and the controller fetches and loads the initial stack pointer, the initial program counter, the first instruction designated by the program counter, and begins execution. The LDO reset timing is shown in Figure 17-10 on page 468. 5.2.3 Power Control ® The Stellaris microcontroller provides an integrated LDO regulator that is used to provide power to the majority of the controller's internal logic. For power reduction, the LDO regulator provides software a mechanism to adjust the regulated value, in small increments (VSTEP), over the range of 2.25 V to 2.75 V (inclusive)—or 2.5 V ± 10%. The adjustment is made by changing the value of the VADJ field in the LDO Power Control (LDOPCTL) register. 5.2.4 Clock Control System control determines the control of clocks in this part. 5.2.4.1 Fundamental Clock Sources There are multiple clock sources for use in the device: ■ Internal Oscillator (IOSC). The internal oscillator is an on-chip clock source. It does not require the use of any external components. The frequency of the internal oscillator is 12 MHz ± 30%. ■ Main Oscillator (MOSC). The main oscillator provides a frequency-accurate clock source by one of two means: an external single-ended clock source is connected to the OSC0 input pin, or an external crystal is connected across the OSC0 input and OSC1 output pins. The crystal value allowed depends on whether the main oscillator is used as the clock reference source to the PLL. If so, the crystal must be one of the supported frequencies between 3.579545 MHz through 8.192 MHz (inclusive). If the PLL is not being used, the crystal may be any one of the supported frequencies between 1 MHz and 8.192 MHz. The single-ended clock source range is from DC through the specified speed of the device. The supported crystals are listed in the XTAL bit field in the RCC register (see page 170). The internal system clock (SysClk), is derived from any of the above sources plus two others: the output of the main internal PLL, and the internal oscillator divided by four (3 MHz ± 30%). The frequency of the PLL clock reference must be in the range of 3.579545 MHz to 8.192 MHz (inclusive). Table 5-3 on page 155 shows how the various clock sources can be used in a system. Table 5-3. Clock Source Options 5.2.4.2 Clock Source Drive PLL? Internal Oscillator (12 MHz) Yes BYPASS = 0, OSCSRC = 0x1 Yes BYPASS = 1, OSCSRC = 0x1 Internal Oscillator divide by 4 (3 Yes MHz) BYPASS = 0, OSCSRC = 0x2 Yes BYPASS = 1, OSCSRC = 0x2 Main Oscillator BYPASS = 0, OSCSRC = 0x0 Yes BYPASS = 1, OSCSRC = 0x0 Yes Used as SysClk? Clock Configuration Nearly all of the control for the clocks is provided by the Run-Mode Clock Configuration (RCC) register. This register controls the following clock functionality: ■ Source of clocks in sleep and deep-sleep modes July 14, 2014 155 Texas Instruments-Production Data System Control ■ System clock derived from PLL or other clock source ■ Enabling/disabling of oscillators and PLL ■ Clock divisors ■ Crystal input selection Figure 5-4 on page 156 shows the logic for the main clock tree. The peripheral blocks are driven by the system clock signal and can be individually enabled/disabled. Figure 5-4. Main Clock Tree USESYSDIVa OSC1 OSC2 Main Osc 1-8 MHz System Clock SYSDIVa Internal Osc 12 MHz PLL (200 MHz output) ÷4 OSCSRCa OENa BYPASSa a XTAL PWRDNa a. These are bit fields within the Run-Mode Clock Configuration (RCC) register. In the RCC register, the SYSDIV field specifies which divisor is used to generate the system clock from either the PLL output or the oscillator source (depending on how the BYPASS bit in this register is configured). Table 5-4 shows how the SYSDIV encoding affects the system clock frequency, depending on whether the PLL is used (BYPASS=0) or another clock source is used (BYPASS=1). The divisor is equivalent to the SYSDIV encoding plus 1. For a list of possible clock sources, see Table 5-3 on page 155. Table 5-4. Possible System Clock Frequencies Using the SYSDIV Field SYSDIV Divisor a Frequency (BYPASS=0) Frequency (BYPASS=1) StellarisWare Parameter b 0x0 /1 reserved Clock source frequency/2 SYSCTL_SYSDIV_1 0x1 /2 reserved Clock source frequency/2 SYSCTL_SYSDIV_2 0x2 /3 reserved Clock source frequency/3 SYSCTL_SYSDIV_3 0x3 /4 50 MHz Clock source frequency/4 SYSCTL_SYSDIV_4 0x4 /5 40 MHz Clock source frequency/5 SYSCTL_SYSDIV_5 0x5 /6 33.33 MHz Clock source frequency/6 SYSCTL_SYSDIV_6 0x6 /7 28.57 MHz Clock source frequency/7 SYSCTL_SYSDIV_7 0x7 /8 25 MHz Clock source frequency/8 SYSCTL_SYSDIV_8 0x8 /9 22.22 MHz Clock source frequency/9 SYSCTL_SYSDIV_9 0x9 /10 20 MHz Clock source frequency/10 SYSCTL_SYSDIV_10 0xA /11 18.18 MHz Clock source frequency/11 SYSCTL_SYSDIV_11 0xB /12 16.67 MHz Clock source frequency/12 SYSCTL_SYSDIV_12 156 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 5-4. Possible System Clock Frequencies Using the SYSDIV Field (continued) a Divisor Frequency (BYPASS=0) Frequency (BYPASS=1) StellarisWare Parameter 0xC /13 15.38 MHz Clock source frequency/13 SYSCTL_SYSDIV_13 0xD /14 14.29 MHz Clock source frequency/14 SYSCTL_SYSDIV_14 0xE /15 13.33 MHz Clock source frequency/15 SYSCTL_SYSDIV_15 0xF /16 12.5 MHz (default) Clock source frequency/16 SYSCTL_SYSDIV_16 SYSDIV a. This parameter is used in functions such as SysCtlClockSet() in the Stellaris Peripheral Driver Library. b. SYSCTL_SYSDIV_1 does not set the USESYSDIV bit. As a result, using this parameter without enabling the PLL results in the system clock having the same frequency as the clock source. 5.2.4.3 Crystal Configuration for the Main Oscillator (MOSC) The main oscillator supports the use of a select number of crystals. If the main oscillator is used by the PLL as a reference clock, the supported range of crystals is 3.579545 to 8.192 MHz, otherwise, the range of supported crystals is 1 to 8.192 MHz. The XTAL bit in the RCC register (see page 170) describes the available crystal choices and default programming values. Software configures the RCC register XTAL field with the crystal number. If the PLL is used in the design, the XTAL field value is internally translated to the PLL settings. 5.2.4.4 Main PLL Frequency Configuration The main PLL is disabled by default during power-on reset and is enabled later by software if required. Software configures the main PLL input reference clock source, specifies the output divisor to set the system clock frequency, and enables the main PLL to drive the output. If the main oscillator provides the clock reference to the main PLL, the translation provided by hardware and used to program the PLL is available for software in the XTAL to PLL Translation (PLLCFG) register (see page 173). The internal translation provides a translation within ± 1% of the targeted PLL VCO frequency. The Crystal Value field (XTAL) in the Run-Mode Clock Configuration (RCC) register (see page 170) describes the available crystal choices and default programming of the PLLCFG register. Any time the XTAL field changes, the new settings are translated and the internal PLL settings are updated. 5.2.4.5 PLL Modes The PLL has two modes of operation: Normal and Power-Down ■ Normal: The PLL multiplies the input clock reference and drives the output. ■ Power-Down: Most of the PLL internal circuitry is disabled and the PLL does not drive the output. The modes are programmed using the RCC register fields (see page 170). 5.2.4.6 PLL Operation If a PLL configuration is changed, the PLL output frequency is unstable until it reconverges (relocks) to the new setting. The time between the configuration change and relock is TREADY (see Table 17-7 on page 464). During the relock time, the affected PLL is not usable as a clock reference. PLL is changed by one of the following: ■ Change to the XTAL value in the RCC register—writes of the same value do not cause a relock. July 14, 2014 157 Texas Instruments-Production Data System Control ■ Change in the PLL from Power-Down to Normal mode. A counter is defined to measure the TREADY requirement. The counter is clocked by the main oscillator. The range of the main oscillator has been taken into account and the down counter is set to 0x1200 (that is, ~600 μs at an 8.192 MHz external oscillator clock). Hardware is provided to keep the PLL from being used as a system clock until the TREADY condition is met after one of the two changes above. It is the user's responsibility to have a stable clock source (like the main oscillator) before the RCC register is switched to use the PLL. If the main PLL is enabled and the system clock is switched to use the PLL in one step, the system control hardware continues to clock the controller from the oscillator selected by the RCC register until the main PLL is stable (TREADY time met), after which it changes to the PLL. Software can use many methods to ensure that the system is clocked from the main PLL, including periodically polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register, and enabling the PLL Lock interrupt. 5.2.4.7 Clock Verification Timers There are three identical clock verification circuits that can be enabled though software. The circuit checks the faster clock by a slower clock using timers: ■ The main oscillator checks the PLL. ■ The main oscillator checks the internal oscillator. ■ The internal oscillator divided by 64 checks the main oscillator. If the verification timer function is enabled and a failure is detected, the main clock tree is immediately switched to a working clock and an interrupt is generated to the controller. Software can then determine the course of action to take. The actual failure indication and clock switching does not clear without a write to the CLKVCLR register, an external reset, or a POR reset. The clock verification timers are controlled by the PLLVER , IOSCVER , and MOSCVER bits in the RCC register. 5.2.5 System Control For power-savings purposes, the RCGCn , SCGCn , and DCGCn registers control the clock gating logic for each peripheral or block in the system while the controller is in Run, Sleep, and Deep-Sleep mode, respectively. The DC1 , DC2 and DC4 registers act as a write mask for the RCGCn , SCGCn, and DCGCn registers. There are three levels of operation for the device defined as: ■ Run Mode. In Run mode, the controller actively executes code. Run mode provides normal operation of the processor and all of the peripherals that are currently enabled by the RCGCn registers. The system clock can be any of the available clock sources including the PLL. ■ Sleep Mode. In Sleep mode, the clock frequency of the active peripherals is unchanged, but the processor and the memory subsystem are not clocked and therefore no longer execute code. Sleep mode is entered by the Cortex-M3 core executing a WFI(Wait for Interrupt) instruction. Any properly configured interrupt event in the system will bring the processor back into Run mode. See “Power Management” on page 76 for more details. Peripherals are clocked that are enabled in the SCGCn register when auto-clock gating is enabled (see the RCC register) or the RCGCn register when the auto-clock gating is disabled. The system clock has the same source and frequency as that during Run mode. 158 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller ■ Deep-Sleep Mode. In Deep-Sleep mode, the clock frequency of the active peripherals may change (depending on the Run mode clock configuration) in addition to the processor clock being stopped. An interrupt returns the device to Run mode from one of the sleep modes. Deep-Sleep mode is entered by first writing the Deep Sleep Enable bit in the ARM Cortex-M3 NVIC system control register and then executing a WFI instruction. Any properly configured interrupt event in the system will bring the processor back into Run mode. See “Power Management” on page 76 for more details. The Cortex-M3 processor core and the memory subsystem are not clocked. Peripherals are clocked that are enabled in the DCGCn register when auto-clock gating is enabled (see the RCC register) or the RCGCn register when auto-clock gating is disabled. The system clock source is the main oscillator by default or the internal oscillator specified in the DSLPCLKCFG register if one is enabled. When the DSLPCLKCFG register is used, the internal oscillator is powered up, if necessary, and the main oscillator is powered down. If the PLL is running at the time of the WFI instruction, hardware will power the PLL down. When the Deep-Sleep exit event occurs, hardware brings the system clock back to the source and frequency it had at the onset of Deep-Sleep mode before enabling the clocks that had been stopped during the Deep-Sleep duration. Caution – If the Cortex-M3 Debug Access Port (DAP) has been enabled, and the device wakes from a low power sleep or deep-sleep mode, the core may start executing code before all clocks to peripherals have been restored to their run mode configuration. The DAP is usually enabled by software tools accessing the JTAG or SWD interface when debugging or flash programming. If this condition occurs, a Hard Fault is triggered when software accesses a peripheral with an invalid clock. A software delay loop can be used at the beginning of the interrupt routine that is used to wake up a system from a WFI (Wait For Interrupt) instruction. This stalls the execution of any code that accesses a peripheral register that might cause a fault. This loop can be removed for production software as the DAP is most likely not enabled during normal execution. Because the DAP is disabled by default (power on reset), the user can also power-cycle the device. The DAP is not enabled unless it is enabled through the JTAG or SWD interface. 5.3 Initialization and Configuration The PLL is configured using direct register writes to the RCC register. The steps required to successfully change the PLL-based system clock are: 1. Bypass the PLL and system clock divider by setting the BYPASS bit and clearing the USESYS bit in the RCC register. This configures the system to run off a “raw” clock source and allows for the new PLL configuration to be validated before switching the system clock to the PLL. 2. Select the crystal value (XTAL) and oscillator source (OSCSRC), and clear the PWRDN and OEN bits in RCC. Setting the XTAL field automatically pulls valid PLL configuration data for the appropriate crystal, and clearing the PWRDN and OEN bits powers and enables the PLL and its output. 3. Select the desired system divider (SYSDIV) in RCC and set the USESYS bit in RCC. The SYSDIV field determines the system frequency for the microcontroller. 4. Wait for the PLL to lock by polling the PLLLRIS bit in the Raw Interrupt Status (RIS) register. 5. Enable use of the PLL by clearing the BYPASS bit in RCC. July 14, 2014 159 Texas Instruments-Production Data System Control Note: 5.4 If the BYPASS bit is cleared before the PLL locks, it is possible to render the device unusable. Register Map Table 5-5 on page 160 lists the System Control registers, grouped by function. The offset listed is a hexadecimal increment to the register's address, relative to the System Control base address of 0x400F.E000. Note: Spaces in the System Control register space that are not used are reserved for future or internal use. Software should not modify any reserved memory address. Table 5-5. System Control Register Map Description See page Offset Name Type Reset 0x000 DID0 RO - Device Identification 0 162 0x004 DID1 RO - Device Identification 1 177 0x008 DC0 RO 0x001F.000F Device Capabilities 0 179 0x010 DC1 RO 0x0000.309F Device Capabilities 1 180 0x014 DC2 RO 0x0707.1013 Device Capabilities 2 182 0x018 DC3 RO 0xBF00.7FC0 Device Capabilities 3 184 0x01C DC4 RO 0x0000.001F Device Capabilities 4 186 0x030 PBORCTL R/W 0x0000.7FFD Power-On and Brown-Out Reset Control 164 0x034 LDOPCTL R/W 0x0000.0000 LDO Power Control 165 0x040 SRCR0 R/W 0x00000000 Software Reset Control 0 201 0x044 SRCR1 R/W 0x00000000 Software Reset Control 1 202 0x048 SRCR2 R/W 0x00000000 Software Reset Control 2 204 0x050 RIS RO 0x0000.0000 Raw Interrupt Status 166 0x054 IMC R/W 0x0000.0000 Interrupt Mask Control 167 0x058 MISC R/W1C 0x0000.0000 Masked Interrupt Status and Clear 168 0x05C RESC R/W - Reset Cause 169 0x060 RCC R/W 0x0780.3AC0 Run-Mode Clock Configuration 170 0x064 PLLCFG RO - XTAL to PLL Translation 173 0x100 RCGC0 R/W 0x00000040 Run Mode Clock Gating Control Register 0 187 0x104 RCGC1 R/W 0x00000000 Run Mode Clock Gating Control Register 1 190 0x108 RCGC2 R/W 0x00000000 Run Mode Clock Gating Control Register 2 196 0x110 SCGC0 R/W 0x00000040 Sleep Mode Clock Gating Control Register 0 188 0x114 SCGC1 R/W 0x00000000 Sleep Mode Clock Gating Control Register 1 192 0x118 SCGC2 R/W 0x00000000 Sleep Mode Clock Gating Control Register 2 197 0x120 DCGC0 R/W 0x00000040 Deep Sleep Mode Clock Gating Control Register 0 189 160 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 5-5. System Control Register Map (continued) Name Type Reset 0x124 DCGC1 R/W 0x00000000 Deep Sleep Mode Clock Gating Control Register 1 194 0x128 DCGC2 R/W 0x00000000 Deep Sleep Mode Clock Gating Control Register 2 199 0x144 DSLPCLKCFG R/W 0x0780.0000 Deep Sleep Clock Configuration 174 0x150 CLKVCLR R/W 0x0000.0000 Clock Verification Clear 175 0x160 LDOARST R/W 0x0000.0000 Allow Unregulated LDO to Reset the Part 176 5.5 Description See page Offset Register Descriptions All addresses given are relative to the System Control base address of 0x400F.E000. July 14, 2014 161 Texas Instruments-Production Data System Control Register 1: Device Identification 0 (DID0), offset 0x000 This register identifies the version of the microcontroller. Each microcontroller is uniquely identified by the combined values of the CLASS field in the DID0 register and the PARTNO field in the DID1 register. Device Identification 0 (DID0) Base 0x400F.E000 Offset 0x000 Type RO, reset 31 30 reserved Type Reset 29 28 27 26 25 24 23 22 VER 21 20 19 18 17 16 reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - RO - MAJOR Type Reset MINOR Bit/Field Name Type Reset 31 reserved RO 0 30:28 VER RO 0x0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. DID0 Version This field defines the DID0 register format version. The version number is numeric. The value of the VER field is encoded as follows: Value Description 0x0 27:16 reserved RO 0x0 15:8 MAJOR RO - Initial DID0 register format definition for Stellaris® Sandstorm-class devices. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Major Revision This field specifies the major revision number of the device. The major revision reflects changes to base layers of the design. The major revision number is indicated in the part number as a letter (A for first revision, B for second, and so on). This field is encoded as follows: Value Description 0x0 Revision A (initial device) 0x1 Revision B (first base layer revision) 0x2 Revision C (second base layer revision) and so on. 162 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 7:0 MINOR RO - Description Minor Revision This field specifies the minor revision number of the device. The minor revision reflects changes to the metal layers of the design. The MINOR field value is reset when the MAJOR field is changed. This field is numeric and is encoded as follows: Value Description 0x0 Initial device, or a major revision update. 0x1 First metal layer change. 0x2 Second metal layer change. and so on. July 14, 2014 163 Texas Instruments-Production Data System Control Register 2: Power-On and Brown-Out Reset Control (PBORCTL), offset 0x030 This register is responsible for controlling reset conditions after initial power-on reset. Power-On and Brown-Out Reset Control (PBORCTL) Base 0x400F.E000 Offset 0x030 Type R/W, reset 0x0000.7FFD 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 R/W 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BORIOR BORWT R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 0 R/W 1 reserved Type Reset BORTIM Type Reset Bit/Field Name Type Reset 31:16 reserved RO 0x0 15:2 BORTIM R/W 0x1FFF Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. BOR Time Delay This field specifies the number of internal oscillator clocks delayed before the BOR output is resampled if the BORWT bit is set. The width of this field is derived by the t BOR width of 500 μs and the internal oscillator (IOSC) frequency of 12 MHz ± 30%. At +30%, the counter value has to exceed 7,800. 1 BORIOR R/W 0 BOR Interrupt or Reset This bit controls how a BOR event is signaled to the controller. If set, a reset is signaled. Otherwise, an interrupt is signaled. 0 BORWT R/W 1 BOR Wait and Check for Noise This bit specifies the response to a brown-out signal assertion if BORIOR is not set. If BORWT is set to 1 and BORIOR is cleared to 0, the controller waits BORTIM IOSC periods and resamples the BOR output. If still asserted, a BOR interrupt is signalled. If no longer asserted, the initial assertion is suppressed (attributable to noise). If BORWT is 0, BOR assertions do not resample the output and any condition is reported immediately if enabled. 164 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 3: LDO Power Control (LDOPCTL), offset 0x034 The VADJ field in this register adjusts the on-chip output voltage (VOUT). LDO Power Control (LDOPCTL) Base 0x400F.E000 Offset 0x034 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 VADJ Bit/Field Name Type Reset 31:6 reserved RO 0 5:0 VADJ R/W 0x0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. LDO Output Voltage This field sets the on-chip output voltage. The programming values for the VADJ field are provided below. Value VOUT (V) 0x00 2.50 0x01 2.45 0x02 2.40 0x03 2.35 0x04 2.30 0x05 2.25 0x06-0x3F Reserved 0x1B 2.75 0x1C 2.70 0x1D 2.65 0x1E 2.60 0x1F 2.55 July 14, 2014 165 Texas Instruments-Production Data System Control Register 4: Raw Interrupt Status (RIS), offset 0x050 Central location for system control raw interrupts. These are set and cleared by hardware. Raw Interrupt Status (RIS) Base 0x400F.E000 Offset 0x050 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 PLLLRIS CLRIS IOFRIS MOFRIS LDORIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 BORRIS PLLFRIS RO 0 RO 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 PLLLRIS RO 0 PLL Lock Raw Interrupt Status This bit is set when the PLL TREADY Timer asserts. 5 CLRIS RO 0 Current Limit Raw Interrupt Status This bit is set if the LDO’s CLE output asserts. 4 IOFRIS RO 0 Internal Oscillator Fault Raw Interrupt Status This bit is set if an internal oscillator fault is detected. 3 MOFRIS RO 0 Main Oscillator Fault Raw Interrupt Status This bit is set if a main oscillator fault is detected. 2 LDORIS RO 0 LDO Power Unregulated Raw Interrupt Status This bit is set if a LDO voltage is unregulated. 1 BORRIS RO 0 Brown-Out Reset Raw Interrupt Status This bit is the raw interrupt status for any brown-out conditions. If set, a brown-out condition is currently active. This is an unregistered signal from the brown-out detection circuit. An interrupt is reported if the BORIM bit in the IMC register is set and the BORIOR bit in the PBORCTL register is cleared. 0 PLLFRIS RO 0 PLL Fault Raw Interrupt Status This bit is set if a PLL fault is detected (stops oscillating). 166 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: Interrupt Mask Control (IMC), offset 0x054 Central location for system control interrupt masks. Interrupt Mask Control (IMC) Base 0x400F.E000 Offset 0x054 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 PLLLIM CLIM IOFIM MOFIM LDOIM BORIM PLLFIM RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 PLLLIM R/W 0 PLL Lock Interrupt Mask This bit specifies whether a PLL Lock interrupt is promoted to a controller interrupt. If set, an interrupt is generated if PLLLRIS in RIS is set; otherwise, an interrupt is not generated. 5 CLIM R/W 0 Current Limit Interrupt Mask This bit specifies whether a current limit detection is promoted to a controller interrupt. If set, an interrupt is generated if CLRIS is set; otherwise, an interrupt is not generated. 4 IOFIM R/W 0 Internal Oscillator Fault Interrupt Mask This bit specifies whether an internal oscillator fault detection is promoted to a controller interrupt. If set, an interrupt is generated if IOFRIS is set; otherwise, an interrupt is not generated. 3 MOFIM R/W 0 Main Oscillator Fault Interrupt Mask This bit specifies whether a main oscillator fault detection is promoted to a controller interrupt. If set, an interrupt is generated if MOFRIS is set; otherwise, an interrupt is not generated. 2 LDOIM R/W 0 LDO Power Unregulated Interrupt Mask This bit specifies whether an LDO unregulated power situation is promoted to a controller interrupt. If set, an interrupt is generated if LDORIS is set; otherwise, an interrupt is not generated. 1 BORIM R/W 0 Brown-Out Reset Interrupt Mask This bit specifies whether a brown-out condition is promoted to a controller interrupt. If set, an interrupt is generated if BORRIS is set; otherwise, an interrupt is not generated. 0 PLLFIM R/W 0 PLL Fault Interrupt Mask This bit specifies whether a PLL fault detection is promoted to a controller interrupt. If set, an interrupt is generated if PLLFRIS is set; otherwise, an interrupt is not generated. July 14, 2014 167 Texas Instruments-Production Data System Control Register 6: Masked Interrupt Status and Clear (MISC), offset 0x058 On a read, this register gives the current masked status value of the corresponding interrupt. All of the bits are R/W1C and this action also clears the corresponding raw interrupt bit in the RIS register (see page 166). Masked Interrupt Status and Clear (MISC) Base 0x400F.E000 Offset 0x058 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 PLLLMIS CLMIS IOFMIS RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset RO 0 MOFMIS LDOMIS R/W1C 0 R/W1C 0 BORMIS reserved R/W1C 0 RO 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 PLLLMIS R/W1C 0 PLL Lock Masked Interrupt Status This bit is set when the PLL TREADY timer asserts. The interrupt is cleared by writing a 1 to this bit. 5 CLMIS R/W1C 0 Current Limit Masked Interrupt Status This bit is set if the LDO’s CLE output asserts. The interrupt is cleared by writing a 1 to this bit. 4 IOFMIS R/W1C 0 Internal Oscillator Fault Masked Interrupt Status This bit is set if an internal oscillator fault is detected. The interrupt is cleared by writing a 1 to this bit. 3 MOFMIS R/W1C 0 Main Oscillator Fault Masked Interrupt Status This bit is set if a main oscillator fault is detected. The interrupt is cleared by writing a 1 to this bit. 2 LDOMIS R/W1C 0 LDO Power Unregulated Masked Interrupt Status This bit is set if LDO power is unregulated. The interrupt is cleared by writing a 1 to this bit. 1 BORMIS R/W1C 0 BOR Masked Interrupt Status This bit is the masked interrupt status for any brown-out conditions. If set, a brown-out condition was detected. An interrupt is reported if the BORIM bit in the IMC register is set and the BORIOR bit in the PBORCTL register is cleared. The interrupt is cleared by writing a 1 to this bit. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 168 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 7: Reset Cause (RESC), offset 0x05C This field specifies the cause of the reset event to software. The reset value is determined by the cause of the reset. When an external reset is the cause (EXT is set), all other reset bits are cleared. However, if the reset is due to any other cause, the remaining bits are sticky, allowing software to see all causes. Reset Cause (RESC) Base 0x400F.E000 Offset 0x05C Type R/W, reset 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 LDO SW WDT BOR POR EXT RO 0 RO 0 RO 0 R/W - R/W - R/W - R/W - R/W - R/W - reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5 LDO R/W - LDO Reset When set, indicates the LDO circuit has lost regulation and has generated a reset event. 4 SW R/W - Software Reset When set, indicates a software reset is the cause of the reset event. 3 WDT R/W - Watchdog Timer Reset When set, indicates a watchdog reset is the cause of the reset event. 2 BOR R/W - Brown-Out Reset When set, indicates a brown-out reset is the cause of the reset event. 1 POR R/W - Power-On Reset When set, indicates a power-on reset is the cause of the reset event. 0 EXT R/W - External Reset When set, indicates an external reset (RST assertion) is the cause of the reset event. July 14, 2014 169 Texas Instruments-Production Data System Control Register 8: Run-Mode Clock Configuration (RCC), offset 0x060 This register is defined to provide source control and frequency speed. Run-Mode Clock Configuration (RCC) Base 0x400F.E000 Offset 0x060 Type R/W, reset 0x0780.3AC0 31 30 29 28 26 25 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 1 15 14 13 12 11 10 PWRDN OEN BYPASS PLLVER R/W 1 R/W 1 R/W 1 R/W 0 reserved Type Reset reserved Type Reset RO 0 RO 0 27 24 23 R/W 1 R/W 1 R/W 1 9 8 R/W 1 R/W 0 ACG 21 20 19 R/W 0 RO 0 RO 0 RO 0 7 6 5 4 3 R/W 1 R/W 1 R/W 0 SYSDIV 22 Name Type Reset 31:28 reserved RO 0x0 27 ACG R/W 0 17 16 RO 0 RO 0 RO 0 2 1 0 reserved USESYSDIV XTAL Bit/Field 18 OSCSRC R/W 0 IOSCVER MOSCVER IOSCDIS MOSCDIS R/W 0 R/W 0 R/W 0 R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Auto Clock Gating This bit specifies whether the system uses the Sleep-Mode Clock Gating Control (SCGCn) registers and Deep-Sleep-Mode Clock Gating Control (DCGCn) registers if the controller enters a Sleep or Deep-Sleep mode (respectively). If set, the SCGCn or DCGCn registers are used to control the clocks distributed to the peripherals when the controller is in a sleep mode. Otherwise, the Run-Mode Clock Gating Control (RCGCn) registers are used when the controller enters a sleep mode. The RCGCn registers are always used to control the clocks in Run mode. This allows peripherals to consume less power when the controller is in a sleep mode and the peripheral is unused. 26:23 SYSDIV R/W 0xF System Clock Divisor Specifies which divisor is used to generate the system clock from either the PLL output or the oscillator source (depending on how the BYPASS bit in this register is configured). See Table 5-4 on page 156 for bit encodings. The PLL VCO frequency is 200 MHz. If the SYSDIV value is less than MINSYSDIV (see page 180), and the PLL is being used, then the MINSYSDIV value is used as the divisor. If the PLL is not being used, the SYSDIV value can be less than MINSYSDIV. 22 USESYSDIV R/W 0 Enable System Clock Divider Use the system clock divider as the source for the system clock. The system clock divider is forced to be used when the PLL is selected as the source. If the USERCC2 bit in the RCC2 register is set, then the SYSDIV2 field in the RCC2 register is used as the system clock divider rather than the SYSDIV field in this register. 170 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset Description 21:14 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 13 PWRDN R/W 1 PLL Power Down This bit connects to the PLL PWRDN input. The reset value of 1 powers down the PLL. See Table 5-6 on page 172 for PLL mode control. 12 OEN R/W 1 PLL Output Enable This bit specifies whether the PLL output driver is enabled. If cleared, the driver transmits the PLL clock to the output. Otherwise, the PLL clock does not oscillate outside the PLL module. Note: 11 BYPASS R/W 1 Both PWRDN and OEN must be cleared to run the PLL. PLL Bypass Chooses whether the system clock is derived from the PLL output or the OSC source. If set, the clock that drives the system is the OSC source. Otherwise, the clock that drives the system is the PLL output clock divided by the system divider. See Table 5-4 on page 156 for programming guidelines. 10 PLLVER R/W 0 PLL Verification This bit controls the PLL verification timer function. If set, the verification timer is enabled and an interrupt is generated if the PLL becomes inoperative. Otherwise, the verification timer is not enabled. 9:6 XTAL R/W 0xB Crystal Value This field specifies the crystal value attached to the main oscillator. The encoding for this field is provided below. Value Crystal Frequency (MHz) Not Using the PLL Crystal Frequency (MHz) Using the PLL 0x0 1.000 reserved 0x1 1.8432 reserved 0x2 2.000 reserved 0x3 2.4576 reserved 0x4 3.579545 MHz 0x5 3.6864 MHz 0x6 4 MHz 0x7 4.096 MHz 0x8 4.9152 MHz 0x9 5 MHz 0xA 5.12 MHz 0xB 6 MHz (reset value) 0xC 6.144 MHz 0xD 7.3728 MHz 0xE 8 MHz 0xF 8.192 MHz July 14, 2014 171 Texas Instruments-Production Data System Control Bit/Field Name Type Reset 5:4 OSCSRC R/W 0x0 Description Oscillator Source Selects the input source for the OSC. The values are: Value Input Source 0x0 MOSC Main oscillator (default) 0x1 IOSC Internal oscillator 0x2 IOSC/4 Internal oscillator / 4 (this is necessary if used as input to PLL) 0x3 3 IOSCVER R/W 0 reserved Internal Oscillator Verification Timer This bit controls the internal oscillator verification timer function. If set, the verification timer is enabled and an interrupt is generated if the timer becomes inoperative. Otherwise, the verification timer is not enabled. 2 MOSCVER R/W 0 Main Oscillator Verification Timer This bit controls the main oscillator verification timer function. If set, the verification timer is enabled and an interrupt is generated if the timer becomes inoperative. Otherwise, the verification timer is not enabled. 1 IOSCDIS R/W 0 Internal Oscillator Disable 0: Internal oscillator (IOSC) is enabled. 1: Internal oscillator is disabled. 0 MOSCDIS R/W 0 Main Oscillator Disable 0: Main oscillator is enabled (default). 1: Main oscillator is disabled . Table 5-6. PLL Mode Control PWRDN OEN Mode 1 X Power down 0 0 Normal 172 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 9: XTAL to PLL Translation (PLLCFG), offset 0x064 This register provides a means of translating external crystal frequencies into the appropriate PLL settings. This register is initialized during the reset sequence and updated anytime that the XTAL field changes in the Run-Mode Clock Configuration (RCC) register (see page 170). The PLL frequency is calculated using the PLLCFG field values, as follows: PLLFreq = OSCFreq * (F + 2) / (R + 2) XTAL to PLL Translation (PLLCFG) Base 0x400F.E000 Offset 0x064 Type RO, reset 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO - RO - RO - RO - RO - RO - 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO - RO - RO - RO - RO - RO - RO - RO - RO - reserved Type Reset OD Type Reset RO - F Bit/Field Name Type Reset 31:16 reserved RO 0x0 15:14 OD RO - R Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. PLL OD Value This field specifies the value supplied to the PLL’s OD input. Value Description 13:5 F RO - 0x0 Divide by 1 0x1 Divide by 2 0x2 Divide by 4 0x3 Reserved PLL F Value This field specifies the value supplied to the PLL’s F input. 4:0 R RO - PLL R Value This field specifies the value supplied to the PLL’s R input. July 14, 2014 173 Texas Instruments-Production Data System Control Register 10: Deep Sleep Clock Configuration (DSLPCLKCFG), offset 0x144 This register is used to automatically switch from the main oscillator to the internal oscillator when entering Deep-Sleep mode. The system clock source is the main oscillator by default. When this register is set, the internal oscillator is powered up and the main oscillator is powered down. When the Deep-Sleep exit event occurs, hardware brings the system clock back to the source and frequency it had at the onset of Deep-Sleep mode. Deep Sleep Clock Configuration (DSLPCLKCFG) Base 0x400F.E000 Offset 0x144 Type R/W, reset 0x0780.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:1 reserved RO 0x0 0 IOSC R/W 0 RO 0 IOSC R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. IOSC Clock Source When set, forces IOSC to be clock source during Deep-Sleep (overrides DSOSCSRC field if set) 174 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 11: Clock Verification Clear (CLKVCLR), offset 0x150 This register is provided as a means of clearing the clock verification circuits by software. Since the clock verification circuits force a known good clock to control the process, the controller is allowed the opportunity to solve the problem and clear the verification fault. This register clears all clock verification faults. To clear a clock verification fault, the VERCLR bit must be set and then cleared by software. This bit is not self-clearing. Clock Verification Clear (CLKVCLR) Base 0x400F.E000 Offset 0x150 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 VERCLR R/W 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 VERCLR R/W 0 Clock Verification Clear Clears clock verification faults. July 14, 2014 175 Texas Instruments-Production Data System Control Register 12: Allow Unregulated LDO to Reset the Part (LDOARST), offset 0x160 This register is provided as a means of allowing the LDO to reset the part if the voltage goes unregulated. Use this register to choose whether to automatically reset the part if the LDO goes unregulated, based on the design tolerance for LDO fluctuation. Allow Unregulated LDO to Reset the Part (LDOARST) Base 0x400F.E000 Offset 0x160 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 0 LDOARST RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 LDOARST R/W 0 LDO Reset When set, allows unregulated LDO output to reset the part. 176 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 13: Device Identification 1 (DID1), offset 0x004 This register identifies the device family, part number, temperature range, pin count, and package type. Each microcontroller is uniquely identified by the combined values of the CLASS field in the DID0 register and the PARTNO field in the DID1 register. Device Identification 1 (DID1) Base 0x400F.E000 Offset 0x004 Type RO, reset 31 30 29 28 27 26 RO 0 25 24 23 22 21 20 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO - RO - RO - VER Type Reset FAM TEMP RO 0 18 17 16 RO 1 RO 0 RO 1 RO 0 3 2 1 0 PARTNO reserved Type Reset 19 Bit/Field Name Type Reset 31:28 VER RO 0x0 RO - PKG ROHS RO - RO 1 QUAL RO - RO - Description DID1 Version This field defines the DID1 register format version. The version number is numeric. The value of the VER field is encoded as follows (all other encodings are reserved): Value Description 0x0 27:24 FAM RO 0x0 Initial DID1 register format definition, indicating a Stellaris LM3Snnn device. Family This field provides the family identification of the device within the Luminary Micro product portfolio. The value is encoded as follows (all other encodings are reserved): Value Description 0x0 23:16 PARTNO RO 0x2A Stellaris family of microcontollers, that is, all devices with external part numbers starting with LM3S. Part Number This field provides the part number of the device within the family. The value is encoded as follows (all other encodings are reserved): Value Description 0x2A LM3S600 15:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 177 Texas Instruments-Production Data System Control Bit/Field Name Type Reset 7:5 TEMP RO - Description Temperature Range This field specifies the temperature rating of the device. The value is encoded as follows (all other encodings are reserved): Value Description 4:3 PKG RO - 0x0 Commercial temperature range (0°C to 70°C) 0x1 Industrial temperature range (-40°C to 85°C) 0x2 Extended temperature range (-40°C to 105°C) Package Type This field specifies the package type. The value is encoded as follows (all other encodings are reserved): Value Description 2 ROHS RO 1 0x0 28-pin SOIC package 0x1 48-pin LQFP package 0x3 48-pin QFN package RoHS-Compliance This bit specifies whether the device is RoHS-compliant. A 1 indicates the part is RoHS-compliant. 1:0 QUAL RO - Qualification Status This field specifies the qualification status of the device. The value is encoded as follows (all other encodings are reserved): Value Description 0x0 Engineering Sample (unqualified) 0x1 Pilot Production (unqualified) 0x2 Fully Qualified 178 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 14: Device Capabilities 0 (DC0), offset 0x008 This register is predefined by the part and can be used to verify features. Device Capabilities 0 (DC0) Base 0x400F.E000 Offset 0x008 Type RO, reset 0x001F.000F 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 1 RO 1 RO 1 RO 1 RO 1 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 1 RO 1 SRAMSZ Type Reset FLASHSZ Type Reset RO 0 Bit/Field Name Type Reset Description 31:16 SRAMSZ RO 0x001F SRAM Size Indicates the size of the on-chip SRAM memory. Value Description 0x001F 8 KB of SRAM 15:0 FLASHSZ RO 0x000F Flash Size Indicates the size of the on-chip flash memory. Value Description 0x000F 32 KB of Flash July 14, 2014 179 Texas Instruments-Production Data System Control Register 15: Device Capabilities 1 (DC1), offset 0x010 This register provides a list of features available in the system. The Stellaris family uses this register format to indicate the availability of the following family features in the specific device: PWM, ADC, Watchdog timer, and debug capabilities. This register also indicates the maximum clock frequency and maximum ADC sample rate. The format of this register is consistent with the RCGC0, SCGC0, and DCGC0 clock control registers and the SRCR0 software reset control register. Device Capabilities 1 (DC1) Base 0x400F.E000 Offset 0x010 Type RO, reset 0x0000.309F 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 PLL WDT SWO SWD JTAG RO 1 RO 1 RO 1 RO 1 RO 1 reserved Type Reset MINSYSDIV Type Reset reserved RO 1 MPU Bit/Field Name Type Reset 31:16 reserved RO 0 15:12 MINSYSDIV RO 0x3 RO 1 reserved RO 0 RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. System Clock Divider Minimum 4-bit divider value for system clock. The reset value is hardware-dependent. See the RCC register for how to change the system clock divisor using the SYSDIV bit. Value Description 0x3 Specifies a 50-MHz CPU clock with a PLL divider of 4. 11:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 MPU RO 1 MPU Present When set, indicates that the Cortex-M3 Memory Protection Unit (MPU) module is present. See the "Cortex-M3 Peripherals" chapter in the Stellaris Data Sheet for details on the MPU. 6:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 PLL RO 1 PLL Present When set, indicates that the on-chip Phase Locked Loop (PLL) is present. 3 WDT RO 1 Watchdog Timer Present When set, indicates that a watchdog timer is present. 180 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 2 SWO RO 1 Description SWO Trace Port Present When set, indicates that the Serial Wire Output (SWO) trace port is present. 1 SWD RO 1 SWD Present When set, indicates that the Serial Wire Debugger (SWD) is present. 0 JTAG RO 1 JTAG Present When set, indicates that the JTAG debugger interface is present. July 14, 2014 181 Texas Instruments-Production Data System Control Register 16: Device Capabilities 2 (DC2), offset 0x014 This register provides a list of features available in the system. The Stellaris family uses this register format to indicate the availability of the following family features in the specific device: Analog Comparators, General-Purpose Timers, I2Cs, QEIs, SSIs, and UARTs. The format of this register is consistent with the RCGC1, SCGC1, and DCGC1 clock control registers and the SRCR1 software reset control register. Device Capabilities 2 (DC2) Base 0x400F.E000 Offset 0x014 Type RO, reset 0x0707.1013 31 30 RO 0 RO 0 15 14 29 28 27 26 25 24 RO 0 RO 0 RO 0 COMP2 COMP1 COMP0 RO 1 RO 1 13 12 11 10 9 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RO 0 I2C0 RO 0 RO 1 23 22 RO 1 RO 0 RO 0 8 7 RO 0 21 20 19 RO 0 RO 0 RO 0 6 5 4 3 RO 0 RO 0 reserved reserved RO 0 SSI0 RO 1 18 17 16 TIMER2 TIMER1 TIMER0 RO 1 RO 1 RO 1 2 1 0 UART1 UART0 RO 1 RO 1 reserved RO 0 RO 0 Bit/Field Name Type Reset Description 31:27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 COMP2 RO 1 Analog Comparator 2 Present When set, indicates that analog comparator 2 is present. 25 COMP1 RO 1 Analog Comparator 1 Present When set, indicates that analog comparator 1 is present. 24 COMP0 RO 1 Analog Comparator 0 Present When set, indicates that analog comparator 0 is present. 23:19 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 18 TIMER2 RO 1 Timer 2 Present When set, indicates that General-Purpose Timer module 2 is present. 17 TIMER1 RO 1 Timer 1 Present When set, indicates that General-Purpose Timer module 1 is present. 16 TIMER0 RO 1 Timer 0 Present When set, indicates that General-Purpose Timer module 0 is present. 15:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 I2C0 RO 1 I2C Module 0 Present When set, indicates that I2C module 0 is present. 182 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset Description 11:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 SSI0 RO 1 SSI0 Present When set, indicates that SSI module 0 is present. 3:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 UART1 RO 1 UART1 Present When set, indicates that UART module 1 is present. 0 UART0 RO 1 UART0 Present When set, indicates that UART module 0 is present. July 14, 2014 183 Texas Instruments-Production Data System Control Register 17: Device Capabilities 3 (DC3), offset 0x018 This register provides a list of features available in the system. The Stellaris family uses this register format to indicate the availability of the following family features in the specific device: Analog Comparator I/Os, CCP I/Os, ADC I/Os, and PWM I/Os. Device Capabilities 3 (DC3) Base 0x400F.E000 Offset 0x018 Type RO, reset 0xBF00.7FC0 Type Reset Type Reset 31 30 29 28 27 26 25 24 32KHZ reserved CCP5 CCP4 CCP3 CCP2 CCP1 CCP0 RO 1 RO 0 RO 1 RO 1 RO 1 RO 1 RO 1 15 14 13 12 11 10 9 reserved C2O RO 0 RO 1 C2PLUS C2MINUS RO 1 RO 1 C1O C1PLUS C1MINUS RO 1 RO 1 RO 1 Bit/Field Name Type Reset 31 32KHZ RO 1 23 22 21 20 RO 1 RO 0 RO 0 RO 0 RO 0 8 7 6 5 RO 0 C0O RO 1 19 18 17 16 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved C0PLUS C0MINUS RO 1 RO 1 reserved Description 32KHz Input Clock Available When set, indicates the 32KHz pin or an even CCP pin is present and can be used as a 32-KHz input clock. 30 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 29 CCP5 RO 1 CCP5 Pin Present When set, indicates that Capture/Compare/PWM pin 5 is present. 28 CCP4 RO 1 CCP4 Pin Present When set, indicates that Capture/Compare/PWM pin 4 is present. 27 CCP3 RO 1 CCP3 Pin Present When set, indicates that Capture/Compare/PWM pin 3 is present. 26 CCP2 RO 1 CCP2 Pin Present When set, indicates that Capture/Compare/PWM pin 2 is present. 25 CCP1 RO 1 CCP1 Pin Present When set, indicates that Capture/Compare/PWM pin 1 is present. 24 CCP0 RO 1 CCP0 Pin Present When set, indicates that Capture/Compare/PWM pin 0 is present. 23:15 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 14 C2O RO 1 C2o Pin Present When set, indicates that the analog comparator 2 output pin is present. 13 C2PLUS RO 1 C2+ Pin Present When set, indicates that the analog comparator 2 (+) input pin is present. 184 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 12 C2MINUS RO 1 Description C2- Pin Present When set, indicates that the analog comparator 2 (-) input pin is present. 11 C1O RO 1 C1o Pin Present When set, indicates that the analog comparator 1 output pin is present. 10 C1PLUS RO 1 C1+ Pin Present When set, indicates that the analog comparator 1 (+) input pin is present. 9 C1MINUS RO 1 C1- Pin Present When set, indicates that the analog comparator 1 (-) input pin is present. 8 C0O RO 1 C0o Pin Present When set, indicates that the analog comparator 0 output pin is present. 7 C0PLUS RO 1 C0+ Pin Present When set, indicates that the analog comparator 0 (+) input pin is present. 6 C0MINUS RO 1 C0- Pin Present When set, indicates that the analog comparator 0 (-) input pin is present. 5:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 185 Texas Instruments-Production Data System Control Register 18: Device Capabilities 4 (DC4), offset 0x01C This register provides a list of features available in the system. The Stellaris family uses this register format to indicate the availability of GPIOs in the specific device. The format of this register is consistent with the RCGC2, SCGC2, and DCGC2 clock control registers and the SRCR2 software reset control register. Device Capabilities 4 (DC4) Base 0x400F.E000 Offset 0x01C Type RO, reset 0x0000.001F 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 1 RO 1 RO 1 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 GPIOE RO 1 GPIO Port E Present When set, indicates that GPIO Port E is present. 3 GPIOD RO 1 GPIO Port D Present When set, indicates that GPIO Port D is present. 2 GPIOC RO 1 GPIO Port C Present When set, indicates that GPIO Port C is present. 1 GPIOB RO 1 GPIO Port B Present When set, indicates that GPIO Port B is present. 0 GPIOA RO 1 GPIO Port A Present When set, indicates that GPIO Port A is present. 186 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 19: Run Mode Clock Gating Control Register 0 (RCGC0), offset 0x100 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC0 is the clock configuration register for running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Run Mode Clock Gating Control Register 0 (RCGC0) Base 0x400F.E000 Offset 0x100 Type R/W, reset 0x00000040 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset WDT R/W 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 WDT R/W 0 WDT Clock Gating Control This bit controls the clock gating for the WDT module. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, a read or write to the unit generates a bus fault. 2:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 187 Texas Instruments-Production Data System Control Register 20: Sleep Mode Clock Gating Control Register 0 (SCGC0), offset 0x110 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC0 is the clock configuration register for running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Sleep Mode Clock Gating Control Register 0 (SCGC0) Base 0x400F.E000 Offset 0x110 Type R/W, reset 0x00000040 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WDT RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 WDT R/W 0 WDT Clock Gating Control This bit controls the clock gating for the WDT module. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, a read or write to the unit generates a bus fault. 2:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 188 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 21: Deep Sleep Mode Clock Gating Control Register 0 (DCGC0), offset 0x120 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC0 is the clock configuration register for running operation, SCGC0 for Sleep operation, and DCGC0 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Deep Sleep Mode Clock Gating Control Register 0 (DCGC0) Base 0x400F.E000 Offset 0x120 Type R/W, reset 0x00000040 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WDT RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 WDT R/W 0 WDT Clock Gating Control This bit controls the clock gating for the WDT module. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, a read or write to the unit generates a bus fault. 2:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 189 Texas Instruments-Production Data System Control Register 22: Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC1 is the clock configuration register for running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Run Mode Clock Gating Control Register 1 (RCGC1) Base 0x400F.E000 Offset 0x104 Type R/W, reset 0x00000000 31 30 RO 0 RO 0 15 14 29 28 27 26 25 24 RO 0 RO 0 RO 0 COMP2 COMP1 COMP0 R/W 0 R/W 0 13 12 11 10 9 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RO 0 I2C0 RO 0 R/W 0 23 22 R/W 0 RO 0 RO 0 8 7 RO 0 21 20 19 RO 0 RO 0 RO 0 6 5 4 3 RO 0 RO 0 reserved reserved RO 0 SSI0 R/W 0 18 17 16 TIMER2 TIMER1 TIMER0 R/W 0 R/W 0 R/W 0 2 1 0 UART1 UART0 R/W 0 R/W 0 reserved RO 0 RO 0 Bit/Field Name Type Reset Description 31:27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 COMP2 R/W 0 Analog Comparator 2 Clock Gating This bit controls the clock gating for analog comparator 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 25 COMP1 R/W 0 Analog Comparator 1 Clock Gating This bit controls the clock gating for analog comparator 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 24 COMP0 R/W 0 Analog Comparator 0 Clock Gating This bit controls the clock gating for analog comparator 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 23:19 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 190 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 18 TIMER2 R/W 0 Description Timer 2 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 17 TIMER1 R/W 0 Timer 1 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 16 TIMER0 R/W 0 Timer 0 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 15:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 I2C0 R/W 0 I2C0 Clock Gating Control This bit controls the clock gating for I2C module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 11:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 SSI0 R/W 0 SSI0 Clock Gating Control This bit controls the clock gating for SSI module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 UART1 R/W 0 UART1 Clock Gating Control This bit controls the clock gating for UART module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 0 UART0 R/W 0 UART0 Clock Gating Control This bit controls the clock gating for UART module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. July 14, 2014 191 Texas Instruments-Production Data System Control Register 23: Sleep Mode Clock Gating Control Register 1 (SCGC1), offset 0x114 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC1 is the clock configuration register for running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Sleep Mode Clock Gating Control Register 1 (SCGC1) Base 0x400F.E000 Offset 0x114 Type R/W, reset 0x00000000 31 30 29 28 27 reserved Type Reset RO 0 15 RO 0 RO 0 14 13 reserved Type Reset RO 0 RO 0 26 25 24 COMP2 COMP1 COMP0 R/W 0 RO 0 RO 0 RO 0 8 7 6 5 RO 0 RO 0 R/W 0 R/W 0 12 11 10 9 I2C0 RO 0 R/W 0 23 22 21 reserved RO 0 RO 0 RO 0 RO 0 20 19 reserved RO 0 RO 0 17 16 TIMER1 TIMER0 R/W 0 R/W 0 RO 0 RO 0 R/W 0 4 3 2 SSI0 RO 0 18 TIMER2 R/W 0 reserved RO 0 RO 0 1 0 UART1 UART0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 COMP2 R/W 0 Analog Comparator 2 Clock Gating This bit controls the clock gating for analog comparator 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 25 COMP1 R/W 0 Analog Comparator 1 Clock Gating This bit controls the clock gating for analog comparator 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 24 COMP0 R/W 0 Analog Comparator 0 Clock Gating This bit controls the clock gating for analog comparator 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 23:19 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 192 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 18 TIMER2 R/W 0 Description Timer 2 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 17 TIMER1 R/W 0 Timer 1 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 16 TIMER0 R/W 0 Timer 0 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 15:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 I2C0 R/W 0 I2C0 Clock Gating Control This bit controls the clock gating for I2C module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 11:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 SSI0 R/W 0 SSI0 Clock Gating Control This bit controls the clock gating for SSI module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 UART1 R/W 0 UART1 Clock Gating Control This bit controls the clock gating for UART module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 0 UART0 R/W 0 UART0 Clock Gating Control This bit controls the clock gating for UART module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. July 14, 2014 193 Texas Instruments-Production Data System Control Register 24: Deep Sleep Mode Clock Gating Control Register 1 (DCGC1), offset 0x124 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC1 is the clock configuration register for running operation, SCGC1 for Sleep operation, and DCGC1 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Deep Sleep Mode Clock Gating Control Register 1 (DCGC1) Base 0x400F.E000 Offset 0x124 Type R/W, reset 0x00000000 31 30 29 28 27 reserved Type Reset RO 0 15 RO 0 RO 0 14 13 reserved Type Reset RO 0 RO 0 26 25 24 COMP2 COMP1 COMP0 R/W 0 RO 0 RO 0 RO 0 8 7 6 5 RO 0 RO 0 R/W 0 R/W 0 12 11 10 9 I2C0 RO 0 R/W 0 23 22 21 reserved RO 0 RO 0 RO 0 RO 0 20 19 reserved RO 0 RO 0 17 16 TIMER1 TIMER0 R/W 0 R/W 0 RO 0 RO 0 R/W 0 4 3 2 SSI0 RO 0 18 TIMER2 R/W 0 reserved RO 0 RO 0 1 0 UART1 UART0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 COMP2 R/W 0 Analog Comparator 2 Clock Gating This bit controls the clock gating for analog comparator 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 25 COMP1 R/W 0 Analog Comparator 1 Clock Gating This bit controls the clock gating for analog comparator 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 24 COMP0 R/W 0 Analog Comparator 0 Clock Gating This bit controls the clock gating for analog comparator 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 23:19 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 194 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 18 TIMER2 R/W 0 Description Timer 2 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 2. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 17 TIMER1 R/W 0 Timer 1 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 16 TIMER0 R/W 0 Timer 0 Clock Gating Control This bit controls the clock gating for General-Purpose Timer module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 15:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 I2C0 R/W 0 I2C0 Clock Gating Control This bit controls the clock gating for I2C module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 11:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 SSI0 R/W 0 SSI0 Clock Gating Control This bit controls the clock gating for SSI module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 UART1 R/W 0 UART1 Clock Gating Control This bit controls the clock gating for UART module 1. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 0 UART0 R/W 0 UART0 Clock Gating Control This bit controls the clock gating for UART module 0. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. July 14, 2014 195 Texas Instruments-Production Data System Control Register 25: Run Mode Clock Gating Control Register 2 (RCGC2), offset 0x108 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC2 is the clock configuration register for running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Run Mode Clock Gating Control Register 2 (RCGC2) Base 0x400F.E000 Offset 0x108 Type R/W, reset 0x00000000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 GPIOE R/W 0 Port E Clock Gating Control This bit controls the clock gating for Port E. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3 GPIOD R/W 0 Port D Clock Gating Control This bit controls the clock gating for Port D. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 2 GPIOC R/W 0 Port C Clock Gating Control This bit controls the clock gating for Port C. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 1 GPIOB R/W 0 Port B Clock Gating Control This bit controls the clock gating for Port B. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 0 GPIOA R/W 0 Port A Clock Gating Control This bit controls the clock gating for Port A. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 196 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 26: Sleep Mode Clock Gating Control Register 2 (SCGC2), offset 0x118 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC2 is the clock configuration register for running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Sleep Mode Clock Gating Control Register 2 (SCGC2) Base 0x400F.E000 Offset 0x118 Type R/W, reset 0x00000000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 GPIOE R/W 0 Port E Clock Gating Control This bit controls the clock gating for Port E. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3 GPIOD R/W 0 Port D Clock Gating Control This bit controls the clock gating for Port D. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 2 GPIOC R/W 0 Port C Clock Gating Control This bit controls the clock gating for Port C. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 1 GPIOB R/W 0 Port B Clock Gating Control This bit controls the clock gating for Port B. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. July 14, 2014 197 Texas Instruments-Production Data System Control Bit/Field Name Type Reset 0 GPIOA R/W 0 Description Port A Clock Gating Control This bit controls the clock gating for Port A. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 198 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 27: Deep Sleep Mode Clock Gating Control Register 2 (DCGC2), offset 0x128 This register controls the clock gating logic. Each bit controls a clock enable for a given interface, function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault. The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are disabled. It is the responsibility of software to enable the ports necessary for the application. Note that these registers may contain more bits than there are interfaces, functions, or units to control. This is to assure reasonable code compatibility with other family and future parts. RCGC2 is the clock configuration register for running operation, SCGC2 for Sleep operation, and DCGC2 for Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register specifies that the system uses sleep modes. Deep Sleep Mode Clock Gating Control Register 2 (DCGC2) Base 0x400F.E000 Offset 0x128 Type R/W, reset 0x00000000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 GPIOE R/W 0 Port E Clock Gating Control This bit controls the clock gating for Port E. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 3 GPIOD R/W 0 Port D Clock Gating Control This bit controls the clock gating for Port D. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 2 GPIOC R/W 0 Port C Clock Gating Control This bit controls the clock gating for Port C. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 1 GPIOB R/W 0 Port B Clock Gating Control This bit controls the clock gating for Port B. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. July 14, 2014 199 Texas Instruments-Production Data System Control Bit/Field Name Type Reset 0 GPIOA R/W 0 Description Port A Clock Gating Control This bit controls the clock gating for Port A. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and disabled. If the unit is unclocked, reads or writes to the unit will generate a bus fault. 200 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 28: Software Reset Control 0 (SRCR0), offset 0x040 Writes to this register are masked by the bits in the Device Capabilities 1 (DC1) register. Software Reset Control 0 (SRCR0) Base 0x400F.E000 Offset 0x040 Type R/W, reset 0x00000000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset WDT R/W 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 WDT R/W 0 WDT Reset Control Reset control for Watchdog unit. 2:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 201 Texas Instruments-Production Data System Control Register 29: Software Reset Control 1 (SRCR1), offset 0x044 Writes to this register are masked by the bits in the Device Capabilities 2 (DC2) register. Software Reset Control 1 (SRCR1) Base 0x400F.E000 Offset 0x044 Type R/W, reset 0x00000000 31 30 RO 0 RO 0 15 14 29 28 27 26 25 24 RO 0 RO 0 RO 0 COMP2 COMP1 COMP0 R/W 0 R/W 0 13 12 11 10 9 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RO 0 I2C0 RO 0 R/W 0 23 22 R/W 0 RO 0 RO 0 8 7 RO 0 21 20 19 RO 0 RO 0 RO 0 6 5 4 3 RO 0 RO 0 reserved reserved RO 0 SSI0 R/W 0 18 17 16 TIMER2 TIMER1 TIMER0 R/W 0 R/W 0 R/W 0 2 1 0 UART1 UART0 R/W 0 R/W 0 reserved RO 0 RO 0 Bit/Field Name Type Reset Description 31:27 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 26 COMP2 R/W 0 Analog Comp 2 Reset Control Reset control for analog comparator 2. 25 COMP1 R/W 0 Analog Comp 1 Reset Control Reset control for analog comparator 1. 24 COMP0 R/W 0 Analog Comp 0 Reset Control Reset control for analog comparator 0. 23:19 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 18 TIMER2 R/W 0 Timer 2 Reset Control Reset control for General-Purpose Timer module 2. 17 TIMER1 R/W 0 Timer 1 Reset Control Reset control for General-Purpose Timer module 1. 16 TIMER0 R/W 0 Timer 0 Reset Control Reset control for General-Purpose Timer module 0. 15:13 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 12 I2C0 R/W 0 I2C0 Reset Control Reset control for I2C unit 0. 11:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 202 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 4 SSI0 R/W 0 Description SSI0 Reset Control Reset control for SSI unit 0. 3:2 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 UART1 R/W 0 UART1 Reset Control Reset control for UART unit 1. 0 UART0 R/W 0 UART0 Reset Control Reset control for UART unit 0. July 14, 2014 203 Texas Instruments-Production Data System Control Register 30: Software Reset Control 2 (SRCR2), offset 0x048 Writes to this register are masked by the bits in the Device Capabilities 4 (DC4) register. Software Reset Control 2 (SRCR2) Base 0x400F.E000 Offset 0x048 Type R/W, reset 0x00000000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 GPIOE R/W 0 Port E Reset Control Reset control for GPIO Port E. 3 GPIOD R/W 0 Port D Reset Control Reset control for GPIO Port D. 2 GPIOC R/W 0 Port C Reset Control Reset control for GPIO Port C. 1 GPIOB R/W 0 Port B Reset Control Reset control for GPIO Port B. 0 GPIOA R/W 0 Port A Reset Control Reset control for GPIO Port A. 204 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 6 Internal Memory The LM3S600 microcontroller comes with 8 KB of bit-banded SRAM and 32 KB of flash memory. The flash controller provides a user-friendly interface, making flash programming a simple task. Flash protection can be applied to the flash memory on a 2-KB block basis. 6.1 Block Diagram Figure 6-1 on page 205 illustrates the Flash functions. The dashed boxes in the figure indicate registers residing in the System Control module rather than the Flash Control module. Figure 6-1. Flash Block Diagram Flash Control Icode Bus Cortex-M3 System Bus Dcode Bus FMA FMD FMC FCRIS FCIM FCMISC Flash Array Flash Protection Bridge FMPRE FMPPE Flash Timing USECRL SRAM Array 6.2 Functional Description This section describes the functionality of the SRAM and Flash memories. 6.2.1 SRAM Memory ® The internal SRAM of the Stellaris devices is located at address 0x2000.0000 of the device memory map. To reduce the number of time consuming read-modify-write (RMW) operations, ARM has introduced bit-banding technology in the Cortex-M3 processor. With a bit-band-enabled processor, certain regions in the memory map (SRAM and peripheral space) can use address aliases to access individual bits in a single, atomic operation. The bit-band alias is calculated by using the formula: bit-band alias = bit-band base + (byte offset * 32) + (bit number * 4) For example, if bit 3 at address 0x2000.1000 is to be modified, the bit-band alias is calculated as: July 14, 2014 205 Texas Instruments-Production Data Internal Memory 0x2200.0000 + (0x1000 * 32) + (3 * 4) = 0x2202.000C With the alias address calculated, an instruction performing a read/write to address 0x2202.000C allows direct access to only bit 3 of the byte at address 0x2000.1000. For details about bit-banding, see “Bit-Banding” on page 63. 6.2.2 Flash Memory The flash is organized as a set of 1-KB blocks that can be individually erased. Erasing a block causes the entire contents of the block to be reset to all 1s. An individual 32-bit word can be programmed to change bits that are currently 1 to a 0. These blocks are paired into a set of 2-KB blocks that can be individually protected. The protection allows blocks to be marked as read-only or execute-only, providing different levels of code protection. Read-only blocks cannot be erased or programmed, protecting the contents of those blocks from being modified. Execute-only blocks cannot be erased or programmed, and can only be read by the controller instruction fetch mechanism, protecting the contents of those blocks from being read by either the controller or by a debugger. See also “Serial Flash Loader” on page 472 for a preprogrammed flash-resident utility used to download code to the flash memory of a device without the use of a debug interface. 6.2.2.1 Flash Memory Timing The timing for the flash is automatically handled by the flash controller. However, in order to do so, it must know the clock rate of the system in order to time its internal signals properly. The number of clock cycles per microsecond must be provided to the flash controller for it to accomplish this timing. It is software's responsibility to keep the flash controller updated with this information via the USec Reload (USECRL) register. On reset, the USECRL register is loaded with a value that configures the flash timing so that it works with the maximum clock rate of the part. If software changes the system operating frequency, the new operating frequency minus 1 (in MHz) must be loaded into USECRL before any flash modifications are attempted. For example, if the device is operating at a speed of 20 MHz, a value of 0x13 (20-1) must be written to the USECRL register. 6.2.2.2 Flash Memory Protection The user is provided two forms of flash protection per 2-KB flash blocks in two 32-bit wide registers.The protection policy for each form is controlled by individual bits (per policy per block) in the FMPPEn and FMPREn registers. ■ Flash Memory Protection Program Enable (FMPPEn): If set, the block may be programmed (written) or erased. If cleared, the block may not be changed. ■ Flash Memory Protection Read Enable (FMPREn): If a bit is set, the corresponding block may be executed or read by software or debuggers. If a bit is cleared, the corresponding block may only be executed, and contents of the memory block are prohibited from being read as data. The policies may be combined as shown in Table 6-1 on page 206. Table 6-1. Flash Protection Policy Combinations FMPPEn FMPREn 0 0 Protection Execute-only protection. The block may only be executed and may not be written or erased. This mode is used to protect code. 206 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 6-1. Flash Protection Policy Combinations (continued) FMPPEn FMPREn Protection 1 0 The block may be written, erased or executed, but not read. This combination is unlikely to be used. 0 1 Read-only protection. The block may be read or executed but may not be written or erased. This mode is used to lock the block from further modification while allowing any read or execute access. 1 1 No protection. The block may be written, erased, executed or read. A Flash memory access that attempts to read a read-protected block (FMPREn bit is set) is prohibited and generates a bus fault. A Flash memory access that attempts to program or erase a program-protected block (FMPPEn bit is set) is prohibited and can optionally generate an interrupt (by setting the AMASK bit in the Flash Controller Interrupt Mask (FCIM) register) to alert software developers of poorly behaving software during the development and debug phases. The factory settings for the FMPREn and FMPPEn registers are a value of 1 for all implemented banks. These settings create a policy of open access and programmability. The register bits may be changed by clearing the specific register bit. The changes are not permanent until the register is committed (saved), at which point the bit change is permanent. If a bit is changed from a 1 to a 0 and not committed, it may be restored by executing a power-on reset sequence. The changes are committed using the Flash Memory Control (FMC) register. 6.2.2.3 Execute-Only Protection Execute-only protection prevents both modification and visibility to a protected flash block. This mode is intended to be used in situations where a device requires debug capability, yet portions of the application space must be protected from external access. An example of this is a company who wishes to sell Stellaris devices with their proprietary software pre-programmed, yet allow the end user to add custom code to an unprotected region of the flash (such as a motor control module with a customizable motor configuration section in flash). Literal data introduces a complication to the protection mechanism. When C code is compiled and linked, literal data (constants, and so on) is typically placed in the text section, between functions, by the compiler. The literal data is accessed at run time through the use of the LDR instruction, which loads the data from memory using a PC-relative memory address. The execution of the LDR instruction generates a read transaction across the Cortex-M3's DCode bus, which is subject to the execute-only protection mechanism. If the accessed block is marked as execute only, the transaction is blocked, and the processor is prevented from loading the constant data and, therefore, inhibiting correct execution. Therefore, using execute-only protection requires that literal data be handled differently. There are three ways to address this: 1. Use a compiler that allows literal data to be collected into a separate section that is put into one or more read-enabled flash blocks. Note that the LDR instruction may use a PC-relative address–-in which case the literal pool cannot be located outside the span of the offset–-or the software may reserve a register to point to the base address of the literal pool and the LDR offset is relative to the beginning of the pool. 2. Use a compiler that generates literal data from arithmetic instruction immediate data and subsequent computation. 3. Use method 1 or 2, but in assembly language, if the compiler does not support either method. July 14, 2014 207 Texas Instruments-Production Data Internal Memory 6.2.2.4 Read-Only Protection Read-only protection prevents the contents of the flash block from being re-programmed, while still allowing the content to be read by processor or the debug interface. Note that if a FMPREn bit is cleared, all read accesses to the Flash memory block are disallowed, including any data accesses. Care must be taken not to store required data in a Flash memory block that has the associated FMPREn bit cleared. The read-only mode does not prevent read access to the stored program, but it does provide protection against accidental (or malicious) erasure or programming. Read-only is especially useful for utilities like the boot loader when the debug interface is permanently disabled. In such combinations, the boot loader, which provides access control to the Flash memory, is protected from being erased or modified. 6.2.2.5 Permanently Disabling Debug For extremely sensitive applications, the debug interface to the processor and peripherals can be permanently disabled, blocking all accesses to the device through the JTAG or SWD interfaces. With the debug interface disabled, it is still possible to perform standard IEEE instructions (such as boundary scan operations), but access to the processor and peripherals is blocked. The two most-significant bits of the FMPRE register are the DBG bits, and control whether or not the debug interface is turned on or off. Since the DBG bits are part of the FMPRE register, the user loses the capability to mark the upper two flash blocks in a 64 KB flash device as execute-only. The debug interface should not be permanently disabled without providing some mechanism–-such as the boot loader–-to provide customer-installable updates or bug fixes. Disabling the debug interface is permanent and cannot be reversed. 6.2.2.6 Interrupts The Flash memory controller can generate interrupts when the following conditions are observed: ■ Programming Interrupt - signals when a program or erase action is complete. ■ Access Interrupt - signals when a program or erase action has been attempted on a 2-kB block of memory that is protected by its corresponding FMPPEn bit. The interrupt events that can trigger a controller-level interrupt are defined in the Flash Controller Masked Interrupt Status (FCMIS) register (see page 217) by setting the corresponding MASK bits. If interrupts are not used, the raw interrupt status is always visible via the Flash Controller Raw Interrupt Status (FCRIS) register (see page 216). Interrupts are always cleared (for both the FCMIS and FCRIS registers) by writing a 1 to the corresponding bit in the Flash Controller Masked Interrupt Status and Clear (FCMISC) register (see page 218). 6.2.2.7 Flash Memory Protection by Disabling Debug Access Flash memory may also be protected by permanently disabling access to the Debug Access Port (DAP) through the JTAG and SWD interfaces. Access is disabled by clearing the DBG field of the FMPRE register. If the DBG field in the Flash Memory Protection Read Enable (FMPRE) register is programmed to 0x2, access to the DAP is enabled through the JTAG and SWD interfaces. If clear, access to the DAP is disabled. The DBG field programming becomes permanent and irreversible after a commit sequence is performed. 208 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller In the initial state provided from the factory, access is enabled in order to facilitate code development and debug. Access to the DAP may be disabled at the end of the manufacturing flow, once all tests have passed and software has been loaded. This change does not take effect until the next power-up of the device. Note that it is recommended that disabling access to the DAP be combined with a mechanism for providing end-user installable updates (if necessary) such as the Stellaris boot loader. Important: Once the DBG field is cleared and committed, this field can never be restored to the factory-programmed value—which means the JTAG/SWD interface to the debug module can never be re-enabled. This sequence does NOT disable the JTAG controller, it only disables the access of the DAP through the JTAG or SWD interfaces. The JTAG interface remains functional and access to the Test Access Port remains enabled, allowing the user to execute the IEEE JTAG-defined instructions (for example, to perform boundary scan operations). When using the FMPRE bits to protect Flash memory from being read as data (to mark sets of 2-KB blocks of Flash memory as execute-only), these one-time-programmable bits should be written at the same time that the debug disable bits are programmed. Mechanisms to execute the one-time code sequence to disable all debug access include: ■ Selecting the debug disable option in the Stellaris boot loader ■ Loading the debug disable sequence into SRAM and running it once from SRAM after programming the final end application code into Flash memory 6.3 Flash Memory Initialization and Configuration This section shows examples for using the flash controller to perform various operations on the contents of the flash memory. 6.3.1 Changing Flash Protection Bits As discussed in “Flash Memory Protection” on page 206, changes to the protection bits must be committed before they take effect. The sequence below is used change and commit a block protection bit in the FMPRE or FMPPE registers. The sequence to change and commit a bit in software is as follows: 1. The Flash Memory Protection Read Enable (FMPRE) and Flash Memory Protection Program Enable (FMPPE) registers are written, changing the intended bit(s). The action of these changes can be tested by software while in this state. 2. The Flash Memory Address (FMA) register (see page 212) bit 0 is set to 1 if the FMPPE register is to be committed; otherwise, a 0 commits the FMPRE register. 3. The Flash Memory Control (FMC) register (see page 214) is written with the COMT bit set. This initiates a write sequence and commits the changes. There is a special sequence to change and commit the DBG bits in the Flash Memory Protection Read Enable (FMPRE) register. This sequence also sets and commits any changes from 1 to 0 in the block protection bits (for execute-only) in the FMPRE register. 1. The Flash Memory Protection Read Enable (FMPRE) register is written, changing the intended bit(s). The action of these changes can be tested by software while in this state. 2. The Flash Memory Address (FMA) register (see page 212) is written with a value of 0x900. July 14, 2014 209 Texas Instruments-Production Data Internal Memory 3. The Flash Memory Control (FMC) register (see page 214) is written with the COMT bit set. This initiates a write sequence and commits the changes. Below is an example code sequence to permanently disable the JTAG and SWD interface to the debug module using DriverLib: #include "hw_types.h" #include "hw_flash.h" void permanently_disable_jtag_swd(void) { // // Clear the DBG field of the FMPRE register. Note that the value // used in this instance does not affect the state of the BlockN // bits, but were the value different, all bits in the FMPRE are // affected by this function! // HWREG(FLASH_FMPRE) &= 0x3fffffff; // // The following sequence activates the one-time // programming of the FMPRE register. // HWREG(FLASH_FMA) = 0x900; HWREG(FLASH_FMC) = (FLASH_FMC_WRKEY | FLASH_FMC_COMT); // // Wait until the operation is complete. // while (HWREG(FLASH_FMC) & FLASH_FMC_COMT) { } } 6.3.2 Flash Programming The Stellaris devices provide a user-friendly interface for flash programming. All erase/program operations are handled via three registers: FMA, FMD, and FMC. During a Flash memory operation (write, page erase, or mass erase) access to the Flash memory is inhibited. As a result, instruction and literal fetches are held off until the Flash memory operation is complete. If instruction execution is required during a Flash memory operation, the code that is executing must be placed in SRAM and executed from there while the flash operation is in progress. 6.3.2.1 To program a 32-bit word 1. Write source data to the FMD register. 2. Write the target address to the FMA register. 3. Write the flash write key and the WRITE bit (a value of 0xA442.0001) to the FMC register. 4. Poll the FMC register until the WRITE bit is cleared. 6.3.2.2 To perform an erase of a 1-KB page 1. Write the page address to the FMA register. 210 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 2. Write the flash write key and the ERASE bit (a value of 0xA442.0002) to the FMC register. 3. Poll the FMC register until the ERASE bit is cleared. 6.3.2.3 To perform a mass erase of the flash 1. Write the flash write key and the MERASE bit (a value of 0xA442.0004) to the FMC register. 2. Poll the FMC register until the MERASE bit is cleared. 6.4 Register Map Table 6-2 on page 211 lists the Flash memory and control registers. The offset listed is a hexadecimal increment to the register's address. The FMA, FMD, FMC, FCRIS, FCIM, and FCMISC register offsets are relative to the Flash memory control base address of 0x400F.D000. The Flash memory protection register offsets are relative to the System Control base address of 0x400F.E000. Table 6-2. Flash Register Map Offset Name Type Reset Description See page Flash Memory Control Registers (Flash Control Offset) 0x000 FMA R/W 0x0000.0000 Flash Memory Address 212 0x004 FMD R/W 0x0000.0000 Flash Memory Data 213 0x008 FMC R/W 0x0000.0000 Flash Memory Control 214 0x00C FCRIS RO 0x0000.0000 Flash Controller Raw Interrupt Status 216 0x010 FCIM R/W 0x0000.0000 Flash Controller Interrupt Mask 217 0x014 FCMISC R/W1C 0x0000.0000 Flash Controller Masked Interrupt Status and Clear 218 Flash Memory Protection Registers (System Control Offset) 0x130 FMPRE R/W 0x8000.FFFF Flash Memory Protection Read Enable 221 0x134 FMPPE R/W 0x0000.FFFF Flash Memory Protection Program Enable 222 0x140 USECRL R/W 0x31 USec Reload 220 6.5 Flash Register Descriptions (Flash Control Offset) This section lists and describes the Flash Memory registers, in numerical order by address offset. Registers in this section are relative to the Flash control base address of 0x400F.D000. July 14, 2014 211 Texas Instruments-Production Data Internal Memory Register 1: Flash Memory Address (FMA), offset 0x000 During a write operation, this register contains a 4-byte-aligned address and specifies where the data is written. During erase operations, this register contains a 1 KB-aligned address and specifies which page is erased. Note that the alignment requirements must be met by software or the results of the operation are unpredictable. Flash Memory Address (FMA) Base 0x400F.D000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 OFFSET R/W 0 Bit/Field Name Type Reset Description 31:15 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 14:0 OFFSET R/W 0x0 Address Offset Address offset in flash where operation is performed. 212 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 2: Flash Memory Data (FMD), offset 0x004 This register contains the data to be written during the programming cycle or read during the read cycle. Note that the contents of this register are undefined for a read access of an execute-only block. This register is not used during the erase cycles. Flash Memory Data (FMD) Base 0x400F.D000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 DATA Type Reset DATA Type Reset Bit/Field Name Type Reset Description 31:0 DATA R/W 0x0 Data Value Data value for write operation. July 14, 2014 213 Texas Instruments-Production Data Internal Memory Register 3: Flash Memory Control (FMC), offset 0x008 When this register is written, the flash controller initiates the appropriate access cycle for the location specified by the Flash Memory Address (FMA) register (see page 212). If the access is a write access, the data contained in the Flash Memory Data (FMD) register (see page 213) is written. This is the final register written and initiates the memory operation. There are four control bits in the lower byte of this register that, when set, initiate the memory operation. The most used of these register bits are the ERASE and WRITE bits. It is a programming error to write multiple control bits and the results of such an operation are unpredictable. Flash Memory Control (FMC) Base 0x400F.D000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 COMT MERASE ERASE WRITE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 WRKEY Type Reset reserved Type Reset Bit/Field Name Type Reset 31:16 WRKEY WO 0x0 Description Flash Write Key This field contains a write key, which is used to minimize the incidence of accidental flash writes. The value 0xA442 must be written into this field for a write to occur. Writes to the FMC register without this WRKEY value are ignored. A read of this field returns the value 0. 15:4 reserved RO 0x0 3 COMT R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Commit Register Value Commit (write) of register value to nonvolatile storage. A write of 0 has no effect on the state of this bit. If read, the state of the previous commit access is provided. If the previous commit access is complete, a 0 is returned; otherwise, if the commit access is not complete, a 1 is returned. This can take up to 50 μs. 2 MERASE R/W 0 Mass Erase Flash Memory If this bit is set, the flash main memory of the device is all erased. A write of 0 has no effect on the state of this bit. If read, the state of the previous mass erase access is provided. If the previous mass erase access is complete, a 0 is returned; otherwise, if the previous mass erase access is not complete, a 1 is returned. This can take up to 250 ms. 214 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 1 ERASE R/W 0 Description Erase a Page of Flash Memory If this bit is set, the page of flash main memory as specified by the contents of FMA is erased. A write of 0 has no effect on the state of this bit. If read, the state of the previous erase access is provided. If the previous erase access is complete, a 0 is returned; otherwise, if the previous erase access is not complete, a 1 is returned. This can take up to 25 ms. 0 WRITE R/W 0 Write a Word into Flash Memory If this bit is set, the data stored in FMD is written into the location as specified by the contents of FMA. A write of 0 has no effect on the state of this bit. If read, the state of the previous write update is provided. If the previous write access is complete, a 0 is returned; otherwise, if the write access is not complete, a 1 is returned. This can take up to 50 µs. July 14, 2014 215 Texas Instruments-Production Data Internal Memory Register 4: Flash Controller Raw Interrupt Status (FCRIS), offset 0x00C This register indicates that the flash controller has an interrupt condition. An interrupt is only signaled if the corresponding FCIM register bit is set. Flash Controller Raw Interrupt Status (FCRIS) Base 0x400F.D000 Offset 0x00C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 PRIS ARIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0 1 PRIS RO 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Programming Raw Interrupt Status This bit provides status on programming cycles which are write or erase actions generated through the FMC register bits (see page 214). Value Description 1 The programming cycle has completed. 0 The programming cycle has not completed. This status is sent to the interrupt controller when the PMASK bit in the FCIM register is set. This bit is cleared by writing a 1 to the PMISC bit in the FCMISC register. 0 ARIS RO 0 Access Raw Interrupt Status Value Description 1 A program or erase action was attempted on a block of Flash memory that contradicts the protection policy for that block as set in the FMPPEn registers. 0 No access has tried to improperly program or erase the Flash memory. This status is sent to the interrupt controller when the AMASK bit in the FCIM register is set. This bit is cleared by writing a 1 to the AMISC bit in the FCMISC register. 216 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: Flash Controller Interrupt Mask (FCIM), offset 0x010 This register controls whether the flash controller generates interrupts to the controller. Flash Controller Interrupt Mask (FCIM) Base 0x400F.D000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 PMASK AMASK RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset 31:2 reserved RO 0x0 1 PMASK R/W 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Programming Interrupt Mask This bit controls the reporting of the programming raw interrupt status to the interrupt controller. Value Description 0 AMASK R/W 0 1 An interrupt is sent to the interrupt controller when the PRIS bit is set. 0 The PRIS interrupt is suppressed and not sent to the interrupt controller. Access Interrupt Mask This bit controls the reporting of the access raw interrupt status to the interrupt controller. Value Description 1 An interrupt is sent to the interrupt controller when the ARIS bit is set. 0 The ARIS interrupt is suppressed and not sent to the interrupt controller. July 14, 2014 217 Texas Instruments-Production Data Internal Memory Register 6: Flash Controller Masked Interrupt Status and Clear (FCMISC), offset 0x014 This register provides two functions. First, it reports the cause of an interrupt by indicating which interrupt source or sources are signalling the interrupt. Second, it serves as the method to clear the interrupt reporting. Flash Controller Masked Interrupt Status and Clear (FCMISC) Base 0x400F.D000 Offset 0x014 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset 31:2 reserved RO 0x0 1 PMISC R/W1C 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 PMISC AMISC R/W1C 0 R/W1C 0 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Programming Masked Interrupt Status and Clear Value Description 1 When read, a 1 indicates that an unmasked interrupt was signaled because a programming cycle completed. Writing a 1 to this bit clears PMISC and also the PRIS bit in the FCRIS register (see page 216). 0 When read, a 0 indicates that a programming cycle complete interrupt has not occurred. A write of 0 has no effect on the state of this bit. 0 AMISC R/W1C 0 Access Masked Interrupt Status and Clear Value Description 1 When read, a 1 indicates that an unmasked interrupt was signaled because a program or erase action was attempted on a block of Flash memory that contradicts the protection policy for that block as set in the FMPPEn registers. Writing a 1 to this bit clears AMISC and also the ARIS bit in the FCRIS register (see page 216). 0 When read, a 0 indicates that no improper accesses have occurred. A write of 0 has no effect on the state of this bit. 218 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 6.6 Flash Register Descriptions (System Control Offset) The remainder of this section lists and describes the Flash Memory registers, in numerical order by address offset. Registers in this section are relative to the System Control base address of 0x400F.E000. July 14, 2014 219 Texas Instruments-Production Data Internal Memory Register 7: USec Reload (USECRL), offset 0x140 Note: Offset is relative to System Control base address of 0x400F.E000 This register is provided as a means of creating a 1-μs tick divider reload value for the flash controller. The internal flash has specific minimum and maximum requirements on the length of time the high voltage write pulse can be applied. It is required that this register contain the operating frequency (in MHz -1) whenever the flash is being erased or programmed. The user is required to change this value if the clocking conditions are changed for a flash erase/program operation. USec Reload (USECRL) Base 0x400F.E000 Offset 0x140 Type R/W, reset 0x31 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 USEC RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 1 R/W 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 USEC R/W 0x31 Microsecond Reload Value MHz -1 of the controller clock when the flash is being erased or programmed. If the maximum system frequency is being used, USEC should be set to 0x31 (50 MHz) whenever the flash is being erased or programmed. 220 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: Flash Memory Protection Read Enable (FMPRE), offset 0x130 Note: Offset is relative to System Control base address of 0x400FE000. This register stores the read-only protection bits for each 2-KB flash block (see the FMPPE registers for the execute-only protection bits). This register is loaded during the power-on reset sequence. The factory settingsare a value of 1 for all implemented banks. This implements a policy of open access and programmability. The register bits may be changed by writing the specific register bit. However, this register is R/W0; the user can only change the protection bit from a 1 to a 0 (and may NOT change a 0 to a 1). The changes are not permanent until the register is committed (saved), at which point the bit change is permanent. If a bit is changed from a 1 to a 0 and not committed, it may be restored by executing a power-on reset sequence. For additional information, see the “Flash Memory Protection” section. Flash Memory Protection Read Enable (FMPRE) Base 0x400F.E000 Offset 0x130 Type R/W, reset 0x8000.FFFF 31 30 29 28 27 26 25 24 DBG Type Reset 23 22 21 20 19 18 17 16 READ_ENABLE R/W 1 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 8 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 READ_ENABLE Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type Reset 31:30 DBG R/W 0x2 R/W 1 R/W 1 Description User Controlled Debug Enable Each bit position maps 2 Kbytes of Flash to be read-enabled. Value Description 0x2 29:0 READ_ENABLE R/W Debug access allowed 0x0000FFFF Flash Read Enable Each bit position maps 2 Kbytes of Flash to be read-enabled. Value Description 0x0000FFFF Enables 32 KB of flash. July 14, 2014 221 Texas Instruments-Production Data Internal Memory Register 9: Flash Memory Protection Program Enable (FMPPE), offset 0x134 Note: Offset is relative to System Control base address of 0x400FE000. This register stores the execute-only protection bits for each 2-KB flash block (see the FMPRE registers for the read-only protection bits). This register is loaded during the power-on reset sequence. The factory settings are a value of 1 for all implemented banks. This implements a policy of open access and programmability. The register bits may be changed by writing the specific register bit. However, this register is R/W0; the user can only change the protection bit from a 1 to a 0 (and may NOT change a 0 to a 1). The changes are not permanent until the register is committed (saved), at which point the bit change is permanent. If a bit is changed from a 1 to a 0 and not committed, it may be restored by executing a power-on reset sequence. For additional information, see the “Flash Memory Protection” section. Flash Memory Protection Program Enable (FMPPE) Base 0x400F.E000 Offset 0x134 Type R/W, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 PROG_ENABLE Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 8 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 PROG_ENABLE Type Reset R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type 31:0 PROG_ENABLE R/W R/W 1 Reset R/W 1 R/W 1 Description 0x0000FFFF Flash Programming Enable Each bit position maps 2 Kbytes of Flash to be write-enabled. Value Description 0x0000FFFF Enables 32 KB of flash. 222 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 7 General-Purpose Input/Outputs (GPIOs) The GPIO module is composed of five physical GPIO blocks, each corresponding to an individual GPIO port (Port A, Port B, Port C, Port D, Port E). The GPIO module supports 8-36 programmable input/output pins, depending on the peripherals being used. The GPIO module has the following features: ■ 8-36 GPIOs, depending on configuration ■ 5-V-tolerant in input configuration ■ Fast toggle capable of a change every two clock cycles ■ Programmable control for GPIO interrupts – Interrupt generation masking – Edge-triggered on rising, falling, or both – Level-sensitive on High or Low values ■ Bit masking in both read and write operations through address lines ■ Pins configured as digital inputs are Schmitt-triggered. ■ Programmable control for GPIO pad configuration – Weak pull-up or pull-down resistors – 2-mA, 4-mA, and 8-mA pad drive for digital communication – Slew rate control for the 8-mA drive – Open drain enables – Digital input enables 7.1 Signal Description GPIO signals have alternate hardware functions. Table 7-3 on page 225 lists the GPIO pins and their digital alternate functions. Other analog signals are 5-V tolerant and are connected directly to their circuitry (C0-, C0+, C1-, C1+, C2-, C2+). These signals are configured by clearing the DEN bit in the GPIO Digital Enable (GPIODEN) register. The digital alternate hardware functions are enabled by setting the appropriate bit in the GPIO Alternate Function Select (GPIOAFSEL) and GPIODEN registers and configuring the PMCx bit field in the GPIO Port Control (GPIOPCTL) register to the numeric enoding shown in the table below. Note that each pin must be programmed individually; no type of grouping is implied by the columns in the table. Important: All GPIO pins are configured as GPIOs and tri-stated by default (GPIOAFSEL=0, GPIODEN=0, GPIOPDR=0, GPIOPUR=0, and GPIOPCTL=0, with the exception of the four JTAG/SWD pins (shown in the table below). A Power-On-Reset (POR) or asserting RST puts the pins back to their default state. July 14, 2014 223 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Table 7-1. GPIO Pins With Non-Zero Reset Values GPIO Pins Default State PA[1:0] UART0 GPIOAFSEL GPIODEN GPIOPDR GPIOPUR 1 1 0 0 GPIOPCTL 0x1 PA[5:2] SSI0 1 1 0 0 0x1 PB[3:2] I2C0 1 1 0 0 0x1 PC[3:0] JTAG/SWD 1 1 0 1 0x3 Table 7-2. GPIO Pins and Alternate Functions (48QFP) IO Pin Number Multiplexed Function PA0 17 U0Rx PA1 18 U0Tx PA2 19 SSIClk Multiplexed Function PA3 20 SSIFss PA4 21 SSIRx PA5 22 SSITx PB0 29 PB1 30 PB2 33 I2CSCL PB3 34 I2CSDA PB4 44 C0- PB5 43 C1- PB6 42 C0+ PB7 41 TRST PC0 40 TCK SWCLK PC1 39 TMS SWDIO PC2 38 TDI PC3 37 TDO SWO PC4 14 PC5 13 C1+ C1o PC6 12 C2+ C2o PC7 11 C2- PD0 25 PD1 26 PD2 27 U1Rx PD3 28 U1Tx PD4 45 CCP0 PD5 46 CCP2 PD6 47 PD7 48 PE0 35 PE1 36 PE2 4 C0o CCP4 224 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 7-2. GPIO Pins and Alternate Functions (48QFP) (continued) IO Pin Number Multiplexed Function PE3 3 CCP1 PE4 2 CCP3 PE5 1 CCP5 Multiplexed Function Table 7-3. GPIO Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type PA0 17 I/O TTL Description GPIO port A bit 0. PA1 18 I/O TTL GPIO port A bit 1. PA2 19 I/O TTL GPIO port A bit 2. PA3 20 I/O TTL GPIO port A bit 3. PA4 21 I/O TTL GPIO port A bit 4. PA5 22 I/O TTL GPIO port A bit 5. PB0 29 I/O TTL GPIO port B bit 0. PB1 30 I/O TTL GPIO port B bit 1. PB2 33 I/O TTL GPIO port B bit 2. PB3 34 I/O TTL GPIO port B bit 3. PB4 44 I/O TTL GPIO port B bit 4. PB5 43 I/O TTL GPIO port B bit 5. PB6 42 I/O TTL GPIO port B bit 6. PB7 41 I/O TTL GPIO port B bit 7. PC0 40 I/O TTL GPIO port C bit 0. PC1 39 I/O TTL GPIO port C bit 1. PC2 38 I/O TTL GPIO port C bit 2. PC3 37 I/O TTL GPIO port C bit 3. PC4 14 I/O TTL GPIO port C bit 4. PC5 13 I/O TTL GPIO port C bit 5. PC6 12 I/O TTL GPIO port C bit 6. PC7 11 I/O TTL GPIO port C bit 7. PD0 25 I/O TTL GPIO port D bit 0. PD1 26 I/O TTL GPIO port D bit 1. PD2 27 I/O TTL GPIO port D bit 2. PD3 28 I/O TTL GPIO port D bit 3. PD4 45 I/O TTL GPIO port D bit 4. PD5 46 I/O TTL GPIO port D bit 5. PD6 47 I/O TTL GPIO port D bit 6. PD7 48 I/O TTL GPIO port D bit 7. PE0 35 I/O TTL GPIO port E bit 0. PE1 36 I/O TTL GPIO port E bit 1. PE2 4 I/O TTL GPIO port E bit 2. PE3 3 I/O TTL GPIO port E bit 3. PE4 2 I/O TTL GPIO port E bit 4. July 14, 2014 225 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Table 7-3. GPIO Signals (48QFP) (continued) a Pin Name Pin Number Pin Type Buffer Type PE5 1 I/O TTL Description GPIO port E bit 5. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 7.2 Functional Description Important: All GPIO pins are inputs by default (GPIODIR=0 and GPIOAFSEL=0), with the exception of the five JTAG pins (PB7 and PC[3:0]). The JTAG pins default to their JTAG functionality (GPIOAFSEL=1). A Power-On-Reset (POR) or asserting an external reset (RST) puts both groups of pins back to their default state. While debugging systems where PB7 is being used as a GPIO, care must be taken to ensure that a Low value is not applied to the pin when the part is reset. Because PB7 reverts to the TRST function after reset, a Low value on the pin causes the JTAG controller to be reset, resulting in a loss of JTAG communication. Each GPIO port is a separate hardware instantiation of the same physical block (see Figure 7-1 on page 226). The LM3S600 microcontroller contains five ports and thus five of these physical GPIO blocks. Figure 7-1. GPIO Port Block Diagram Mode Control GPIOAFSEL DEMUX Alternate Input Alternate Output Pad Input Alternate Output Enable Pad Output MUX Pad Output Enable Digital I/O Pad Package I/O Pin GPIO Output GPIODATA GPIODIR Interrupt MUX GPIO Input Data Control GPIO Output Enable Interrupt Control Pad Control GPIOIS GPIOIBE GPIOIEV GPIOIM GPIORIS GPIOMIS GPIOICR GPIODR2R GPIODR4R GPIODR8R GPIOSLR GPIOPUR GPIOPDR GPIOODR GPIODEN Identification Registers GPIOPeriphID0 GPIOPeriphID1 GPIOPeriphID2 GPIOPeriphID3 GPIOPeriphID4 GPIOPeriphID5 GPIOPeriphID6 GPIOPeriphID7 GPIOPCellID0 GPIOPCellID1 GPIOPCellID2 GPIOPCellID3 226 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 7.2.1 Data Control The data control registers allow software to configure the operational modes of the GPIOs. The data direction register configures the GPIO as an input or an output while the data register either captures incoming data or drives it out to the pads. 7.2.1.1 Data Direction Operation The GPIO Direction (GPIODIR) register (see page 233) is used to configure each individual pin as an input or output. When the data direction bit is set to 0, the GPIO is configured as an input and the corresponding data register bit will capture and store the value on the GPIO port. When the data direction bit is set to 1, the GPIO is configured as an output and the corresponding data register bit will be driven out on the GPIO port. 7.2.1.2 Data Register Operation To aid in the efficiency of software, the GPIO ports allow for the modification of individual bits in the GPIO Data (GPIODATA) register (see page 232) by using bits [9:2] of the address bus as a mask. This allows software drivers to modify individual GPIO pins in a single instruction, without affecting the state of the other pins. This is in contrast to the "typical" method of doing a read-modify-write operation to set or clear an individual GPIO pin. To accommodate this feature, the GPIODATA register covers 256 locations in the memory map. During a write, if the address bit associated with that data bit is set to 1, the value of the GPIODATA register is altered. If it is cleared to 0, it is left unchanged. For example, writing a value of 0xEB to the address GPIODATA + 0x098 would yield as shown in Figure 7-2 on page 227, where u is data unchanged by the write. Figure 7-2. GPIODATA Write Example ADDR[9:2] 0x098 9 8 7 6 5 4 3 2 1 0 0 0 1 0 0 1 1 0 0 0 0xEB 1 1 1 0 1 0 1 1 GPIODATA u u 1 u u 0 1 u 7 6 5 4 3 2 1 0 During a read, if the address bit associated with the data bit is set to 1, the value is read. If the address bit associated with the data bit is set to 0, it is read as a zero, regardless of its actual value. For example, reading address GPIODATA + 0x0C4 yields as shown in Figure 7-3 on page 227. Figure 7-3. GPIODATA Read Example ADDR[9:2] 0x0C4 9 8 7 6 5 4 3 2 1 0 0 0 1 1 0 0 0 1 0 0 GPIODATA 1 0 1 1 1 1 1 0 Returned Value 0 0 1 1 0 0 0 0 7 6 5 4 3 2 1 0 July 14, 2014 227 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) 7.2.2 Interrupt Control The interrupt capabilities of each GPIO port are controlled by a set of seven registers. With these registers, it is possible to select the source of the interrupt, its polarity, and the edge properties. When one or more GPIO inputs cause an interrupt, a single interrupt output is sent to the interrupt controller for the entire GPIO port. For edge-triggered interrupts, software must clear the interrupt to enable any further interrupts. For a level-sensitive interrupt, it is assumed that the external source holds the level constant for the interrupt to be recognized by the controller. Three registers are required to define the edge or sense that causes interrupts: ■ GPIO Interrupt Sense (GPIOIS) register (see page 234) ■ GPIO Interrupt Both Edges (GPIOIBE) register (see page 235) ■ GPIO Interrupt Event (GPIOIEV) register (see page 236) Interrupts are enabled/disabled via the GPIO Interrupt Mask (GPIOIM) register (see page 237). When an interrupt condition occurs, the state of the interrupt signal can be viewed in two locations: the GPIO Raw Interrupt Status (GPIORIS) and GPIO Masked Interrupt Status (GPIOMIS) registers (see page 238 and page 239). As the name implies, the GPIOMIS register only shows interrupt conditions that are allowed to be passed to the controller. The GPIORIS register indicates that a GPIO pin meets the conditions for an interrupt, but has not necessarily been sent to the controller. Interrupts are cleared by writing a 1 to the appropriate bit of the GPIO Interrupt Clear (GPIOICR) register (see page 240). When programming the following interrupt control registers, the interrupts should be masked (GPIOIM set to 0). Writing any value to an interrupt control register (GPIOIS, GPIOIBE, or GPIOIEV) can generate a spurious interrupt if the corresponding bits are enabled. 7.2.3 Mode Control The GPIO pins can be controlled by either hardware or software. When hardware control is enabled via the GPIO Alternate Function Select (GPIOAFSEL) register (see page 241), the pin state is controlled by its alternate function (that is, the peripheral). Software control corresponds to GPIO mode, where the GPIODATA register is used to read/write the corresponding pins. 7.2.4 Pad Control The pad control registers allow for GPIO pad configuration by software based on the application requirements. The pad control registers include the GPIODR2R, GPIODR4R, GPIODR8R, GPIOODR, GPIOPUR, GPIOPDR, GPIOSLR, and GPIODEN registers. These registers control drive strength, open-drain configuration, pull-up and pull-down resistors, slew-rate control and digital enable. 7.2.5 Identification The identification registers configured at reset allow software to detect and identify the module as a GPIO block. The identification registers include the GPIOPeriphID0-GPIOPeriphID7 registers as well as the GPIOPCellID0-GPIOPCellID3 registers. 7.3 Initialization and Configuration To use the GPIO, the peripheral clock must be enabled by setting the appropriate GPIO Port bit field (GPIOn) in the RCGC2 register. 228 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller On reset, all GPIO pins (except for the five JTAG pins) default to general-purpose input mode (GPIODIR=0 and GPIOAFSEL=0). Table 7-4 on page 229 shows all possible configurations of the GPIO pads and the control register settings required to achieve them. Table 7-5 on page 229 shows how a rising edge interrupt would be configured for pin 2 of a GPIO port. Table 7-4. GPIO Pad Configuration Examples a GPIO Register Bit Value Configuration AFSEL Digital Input (GPIO) DIR 0 ODR 0 DEN 0 PUR 1 PDR ? ? DR2R DR4R DR8R X X X SLR X Digital Output (GPIO) 0 1 0 1 ? ? ? ? ? ? Open Drain Output (GPIO) 0 1 1 1 X X ? ? ? ? Open Drain Input/Output (I2C) 1 X 1 1 X X ? ? ? ? Digital Input (Timer CCP) 1 X 0 1 ? ? X X X X Digital Output (Timer PWM) 1 X 0 1 ? ? ? ? ? ? Digital Input/Output (SSI) 1 X 0 1 ? ? ? ? ? ? Digital Input/Output (UART) 1 X 0 1 ? ? ? ? ? ? Analog Input (Comparator) 0 0 0 0 0 0 X X X X Digital Output (Comparator) 1 X 0 1 ? ? ? ? ? ? a. X=Ignored (don’t care bit) ?=Can be either 0 or 1, depending on the configuration Table 7-5. GPIO Interrupt Configuration Example Register Desired Interrupt Event Trigger GPIOIS 0=edge GPIOIBE 0=single edge a Pin 2 Bit Value 7 6 5 4 3 2 1 0 X X X X X 0 X X X X X X X 0 X X X X X X X 1 X X 0 0 0 0 0 1 0 0 1=level 1=both edges GPIOIEV 0=Low level, or negative edge 1=High level, or positive edge GPIOIM 0=masked 1=not masked a. X=Ignored (don’t care bit) July 14, 2014 229 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) 7.4 Register Map Table 7-6 on page 230 lists the GPIO registers. The offset listed is a hexadecimal increment to the register’s address, relative to that GPIO port’s base address: ■ ■ ■ ■ ■ GPIO Port A: 0x4000.4000 GPIO Port B: 0x4000.5000 GPIO Port C: 0x4000.6000 GPIO Port D: 0x4000.7000 GPIO Port E: 0x4002.4000 Note that the GPIO module clock must be enabled before the registers can be programmed (see page 196). There must be a delay of 3 system clocks after the GPIO module clock is enabled before any GPIO module registers are accessed. Important: The GPIO registers in this chapter are duplicated in each GPIO block; however, depending on the block, all eight bits may not be connected to a GPIO pad. In those cases, writing to those unconnected bits has no effect, and reading those unconnected bits returns no meaningful data. Note: The default reset value for the GPIOAFSEL register is 0x0000.0000 for all GPIO pins, with the exception of the five JTAG pins (PB7 and PC[3:0]). These five pins default to JTAG functionality. Because of this, the default reset value of GPIOAFSEL for GPIO Port B is 0x0000.0080 while the default reset value for Port C is 0x0000.000F. Table 7-6. GPIO Register Map Description See page Offset Name Type Reset 0x000 GPIODATA R/W 0x0000.0000 GPIO Data 232 0x400 GPIODIR R/W 0x0000.0000 GPIO Direction 233 0x404 GPIOIS R/W 0x0000.0000 GPIO Interrupt Sense 234 0x408 GPIOIBE R/W 0x0000.0000 GPIO Interrupt Both Edges 235 0x40C GPIOIEV R/W 0x0000.0000 GPIO Interrupt Event 236 0x410 GPIOIM R/W 0x0000.0000 GPIO Interrupt Mask 237 0x414 GPIORIS RO 0x0000.0000 GPIO Raw Interrupt Status 238 0x418 GPIOMIS RO 0x0000.0000 GPIO Masked Interrupt Status 239 0x41C GPIOICR W1C 0x0000.0000 GPIO Interrupt Clear 240 0x420 GPIOAFSEL R/W - GPIO Alternate Function Select 241 0x500 GPIODR2R R/W 0x0000.00FF GPIO 2-mA Drive Select 243 0x504 GPIODR4R R/W 0x0000.0000 GPIO 4-mA Drive Select 244 0x508 GPIODR8R R/W 0x0000.0000 GPIO 8-mA Drive Select 245 0x50C GPIOODR R/W 0x0000.0000 GPIO Open Drain Select 246 0x510 GPIOPUR R/W 0x0000.00FF GPIO Pull-Up Select 247 0x514 GPIOPDR R/W 0x0000.0000 GPIO Pull-Down Select 248 230 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 7-6. GPIO Register Map (continued) Name Type Reset 0x518 GPIOSLR R/W 0x0000.0000 GPIO Slew Rate Control Select 249 0x51C GPIODEN R/W 0x0000.00FF GPIO Digital Enable 250 0xFD0 GPIOPeriphID4 RO 0x0000.0000 GPIO Peripheral Identification 4 251 0xFD4 GPIOPeriphID5 RO 0x0000.0000 GPIO Peripheral Identification 5 252 0xFD8 GPIOPeriphID6 RO 0x0000.0000 GPIO Peripheral Identification 6 253 0xFDC GPIOPeriphID7 RO 0x0000.0000 GPIO Peripheral Identification 7 254 0xFE0 GPIOPeriphID0 RO 0x0000.0061 GPIO Peripheral Identification 0 255 0xFE4 GPIOPeriphID1 RO 0x0000.0000 GPIO Peripheral Identification 1 256 0xFE8 GPIOPeriphID2 RO 0x0000.0018 GPIO Peripheral Identification 2 257 0xFEC GPIOPeriphID3 RO 0x0000.0001 GPIO Peripheral Identification 3 258 0xFF0 GPIOPCellID0 RO 0x0000.000D GPIO PrimeCell Identification 0 259 0xFF4 GPIOPCellID1 RO 0x0000.00F0 GPIO PrimeCell Identification 1 260 0xFF8 GPIOPCellID2 RO 0x0000.0005 GPIO PrimeCell Identification 2 261 0xFFC GPIOPCellID3 RO 0x0000.00B1 GPIO PrimeCell Identification 3 262 7.5 Description See page Offset Register Descriptions The remainder of this section lists and describes the GPIO registers, in numerical order by address offset. July 14, 2014 231 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 1: GPIO Data (GPIODATA), offset 0x000 The GPIODATA register is the data register. In software control mode, values written in the GPIODATA register are transferred onto the GPIO port pins if the respective pins have been configured as outputs through the GPIO Direction (GPIODIR) register (see page 233). In order to write to GPIODATA, the corresponding bits in the mask, resulting from the address bus bits [9:2], must be High. Otherwise, the bit values remain unchanged by the write. Similarly, the values read from this register are determined for each bit by the mask bit derived from the address used to access the data register, bits [9:2]. Bits that are 1 in the address mask cause the corresponding bits in GPIODATA to be read, and bits that are 0 in the address mask cause the corresponding bits in GPIODATA to be read as 0, regardless of their value. A read from GPIODATA returns the last bit value written if the respective pins are configured as outputs, or it returns the value on the corresponding input pin when these are configured as inputs. All bits are cleared by a reset. GPIO Data (GPIODATA) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset DATA RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DATA R/W 0x00 GPIO Data This register is virtually mapped to 256 locations in the address space. To facilitate the reading and writing of data to these registers by independent drivers, the data read from and the data written to the registers are masked by the eight address lines ipaddr[9:2]. Reads from this register return its current state. Writes to this register only affect bits that are not masked by ipaddr[9:2] and are configured as outputs. See “Data Register Operation” on page 227 for examples of reads and writes. 232 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 2: GPIO Direction (GPIODIR), offset 0x400 The GPIODIR register is the data direction register. Bits set to 1 in the GPIODIR register configure the corresponding pin to be an output, while bits set to 0 configure the pins to be inputs. All bits are cleared by a reset, meaning all GPIO pins are inputs by default. GPIO Direction (GPIODIR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x400 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DIR RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DIR R/W 0x00 GPIO Data Direction The DIR values are defined as follows: Value Description 0 Pins are inputs. 1 Pins are outputs. July 14, 2014 233 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 3: GPIO Interrupt Sense (GPIOIS), offset 0x404 The GPIOIS register is the interrupt sense register. Bits set to 1 in GPIOIS configure the corresponding pins to detect levels, while bits set to 0 configure the pins to detect edges. All bits are cleared by a reset. GPIO Interrupt Sense (GPIOIS) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x404 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 IS RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 IS R/W 0x00 GPIO Interrupt Sense The IS values are defined as follows: Value Description 0 Edge on corresponding pin is detected (edge-sensitive). 1 Level on corresponding pin is detected (level-sensitive). 234 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 4: GPIO Interrupt Both Edges (GPIOIBE), offset 0x408 The GPIOIBE register is the interrupt both-edges register. When the corresponding bit in the GPIO Interrupt Sense (GPIOIS) register (see page 234) is set to detect edges, bits set to High in GPIOIBE configure the corresponding pin to detect both rising and falling edges, regardless of the corresponding bit in the GPIO Interrupt Event (GPIOIEV) register (see page 236). Clearing a bit configures the pin to be controlled by GPIOIEV. All bits are cleared by a reset. GPIO Interrupt Both Edges (GPIOIBE) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x408 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 IBE RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 IBE R/W 0x00 GPIO Interrupt Both Edges The IBE values are defined as follows: Value Description 0 Interrupt generation is controlled by the GPIO Interrupt Event (GPIOIEV) register (see page 236). 1 Both edges on the corresponding pin trigger an interrupt. Note: Single edge is determined by the corresponding bit in GPIOIEV. July 14, 2014 235 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 5: GPIO Interrupt Event (GPIOIEV), offset 0x40C The GPIOIEV register is the interrupt event register. Bits set to High in GPIOIEV configure the corresponding pin to detect rising edges or high levels, depending on the corresponding bit value in the GPIO Interrupt Sense (GPIOIS) register (see page 234). Clearing a bit configures the pin to detect falling edges or low levels, depending on the corresponding bit value in GPIOIS. All bits are cleared by a reset. GPIO Interrupt Event (GPIOIEV) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x40C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 IEV RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 IEV R/W 0x00 GPIO Interrupt Event The IEV values are defined as follows: Value Description 0 Falling edge or Low levels on corresponding pins trigger interrupts. 1 Rising edge or High levels on corresponding pins trigger interrupts. 236 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 6: GPIO Interrupt Mask (GPIOIM), offset 0x410 The GPIOIM register is the interrupt mask register. Bits set to High in GPIOIM allow the corresponding pins to trigger their individual interrupts and the combined GPIOINTR line. Clearing a bit disables interrupt triggering on that pin. All bits are cleared by a reset. GPIO Interrupt Mask (GPIOIM) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x410 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 IME RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 IME R/W 0x00 GPIO Interrupt Mask Enable The IME values are defined as follows: Value Description 0 Corresponding pin interrupt is masked. 1 Corresponding pin interrupt is not masked. July 14, 2014 237 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 7: GPIO Raw Interrupt Status (GPIORIS), offset 0x414 The GPIORIS register is the raw interrupt status register. Bits read High in GPIORIS reflect the status of interrupt trigger conditions detected (raw, prior to masking), indicating that all the requirements have been met, before they are finally allowed to trigger by the GPIO Interrupt Mask (GPIOIM) register (see page 237). Bits read as zero indicate that corresponding input pins have not initiated an interrupt. All bits are cleared by a reset. GPIO Raw Interrupt Status (GPIORIS) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x414 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 RIS RO 0x00 GPIO Interrupt Raw Status Reflects the status of interrupt trigger condition detection on pins (raw, prior to masking). The RIS values are defined as follows: Value Description 0 Corresponding pin interrupt requirements not met. 1 Corresponding pin interrupt has met requirements. 238 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: GPIO Masked Interrupt Status (GPIOMIS), offset 0x418 The GPIOMIS register is the masked interrupt status register. Bits read High in GPIOMIS reflect the status of input lines triggering an interrupt. Bits read as Low indicate that either no interrupt has been generated, or the interrupt is masked. GPIOMIS is the state of the interrupt after masking. GPIO Masked Interrupt Status (GPIOMIS) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x418 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset MIS RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 MIS RO 0x00 GPIO Masked Interrupt Status Masked value of interrupt due to corresponding pin. The MIS values are defined as follows: Value Description 0 Corresponding GPIO line interrupt not active. 1 Corresponding GPIO line asserting interrupt. July 14, 2014 239 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 9: GPIO Interrupt Clear (GPIOICR), offset 0x41C The GPIOICR register is the interrupt clear register. Writing a 1 to a bit in this register clears the corresponding interrupt edge detection logic register. Writing a 0 has no effect. GPIO Interrupt Clear (GPIOICR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x41C Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 W1C 0 W1C 0 W1C 0 W1C 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 IC RO 0 RO 0 RO 0 RO 0 W1C 0 W1C 0 W1C 0 W1C 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 IC W1C 0x00 GPIO Interrupt Clear The IC values are defined as follows: Value Description 0 Corresponding interrupt is unaffected. 1 Corresponding interrupt is cleared. 240 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 10: GPIO Alternate Function Select (GPIOAFSEL), offset 0x420 The GPIOAFSEL register is the mode control select register. Writing a 1 to any bit in this register selects the hardware control for the corresponding GPIO line. All bits are cleared by a reset, therefore no GPIO line is set to hardware control by default. Important: All GPIO pins are inputs by default (GPIODIR=0 and GPIOAFSEL=0), with the exception of the five JTAG pins (PB7 and PC[3:0]). The JTAG pins default to their JTAG functionality (GPIOAFSEL=1). A Power-On-Reset (POR) or asserting an external reset (RST) puts both groups of pins back to their default state. While debugging systems where PB7 is being used as a GPIO, care must be taken to ensure that a Low value is not applied to the pin when the part is reset. Because PB7 reverts to the TRST function after reset, a Low value on the pin causes the JTAG controller to be reset, resulting in a loss of JTAG communication. Caution – If the JTAG pins are used as GPIOs in a design, PB7 and PC2 cannot have external pull-down resistors connected to both of them at the same time. If both pins are pulled Low during reset, the controller has unpredictable behavior. If this happens, remove one or both of the pull-down resistors, and apply RST or power-cycle the part. It is possible to create a software sequence that prevents the debugger from connecting to the Stellaris® microcontroller. If the program code loaded into flash immediately changes the JTAG pins to their GPIO functionality, the debugger may not have enough time to connect and halt the controller before the JTAG pin functionality switches. This may lock the debugger out of the part. This can be avoided with a software routine that restores JTAG functionality based on an external or software trigger. GPIO Alternate Function Select (GPIOAFSEL) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x420 Type R/W, reset 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W - R/W - R/W - R/W - reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 AFSEL RO 0 RO 0 RO 0 RO 0 R/W - R/W - R/W - R/W - Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 241 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Bit/Field Name Type Reset 7:0 AFSEL R/W - Description GPIO Alternate Function Select The AFSEL values are defined as follows: Value Description 0 Software control of corresponding GPIO line (GPIO mode). 1 Hardware control of corresponding GPIO line (alternate hardware function). Note: The default reset value for the GPIOAFSEL register is 0x0000.0000 for all GPIO pins, with the exception of the five JTAG pins (PB7 and PC[3:0]). These five pins default to JTAG functionality. Because of this, the default reset value of GPIOAFSEL for GPIO Port B is 0x0000.0080 while the default reset value for Port C is 0x0000.000F. 242 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 11: GPIO 2-mA Drive Select (GPIODR2R), offset 0x500 The GPIODR2R register is the 2-mA drive control register. It allows for each GPIO signal in the port to be individually configured without affecting the other pads. When writing a DRV2 bit for a GPIO signal, the corresponding DRV4 bit in the GPIODR4R register and the DRV8 bit in the GPIODR8R register are automatically cleared by hardware. GPIO 2-mA Drive Select (GPIODR2R) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x500 Type R/W, reset 0x0000.00FF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DRV2 RO 0 RO 0 RO 0 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DRV2 R/W 0xFF Output Pad 2-mA Drive Enable A write of 1 to either GPIODR4[n] or GPIODR8[n] clears the corresponding 2-mA enable bit. The change is effective on the second clock cycle after the write. July 14, 2014 243 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 12: GPIO 4-mA Drive Select (GPIODR4R), offset 0x504 The GPIODR4R register is the 4-mA drive control register. It allows for each GPIO signal in the port to be individually configured without affecting the other pads. When writing the DRV4 bit for a GPIO signal, the corresponding DRV2 bit in the GPIODR2R register and the DRV8 bit in the GPIODR8R register are automatically cleared by hardware. GPIO 4-mA Drive Select (GPIODR4R) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x504 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DRV4 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DRV4 R/W 0x00 Output Pad 4-mA Drive Enable A write of 1 to either GPIODR2[n] or GPIODR8[n] clears the corresponding 4-mA enable bit. The change is effective on the second clock cycle after the write. 244 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 13: GPIO 8-mA Drive Select (GPIODR8R), offset 0x508 The GPIODR8R register is the 8-mA drive control register. It allows for each GPIO signal in the port to be individually configured without affecting the other pads. When writing the DRV8 bit for a GPIO signal, the corresponding DRV2 bit in the GPIODR2R register and the DRV4 bit in the GPIODR4R register are automatically cleared by hardware. GPIO 8-mA Drive Select (GPIODR8R) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x508 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DRV8 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DRV8 R/W 0x00 Output Pad 8-mA Drive Enable A write of 1 to either GPIODR2[n] or GPIODR4[n] clears the corresponding 8-mA enable bit. The change is effective on the second clock cycle after the write. July 14, 2014 245 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 14: GPIO Open Drain Select (GPIOODR), offset 0x50C The GPIOODR register is the open drain control register. Setting a bit in this register enables the open drain configuration of the corresponding GPIO pad. When open drain mode is enabled, the corresponding bit should also be set in the GPIO Digital Enable (GPIODEN) register (see page 250). Corresponding bits in the drive strength registers (GPIODR2R, GPIODR4R, GPIODR8R, and GPIOSLR ) can be set to achieve the desired rise and fall times. The GPIO acts as an open-drain input if the corresponding bit in the GPIODIR register is cleared. If open drain is selected while the GPIO is configured as an input, the GPIO will remain an input and the open-drain selection has no effect until the GPIO is changed to an output. When using the I2C module, in addition to configuring the pin to open drain, the GPIO Alternate Function Select (GPIOAFSEL) register bits for the I2C clock and data pins should be set to 1 (see examples in “Initialization and Configuration” on page 228). GPIO Open Drain Select (GPIOODR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x50C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 ODE RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 ODE R/W 0x00 Output Pad Open Drain Enable The ODE values are defined as follows: Value Description 0 Open drain configuration is disabled. 1 Open drain configuration is enabled. 246 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 15: GPIO Pull-Up Select (GPIOPUR), offset 0x510 The GPIOPUR register is the pull-up control register. When a bit is set to 1, it enables a weak pull-up resistor on the corresponding GPIO signal. Setting a bit in GPIOPUR automatically clears the corresponding bit in the GPIO Pull-Down Select (GPIOPDR) register (see page 248). GPIO Pull-Up Select (GPIOPUR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x510 Type R/W, reset 0x0000.00FF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PUE RO 0 RO 0 RO 0 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PUE R/W 0xFF Pad Weak Pull-Up Enable Value Description 0 The corresponding pin's weak pull-up resistor is disabled. 1 The corresponding pin's weak pull-up resistor is enabled. A write of 1 to GPIOPDR[n] clears the corresponding GPIOPUR[n] enables. The change is effective on the second clock cycle after the write. July 14, 2014 247 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 16: GPIO Pull-Down Select (GPIOPDR), offset 0x514 The GPIOPDR register is the pull-down control register. When a bit is set to 1, it enables a weak pull-down resistor on the corresponding GPIO signal. Setting a bit in GPIOPDR automatically clears the corresponding bit in the GPIO Pull-Up Select (GPIOPUR) register (see page 247). GPIO Pull-Down Select (GPIOPDR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x514 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PDE RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PDE R/W 0x00 Pad Weak Pull-Down Enable Value Description 0 The corresponding pin's weak pull-down resistor is disabled. 1 The corresponding pin's weak pull-down resistor is enabled. A write of 1 to GPIOPUR[n] clears the corresponding GPIOPDR[n] enables. The change is effective on the second clock cycle after the write. 248 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: GPIO Slew Rate Control Select (GPIOSLR), offset 0x518 The GPIOSLR register is the slew rate control register. Slew rate control is only available when using the 8-mA drive strength option via the GPIO 8-mA Drive Select (GPIODR8R) register (see page 245). GPIO Slew Rate Control Select (GPIOSLR) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x518 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 SRL RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 SRL R/W 0x00 Slew Rate Limit Enable (8-mA drive only) The SRL values are defined as follows: Value Description 0 Slew rate control disabled. 1 Slew rate control enabled. July 14, 2014 249 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 18: GPIO Digital Enable (GPIODEN), offset 0x51C Note: Pins configured as digital inputs are Schmitt-triggered. The GPIODEN register is the digital enable register. By default, all GPIO signals are configured as digital inputs at reset. If a pin is being used as a GPIO or its Alternate Hardware Function, it should be configured as a digital input. The only time that a pin should not be configured as a digital input is when the GPIO pin is configured to be one of the analog input signals for the analog comparators. GPIO Digital Enable (GPIODEN) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0x51C Type R/W, reset 0x0000.00FF 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset reserved Type Reset DEN RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DEN R/W 0xFF Digital Enable The DEN values are defined as follows: Value Description 0 Digital functions disabled. 1 Digital functions enabled. 250 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 19: GPIO Peripheral Identification 4 (GPIOPeriphID4), offset 0xFD0 The GPIOPeriphID4, GPIOPeriphID5, GPIOPeriphID6, and GPIOPeriphID7 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 4 (GPIOPeriphID4) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID4 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID4 RO 0x00 GPIO Peripheral ID Register[7:0] July 14, 2014 251 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 20: GPIO Peripheral Identification 5 (GPIOPeriphID5), offset 0xFD4 The GPIOPeriphID4, GPIOPeriphID5, GPIOPeriphID6, and GPIOPeriphID7 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 5 (GPIOPeriphID5) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID5 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID5 RO 0x00 GPIO Peripheral ID Register[15:8] 252 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 21: GPIO Peripheral Identification 6 (GPIOPeriphID6), offset 0xFD8 The GPIOPeriphID4, GPIOPeriphID5, GPIOPeriphID6, and GPIOPeriphID7 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 6 (GPIOPeriphID6) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID6 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID6 RO 0x00 GPIO Peripheral ID Register[23:16] July 14, 2014 253 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 22: GPIO Peripheral Identification 7 (GPIOPeriphID7), offset 0xFDC The GPIOPeriphID4, GPIOPeriphID5, GPIOPeriphID6, and GPIOPeriphID7 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 7 (GPIOPeriphID7) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID7 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID7 RO 0x00 GPIO Peripheral ID Register[31:24] 254 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 23: GPIO Peripheral Identification 0 (GPIOPeriphID0), offset 0xFE0 The GPIOPeriphID0, GPIOPeriphID1, GPIOPeriphID2, and GPIOPeriphID3 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 0 (GPIOPeriphID0) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFE0 Type RO, reset 0x0000.0061 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID0 RO 0x61 GPIO Peripheral ID Register[7:0] Can be used by software to identify the presence of this peripheral. July 14, 2014 255 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 24: GPIO Peripheral Identification 1 (GPIOPeriphID1), offset 0xFE4 The GPIOPeriphID0, GPIOPeriphID1, GPIOPeriphID2, and GPIOPeriphID3 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 1 (GPIOPeriphID1) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFE4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID1 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID1 RO 0x00 GPIO Peripheral ID Register[15:8] Can be used by software to identify the presence of this peripheral. 256 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 25: GPIO Peripheral Identification 2 (GPIOPeriphID2), offset 0xFE8 The GPIOPeriphID0, GPIOPeriphID1, GPIOPeriphID2, and GPIOPeriphID3 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 2 (GPIOPeriphID2) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID2 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID2 RO 0x18 GPIO Peripheral ID Register[23:16] Can be used by software to identify the presence of this peripheral. July 14, 2014 257 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 26: GPIO Peripheral Identification 3 (GPIOPeriphID3), offset 0xFEC The GPIOPeriphID0, GPIOPeriphID1, GPIOPeriphID2, and GPIOPeriphID3 registers can conceptually be treated as one 32-bit register; each register contains eight bits of the 32-bit register, used by software to identify the peripheral. GPIO Peripheral Identification 3 (GPIOPeriphID3) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID3 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID3 RO 0x01 GPIO Peripheral ID Register[31:24] Can be used by software to identify the presence of this peripheral. 258 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 27: GPIO PrimeCell Identification 0 (GPIOPCellID0), offset 0xFF0 The GPIOPCellID0, GPIOPCellID1, GPIOPCellID2, and GPIOPCellID3 registers are four 8-bit wide registers, that can conceptually be treated as one 32-bit register. The register is used as a standard cross-peripheral identification system. GPIO PrimeCell Identification 0 (GPIOPCellID0) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID0 RO 0x0D GPIO PrimeCell ID Register[7:0] Provides software a standard cross-peripheral identification system. July 14, 2014 259 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 28: GPIO PrimeCell Identification 1 (GPIOPCellID1), offset 0xFF4 The GPIOPCellID0, GPIOPCellID1, GPIOPCellID2, and GPIOPCellID3 registers are four 8-bit wide registers, that can conceptually be treated as one 32-bit register. The register is used as a standard cross-peripheral identification system. GPIO PrimeCell Identification 1 (GPIOPCellID1) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID1 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 1 RO 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID1 RO 0xF0 GPIO PrimeCell ID Register[15:8] Provides software a standard cross-peripheral identification system. 260 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 29: GPIO PrimeCell Identification 2 (GPIOPCellID2), offset 0xFF8 The GPIOPCellID0, GPIOPCellID1, GPIOPCellID2, and GPIOPCellID3 registers are four 8-bit wide registers, that can conceptually be treated as one 32-bit register. The register is used as a standard cross-peripheral identification system. GPIO PrimeCell Identification 2 (GPIOPCellID2) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID2 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID2 RO 0x05 GPIO PrimeCell ID Register[23:16] Provides software a standard cross-peripheral identification system. July 14, 2014 261 Texas Instruments-Production Data General-Purpose Input/Outputs (GPIOs) Register 30: GPIO PrimeCell Identification 3 (GPIOPCellID3), offset 0xFFC The GPIOPCellID0, GPIOPCellID1, GPIOPCellID2, and GPIOPCellID3 registers are four 8-bit wide registers, that can conceptually be treated as one 32-bit register. The register is used as a standard cross-peripheral identification system. GPIO PrimeCell Identification 3 (GPIOPCellID3) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CID3 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 1 RO 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID3 RO 0xB1 GPIO PrimeCell ID Register[31:24] Provides software a standard cross-peripheral identification system. 262 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 8 General-Purpose Timers Programmable timers can be used to count or time external events that drive the Timer input pins. ® The Stellaris General-Purpose Timer Module (GPTM) contains three GPTM blocks (Timer0, Timer1, and Timer 2). Each GPTM block provides two 16-bit timers/counters (referred to as TimerA and TimerB) that can be configured to operate independently as timers or event counters, or configured to operate as one 32-bit timer or one 32-bit Real-Time Clock (RTC). The GPT Module is one timing resource available on the Stellaris microcontrollers. Other timer resources include the System Timer (SysTick) (see 82). The General-Purpose Timers provide the following features: ■ Three General-Purpose Timer Modules (GPTM), each of which provides two 16-bit timers/counters. Each GPTM can be configured to operate independently: – As a single 32-bit timer – As one 32-bit Real-Time Clock (RTC) to event capture – For Pulse Width Modulation (PWM) ■ 32-bit Timer modes – Programmable one-shot timer – Programmable periodic timer – Real-Time Clock when using an external 32.768-KHz clock as the input – User-enabled stalling when the controller asserts CPU Halt flag during debug ■ 16-bit Timer modes – General-purpose timer function with an 8-bit prescaler (for one-shot and periodic modes only) – Programmable one-shot timer – Programmable periodic timer – User-enabled stalling when the controller asserts CPU Halt flag during debug ■ 16-bit Input Capture modes – Input edge count capture – Input edge time capture ■ 16-bit PWM mode – Simple PWM mode with software-programmable output inversion of the PWM signal 8.1 Block Diagram Note: In Figure 8-1 on page 264, the specific CCP pins available depend on the Stellaris device. See Table 8-1 on page 264 for the available CCPs. July 14, 2014 263 Texas Instruments-Production Data General-Purpose Timers Figure 8-1. GPTM Module Block Diagram 0x0000 (Down Counter Modes) TimerA Control GPTMTAPMR TA Comparator GPTMTAPR Clock / Edge Detect GPTMTAMATCHR Interrupt / Config TimerA Interrupt GPTMTAILR GPTMAR En GPTMTAMR GPTMCFG GPTMCTL GPTMIMR TimerB Interrupt 32 KHz or Even CCP Pin RTC Divider GPTMRIS GPTMMIS TimerB Control GPTMICR GPTMTBR En GPTMTBPMR Clock / Edge Detect GPTMTBPR GPTMTBMATCHR Odd CCP Pin TB Comparator GPTMTBILR GPTMTBMR 0x0000 (Down Counter Modes) System Clock Table 8-1. Available CCP Pins Timer 16-Bit Up/Down Counter Timer 0 Timer 1 Timer 2 8.2 Even CCP Pin Odd CCP Pin TimerA CCP0 - TimerB - CCP1 TimerA CCP2 - TimerB - CCP3 TimerA CCP4 - TimerB - CCP5 Signal Description Table 8-2 on page 264lists the external signals of the GP Timer module and describes the function of each. The GP Timer signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Assignment" lists the possible GPIO pin placements for these GP Timer signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the GP Timer function. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 8-2. General-Purpose Timers Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type CCP0 45 I/O TTL Description Capture/Compare/PWM 0. CCP1 3 I/O TTL Capture/Compare/PWM 1. CCP2 46 I/O TTL Capture/Compare/PWM 2. 264 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 8-2. General-Purpose Timers Signals (48QFP) (continued) a Pin Name Pin Number Pin Type Buffer Type Description CCP3 2 I/O TTL Capture/Compare/PWM 3. CCP4 4 I/O TTL Capture/Compare/PWM 4. CCP5 1 I/O TTL Capture/Compare/PWM 5. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 8.3 Functional Description The main components of each GPTM block are two free-running 16-bit up/down counters (referred to as TimerA and TimerB), two 16-bit match registers, two prescaler match registers, and two 16-bit load/initialization registers and their associated control functions. The exact functionality of each GPTM is controlled by software and configured through the register interface. Software configures the GPTM using the GPTM Configuration (GPTMCFG) register (see page 275), the GPTM TimerA Mode (GPTMTAMR) register (see page 276), and the GPTM TimerB Mode (GPTMTBMR) register (see page 278). When in one of the 32-bit modes, the timer can only act as a 32-bit timer. However, when configured in 16-bit mode, the GPTM can have its two 16-bit timers configured in any combination of the 16-bit modes. 8.3.1 GPTM Reset Conditions After reset has been applied to the GPTM module, the module is in an inactive state, and all control registers are cleared and in their default states. Counters TimerA and TimerB are initialized to 0xFFFF, along with their corresponding load registers: the GPTM TimerA Interval Load (GPTMTAILR) register (see page 289) and the GPTM TimerB Interval Load (GPTMTBILR) register (see page 290). The prescale counters are initialized to 0x00: the GPTM TimerA Prescale (GPTMTAPR) register (see page 293) and the GPTM TimerB Prescale (GPTMTBPR) register (see page 294). 8.3.2 32-Bit Timer Operating Modes This section describes the three GPTM 32-bit timer modes (One-Shot, Periodic, and RTC) and their configuration. The GPTM is placed into 32-bit mode by writing a 0 (One-Shot/Periodic 32-bit timer mode) or a 1 (RTC mode) to the GPTM Configuration (GPTMCFG) register. In both configurations, certain GPTM registers are concatenated to form pseudo 32-bit registers. These registers include: ■ GPTM TimerA Interval Load (GPTMTAILR) register [15:0], see page 289 ■ GPTM TimerB Interval Load (GPTMTBILR) register [15:0], see page 290 ■ GPTM TimerA (GPTMTAR) register [15:0], see page 297 ■ GPTM TimerB (GPTMTBR) register [15:0], see page 298 In the 32-bit modes, the GPTM translates a 32-bit write access to GPTMTAILR into a write access to both GPTMTAILR and GPTMTBILR. The resulting word ordering for such a write operation is: GPTMTBILR[15:0]:GPTMTAILR[15:0] Likewise, a read access to GPTMTAR returns the value: GPTMTBR[15:0]:GPTMTAR[15:0] July 14, 2014 265 Texas Instruments-Production Data General-Purpose Timers 8.3.2.1 32-Bit One-Shot/Periodic Timer Mode In 32-bit one-shot and periodic timer modes, the concatenated versions of the TimerA and TimerB registers are configured as a 32-bit down-counter. The selection of one-shot or periodic mode is determined by the value written to the TAMR field of the GPTM TimerA Mode (GPTMTAMR) register (see page 276), and there is no need to write to the GPTM TimerB Mode (GPTMTBMR) register. When software writes the TAEN bit in the GPTM Control (GPTMCTL) register (see page 280), the timer begins counting down from its preloaded value. Once the 0x0000.0000 state is reached, the timer reloads its start value from the concatenated GPTMTAILR on the next cycle. If configured to be a one-shot timer, the timer stops counting and clears the TAEN bit in the GPTMCTL register. If configured as a periodic timer, it continues counting. In addition to reloading the count value, the GPTM generates interrupts and triggers when it reaches the 0x000.0000 state. The GPTM sets the TATORIS bit in the GPTM Raw Interrupt Status (GPTMRIS) register (see page 285), and holds it until it is cleared by writing the GPTM Interrupt Clear (GPTMICR) register (see page 287). If the time-out interrupt is enabled in the GPTM Interrupt Mask (GPTMIMR) register (see page 283), the GPTM also sets the TATOMIS bit in the GPTM Masked Interrupt Status (GPTMMIS) register (see page 286). If software reloads the GPTMTAILR register while the counter is running, the counter loads the new value on the next clock cycle and continues counting from the new value. If the TASTALL bit in the GPTMCTL register is set, the timer freezes counting while the processor is halted by the debugger. The timer resumes counting when the processor resumes execution. 8.3.2.2 32-Bit Real-Time Clock Timer Mode In Real-Time Clock (RTC) mode, the concatenated versions of the TimerA and TimerB registers are configured as a 32-bit up-counter. When RTC mode is selected for the first time, the counter is loaded with a value of 0x0000.0001. All subsequent load values must be written to the GPTM TimerA Match (GPTMTAMATCHR) register (see page 291) by the controller. The input clock on an even CCP input is required to be 32.768 KHz in RTC mode. The clock signal is then divided down to a 1 Hz rate and is passed along to the input of the 32-bit counter. When software writes the TAEN bit inthe GPTMCTL register, the counter starts counting up from its preloaded value of 0x0000.0001. When the current count value matches the preloaded value in the GPTMTAMATCHR register, it rolls over to a value of 0x0000.0000 and continues counting until either a hardware reset, or it is disabled by software (clearing the TAEN bit). When a match occurs, the GPTM asserts the RTCRIS bit in GPTMRIS. If the RTC interrupt is enabled in GPTMIMR, the GPTM also sets the RTCMIS bit in GPTMMIS and generates a controller interrupt. The status flags are cleared by writing the RTCCINT bit in GPTMICR. If the TASTALL and/or TBSTALL bits in the GPTMCTL register are set, the timer does not freeze if the RTCEN bit is set in GPTMCTL. 8.3.3 16-Bit Timer Operating Modes The GPTM is placed into global 16-bit mode by writing a value of 0x4 to the GPTM Configuration (GPTMCFG) register (see page 275). This section describes each of the GPTM 16-bit modes of operation. TimerA and TimerB have identical modes, so a single description is given using an n to reference both. 8.3.3.1 16-Bit One-Shot/Periodic Timer Mode In 16-bit one-shot and periodic timer modes, the timer is configured as a 16-bit down-counter with an optional 8-bit prescaler that effectively extends the counting range of the timer to 24 bits. The 266 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller selection of one-shot or periodic mode is determined by the value written to the TnMR field of the GPTMTnMR register. The optional prescaler is loaded into the GPTM Timern Prescale (GPTMTnPR) register. When software writes the TnEN bit in the GPTMCTL register, the timer begins counting down from its preloaded value. Once the 0x0000 state is reached, the timer reloads its start value from GPTMTnILR and GPTMTnPR on the next cycle. If configured to be a one-shot timer, the timer stops counting and clears the TnEN bit in the GPTMCTL register. If configured as a periodic timer, it continues counting. In addition to reloading the count value, the timer generates interrupts and triggers when it reaches the 0x0000 state. The GPTM sets the TnTORIS bit in the GPTMRIS register, and holds it until it is cleared by writing the GPTMICR register. If the time-out interrupt is enabled in GPTMIMR, the GPTM also sets the TnTOMIS bit in GPTMISR and generates a controller interrupt. If software reloads the GPTMTAILR register while the counter is running, the counter loads the new value on the next clock cycle and continues counting from the new value. If the TnSTALL bit in the GPTMCTL register is set, the timer freezes counting while the processor is halted by the debugger. The timer resumes counting when the processor resumes execution. The following example shows a variety of configurations for a 16-bit free running timer while using the prescaler. All values assume a 50-MHz clock with Tc=20 ns (clock period). Table 8-3. 16-Bit Timer With Prescaler Configurations a Prescale #Clock (T c) Max Time Units 00000000 1 1.3107 mS 00000001 2 2.6214 mS 00000010 3 3.9322 mS ------------ -- -- -- 11111101 254 332.9229 mS 11111110 255 334.2336 mS 11111111 256 335.5443 mS a. Tc is the clock period. 8.3.3.2 16-Bit Input Edge Count Mode Note: For rising-edge detection, the input signal must be High for at least two system clock periods following the rising edge. Similarly, for falling-edge detection, the input signal must be Low for at least two system clock periods following the falling edge. Based on this criteria, the maximum input frequency for edge detection is 1/4 of the system frequency. Note: The prescaler is not available in 16-Bit Input Edge Count mode. In Edge Count mode, the timer is configured as a down-counter capable of capturing three types of events: rising edge, falling edge, or both. To place the timer in Edge Count mode, the TnCMR bit of the GPTMTnMR register must be set to 0. The type of edge that the timer counts is determined by the TnEVENT fields of the GPTMCTL register. During initialization, the GPTM Timern Match (GPTMTnMATCHR) register is configured so that the difference between the value in the GPTMTnILR register and the GPTMTnMATCHR register equals the number of edge events that must be counted. When software writes the TnEN bit in the GPTM Control (GPTMCTL) register, the timer is enabled for event capture. Each input event on the CCP pin decrements the counter by 1 until the event count July 14, 2014 267 Texas Instruments-Production Data General-Purpose Timers matches GPTMTnMATCHR. When the counts match, the GPTM asserts the CnMRIS bit in the GPTMRIS register (and the CnMMIS bit, if the interrupt is not masked). The counter is then reloaded using the value in GPTMTnILR, and stopped since the GPTM automatically clears the TnEN bit in the GPTMCTL register. Once the event count has been reached, all further events are ignored until TnEN is re-enabled by software. Figure 8-2 on page 268 shows how input edge count mode works. In this case, the timer start value is set to GPTMTnILR =0x000A and the match value is set to GPTMTnMATCHR =0x0006 so that four edge events are counted. The counter is configured to detect both edges of the input signal. Note that the last two edges are not counted since the timer automatically clears the TnEN bit after the current count matches the value in the GPTMTnMATCHR register. Figure 8-2. 16-Bit Input Edge Count Mode Example Timer stops, flags asserted Count Timer reload on next cycle Ignored Ignored 0x000A 0x0009 0x0008 0x0007 0x0006 Input Signal 8.3.3.3 16-Bit Input Edge Time Mode Note: For rising-edge detection, the input signal must be High for at least two system clock periods following the rising edge. Similarly, for falling edge detection, the input signal must be Low for at least two system clock periods following the falling edge. Based on this criteria, the maximum input frequency for edge detection is 1/4 of the system frequency. Note: The prescaler is not available in 16-Bit Input Edge Time mode. In Edge Time mode, the timer is configured as a free-running down-counter initialized to the value loaded in the GPTMTnILR register (or 0xFFFF at reset). The timer is capable of capturing three types of events: rising edge, falling edge, or both. The timer is placed into Edge Time mode by setting the TnCMR bit in the GPTMTnMR register, and the type of event that the timer captures is determined by the TnEVENT fields of the GPTMCTL register. When software writes the TnEN bit in the GPTMCTL register, the timer is enabled for event capture. When the selected input event is detected, the current Tn counter value is captured in the GPTMTnR register and is available to be read by the controller. The GPTM then asserts the CnERIS bit (and the CnEMIS bit, if the interrupt is not masked). 268 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller After an event has been captured, the timer does not stop counting. It continues to count until the TnEN bit is cleared. When the timer reaches the 0x0000 state, it is reloaded with the value from the GPTMTnILR register. Figure 8-3 on page 269 shows how input edge timing mode works. In the diagram, it is assumed that the start value of the timer is the default value of 0xFFFF, and the timer is configured to capture rising edge events. Each time a rising edge event is detected, the current count value is loaded into the GPTMTnR register, and is held there until another rising edge is detected (at which point the new count value is loaded into GPTMTnR). Figure 8-3. 16-Bit Input Edge Time Mode Example Count 0xFFFF GPTMTnR=X GPTMTnR=Y GPTMTnR=Z Z X Y Time Input Signal 8.3.3.4 16-Bit PWM Mode Note: The prescaler is not available in 16-Bit PWM mode. The GPTM supports a simple PWM generation mode. In PWM mode, the timer is configured as a down-counter with a start value (and thus period) defined by GPTMTnILR. In this mode, the PWM frequency and period are synchronous events and therefore guaranteed to be glitch free. PWM mode is enabled with the GPTMTnMR register by setting the TnAMS bit to 0x1, the TnCMR bit to 0x0, and the TnMR field to 0x2. When software writes the TnEN bit in the GPTMCTL register, the counter begins counting down until it reaches the 0x0000 state. On the next counter cycle, the counter reloads its start value from GPTMTnILR and continues counting until disabled by software clearing the TnEN bit in the GPTMCTL register. No interrupts or status bits are asserted in PWM mode. The output PWM signal asserts when the counter is at the value of the GPTMTnILR register (its start state), and is deasserted when the counter value equals the value in the GPTM Timern Match Register (GPTMTnMATCHR). Software has the capability of inverting the output PWM signal by setting the TnPWML bit in the GPTMCTL register. Figure 8-4 on page 270 shows how to generate an output PWM with a 1-ms period and a 66% duty cycle assuming a 50-MHz input clock and TnPWML =0 (duty cycle would be 33% for the TnPWML July 14, 2014 269 Texas Instruments-Production Data General-Purpose Timers =1 configuration). For this example, the start value is GPTMTnIRL=0xC350 and the match value is GPTMTnMATCHR=0x411A. Figure 8-4. 16-Bit PWM Mode Example Count GPTMTnR=GPTMnMR GPTMTnR=GPTMnMR 0xC350 0x411A Time TnEN set TnPWML = 0 Output Signal TnPWML = 1 8.4 Initialization and Configuration To use the general-purpose timers, the peripheral clock must be enabled by setting the TIMER0, TIMER1, and TIMER2 bits in the RCGC1 register. This section shows module initialization and configuration examples for each of the supported timer modes. 8.4.1 32-Bit One-Shot/Periodic Timer Mode The GPTM is configured for 32-bit One-Shot and Periodic modes by the following sequence: 1. Ensure the timer is disabled (the TAEN bit in the GPTMCTL register is cleared) before making any changes. 2. Write the GPTM Configuration Register (GPTMCFG) with a value of 0x0. 3. Set the TAMR field in the GPTM TimerA Mode Register (GPTMTAMR): a. Write a value of 0x1 for One-Shot mode. b. Write a value of 0x2 for Periodic mode. 4. Load the start value into the GPTM TimerA Interval Load Register (GPTMTAILR). 5. If interrupts are required, set the TATOIM bit in the GPTM Interrupt Mask Register (GPTMIMR). 270 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 6. Set the TAEN bit in the GPTMCTL register to enable the timer and start counting. 7. Poll the TATORIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled). In both cases, the status flags are cleared by writing a 1 to the TATOCINT bit of the GPTM Interrupt Clear Register (GPTMICR). In One-Shot mode, the timer stops counting after step 7 on page 271. To re-enable the timer, repeat the sequence. A timer configured in Periodic mode does not stop counting after it times out. 8.4.2 32-Bit Real-Time Clock (RTC) Mode To use the RTC mode, the timer must have a 32.768-KHz input signal on an even CCP input. To enable the RTC feature, follow these steps: 1. Ensure the timer is disabled (the TAEN bit is cleared) before making any changes. 2. Write the GPTM Configuration Register (GPTMCFG) with a value of 0x1. 3. Write the desired match value to the GPTM TimerA Match Register (GPTMTAMATCHR). 4. Set/clear the RTCEN bit in the GPTM Control Register (GPTMCTL) as desired. 5. If interrupts are required, set the RTCIM bit in the GPTM Interrupt Mask Register (GPTMIMR). 6. Set the TAEN bit in the GPTMCTL register to enable the timer and start counting. When the timer count equals the value in the GPTMTAMATCHR register, the GPTM asserts the RTCRIS bit in the GPTMRIS register and continues counting until Timer A is disabled or a hardware reset. The interrupt is cleared by writing the RTCCINT bit in the GPTMICR register. 8.4.3 16-Bit One-Shot/Periodic Timer Mode A timer is configured for 16-bit One-Shot and Periodic modes by the following sequence: 1. Ensure the timer is disabled (the TnEN bit is cleared) before making any changes. 2. Write the GPTM Configuration Register (GPTMCFG) with a value of 0x4. 3. Set the TnMR field in the GPTM Timer Mode (GPTMTnMR) register: a. Write a value of 0x1 for One-Shot mode. b. Write a value of 0x2 for Periodic mode. 4. If a prescaler is to be used, write the prescale value to the GPTM Timern Prescale Register (GPTMTnPR). 5. Load the start value into the GPTM Timer Interval Load Register (GPTMTnILR). 6. If interrupts are required, set the TnTOIM bit in the GPTM Interrupt Mask Register (GPTMIMR). 7. Set the TnEN bit in the GPTM Control Register (GPTMCTL) to enable the timer and start counting. July 14, 2014 271 Texas Instruments-Production Data General-Purpose Timers 8. Poll the TnTORIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled). In both cases, the status flags are cleared by writing a 1 to the TnTOCINT bit of the GPTM Interrupt Clear Register (GPTMICR). In One-Shot mode, the timer stops counting after step 8 on page 272. To re-enable the timer, repeat the sequence. A timer configured in Periodic mode does not stop counting after it times out. 8.4.4 16-Bit Input Edge Count Mode A timer is configured to Input Edge Count mode by the following sequence: 1. Ensure the timer is disabled (the TnEN bit is cleared) before making any changes. 2. Write the GPTM Configuration (GPTMCFG) register with a value of 0x4. 3. In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x0 and the TnMR field to 0x3. 4. Configure the type of event(s) that the timer captures by writing the TnEVENT field of the GPTM Control (GPTMCTL) register. 5. Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register. 6. Load the desired event count into the GPTM Timern Match (GPTMTnMATCHR) register. 7. If interrupts are required, set the CnMIM bit in the GPTM Interrupt Mask (GPTMIMR) register. 8. Set the TnEN bit in the GPTMCTL register to enable the timer and begin waiting for edge events. 9. Poll the CnMRIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled). In both cases, the status flags are cleared by writing a 1 to the CnMCINT bit of the GPTM Interrupt Clear (GPTMICR) register. In Input Edge Count Mode, the timer stops after the desired number of edge events has been detected. To re-enable the timer, ensure that the TnEN bit is cleared and repeat step 4 on page 272 through step 9 on page 272. 8.4.5 16-Bit Input Edge Timing Mode A timer is configured to Input Edge Timing mode by the following sequence: 1. Ensure the timer is disabled (the TnEN bit is cleared) before making any changes. 2. Write the GPTM Configuration (GPTMCFG) register with a value of 0x4. 3. In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x1 and the TnMR field to 0x3. 4. Configure the type of event that the timer captures by writing the TnEVENT field of the GPTM Control (GPTMCTL) register. 5. Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register. 6. If interrupts are required, set the CnEIM bit in the GPTM Interrupt Mask (GPTMIMR) register. 7. Set the TnEN bit in the GPTM Control (GPTMCTL) register to enable the timer and start counting. 272 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 8. Poll the CnERIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled). In both cases, the status flags are cleared by writing a 1 to the CnECINT bit of the GPTM Interrupt Clear (GPTMICR) register. The time at which the event happened can be obtained by reading the GPTM Timern (GPTMTnR) register. In Input Edge Timing mode, the timer continues running after an edge event has been detected, but the timer interval can be changed at any time by writing the GPTMTnILR register. The change takes effect at the next cycle after the write. 8.4.6 16-Bit PWM Mode A timer is configured to PWM mode using the following sequence: 1. Ensure the timer is disabled (the TnEN bit is cleared) before making any changes. 2. Write the GPTM Configuration (GPTMCFG) register with a value of 0x4. 3. In the GPTM Timer Mode (GPTMTnMR) register, set the TnAMS bit to 0x1, the TnCMR bit to 0x0, and the TnMR field to 0x2. 4. Configure the output state of the PWM signal (whether or not it is inverted) in the TnPWML field of the GPTM Control (GPTMCTL) register. 5. Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register. 6. Load the GPTM Timern Match (GPTMTnMATCHR) register with the desired value. 7. Set the TnEN bit in the GPTM Control (GPTMCTL) register to enable the timer and begin generation of the output PWM signal. In PWM Timing mode, the timer continues running after the PWM signal has been generated. The PWM period can be adjusted at any time by writing the GPTMTnILR register, and the change takes effect at the next cycle after the write. 8.5 Register Map Table 8-4 on page 273 lists the GPTM registers. The offset listed is a hexadecimal increment to the register’s address, relative to that timer’s base address: ■ Timer0: 0x4003.0000 ■ Timer1: 0x4003.1000 ■ Timer2: 0x4003.2000 Note that the Timer module clock must be enabled before the registers can be programmed (see page 190). There must be a delay of 3 system clocks after the Timer module clock is enabled before any Timer module registers are accessed. Table 8-4. Timers Register Map Description See page Offset Name Type Reset 0x000 GPTMCFG R/W 0x0000.0000 GPTM Configuration 275 0x004 GPTMTAMR R/W 0x0000.0000 GPTM TimerA Mode 276 July 14, 2014 273 Texas Instruments-Production Data General-Purpose Timers Table 8-4. Timers Register Map (continued) Name Type Reset 0x008 GPTMTBMR R/W 0x0000.0000 GPTM TimerB Mode 278 0x00C GPTMCTL R/W 0x0000.0000 GPTM Control 280 0x018 GPTMIMR R/W 0x0000.0000 GPTM Interrupt Mask 283 0x01C GPTMRIS RO 0x0000.0000 GPTM Raw Interrupt Status 285 0x020 GPTMMIS RO 0x0000.0000 GPTM Masked Interrupt Status 286 0x024 GPTMICR W1C 0x0000.0000 GPTM Interrupt Clear 287 0x028 GPTMTAILR R/W 0xFFFF.FFFF GPTM TimerA Interval Load 289 0x02C GPTMTBILR R/W 0x0000.FFFF GPTM TimerB Interval Load 290 0x030 GPTMTAMATCHR R/W 0xFFFF.FFFF GPTM TimerA Match 291 0x034 GPTMTBMATCHR R/W 0x0000.FFFF GPTM TimerB Match 292 0x038 GPTMTAPR R/W 0x0000.0000 GPTM TimerA Prescale 293 0x03C GPTMTBPR R/W 0x0000.0000 GPTM TimerB Prescale 294 0x040 GPTMTAPMR R/W 0x0000.0000 GPTM TimerA Prescale Match 295 0x044 GPTMTBPMR R/W 0x0000.0000 GPTM TimerB Prescale Match 296 0x048 GPTMTAR RO 0xFFFF.FFFF GPTM TimerA 297 0x04C GPTMTBR RO 0x0000.FFFF GPTM TimerB 298 8.6 Description See page Offset Register Descriptions The remainder of this section lists and describes the GPTM registers, in numerical order by address offset. 274 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 1: GPTM Configuration (GPTMCFG), offset 0x000 This register configures the global operation of the GPTM module. The value written to this register determines whether the GPTM is in 32- or 16-bit mode. GPTM Configuration (GPTMCFG) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 GPTMCFG R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2:0 GPTMCFG R/W 0x0 GPTM Configuration The GPTMCFG values are defined as follows: Value Description 0x0 32-bit timer configuration. 0x1 32-bit real-time clock (RTC) counter configuration. 0x2 Reserved 0x3 Reserved 0x4-0x7 16-bit timer configuration, function is controlled by bits 1:0 of GPTMTAMR and GPTMTBMR. July 14, 2014 275 Texas Instruments-Production Data General-Purpose Timers Register 2: GPTM TimerA Mode (GPTMTAMR), offset 0x004 This register configures the GPTM based on the configuration selected in the GPTMCFG register. When in 16-bit PWM mode, set the TAAMS bit to 0x1, the TACMR bit to 0x0, and the TAMR field to 0x2. GPTM TimerA Mode (GPTMTAMR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TAAMS TACMR RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TAMR R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TAAMS R/W 0 GPTM TimerA Alternate Mode Select The TAAMS values are defined as follows: Value Description 0 Capture mode is enabled. 1 PWM mode is enabled. Note: 2 TACMR R/W 0 To enable PWM mode, you must also clear the TACMR bit and set the TAMR field to 0x2. GPTM TimerA Capture Mode The TACMR values are defined as follows: Value Description 0 Edge-Count mode 1 Edge-Time mode 276 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 1:0 TAMR R/W 0x0 Description GPTM TimerA Mode The TAMR values are defined as follows: Value Description 0x0 Reserved 0x1 One-Shot Timer mode 0x2 Periodic Timer mode 0x3 Capture mode The Timer mode is based on the timer configuration defined by bits 2:0 in the GPTMCFG register (16-or 32-bit). In 16-bit timer configuration, TAMR controls the 16-bit timer modes for TimerA. In 32-bit timer configuration, this register controls the mode and the contents of GPTMTBMR are ignored. July 14, 2014 277 Texas Instruments-Production Data General-Purpose Timers Register 3: GPTM TimerB Mode (GPTMTBMR), offset 0x008 This register configures the GPTM based on the configuration selected in the GPTMCFG register. When in 16-bit PWM mode, set the TBAMS bit to 0x1, the TBCMR bit to 0x0, and the TBMR field to 0x2. GPTM TimerB Mode (GPTMTBMR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TBAMS TBCMR RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TBMR R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TBAMS R/W 0 GPTM TimerB Alternate Mode Select The TBAMS values are defined as follows: Value Description 0 Capture mode is enabled. 1 PWM mode is enabled. Note: 2 TBCMR R/W 0 To enable PWM mode, you must also clear the TBCMR bit and set the TBMR field to 0x2. GPTM TimerB Capture Mode The TBCMR values are defined as follows: Value Description 0 Edge-Count mode 1 Edge-Time mode 278 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 1:0 TBMR R/W 0x0 Description GPTM TimerB Mode The TBMR values are defined as follows: Value Description 0x0 Reserved 0x1 One-Shot Timer mode 0x2 Periodic Timer mode 0x3 Capture mode The timer mode is based on the timer configuration defined by bits 2:0 in the GPTMCFG register. In 16-bit timer configuration, these bits control the 16-bit timer modes for TimerB. In 32-bit timer configuration, this register’s contents are ignored and GPTMTAMR is used. July 14, 2014 279 Texas Instruments-Production Data General-Purpose Timers Register 4: GPTM Control (GPTMCTL), offset 0x00C This register is used alongside the GPTMCFG and GMTMTnMR registers to fine-tune the timer configuration, and to enable other features such as timer stall. GPTM Control (GPTMCTL) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x00C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 TBSTALL TBEN R/W 0 R/W 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 TASTALL TAEN R/W 0 R/W 0 reserved Type Reset reserved TBPWML Type Reset RO 0 R/W 0 reserved RO 0 RO 0 TBEVENT R/W 0 R/W 0 reserved TAPWML reserved RO 0 R/W 0 RO 0 RTCEN R/W 0 TAEVENT R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:15 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 14 TBPWML R/W 0 GPTM TimerB PWM Output Level The TBPWML values are defined as follows: Value Description 13:12 reserved RO 0 11:10 TBEVENT R/W 0x0 0 Output is unaffected. 1 Output is inverted. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. GPTM TimerB Event Mode The TBEVENT values are defined as follows: Value Description 0x0 Positive edge 0x1 Negative edge 0x2 Reserved 0x3 Both edges 280 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 9 TBSTALL R/W 0 Description GPTM Timer B Stall Enable The TBSTALL values are defined as follows: Value Description 0 Timer B continues counting while the processor is halted by the debugger. 1 Timer B freezes counting while the processor is halted by the debugger. If the processor is executing normally, the TBSTALL bit is ignored. 8 TBEN R/W 0 GPTM TimerB Enable The TBEN values are defined as follows: Value Description 0 TimerB is disabled. 1 TimerB is enabled and begins counting or the capture logic is enabled based on the GPTMCFG register. 7 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 TAPWML R/W 0 GPTM TimerA PWM Output Level The TAPWML values are defined as follows: Value Description 0 Output is unaffected. 1 Output is inverted. 5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 RTCEN R/W 0 GPTM RTC Enable The RTCEN values are defined as follows: Value Description 3:2 TAEVENT R/W 0x0 0 RTC counting is disabled. 1 RTC counting is enabled. GPTM TimerA Event Mode The TAEVENT values are defined as follows: Value Description 0x0 Positive edge 0x1 Negative edge 0x2 Reserved 0x3 Both edges July 14, 2014 281 Texas Instruments-Production Data General-Purpose Timers Bit/Field Name Type Reset 1 TASTALL R/W 0 Description GPTM Timer A Stall Enable The TASTALL values are defined as follows: Value Description 0 Timer A continues counting while the processor is halted by the debugger. 1 Timer A freezes counting while the processor is halted by the debugger. If the processor is executing normally, the TASTALL bit is ignored. 0 TAEN R/W 0 GPTM TimerA Enable The TAEN values are defined as follows: Value Description 0 TimerA is disabled. 1 TimerA is enabled and begins counting or the capture logic is enabled based on the GPTMCFG register. 282 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: GPTM Interrupt Mask (GPTMIMR), offset 0x018 This register allows software to enable/disable GPTM controller-level interrupts. Writing a 1 enables the interrupt, while writing a 0 disables it. GPTM Interrupt Mask (GPTMIMR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x018 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 CBEIM CBMIM TBTOIM RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RTCIM CAEIM CAMIM TATOIM RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 reserved Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 CBEIM R/W 0 GPTM CaptureB Event Interrupt Mask The CBEIM values are defined as follows: Value Description 9 CBMIM R/W 0 0 Interrupt is disabled. 1 Interrupt is enabled. GPTM CaptureB Match Interrupt Mask The CBMIM values are defined as follows: Value Description 8 TBTOIM R/W 0 0 Interrupt is disabled. 1 Interrupt is enabled. GPTM TimerB Time-Out Interrupt Mask The TBTOIM values are defined as follows: Value Description 7:4 reserved RO 0 0 Interrupt is disabled. 1 Interrupt is enabled. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 283 Texas Instruments-Production Data General-Purpose Timers Bit/Field Name Type Reset 3 RTCIM R/W 0 Description GPTM RTC Interrupt Mask The RTCIM values are defined as follows: Value Description 2 CAEIM R/W 0 0 Interrupt is disabled. 1 Interrupt is enabled. GPTM CaptureA Event Interrupt Mask The CAEIM values are defined as follows: Value Description 1 CAMIM R/W 0 0 Interrupt is disabled. 1 Interrupt is enabled. GPTM CaptureA Match Interrupt Mask The CAMIM values are defined as follows: Value Description 0 TATOIM R/W 0 0 Interrupt is disabled. 1 Interrupt is enabled. GPTM TimerA Time-Out Interrupt Mask The TATOIM values are defined as follows: Value Description 0 Interrupt is disabled. 1 Interrupt is enabled. 284 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 6: GPTM Raw Interrupt Status (GPTMRIS), offset 0x01C This register shows the state of the GPTM's internal interrupt signal. These bits are set whether or not the interrupt is masked in the GPTMIMR register. Each bit can be cleared by writing a 1 to its corresponding bit in GPTMICR. GPTM Raw Interrupt Status (GPTMRIS) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x01C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RTCRIS CAERIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 CBERIS RO 0 CBMRIS TBTORIS RO 0 RO 0 reserved CAMRIS TATORIS RO 0 RO 0 Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 CBERIS RO 0 GPTM CaptureB Event Raw Interrupt This is the CaptureB Event interrupt status prior to masking. 9 CBMRIS RO 0 GPTM CaptureB Match Raw Interrupt This is the CaptureB Match interrupt status prior to masking. 8 TBTORIS RO 0 GPTM TimerB Time-Out Raw Interrupt This is the TimerB time-out interrupt status prior to masking. 7:4 reserved RO 0x0 3 RTCRIS RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. GPTM RTC Raw Interrupt This is the RTC Event interrupt status prior to masking. 2 CAERIS RO 0 GPTM CaptureA Event Raw Interrupt This is the CaptureA Event interrupt status prior to masking. 1 CAMRIS RO 0 GPTM CaptureA Match Raw Interrupt This is the CaptureA Match interrupt status prior to masking. 0 TATORIS RO 0 GPTM TimerA Time-Out Raw Interrupt This the TimerA time-out interrupt status prior to masking. July 14, 2014 285 Texas Instruments-Production Data General-Purpose Timers Register 7: GPTM Masked Interrupt Status (GPTMMIS), offset 0x020 This register show the state of the GPTM's controller-level interrupt. If an interrupt is unmasked in GPTMIMR, and there is an event that causes the interrupt to be asserted, the corresponding bit is set in this register. All bits are cleared by writing a 1 to the corresponding bit in GPTMICR. GPTM Masked Interrupt Status (GPTMMIS) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x020 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 CBEMIS CBMMIS TBTOMIS RO 0 RO 0 RO 0 reserved RTCMIS RO 0 CAEMIS CAMMIS TATOMIS RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 CBEMIS RO 0 GPTM CaptureB Event Masked Interrupt This is the CaptureB event interrupt status after masking. 9 CBMMIS RO 0 GPTM CaptureB Match Masked Interrupt This is the CaptureB match interrupt status after masking. 8 TBTOMIS RO 0 GPTM TimerB Time-Out Masked Interrupt This is the TimerB time-out interrupt status after masking. 7:4 reserved RO 0x0 3 RTCMIS RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. GPTM RTC Masked Interrupt This is the RTC event interrupt status after masking. 2 CAEMIS RO 0 GPTM CaptureA Event Masked Interrupt This is the CaptureA event interrupt status after masking. 1 CAMMIS RO 0 GPTM CaptureA Match Masked Interrupt This is the CaptureA match interrupt status after masking. 0 TATOMIS RO 0 GPTM TimerA Time-Out Masked Interrupt This is the TimerA time-out interrupt status after masking. 286 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: GPTM Interrupt Clear (GPTMICR), offset 0x024 This register is used to clear the status bits in the GPTMRIS and GPTMMIS registers. Writing a 1 to a bit clears the corresponding bit in the GPTMRIS and GPTMMIS registers. GPTM Interrupt Clear (GPTMICR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x024 Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 reserved Type Reset reserved Type Reset RO 0 RO 0 RO 0 CBECINT CBMCINT RO 0 RO 0 W1C 0 W1C 0 reserved TBTOCINT W1C 0 RO 0 RO 0 RO 0 RTCCINT CAECINT CAMCINT RO 0 W1C 0 W1C 0 W1C 0 0 TATOCINT W1C 0 Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 CBECINT W1C 0 GPTM CaptureB Event Interrupt Clear The CBECINT values are defined as follows: Value Description 9 CBMCINT W1C 0 0 The interrupt is unaffected. 1 The interrupt is cleared. GPTM CaptureB Match Interrupt Clear The CBMCINT values are defined as follows: Value Description 8 TBTOCINT W1C 0 0 The interrupt is unaffected. 1 The interrupt is cleared. GPTM TimerB Time-Out Interrupt Clear The TBTOCINT values are defined as follows: Value Description 7:4 reserved RO 0x0 0 The interrupt is unaffected. 1 The interrupt is cleared. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 287 Texas Instruments-Production Data General-Purpose Timers Bit/Field Name Type Reset 3 RTCCINT W1C 0 Description GPTM RTC Interrupt Clear The RTCCINT values are defined as follows: Value Description 2 CAECINT W1C 0 0 The interrupt is unaffected. 1 The interrupt is cleared. GPTM CaptureA Event Interrupt Clear The CAECINT values are defined as follows: Value Description 1 CAMCINT W1C 0 0 The interrupt is unaffected. 1 The interrupt is cleared. GPTM CaptureA Match Interrupt Clear The CAMCINT values are defined as follows: Value Description 0 TATOCINT W1C 0 0 The interrupt is unaffected. 1 The interrupt is cleared. GPTM TimerA Time-Out Interrupt Clear The TATOCINT values are defined as follows: Value Description 0 The interrupt is unaffected. 1 The interrupt is cleared. 288 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 9: GPTM TimerA Interval Load (GPTMTAILR), offset 0x028 This register is used to load the starting count value into the timer. When GPTM is configured to one of the 32-bit modes, GPTMTAILR appears as a 32-bit register (the upper 16-bits correspond to the contents of the GPTM TimerB Interval Load (GPTMTBILR) register). In 16-bit mode, the upper 16 bits of this register read as 0s and have no effect on the state of GPTMTBILR. GPTM TimerA Interval Load (GPTMTAILR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x028 Type R/W, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 TAILRH Type Reset TAILRL Type Reset Bit/Field Name Type Reset 31:16 TAILRH R/W 0xFFFF Description GPTM TimerA Interval Load Register High When configured for 32-bit mode via the GPTMCFG register, the GPTM TimerB Interval Load (GPTMTBILR) register loads this value on a write. A read returns the current value of GPTMTBILR. In 16-bit mode, this field reads as 0 and does not have an effect on the state of GPTMTBILR. 15:0 TAILRL R/W 0xFFFF GPTM TimerA Interval Load Register Low For both 16- and 32-bit modes, writing this field loads the counter for TimerA. A read returns the current value of GPTMTAILR. July 14, 2014 289 Texas Instruments-Production Data General-Purpose Timers Register 10: GPTM TimerB Interval Load (GPTMTBILR), offset 0x02C This register is used to load the starting count value into TimerB. When the GPTM is configured to a 32-bit mode, GPTMTBILR returns the current value of TimerB and ignores writes. GPTM TimerB Interval Load (GPTMTBILR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x02C Type R/W, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset TBILRL Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TBILRL R/W 0xFFFF GPTM TimerB Interval Load Register When the GPTM is not configured as a 32-bit timer, a write to this field updates GPTMTBILR. In 32-bit mode, writes are ignored, and reads return the current value of GPTMTBILR. 290 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 11: GPTM TimerA Match (GPTMTAMATCHR), offset 0x030 This register is used in 32-bit Real-Time Clock mode and 16-bit PWM and Input Edge Count modes. GPTM TimerA Match (GPTMTAMATCHR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x030 Type R/W, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 TAMRH Type Reset TAMRL Type Reset Bit/Field Name Type Reset 31:16 TAMRH R/W 0xFFFF Description GPTM TimerA Match Register High When configured for 32-bit Real-Time Clock (RTC) mode via the GPTMCFG register, this value is compared to the upper half of GPTMTAR, to determine match events. In 16-bit mode, this field reads as 0 and does not have an effect on the state of GPTMTBMATCHR. 15:0 TAMRL R/W 0xFFFF GPTM TimerA Match Register Low When configured for 32-bit Real-Time Clock (RTC) mode via the GPTMCFG register, this value is compared to the lower half of GPTMTAR, to determine match events. When configured for PWM mode, this value along with GPTMTAILR, determines the duty cycle of the output PWM signal. When configured for Edge Count mode, this value along with GPTMTAILR, determines how many edge events are counted. The total number of edge events counted is equal to the value in GPTMTAILR minus this value. July 14, 2014 291 Texas Instruments-Production Data General-Purpose Timers Register 12: GPTM TimerB Match (GPTMTBMATCHR), offset 0x034 This register is used in 16-bit PWM and Input Edge Count modes. GPTM TimerB Match (GPTMTBMATCHR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x034 Type R/W, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 reserved Type Reset TBMRL Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TBMRL R/W 0xFFFF GPTM TimerB Match Register Low When configured for PWM mode, this value along with GPTMTBILR, determines the duty cycle of the output PWM signal. When configured for Edge Count mode, this value along with GPTMTBILR, determines how many edge events are counted. The total number of edge events counted is equal to the value in GPTMTBILR minus this value. 292 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 13: GPTM TimerA Prescale (GPTMTAPR), offset 0x038 This register allows software to extend the range of the 16-bit timers when operating in one-shot or periodic mode. GPTM TimerA Prescale (GPTMTAPR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x038 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TAPSR RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 TAPSR R/W 0x00 GPTM TimerA Prescale The register loads this value on a write. A read returns the current value of the register. Refer to Table 8-3 on page 267 for more details and an example. July 14, 2014 293 Texas Instruments-Production Data General-Purpose Timers Register 14: GPTM TimerB Prescale (GPTMTBPR), offset 0x03C This register allows software to extend the range of the 16-bit timers when operating in one-shot or periodic mode. GPTM TimerB Prescale (GPTMTBPR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x03C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TBPSR RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 TBPSR R/W 0x00 GPTM TimerB Prescale The register loads this value on a write. A read returns the current value of this register. Refer to Table 8-3 on page 267 for more details and an example. 294 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 15: GPTM TimerA Prescale Match (GPTMTAPMR), offset 0x040 This register effectively extends the range of GPTMTAMATCHR to 24 bits when operating in 16-bit one-shot or periodic mode. GPTM TimerA Prescale Match (GPTMTAPMR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x040 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TAPSMR RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 TAPSMR R/W 0x00 GPTM TimerA Prescale Match This value is used alongside GPTMTAMATCHR to detect timer match events while using a prescaler. July 14, 2014 295 Texas Instruments-Production Data General-Purpose Timers Register 16: GPTM TimerB Prescale Match (GPTMTBPMR), offset 0x044 This register effectively extends the range of GPTMTBMATCHR to 24 bits when operating in 16-bit one-shot or periodic mode. GPTM TimerB Prescale Match (GPTMTBPMR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x044 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset TBPSMR RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 TBPSMR R/W 0x00 GPTM TimerB Prescale Match This value is used alongside GPTMTBMATCHR to detect timer match events while using a prescaler. 296 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: GPTM TimerA (GPTMTAR), offset 0x048 This register shows the current value of the TimerA counter in all cases except for Input Edge Count mode. When in this mode, this register contains the number of edges that have occurred. GPTM TimerA (GPTMTAR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x048 Type RO, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 TARH Type Reset TARL Type Reset Bit/Field Name Type Reset 31:16 TARH RO 0xFFFF Description GPTM TimerA Register High If the GPTMCFG is in a 32-bit mode, TimerB value is read. If the GPTMCFG is in a 16-bit mode, this is read as zero. 15:0 TARL RO 0xFFFF GPTM TimerA Register Low A read returns the current value of the GPTM TimerA Count Register, except in Input Edge-Count mode, when it returns the number of edges that have occurred. July 14, 2014 297 Texas Instruments-Production Data General-Purpose Timers Register 18: GPTM TimerB (GPTMTBR), offset 0x04C This register shows the current value of the TimerB counter in all cases except for Input Edge Count mode. When in this mode, this register contains the number of edges that have occurred. GPTM TimerB (GPTMTBR) Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 Offset 0x04C Type RO, reset 0x0000.FFFF 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 reserved Type Reset TBRL Type Reset Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 TBRL RO 0xFFFF GPTM TimerB A read returns the current value of the GPTM TimerB Count Register, except in Input Edge-Count mode, when it returns the number of edges that have occurred. 298 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 9 Watchdog Timer A watchdog timer can generate nonmaskable interrupts (NMIs) or a reset when a time-out value is reached. The watchdog timer is used to regain control when a system has failed due to a software error or due to the failure of an external device to respond in the expected way. ® The Stellaris Watchdog Timer module has the following features: ■ 32-bit down counter with a programmable load register ■ Separate watchdog clock with an enable ■ Programmable interrupt generation logic with interrupt masking ■ Lock register protection from runaway software ■ Reset generation logic with an enable/disable ■ User-enabled stalling when the controller asserts the CPU Halt flag during debug The Watchdog Timer can be configured to generate an interrupt to the controller on its first time-out, and to generate a reset signal on its second time-out. Once the Watchdog Timer has been configured, the lock register can be written to prevent the timer configuration from being inadvertently altered. July 14, 2014 299 Texas Instruments-Production Data Watchdog Timer 9.1 Block Diagram Figure 9-1. WDT Module Block Diagram WDTLOAD Control / Clock / Interrupt Generation WDTCTL WDTICR Interrupt WDTRIS 32-Bit Down Counter WDTMIS 0x00000000 WDTLOCK System Clock WDTTEST Comparator WDTVALUE Identification Registers 9.2 WDTPCellID0 WDTPeriphID0 WDTPeriphID4 WDTPCellID1 WDTPeriphID1 WDTPeriphID5 WDTPCellID2 WDTPeriphID2 WDTPeriphID6 WDTPCellID3 WDTPeriphID3 WDTPeriphID7 Functional Description The Watchdog Timer module generates the first time-out signal when the 32-bit counter reaches the zero state after being enabled; enabling the counter also enables the watchdog timer interrupt. After the first time-out event, the 32-bit counter is re-loaded with the value of the Watchdog Timer Load (WDTLOAD) register, and the timer resumes counting down from that value. Once the Watchdog Timer has been configured, the Watchdog Timer Lock (WDTLOCK) register is written, which prevents the timer configuration from being inadvertently altered by software. If the timer counts down to its zero state again before the first time-out interrupt is cleared, and the reset signal has been enabled (via the WatchdogResetEnable function), the Watchdog timer asserts its reset signal to the system. If the interrupt is cleared before the 32-bit counter reaches its second time-out, the 32-bit counter is loaded with the value in the WDTLOAD register, and counting resumes from that value. If WDTLOAD is written with a new value while the Watchdog Timer counter is counting, then the counter is loaded with the new value and continues counting. 300 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Writing to WDTLOAD does not clear an active interrupt. An interrupt must be specifically cleared by writing to the Watchdog Interrupt Clear (WDTICR) register. The Watchdog module interrupt and reset generation can be enabled or disabled as required. When the interrupt is re-enabled, the 32-bit counter is preloaded with the load register value and not its last state. 9.3 Initialization and Configuration To use the WDT, its peripheral clock must be enabled by setting the WDT bit in the RCGC0 register. The Watchdog Timer is configured using the following sequence: 1. Load the WDTLOAD register with the desired timer load value. 2. If the Watchdog is configured to trigger system resets, set the RESEN bit in the WDTCTL register. 3. Set the INTEN bit in the WDTCTL register to enable the Watchdog and lock the control register. If software requires that all of the watchdog registers are locked, the Watchdog Timer module can be fully locked by writing any value to the WDTLOCK register. To unlock the Watchdog Timer, write a value of 0x1ACC.E551. 9.4 Register Map Table 9-1 on page 301 lists the Watchdog registers. The offset listed is a hexadecimal increment to the register’s address, relative to the Watchdog Timer base address of 0x4000.0000. Table 9-1. Watchdog Timer Register Map Description See page Offset Name Type Reset 0x000 WDTLOAD R/W 0xFFFF.FFFF Watchdog Load 303 0x004 WDTVALUE RO 0xFFFF.FFFF Watchdog Value 304 0x008 WDTCTL R/W 0x0000.0000 Watchdog Control 305 0x00C WDTICR WO - Watchdog Interrupt Clear 306 0x010 WDTRIS RO 0x0000.0000 Watchdog Raw Interrupt Status 307 0x014 WDTMIS RO 0x0000.0000 Watchdog Masked Interrupt Status 308 0x418 WDTTEST R/W 0x0000.0000 Watchdog Test 309 0xC00 WDTLOCK R/W 0x0000.0000 Watchdog Lock 310 0xFD0 WDTPeriphID4 RO 0x0000.0000 Watchdog Peripheral Identification 4 311 0xFD4 WDTPeriphID5 RO 0x0000.0000 Watchdog Peripheral Identification 5 312 0xFD8 WDTPeriphID6 RO 0x0000.0000 Watchdog Peripheral Identification 6 313 0xFDC WDTPeriphID7 RO 0x0000.0000 Watchdog Peripheral Identification 7 314 0xFE0 WDTPeriphID0 RO 0x0000.0005 Watchdog Peripheral Identification 0 315 0xFE4 WDTPeriphID1 RO 0x0000.0018 Watchdog Peripheral Identification 1 316 0xFE8 WDTPeriphID2 RO 0x0000.0018 Watchdog Peripheral Identification 2 317 July 14, 2014 301 Texas Instruments-Production Data Watchdog Timer Table 9-1. Watchdog Timer Register Map (continued) Offset Name 0xFEC Reset WDTPeriphID3 RO 0x0000.0001 Watchdog Peripheral Identification 3 318 0xFF0 WDTPCellID0 RO 0x0000.000D Watchdog PrimeCell Identification 0 319 0xFF4 WDTPCellID1 RO 0x0000.00F0 Watchdog PrimeCell Identification 1 320 0xFF8 WDTPCellID2 RO 0x0000.0005 Watchdog PrimeCell Identification 2 321 0xFFC WDTPCellID3 RO 0x0000.00B1 Watchdog PrimeCell Identification 3 322 9.5 Description See page Type Register Descriptions The remainder of this section lists and describes the WDT registers, in numerical order by address offset. 302 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 1: Watchdog Load (WDTLOAD), offset 0x000 This register is the 32-bit interval value used by the 32-bit counter. When this register is written, the value is immediately loaded and the counter restarts counting down from the new value. If the WDTLOAD register is loaded with 0x0000.0000, an interrupt is immediately generated. Watchdog Load (WDTLOAD) Base 0x4000.0000 Offset 0x000 Type R/W, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 15 14 13 12 11 10 9 8 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 23 22 21 20 19 18 17 16 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 7 6 5 4 3 2 1 0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 WDTLoad Type Reset WDTLoad Type Reset Bit/Field Name Type 31:0 WDTLoad R/W Reset R/W 1 Description 0xFFFF.FFFF Watchdog Load Value July 14, 2014 303 Texas Instruments-Production Data Watchdog Timer Register 2: Watchdog Value (WDTVALUE), offset 0x004 This register contains the current count value of the timer. Watchdog Value (WDTVALUE) Base 0x4000.0000 Offset 0x004 Type RO, reset 0xFFFF.FFFF 31 30 29 28 27 26 25 24 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 15 14 13 12 11 10 9 8 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 23 22 21 20 19 18 17 16 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 7 6 5 4 3 2 1 0 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 RO 1 WDTValue Type Reset WDTValue Type Reset Bit/Field Name Type 31:0 WDTValue RO Reset RO 1 Description 0xFFFF.FFFF Watchdog Value Current value of the 32-bit down counter. 304 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 3: Watchdog Control (WDTCTL), offset 0x008 This register is the watchdog control register. The watchdog timer can be configured to generate a reset signal (on second time-out) or an interrupt on time-out. When the watchdog interrupt has been enabled, all subsequent writes to the control register are ignored. The only mechanism that can re-enable writes is a hardware reset. Watchdog Control (WDTCTL) Base 0x4000.0000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 1 0 RESEN INTEN R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:2 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 RESEN R/W 0 Watchdog Reset Enable The RESEN values are defined as follows: Value Description 0 INTEN R/W 0 0 Disabled. 1 Enable the Watchdog module reset output. Watchdog Interrupt Enable The INTEN values are defined as follows: Value Description 0 Interrupt event disabled (once this bit is set, it can only be cleared by a hardware reset). 1 Interrupt event enabled. Once enabled, all writes are ignored. July 14, 2014 305 Texas Instruments-Production Data Watchdog Timer Register 4: Watchdog Interrupt Clear (WDTICR), offset 0x00C This register is the interrupt clear register. A write of any value to this register clears the Watchdog interrupt and reloads the 32-bit counter from the WDTLOAD register. Value for a read or reset is indeterminate. Watchdog Interrupt Clear (WDTICR) Base 0x4000.0000 Offset 0x00C Type WO, reset 31 30 29 28 27 26 25 24 WO - WO - WO - WO - WO - WO - WO - WO - 15 14 13 12 11 10 9 8 WO - WO - WO - WO - WO - WO - WO - WO - 23 22 21 20 19 18 17 16 WO - WO - WO - WO - WO - WO - WO - WO - 7 6 5 4 3 2 1 0 WO - WO - WO - WO - WO - WO - WO - WDTIntClr Type Reset WDTIntClr Type Reset Bit/Field Name Type Reset 31:0 WDTIntClr WO - WO - Description Watchdog Interrupt Clear 306 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: Watchdog Raw Interrupt Status (WDTRIS), offset 0x010 This register is the raw interrupt status register. Watchdog interrupt events can be monitored via this register if the controller interrupt is masked. Watchdog Raw Interrupt Status (WDTRIS) Base 0x4000.0000 Offset 0x010 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 WDTRIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 WDTRIS RO 0 Watchdog Raw Interrupt Status Gives the raw interrupt state (prior to masking) of WDTINTR. July 14, 2014 307 Texas Instruments-Production Data Watchdog Timer Register 6: Watchdog Masked Interrupt Status (WDTMIS), offset 0x014 This register is the masked interrupt status register. The value of this register is the logical AND of the raw interrupt bit and the Watchdog interrupt enable bit. Watchdog Masked Interrupt Status (WDTMIS) Base 0x4000.0000 Offset 0x014 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 WDTMIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 WDTMIS RO 0 Watchdog Masked Interrupt Status Gives the masked interrupt state (after masking) of the WDTINTR interrupt. 308 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 7: Watchdog Test (WDTTEST), offset 0x418 This register provides user-enabled stalling when the microcontroller asserts the CPU halt flag during debug. Watchdog Test (WDTTEST) Base 0x4000.0000 Offset 0x418 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 STALL R/W 0 reserved Bit/Field Name Type Reset Description 31:9 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 8 STALL R/W 0 Watchdog Stall Enable When set to 1, if the Stellaris microcontroller is stopped with a debugger, the watchdog timer stops counting. Once the microcontroller is restarted, the watchdog timer resumes counting. 7:0 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 309 Texas Instruments-Production Data Watchdog Timer Register 8: Watchdog Lock (WDTLOCK), offset 0xC00 Writing 0x1ACC.E551 to the WDTLOCK register enables write access to all other registers. Writing any other value to the WDTLOCK register re-enables the locked state for register writes to all the other registers. Reading the WDTLOCK register returns the lock status rather than the 32-bit value written. Therefore, when write accesses are disabled, reading the WDTLOCK register returns 0x0000.0001 (when locked; otherwise, the returned value is 0x0000.0000 (unlocked)). Watchdog Lock (WDTLOCK) Base 0x4000.0000 Offset 0xC00 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 WDTLock Type Reset WDTLock Type Reset Bit/Field Name Type Reset 31:0 WDTLock R/W 0x0000 R/W 0 Description Watchdog Lock A write of the value 0x1ACC.E551 unlocks the watchdog registers for write access. A write of any other value reapplies the lock, preventing any register updates. A read of this register returns the following values: Value Description 0x0000.0001 Locked 0x0000.0000 Unlocked 310 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 9: Watchdog Peripheral Identification 4 (WDTPeriphID4), offset 0xFD0 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 4 (WDTPeriphID4) Base 0x4000.0000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID4 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID4 RO 0x00 WDT Peripheral ID Register[7:0] July 14, 2014 311 Texas Instruments-Production Data Watchdog Timer Register 10: Watchdog Peripheral Identification 5 (WDTPeriphID5), offset 0xFD4 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 5 (WDTPeriphID5) Base 0x4000.0000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID5 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID5 RO 0x00 WDT Peripheral ID Register[15:8] 312 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 11: Watchdog Peripheral Identification 6 (WDTPeriphID6), offset 0xFD8 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 6 (WDTPeriphID6) Base 0x4000.0000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID6 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID6 RO 0x00 WDT Peripheral ID Register[23:16] July 14, 2014 313 Texas Instruments-Production Data Watchdog Timer Register 12: Watchdog Peripheral Identification 7 (WDTPeriphID7), offset 0xFDC The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 7 (WDTPeriphID7) Base 0x4000.0000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID7 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID7 RO 0x00 WDT Peripheral ID Register[31:24] 314 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 13: Watchdog Peripheral Identification 0 (WDTPeriphID0), offset 0xFE0 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 0 (WDTPeriphID0) Base 0x4000.0000 Offset 0xFE0 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID0 RO 0x05 Watchdog Peripheral ID Register[7:0] July 14, 2014 315 Texas Instruments-Production Data Watchdog Timer Register 14: Watchdog Peripheral Identification 1 (WDTPeriphID1), offset 0xFE4 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 1 (WDTPeriphID1) Base 0x4000.0000 Offset 0xFE4 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID1 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID1 RO 0x18 Watchdog Peripheral ID Register[15:8] 316 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 15: Watchdog Peripheral Identification 2 (WDTPeriphID2), offset 0xFE8 The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 2 (WDTPeriphID2) Base 0x4000.0000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID2 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID2 RO 0x18 Watchdog Peripheral ID Register[23:16] July 14, 2014 317 Texas Instruments-Production Data Watchdog Timer Register 16: Watchdog Peripheral Identification 3 (WDTPeriphID3), offset 0xFEC The WDTPeriphIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog Peripheral Identification 3 (WDTPeriphID3) Base 0x4000.0000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 PID3 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID3 RO 0x01 Watchdog Peripheral ID Register[31:24] 318 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: Watchdog PrimeCell Identification 0 (WDTPCellID0), offset 0xFF0 The WDTPCellIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog PrimeCell Identification 0 (WDTPCellID0) Base 0x4000.0000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID0 RO 0x0D Watchdog PrimeCell ID Register[7:0] July 14, 2014 319 Texas Instruments-Production Data Watchdog Timer Register 18: Watchdog PrimeCell Identification 1 (WDTPCellID1), offset 0xFF4 The WDTPCellIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog PrimeCell Identification 1 (WDTPCellID1) Base 0x4000.0000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 1 RO 1 RO 1 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset CID1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID1 RO 0xF0 Watchdog PrimeCell ID Register[15:8] 320 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 19: Watchdog PrimeCell Identification 2 (WDTPCellID2), offset 0xFF8 The WDTPCellIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog PrimeCell Identification 2 (WDTPCellID2) Base 0x4000.0000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID2 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID2 RO 0x05 Watchdog PrimeCell ID Register[23:16] July 14, 2014 321 Texas Instruments-Production Data Watchdog Timer Register 20: Watchdog PrimeCell Identification 3 (WDTPCellID3 ), offset 0xFFC The WDTPCellIDn registers are hard-coded and the fields within the register determine the reset value. Watchdog PrimeCell Identification 3 (WDTPCellID3) Base 0x4000.0000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 0 RO 1 RO 1 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset CID3 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID3 RO 0xB1 Watchdog PrimeCell ID Register[31:24] 322 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 10 Universal Asynchronous Receivers/Transmitters (UARTs) ® Each Stellaris Universal Asynchronous Receiver/Transmitter (UART) has the following features: ■ Two fully programmable 16C550-type UARTs ■ Separate 16x8 transmit (TX) and receive (RX) FIFOs to reduce CPU interrupt service loading ■ Programmable baud-rate generator allowing speeds up to 3.125 Mbps ■ Programmable FIFO length, including 1-byte deep operation providing conventional double-buffered interface ■ FIFO trigger levels of 1/8, 1/4, 1/2, 3/4, and 7/8 ■ Standard asynchronous communication bits for start, stop, and parity ■ Line-break generation and detection ■ Fully programmable serial interface characteristics – 5, 6, 7, or 8 data bits – Even, odd, stick, or no-parity bit generation/detection – 1 or 2 stop bit generation July 14, 2014 323 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) 10.1 Block Diagram Figure 10-1. UART Module Block Diagram System Clock Interrupt Interrupt Control UARTIFLS UARTIM UARTMIS UARTRIS UARTICR Identification Registers UARTPCellID0 UARTPCellID1 UARTPCellID2 UARTPCellID3 UARTPeriphID0 UARTPeriphID1 UARTPeriphID2 UARTPeriphID3 UARTPeriphID4 UARTPeriphID5 UARTPeriphID6 UARTPeriphID7 10.2 TxFIFO 16 x 8 . . . Transmitter UnTx Baud Rate Generator UARTIBRD UARTFBRD UARTDR Receiver Control/Status UnRx RxFIFO 16 x 8 UARTRSR/ECR UARTFR UARTLCRH UARTCTL UARTILPR . . . Signal Description Table 10-1 on page 324 lists the external signals of the UART module and describes the function of each. The UART signals are alternate functions for some GPIO signals and default to be GPIO signals at reset, with the exception of the U0Rx and U0Tx pins which default to the UART function. The column in the table below titled "Pin Assignment" lists the possible GPIO pin placements for these UART signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the UART function. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 10-1. UART Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type U0Rx 17 I TTL Description UART module 0 receive. U0Tx 18 O TTL UART module 0 transmit. U1Rx 27 I TTL UART module 1 receive. U1Tx 28 O TTL UART module 1 transmit. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 324 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 10.3 Functional Description Each Stellaris UART performs the functions of parallel-to-serial and serial-to-parallel conversions. It is similar in functionality to a 16C550 UART, but is not register compatible. The UART is configured for transmit and/or receive via the TXE and RXE bits of the UART Control (UARTCTL) register (see page 341). Transmit and receive are both enabled out of reset. Before any control registers are programmed, the UART must be disabled by clearing the UARTEN bit in UARTCTL. If the UART is disabled during a TX or RX operation, the current transaction is completed prior to the UART stopping. 10.3.1 Transmit/Receive Logic The transmit logic performs parallel-to-serial conversion on the data read from the transmit FIFO. The control logic outputs the serial bit stream beginning with a start bit, and followed by the data bits (LSB first), parity bit, and the stop bits according to the programmed configuration in the control registers. See Figure 10-2 on page 325 for details. The receive logic performs serial-to-parallel conversion on the received bit stream after a valid start pulse has been detected. Overrun, parity, frame error checking, and line-break detection are also performed, and their status accompanies the data that is written to the receive FIFO. Figure 10-2. UART Character Frame UnTX LSB 1 5-8 data bits 0 n Parity bit if enabled Start 10.3.2 1-2 stop bits MSB Baud-Rate Generation The baud-rate divisor is a 22-bit number consisting of a 16-bit integer and a 6-bit fractional part. The number formed by these two values is used by the baud-rate generator to determine the bit period. Having a fractional baud-rate divider allows the UART to generate all the standard baud rates. The 16-bit integer is loaded through the UART Integer Baud-Rate Divisor (UARTIBRD) register (see page 337) and the 6-bit fractional part is loaded with the UART Fractional Baud-Rate Divisor (UARTFBRD) register (see page 338). The baud-rate divisor (BRD) has the following relationship to the system clock (where BRDI is the integer part of the BRD and BRDF is the fractional part, separated by a decimal place.) BRD = BRDI + BRDF = UARTSysClk / (16 * Baud Rate) where UARTSysClk is the system clock connected to the UART. The 6-bit fractional number (that is to be loaded into the DIVFRAC bit field in the UARTFBRD register) can be calculated by taking the fractional part of the baud-rate divisor, multiplying it by 64, and adding 0.5 to account for rounding errors: UARTFBRD[DIVFRAC] = integer(BRDF * 64 + 0.5) The UART generates an internal baud-rate reference clock at 16x the baud-rate (referred to as Baud16). This reference clock is divided by 16 to generate the transmit clock, and is used for error detection during receive operations. July 14, 2014 325 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Along with the UART Line Control, High Byte (UARTLCRH) register (see page 339), the UARTIBRD and UARTFBRD registers form an internal 30-bit register. This internal register is only updated when a write operation to UARTLCRH is performed, so any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register for the changes to take effect. To update the baud-rate registers, there are four possible sequences: ■ UARTIBRD write, UARTFBRD write, and UARTLCRH write ■ UARTFBRD write, UARTIBRD write, and UARTLCRH write ■ UARTIBRD write and UARTLCRH write ■ UARTFBRD write and UARTLCRH write 10.3.3 Data Transmission Data received or transmitted is stored in two 16-byte FIFOs, though the receive FIFO has an extra four bits per character for status information. For transmission, data is written into the transmit FIFO. If the UART is enabled, it causes a data frame to start transmitting with the parameters indicated in the UARTLCRH register. Data continues to be transmitted until there is no data left in the transmit FIFO. The BUSY bit in the UART Flag (UARTFR) register (see page 335) is asserted as soon as data is written to the transmit FIFO (that is, if the FIFO is non-empty) and remains asserted while data is being transmitted. The BUSY bit is negated only when the transmit FIFO is empty, and the last character has been transmitted from the shift register, including the stop bits. The UART can indicate that it is busy even though the UART may no longer be enabled. When the receiver is idle (the UnRx is continuously 1) and the data input goes Low (a start bit has been received), the receive counter begins running and data is sampled on the eighth cycle of Baud16 (described in “Transmit/Receive Logic” on page 325). The start bit is valid and recognized if UnRx is still low on the eighth cycle of Baud16, otherwise it is ignored. After a valid start bit is detected, successive data bits are sampled on every 16th cycle of Baud16 (that is, one bit period later) according to the programmed length of the data characters. The parity bit is then checked if parity mode was enabled. Data length and parity are defined in the UARTLCRH register. Lastly, a valid stop bit is confirmed if UnRx is High, otherwise a framing error has occurred. When a full word is received, the data is stored in the receive FIFO, with any error bits associated with that word. 10.3.4 FIFO Operation The UART has two 16-entry FIFOs; one for transmit and one for receive. Both FIFOs are accessed via the UART Data (UARTDR) register (see page 331). Read operations of the UARTDR register return a 12-bit value consisting of 8 data bits and 4 error flags while write operations place 8-bit data in the transmit FIFO. Out of reset, both FIFOs are disabled and act as 1-byte-deep holding registers. The FIFOs are enabled by setting the FEN bit in UARTLCRH (page 339). FIFO status can be monitored via the UART Flag (UARTFR) register (see page 335) and the UART Receive Status (UARTRSR) register. Hardware monitors empty, full and overrun conditions. The UARTFR register contains empty and full flags (TXFE, TXFF, RXFE, and RXFF bits) and the UARTRSR register shows overrun status via the OE bit. 326 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller The trigger points at which the FIFOs generate interrupts is controlled via the UART Interrupt FIFO Level Select (UARTIFLS) register (see page 343). Both FIFOs can be individually configured to trigger interrupts at different levels. Available configurations include 1/8, ¼, ½, ¾, and 7/8. For example, if the ¼ option is selected for the receive FIFO, the UART generates a receive interrupt after 4 data bytes are received. Out of reset, both FIFOs are configured to trigger an interrupt at the ½ mark. 10.3.5 Interrupts The UART can generate interrupts when the following conditions are observed: ■ Overrun Error ■ Break Error ■ Parity Error ■ Framing Error ■ Receive Timeout ■ Transmit (when condition defined in the TXIFLSEL bit in the UARTIFLS register is met) ■ Receive (when condition defined in the RXIFLSEL bit in the UARTIFLS register is met) All of the interrupt events are ORed together before being sent to the interrupt controller, so the UART can only generate a single interrupt request to the controller at any given time. Software can service multiple interrupt events in a single interrupt service routine by reading the UART Masked Interrupt Status (UARTMIS) register (see page 348). The interrupt events that can trigger a controller-level interrupt are defined in the UART Interrupt Mask (UARTIM ) register (see page 345) by setting the corresponding IM bit to 1. If interrupts are not used, the raw interrupt status is always visible via the UART Raw Interrupt Status (UARTRIS) register (see page 347). Interrupts are always cleared (for both the UARTMIS and UARTRIS registers) by setting the corresponding bit in the UART Interrupt Clear (UARTICR) register (see page 349). The receive interrupt changes state when one of the following events occurs: ■ If the FIFOs are enabled and the receive FIFO reaches the programmed trigger level, the RXRIS bit is set. The receive interrupt is cleared by reading data from the receive FIFO until it becomes less than the trigger level, or by clearing the interrupt by writing a 1 to the RXIC bit. ■ If the FIFOs are disabled (have a depth of one location) and data is received thereby filling the location, the RXRIS bit is set. The receive interrupt is cleared by performing a single read of the receive FIFO, or by clearing the interrupt by writing a 1 to the RXIC bit. The transmit interrupt changes state when one of the following events occurs: ■ If the FIFOs are enabled and the transmit FIFO progresses through the programmed trigger level, the TXRIS bit is set. The transmit interrupt is based on a transition through level, therefore the FIFO must be written past the programmed trigger level otherwise no further transmit interrupts will be generated. The transmit interrupt is cleared by writing data to the transmit FIFO until it becomes greater than the trigger level, or by clearing the interrupt by writing a 1 to the TXIC bit. July 14, 2014 327 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) ■ If the FIFOs are disabled (have a depth of one location) and there is no data present in the transmitters single location, the TXRIS bit is set. It is cleared by performing a single write to the transmit FIFO, or by clearing the interrupt by writing a 1 to the TXIC bit. 10.3.6 Loopback Operation The UART can be placed into an internal loopback mode for diagnostic or debug work. This is accomplished by setting the LBE bit in the UARTCTL register (see page 341). In loopback mode, data transmitted on UnTx is received on the UnRx input. 10.4 Initialization and Configuration To use the UARTs, the peripheral clock must be enabled by setting the UART0 or UART1 bits in the RCGC1 register. This section discusses the steps that are required to use a UART module. For this example, the UART clock is assumed to be 20 MHz and the desired UART configuration is: ■ 115200 baud rate ■ Data length of 8 bits ■ One stop bit ■ No parity ■ FIFOs disabled ■ No interrupts The first thing to consider when programming the UART is the baud-rate divisor (BRD), since the UARTIBRD and UARTFBRD registers must be written before the UARTLCRH register. Using the equation described in “Baud-Rate Generation” on page 325, the BRD can be calculated: BRD = 20,000,000 / (16 * 115,200) = 10.8507 which means that the DIVINT field of the UARTIBRD register (see page 337) should be set to 10. The value to be loaded into the UARTFBRD register (see page 338) is calculated by the equation: UARTFBRD[DIVFRAC] = integer(0.8507 * 64 + 0.5) = 54 With the BRD values in hand, the UART configuration is written to the module in the following order: 1. Disable the UART by clearing the UARTEN bit in the UARTCTL register. 2. Write the integer portion of the BRD to the UARTIBRD register. 3. Write the fractional portion of the BRD to the UARTFBRD register. 4. Write the desired serial parameters to the UARTLCRH register (in this case, a value of 0x0000.0060). 5. Enable the UART by setting the UARTEN bit in the UARTCTL register. 328 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 10.5 Register Map Table 10-2 on page 329 lists the UART registers. The offset listed is a hexadecimal increment to the register’s address, relative to that UART’s base address: ■ UART0: 0x4000.C000 ■ UART1: 0x4000.D000 Note that the UART module clock must be enabled before the registers can be programmed (see page 190). There must be a delay of 3 system clocks after the UART module clock is enabled before any UART module registers are accessed. Note: The UART must be disabled (see the UARTEN bit in the UARTCTL register on page 341) before any of the control registers are reprogrammed. When the UART is disabled during a TX or RX operation, the current transaction is completed prior to the UART stopping. Table 10-2. UART Register Map Offset Name Type Reset Description See page 0x000 UARTDR R/W 0x0000.0000 UART Data 331 0x004 UARTRSR/UARTECR R/W 0x0000.0000 UART Receive Status/Error Clear 333 0x018 UARTFR RO 0x0000.0090 UART Flag 335 0x024 UARTIBRD R/W 0x0000.0000 UART Integer Baud-Rate Divisor 337 0x028 UARTFBRD R/W 0x0000.0000 UART Fractional Baud-Rate Divisor 338 0x02C UARTLCRH R/W 0x0000.0000 UART Line Control 339 0x030 UARTCTL R/W 0x0000.0300 UART Control 341 0x034 UARTIFLS R/W 0x0000.0012 UART Interrupt FIFO Level Select 343 0x038 UARTIM R/W 0x0000.0000 UART Interrupt Mask 345 0x03C UARTRIS RO 0x0000.0000 UART Raw Interrupt Status 347 0x040 UARTMIS RO 0x0000.0000 UART Masked Interrupt Status 348 0x044 UARTICR W1C 0x0000.0000 UART Interrupt Clear 349 0xFD0 UARTPeriphID4 RO 0x0000.0000 UART Peripheral Identification 4 351 0xFD4 UARTPeriphID5 RO 0x0000.0000 UART Peripheral Identification 5 352 0xFD8 UARTPeriphID6 RO 0x0000.0000 UART Peripheral Identification 6 353 0xFDC UARTPeriphID7 RO 0x0000.0000 UART Peripheral Identification 7 354 0xFE0 UARTPeriphID0 RO 0x0000.0011 UART Peripheral Identification 0 355 0xFE4 UARTPeriphID1 RO 0x0000.0000 UART Peripheral Identification 1 356 0xFE8 UARTPeriphID2 RO 0x0000.0018 UART Peripheral Identification 2 357 0xFEC UARTPeriphID3 RO 0x0000.0001 UART Peripheral Identification 3 358 0xFF0 UARTPCellID0 RO 0x0000.000D UART PrimeCell Identification 0 359 0xFF4 UARTPCellID1 RO 0x0000.00F0 UART PrimeCell Identification 1 360 July 14, 2014 329 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Table 10-2. UART Register Map (continued) Offset Name 0xFF8 0xFFC 10.6 Description See page Type Reset UARTPCellID2 RO 0x0000.0005 UART PrimeCell Identification 2 361 UARTPCellID3 RO 0x0000.00B1 UART PrimeCell Identification 3 362 Register Descriptions The remainder of this section lists and describes the UART registers, in numerical order by address offset. 330 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 1: UART Data (UARTDR), offset 0x000 Important: This register is read-sensitive. See the register description for details. This register is the data register (the interface to the FIFOs). When FIFOs are enabled, data written to this location is pushed onto the transmit FIFO. If FIFOs are disabled, data is stored in the transmitter holding register (the bottom word of the transmit FIFO). A write to this register initiates a transmission from the UART. For received data, if the FIFO is enabled, the data byte and the 4-bit status (break, frame, parity, and overrun) is pushed onto the 12-bit wide receive FIFO. If FIFOs are disabled, the data byte and status are stored in the receiving holding register (the bottom word of the receive FIFO). The received data can be retrieved by reading this register. UART Data (UARTDR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 OE BE PE FE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 DATA Bit/Field Name Type Reset Description 31:12 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 11 OE RO 0 UART Overrun Error The OE values are defined as follows: Value Description 10 BE RO 0 0 There has been no data loss due to a FIFO overrun. 1 New data was received when the FIFO was full, resulting in data loss. UART Break Error This bit is set to 1 when a break condition is detected, indicating that the receive data input was held Low for longer than a full-word transmission time (defined as start, data, parity, and stop bits). In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the received data input goes to a 1 (marking state) and the next valid start bit is received. July 14, 2014 331 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 9 PE RO 0 Description UART Parity Error This bit is set to 1 when the parity of the received data character does not match the parity defined by bits 2 and 7 of the UARTLCRH register. In FIFO mode, this error is associated with the character at the top of the FIFO. 8 FE RO 0 UART Framing Error This bit is set to 1 when the received character does not have a valid stop bit (a valid stop bit is 1). 7:0 DATA R/W 0 Data Transmitted or Received When written, the data that is to be transmitted via the UART. When read, the data that was received by the UART. 332 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 2: UART Receive Status/Error Clear (UARTRSR/UARTECR), offset 0x004 The UARTRSR/UARTECR register is the receive status register/error clear register. In addition to the UARTDR register, receive status can also be read from the UARTRSR register. If the status is read from this register, then the status information corresponds to the entry read from UARTDR prior to reading UARTRSR. The status information for overrun is set immediately when an overrun condition occurs. The UARTRSR register cannot be written. A write of any value to the UARTECR register clears the framing, parity, break, and overrun errors. All the bits are cleared to 0 on reset. Reads UART Receive Status/Error Clear (UARTRSR/UARTECR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 OE BE PE FE RO 0 RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 OE RO 0 UART Overrun Error When this bit is set to 1, data is received and the FIFO is already full. This bit is cleared to 0 by a write to UARTECR. The FIFO contents remain valid since no further data is written when the FIFO is full, only the contents of the shift register are overwritten. The CPU must now read the data in order to empty the FIFO. 2 BE RO 0 UART Break Error This bit is set to 1 when a break condition is detected, indicating that the received data input was held Low for longer than a full-word transmission time (defined as start, data, parity, and stop bits). This bit is cleared to 0 by a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO. When a break occurs, only one 0 character is loaded into the FIFO. The next character is only enabled after the receive data input goes to a 1 (marking state) and the next valid start bit is received. July 14, 2014 333 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 1 PE RO 0 Description UART Parity Error This bit is set to 1 when the parity of the received data character does not match the parity defined by bits 2 and 7 of the UARTLCRH register. This bit is cleared to 0 by a write to UARTECR. 0 FE RO 0 UART Framing Error This bit is set to 1 when the received character does not have a valid stop bit (a valid stop bit is 1). This bit is cleared to 0 by a write to UARTECR. In FIFO mode, this error is associated with the character at the top of the FIFO. Writes UART Receive Status/Error Clear (UARTRSR/UARTECR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x004 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 15 14 13 12 11 10 9 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 23 22 21 20 19 18 17 16 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 8 7 6 5 4 3 2 1 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 reserved Type Reset reserved Type Reset DATA WO 0 Bit/Field Name Type Reset Description 31:8 reserved WO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DATA WO 0 Error Clear A write to this register of any data clears the framing, parity, break, and overrun flags. 334 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 3: UART Flag (UARTFR), offset 0x018 The UARTFR register is the flag register. After reset, the TXFF, RXFF, and BUSY bits are 0, and TXFE and RXFE bits are 1. UART Flag (UARTFR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x018 Type RO, reset 0x0000.0090 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 TXFE RXFF TXFF RXFE BUSY RO 1 RO 0 RO 0 RO 1 RO 0 reserved Type Reset reserved Type Reset RO 0 reserved RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 TXFE RO 1 UART Transmit FIFO Empty The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. If the FIFO is disabled (FEN is 0), this bit is set when the transmit holding register is empty. If the FIFO is enabled (FEN is 1), this bit is set when the transmit FIFO is empty. 6 RXFF RO 0 UART Receive FIFO Full The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. If the FIFO is disabled, this bit is set when the receive holding register is full. If the FIFO is enabled, this bit is set when the receive FIFO is full. 5 TXFF RO 0 UART Transmit FIFO Full The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. If the FIFO is disabled, this bit is set when the transmit holding register is full. If the FIFO is enabled, this bit is set when the transmit FIFO is full. 4 RXFE RO 1 UART Receive FIFO Empty The meaning of this bit depends on the state of the FEN bit in the UARTLCRH register. If the FIFO is disabled, this bit is set when the receive holding register is empty. If the FIFO is enabled, this bit is set when the receive FIFO is empty. July 14, 2014 335 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset Description 3 BUSY RO 0 UART Busy When this bit is 1, the UART is busy transmitting data. This bit remains set until the complete byte, including all stop bits, has been sent from the shift register. This bit is set as soon as the transmit FIFO becomes non-empty (regardless of whether UART is enabled). 2:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 336 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 4: UART Integer Baud-Rate Divisor (UARTIBRD), offset 0x024 The UARTIBRD register is the integer part of the baud-rate divisor value. All the bits are cleared on reset. The minimum possible divide ratio is 1 (when UARTIBRD=0), in which case the UARTFBRD register is ignored. When changing the UARTIBRD register, the new value does not take effect until transmission/reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register. See “Baud-Rate Generation” on page 325 for configuration details. UART Integer Baud-Rate Divisor (UARTIBRD) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset DIVINT Type Reset Bit/Field Name Type Reset 31:16 reserved RO 0 15:0 DIVINT R/W 0x0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. Integer Baud-Rate Divisor July 14, 2014 337 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 5: UART Fractional Baud-Rate Divisor (UARTFBRD), offset 0x028 The UARTFBRD register is the fractional part of the baud-rate divisor value. All the bits are cleared on reset. When changing the UARTFBRD register, the new value does not take effect until transmission/reception of the current character is complete. Any changes to the baud-rate divisor must be followed by a write to the UARTLCRH register. See “Baud-Rate Generation” on page 325 for configuration details. UART Fractional Baud-Rate Divisor (UARTFBRD) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x028 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 DIVFRAC R/W 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:0 DIVFRAC R/W 0x000 Fractional Baud-Rate Divisor 338 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 6: UART Line Control (UARTLCRH), offset 0x02C The UARTLCRH register is the line control register. Serial parameters such as data length, parity, and stop bit selection are implemented in this register. When updating the baud-rate divisor (UARTIBRD and/or UARTIFRD), the UARTLCRH register must also be written. The write strobe for the baud-rate divisor registers is tied to the UARTLCRH register. UART Line Control (UARTLCRH) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x02C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 reserved Type Reset RO 0 RO 0 RO 0 RO 0 SPS RO 0 RO 0 RO 0 RO 0 R/W 0 5 WLEN R/W 0 R/W 0 4 3 2 1 0 FEN STP2 EPS PEN BRK R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7 SPS R/W 0 UART Stick Parity Select When bits 1, 2, and 7 of UARTLCRH are set, the parity bit is transmitted and checked as a 0. When bits 1 and 7 are set and 2 is cleared, the parity bit is transmitted and checked as a 1. When this bit is cleared, stick parity is disabled. 6:5 WLEN R/W 0 UART Word Length The bits indicate the number of data bits transmitted or received in a frame as follows: Value Description 0x3 8 bits 0x2 7 bits 0x1 6 bits 0x0 5 bits (default) 4 FEN R/W 0 UART Enable FIFOs If this bit is set to 1, transmit and receive FIFO buffers are enabled (FIFO mode). When cleared to 0, FIFOs are disabled (Character mode). The FIFOs become 1-byte-deep holding registers. 3 STP2 R/W 0 UART Two Stop Bits Select If this bit is set to 1, two stop bits are transmitted at the end of a frame. The receive logic does not check for two stop bits being received. July 14, 2014 339 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 2 EPS R/W 0 Description UART Even Parity Select If this bit is set to 1, even parity generation and checking is performed during transmission and reception, which checks for an even number of 1s in data and parity bits. When cleared to 0, then odd parity is performed, which checks for an odd number of 1s. This bit has no effect when parity is disabled by the PEN bit. 1 PEN R/W 0 UART Parity Enable If this bit is set to 1, parity checking and generation is enabled; otherwise, parity is disabled and no parity bit is added to the data frame. 0 BRK R/W 0 UART Send Break If this bit is set to 1, a Low level is continually output on the UnTX output, after completing transmission of the current character. For the proper execution of the break command, the software must set this bit for at least two frames (character periods). For normal use, this bit must be cleared to 0. 340 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 7: UART Control (UARTCTL), offset 0x030 The UARTCTL register is the control register. All the bits are cleared on reset except for the Transmit Enable (TXE) and Receive Enable (RXE) bits, which are set to 1. To enable the UART module, the UARTEN bit must be set to 1. If software requires a configuration change in the module, the UARTEN bit must be cleared before the configuration changes are written. If the UART is disabled during a transmit or receive operation, the current transaction is completed prior to the UART stopping. Note: The UARTCTL register should not be changed while the UART is enabled or else the results are unpredictable. The following sequence is recommended for making changes to the UARTCTL register. 1. Disable the UART. 2. Wait for the end of transmission or reception of the current character. 3. Flush the transmit FIFO by disabling bit 4 (FEN) in the line control register (UARTLCRH). 4. Reprogram the control register. 5. Enable the UART. UART Control (UARTCTL) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x030 Type R/W, reset 0x0000.0300 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RXE TXE LBE RO 0 RO 0 RO 0 RO 0 RO 0 R/W 1 R/W 1 R/W 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 reserved UARTEN R/W 0 Bit/Field Name Type Reset Description 31:10 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 9 RXE R/W 1 UART Receive Enable If this bit is set to 1, the receive section of the UART is enabled. When the UART is disabled in the middle of a receive, it completes the current character before stopping. Note: 8 TXE R/W 1 To enable reception, the UARTEN bit must also be set. UART Transmit Enable If this bit is set to 1, the transmit section of the UART is enabled. When the UART is disabled in the middle of a transmission, it completes the current character before stopping. Note: To enable transmission, the UARTEN bit must also be set. July 14, 2014 341 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 7 LBE R/W 0 Description UART Loop Back Enable If this bit is set to 1, the UnTX path is fed through the UnRX path. 6:1 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 UARTEN R/W 0 UART Enable If this bit is set to 1, the UART is enabled. When the UART is disabled in the middle of transmission or reception, it completes the current character before stopping. 342 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: UART Interrupt FIFO Level Select (UARTIFLS), offset 0x034 The UARTIFLS register is the interrupt FIFO level select register. You can use this register to define the FIFO level at which the TXRIS and RXRIS bits in the UARTRIS register are triggered. The interrupts are generated based on a transition through a level rather than being based on the level. That is, the interrupts are generated when the fill level progresses through the trigger level. For example, if the receive trigger level is set to the half-way mark, the interrupt is triggered as the module is receiving the 9th character. Out of reset, the TXIFLSEL and RXIFLSEL bits are configured so that the FIFOs trigger an interrupt at the half-way mark. UART Interrupt FIFO Level Select (UARTIFLS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x034 Type R/W, reset 0x0000.0012 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 RXIFLSEL R/W 1 TXIFLSEL R/W 1 R/W 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5:3 RXIFLSEL R/W 0x2 UART Receive Interrupt FIFO Level Select The trigger points for the receive interrupt are as follows: Value Description 0x0 RX FIFO ≥ ⅛ full 0x1 RX FIFO ≥ ¼ full 0x2 RX FIFO ≥ ½ full (default) 0x3 RX FIFO ≥ ¾ full 0x4 RX FIFO ≥ ⅞ full 0x5-0x7 Reserved July 14, 2014 343 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 2:0 TXIFLSEL R/W 0x2 Description UART Transmit Interrupt FIFO Level Select The trigger points for the transmit interrupt are as follows: Value Description 0x0 TX FIFO ≤ ⅞ empty 0x1 TX FIFO ≤ ¾ empty 0x2 TX FIFO ≤ ½ empty (default) 0x3 TX FIFO ≤ ¼ empty 0x4 TX FIFO ≤ ⅛ empty 0x5-0x7 Reserved 344 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 9: UART Interrupt Mask (UARTIM), offset 0x038 The UARTIM register is the interrupt mask set/clear register. On a read, this register gives the current value of the mask on the relevant interrupt. Writing a 1 to a bit allows the corresponding raw interrupt signal to be routed to the interrupt controller. Writing a 0 prevents the raw interrupt signal from being sent to the interrupt controller. UART Interrupt Mask (UARTIM) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x038 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 15 14 RO 0 RO 0 RO 0 13 12 11 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 10 9 8 7 6 5 4 OEIM BEIM PEIM FEIM RTIM TXIM RXIM R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 RO 0 reserved RO 0 RO 0 Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEIM R/W 0 UART Overrun Error Interrupt Mask On a read, the current mask for the OEIM interrupt is returned. Setting this bit to 1 promotes the OEIM interrupt to the interrupt controller. 9 BEIM R/W 0 UART Break Error Interrupt Mask On a read, the current mask for the BEIM interrupt is returned. Setting this bit to 1 promotes the BEIM interrupt to the interrupt controller. 8 PEIM R/W 0 UART Parity Error Interrupt Mask On a read, the current mask for the PEIM interrupt is returned. Setting this bit to 1 promotes the PEIM interrupt to the interrupt controller. 7 FEIM R/W 0 UART Framing Error Interrupt Mask On a read, the current mask for the FEIM interrupt is returned. Setting this bit to 1 promotes the FEIM interrupt to the interrupt controller. 6 RTIM R/W 0 UART Receive Time-Out Interrupt Mask On a read, the current mask for the RTIM interrupt is returned. Setting this bit to 1 promotes the RTIM interrupt to the interrupt controller. 5 TXIM R/W 0 UART Transmit Interrupt Mask On a read, the current mask for the TXIM interrupt is returned. Setting this bit to 1 promotes the TXIM interrupt to the interrupt controller. 4 RXIM R/W 0 UART Receive Interrupt Mask On a read, the current mask for the RXIM interrupt is returned. Setting this bit to 1 promotes the RXIM interrupt to the interrupt controller. July 14, 2014 345 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset Description 3:0 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 346 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 10: UART Raw Interrupt Status (UARTRIS), offset 0x03C The UARTRIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt. A write has no effect. UART Raw Interrupt Status (UARTRIS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x03C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 OERIS RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BERIS PERIS FERIS RTRIS TXRIS RXRIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 reserved Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OERIS RO 0 UART Overrun Error Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 9 BERIS RO 0 UART Break Error Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 8 PERIS RO 0 UART Parity Error Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 7 FERIS RO 0 UART Framing Error Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 6 RTRIS RO 0 UART Receive Time-Out Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 5 TXRIS RO 0 UART Transmit Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 4 RXRIS RO 0 UART Receive Raw Interrupt Status Gives the raw interrupt state (prior to masking) of this interrupt. 3:0 reserved RO 0x0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. July 14, 2014 347 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 11: UART Masked Interrupt Status (UARTMIS), offset 0x040 The UARTMIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect. UART Masked Interrupt Status (UARTMIS) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x040 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 OEMIS RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BEMIS PEMIS FEMIS RTMIS TXMIS RXMIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 reserved Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEMIS RO 0 UART Overrun Error Masked Interrupt Status Gives the masked interrupt state of this interrupt. 9 BEMIS RO 0 UART Break Error Masked Interrupt Status Gives the masked interrupt state of this interrupt. 8 PEMIS RO 0 UART Parity Error Masked Interrupt Status Gives the masked interrupt state of this interrupt. 7 FEMIS RO 0 UART Framing Error Masked Interrupt Status Gives the masked interrupt state of this interrupt. 6 RTMIS RO 0 UART Receive Time-Out Masked Interrupt Status Gives the masked interrupt state of this interrupt. 5 TXMIS RO 0 UART Transmit Masked Interrupt Status Gives the masked interrupt state of this interrupt. 4 RXMIS RO 0 UART Receive Masked Interrupt Status Gives the masked interrupt state of this interrupt. 3:0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 348 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 12: UART Interrupt Clear (UARTICR), offset 0x044 The UARTICR register is the interrupt clear register. On a write of 1, the corresponding interrupt (both raw interrupt and masked interrupt, if enabled) is cleared. A write of 0 has no effect. UART Interrupt Clear (UARTICR) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0x044 Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 OEIC RO 0 RO 0 RO 0 RO 0 W1C 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BEIC PEIC FEIC RTIC TXIC RXIC W1C 0 W1C 0 W1C 0 W1C 0 W1C 0 W1C 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 reserved Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10 OEIC W1C 0 Overrun Error Interrupt Clear The OEIC values are defined as follows: Value Description 9 BEIC W1C 0 0 No effect on the interrupt. 1 Clears interrupt. Break Error Interrupt Clear The BEIC values are defined as follows: Value Description 8 PEIC W1C 0 0 No effect on the interrupt. 1 Clears interrupt. Parity Error Interrupt Clear The PEIC values are defined as follows: Value Description 7 FEIC W1C 0 0 No effect on the interrupt. 1 Clears interrupt. Framing Error Interrupt Clear The FEIC values are defined as follows: Value Description 0 No effect on the interrupt. 1 Clears interrupt. July 14, 2014 349 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Bit/Field Name Type Reset 6 RTIC W1C 0 Description Receive Time-Out Interrupt Clear The RTIC values are defined as follows: Value Description 5 TXIC W1C 0 0 No effect on the interrupt. 1 Clears interrupt. Transmit Interrupt Clear The TXIC values are defined as follows: Value Description 4 RXIC W1C 0 0 No effect on the interrupt. 1 Clears interrupt. Receive Interrupt Clear The RXIC values are defined as follows: Value Description 3:0 reserved RO 0x00 0 No effect on the interrupt. 1 Clears interrupt. Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 350 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 13: UART Peripheral Identification 4 (UARTPeriphID4), offset 0xFD0 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 4 (UARTPeriphID4) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID4 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID4 RO 0x0000 UART Peripheral ID Register[7:0] Can be used by software to identify the presence of this peripheral. July 14, 2014 351 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 14: UART Peripheral Identification 5 (UARTPeriphID5), offset 0xFD4 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 5 (UARTPeriphID5) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID5 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID5 RO 0x0000 UART Peripheral ID Register[15:8] Can be used by software to identify the presence of this peripheral. 352 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 15: UART Peripheral Identification 6 (UARTPeriphID6), offset 0xFD8 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 6 (UARTPeriphID6) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID6 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID6 RO 0x0000 UART Peripheral ID Register[23:16] Can be used by software to identify the presence of this peripheral. July 14, 2014 353 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 16: UART Peripheral Identification 7 (UARTPeriphID7), offset 0xFDC The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 7 (UARTPeriphID7) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID7 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0 7:0 PID7 RO 0x0000 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. UART Peripheral ID Register[31:24] Can be used by software to identify the presence of this peripheral. 354 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 17: UART Peripheral Identification 0 (UARTPeriphID0), offset 0xFE0 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 0 (UARTPeriphID0) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFE0 Type RO, reset 0x0000.0011 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset PID0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID0 RO 0x11 UART Peripheral ID Register[7:0] Can be used by software to identify the presence of this peripheral. July 14, 2014 355 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 18: UART Peripheral Identification 1 (UARTPeriphID1), offset 0xFE4 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 1 (UARTPeriphID1) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFE4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID1 RO 0x00 UART Peripheral ID Register[15:8] Can be used by software to identify the presence of this peripheral. 356 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 19: UART Peripheral Identification 2 (UARTPeriphID2), offset 0xFE8 The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 2 (UARTPeriphID2) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID2 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID2 RO 0x18 UART Peripheral ID Register[23:16] Can be used by software to identify the presence of this peripheral. July 14, 2014 357 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 20: UART Peripheral Identification 3 (UARTPeriphID3), offset 0xFEC The UARTPeriphIDn registers are hard-coded and the fields within the registers determine the reset values. UART Peripheral Identification 3 (UARTPeriphID3) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset PID3 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID3 RO 0x01 UART Peripheral ID Register[31:24] Can be used by software to identify the presence of this peripheral. 358 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 21: UART PrimeCell Identification 0 (UARTPCellID0), offset 0xFF0 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 0 (UARTPCellID0) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID0 RO 0x0D UART PrimeCell ID Register[7:0] Provides software a standard cross-peripheral identification system. July 14, 2014 359 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 22: UART PrimeCell Identification 1 (UARTPCellID1), offset 0xFF4 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 1 (UARTPCellID1) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 1 RO 1 RO 1 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset CID1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID1 RO 0xF0 UART PrimeCell ID Register[15:8] Provides software a standard cross-peripheral identification system. 360 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 23: UART PrimeCell Identification 2 (UARTPCellID2), offset 0xFF8 The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 2 (UARTPCellID2) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID2 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID2 RO 0x05 UART PrimeCell ID Register[23:16] Provides software a standard cross-peripheral identification system. July 14, 2014 361 Texas Instruments-Production Data Universal Asynchronous Receivers/Transmitters (UARTs) Register 24: UART PrimeCell Identification 3 (UARTPCellID3), offset 0xFFC The UARTPCellIDn registers are hard-coded and the fields within the registers determine the reset values. UART PrimeCell Identification 3 (UARTPCellID3) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 0 RO 1 RO 1 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset CID3 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID3 RO 0xB1 UART PrimeCell ID Register[31:24] Provides software a standard cross-peripheral identification system. 362 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 11 Synchronous Serial Interface (SSI) ® The Stellaris Synchronous Serial Interface (SSI) is a master or slave interface for synchronous serial communication with peripheral devices that have either Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces. The Stellaris SSI module has the following features: ■ Master or slave operation ■ Programmable clock bit rate and prescale ■ Separate transmit and receive FIFOs, 16 bits wide, 8 locations deep ■ Programmable interface operation for Freescale SPI, MICROWIRE, or Texas Instruments synchronous serial interfaces ■ Programmable data frame size from 4 to 16 bits ■ Internal loopback test mode for diagnostic/debug testing 11.1 Block Diagram Figure 11-1. SSI Module Block Diagram Interrupt Interrupt Control SSIIM SSIMIS Control/ Status SSIRIS SSIICR SSICR0 SSICR1 TxFIFO 8 x16 . . . SSITx SSISR SSIRx SSIDR RxFIFO 8 x16 System Clock SSIPCellID0 Identification Registers SSIPeriphID0 SSIPeriphID 4 SSIPCellID1 SSIPeriphID 1 SSIPeriphID 5 SSIPCellID2 SSIPeriphID 2 SSIPeriphID 6 SSIPCellID3 SSIPeriphID 3 SSIPeriphID7 11.2 Clock Prescaler Transmit / Receive Logic SSIClk SSIFss . . . SSICPSR Signal Description Table 11-1 on page 364 lists the external signals of the SSI module and describes the function of each. The SSI signals are alternate functions for some GPIO signals and default to be GPIO signals July 14, 2014 363 Texas Instruments-Production Data Synchronous Serial Interface (SSI) at reset., with the exception of the SSI0Clk, SSI0Fss, SSI0Rx, and SSI0Tx pins which default to the SSI function. The column in the table below titled "Pin Assignment" lists the possible GPIO pin placements for the SSI signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the SSI function. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 11-1. SSI Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type Description SSIClk 19 I/O TTL SSI clock. SSIFss 20 I/O TTL SSI frame. SSIRx 21 I TTL SSI receive. SSITx 22 O TTL SSI transmit. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 11.3 Functional Description The SSI performs serial-to-parallel conversion on data received from a peripheral device. The CPU accesses data, control, and status information. The transmit and receive paths are buffered with internal FIFO memories allowing up to eight 16-bit values to be stored independently in both transmit and receive modes. 11.3.1 Bit Rate Generation The SSI includes a programmable bit rate clock divider and prescaler to generate the serial output clock. Bit rates are supported to 1.5 MHz and higher, although maximum bit rate is determined by peripheral devices. The serial bit rate is derived by dividing down the input clock (FSysClk). The clock is first divided by an even prescale value CPSDVSR from 2 to 254, which is programmed in the SSI Clock Prescale (SSICPSR) register (see page 383). The clock is further divided by a value from 1 to 256, which is 1 + SCR, where SCR is the value programmed in the SSI Control0 (SSICR0) register (see page 376). The frequency of the output clock SSIClk is defined by: SSIClk = FSysClk / (CPSDVSR * (1 + SCR)) Note: For master mode, the system clock must be at least two times faster than the SSIClk. For slave mode, the system clock must be at least 12 times faster than the SSIClk. See “Synchronous Serial Interface (SSI)” on page 469 to view SSI timing parameters. 11.3.2 FIFO Operation 11.3.2.1 Transmit FIFO The common transmit FIFO is a 16-bit wide, 8-locations deep, first-in, first-out memory buffer. The CPU writes data to the FIFO by writing the SSI Data (SSIDR) register (see page 380), and data is stored in the FIFO until it is read out by the transmission logic. When configured as a master or a slave, parallel data is written into the transmit FIFO prior to serial conversion and transmission to the attached slave or master, respectively, through the SSITx pin. In slave mode, the SSI transmits data each time the master initiates a transaction. If the transmit FIFO is empty and the master initiates, the slave transmits the 8th most recent value in the transmit FIFO. If less than 8 values have been written to the transmit FIFO since the SSI module clock was 364 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller enabled using the SSI bit in the RGCG1 register, then 0 is transmitted. Care should be taken to ensure that valid data is in the FIFO as needed. The SSI can be configured to generate an interrupt when the FIFO is empty. 11.3.2.2 Receive FIFO The common receive FIFO is a 16-bit wide, 8-locations deep, first-in, first-out memory buffer. Received data from the serial interface is stored in the buffer until read out by the CPU, which accesses the read FIFO by reading the SSIDR register. When configured as a master or slave, serial data received through the SSIRx pin is registered prior to parallel loading into the attached slave or master receive FIFO, respectively. 11.3.3 Interrupts The SSI can generate interrupts when the following conditions are observed: ■ Transmit FIFO service ■ Receive FIFO service ■ Receive FIFO time-out ■ Receive FIFO overrun All of the interrupt events are ORed together before being sent to the interrupt controller, so the SSI can only generate a single interrupt request to the controller at any given time. You can mask each of the four individual maskable interrupts by setting the appropriate bits in the SSI Interrupt Mask (SSIIM) register (see page 384). Setting the appropriate mask bit to 1 enables the interrupt. Provision of the individual outputs, as well as a combined interrupt output, allows use of either a global interrupt service routine, or modular device drivers to handle interrupts. The transmit and receive dynamic dataflow interrupts have been separated from the status interrupts so that data can be read or written in response to the FIFO trigger levels. The status of the individual interrupt sources can be read from the SSI Raw Interrupt Status (SSIRIS) and SSI Masked Interrupt Status (SSIMIS) registers (see page 386 and page 387, respectively). 11.3.4 Frame Formats Each data frame is between 4 and 16 bits long, depending on the size of data programmed, and is transmitted starting with the MSB. There are three basic frame types that can be selected: ■ Texas Instruments synchronous serial ■ Freescale SPI ■ MICROWIRE For all three formats, the serial clock (SSIClk) is held inactive while the SSI is idle, and SSIClk transitions at the programmed frequency only during active transmission or reception of data. The idle state of SSIClk is utilized to provide a receive timeout indication that occurs when the receive FIFO still contains data after a timeout period. For Freescale SPI and MICROWIRE frame formats, the serial frame (SSIFss ) pin is active Low, and is asserted (pulled down) during the entire transmission of the frame. July 14, 2014 365 Texas Instruments-Production Data Synchronous Serial Interface (SSI) For Texas Instruments synchronous serial frame format, the SSIFss pin is pulsed for one serial clock period starting at its rising edge, prior to the transmission of each frame. For this frame format, both the SSI and the off-chip slave device drive their output data on the rising edge of SSIClk, and latch data from the other device on the falling edge. Unlike the full-duplex transmission of the other two frame formats, the MICROWIRE format uses a special master-slave messaging technique, which operates at half-duplex. In this mode, when a frame begins, an 8-bit control message is transmitted to the off-chip slave. During this transmit, no incoming data is received by the SSI. After the message has been sent, the off-chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control message has been sent, responds with the requested data. The returned data can be 4 to 16 bits in length, making the total frame length anywhere from 13 to 25 bits. 11.3.4.1 Texas Instruments Synchronous Serial Frame Format Figure 11-2 on page 366 shows the Texas Instruments synchronous serial frame format for a single transmitted frame. Figure 11-2. TI Synchronous Serial Frame Format (Single Transfer) SSIClk SSIFss SSITx/SSIRx MSB LSB 4 to 16 bits In this mode, SSIClk and SSIFss are forced Low, and the transmit data line SSITx is tristated whenever the SSI is idle. Once the bottom entry of the transmit FIFO contains data, SSIFss is pulsed High for one SSIClk period. The value to be transmitted is also transferred from the transmit FIFO to the serial shift register of the transmit logic. On the next rising edge of SSIClk, the MSB of the 4 to 16-bit data frame is shifted out on the SSITx pin. Likewise, the MSB of the received data is shifted onto the SSIRx pin by the off-chip serial slave device. Both the SSI and the off-chip serial slave device then clock each data bit into their serial shifter on the falling edge of each SSIClk. The received data is transferred from the serial shifter to the receive FIFO on the first rising edge of SSIClk after the LSB has been latched. Figure 11-3 on page 367 shows the Texas Instruments synchronous serial frame format when back-to-back frames are transmitted. 366 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 11-3. TI Synchronous Serial Frame Format (Continuous Transfer) SSIClk SSIFss SSITx/SSIRx MSB LSB 4 to 16 bits 11.3.4.2 Freescale SPI Frame Format The Freescale SPI interface is a four-wire interface where the SSIFss signal behaves as a slave select. The main feature of the Freescale SPI format is that the inactive state and phase of the SSIClk signal are programmable through the SPO and SPH bits within the SSISCR0 control register. SPO Clock Polarity Bit When the SPO clock polarity control bit is Low, it produces a steady state Low value on the SSIClk pin. If the SPO bit is High, a steady state High value is placed on the SSIClk pin when data is not being transferred. SPH Phase Control Bit The SPH phase control bit selects the clock edge that captures data and allows it to change state. It has the most impact on the first bit transmitted by either allowing or not allowing a clock transition before the first data capture edge. When the SPH phase control bit is Low, data is captured on the first clock edge transition. If the SPH bit is High, data is captured on the second clock edge transition. 11.3.4.3 Freescale SPI Frame Format with SPO=0 and SPH=0 Single and continuous transmission signal sequences for Freescale SPI format with SPO=0 and SPH=0 are shown in Figure 11-4 on page 367 and Figure 11-5 on page 368. Figure 11-4. Freescale SPI Format (Single Transfer) with SPO=0 and SPH=0 SSIClk SSIFss SSIRx LSB MSB Q 4 to 16 bits SSITx MSB Note: LSB Q is undefined. July 14, 2014 367 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Figure 11-5. Freescale SPI Format (Continuous Transfer) with SPO=0 and SPH=0 SSIClk SSIFss SSIRx LSB LSB MSB MSB 4 to16 bits SSITx LSB MSB LSB MSB In this configuration, during idle periods: ■ SSIClk is forced Low ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and there is valid data within the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low. This causes slave data to be enabled onto the SSIRx input line of the master. The master SSITx output pad is enabled. One half SSIClk period later, valid master data is transferred to the SSITx pin. Now that both the master and slave data have been set, the SSIClk master clock pin goes High after one further half SSIClk period. The data is now captured on the rising and propagated on the falling edges of the SSIClk signal. In the case of a single word transmission, after all bits of the data word have been transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. However, in the case of continuous back-to-back transmissions, the SSIFss signal must be pulsed High between each data word transfer. This is because the slave select pin freezes the data in its serial peripheral register and does not allow it to be altered if the SPH bit is logic zero. Therefore, the master device must raise the SSIFss pin of the slave device between each data transfer to enable the serial peripheral data write. On completion of the continuous transfer, the SSIFss pin is returned to its idle state one SSIClk period after the last bit has been captured. 11.3.4.4 Freescale SPI Frame Format with SPO=0 and SPH=1 The transfer signal sequence for Freescale SPI format with SPO=0 and SPH=1 is shown in Figure 11-6 on page 369, which covers both single and continuous transfers. 368 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 11-6. Freescale SPI Frame Format with SPO=0 and SPH=1 SSIClk SSIFss SSIRx Q MSB Q LSB Q 4 to 16 bits SSITx LSB MSB Note: Q is undefined. In this configuration, during idle periods: ■ SSIClk is forced Low ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and there is valid data within the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low. The master SSITx output is enabled. After a further one half SSIClk period, both master and slave valid data is enabled onto their respective transmission lines. At the same time, the SSIClk is enabled with a rising edge transition. Data is then captured on the falling edges and propagated on the rising edges of the SSIClk signal. In the case of a single word transfer, after all bits have been transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. For continuous back-to-back transfers, the SSIFss pin is held Low between successive data words and termination is the same as that of the single word transfer. 11.3.4.5 Freescale SPI Frame Format with SPO=1 and SPH=0 Single and continuous transmission signal sequences for Freescale SPI format with SPO=1 and SPH=0 are shown in Figure 11-7 on page 369 and Figure 11-8 on page 370. Figure 11-7. Freescale SPI Frame Format (Single Transfer) with SPO=1 and SPH=0 SSIClk SSIFss SSIRx MSB LSB Q 4 to 16 bits SSITx LSB MSB Note: Q is undefined. July 14, 2014 369 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Figure 11-8. Freescale SPI Frame Format (Continuous Transfer) with SPO=1 and SPH=0 SSIClk SSIFss SSITx/SSIRx MSB LSB LSB MSB 4 to 16 bits In this configuration, during idle periods: ■ SSIClk is forced High ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and there is valid data within the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low, which causes slave data to be immediately transferred onto the SSIRx line of the master. The master SSITx output pad is enabled. One half period later, valid master data is transferred to the SSITx line. Now that both the master and slave data have been set, the SSIClk master clock pin becomes Low after one further half SSIClk period. This means that data is captured on the falling edges and propagated on the rising edges of the SSIClk signal. In the case of a single word transmission, after all bits of the data word are transferred, the SSIFss line is returned to its idle High state one SSIClk period after the last bit has been captured. However, in the case of continuous back-to-back transmissions, the SSIFss signal must be pulsed High between each data word transfer. This is because the slave select pin freezes the data in its serial peripheral register and does not allow it to be altered if the SPH bit is logic zero. Therefore, the master device must raise the SSIFss pin of the slave device between each data transfer to enable the serial peripheral data write. On completion of the continuous transfer, the SSIFss pin is returned to its idle state one SSIClk period after the last bit has been captured. 11.3.4.6 Freescale SPI Frame Format with SPO=1 and SPH=1 The transfer signal sequence for Freescale SPI format with SPO=1 and SPH=1 is shown in Figure 11-9 on page 371, which covers both single and continuous transfers. 370 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 11-9. Freescale SPI Frame Format with SPO=1 and SPH=1 SSIClk SSIFss SSIRx Q MSB LSB Q 4 to 16 bits MSB SSITx Note: LSB Q is undefined. In this configuration, during idle periods: ■ SSIClk is forced High ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low ■ When the SSI is configured as a master, it enables the SSIClk pad ■ When the SSI is configured as a slave, it disables the SSIClk pad If the SSI is enabled and there is valid data within the transmit FIFO, the start of transmission is signified by the SSIFss master signal being driven Low. The master SSITx output pad is enabled. After a further one-half SSIClk period, both master and slave data are enabled onto their respective transmission lines. At the same time, SSIClk is enabled with a falling edge transition. Data is then captured on the rising edges and propagated on the falling edges of the SSIClk signal. After all bits have been transferred, in the case of a single word transmission, the SSIFss line is returned to its idle high state one SSIClk period after the last bit has been captured. For continuous back-to-back transmissions, the SSIFss pin remains in its active Low state, until the final bit of the last word has been captured, and then returns to its idle state as described above. For continuous back-to-back transfers, the SSIFss pin is held Low between successive data words and termination is the same as that of the single word transfer. 11.3.4.7 MICROWIRE Frame Format Figure 11-10 on page 371 shows the MICROWIRE frame format, again for a single frame. Figure 11-11 on page 372 shows the same format when back-to-back frames are transmitted. Figure 11-10. MICROWIRE Frame Format (Single Frame) SSIClk SSIFss SSITx LSB MSB 8-bit control SSIRx 0 MSB LSB 4 to 16 bits output data July 14, 2014 371 Texas Instruments-Production Data Synchronous Serial Interface (SSI) MICROWIRE format is very similar to SPI format, except that transmission is half-duplex instead of full-duplex, using a master-slave message passing technique. Each serial transmission begins with an 8-bit control word that is transmitted from the SSI to the off-chip slave device. During this transmission, no incoming data is received by the SSI. After the message has been sent, the off-chip slave decodes it and, after waiting one serial clock after the last bit of the 8-bit control message has been sent, responds with the required data. The returned data is 4 to 16 bits in length, making the total frame length anywhere from 13 to 25 bits. In this configuration, during idle periods: ■ SSIClk is forced Low ■ SSIFss is forced High ■ The transmit data line SSITx is arbitrarily forced Low A transmission is triggered by writing a control byte to the transmit FIFO. The falling edge of SSIFss causes the value contained in the bottom entry of the transmit FIFO to be transferred to the serial shift register of the transmit logic, and the MSB of the 8-bit control frame to be shifted out onto the SSITx pin. SSIFss remains Low for the duration of the frame transmission. The SSIRx pin remains tristated during this transmission. The off-chip serial slave device latches each control bit into its serial shifter on the rising edge of each SSIClk. After the last bit is latched by the slave device, the control byte is decoded during a one clock wait-state, and the slave responds by transmitting data back to the SSI. Each bit is driven onto the SSIRx line on the falling edge of SSIClk. The SSI in turn latches each bit on the rising edge of SSIClk. At the end of the frame, for single transfers, the SSIFss signal is pulled High one clock period after the last bit has been latched in the receive serial shifter, which causes the data to be transferred to the receive FIFO. Note: The off-chip slave device can tristate the receive line either on the falling edge of SSIClk after the LSB has been latched by the receive shifter, or when the SSIFss pin goes High. For continuous transfers, data transmission begins and ends in the same manner as a single transfer. However, the SSIFss line is continuously asserted (held Low) and transmission of data occurs back-to-back. The control byte of the next frame follows directly after the LSB of the received data from the current frame. Each of the received values is transferred from the receive shifter on the falling edge of SSIClk, after the LSB of the frame has been latched into the SSI. Figure 11-11. MICROWIRE Frame Format (Continuous Transfer) SSIClk SSIFss SSITx LSB MSB LSB 8-bit control SSIRx 0 MSB LSB MSB 4 to 16 bits output data In the MICROWIRE mode, the SSI slave samples the first bit of receive data on the rising edge of SSIClk after SSIFss has gone Low. Masters that drive a free-running SSIClk must ensure that the SSIFss signal has sufficient setup and hold margins with respect to the rising edge of SSIClk. 372 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 11-12 on page 373 illustrates these setup and hold time requirements. With respect to the SSIClk rising edge on which the first bit of receive data is to be sampled by the SSI slave, SSIFss must have a setup of at least two times the period of SSIClk on which the SSI operates. With respect to the SSIClk rising edge previous to this edge, SSIFss must have a hold of at least one SSIClk period. Figure 11-12. MICROWIRE Frame Format, SSIFss Input Setup and Hold Requirements tSetup=(2*tSSIClk) tHold=tSSIClk SSIClk SSIFss SSIRx First RX data to be sampled by SSI slave 11.4 Initialization and Configuration To use the SSI, its peripheral clock must be enabled by setting the SSI bit in the RCGC1 register. For each of the frame formats, the SSI is configured using the following steps: 1. Ensure that the SSE bit in the SSICR1 register is disabled before making any configuration changes. 2. Select whether the SSI is a master or slave: a. For master operations, set the SSICR1 register to 0x0000.0000. b. For slave mode (output enabled), set the SSICR1 register to 0x0000.0004. c. For slave mode (output disabled), set the SSICR1 register to 0x0000.000C. 3. Configure the clock prescale divisor by writing the SSICPSR register. 4. Write the SSICR0 register with the following configuration: ■ Serial clock rate (SCR) ■ Desired clock phase/polarity, if using Freescale SPI mode (SPH and SPO) ■ The protocol mode: Freescale SPI, TI SSF, MICROWIRE (FRF) ■ The data size (DSS) 5. Enable the SSI by setting the SSE bit in the SSICR1 register. As an example, assume the SSI must be configured to operate with the following parameters: ■ Master operation July 14, 2014 373 Texas Instruments-Production Data Synchronous Serial Interface (SSI) ■ Freescale SPI mode (SPO=1, SPH=1) ■ 1 Mbps bit rate ■ 8 data bits Assuming the system clock is 20 MHz, the bit rate calculation would be: FSSIClk = FSysClk / (CPSDVSR * (1 + SCR)) 1x106 = 20x106 / (CPSDVSR * (1 + SCR)) In this case, if CPSDVSR=2, SCR must be 9. The configuration sequence would be as follows: 1. Ensure that the SSE bit in the SSICR1 register is disabled. 2. Write the SSICR1 register with a value of 0x0000.0000. 3. Write the SSICPSR register with a value of 0x0000.0002. 4. Write the SSICR0 register with a value of 0x0000.09C7. 5. The SSI is then enabled by setting the SSE bit in the SSICR1 register to 1. 11.5 Register Map Table 11-2 on page 374 lists the SSI registers. The offset listed is a hexadecimal increment to the register’s address, relative to that SSI module’s base address: ■ SSI0: 0x4000.8000 Note that the SSI module clock must be enabled before the registers can be programmed (see page 190). There must be a delay of 3 system clocks after the SSI module clock is enabled before any SSI module registers are accessed. Note: The SSI must be disabled (see the SSE bit in the SSICR1 register) before any of the control registers are reprogrammed. Table 11-2. SSI Register Map Offset Name Type Reset Description See page 0x000 SSICR0 R/W 0x0000.0000 SSI Control 0 376 0x004 SSICR1 R/W 0x0000.0000 SSI Control 1 378 0x008 SSIDR R/W 0x0000.0000 SSI Data 380 0x00C SSISR RO 0x0000.0003 SSI Status 381 0x010 SSICPSR R/W 0x0000.0000 SSI Clock Prescale 383 0x014 SSIIM R/W 0x0000.0000 SSI Interrupt Mask 384 0x018 SSIRIS RO 0x0000.0008 SSI Raw Interrupt Status 386 0x01C SSIMIS RO 0x0000.0000 SSI Masked Interrupt Status 387 374 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 11-2. SSI Register Map (continued) Name Type Reset 0x020 SSIICR W1C 0x0000.0000 SSI Interrupt Clear 388 0xFD0 SSIPeriphID4 RO 0x0000.0000 SSI Peripheral Identification 4 389 0xFD4 SSIPeriphID5 RO 0x0000.0000 SSI Peripheral Identification 5 390 0xFD8 SSIPeriphID6 RO 0x0000.0000 SSI Peripheral Identification 6 391 0xFDC SSIPeriphID7 RO 0x0000.0000 SSI Peripheral Identification 7 392 0xFE0 SSIPeriphID0 RO 0x0000.0022 SSI Peripheral Identification 0 393 0xFE4 SSIPeriphID1 RO 0x0000.0000 SSI Peripheral Identification 1 394 0xFE8 SSIPeriphID2 RO 0x0000.0018 SSI Peripheral Identification 2 395 0xFEC SSIPeriphID3 RO 0x0000.0001 SSI Peripheral Identification 3 396 0xFF0 SSIPCellID0 RO 0x0000.000D SSI PrimeCell Identification 0 397 0xFF4 SSIPCellID1 RO 0x0000.00F0 SSI PrimeCell Identification 1 398 0xFF8 SSIPCellID2 RO 0x0000.0005 SSI PrimeCell Identification 2 399 0xFFC SSIPCellID3 RO 0x0000.00B1 SSI PrimeCell Identification 3 400 11.6 Description See page Offset Register Descriptions The remainder of this section lists and describes the SSI registers, in numerical order by address offset. July 14, 2014 375 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 1: SSI Control 0 (SSICR0), offset 0x000 SSICR0 is control register 0 and contains bit fields that control various functions within the SSI module. Functionality such as protocol mode, clock rate, and data size are configured in this register. SSI Control 0 (SSICR0) SSI0 base: 0x4000.8000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 SPH SPO R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset SCR Type Reset FRF R/W 0 DSS Bit/Field Name Type Reset Description 31:16 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:8 SCR R/W 0x0000 SSI Serial Clock Rate The value SCR is used to generate the transmit and receive bit rate of the SSI. The bit rate is: BR=FSSIClk/(CPSDVSR * (1 + SCR)) where CPSDVSR is an even value from 2-254 programmed in the SSICPSR register, and SCR is a value from 0-255. 7 SPH R/W 0 SSI Serial Clock Phase This bit is only applicable to the Freescale SPI Format. The SPH control bit selects the clock edge that captures data and allows it to change state. It has the most impact on the first bit transmitted by either allowing or not allowing a clock transition before the first data capture edge. When the SPH bit is 0, data is captured on the first clock edge transition. If SPH is 1, data is captured on the second clock edge transition. 6 SPO R/W 0 SSI Serial Clock Polarity This bit is only applicable to the Freescale SPI Format. When the SPO bit is 0, it produces a steady state Low value on the SSIClk pin. If SPO is 1, a steady state High value is placed on the SSIClk pin when data is not being transferred. 5:4 FRF R/W 0x0 SSI Frame Format Select The FRF values are defined as follows: Value Frame Format 0x0 Freescale SPI Frame Format 0x1 Texas Instruments Synchronous Serial Frame Format 0x2 MICROWIRE Frame Format 0x3 Reserved 376 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset Description 3:0 DSS R/W 0x00 SSI Data Size Select The DSS values are defined as follows: Value Data Size 0x0-0x2 Reserved 0x3 4-bit data 0x4 5-bit data 0x5 6-bit data 0x6 7-bit data 0x7 8-bit data 0x8 9-bit data 0x9 10-bit data 0xA 11-bit data 0xB 12-bit data 0xC 13-bit data 0xD 14-bit data 0xE 15-bit data 0xF 16-bit data July 14, 2014 377 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 2: SSI Control 1 (SSICR1), offset 0x004 SSICR1 is control register 1 and contains bit fields that control various functions within the SSI module. Master and slave mode functionality is controlled by this register. SSI Control 1 (SSICR1) SSI0 base: 0x4000.8000 Offset 0x004 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 SOD MS SSE LBM RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 SOD R/W 0 SSI Slave Mode Output Disable This bit is relevant only in the Slave mode (MS=1). In multiple-slave systems, it is possible for the SSI master to broadcast a message to all slaves in the system while ensuring that only one slave drives data onto the serial output line. In such systems, the TXD lines from multiple slaves could be tied together. To operate in such a system, the SOD bit can be configured so that the SSI slave does not drive the SSITx pin. The SOD values are defined as follows: Value Description 2 MS R/W 0 0 SSI can drive SSITx output in Slave Output mode. 1 SSI must not drive the SSITx output in Slave mode. SSI Master/Slave Select This bit selects Master or Slave mode and can be modified only when SSI is disabled (SSE=0). The MS values are defined as follows: Value Description 0 Device configured as a master. 1 Device configured as a slave. 378 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 1 SSE R/W 0 Description SSI Synchronous Serial Port Enable Setting this bit enables SSI operation. The SSE values are defined as follows: Value Description 0 SSI operation disabled. 1 SSI operation enabled. Note: 0 LBM R/W 0 This bit must be set to 0 before any control registers are reprogrammed. SSI Loopback Mode Setting this bit enables Loopback Test mode. The LBM values are defined as follows: Value Description 0 Normal serial port operation enabled. 1 Output of the transmit serial shift register is connected internally to the input of the receive serial shift register. July 14, 2014 379 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 3: SSI Data (SSIDR), offset 0x008 Important: This register is read-sensitive. See the register description for details. SSIDR is the data register and is 16-bits wide. When SSIDR is read, the entry in the receive FIFO (pointed to by the current FIFO read pointer) is accessed. As data values are removed by the SSI receive logic from the incoming data frame, they are placed into the entry in the receive FIFO (pointed to by the current FIFO write pointer). When SSIDR is written to, the entry in the transmit FIFO (pointed to by the write pointer) is written to. Data values are removed from the transmit FIFO one value at a time by the transmit logic. It is loaded into the transmit serial shifter, then serially shifted out onto the SSITx pin at the programmed bit rate. When a data size of less than 16 bits is selected, the user must right-justify data written to the transmit FIFO. The transmit logic ignores the unused bits. Received data less than 16 bits is automatically right-justified in the receive buffer. When the SSI is programmed for MICROWIRE frame format, the default size for transmit data is eight bits (the most significant byte is ignored). The receive data size is controlled by the programmer. The transmit FIFO and the receive FIFO are not cleared even when the SSE bit in the SSICR1 register is set to zero. This allows the software to fill the transmit FIFO before enabling the SSI. SSI Data (SSIDR) SSI0 base: 0x4000.8000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 DATA Type Reset R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:16 reserved RO 0x0000 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 15:0 DATA R/W 0x0000 SSI Receive/Transmit Data A read operation reads the receive FIFO. A write operation writes the transmit FIFO. Software must right-justify data when the SSI is programmed for a data size that is less than 16 bits. Unused bits at the top are ignored by the transmit logic. The receive logic automatically right-justifies the data. 380 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 4: SSI Status (SSISR), offset 0x00C SSISR is a status register that contains bits that indicate the FIFO fill status and the SSI busy status. SSI Status (SSISR) SSI0 base: 0x4000.8000 Offset 0x00C Type RO, reset 0x0000.0003 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BSY RFF RNE TNF TFE RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 R0 1 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:5 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 BSY RO 0 SSI Busy Bit The BSY values are defined as follows: Value Description 3 RFF RO 0 0 SSI is idle. 1 SSI is currently transmitting and/or receiving a frame, or the transmit FIFO is not empty. SSI Receive FIFO Full The RFF values are defined as follows: Value Description 2 RNE RO 0 0 Receive FIFO is not full. 1 Receive FIFO is full. SSI Receive FIFO Not Empty The RNE values are defined as follows: Value Description 1 TNF RO 1 0 Receive FIFO is empty. 1 Receive FIFO is not empty. SSI Transmit FIFO Not Full The TNF values are defined as follows: Value Description 0 Transmit FIFO is full. 1 Transmit FIFO is not full. July 14, 2014 381 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Bit/Field Name Type Reset 0 TFE R0 1 Description SSI Transmit FIFO Empty The TFE values are defined as follows: Value Description 0 Transmit FIFO is not empty. 1 Transmit FIFO is empty. 382 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 5: SSI Clock Prescale (SSICPSR), offset 0x010 SSICPSR is the clock prescale register and specifies the division factor by which the system clock must be internally divided before further use. The value programmed into this register must be an even number between 2 and 254. The least-significant bit of the programmed number is hard-coded to zero. If an odd number is written to this register, data read back from this register has the least-significant bit as zero. SSI Clock Prescale (SSICPSR) SSI0 base: 0x4000.8000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 CPSDVSR RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CPSDVSR R/W 0x00 SSI Clock Prescale Divisor This value must be an even number from 2 to 254, depending on the frequency of SSIClk. The LSB always returns 0 on reads. July 14, 2014 383 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 6: SSI Interrupt Mask (SSIIM), offset 0x014 The SSIIM register is the interrupt mask set or clear register. It is a read/write register and all bits are cleared to 0 on reset. On a read, this register gives the current value of the mask on the relevant interrupt. A write of 1 to the particular bit sets the mask, enabling the interrupt to be read. A write of 0 clears the corresponding mask. SSI Interrupt Mask (SSIIM) SSI0 base: 0x4000.8000 Offset 0x014 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 3 2 1 0 TXIM RXIM RTIM RORIM R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXIM R/W 0 SSI Transmit FIFO Interrupt Mask The TXIM values are defined as follows: Value Description 2 RXIM R/W 0 0 TX FIFO half-empty or less condition interrupt is masked. 1 TX FIFO half-empty or less condition interrupt is not masked. SSI Receive FIFO Interrupt Mask The RXIM values are defined as follows: Value Description 1 RTIM R/W 0 0 RX FIFO half-full or more condition interrupt is masked. 1 RX FIFO half-full or more condition interrupt is not masked. SSI Receive Time-Out Interrupt Mask The RTIM values are defined as follows: Value Description 0 RX FIFO time-out interrupt is masked. 1 RX FIFO time-out interrupt is not masked. 384 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 0 RORIM R/W 0 Description SSI Receive Overrun Interrupt Mask The RORIM values are defined as follows: Value Description 0 RX FIFO overrun interrupt is masked. 1 RX FIFO overrun interrupt is not masked. July 14, 2014 385 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 7: SSI Raw Interrupt Status (SSIRIS), offset 0x018 The SSIRIS register is the raw interrupt status register. On a read, this register gives the current raw status value of the corresponding interrupt prior to masking. A write has no effect. SSI Raw Interrupt Status (SSIRIS) SSI0 base: 0x4000.8000 Offset 0x018 Type RO, reset 0x0000.0008 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TXRIS RXRIS RTRIS RORRIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXRIS RO 1 SSI Transmit FIFO Raw Interrupt Status Indicates that the transmit FIFO is half empty or less, when set. 2 RXRIS RO 0 SSI Receive FIFO Raw Interrupt Status Indicates that the receive FIFO is half full or more, when set. 1 RTRIS RO 0 SSI Receive Time-Out Raw Interrupt Status Indicates that the receive time-out has occurred, when set. 0 RORRIS RO 0 SSI Receive Overrun Raw Interrupt Status Indicates that the receive FIFO has overflowed, when set. 386 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: SSI Masked Interrupt Status (SSIMIS), offset 0x01C The SSIMIS register is the masked interrupt status register. On a read, this register gives the current masked status value of the corresponding interrupt. A write has no effect. SSI Masked Interrupt Status (SSIMIS) SSI0 base: 0x4000.8000 Offset 0x01C Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 TXMIS RXMIS RTMIS RORMIS RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:4 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 TXMIS RO 0 SSI Transmit FIFO Masked Interrupt Status Indicates that the transmit FIFO is half empty or less, when set. 2 RXMIS RO 0 SSI Receive FIFO Masked Interrupt Status Indicates that the receive FIFO is half full or more, when set. 1 RTMIS RO 0 SSI Receive Time-Out Masked Interrupt Status Indicates that the receive time-out has occurred, when set. 0 RORMIS RO 0 SSI Receive Overrun Masked Interrupt Status Indicates that the receive FIFO has overflowed, when set. July 14, 2014 387 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 9: SSI Interrupt Clear (SSIICR), offset 0x020 The SSIICR register is the interrupt clear register. On a write of 1, the corresponding interrupt is cleared. A write of 0 has no effect. SSI Interrupt Clear (SSIICR) SSI0 base: 0x4000.8000 Offset 0x020 Type W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RTIC RORIC RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 W1C 0 W1C 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:2 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 RTIC W1C 0 SSI Receive Time-Out Interrupt Clear The RTIC values are defined as follows: Value Description 0 RORIC W1C 0 0 No effect on interrupt. 1 Clears interrupt. SSI Receive Overrun Interrupt Clear The RORIC values are defined as follows: Value Description 0 No effect on interrupt. 1 Clears interrupt. 388 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 10: SSI Peripheral Identification 4 (SSIPeriphID4), offset 0xFD0 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 4 (SSIPeriphID4) SSI0 base: 0x4000.8000 Offset 0xFD0 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID4 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID4 RO 0x00 SSI Peripheral ID Register[7:0] Can be used by software to identify the presence of this peripheral. July 14, 2014 389 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 11: SSI Peripheral Identification 5 (SSIPeriphID5), offset 0xFD4 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 5 (SSIPeriphID5) SSI0 base: 0x4000.8000 Offset 0xFD4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID5 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID5 RO 0x00 SSI Peripheral ID Register[15:8] Can be used by software to identify the presence of this peripheral. 390 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 12: SSI Peripheral Identification 6 (SSIPeriphID6), offset 0xFD8 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 6 (SSIPeriphID6) SSI0 base: 0x4000.8000 Offset 0xFD8 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID6 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID6 RO 0x00 SSI Peripheral ID Register[23:16] Can be used by software to identify the presence of this peripheral. July 14, 2014 391 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 13: SSI Peripheral Identification 7 (SSIPeriphID7), offset 0xFDC The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 7 (SSIPeriphID7) SSI0 base: 0x4000.8000 Offset 0xFDC Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID7 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID7 RO 0x00 SSI Peripheral ID Register[31:24] Can be used by software to identify the presence of this peripheral. 392 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 14: SSI Peripheral Identification 0 (SSIPeriphID0), offset 0xFE0 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 0 (SSIPeriphID0) SSI0 base: 0x4000.8000 Offset 0xFE0 Type RO, reset 0x0000.0022 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 0 RO 0 RO 1 RO 0 reserved Type Reset reserved Type Reset PID0 RO 0 Bit/Field Name Type Reset 31:8 reserved RO 0 7:0 PID0 RO 0x22 Description Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. SSI Peripheral ID Register[7:0] Can be used by software to identify the presence of this peripheral. July 14, 2014 393 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 15: SSI Peripheral Identification 1 (SSIPeriphID1), offset 0xFE4 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 1 (SSIPeriphID1) SSI0 base: 0x4000.8000 Offset 0xFE4 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID1 RO 0x00 SSI Peripheral ID Register [15:8] Can be used by software to identify the presence of this peripheral. 394 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 16: SSI Peripheral Identification 2 (SSIPeriphID2), offset 0xFE8 The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 2 (SSIPeriphID2) SSI0 base: 0x4000.8000 Offset 0xFE8 Type RO, reset 0x0000.0018 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset PID2 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID2 RO 0x18 SSI Peripheral ID Register [23:16] Can be used by software to identify the presence of this peripheral. July 14, 2014 395 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 17: SSI Peripheral Identification 3 (SSIPeriphID3), offset 0xFEC The SSIPeriphIDn registers are hard-coded and the fields within the register determine the reset value. SSI Peripheral Identification 3 (SSIPeriphID3) SSI0 base: 0x4000.8000 Offset 0xFEC Type RO, reset 0x0000.0001 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset PID3 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 PID3 RO 0x01 SSI Peripheral ID Register [31:24] Can be used by software to identify the presence of this peripheral. 396 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 18: SSI PrimeCell Identification 0 (SSIPCellID0), offset 0xFF0 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 0 (SSIPCellID0) SSI0 base: 0x4000.8000 Offset 0xFF0 Type RO, reset 0x0000.000D 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID0 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID0 RO 0x0D SSI PrimeCell ID Register [7:0] Provides software a standard cross-peripheral identification system. July 14, 2014 397 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 19: SSI PrimeCell Identification 1 (SSIPCellID1), offset 0xFF4 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 1 (SSIPCellID1) SSI0 base: 0x4000.8000 Offset 0xFF4 Type RO, reset 0x0000.00F0 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 1 RO 1 RO 1 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset CID1 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID1 RO 0xF0 SSI PrimeCell ID Register [15:8] Provides software a standard cross-peripheral identification system. 398 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 20: SSI PrimeCell Identification 2 (SSIPCellID2), offset 0xFF8 The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 2 (SSIPCellID2) SSI0 base: 0x4000.8000 Offset 0xFF8 Type RO, reset 0x0000.0005 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 1 RO 0 RO 1 reserved Type Reset reserved Type Reset CID2 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID2 RO 0x05 SSI PrimeCell ID Register [23:16] Provides software a standard cross-peripheral identification system. July 14, 2014 399 Texas Instruments-Production Data Synchronous Serial Interface (SSI) Register 21: SSI PrimeCell Identification 3 (SSIPCellID3), offset 0xFFC The SSIPCellIDn registers are hard-coded, and the fields within the register determine the reset value. SSI PrimeCell Identification 3 (SSIPCellID3) SSI0 base: 0x4000.8000 Offset 0xFFC Type RO, reset 0x0000.00B1 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 RO 1 RO 0 RO 1 RO 1 RO 0 RO 0 RO 0 RO 1 reserved Type Reset reserved Type Reset CID3 RO 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 CID3 RO 0xB1 SSI PrimeCell ID Register [31:24] Provides software a standard cross-peripheral identification system. 400 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 12 Inter-Integrated Circuit (I2C) Interface The Inter-Integrated Circuit (I2C) bus provides bi-directional data transfer through a two-wire design (a serial data line SDA and a serial clock line SCL), and interfaces to external I2C devices such as serial memory (RAMs and ROMs), networking devices, LCDs, tone generators, and so on. The I2C bus may also be used for system testing and diagnostic purposes in product development and manufacture. The LM3S600 microcontroller includes one I2C module, providing the ability to interact (both send and receive) with other I2C devices on the bus. ® The Stellaris I2C interface has the following features: ■ Devices on the I2C bus can be designated as either a master or a slave – Supports both sending and receiving data as either a master or a slave – Supports simultaneous master and slave operation ■ Four I2C modes – Master transmit – Master receive – Slave transmit – Slave receive ■ Two transmission speeds: Standard (100 Kbps) and Fast (400 Kbps) ■ Master and slave interrupt generation – Master generates interrupts when a transmit or receive operation completes (or aborts due to an error) – Slave generates interrupts when data has been sent or requested by a master ■ Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode July 14, 2014 401 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface 12.1 Block Diagram Figure 12-1. I2C Block Diagram I2CSCL I2C Control Interrupt I2CMSA I2CSOAR I2CMCS I2CSCSR I2CMDR I2CSDR I2CMTPR I2CSIM I2CMIMR I2CSRIS I2CMRIS I2CSMIS I2CMMIS I2CSICR I2C Master Core I2CSCL I2C I/O Select I2CSDA I2CSCL I2C Slave Core I2CMICR I2CSDA I2CMCR 12.2 I2CSDA Signal Description Table 12-1 on page 402 lists the external signals of the I2C interface and describes the function of each. The I2C interface signals are alternate functions for some GPIO signals and default to be GPIO signals at reset., with the exception of the I2C0SCL and I2CSDA pins which default to the I2C function. The column in the table below titled "Pin Assignment" lists the possible GPIO pin placements for the I2C signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the I2C function. Note that the I2C pins should be set to open drain using the GPIO Open Drain Select (GPIOODR) register. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 12-1. I2C Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type Description I2CSCL 33 I/O OD I2C clock. I2CSDA 34 I/O OD I2C data. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 12.3 Functional Description I2C module is comprised of both master and slave functions which are implemented as separate peripherals. For proper operation, the SDA and SCL pins must be connected to bi-directional open-drain pads. A typical I2C bus configuration is shown in Figure 12-2 on page 403. See “Inter-Integrated Circuit (I2C) Interface” on page 470 for I2C timing diagrams. 402 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 12-2. I2C Bus Configuration RPUP SCL SDA I2C Bus I2CSCL I2CSDA Stellaris® 12.3.1 RPUP SCL SDA 3rd Party Device with I2C Interface SCL SDA 3rd Party Device with I2C Interface I2C Bus Functional Overview The I2C bus uses only two signals: SDA and SCL, named I2CSDA and I2CSCL on Stellaris microcontrollers. SDA is the bi-directional serial data line and SCL is the bi-directional serial clock line. The bus is considered idle when both lines are High. Every transaction on the I2C bus is nine bits long, consisting of eight data bits and a single acknowledge bit. The number of bytes per transfer (defined as the time between a valid START and STOP condition, described in “START and STOP Conditions” on page 403) is unrestricted, but each byte has to be followed by an acknowledge bit, and data must be transferred MSB first. When a receiver cannot receive another complete byte, it can hold the clock line SCL Low and force the transmitter into a wait state. The data transfer continues when the receiver releases the clock SCL. 12.3.1.1 START and STOP Conditions The protocol of the I2C bus defines two states to begin and end a transaction: START and STOP. A High-to-Low transition on the SDA line while the SCL is High is defined as a START condition, and a Low-to-High transition on the SDA line while SCL is High is defined as a STOP condition. The bus is considered busy after a START condition and free after a STOP condition. See Figure 12-3 on page 403. Figure 12-3. START and STOP Conditions SDA SDA SCL SCL START condition 12.3.1.2 STOP condition Data Format with 7-Bit Address Data transfers follow the format shown in Figure 12-4 on page 404. After the START condition, a slave address is sent. This address is 7-bits long followed by an eighth bit, which is a data direction bit (R/S bit in the I2CMSA register). A zero indicates a transmit operation (send), and a one indicates a request for data (receive). A data transfer is always terminated by a STOP condition generated by the master, however, a master can initiate communications with another device on the bus by generating a repeated START condition and addressing another slave without first generating a STOP condition. Various combinations of receive/send formats are then possible within a single transfer. July 14, 2014 403 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Figure 12-4. Complete Data Transfer with a 7-Bit Address SDA MSB SCL 1 2 LSB R/S ACK 7 8 9 MSB 1 2 Slave address 7 LSB ACK 8 9 Data The first seven bits of the first byte make up the slave address (see Figure 12-5 on page 404). The eighth bit determines the direction of the message. A zero in the R/S position of the first byte means that the master will write (send) data to the selected slave, and a one in this position means that the master will receive data from the slave. Figure 12-5. R/S Bit in First Byte MSB LSB R/S Slave address 12.3.1.3 Data Validity The data on the SDA line must be stable during the high period of the clock, and the data line can only change when SCL is Low (see Figure 12-6 on page 404). Figure 12-6. Data Validity During Bit Transfer on the I2C Bus SDA SCL 12.3.1.4 Data line Change stable of data allowed Acknowledge All bus transactions have a required acknowledge clock cycle that is generated by the master. During the acknowledge cycle, the transmitter (which can be the master or slave) releases the SDA line. To acknowledge the transaction, the receiver must pull down SDA during the acknowledge clock cycle. The data sent out by the receiver during the acknowledge cycle must comply with the data validity requirements described in “Data Validity” on page 404. When a slave receiver does not acknowledge the slave address, SDA must be left High by the slave so that the master can generate a STOP condition and abort the current transfer. If the master device is acting as a receiver during a transfer, it is responsible for acknowledging each transfer made by the slave. Since the master controls the number of bytes in the transfer, it signals the end of data to the slave transmitter by not generating an acknowledge on the last data byte. The slave transmitter must then release SDA to allow the master to generate the STOP or a repeated START condition. 12.3.1.5 Arbitration A master may start a transfer only if the bus is idle. It's possible for two or more masters to generate a START condition within minimum hold time of the START condition. In these situations, an 404 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller arbitration scheme takes place on the SDA line, while SCL is High. During arbitration, the first of the competing master devices to place a '1' (High) on SDA while another master transmits a '0' (Low) will switch off its data output stage and retire until the bus is idle again. Arbitration can take place over several bits. Its first stage is a comparison of address bits, and if both masters are trying to address the same device, arbitration continues on to the comparison of data bits. 12.3.2 Available Speed Modes The I2C clock rate is determined by the parameters: CLK_PRD, TIMER_PRD, SCL_LP, and SCL_HP. where: CLK_PRD is the system clock period SCL_LP is the low phase of SCL (fixed at 6) SCL_HP is the high phase of SCL (fixed at 4) TIMER_PRD is the programmed value in the I2C Master Timer Period (I2CMTPR) register (see page 423). The I2C clock period is calculated as follows: SCL_PERIOD = 2*(1 + TIMER_PRD)*(SCL_LP + SCL_HP)*CLK_PRD For example: CLK_PRD = 50 ns TIMER_PRD = 2 SCL_LP=6 SCL_HP=4 yields a SCL frequency of: 1/T = 333 Khz Table 12-2 on page 405 gives examples of timer period, system clock, and speed mode (Standard or Fast). Table 12-2. Examples of I2C Master Timer Period versus Speed Mode System Clock Timer Period Standard Mode Timer Period Fast Mode 4 MHz 0x01 100 Kbps - - 6 MHz 0x02 100 Kbps - - 12.5 MHz 0x06 89 Kbps 0x01 312 Kbps 16.7 MHz 0x08 93 Kbps 0x02 278 Kbps 20 MHz 0x09 100 Kbps 0x02 333 Kbps 25 MHz 0x0C 96.2 Kbps 0x03 312 Kbps 33 MHz 0x10 97.1 Kbps 0x04 330 Kbps 40 MHz 0x13 100 Kbps 0x04 400 Kbps 50 MHz 0x18 100 Kbps 0x06 357 Kbps July 14, 2014 405 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface 12.3.3 Interrupts The I2C can generate interrupts when the following conditions are observed: ■ Master transaction completed ■ Master arbitration lost ■ Master transaction error ■ Slave transaction received ■ Slave transaction requested There is a separate interrupt signal for the I2C master and I2C slave modules. While both modules can generate interrupts for multiple conditions, only a single interrupt signal is sent to the interrupt controller. 12.3.3.1 I2C Master Interrupts The I2C master module generates an interrupt when a transaction completes (either transmit or receive), when arbitration is lost, or when an error occurs during a transaction. To enable the I2C master interrupt, software must set the IM bit in the I2C Master Interrupt Mask (I2CMIMR) register. When an interrupt condition is met, software must check the ERROR and ARBLST bits in the I2C Master Control/Status (I2CMCS) register to verify that an error didn't occur during the last transaction and to ensure that arbitration has not been lost. An error condition is asserted if the last transaction wasn't acknowledged by the slave. If an error is not detected and the master has not lost arbitration, the application can proceed with the transfer. The interrupt is cleared by writing a 1 to the IC bit in the I2C Master Interrupt Clear (I2CMICR) register. If the application doesn't require the use of interrupts, the raw interrupt status is always visible via the I2C Master Raw Interrupt Status (I2CMRIS) register. 12.3.3.2 I2C Slave Interrupts The slave module can generate an interrupt when data has been received or requested. This interrupt is enabled by writing a 1 to the DATAIM bit in the I2C Slave Interrupt Mask (I2CSIMR) register. Software determines whether the module should write (transmit) or read (receive) data from the I2C Slave Data (I2CSDR) register, by checking the RREQ and TREQ bits of the I2C Slave Control/Status (I2CSCSR) register. If the slave module is in receive mode and the first byte of a transfer is received, the FBR bit is set along with the RREQ bit. The interrupt is cleared by writing a 1 to the DATAIC bit in the I2C Slave Interrupt Clear (I2CSICR) register. If the application doesn't require the use of interrupts, the raw interrupt status is always visible via the I2C Slave Raw Interrupt Status (I2CSRIS) register. 12.3.4 Loopback Operation The I2C modules can be placed into an internal loopback mode for diagnostic or debug work. This is accomplished by setting the LPBK bit in the I2C Master Configuration (I2CMCR) register. In loopback mode, the SDA and SCL signals from the master and slave modules are tied together. 12.3.5 Command Sequence Flow Charts This section details the steps required to perform the various I2C transfer types in both master and slave mode. 406 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 12.3.5.1 I2C Master Command Sequences The figures that follow show the command sequences available for the I2C master. July 14, 2014 407 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Figure 12-7. Master Single SEND Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Write data to I2CMDR Read I2CMCS NO BUSBSY bit=0? YES Write ---0-111 to I2CMCS Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Idle 408 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 12-8. Master Single RECEIVE Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS NO BUSBSY bit=0? YES Write ---00111 to I2CMCS Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Read data from I2CMDR Idle July 14, 2014 409 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Figure 12-9. Master Burst SEND Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS Write data to I2CMDR BUSY bit=0? YES Read I2CMCS ERROR bit=0? NO NO NO BUSBSY bit=0? YES Write data to I2CMDR YES Write ---0-011 to I2CMCS NO ARBLST bit=1? YES Write ---0-001 to I2CMCS NO Index=n? YES Write ---0-101 to I2CMCS Write ---0-100 to I2CMCS Error Service Idle Read I2CMCS NO BUSY bit=0? YES Error Service NO ERROR bit=0? YES Idle 410 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 12-10. Master Burst RECEIVE Idle Write Slave Address to I2CMSA Sequence may be omitted in a Single Master system Read I2CMCS BUSY bit=0? Read I2CMCS NO YES NO BUSBSY bit=0? ERROR bit=0? NO YES Write ---01011 to I2CMCS NO Read data from I2CMDR ARBLST bit=1? YES Write ---01001 to I2CMCS NO Write ---0-100 to I2CMCS Index=m-1? Error Service YES Write ---00101 to I2CMCS Idle Read I2CMCS BUSY bit=0? NO YES NO ERROR bit=0? YES Error Service Read data from I2CMDR Idle July 14, 2014 411 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Figure 12-11. Master Burst RECEIVE after Burst SEND Idle Master operates in Master Transmit mode STOP condition is not generated Write Slave Address to I2CMSA Write ---01011 to I2CMCS Master operates in Master Receive mode Repeated START condition is generated with changing data direction Idle 412 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 12-12. Master Burst SEND after Burst RECEIVE Idle Master operates in Master Receive mode STOP condition is not generated Write Slave Address to I2CMSA Write ---0-011 to I2CMCS Master operates in Master Transmit mode Repeated START condition is generated with changing data direction Idle 12.3.5.2 I2C Slave Command Sequences Figure 12-13 on page 414 presents the command sequence available for the I2C slave. July 14, 2014 413 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Figure 12-13. Slave Command Sequence Idle Write OWN Slave Address to I2CSOAR Write -------1 to I2CSCSR Read I2CSCSR NO TREQ bit=1? YES Write data to I2CSDR 12.4 NO RREQ bit=1? FBR is also valid YES Read data from I2CSDR Initialization and Configuration The following example shows how to configure the I2C module to send a single byte as a master. This assumes the system clock is 20 MHz. 1. Enable the I2C clock by writing a value of 0x0000.1000 to the RCGC1 register in the System Control module. 2. Enable the clock to the appropriate GPIO module via the RCGC2 register in the System Control module. 3. In the GPIO module, enable the appropriate pins for their alternate function using the GPIOAFSEL register. Also, be sure to enable the same pins for Open Drain operation. 4. Initialize the I2C Master by writing the I2CMCR register with a value of 0x0000.0020. 5. Set the desired SCL clock speed of 100 Kbps by writing the I2CMTPR register with the correct value. The value written to the I2CMTPR register represents the number of system clock periods in one SCL clock period. The TPR value is determined by the following equation: 414 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller TPR = (System Clock / (2 * (SCL_LP + SCL_HP) * SCL_CLK)) - 1; TPR = (20MHz / (2 * (6 + 4) * 100000)) - 1; TPR = 9 Write the I2CMTPR register with the value of 0x0000.0009. 6. Specify the slave address of the master and that the next operation will be a Send by writing the I2CMSA register with a value of 0x0000.0076. This sets the slave address to 0x3B. 7. Place data (byte) to be sent in the data register by writing the I2CMDR register with the desired data. 8. Initiate a single byte send of the data from Master to Slave by writing the I2CMCS register with a value of 0x0000.0007 (STOP, START, RUN). 9. Wait until the transmission completes by polling the I2CMCS register’s BUSBSY bit until it has been cleared. 12.5 Register Map Table 12-3 on page 415 lists the I2C registers. All addresses given are relative to the I2C base addresses for the master and slave: ■ I2C 0: 0x4002.0000 Note that the I2C module clock must be enabled before the registers can be programmed (see page 190). There must be a delay of 3 system clocks after the I2C module clock is enabled before any I2C module registers are accessed. ® The hw_i2c.h file in the StellarisWare Driver Library uses a base address of 0x800 for the I2C slave registers. Be aware when using registers with offsets between 0x800 and 0x818 that StellarisWare uses an offset between 0x000 and 0x018 with the slave base address. Table 12-3. Inter-Integrated Circuit (I2C) Interface Register Map Offset Description See page Name Type Reset 0x000 I2CMSA R/W 0x0000.0000 I2C Master Slave Address 417 0x004 I2CMCS R/W 0x0000.0000 I2C Master Control/Status 418 0x008 I2CMDR R/W 0x0000.0000 I2C Master Data 422 0x00C I2CMTPR R/W 0x0000.0001 I2C Master Timer Period 423 0x010 I2CMIMR R/W 0x0000.0000 I2C Master Interrupt Mask 424 0x014 I2CMRIS RO 0x0000.0000 I2C Master Raw Interrupt Status 425 0x018 I2CMMIS RO 0x0000.0000 I2C Master Masked Interrupt Status 426 0x01C I2CMICR WO 0x0000.0000 I2C Master Interrupt Clear 427 0x020 I2CMCR R/W 0x0000.0000 I2C Master Configuration 428 I2C Master July 14, 2014 415 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Table 12-3. Inter-Integrated Circuit (I2C) Interface Register Map (continued) Offset Description See page Name Type Reset 0x800 I2CSOAR R/W 0x0000.0000 I2C Slave Own Address 430 0x804 I2CSCSR RO 0x0000.0000 I2C Slave Control/Status 431 0x808 I2CSDR R/W 0x0000.0000 I2C Slave Data 433 0x80C I2CSIMR R/W 0x0000.0000 I2C Slave Interrupt Mask 434 0x810 I2CSRIS RO 0x0000.0000 I2C Slave Raw Interrupt Status 435 0x814 I2CSMIS RO 0x0000.0000 I2C Slave Masked Interrupt Status 436 0x818 I2CSICR WO 0x0000.0000 I2C Slave Interrupt Clear 437 I2C Slave 12.6 Register Descriptions (I2C Master) The remainder of this section lists and describes the I2C master registers, in numerical order by address offset. See also “Register Descriptions (I2C Slave)” on page 429. 416 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 1: I2C Master Slave Address (I2CMSA), offset 0x000 This register consists of eight bits: seven address bits (A6-A0), and a Receive/Send bit, which determines if the next operation is a Receive (High), or Send (Low). I2C Master Slave Address (I2CMSA) I2C 0 base: 0x4002.0000 Offset 0x000 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset SA RO 0 R/S Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:1 SA R/W 0 I2C Slave Address This field specifies bits A6 through A0 of the slave address. 0 R/S R/W 0 Receive/Send The R/S bit specifies if the next operation is a Receive (High) or Send (Low). Value Description 0 Send. 1 Receive. July 14, 2014 417 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 2: I2C Master Control/Status (I2CMCS), offset 0x004 This register accesses four control bits when written, and accesses seven status bits when read. The status register consists of seven bits, which when read determine the state of the I2C bus controller. The control register consists of four bits: the RUN, START, STOP, and ACK bits. The START bit causes the generation of the START, or REPEATED START condition. The STOP bit determines if the cycle stops at the end of the data cycle, or continues on to a burst. To generate a single send cycle, the I2C Master Slave Address (I2CMSA) register is written with the desired address, the R/S bit is set to 0, and the Control register is written with ACK=X (0 or 1), STOP=1, START=1, and RUN=1 to perform the operation and stop. When the operation is completed (or aborted due an error), the interrupt pin becomes active and the data may be read from the I2CMDR register. When the I2C module operates in Master receiver mode, the ACK bit must be set normally to logic 1. This causes the I2C bus controller to send an acknowledge automatically after each byte. This bit must be reset when the I2C bus controller requires no further data to be sent from the slave transmitter. Reads I2C Master Control/Status (I2CMCS) I2C 0 base: 0x4002.0000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 BUSBSY IDLE ARBLST ERROR BUSY RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 DATACK ADRACK RO 0 RO 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6 BUSBSY RO 0 Bus Busy This bit specifies the state of the I2C bus. If set, the bus is busy; otherwise, the bus is idle. The bit changes based on the START and STOP conditions. 5 IDLE RO 0 I2C Idle This bit specifies the I2C controller state. If set, the controller is idle; otherwise the controller is not idle. 4 ARBLST RO 0 Arbitration Lost This bit specifies the result of bus arbitration. If set, the controller lost arbitration; otherwise, the controller won arbitration. 418 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Bit/Field Name Type Reset 3 DATACK RO 0 Description Acknowledge Data This bit specifies the result of the last data operation. If set, the transmitted data was not acknowledged; otherwise, the data was acknowledged. 2 ADRACK RO 0 Acknowledge Address This bit specifies the result of the last address operation. If set, the transmitted address was not acknowledged; otherwise, the address was acknowledged. 1 ERROR RO 0 Error This bit specifies the result of the last bus operation. If set, an error occurred on the last operation; otherwise, no error was detected. The error can be from the slave address not being acknowledged or the transmit data not being acknowledged. 0 BUSY RO 0 I2C Busy This bit specifies the state of the controller. If set, the controller is busy; otherwise, the controller is idle. When the BUSY bit is set, the other status bits are not valid. Writes I2C Master Control/Status (I2CMCS) I2C 0 base: 0x4002.0000 Offset 0x004 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 15 14 13 12 11 10 9 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 23 22 21 20 19 18 17 16 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 8 7 6 5 4 3 2 1 0 ACK STOP START RUN WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 WO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:4 reserved WO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3 ACK WO 0 Data Acknowledge Enable When set, causes received data byte to be acknowledged automatically by the master. See field decoding in Table 12-4 on page 420. 2 STOP WO 0 Generate STOP When set, causes the generation of the STOP condition. See field decoding in Table 12-4 on page 420. 1 START WO 0 Generate START When set, causes the generation of a START or repeated START condition. See field decoding in Table 12-4 on page 420. July 14, 2014 419 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Bit/Field Name Type Reset 0 RUN WO 0 Description I2C Master Enable When set, allows the master to send or receive data. See field decoding in Table 12-4 on page 420. Table 12-4. Write Field Decoding for I2CMCS[3:0] Field (Sheet 1 of 3) Current I2CMSA[0] State R/S Idle I2CMCS[3:0] ACK STOP START RUN 1 0 X a 0 1 0 X 1 1 1 START condition followed by a SEND and STOP condition (master remains in Idle state). 1 0 0 1 1 START condition followed by RECEIVE operation with negative ACK (master goes to the Master Receive state). 1 0 1 1 1 START condition followed by RECEIVE and STOP condition (master remains in Idle state). 1 1 0 1 1 START condition followed by RECEIVE (master goes to the Master Receive state). 1 1 1 1 1 Illegal. All other combinations not listed are non-operations. Master Transmit Description START condition followed by SEND (master goes to the Master Transmit state). NOP. X X 0 0 1 SEND operation (master remains in Master Transmit state). X X 1 0 0 STOP condition (master goes to Idle state). X X 1 0 1 SEND followed by STOP condition (master goes to Idle state). 0 X 0 1 1 Repeated START condition followed by a SEND (master remains in Master Transmit state). 0 X 1 1 1 Repeated START condition followed by SEND and STOP condition (master goes to Idle state). 1 0 0 1 1 Repeated START condition followed by a RECEIVE operation with a negative ACK (master goes to Master Receive state). 1 0 1 1 1 Repeated START condition followed by a SEND and STOP condition (master goes to Idle state). 1 1 0 1 1 Repeated START condition followed by RECEIVE (master goes to Master Receive state). 1 1 1 1 1 Illegal. All other combinations not listed are non-operations. NOP. 420 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 12-4. Write Field Decoding for I2CMCS[3:0] Field (Sheet 1 of 3) (continued) Current I2CMSA[0] State R/S I2CMCS[3:0] Description ACK STOP START RUN X 0 0 0 1 RECEIVE operation with negative ACK (master remains in Master Receive state). X X 1 0 0 STOP condition (master goes to Idle state). X 0 1 0 1 RECEIVE followed by STOP condition (master goes to Idle state). X 1 0 0 1 RECEIVE operation (master remains in Master Receive state). X 1 1 0 1 Illegal. 1 0 0 1 1 Repeated START condition followed by RECEIVE operation with a negative ACK (master remains in Master Receive state). 1 0 1 1 1 Repeated START condition followed by RECEIVE and STOP condition (master goes to Idle state). 1 1 0 1 1 Repeated START condition followed by RECEIVE (master remains in Master Receive state). 0 X 0 1 1 Repeated START condition followed by SEND (master goes to Master Transmit state). 0 X 1 1 1 Repeated START condition followed by SEND and STOP condition (master goes to Idle state). Master Receive All other combinations not listed are non-operations. b NOP. a. An X in a table cell indicates the bit can be 0 or 1. b. In Master Receive mode, a STOP condition should be generated only after a Data Negative Acknowledge executed by the master or an Address Negative Acknowledge executed by the slave. July 14, 2014 421 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 3: I2C Master Data (I2CMDR), offset 0x008 Important: This register is read-sensitive. See the register description for details. This register contains the data to be transmitted when in the Master Transmit state, and the data received when in the Master Receive state. I2C Master Data (I2CMDR) I2C 0 base: 0x4002.0000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DATA RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DATA R/W 0x00 Data Transferred Data transferred during transaction. 422 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 4: I2C Master Timer Period (I2CMTPR), offset 0x00C This register specifies the period of the SCL clock. Caution – Take care not to set bit 7 when accessing this register as unpredictable behavior can occur. I2C Master Timer Period (I2CMTPR) I2C 0 base: 0x4002.0000 Offset 0x00C Type R/W, reset 0x0000.0001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 1 reserved Type Reset RO 0 RO 0 RO 0 RO 0 15 14 13 12 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 TPR RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6:0 TPR R/W 0x1 SCL Clock Period This field specifies the period of the SCL clock. SCL_PRD = 2*(1 + TPR)*(SCL_LP + SCL_HP)*CLK_PRD where: SCL_PRD is the SCL line period (I2C clock). TPR is the Timer Period register value (range of 1 to 127). SCL_LP is the SCL Low period (fixed at 6). SCL_HP is the SCL High period (fixed at 4). July 14, 2014 423 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 5: I2C Master Interrupt Mask (I2CMIMR), offset 0x010 This register controls whether a raw interrupt is promoted to a controller interrupt. I2C Master Interrupt Mask (I2CMIMR) I2C 0 base: 0x4002.0000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 IM Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 IM R/W 0 Interrupt Mask This bit controls whether a raw interrupt is promoted to a controller interrupt. If set, the interrupt is not masked and the interrupt is promoted; otherwise, the interrupt is masked. 424 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 6: I2C Master Raw Interrupt Status (I2CMRIS), offset 0x014 This register specifies whether an interrupt is pending. I2C Master Raw Interrupt Status (I2CMRIS) I2C 0 base: 0x4002.0000 Offset 0x014 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 RIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 RIS RO 0 Raw Interrupt Status This bit specifies the raw interrupt state (prior to masking) of the I2C master block. If set, an interrupt is pending; otherwise, an interrupt is not pending. July 14, 2014 425 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 7: I2C Master Masked Interrupt Status (I2CMMIS), offset 0x018 This register specifies whether an interrupt was signaled. I2C Master Masked Interrupt Status (I2CMMIS) I2C 0 base: 0x4002.0000 Offset 0x018 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 MIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 MIS RO 0 Masked Interrupt Status This bit specifies the raw interrupt state (after masking) of the I2C master block. If set, an interrupt was signaled; otherwise, an interrupt has not been generated since the bit was last cleared. 426 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: I2C Master Interrupt Clear (I2CMICR), offset 0x01C This register clears the raw interrupt. I2C Master Interrupt Clear (I2CMICR) I2C 0 base: 0x4002.0000 Offset 0x01C Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WO 0 reserved Type Reset reserved Type Reset RO 0 IC Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 IC WO 0 Interrupt Clear This bit controls the clearing of the raw interrupt. A write of 1 clears the interrupt; otherwise, a write of 0 has no affect on the interrupt state. A read of this register returns no meaningful data. July 14, 2014 427 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 9: I2C Master Configuration (I2CMCR), offset 0x020 This register configures the mode (Master or Slave) and sets the interface for test mode loopback. I2C Master Configuration (I2CMCR) I2C 0 base: 0x4002.0000 Offset 0x020 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 SFE MFE RO 0 RO 0 RO 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 reserved RO 0 RO 0 LPBK RO 0 R/W 0 Bit/Field Name Type Reset Description 31:6 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 5 SFE R/W 0 I2C Slave Function Enable This bit specifies whether the interface may operate in Slave mode. If set, Slave mode is enabled; otherwise, Slave mode is disabled. 4 MFE R/W 0 I2C Master Function Enable This bit specifies whether the interface may operate in Master mode. If set, Master mode is enabled; otherwise, Master mode is disabled and the interface clock is disabled. 3:1 reserved RO 0x00 0 LPBK R/W 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. I2C Loopback This bit specifies whether the interface is operating normally or in Loopback mode. If set, the device is put in a test mode loopback configuration; otherwise, the device operates normally. 428 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 12.7 Register Descriptions (I2C Slave) The remainder of this section lists and describes the I2C slave registers, in numerical order by address offset. See also “Register Descriptions (I2C Master)” on page 416. July 14, 2014 429 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 10: I2C Slave Own Address (I2CSOAR), offset 0x800 This register consists of seven address bits that identify the Stellaris I2C device on the I2C bus. I2C Slave Own Address (I2CSOAR) I2C 0 base: 0x4002.0000 Offset 0x800 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 15 14 13 12 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 OAR RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:7 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 6:0 OAR R/W 0x00 I2C Slave Own Address This field specifies bits A6 through A0 of the slave address. 430 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 11: I2C Slave Control/Status (I2CSCSR), offset 0x804 This register accesses one control bit when written, and three status bits when read. The read-only Status register consists of three bits: the FBR, RREQ, and TREQ bits. The First Byte Received (FBR) bit is set only after the Stellaris device detects its own slave address and receives the first data byte from the I2C master. The Receive Request (RREQ) bit indicates that the Stellaris I2C device has received a data byte from an I2C master. Read one data byte from the I2C Slave Data (I2CSDR) register to clear the RREQ bit. The Transmit Request (TREQ) bit indicates that the Stellaris I2C device is addressed as a Slave Transmitter. Write one data byte into the I2C Slave Data (I2CSDR) register to clear the TREQ bit. The write-only Control register consists of one bit: the DA bit. The DA bit enables and disables the Stellaris I2C slave operation. Reads I2C Slave Control/Status (I2CSCSR) I2C 0 base: 0x4002.0000 Offset 0x804 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 9 8 7 6 5 4 3 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 2 1 0 FBR TREQ RREQ RO 0 RO 0 RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 FBR RO 0 First Byte Received Indicates that the first byte following the slave’s own address is received. This bit is only valid when the RREQ bit is set, and is automatically cleared when data has been read from the I2CSDR register. Note: 1 TREQ RO 0 This bit is not used for slave transmit operations. Transmit Request This bit specifies the state of the I2C slave with regards to outstanding transmit requests. If set, the I2C unit has been addressed as a slave transmitter and uses clock stretching to delay the master until data has been written to the I2CSDR register. Otherwise, there is no outstanding transmit request. 0 RREQ RO 0 Receive Request This bit specifies the status of the I2C slave with regards to outstanding receive requests. If set, the I2C unit has outstanding receive data from the I2C master and uses clock stretching to delay the master until the data has been read from the I2CSDR register. Otherwise, no receive data is outstanding. July 14, 2014 431 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Writes I2C Slave Control/Status (I2CSCSR) I2C 0 base: 0x4002.0000 Offset 0x804 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 WO 0 reserved Type Reset reserved Type Reset RO 0 DA Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DA WO 0 Device Active Value Description 0 Disables the I2C slave operation. 1 Enables the I2C slave operation. Once this bit has been set, it should not be set again unless it has been cleared by writing a 0 or by a reset, otherwise transfer failures may occur. 432 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 12: I2C Slave Data (I2CSDR), offset 0x808 Important: This register is read-sensitive. See the register description for details. This register contains the data to be transmitted when in the Slave Transmit state, and the data received when in the Slave Receive state. I2C Slave Data (I2CSDR) I2C 0 base: 0x4002.0000 Offset 0x808 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 3 2 1 0 R/W 0 R/W 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 7 6 5 4 reserved Type Reset RO 0 RO 0 RO 0 RO 0 DATA RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:8 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 7:0 DATA R/W 0x0 Data for Transfer This field contains the data for transfer during a slave receive or transmit operation. July 14, 2014 433 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 13: I2C Slave Interrupt Mask (I2CSIMR), offset 0x80C This register controls whether a raw interrupt is promoted to a controller interrupt. I2C Slave Interrupt Mask (I2CSIMR) I2C 0 base: 0x4002.0000 Offset 0x80C Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 DATAIM R/W 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DATAIM R/W 0 Data Interrupt Mask This bit controls whether the raw interrupt for data received and data requested is promoted to a controller interrupt. If set, the interrupt is not masked and the interrupt is promoted; otherwise, the interrupt is masked. 434 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 14: I2C Slave Raw Interrupt Status (I2CSRIS), offset 0x810 This register specifies whether an interrupt is pending. I2C Slave Raw Interrupt Status (I2CSRIS) I2C 0 base: 0x4002.0000 Offset 0x810 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 DATARIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DATARIS RO 0 Data Raw Interrupt Status This bit specifies the raw interrupt state for data received and data requested (prior to masking) of the I2C slave block. If set, an interrupt is pending; otherwise, an interrupt is not pending. July 14, 2014 435 Texas Instruments-Production Data Inter-Integrated Circuit (I2C) Interface Register 15: I2C Slave Masked Interrupt Status (I2CSMIS), offset 0x814 This register specifies whether an interrupt was signaled. I2C Slave Masked Interrupt Status (I2CSMIS) I2C 0 base: 0x4002.0000 Offset 0x814 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 DATAMIS RO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DATAMIS RO 0 Data Masked Interrupt Status This bit specifies the interrupt state for data received and data requested (after masking) of the I2C slave block. If set, an interrupt was signaled; otherwise, an interrupt has not been generated since the bit was last cleared. 436 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 16: I2C Slave Interrupt Clear (I2CSICR), offset 0x818 This register clears the raw interrupt. A read of this register returns no meaningful data. I2C Slave Interrupt Clear (I2CSICR) I2C 0 base: 0x4002.0000 Offset 0x818 Type WO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 8 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 1 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 DATAIC WO 0 Bit/Field Name Type Reset Description 31:1 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 0 DATAIC WO 0 Data Interrupt Clear This bit controls the clearing of the raw interrupt for data received and data requested. When set, it clears the DATARIS interrupt bit; otherwise, it has no effect on the DATARIS bit value. July 14, 2014 437 Texas Instruments-Production Data Analog Comparators 13 Analog Comparators An analog comparator is a peripheral that compares two analog voltages, and provides a logical output that signals the comparison result. Note: Not all comparators have the option to drive an output pin. See the Comparator Operating Mode tables in “Functional Description” on page 440 for more information. The comparator can provide its output to a device pin, acting as a replacement for an analog comparator on the board, or it can be used to signal the application via interrupts to cause it to start capturing a sample sequence. ® The Stellaris Analog Comparators module has the following features: ■ Three independent integrated analog comparators ■ Configurable for output to drive an output pin or generate an interrupt ■ Compare external pin input to external pin input or to internal programmable voltage reference ■ Compare a test voltage against any one of these voltages – An individual external reference voltage – A shared single external reference voltage – A shared internal reference voltage 438 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 13.1 Block Diagram Figure 13-1. Analog Comparator Module Block Diagram C2- -ve input C2+ +ve input Comparator 2 output C2o +ve input (alternate) ACCTL2 ACSTAT2 interrupt reference input C1- -ve input C1+ +ve input Comparator 1 output C1o +ve input (alternate) ACCTL1 ACSTAT1 interrupt reference input C0- -ve input C0+ +ve input Comparator 0 output C0o +ve input (alternate) ACCTL0 ACSTAT0 interrupt reference input Voltage Ref Interrupt Control ACRIS ACREFCTL internal bus ACMIS ACINTEN interrupt 13.2 Signal Description Table 13-1 on page 439 lists the external signals of the Analog Comparators and describes the function of each. The Analog Comparator output signals are alternate functions for some GPIO signals and default to be GPIO signals at reset. The column in the table below titled "Pin Assignment" lists the possible GPIO pin placements for the Analog Comparator signals. The AFSEL bit in the GPIO Alternate Function Select (GPIOAFSEL) register (page 241) should be set to choose the Analog Comparator function. The positive and negative input signals are configured by clearing the DEN bit in the GPIO Digital Enable (GPIODEN) register. For more information on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 223. Table 13-1. Analog Comparators Signals (48QFP) a Pin Name Pin Number Pin Type Buffer Type Description C0+ 42 I Analog Analog comparator 0 positive input. C0- 44 I Analog Analog comparator 0 negative input. C0o 48 O TTL Analog comparator 0 output. July 14, 2014 439 Texas Instruments-Production Data Analog Comparators Table 13-1. Analog Comparators Signals (48QFP) (continued) a Pin Name Pin Number Pin Type Buffer Type Description C1+ 13 I Analog Analog comparator 1 positive input. C1- 43 I Analog Analog comparator 1 negative input. C1o 13 O TTL C2+ 12 I Analog Analog comparator 2 positive input. C2- 11 I Analog Analog comparator 2 negative input. C2o 12 O TTL Analog comparator 1 output. Analog comparator 2 output. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 13.3 Functional Description Important: It is recommended that the Digital-Input enable (the GPIODEN bit in the GPIO module) for the analog input pin be disabled to prevent excessive current draw from the I/O pads. The comparator compares the VIN- and VIN+ inputs to produce an output, VOUT. VIN- < VIN+, VOUT = 1 VIN- > VIN+, VOUT = 0 As shown in Figure 13-2 on page 440, the input source for VIN- is an external input. In addition to an external input, input sources for VIN+ can be the +ve input of comparator 0 or an internal reference. Figure 13-2. Structure of Comparator Unit -ve input 0 output CINV 1 IntGen +ve input (alternate) reference input 2 internal bus ACCTL ACSTAT interrupt +ve input A comparator is configured through two status/control registers (ACCTL and ACSTAT ). The internal reference is configured through one control register (ACREFCTL). Interrupt status and control is configured through three registers (ACMIS, ACRIS, and ACINTEN). The operating modes of the comparators are shown in the Comparator Operating Mode tables. Typically, the comparator output is used internally to generate controller interrupts. It may also be used to drive an external pin. 440 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Important: The ASRCP bits in the ACCTLn register must be set before using the analog comparators. The proper pad configuration for the comparator input and output pins are described in the Comparator Operating Mode tables. Table 13-2. Comparator 0 Operating Modes ACCTL0 Comparator 0 ASRCP VIN- VIN+ Output Interrupt 00 C0- C0+ C0o yes 01 C0- C0+ C0o yes 10 C0- Vref C0o yes 11 C0- reserved C0o yes Table 13-3. Comparator 1 Operating Modes ACCTL1 Comparator 1 ASRCP VIN- VIN+ Output a Interrupt 00 C1- C1+/C1o C1o/C1+ yes 01 C1- C0+ C1o/C1+ yes 10 C1- Vref C1o/C1+ yes 11 C1- reserved C1o/C1+ yes a. C1o and C1+ signals share a single pin and may only be used as one or the other. Table 13-4. Comparator 2 Operating Modes ACCTL2 Comparator 2 ASRCP VIN- VIN+ Output a Interrupt 00 C2- C2+/C2o C2o/C2+ yes 01 C2- C0+ C2o/C2+ yes 10 C2- Vref C2o/C2+ yes 11 C2- reserved C2o/C2+ yes a. C2o and C2+ signals share a single pin and may only be used as one or the other. 13.3.1 Internal Reference Programming The structure of the internal reference is shown in Figure 13-3 on page 442. This is controlled by a single configuration register (ACREFCTL). Table 13-5 on page 442 shows the programming options to develop specific internal reference values, to compare an external voltage against a particular voltage generated internally. July 14, 2014 441 Texas Instruments-Production Data Analog Comparators Figure 13-3. Comparator Internal Reference Structure 8R AVDD 8R R R R ••• EN 15 14 ••• 1 0 Decoder VREF internal reference RNG Table 13-5. Internal Reference Voltage and ACREFCTL Field Values ACREFCTL Register EN Bit Value EN=0 EN=1 RNG Bit Value Output Reference Voltage Based on VREF Field Value RNG=X 0 V (GND) for any value of VREF; however, it is recommended that RNG=1 and VREF=0 for the least noisy ground reference. RNG=0 Total resistance in ladder is 31 R. The range of internal reference in this mode is 0.85-2.448 V. RNG=1 Total resistance in ladder is 23 R. The range of internal reference for this mode is 0-2.152 V. 13.4 Initialization and Configuration The following example shows how to configure an analog comparator to read back its output value from an internal register. 1. Enable the analog comparator 0 clock by writing a value of 0x0010.0000 to the RCGC1 register in the System Control module. 2. In the GPIO module, enable the GPIO port/pin associated with C0- as a GPIO input. 3. Configure the internal voltage reference to 1.65 V by writing the ACREFCTL register with the value 0x0000.030C. 442 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 4. Configure comparator 0 to use the internal voltage reference and to not invert the output by writing the ACCTL0 register with the value of 0x0000.040C. 5. Delay for some time. 6. Read the comparator output value by reading the ACSTAT0 register’s OVAL value. Change the level of the signal input on C0- to see the OVAL value change. 13.5 Register Map Table 13-6 on page 443 lists the comparator registers. The offset listed is a hexadecimal increment to the register’s address, relative to the Analog Comparator base address of 0x4003.C000. Note that the analog comparator module clock must be enabled before the registers can be programmed (see page 190). There must be a delay of 3 system clocks after the ADC module clock is enabled before any ADC module registers are accessed. Table 13-6. Analog Comparators Register Map Name Type Reset 0x000 ACMIS R/W1C 0x0000.0000 Analog Comparator Masked Interrupt Status 444 0x004 ACRIS RO 0x0000.0000 Analog Comparator Raw Interrupt Status 445 0x008 ACINTEN R/W 0x0000.0000 Analog Comparator Interrupt Enable 446 0x010 ACREFCTL R/W 0x0000.0000 Analog Comparator Reference Voltage Control 447 0x020 ACSTAT0 RO 0x0000.0000 Analog Comparator Status 0 448 0x024 ACCTL0 R/W 0x0000.0000 Analog Comparator Control 0 449 0x040 ACSTAT1 RO 0x0000.0000 Analog Comparator Status 1 448 0x044 ACCTL1 R/W 0x0000.0000 Analog Comparator Control 1 449 0x060 ACSTAT2 RO 0x0000.0000 Analog Comparator Status 2 448 0x064 ACCTL2 R/W 0x0000.0000 Analog Comparator Control 2 449 13.6 Description See page Offset Register Descriptions The remainder of this section lists and describes the Analog Comparator registers, in numerical order by address offset. July 14, 2014 443 Texas Instruments-Production Data Analog Comparators Register 1: Analog Comparator Masked Interrupt Status (ACMIS), offset 0x000 This register provides a summary of the interrupt status (masked) of the comparator. Analog Comparator Masked Interrupt Status (ACMIS) Base 0x4003.C000 Offset 0x000 Type R/W1C, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W1C 0 R/W1C 0 R/W1C 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 IN2 R/W1C 0 Comparator 2 Masked Interrupt Status Gives the masked interrupt state of this interrupt. Write 1 to this bit to clear the pending interrupt. 1 IN1 R/W1C 0 Comparator 1 Masked Interrupt Status Gives the masked interrupt state of this interrupt. Write 1 to this bit to clear the pending interrupt. 0 IN0 R/W1C 0 Comparator 0 Masked Interrupt Status Gives the masked interrupt state of this interrupt. Write 1 to this bit to clear the pending interrupt. 444 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 2: Analog Comparator Raw Interrupt Status (ACRIS), offset 0x004 This register provides a summary of the interrupt status (raw) of the comparator. Analog Comparator Raw Interrupt Status (ACRIS) Base 0x4003.C000 Offset 0x004 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 IN2 RO 0 Comparator 2 Interrupt Status When set, indicates that an interrupt has been generated by comparator 2. 1 IN1 RO 0 Comparator 1 Interrupt Status When set, indicates that an interrupt has been generated by comparator 1. 0 IN0 RO 0 Comparator 0 Interrupt Status When set, indicates that an interrupt has been generated by comparator 0. July 14, 2014 445 Texas Instruments-Production Data Analog Comparators Register 3: Analog Comparator Interrupt Enable (ACINTEN), offset 0x008 This register provides the interrupt enable for the comparator. Analog Comparator Interrupt Enable (ACINTEN) Base 0x4003.C000 Offset 0x008 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 IN2 IN1 IN0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 R/W 0 reserved Type Reset reserved Type Reset RO 0 Bit/Field Name Type Reset Description 31:3 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 2 IN2 R/W 0 Comparator 2 Interrupt Enable When set, enables the controller interrupt from the comparator 2 output 1 IN1 R/W 0 Comparator 1 Interrupt Enable When set, enables the controller interrupt from the comparator 1 output. 0 IN0 R/W 0 Comparator 0 Interrupt Enable When set, enables the controller interrupt from the comparator 0 output. 446 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 4: Analog Comparator Reference Voltage Control (ACREFCTL), offset 0x010 This register specifies whether the resistor ladder is powered on as well as the range and tap. Analog Comparator Reference Voltage Control (ACREFCTL) Base 0x4003.C000 Offset 0x010 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RO 0 RO 0 1 0 R/W 0 R/W 0 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 reserved Type Reset RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 7 6 5 4 3 2 9 8 EN RNG R/W 0 R/W 0 reserved RO 0 RO 0 RO 0 VREF RO 0 R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:10 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 9 EN R/W 0 Resistor Ladder Enable The EN bit specifies whether the resistor ladder is powered on. If 0, the resistor ladder is unpowered. If 1, the resistor ladder is connected to the analog VDD. This bit is reset to 0 so that the internal reference consumes the least amount of power if not used and programmed. 8 RNG R/W 0 Resistor Ladder Range The RNG bit specifies the range of the resistor ladder. If 0, the resistor ladder has a total resistance of 31 R. If 1, the resistor ladder has a total resistance of 23 R. 7:4 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 3:0 VREF R/W 0x00 Resistor Ladder Voltage Ref The VREF bit field specifies the resistor ladder tap that is passed through an analog multiplexer. The voltage corresponding to the tap position is the internal reference voltage available for comparison. See Table 13-5 on page 442 for some output reference voltage examples. July 14, 2014 447 Texas Instruments-Production Data Analog Comparators Register 5: Analog Comparator Status 0 (ACSTAT0), offset 0x020 Register 6: Analog Comparator Status 1 (ACSTAT1), offset 0x040 Register 7: Analog Comparator Status 2 (ACSTAT2), offset 0x060 These registers specify the current output value of the comparator. Analog Comparator Status 0 (ACSTAT0) Base 0x4003.C000 Offset 0x020 Type RO, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 OVAL reserved RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 reserved Type Reset reserved Type Reset Bit/Field Name Type Reset Description 31:2 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 1 OVAL RO 0 Comparator Output Value The OVAL bit specifies the current output value of the comparator. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 448 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Register 8: Analog Comparator Control 0 (ACCTL0), offset 0x024 Register 9: Analog Comparator Control 1 (ACCTL1), offset 0x044 Register 10: Analog Comparator Control 2 (ACCTL2), offset 0x064 These registers configure the comparator’s input and output. Analog Comparator Control 0 (ACCTL0) Base 0x4003.C000 Offset 0x024 Type R/W, reset 0x0000.0000 31 30 29 28 27 26 25 24 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 15 14 13 12 11 10 9 RO 0 RO 0 RO 0 RO 0 R/W 0 R/W 0 23 22 21 20 19 18 17 16 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 RO 0 8 7 6 5 4 3 2 1 0 CINV reserved RO 0 RO 0 RO 0 RO 0 R/W 0 RO 0 reserved Type Reset reserved Type Reset RO 0 ASRCP reserved ISLVAL R/W 0 ISEN R/W 0 R/W 0 Bit/Field Name Type Reset Description 31:11 reserved RO 0x00 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 10:9 ASRCP R/W 0x00 Analog Source Positive The ASRCP field specifies the source of input voltage to the VIN+ terminal of the comparator. The encodings for this field are as follows: Value Function 0x0 Pin value 0x1 Pin value of C0+ 0x2 Internal voltage reference 0x3 Reserved 8:5 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 4 ISLVAL R/W 0 Interrupt Sense Level Value The ISLVAL bit specifies the sense value of the input that generates an interrupt if in Level Sense mode. If 0, an interrupt is generated if the comparator output is Low. Otherwise, an interrupt is generated if the comparator output is High. July 14, 2014 449 Texas Instruments-Production Data Analog Comparators Bit/Field Name Type Reset 3:2 ISEN R/W 0x0 Description Interrupt Sense The ISEN field specifies the sense of the comparator output that generates an interrupt. The sense conditioning is as follows: Value Function 1 CINV R/W 0 0x0 Level sense, see ISLVAL 0x1 Falling edge 0x2 Rising edge 0x3 Either edge Comparator Output Invert The CINV bit conditionally inverts the output of the comparator. If 0, the output of the comparator is unchanged. If 1, the output of the comparator is inverted prior to being processed by hardware. 0 reserved RO 0 Software should not rely on the value of a reserved bit. To provide compatibility with future products, the value of a reserved bit should be preserved across a read-modify-write operation. 450 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 14 Pin Diagram The LM3S600 microcontroller pin diagrams are shown below. Figure 14-1. 48-Pin QFP Package Pin Diagram July 14, 2014 451 Texas Instruments-Production Data Signal Tables 15 Signal Tables Important: All multiplexed pins are GPIOs by default, with the exception of the five JTAG pins (PB7 and PC[3:0]) which default to the JTAG functionality. The following tables list the signals available for each pin. Functionality is enabled by software with the GPIOAFSEL register. All digital inputs are Schmitt triggered. ■ ■ ■ ■ ■ 15.1 Signals by Pin Number Signals by Signal Name Signals by Function, Except for GPIO GPIO Pins and Alternate Functions Connections for Unused Signals Signals by Pin Number Table 15-1. Signals by Pin Number Pin Number a Pin Name Pin Type Buffer Type Description PE5 I/O TTL GPIO port E bit 5. CCP5 I/O TTL Capture/Compare/PWM 5. PE4 I/O TTL GPIO port E bit 4. CCP3 I/O TTL Capture/Compare/PWM 3. PE3 I/O TTL GPIO port E bit 3. CCP1 I/O TTL Capture/Compare/PWM 1. PE2 I/O TTL GPIO port E bit 2. CCP4 I/O TTL Capture/Compare/PWM 4. System reset input. 1 2 3 4 RST I TTL LDO - Power Low drop-out regulator output voltage. This pin requires an external capacitor between the pin and GND of 1 µF or greater. 7 VDD - Power Positive supply for I/O and some logic. 8 GND - Power Ground reference for logic and I/O pins. 9 OSC0 I Analog Main oscillator crystal input or an external clock reference input. OSC1 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. PC7 I/O TTL C2- I Analog PC6 I/O TTL C2+ I Analog C2o O TTL Analog comparator 2 output. PC5 I/O TTL GPIO port C bit 5. C1+ I Analog C1o O TTL Analog comparator 1 output. 14 PC4 I/O TTL GPIO port C bit 4. 15 VDD - Power Positive supply for I/O and some logic. 16 GND - Power Ground reference for logic and I/O pins. 5 6 10 11 12 13 GPIO port C bit 7. Analog comparator 2 negative input. GPIO port C bit 6. Analog comparator 2 positive input. Analog comparator 1 positive input. 452 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 15-1. Signals by Pin Number (continued) Pin Number a Pin Name Pin Type Buffer Type Description PA0 I/O TTL GPIO port A bit 0. U0Rx I TTL UART module 0 receive. PA1 I/O TTL GPIO port A bit 1. U0Tx O TTL UART module 0 transmit. PA2 I/O TTL GPIO port A bit 2. SSIClk I/O TTL SSI clock. PA3 I/O TTL GPIO port A bit 3. SSIFss I/O TTL SSI frame. 17 18 19 20 PA4 I/O TTL GPIO port A bit 4. SSIRx I TTL SSI receive. 21 PA5 I/O TTL GPIO port A bit 5. SSITx O TTL SSI transmit. 23 VDD - Power Positive supply for I/O and some logic. 24 GND - Power Ground reference for logic and I/O pins. 25 PD0 I/O TTL GPIO port D bit 0. 26 PD1 I/O TTL GPIO port D bit 1. PD2 I/O TTL GPIO port D bit 2. U1Rx I TTL UART module 1 receive. 22 27 PD3 I/O TTL GPIO port D bit 3. U1Tx O TTL UART module 1 transmit. 29 PB0 I/O TTL GPIO port B bit 0. 30 PB1 I/O TTL GPIO port B bit 1. 31 GND - Power Ground reference for logic and I/O pins. 32 VDD - Power Positive supply for I/O and some logic. PB2 I/O TTL GPIO port B bit 2. I2CSCL I/O OD I2C clock. 28 33 PB3 I/O TTL GPIO port B bit 3. I2CSDA I/O OD I2C data. 35 PE0 I/O TTL GPIO port E bit 0. 36 PE1 I/O TTL GPIO port E bit 1. PC3 I/O TTL GPIO port C bit 3. SWO O TTL JTAG TDO and SWO. TDO O TTL JTAG TDO and SWO. PC2 I/O TTL GPIO port C bit 2. TDI I TTL JTAG TDI. PC1 I/O TTL GPIO port C bit 1. SWDIO I/O TTL JTAG TMS and SWDIO. TMS I/O TTL JTAG TMS and SWDIO. PC0 I/O TTL GPIO port C bit 0. SWCLK I TTL JTAG/SWD CLK. TCK I TTL JTAG/SWD CLK. 34 37 38 39 40 July 14, 2014 453 Texas Instruments-Production Data Signal Tables Table 15-1. Signals by Pin Number (continued) Pin Number Pin Type Buffer Type Description PB7 I/O TTL GPIO port B bit 7. TRST I TTL JTAG TRST. PB6 I/O TTL GPIO port B bit 6. C0+ I Analog PB5 I/O TTL C1- I Analog PB4 I/O TTL C0- I Analog 41 42 43 44 Analog comparator 0 positive input. GPIO port B bit 5. Analog comparator 1 negative input. GPIO port B bit 4. Analog comparator 0 negative input. PD4 I/O TTL GPIO port D bit 4. CCP0 I/O TTL Capture/Compare/PWM 0. 45 PD5 I/O TTL GPIO port D bit 5. CCP2 I/O TTL Capture/Compare/PWM 2. PD6 I/O TTL GPIO port D bit 6. PD7 I/O TTL GPIO port D bit 7. C0o O TTL Analog comparator 0 output. 46 47 a Pin Name 48 a. The TTL designation indicates the pin has TTL-compatible voltage levels. 15.2 Signals by Signal Name Table 15-2. Signals by Signal Name a Pin Name Pin Number Pin Type Buffer Type Description C0+ 42 I Analog Analog comparator 0 positive input. C0- 44 I Analog Analog comparator 0 negative input. C0o 48 O TTL C1+ 13 I Analog Analog comparator 1 positive input. C1- 43 I Analog Analog comparator 1 negative input. C1o 13 O TTL C2+ 12 I Analog Analog comparator 2 positive input. C2- 11 I Analog Analog comparator 2 negative input. C2o 12 O TTL Analog comparator 2 output. CCP0 45 I/O TTL Capture/Compare/PWM 0. CCP1 3 I/O TTL Capture/Compare/PWM 1. CCP2 46 I/O TTL Capture/Compare/PWM 2. CCP3 2 I/O TTL Capture/Compare/PWM 3. CCP4 4 I/O TTL Capture/Compare/PWM 4. CCP5 1 I/O TTL Capture/Compare/PWM 5. GND 8 16 24 31 - Power I2CSCL 33 I/O OD I2C clock. I2CSDA 34 I/O OD I2C data. Analog comparator 0 output. Analog comparator 1 output. Ground reference for logic and I/O pins. 454 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 15-2. Signals by Signal Name (continued) a Pin Name Pin Number Pin Type Buffer Type Description LDO 6 - Power Low drop-out regulator output voltage. This pin requires an external capacitor between the pin and GND of 1 µF or greater. OSC0 9 I Analog Main oscillator crystal input or an external clock reference input. OSC1 10 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. PA0 17 I/O TTL GPIO port A bit 0. PA1 18 I/O TTL GPIO port A bit 1. PA2 19 I/O TTL GPIO port A bit 2. PA3 20 I/O TTL GPIO port A bit 3. PA4 21 I/O TTL GPIO port A bit 4. PA5 22 I/O TTL GPIO port A bit 5. PB0 29 I/O TTL GPIO port B bit 0. PB1 30 I/O TTL GPIO port B bit 1. PB2 33 I/O TTL GPIO port B bit 2. PB3 34 I/O TTL GPIO port B bit 3. PB4 44 I/O TTL GPIO port B bit 4. PB5 43 I/O TTL GPIO port B bit 5. PB6 42 I/O TTL GPIO port B bit 6. PB7 41 I/O TTL GPIO port B bit 7. PC0 40 I/O TTL GPIO port C bit 0. PC1 39 I/O TTL GPIO port C bit 1. PC2 38 I/O TTL GPIO port C bit 2. PC3 37 I/O TTL GPIO port C bit 3. PC4 14 I/O TTL GPIO port C bit 4. PC5 13 I/O TTL GPIO port C bit 5. PC6 12 I/O TTL GPIO port C bit 6. PC7 11 I/O TTL GPIO port C bit 7. PD0 25 I/O TTL GPIO port D bit 0. PD1 26 I/O TTL GPIO port D bit 1. PD2 27 I/O TTL GPIO port D bit 2. PD3 28 I/O TTL GPIO port D bit 3. PD4 45 I/O TTL GPIO port D bit 4. PD5 46 I/O TTL GPIO port D bit 5. PD6 47 I/O TTL GPIO port D bit 6. PD7 48 I/O TTL GPIO port D bit 7. PE0 35 I/O TTL GPIO port E bit 0. PE1 36 I/O TTL GPIO port E bit 1. PE2 4 I/O TTL GPIO port E bit 2. PE3 3 I/O TTL GPIO port E bit 3. PE4 2 I/O TTL GPIO port E bit 4. July 14, 2014 455 Texas Instruments-Production Data Signal Tables Table 15-2. Signals by Signal Name (continued) a Pin Name Pin Number Pin Type Buffer Type Description PE5 1 I/O TTL GPIO port E bit 5. RST 5 I TTL System reset input. SSIClk 19 I/O TTL SSI clock. SSIFss 20 I/O TTL SSI frame. SSIRx 21 I TTL SSI receive. SSITx 22 O TTL SSI transmit. SWCLK 40 I TTL JTAG/SWD CLK. SWDIO 39 I/O TTL JTAG TMS and SWDIO. SWO 37 O TTL JTAG TDO and SWO. TCK 40 I TTL JTAG/SWD CLK. TDI 38 I TTL JTAG TDI. TDO 37 O TTL JTAG TDO and SWO. TMS 39 I/O TTL JTAG TMS and SWDIO. TRST 41 I TTL JTAG TRST. U0Rx 17 I TTL UART module 0 receive. U0Tx 18 O TTL UART module 0 transmit. U1Rx 27 I TTL UART module 1 receive. U1Tx 28 O TTL UART module 1 transmit. VDD 7 15 23 32 - Power Positive supply for I/O and some logic. a. The TTL designation indicates the pin has TTL-compatible voltage levels. 15.3 Signals by Function, Except for GPIO Table 15-3. Signals by Function, Except for GPIO Function Analog Comparators Pin Name a Pin Number Pin Type Buffer Type C0+ 42 I Analog Analog comparator 0 positive input. C0- 44 I Analog Analog comparator 0 negative input. C0o 48 O TTL C1+ 13 I Analog Analog comparator 1 positive input. C1- 43 I Analog Analog comparator 1 negative input. C1o 13 O TTL C2+ 12 I Analog Analog comparator 2 positive input. Analog comparator 2 negative input. C2- 11 I Analog C2o 12 O TTL Description Analog comparator 0 output. Analog comparator 1 output. Analog comparator 2 output. 456 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 15-3. Signals by Function, Except for GPIO (continued) Function General-Purpose Timers Pin Name a Pin Number Pin Type Buffer Type CCP0 45 I/O TTL Capture/Compare/PWM 0. CCP1 3 I/O TTL Capture/Compare/PWM 1. CCP2 46 I/O TTL Capture/Compare/PWM 2. CCP3 2 I/O TTL Capture/Compare/PWM 3. CCP4 4 I/O TTL Capture/Compare/PWM 4. CCP5 1 I/O TTL Capture/Compare/PWM 5. I2CSCL 33 I/O OD I2C clock. I2CSDA 34 I/O OD I2C data. SWCLK 40 I TTL JTAG/SWD CLK. SWDIO 39 I/O TTL JTAG TMS and SWDIO. SWO 37 O TTL JTAG TDO and SWO. TCK 40 I TTL JTAG/SWD CLK. TDI 38 I TTL JTAG TDI. TDO 37 O TTL JTAG TDO and SWO. TMS 39 I/O TTL JTAG TMS and SWDIO. TRST 41 I TTL JTAG TRST. GND 8 16 24 31 - Power Ground reference for logic and I/O pins. LDO 6 - Power Low drop-out regulator output voltage. This pin requires an external capacitor between the pin and GND of 1 µF or greater. VDD 7 15 23 32 - Power Positive supply for I/O and some logic. SSIClk 19 I/O TTL SSI clock. SSIFss 20 I/O TTL SSI frame. SSIRx 21 I TTL SSI receive. SSITx 22 O TTL SSI transmit. OSC0 9 I Analog Main oscillator crystal input or an external clock reference input. OSC1 10 O Analog Main oscillator crystal output. Leave unconnected when using a single-ended clock source. RST 5 I TTL System reset input. U0Rx 17 I TTL UART module 0 receive. U0Tx 18 O TTL UART module 0 transmit. U1Rx 27 I TTL UART module 1 receive. U1Tx 28 O TTL UART module 1 transmit. I2C JTAG/SWD/SWO Power SSI System Control & Clocks UART Description a. The TTL designation indicates the pin has TTL-compatible voltage levels. July 14, 2014 457 Texas Instruments-Production Data Signal Tables 15.4 GPIO Pins and Alternate Functions Table 15-4. GPIO Pins and Alternate Functions IO Pin Number Multiplexed Function PA0 17 U0Rx PA1 18 U0Tx PA2 19 SSIClk Multiplexed Function PA3 20 SSIFss PA4 21 SSIRx PA5 22 SSITx PB0 29 PB1 30 PB2 33 I2CSCL PB3 34 I2CSDA PB4 44 C0- PB5 43 C1- PB6 42 C0+ PB7 41 TRST PC0 40 TCK SWCLK PC1 39 TMS SWDIO PC2 38 TDI PC3 37 TDO SWO PC4 14 PC5 13 C1+ C1o PC6 12 C2+ C2o PC7 11 C2- PD0 25 PD1 26 PD2 27 U1Rx PD3 28 U1Tx PD4 45 CCP0 PD5 46 CCP2 PD6 47 PD7 48 PE0 35 PE1 36 PE2 4 CCP4 PE3 3 CCP1 PE4 2 CCP3 PE5 1 CCP5 C0o 458 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 15.5 Connections for Unused Signals Table 15-5 on page 459 show how to handle signals for functions that are not used in a particular system implementation. Two options are shown in the table: an acceptable practice and a preferred practice for reduced power consumption and improved EMC characteristics. Table 15-5. Connections for Unused Signals Function GPIO System Control Signal Name Pin Number Acceptable Practice Preferred Practice All unused GPIOs - NC GND OSC0 9 NC GND OSC1 10 NC NC RST 5 Pull up as shown in Figure 5-1 on page 152 Connect through a capacitor to GND as close to pin as possible July 14, 2014 459 Texas Instruments-Production Data Operating Characteristics 16 Operating Characteristics Table 16-1. Temperature Characteristics Characteristic Symbol Value Industrial operating temperature range TA -40 to +85 Unit °C Extended operating temperature range TA -40 to +105 °C Unpowered storage temperature range TS -65 to +150 °C Table 16-2. Thermal Characteristics Characteristic Symbol Value ΘJA 50 (48-pin QFP) Junction temperature TJ TA + (P • ΘJA) °C Maximum junction temperature TJMAX 115 °C a Thermal resistance (junction to ambient) b Unit c °C/W a. Junction to ambient thermal resistance θJA numbers are determined by a package simulator. b. Power dissipation is a function of temperature. c. TJMAX calculation is based on power consumption values and conditions as specified in “Power Specifications”. a Table 16-3. ESD Absolute Maximum Ratings Parameter Name Min Nom Max Unit VESDHBM - - 2.0 kV VESDCDM - - 1.0 kV VESDMM - - 100 V a. All Stellaris parts are ESD tested following the JEDEC standard. 460 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 17 Electrical Characteristics 17.1 DC Characteristics 17.1.1 Maximum Ratings The maximum ratings are the limits to which the device can be subjected without permanently damaging the device. Note: The device is not guaranteed to operate properly at the maximum ratings. Table 17-1. Maximum Ratings a Characteristic Supply voltage range (VDD) Input voltage Symbol Value VDD 0.0 to +3.6 V -0.3 to 5.5 V VIN Input voltage for a GPIO configured as an analog input Unit -0.3 to VDD + 0.3 V Maximum current for pins, excluding pins operating as GPIOs I 100 mA Maximum current for GPIO pins I 100 mA VNON 300 mV Maximum input voltage on a non-power pin when the microcontroller is unpowered a. Voltages are measured with respect to GND. Important: This device contains circuitry to protect the inputs against damage due to high-static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level (for example, either GND or VDD). 17.1.2 Recommended DC Operating Conditions Table 17-2. Recommended DC Operating Conditions Parameter Parameter Name Min Nom Max Unit 3.0 3.3 3.6 V VDD Supply voltage VIH High-level input voltage 2.0 - 5.0 V VIL Low-level input voltage -0.3 - 1.3 V VOH High-level output voltage 2.4 - - V VOL Low-level output voltage - - 0.4 V 2-mA Drive 2.0 - - mA 4-mA Drive 4.0 - - mA 8-mA Drive 8.0 - - mA 2-mA Drive 2.0 - - mA 4-mA Drive 4.0 - - mA 8-mA Drive 8.0 - - mA High-level source current, VOH=2.4 V IOH Low-level sink current, VOL=0.4 V IOL July 14, 2014 461 Texas Instruments-Production Data Electrical Characteristics 17.1.3 On-Chip Low Drop-Out (LDO) Regulator Characteristics Table 17-3. LDO Regulator Characteristics Parameter Parameter Name Min Nom Max Unit Programmable internal (logic) power supply output value 2.25 - 2.75 V Output voltage accuracy - 2% - % tPON Power-on time - - 100 µs tON Time on - - 200 µs tOFF Time off - - 100 µs VSTEP Step programming incremental voltage - 50 - mV CLDO External filter capacitor size for internal power supply 1.0 - 3.0 µF VLDOOUT 17.1.4 GPIO Module Characteristics Table 17-4. GPIO Module DC Characteristics Parameter Min Nom Max Unit RGPIOPU GPIO internal pull-up resistor 50 - 110 kΩ RGPIOPD GPIO internal pull-down resistor 55 - 180 kΩ - - 2 µA ILKG Parameter Name a GPIO input leakage current a. The leakage current is measured with GND or VDD applied to the corresponding pin(s). The leakage of digital port pins is measured individually. The port pin is configured as an input and the pullup/pulldown resistor is disabled. 17.1.5 Power Specifications The power measurements specified in the tables that follow are run on the core processor using SRAM with the following specifications (except as noted): ■ VDD = 3.3 V ■ Temperature = 25°C 462 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 17-5. Detailed Power Specifications Parameter Parameter Name Conditions Run mode 1 (Flash loop) LDO = 2.50 V Nom Max Unit 95 110 mA 60 75 mA 85 95 mA 50 60 mA 19 22 mA 950 1150 μA Code = while(1){} executed out of Flash Peripherals = All clock-gated ON System Clock = 50 MHz (with PLL) Run mode 2 (Flash loop) LDO = 2.50 V Code = while(1){} executed out of Flash Peripherals = All clock-gated OFF IDD_RUN System Clock = 50 MHz (with PLL) Run mode 1 (SRAM loop) LDO = 2.50 V Code = while(1){} executed in SRAM Peripherals = All clock-gated ON System Clock = 50 MHz (with PLL) Run mode 2 (SRAM loop) LDO = 2.50 V Code = while(1){} executed in SRAM Peripherals = All clock-gated OFF System Clock = 50 MHz (with PLL) IDD_SLEEP Sleep mode LDO = 2.50 V Peripherals = All clock-gated OFF System Clock = 50 MHz (with PLL) IDD_DEEPSLEEP Deep-Sleep mode LDO = 2.25 V Peripherals = All OFF System Clock = MOSC/16 17.1.6 Flash Memory Characteristics Table 17-6. Flash Memory Characteristics Parameter Min Nom Max Unit 10,000 100,000 - cycles Data retention at average operating temperature of 85˚C (industrial) or 105˚C (extended) 10 - - years TPROG Word program time 20 - - µs TERASE Page erase time 20 - - ms TME Mass erase time - - 250 ms PECYC TRET Parameter Name Number of guaranteed program/erase cycles a before failure a. A program/erase cycle is defined as switching the bits from 1-> 0 -> 1. 17.2 AC Characteristics 17.2.1 Load Conditions Unless otherwise specified, the following conditions are true for all timing measurements. Timing measurements are for 4-mA drive strength. July 14, 2014 463 Texas Instruments-Production Data Electrical Characteristics Figure 17-1. Load Conditions CL = 50 pF pin GND 17.2.2 Clocks Table 17-7. Phase Locked Loop (PLL) Characteristics Min Nom Max Unit fref_crystal Parameter Crystal reference Parameter Name 3.579545 - 8.192 MHz fref_ext External clock referencea 3.579545 - 8.192 MHz a b fpll PLL frequency - 200 - MHz TREADY PLL lock time - - 0.5 ms a. The exact value is determined by the crystal value programmed into the XTAL field of the Run-Mode Clock Configuration (RCC) register. b. PLL frequency is automatically calculated by the hardware based on the XTAL field of the RCC register. Table 17-8. Clock Characteristics Parameter 17.2.3 Min Nom Max Unit fIOSC Internal oscillator frequency Parameter Name 7 12 22 MHz fMOSC Main oscillator frequency 1 - 8 MHz tMOSC_per Main oscillator period 125 - 1000 ns fref_crystal_bypass Crystal reference using the main oscillator (PLL in BYPASS mode) 1 - 8 MHz fref_ext_bypass External clock reference (PLL in BYPASS mode) 0 - 50 MHz fsystem_clock System clock 0 - 50 MHz JTAG and Boundary Scan Table 17-9. JTAG Characteristics Parameter No. Parameter Parameter Name J1 fTCK TCK operational clock frequency J2 tTCK TCK operational clock period J3 tTCK_LOW TCK clock Low time Min Nom Max Unit 0 - 10 MHz 100 - - ns - tTCK/2 - ns J4 tTCK_HIGH TCK clock High time - tTCK/2 - ns J5 tTCK_R TCK rise time 0 - 10 ns J6 tTCK_F TCK fall time 0 - 10 ns J7 tTMS_SU TMS setup time to TCK rise 20 - - ns J8 tTMS_HLD TMS hold time from TCK rise 20 - - ns J9 tTDI_SU TDI setup time to TCK rise 25 - - ns 464 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 17-9. JTAG Characteristics (continued) Parameter No. Parameter J10 tTDI_HLD J11 t TDO_ZDV J12 t TDO_DV J13 t TDO_DVZ Parameter Name Min Nom Max Unit 25 - - ns TDI hold time from TCK rise TCK fall to Data Valid from High-Z 2-mA drive 23 35 ns 4-mA drive 15 26 ns 14 25 ns - 8-mA drive 8-mA drive with slew rate control 18 29 ns 2-mA drive 21 35 ns TCK fall to Data Valid from Data Valid 4-mA drive 14 25 ns 13 24 ns 8-mA drive with slew rate control 18 28 ns 2-mA drive 9 11 ns 7 9 ns 6 8 ns 7 9 ns - 8-mA drive 4-mA drive TCK fall to High-Z from Data Valid - 8-mA drive 8-mA drive with slew rate control J14 tTRST J15 tTRST_SU TRST assertion time 100 - - ns TRST setup time to TCK rise 10 - - ns Figure 17-2. JTAG Test Clock Input Timing J2 J3 J4 TCK J6 J5 Figure 17-3. JTAG Test Access Port (TAP) Timing TCK J7 TMS TDI J8 J8 TMS Input Valid TMS Input Valid J9 J9 J10 TDI Input Valid J11 TDO J7 J10 TDI Input Valid J12 TDO Output Valid July 14, 2014 J13 TDO Output Valid 465 Texas Instruments-Production Data Electrical Characteristics Figure 17-4. JTAG TRST Timing TCK J14 J15 TRST 17.2.4 Reset Table 17-10. Reset Characteristics Parameter No. Parameter Parameter Name R1 VTH Reset threshold R2 VBTH Brown-Out threshold R3 TPOR R4 TBOR R5 TIRPOR Internal reset timeout after POR R6 TIRBOR Internal reset timeout after BOR R7 TIRHWR Internal reset timeout after hardware reset (RST pin) R8 TIRSWR Internal reset timeout after software-initiated system reset a R9 TIRWDR Internal reset timeout after watchdog reseta Min Nom Max Unit - 2.0 - V 2.85 2.9 2.95 V Power-On Reset timeout - 10 - ms Brown-Out timeout - 500 - µs 15 - 30 ms 2.5 - 20 µs 2.9 - 29 µs 2.5 - 20 µs 2.5 - 20 µs 2.5 - 20 µs - - 100 ms a reseta R10 TIRLDOR Internal reset timeout after LDO R11 TVDDRISE Supply voltage (VDD) rise time (0 V-3.3 V) a. 20 * t MOSC_per Figure 17-5. External Reset Timing (RST) RST R7 /Reset (Internal) 466 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Figure 17-6. Power-On Reset Timing R1 VDD R3 /POR (Internal) R5 /Reset (Internal) Figure 17-7. Brown-Out Reset Timing R2 VDD R4 /BOR (Internal) R6 /Reset (Internal) Figure 17-8. Software Reset Timing SW Reset R8 /Reset (Internal) July 14, 2014 467 Texas Instruments-Production Data Electrical Characteristics Figure 17-9. Watchdog Reset Timing WDOG Reset (Internal) R9 /Reset (Internal) Figure 17-10. LDO Reset Timing LDO Reset (Internal) R10 /Reset (Internal) 17.2.5 Sleep Modes a Table 17-11. Sleep Modes AC Characteristics Parameter No Parameter D1 tWAKE_S D2 tWAKE_PLL_S Parameter Name Min Nom Max Unit Time to wake from interrupt in sleep or deep-sleep mode, not using the PLL - - 7 system clocks Time to wake from interrupt in sleep or deep-sleep mode when using the PLL - - TREADY ms Nom Max Unit 17 26 ns 9 13 ns 6 9 ns 8-mA drive with slew rate control 10 12 ns 2-mA drive 17 25 ns 4-mA drive 8 12 ns 6 10 ns 11 13 ns a. Values in this table assume the IOSC is the clock source during sleep or deep-sleep mode. 17.2.6 General-Purpose I/O (GPIO) Note: All GPIOs are 5 V-tolerant. Table 17-12. GPIO Characteristics Parameter Parameter Name Condition Min 2-mA drive tGPIOR tGPIOF GPIO Rise Time (from 20% to 80% of VDD) GPIO Fall Time (from 80% to 20% of VDD) 4-mA drive 8-mA drive 8-mA drive - - 8-mA drive with slew rate control 468 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 17.2.7 Synchronous Serial Interface (SSI) Table 17-13. SSI Characteristics Parameter No. Parameter Parameter Name Min S1 tclk_per SSIClk cycle time S2 tclk_high SSIClk high time S3 tclk_low SSIClk low time a Nom Max Unit 2 - 65024 system clocks - 0.5 - t clk_per - 0.5 - t clk_per S4 tclkrf SSIClk rise/fall time - 6 10 ns S5 tDMd Data from master valid delay time 0 - 1 system clocks S6 tDMs Data from master setup time 1 - - system clocks S7 tDMh Data from master hold time 2 - - system clocks S8 tDSs Data from slave setup time 1 - - system clocks S9 tDSh Data from slave hold time 2 - - system clocks a. Note that the delays shown are using 8-mA drive strength. Figure 17-11. SSI Timing for TI Frame Format (FRF=01), Single Transfer Timing Measurement S1 S2 S4 SSIClk S3 SSIFss SSITx SSIRx MSB LSB 4 to 16 bits July 14, 2014 469 Texas Instruments-Production Data Electrical Characteristics Figure 17-12. SSI Timing for MICROWIRE Frame Format (FRF=10), Single Transfer S2 S1 SSIClk S3 SSIFss SSITx MSB LSB 8-bit control SSIRx 0 MSB LSB 4 to 16 bits output data Figure 17-13. SSI Timing for SPI Frame Format (FRF=00), with SPH=1 S1 S4 S2 SSIClk (SPO=0) S3 SSIClk (SPO=1) S6 SSITx (master) S7 MSB S5 SSIRx (slave) S8 LSB S9 MSB LSB SSIFss 17.2.8 Inter-Integrated Circuit (I2C) Interface Table 17-14. I2C Characteristics Parameter No. Parameter Parameter Name Min Nom Max Unit a tSCH Start condition hold time 36 - - system clocks a tLP Clock Low period 36 - - system clocks b tSRT I2CSCL/I2CSDA rise time (VIL =0.5 V to V IH =2.4 V) - - (see note b) ns I1 I2 I3 470 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Table 17-14. I2C Characteristics (continued) Parameter No. Parameter Parameter Name Min Nom Max Unit a tDH Data hold time 2 - - system clocks c tSFT I2CSCL/I2CSDA fall time (VIH =2.4 V to V IL =0.5 V) - 9 10 ns a tHT Clock High time 24 - - system clocks a tDS Data setup time 18 - - system clocks a tSCSR Start condition setup time (for repeated start condition only) 36 - - system clocks a tSCS Stop condition setup time 24 - - system clocks I4 I5 I6 I7 I8 I9 a. Values depend on the value programmed into the TPR bit in the I2C Master Timer Period (I2CMTPR) register; a TPR programmed for the maximum I2CSCL frequency (TPR=0x2) results in a minimum output timing as shown in the table above. The I 2C interface is designed to scale the actual data transition time to move it to the middle of the I2CSCL Low period. The actual position is affected by the value programmed into the TPR; however, the numbers given in the above values are minimum values. b. Because I2CSCL and I2CSDA are open-drain-type outputs, which the controller can only actively drive Low, the time I2CSCL or I2CSDA takes to reach a high level depends on external signal capacitance and pull-up resistor values. c. Specified at a nominal 50 pF load. Figure 17-14. I2C Timing I2 I5 I6 I2CSCL I1 I4 I7 I8 I3 I9 I2CSDA 17.2.9 Analog Comparator Table 17-15. Analog Comparator Characteristics Parameter Parameter Name Min Nom Max Unit VOS Input offset voltage - ±10 ±25 mV VCM Input common mode voltage range 0 - VDD-1.5 V CMRR Common mode rejection ratio 50 - - dB TRT Response time - - 1 µs TMC Comparator mode change to Output Valid - - 10 µs Table 17-16. Analog Comparator Voltage Reference Characteristics Parameter Min Nom Max Unit RHR Resolution high range Parameter Name - VDD/31 - LSB RLR Resolution low range - VDD/23 - LSB AHR Absolute accuracy high range - - ±1/2 LSB ALR Absolute accuracy low range - - ±1/4 LSB July 14, 2014 471 Texas Instruments-Production Data Serial Flash Loader A Serial Flash Loader A.1 Serial Flash Loader ® The Stellaris serial flash loader is a preprogrammed flash-resident utility used to download code to the flash memory of a device without the use of a debug interface. The serial flash loader uses a simple packet interface to provide synchronous communication with the device. The flash loader runs off the crystal and does not enable the PLL, so its speed is determined by the crystal used. The two serial interfaces that can be used are the UART0 and SSI0 interfaces. For simplicity, both the data format and communication protocol are identical for both serial interfaces. A.2 Interfaces Once communication with the flash loader is established via one of the serial interfaces, that interface is used until the flash loader is reset or new code takes over. For example, once you start communicating using the SSI port, communications with the flash loader via the UART are disabled until the device is reset. A.2.1 UART The Universal Asynchronous Receivers/Transmitters (UART) communication uses a fixed serial format of 8 bits of data, no parity, and 1 stop bit. The baud rate used for communication is automatically detected by the flash loader and can be any valid baud rate supported by the host and the device. The auto detection sequence requires that the baud rate should be no more than 1/32 the crystal frequency of the board that is running the serial flash loader. This is actually the same as the hardware limitation for the maximum baud rate for any UART on a Stellaris device which is calculated as follows: Max Baud Rate = System Clock Frequency / 16 In order to determine the baud rate, the serial flash loader needs to determine the relationship between its own crystal frequency and the baud rate. This is enough information for the flash loader to configure its UART to the same baud rate as the host. This automatic baud-rate detection allows the host to use any valid baud rate that it wants to communicate with the device. The method used to perform this automatic synchronization relies on the host sending the flash loader two bytes that are both 0x55. This generates a series of pulses to the flash loader that it can use to calculate the ratios needed to program the UART to match the host’s baud rate. After the host sends the pattern, it attempts to read back one byte of data from the UART. The flash loader returns the value of 0xCC to indicate successful detection of the baud rate. If this byte is not received after at least twice the time required to transfer the two bytes, the host can resend another pattern of 0x55, 0x55, and wait for the 0xCC byte again until the flash loader acknowledges that it has received a synchronization pattern correctly. For example, the time to wait for data back from the flash loader should be calculated as at least 2*(20(bits/sync)/baud rate (bits/sec)). For a baud rate of 115200, this time is 2*(20/115200) or 0.35 ms. A.2.2 SSI The Synchronous Serial Interface (SSI) port also uses a fixed serial format for communications, with the framing defined as Motorola format with SPH set to 1 and SPO set to 1. See “Frame Formats” on page 365 in the SSI chapter for more information on formats for this transfer protocol. Like the UART, this interface has hardware requirements that limit the maximum speed that the SSI clock can run. This allows the SSI clock to be at most 1/12 the crystal frequency of the board running 472 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller the flash loader. Since the host device is the master, the SSI on the flash loader device does not need to determine the clock as it is provided directly by the host. A.3 Packet Handling All communications, with the exception of the UART auto-baud, are done via defined packets that are acknowledged (ACK) or not acknowledged (NAK) by the devices. The packets use the same format for receiving and sending packets, including the method used to acknowledge successful or unsuccessful reception of a packet. A.3.1 Packet Format All packets sent and received from the device use the following byte-packed format. struct { unsigned char ucSize; unsigned char ucCheckSum; unsigned char Data[]; }; A.3.2 ucSize The first byte received holds the total size of the transfer including the size and checksum bytes. ucChecksum This holds a simple checksum of the bytes in the data buffer only. The algorithm is Data[0]+Data[1]+…+ Data[ucSize-3]. Data This is the raw data intended for the device, which is formatted in some form of command interface. There should be ucSize–2 bytes of data provided in this buffer to or from the device. Sending Packets The actual bytes of the packet can be sent individually or all at once; the only limitation is that commands that cause flash memory access should limit the download sizes to prevent losing bytes during flash programming. This limitation is discussed further in the section that describes the serial flash loader command, COMMAND_SEND_DATA (see “COMMAND_SEND_DATA (0x24)” on page 475). Once the packet has been formatted correctly by the host, it should be sent out over the UART or SSI interface. Then the host should poll the UART or SSI interface for the first non-zero data returned from the device. The first non-zero byte will either be an ACK (0xCC) or a NAK (0x33) byte from the device indicating the packet was received successfully (ACK) or unsuccessfully (NAK). This does not indicate that the actual contents of the command issued in the data portion of the packet were valid, just that the packet was received correctly. A.3.3 Receiving Packets The flash loader sends a packet of data in the same format that it receives a packet. The flash loader may transfer leading zero data before the first actual byte of data is sent out. The first non-zero byte is the size of the packet followed by a checksum byte, and finally followed by the data itself. There is no break in the data after the first non-zero byte is sent from the flash loader. Once the device communicating with the flash loader receives all the bytes, it must either ACK or NAK the packet to indicate that the transmission was successful. The appropriate response after sending a NAK to the flash loader is to resend the command that failed and request the data again. If needed, the host may send leading zeros before sending down the ACK/NAK signal to the flash loader, as the July 14, 2014 473 Texas Instruments-Production Data Serial Flash Loader flash loader only accepts the first non-zero data as a valid response. This zero padding is needed by the SSI interface in order to receive data to or from the flash loader. A.4 Commands The next section defines the list of commands that can be sent to the flash loader. The first byte of the data should always be one of the defined commands, followed by data or parameters as determined by the command that is sent. A.4.1 COMMAND_PING (0X20) This command simply accepts the command and sets the global status to success. The format of the packet is as follows: Byte[0] = 0x03; Byte[1] = checksum(Byte[2]); Byte[2] = COMMAND_PING; The ping command has 3 bytes and the value for COMMAND_PING is 0x20 and the checksum of one byte is that same byte, making Byte[1] also 0x20. Since the ping command has no real return status, the receipt of an ACK can be interpreted as a successful ping to the flash loader. A.4.2 COMMAND_GET_STATUS (0x23) This command returns the status of the last command that was issued. Typically, this command should be sent after every command to ensure that the previous command was successful or to properly respond to a failure. The command requires one byte in the data of the packet and should be followed by reading a packet with one byte of data that contains a status code. The last step is to ACK or NAK the received data so the flash loader knows that the data has been read. Byte[0] = 0x03 Byte[1] = checksum(Byte[2]) Byte[2] = COMMAND_GET_STATUS A.4.3 COMMAND_DOWNLOAD (0x21) This command is sent to the flash loader to indicate where to store data and how many bytes will be sent by the COMMAND_SEND_DATA commands that follow. The command consists of two 32-bit values that are both transferred MSB first. The first 32-bit value is the address to start programming data into, while the second is the 32-bit size of the data that will be sent. This command also triggers an erase of the full area to be programmed so this command takes longer than other commands. This results in a longer time to receive the ACK/NAK back from the board. This command should be followed by a COMMAND_GET_STATUS to ensure that the Program Address and Program size are valid for the device running the flash loader. The format of the packet to send this command is a follows: Byte[0] Byte[1] Byte[2] Byte[3] Byte[4] Byte[5] Byte[6] Byte[7] = = = = = = = = 11 checksum(Bytes[2:10]) COMMAND_DOWNLOAD Program Address [31:24] Program Address [23:16] Program Address [15:8] Program Address [7:0] Program Size [31:24] 474 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller Byte[8] = Program Size [23:16] Byte[9] = Program Size [15:8] Byte[10] = Program Size [7:0] A.4.4 COMMAND_SEND_DATA (0x24) This command should only follow a COMMAND_DOWNLOAD command or another COMMAND_SEND_DATA command if more data is needed. Consecutive send data commands automatically increment address and continue programming from the previous location. The caller should limit transfers of data to a maximum 8 bytes of packet data to allow the flash to program successfully and not overflow input buffers of the serial interfaces. The command terminates programming once the number of bytes indicated by the COMMAND_DOWNLOAD command has been received. Each time this function is called it should be followed by a COMMAND_GET_STATUS to ensure that the data was successfully programmed into the flash. If the flash loader sends a NAK to this command, the flash loader does not increment the current address to allow retransmission of the previous data. Byte[0] = 11 Byte[1] = checksum(Bytes[2:10]) Byte[2] = COMMAND_SEND_DATA Byte[3] = Data[0] Byte[4] = Data[1] Byte[5] = Data[2] Byte[6] = Data[3] Byte[7] = Data[4] Byte[8] = Data[5] Byte[9] = Data[6] Byte[10] = Data[7] A.4.5 COMMAND_RUN (0x22) This command is used to tell the flash loader to execute from the address passed as the parameter in this command. This command consists of a single 32-bit value that is interpreted as the address to execute. The 32-bit value is transmitted MSB first and the flash loader responds with an ACK signal back to the host device before actually executing the code at the given address. This allows the host to know that the command was received successfully and the code is now running. Byte[0] Byte[1] Byte[2] Byte[3] Byte[4] Byte[5] Byte[6] A.4.6 = = = = = = = 7 checksum(Bytes[2:6]) COMMAND_RUN Execute Address[31:24] Execute Address[23:16] Execute Address[15:8] Execute Address[7:0] COMMAND_RESET (0x25) This command is used to tell the flash loader device to reset. This is useful when downloading a new image that overwrote the flash loader and wants to start from a full reset. Unlike the COMMAND_RUN command, this allows the initial stack pointer to be read by the hardware and set up for the new code. It can also be used to reset the flash loader if a critical error occurs and the host device wants to restart communication with the flash loader. July 14, 2014 475 Texas Instruments-Production Data Serial Flash Loader Byte[0] = 3 Byte[1] = checksum(Byte[2]) Byte[2] = COMMAND_RESET The flash loader responds with an ACK signal back to the host device before actually executing the software reset to the device running the flash loader. This allows the host to know that the command was received successfully and the part will be reset. 476 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller B Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 The Cortex-M3 Processor R0, type R/W, , reset - (see page 47) DATA DATA R1, type R/W, , reset - (see page 47) DATA DATA R2, type R/W, , reset - (see page 47) DATA DATA R3, type R/W, , reset - (see page 47) DATA DATA R4, type R/W, , reset - (see page 47) DATA DATA R5, type R/W, , reset - (see page 47) DATA DATA R6, type R/W, , reset - (see page 47) DATA DATA R7, type R/W, , reset - (see page 47) DATA DATA R8, type R/W, , reset - (see page 47) DATA DATA R9, type R/W, , reset - (see page 47) DATA DATA R10, type R/W, , reset - (see page 47) DATA DATA R11, type R/W, , reset - (see page 47) DATA DATA R12, type R/W, , reset - (see page 47) DATA DATA SP, type R/W, , reset - (see page 48) SP SP LR, type R/W, , reset 0xFFFF.FFFF (see page 49) LINK LINK PC, type R/W, , reset - (see page 50) PC PC July 14, 2014 477 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PSR, type R/W, , reset 0x0100.0000 (see page 51) N Z C V Q ICI / IT THUMB ICI / IT ISRNUM PRIMASK, type R/W, , reset 0x0000.0000 (see page 55) PRIMASK FAULTMASK, type R/W, , reset 0x0000.0000 (see page 56) FAULTMASK BASEPRI, type R/W, , reset 0x0000.0000 (see page 57) BASEPRI CONTROL, type R/W, , reset 0x0000.0000 (see page 58) ASP TMPL INTEN ENABLE Cortex-M3 Peripherals System Timer (SysTick) Registers Base 0xE000.E000 STCTRL, type R/W, offset 0x010, reset 0x0000.0000 COUNT CLK_SRC STRELOAD, type R/W, offset 0x014, reset 0x0000.0000 RELOAD RELOAD STCURRENT, type R/WC, offset 0x018, reset 0x0000.0000 CURRENT CURRENT Cortex-M3 Peripherals Nested Vectored Interrupt Controller (NVIC) Registers Base 0xE000.E000 EN0, type R/W, offset 0x100, reset 0x0000.0000 INT INT DIS0, type R/W, offset 0x180, reset 0x0000.0000 INT INT PEND0, type R/W, offset 0x200, reset 0x0000.0000 INT INT UNPEND0, type R/W, offset 0x280, reset 0x0000.0000 INT INT ACTIVE0, type RO, offset 0x300, reset 0x0000.0000 INT INT PRI0, type R/W, offset 0x400, reset 0x0000.0000 INTD INTC INTB INTA PRI1, type R/W, offset 0x404, reset 0x0000.0000 INTD INTC INTB INTA 478 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PRI2, type R/W, offset 0x408, reset 0x0000.0000 INTD INTC INTB INTA PRI3, type R/W, offset 0x40C, reset 0x0000.0000 INTD INTC INTB INTA PRI4, type R/W, offset 0x410, reset 0x0000.0000 INTD INTC INTB INTA PRI5, type R/W, offset 0x414, reset 0x0000.0000 INTD INTC INTB INTA PRI6, type R/W, offset 0x418, reset 0x0000.0000 INTD INTC INTB INTA PRI7, type R/W, offset 0x41C, reset 0x0000.0000 INTD INTC INTB INTA SWTRIG, type WO, offset 0xF00, reset 0x0000.0000 INTID Cortex-M3 Peripherals System Control Block (SCB) Registers Base 0xE000.E000 CPUID, type RO, offset 0xD00, reset 0x410F.C231 IMP VAR CON PARTNO REV INTCTRL, type R/W, offset 0xD04, reset 0x0000.0000 NMISET PENDSV UNPENDSV VECPEND ISRPRE PENDSTSET PENDSTCLR ISRPEND VECPEND RETBASE VECACT VTABLE, type R/W, offset 0xD08, reset 0x0000.0000 BASE OFFSET OFFSET APINT, type R/W, offset 0xD0C, reset 0xFA05.0000 VECTKEY PRIGROUP ENDIANESS SYSRESREQ VECTCLRACT VECTRESET SYSCTRL, type R/W, offset 0xD10, reset 0x0000.0000 SEVONPEND SLEEPDEEP SLEEPEXIT CFGCTRL, type R/W, offset 0xD14, reset 0x0000.0000 DIV0 STKALIGN BFHFNMIGN UNALIGNED MAINPEND BASETHR SYSPRI1, type R/W, offset 0xD18, reset 0x0000.0000 USAGE BUS MEM SYSPRI2, type R/W, offset 0xD1C, reset 0x0000.0000 SVC SYSPRI3, type R/W, offset 0xD20, reset 0x0000.0000 TICK PENDSV DEBUG July 14, 2014 479 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 MON SVCA SYSHNDCTRL, type R/W, offset 0xD24, reset 0x0000.0000 USAGE SVC BUSP MEMP USAGEP TICK PNDSV USGA BUS MEM BUSA MEMA INVSTAT UNDEF DERR IERR FAULTSTAT, type R/W1C, offset 0xD28, reset 0x0000.0000 BFARV BSTKE BUSTKE IMPRE DIV0 UNALIGN PRECISE IBUS NOCP MMARV MSTKE INVPC MUSTKE HFAULTSTAT, type R/W1C, offset 0xD2C, reset 0x0000.0000 DBG FORCED VECT MMADDR, type R/W, offset 0xD34, reset ADDR ADDR FAULTADDR, type R/W, offset 0xD38, reset ADDR ADDR Cortex-M3 Peripherals Memory Protection Unit (MPU) Registers Base 0xE000.E000 MPUTYPE, type RO, offset 0xD90, reset 0x0000.0800 IREGION DREGION SEPARATE MPUCTRL, type R/W, offset 0xD94, reset 0x0000.0000 PRIVDEFEN HFNMIENA ENABLE MPUNUMBER, type R/W, offset 0xD98, reset 0x0000.0000 NUMBER MPUBASE, type R/W, offset 0xD9C, reset 0x0000.0000 ADDR ADDR VALID REGION VALID REGION VALID REGION VALID REGION MPUBASE1, type R/W, offset 0xDA4, reset 0x0000.0000 ADDR ADDR MPUBASE2, type R/W, offset 0xDAC, reset 0x0000.0000 ADDR ADDR MPUBASE3, type R/W, offset 0xDB4, reset 0x0000.0000 ADDR ADDR MPUATTR, type R/W, offset 0xDA0, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR1, type R/W, offset 0xDA8, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR2, type R/W, offset 0xDB0, reset 0x0000.0000 XN AP TEX SRD S C SIZE B ENABLE MPUATTR3, type R/W, offset 0xDB8, reset 0x0000.0000 XN AP SRD TEX S SIZE 480 C B ENABLE July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BORIOR BORWT System Control Base 0x400F.E000 DID0, type RO, offset 0x000, reset - (see page 162) VER MAJOR MINOR PBORCTL, type R/W, offset 0x030, reset 0x0000.7FFD (see page 164) BORTIM LDOPCTL, type R/W, offset 0x034, reset 0x0000.0000 (see page 165) VADJ RIS, type RO, offset 0x050, reset 0x0000.0000 (see page 166) PLLLRIS CLRIS IOFRIS MOFRIS LDORIS BORRIS PLLFRIS PLLLIM CLIM IOFIM MOFIM LDOIM BORIM PLLFIM PLLLMIS CLMIS IOFMIS MOFMIS LDOMIS BORMIS LDO SW WDT BOR POR IMC, type R/W, offset 0x054, reset 0x0000.0000 (see page 167) MISC, type R/W1C, offset 0x058, reset 0x0000.0000 (see page 168) RESC, type R/W, offset 0x05C, reset - (see page 169) EXT RCC, type R/W, offset 0x060, reset 0x0780.3AC0 (see page 170) ACG PWRDN OEN BYPASS SYSDIV USESYSDIV PLLVER XTAL OSCSRC IOSCVER MOSCVER IOSCDIS MOSCDIS PLLCFG, type RO, offset 0x064, reset - (see page 173) OD F R DSLPCLKCFG, type R/W, offset 0x144, reset 0x0780.0000 (see page 174) IOSC CLKVCLR, type R/W, offset 0x150, reset 0x0000.0000 (see page 175) VERCLR LDOARST, type R/W, offset 0x160, reset 0x0000.0000 (see page 176) LDOARST DID1, type RO, offset 0x004, reset - (see page 177) VER FAM PARTNO TEMP PKG ROHS QUAL DC0, type RO, offset 0x008, reset 0x001F.000F (see page 179) SRAMSZ FLASHSZ DC1, type RO, offset 0x010, reset 0x0000.309F (see page 180) MINSYSDIV MPU PLL WDT SWO SWD JTAG TIMER2 TIMER1 TIMER0 UART1 UART0 DC2, type RO, offset 0x014, reset 0x0707.1013 (see page 182) COMP2 COMP1 COMP0 I2C0 SSI0 DC3, type RO, offset 0x018, reset 0xBF00.7FC0 (see page 184) 32KHZ CCP5 C2O CCP4 C2PLUS C2MINUS CCP3 C1O CCP2 CCP1 C1PLUS C1MINUS CCP0 C0O C0PLUS C0MINUS July 14, 2014 481 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GPIOE GPIOD GPIOC GPIOB GPIOA TIMER2 TIMER1 TIMER0 UART1 UART0 TIMER1 TIMER0 UART1 UART0 TIMER1 TIMER0 UART1 UART0 DC4, type RO, offset 0x01C, reset 0x0000.001F (see page 186) RCGC0, type R/W, offset 0x100, reset 0x00000040 (see page 187) WDT SCGC0, type R/W, offset 0x110, reset 0x00000040 (see page 188) WDT DCGC0, type R/W, offset 0x120, reset 0x00000040 (see page 189) WDT RCGC1, type R/W, offset 0x104, reset 0x00000000 (see page 190) COMP2 COMP1 COMP0 I2C0 SSI0 SCGC1, type R/W, offset 0x114, reset 0x00000000 (see page 192) COMP2 COMP1 COMP0 TIMER2 I2C0 SSI0 DCGC1, type R/W, offset 0x124, reset 0x00000000 (see page 194) COMP2 COMP1 COMP0 TIMER2 I2C0 SSI0 RCGC2, type R/W, offset 0x108, reset 0x00000000 (see page 196) GPIOE GPIOD GPIOC GPIOB GPIOA GPIOE GPIOD GPIOC GPIOB GPIOA GPIOE GPIOD GPIOC GPIOB GPIOA TIMER2 TIMER1 TIMER0 UART1 UART0 SCGC2, type R/W, offset 0x118, reset 0x00000000 (see page 197) DCGC2, type R/W, offset 0x128, reset 0x00000000 (see page 199) SRCR0, type R/W, offset 0x040, reset 0x00000000 (see page 201) WDT SRCR1, type R/W, offset 0x044, reset 0x00000000 (see page 202) COMP2 COMP1 COMP0 I2C0 SSI0 SRCR2, type R/W, offset 0x048, reset 0x00000000 (see page 204) GPIOE GPIOD GPIOC GPIOB GPIOA COMT MERASE ERASE WRITE Internal Memory Flash Memory Control Registers (Flash Control Offset) Base 0x400F.D000 FMA, type R/W, offset 0x000, reset 0x0000.0000 OFFSET FMD, type R/W, offset 0x004, reset 0x0000.0000 DATA DATA FMC, type R/W, offset 0x008, reset 0x0000.0000 WRKEY 482 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PRIS ARIS PMASK AMASK PMISC AMISC FCRIS, type RO, offset 0x00C, reset 0x0000.0000 FCIM, type R/W, offset 0x010, reset 0x0000.0000 FCMISC, type R/W1C, offset 0x014, reset 0x0000.0000 Internal Memory Flash Memory Protection Registers (System Control Offset) Base 0x400F.E000 USECRL, type R/W, offset 0x140, reset 0x31 USEC FMPRE, type R/W, offset 0x130, reset 0x8000.FFFF DBG READ_ENABLE READ_ENABLE FMPPE, type R/W, offset 0x134, reset 0x0000.FFFF PROG_ENABLE PROG_ENABLE General-Purpose Input/Outputs (GPIOs) GPIO Port A base: 0x4000.4000 GPIO Port B base: 0x4000.5000 GPIO Port C base: 0x4000.6000 GPIO Port D base: 0x4000.7000 GPIO Port E base: 0x4002.4000 GPIODATA, type R/W, offset 0x000, reset 0x0000.0000 (see page 232) DATA GPIODIR, type R/W, offset 0x400, reset 0x0000.0000 (see page 233) DIR GPIOIS, type R/W, offset 0x404, reset 0x0000.0000 (see page 234) IS GPIOIBE, type R/W, offset 0x408, reset 0x0000.0000 (see page 235) IBE GPIOIEV, type R/W, offset 0x40C, reset 0x0000.0000 (see page 236) IEV GPIOIM, type R/W, offset 0x410, reset 0x0000.0000 (see page 237) IME GPIORIS, type RO, offset 0x414, reset 0x0000.0000 (see page 238) RIS GPIOMIS, type RO, offset 0x418, reset 0x0000.0000 (see page 239) MIS GPIOICR, type W1C, offset 0x41C, reset 0x0000.0000 (see page 240) IC July 14, 2014 483 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GPIOAFSEL, type R/W, offset 0x420, reset - (see page 241) AFSEL GPIODR2R, type R/W, offset 0x500, reset 0x0000.00FF (see page 243) DRV2 GPIODR4R, type R/W, offset 0x504, reset 0x0000.0000 (see page 244) DRV4 GPIODR8R, type R/W, offset 0x508, reset 0x0000.0000 (see page 245) DRV8 GPIOODR, type R/W, offset 0x50C, reset 0x0000.0000 (see page 246) ODE GPIOPUR, type R/W, offset 0x510, reset 0x0000.00FF (see page 247) PUE GPIOPDR, type R/W, offset 0x514, reset 0x0000.0000 (see page 248) PDE GPIOSLR, type R/W, offset 0x518, reset 0x0000.0000 (see page 249) SRL GPIODEN, type R/W, offset 0x51C, reset 0x0000.00FF (see page 250) DEN GPIOPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 251) PID4 GPIOPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 252) PID5 GPIOPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 253) PID6 GPIOPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 254) PID7 GPIOPeriphID0, type RO, offset 0xFE0, reset 0x0000.0061 (see page 255) PID0 GPIOPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 256) PID1 GPIOPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 257) PID2 GPIOPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 258) PID3 484 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GPIOPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 259) CID0 GPIOPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 260) CID1 GPIOPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 261) CID2 GPIOPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 262) CID3 General-Purpose Timers Timer0 base: 0x4003.0000 Timer1 base: 0x4003.1000 Timer2 base: 0x4003.2000 GPTMCFG, type R/W, offset 0x000, reset 0x0000.0000 (see page 275) GPTMCFG GPTMTAMR, type R/W, offset 0x004, reset 0x0000.0000 (see page 276) TAAMS TACMR TAMR TBAMS TBCMR TBMR GPTMTBMR, type R/W, offset 0x008, reset 0x0000.0000 (see page 278) GPTMCTL, type R/W, offset 0x00C, reset 0x0000.0000 (see page 280) TBPWML TBEVENT TBSTALL TBEN TAPWML RTCEN TAEVENT TASTALL TAEN GPTMIMR, type R/W, offset 0x018, reset 0x0000.0000 (see page 283) CBEIM CBMIM TBTOIM RTCIM CAEIM CAMIM TATOIM CBMRIS TBTORIS RTCRIS CAERIS CAMRIS TATORIS RTCMIS CAEMIS CAMMIS TATOMIS GPTMRIS, type RO, offset 0x01C, reset 0x0000.0000 (see page 285) CBERIS GPTMMIS, type RO, offset 0x020, reset 0x0000.0000 (see page 286) CBEMIS CBMMIS TBTOMIS GPTMICR, type W1C, offset 0x024, reset 0x0000.0000 (see page 287) CBECINT CBMCINT TBTOCINT RTCCINT CAECINT CAMCINT TATOCINT GPTMTAILR, type R/W, offset 0x028, reset 0xFFFF.FFFF (see page 289) TAILRH TAILRL GPTMTBILR, type R/W, offset 0x02C, reset 0x0000.FFFF (see page 290) TBILRL GPTMTAMATCHR, type R/W, offset 0x030, reset 0xFFFF.FFFF (see page 291) TAMRH TAMRL GPTMTBMATCHR, type R/W, offset 0x034, reset 0x0000.FFFF (see page 292) TBMRL July 14, 2014 485 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RESEN INTEN GPTMTAPR, type R/W, offset 0x038, reset 0x0000.0000 (see page 293) TAPSR GPTMTBPR, type R/W, offset 0x03C, reset 0x0000.0000 (see page 294) TBPSR GPTMTAPMR, type R/W, offset 0x040, reset 0x0000.0000 (see page 295) TAPSMR GPTMTBPMR, type R/W, offset 0x044, reset 0x0000.0000 (see page 296) TBPSMR GPTMTAR, type RO, offset 0x048, reset 0xFFFF.FFFF (see page 297) TARH TARL GPTMTBR, type RO, offset 0x04C, reset 0x0000.FFFF (see page 298) TBRL Watchdog Timer Base 0x4000.0000 WDTLOAD, type R/W, offset 0x000, reset 0xFFFF.FFFF (see page 303) WDTLoad WDTLoad WDTVALUE, type RO, offset 0x004, reset 0xFFFF.FFFF (see page 304) WDTValue WDTValue WDTCTL, type R/W, offset 0x008, reset 0x0000.0000 (see page 305) WDTICR, type WO, offset 0x00C, reset - (see page 306) WDTIntClr WDTIntClr WDTRIS, type RO, offset 0x010, reset 0x0000.0000 (see page 307) WDTRIS WDTMIS, type RO, offset 0x014, reset 0x0000.0000 (see page 308) WDTMIS WDTTEST, type R/W, offset 0x418, reset 0x0000.0000 (see page 309) STALL WDTLOCK, type R/W, offset 0xC00, reset 0x0000.0000 (see page 310) WDTLock WDTLock WDTPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 311) PID4 WDTPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 312) PID5 WDTPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 313) PID6 486 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 OE BE PE FE PEN BRK WDTPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 314) PID7 WDTPeriphID0, type RO, offset 0xFE0, reset 0x0000.0005 (see page 315) PID0 WDTPeriphID1, type RO, offset 0xFE4, reset 0x0000.0018 (see page 316) PID1 WDTPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 317) PID2 WDTPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 318) PID3 WDTPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 319) CID0 WDTPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 320) CID1 WDTPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 321) CID2 WDTPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 322) CID3 Universal Asynchronous Receivers/Transmitters (UARTs) UART0 base: 0x4000.C000 UART1 base: 0x4000.D000 UARTDR, type R/W, offset 0x000, reset 0x0000.0000 (see page 331) OE BE PE FE DATA UARTRSR/UARTECR, type RO, offset 0x004, reset 0x0000.0000 (Reads) (see page 333) UARTRSR/UARTECR, type WO, offset 0x004, reset 0x0000.0000 (Writes) (see page 333) DATA UARTFR, type RO, offset 0x018, reset 0x0000.0090 (see page 335) TXFE RXFF TXFF RXFE BUSY UARTIBRD, type R/W, offset 0x024, reset 0x0000.0000 (see page 337) DIVINT UARTFBRD, type R/W, offset 0x028, reset 0x0000.0000 (see page 338) DIVFRAC UARTLCRH, type R/W, offset 0x02C, reset 0x0000.0000 (see page 339) SPS WLEN July 14, 2014 FEN STP2 EPS 487 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RXE TXE LBE UARTCTL, type R/W, offset 0x030, reset 0x0000.0300 (see page 341) UARTEN UARTIFLS, type R/W, offset 0x034, reset 0x0000.0012 (see page 343) RXIFLSEL TXIFLSEL UARTIM, type R/W, offset 0x038, reset 0x0000.0000 (see page 345) OEIM BEIM PEIM FEIM RTIM TXIM RXIM PERIS FERIS RTRIS TXRIS RXRIS PEMIS FEMIS RTMIS TXMIS RXMIS PEIC FEIC RTIC TXIC RXIC UARTRIS, type RO, offset 0x03C, reset 0x0000.0000 (see page 347) OERIS BERIS UARTMIS, type RO, offset 0x040, reset 0x0000.0000 (see page 348) OEMIS BEMIS UARTICR, type W1C, offset 0x044, reset 0x0000.0000 (see page 349) OEIC BEIC UARTPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 351) PID4 UARTPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 352) PID5 UARTPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 353) PID6 UARTPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 354) PID7 UARTPeriphID0, type RO, offset 0xFE0, reset 0x0000.0011 (see page 355) PID0 UARTPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 356) PID1 UARTPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 357) PID2 UARTPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 358) PID3 UARTPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 359) CID0 UARTPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 360) CID1 UARTPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 361) CID2 488 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 UARTPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 362) CID3 Synchronous Serial Interface (SSI) SSI0 base: 0x4000.8000 SSICR0, type R/W, offset 0x000, reset 0x0000.0000 (see page 376) SCR SPH SPO FRF DSS SSICR1, type R/W, offset 0x004, reset 0x0000.0000 (see page 378) SOD MS SSE LBM RFF RNE TNF TFE TXIM RXIM RTIM RORIM TXRIS RXRIS RTRIS RORRIS TXMIS RXMIS RTMIS RORMIS RTIC RORIC SSIDR, type R/W, offset 0x008, reset 0x0000.0000 (see page 380) DATA SSISR, type RO, offset 0x00C, reset 0x0000.0003 (see page 381) BSY SSICPSR, type R/W, offset 0x010, reset 0x0000.0000 (see page 383) CPSDVSR SSIIM, type R/W, offset 0x014, reset 0x0000.0000 (see page 384) SSIRIS, type RO, offset 0x018, reset 0x0000.0008 (see page 386) SSIMIS, type RO, offset 0x01C, reset 0x0000.0000 (see page 387) SSIICR, type W1C, offset 0x020, reset 0x0000.0000 (see page 388) SSIPeriphID4, type RO, offset 0xFD0, reset 0x0000.0000 (see page 389) PID4 SSIPeriphID5, type RO, offset 0xFD4, reset 0x0000.0000 (see page 390) PID5 SSIPeriphID6, type RO, offset 0xFD8, reset 0x0000.0000 (see page 391) PID6 SSIPeriphID7, type RO, offset 0xFDC, reset 0x0000.0000 (see page 392) PID7 SSIPeriphID0, type RO, offset 0xFE0, reset 0x0000.0022 (see page 393) PID0 SSIPeriphID1, type RO, offset 0xFE4, reset 0x0000.0000 (see page 394) PID1 SSIPeriphID2, type RO, offset 0xFE8, reset 0x0000.0018 (see page 395) PID2 July 14, 2014 489 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SSIPeriphID3, type RO, offset 0xFEC, reset 0x0000.0001 (see page 396) PID3 SSIPCellID0, type RO, offset 0xFF0, reset 0x0000.000D (see page 397) CID0 SSIPCellID1, type RO, offset 0xFF4, reset 0x0000.00F0 (see page 398) CID1 SSIPCellID2, type RO, offset 0xFF8, reset 0x0000.0005 (see page 399) CID2 SSIPCellID3, type RO, offset 0xFFC, reset 0x0000.00B1 (see page 400) CID3 Inter-Integrated Circuit (I2C) Interface I2C Master I2C 0 base: 0x4002.0000 I2CMSA, type R/W, offset 0x000, reset 0x0000.0000 SA R/S I2CMCS, type RO, offset 0x004, reset 0x0000.0000 (Reads) BUSBSY IDLE ARBLST DATACK ADRACK ERROR BUSY ACK STOP START RUN I2CMCS, type WO, offset 0x004, reset 0x0000.0000 (Writes) I2CMDR, type R/W, offset 0x008, reset 0x0000.0000 DATA I2CMTPR, type R/W, offset 0x00C, reset 0x0000.0001 TPR I2CMIMR, type R/W, offset 0x010, reset 0x0000.0000 IM I2CMRIS, type RO, offset 0x014, reset 0x0000.0000 RIS I2CMMIS, type RO, offset 0x018, reset 0x0000.0000 MIS I2CMICR, type WO, offset 0x01C, reset 0x0000.0000 IC I2CMCR, type R/W, offset 0x020, reset 0x0000.0000 SFE 490 MFE LPBK July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 FBR TREQ RREQ Inter-Integrated Circuit (I2C) Interface I2C Slave I2C 0 base: 0x4002.0000 I2CSOAR, type R/W, offset 0x800, reset 0x0000.0000 OAR I2CSCSR, type RO, offset 0x804, reset 0x0000.0000 (Reads) I2CSCSR, type WO, offset 0x804, reset 0x0000.0000 (Writes) DA I2CSDR, type R/W, offset 0x808, reset 0x0000.0000 DATA I2CSIMR, type R/W, offset 0x80C, reset 0x0000.0000 DATAIM I2CSRIS, type RO, offset 0x810, reset 0x0000.0000 DATARIS I2CSMIS, type RO, offset 0x814, reset 0x0000.0000 DATAMIS I2CSICR, type WO, offset 0x818, reset 0x0000.0000 DATAIC Analog Comparators Base 0x4003.C000 ACMIS, type R/W1C, offset 0x000, reset 0x0000.0000 (see page 444) IN2 IN1 IN0 IN2 IN1 IN0 IN2 IN1 IN0 ACRIS, type RO, offset 0x004, reset 0x0000.0000 (see page 445) ACINTEN, type R/W, offset 0x008, reset 0x0000.0000 (see page 446) ACREFCTL, type R/W, offset 0x010, reset 0x0000.0000 (see page 447) EN RNG VREF ACSTAT0, type RO, offset 0x020, reset 0x0000.0000 (see page 448) OVAL ACSTAT1, type RO, offset 0x040, reset 0x0000.0000 (see page 448) OVAL ACSTAT2, type RO, offset 0x060, reset 0x0000.0000 (see page 448) OVAL July 14, 2014 491 Texas Instruments-Production Data Register Quick Reference 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ACCTL0, type R/W, offset 0x024, reset 0x0000.0000 (see page 449) ASRCP ISLVAL ISEN CINV ISLVAL ISEN CINV ISLVAL ISEN CINV ACCTL1, type R/W, offset 0x044, reset 0x0000.0000 (see page 449) ASRCP ACCTL2, type R/W, offset 0x064, reset 0x0000.0000 (see page 449) ASRCP 492 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller C Ordering and Contact Information C.1 Ordering Information ® The figure below defines the full set of potential orderable part numbers for all the Stellaris LM3S microcontrollers. See the Package Option Addendum for the valid orderable part numbers for the LM3S600 microcontroller. LM3Snnnn–gppss–rrm Part Number nnn = Sandstorm-class parts nnnn = All other Stellaris® parts Temperature E = –40°C to +105°C I = –40°C to +85°C Revision Speed 20 = 20 MHz 25 = 25 MHz 50 = 50 MHz 80 = 80 MHz Package BZ = 108-ball BGA QC = 100-pin LQFP QN = 48-pin LQFP QR = 64-pin LQFP C.2 Shipping Medium T = Tape-and-reel Omitted = Default shipping (tray or tube) Part Markings The Stellaris microcontrollers are marked with an identifying number. This code contains the following information: ■ The first line indicates the part number, for example, LM3S9B90. ■ In the second line, the first eight characters indicate the temperature, package, speed, revision, and product status. For example in the figure below, IQC80C0X indicates an Industrial temperature (I), 100-pin LQFP package (QC), 80-MHz (80), revision C0 (C0) device. The letter immediately following the revision indicates product status. An X indicates experimental and requires a waiver; an S indicates the part is fully qualified and released to production. ■ The remaining characters contain internal tracking numbers. C.3 Kits The Stellaris Family provides the hardware and software tools that engineers need to begin development quickly. July 14, 2014 493 Texas Instruments-Production Data Ordering and Contact Information ■ Reference Design Kits accelerate product development by providing ready-to-run hardware and comprehensive documentation including hardware design files ■ Evaluation Kits provide a low-cost and effective means of evaluating Stellaris microcontrollers before purchase ■ Development Kits provide you with all the tools you need to develop and prototype embedded applications right out of the box See the website at www.ti.com/stellaris for the latest tools available, or ask your distributor. C.4 Support Information For support on Stellaris products, contact the TI Worldwide Product Information Center nearest you: http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm. 494 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller D Package Information D.1 48-Pin LQFP Package D.1.1 Package Dimensions Figure D-1. Stellaris LM3S600 48-Pin LQFP Package Note: The following notes apply to the package drawing. July 14, 2014 495 Texas Instruments-Production Data Package Information 1. All dimensions are in mm. 2. Dimensions shown are nominal with tolerances indicated. 3. Foot length "L" is measured at gage plane 0.25 mm above seating plane. 4. L/F: Eftec 64T Cu or equivalent, 0.127 mm (0.005") thick. Package Type Symbol 48LD LQFP Note MIN MAX A - 1.60 A1 0.05 0.15 A2 - 1.40 D 9.00 D1 7.00 E 9.00 E1 7.00 L 0.60 e 0.50 b 0.22 theta 0° - 7° ddd 0.08 ccc 0.08 JEDEC Reference Drawing MS-026 Variation Designator BBC 496 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller D.1.2 Tray Dimensions Figure D-2. 48-Pin LQFP Tray Dimensions July 14, 2014 497 Texas Instruments-Production Data Package Information 498 July 14, 2014 Texas Instruments-Production Data ® Stellaris LM3S600 Microcontroller D.1.3 Tape and Reel Dimensions Figure D-3. 48-Pin LQFP Tape and Reel Dimensions July 14, 2014 499 Texas Instruments-Production Data PACKAGE OPTION ADDENDUM www.ti.com 13-Apr-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) LM3S600-IQN50-C2 NRND LQFP PT 48 250 RoHS & Green NIPDAU Level-3-260C-168 HR -40 to 85 LM3S600 IQN50 PT (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of